Sanyo PDG-DHT8000L - 8000 Lumens, PDG-DHT8000L Specifications

Page 1

EXPAND SERIAL COMMAND FUNCTIONAL SPECIFICATIONS

PDG-DHT8000L

Ver.1.00

SANYO Electric Co., Ltd DS Company Projector Business Division

Page 2

1. Overview	10
2. Serial Interface Specification	10
2.1 Transfer Specification	10
2.2 Connection	10
3. Notes for communication	11
4. Notation	12
5. Functional Execution Command Table	13
5.1 Image Command Table	13
5.2 PC Control Command Table	13
5.3 Input Control Command Table	14
5.4 Screen Command Table	14
5.5 Lamp Command Table	14
5.6 Setting Command Table	14
5.7 Other Command Table	16
6. Status Read Command Table	16
6.1 Image Status Read Command Table	16
6.2 PC Status Read Command Table	16
6.3 Video Status Read Command Table	17
6.4 Input Status Read Command Table	17
6.5 Screen Status Read Command Table	17
6.6 Lamp Status Read Command Table	17
6.7 Setting Status Read Command Table	18
6.8 Other Status Read Command Table	19
7. Error Code Table	20
8. Functional Execution Command	21
8.1 Format	21
8.2 Transfer Example	21
8.3 Operation Requirements	21
8.4 Image Command
8.4.1 CF_ CONT Command
8.4.2 CF_ BRIGHT Command
8.4.3 CF_COLOR Command
8.4.4 CF_TINT Command
8.4.5 CF_COLMNSAV Command	23
8.4.6 CF_COLMNLD Command	23
8.4.7 CF_APCTRL Command	23
8.4.8 CF_COLTEMP Command	23
8.4.9 CF_WBAL- Command	24
8.4.10 CF_OFFSET- Command	24

Page 3

8.4.11 CF_SHARP Command	24
8.4.12 CF_GAMMA Command	25
8.4.13 CF_NZRED Command	25
8.4.14 CF_PROGV Command	25
8.4.15 CF_BCOLOR Command	25
8.4.16 CF_IMAGE Command	26
8.4.17 CF_IMAGEADJ Command	26
8.5 PC Control Command	27
8.5.1 CF_FSYNC Command	27
8.5.2 CF_TDOTS Command	27
8.5.3 CF_H-POS Command	27
8.5.4 CF_V-POS Command	28
8.5.5 CF_CLAMP Command	28
8.5.6 CF_DDOTS Command	28
8.5.7 CF_DLINE Command	29
8.5.8 CF_SETPCADJ Command	29
8.5.9 CF_ORGMODE Command	29
8.5.10 CF_PCSTORE Command	30
8.5.11 CF_PCMODEFREE Command	30
8.6 Input Control Command	31
8.6.1 CF_INPUT Command	31
8.6.2 CF_SOURCE Command	31
8.6.3 CF_INPUT1~4 Command	31
8.6.4 CF_SYSTEM Command	32
8.7 Screen Control Command	33
8.7.1 CF_SCREEN Command	33
8.7.2 CF_DZCENT Command	33
8.7.3 CF_KEYSTONE Command	34
8.7.4 CF_KEYSTONEMODE Command	34
8.7.5 CF_CEIL Command	34
8.7.6 CF_REAR Command	35
8.7.7 CF_VSCALE Command	35
8.7.8 CF_VPOS Command	35
8.7.9 CF_HSCALE Command	36
8.7.10 CF_HPOS Command	36
8.8 Lamp Command	37
8.8.1 CF_LAMPMODE Command	37
8.8.2 CF_AUTOLAMPCONTRL Command	37
8.8.3 CF_LAMPLIFECONTRL Command	37
8.8.4 CF LAMPINTERVAL Command	37

Page 4

8	9 Setting Command	.38
	8.9.1 CF_LANG Command	.38
	8.9.2 CF_ MENUPOSITION Command	.38
	8.9.3 CF_SIMPLEMENU Command	.38
	8.9.4 CF_MENUSIZE Command	39
	8.9.5 CF_DISP Command	.39
	8.9.6 CF_BACKGND Command	.39
	8.9.7 CF_PIP Command	.39
	8.9.8 CF_PIPMODE Command	.40
	8.9.9 CF_PIPMAININP Command	.40
	8.9.10 CF_PIPSUBINPU Command	.41
	8.9.11 CF_PIPSIZE Command	.41
	8.9.12 CF_PIPPOSITION Command	.42
	8.9.13 CF_PIPFRAMELOCK Command	.42
	8.9.14 CF_PIPSTORE Command	.42
	8.9.15 CF_PIPMODEFREE Command	.43
	8.9.16 CF_PIPRST Command	.43
	8.9.17 CF_EDGEBLENDING Command	43
	8.9.18 CF_BLEND Command	.43
	8.9.19 CF_BLENDBLK Command	44
	8.9.20 CF_BLENDBLKALL Command	44
	8.9.21 CF_BLENDTESTPAT Command	44
	8.9.22 CF_BLENDRST Command	44
	8.9.23 CF_BLENDMENUOFF Command	.45
	8.9.24 CF_BLENDMENU Command	.45
	8.9.25 CF_COLORMATCHING Command	.45
	8.9.26 CF_CMMSXY Command	.45
	8.9.27 CF_CMMSL Command	46
	8.9.28 CF_CMTGXY Command	46
	8.9.29 CF_CMTGG Command	46
	8.9.30 CF_CMAUTOTESTPAT Command	47
	8.9.31 CF_CMRST Command	47
	8.9.32 CF_CMSTORE Command	47
	8.9.33 CF_CMMSTESTPAT Command	47
	8.9.34 CF_CMTGTESTPAT Command	48
	8.9.35 CF_CMFDEFAULT Command	48
	8.9.36 CF_CMMENUOFF Command	48
	8.9.37 CF_CMMENU Command	48
	8.9.38 CF_DYNAMICBLACK Command	.49
	8.9.39 CF_HDMISETUP Command	49

Page 5

8.9.40 CF_LOGO Command	49
8.9.41 CF_FANSPEED Command	50
8.9.42 CF_RCODE Command	50
8.9.43 CF_RSENS Command	50
8.9.44 CF_P-MANE Command	51
8.9.45 CF_P-MANETIME Command	51
8.9.46 CF_ON-STA Command	51
8.9.47 CF_PJPINCODE Command	52
8.9.48 CF_FILH Command	52
8.9.49 CF_FILTIMER Command	52
8.9.50 CF_FILCTL Command	52
8.9.51 CF_FILSCRL Command	53
8.9.52 CF_TESTPAT Command	53
8.9.53 CF_FDEFAULT Command	53
8.9.54 CF_KEYDIS Command	53
8.9.55 CF_SHUTRCPROT Command	54
8.9.56 CF_SHUTKEYPROT Command	54
8.9.57 CF_SHUTH Command	54
8.9.58 CF_SHUTEFFECT Command	54
8.9.59 CF_SHUTRELEASE Command	55
8.9.60 CF_DELAYCTRL Command	55
8.9.61 CF_CCAPTIONDISP Command	55
8.9.62 CF_CCAPTIONCOLOR Command	56
8.9.63 CF_FRAMELOCK Command	56
8.9.64 CF_FRAMELOCKADJ Command	56
8.9.65 CF_FRAMELOCKRST Command	56
8.10 Other Command	57
8.10.1 CF_KEYEMU Command	57
8.10.2 CF_MENU Command	57
8.10.3 CF_POWER Command	58
8.10.4 CF_FREEZE Command	58
8.10.5 CF_VMUTE Command	58
9. Status Read Command	59
9.1 Format	59
9.2 Transfer Example	59
9.3 Operation condition	59
9.4 Image Status Read Commands	60
9.4.1 CR_CONT Command	60
9.4.2 CR_BRIGHT Command	60
9.4.3 CR_COLOR Command	60

Page 6

	9.4.4 CR_TINT Command	60
	9.4.5 CR_APCTRL Command	60
	9.4.6 CR_COLTEMP Command	61
	9.4.7 CR_WBAL-R Command	61
	9.4.8 CR_WBAL-G Command	61
	9.4.9 CR_WBAL-B Command	61
	9.4.10 CR_OFFSET-R Command	61
	9.4.11 CR_OFFSET-G Command	61
	9.4.12 CR_OFFSET-B Command	62
	9.4.13 CR_SHARP Command	62
	9.4.14 CR_GAMMA Command	62
	9.4.15 CR_NZRED Command	62
	9.4.16 CR_PROGV Command	62
	9.4.17 CR_BCOLOR Command	63
	9.4.18 CR_IMAGE Command	63
	9.4.19 CR_IMGGMD Command	63
9	.5 PC Status Read Commands	64
	9.5.1 CR_FSYNC Command	64
	9.5.2 CR_TDOTS Command	64
	9.5.3 CR_H-POS Command	64
	9.5.4 CR_V-POS Command	64
	9.5.5 CR_CLAMP Command	65
	9.5.6 CR_DDOTS Command	65
	9.5.7 CR_DLINE Command	65
	9.5.8 CR_SETPCADJ Command	66
	9.5.9 CR_ORGMODE Command	67
	9.5.10 CR_PCSTORE Command	67
9	.6 Video Status Read Command	68
	9.6.1 CR_SERSYS Command	68
9	.7 Input Read Command	69
	9.7.1 CR_INPUT Command	69
	9.7.2 CR_SOURCE Command	69
	9.7.3 CR_SYSTEM Command	70
	9.7.4 CR_SYSLIST Command	71
	9.7.5 CR_MODELIST Command	72
	9.7.6 CR_SRCINP1 Command	72
	9.7.7 CR_SRCINP2 Command	72
	9.7.8 CR_SRCINP3 Command	72
	9.7.9 CR_SRCINP4 Command	73
	9.7.10 CR HMSLOT Command	73

Page 7

9.7.11 CR_NMSLOT1 Command	73
9.7.12 CR_NMSLOT2 Command	73
9.7.13 CR_NMSLOT3 Command	73
9.7.14 CR_NMSLOT4 Command	74
9.7.15 CR_IDSLOT1 Command	74
9.7.16 CR_IDSLOT2 Command	74
9.7.17 CR_IDSLOT3 Command	74
9.7.18 CR_IDSLOT4 Command	75
9.8 Screen Status Read Commands	76
9.8.1 CR_SCREEN Command	76
9.8.2 CR_KYSTNMODE Command	76
9.8.3 CR_CEIL Command	76
9.8.4 CR_REAR Command	76
9.8.5 CR_VSCALE Command	76
9.8.6 CR_VPOS Command	77
9.8.7 CR_HSCALE Command	77
9.8.8 CR_HPOS Command	77
9.9 Lamp Status Read Commands	78
9.9.1 CR_LAMPREPL Command	78
9.9.2 CR_LAMPMODE Command	78
9.9.3 CR_AUTOLAMPCONTRL Command	78
9.9.4 CR_LAMPSTS Command	78
9.9.5 CR_INFLAMP Command	79
9.9.6 CR_PROJH Command	79
9.9.7 CR_HMLAMP Command	79
9.9.8 CR_LAMPH Command	79
9.9.9 CR_LAMPCORRESPH Command	80
9.9.10 CR_LAMPINTERVAL Command	80
9.9.11 CR_LAMPLIFECONTRL Command	80
9.10 Setting Status Read Commands	81
9.10.1 CR_LANG Command	81
9.10.2 CR_SIMPLEMENU Command	81
9.10.3 CR_MENUSIZE Command	81
9.10.4 CR_DISP Command	81
9.10.5 CR_BACKGND Command	82
9.10.6 CR_LOGO Command	82
9.10.7 CR_LOGOLOCK Command	82
9.10.8 CR_FANSPEED Command	82
9.10.9 CR_RCODE Command	82

Page 8

9.10.11 CR_P-MANE Command	83
9.10.12 CR_P-MANETIME Command	83
9.10.13 CR_ONSTA Command	83
9.10.14 CR_SECURITY Command	83
9.10.15 CR_PJLOCKNOW Command	84
9.10.16 CR_PJLOCMENU Command	84
9.10.17 CR_FILH Command	84
9.10.18 CR_FILCOND Command	84
9.10.19 CR_FILREPL Command	84
9.10.20 CR_FILTIMER Command	85
9.10.21 CR_FILREMAIN Command	85
9.10.22 CR_TESTPAT Command	85
9.10.23 CR_KEYDIS Command	85
9.10.24 CR_SHUTRCPROT Command	86
9.10.25 CR_SHUTKEYPROT Command	86
9.10.26 CR_SHUTH Command	86
9.10.27 CR_SHUTEFFECT Command	86
9.10.28 CR_SHUTRELEASE Command	86
9.10.29 CR_DELAYCTRL Command	87
9.10.30 CR_CCAPTIONSIDP Command	87
9.10.31 CR_CCAPTIONCOLOR Command	87
9.10.32 CR_FRAMELOCK Command	87
9.10.33 CR_FRAMELOCKADJ Command	88
9.10.34 CR_PIP Command	88
9.10.35 CR_PIPMODE Command	88
9.10.36 CR_PIPMAININP Command	89
9.10.37 CR_PIPSUBINPU Command	89
9.10.38 CR_PIPSIZE Command	90
9.10.39 CR_PIPFRAMELOCK Command	90
9.10.40 CR_PIPSTORE Command	90
9.10.41 CR_EDGEBLENDING Command	90
9.10.42 CR_EDGEBLENDING Command	91
9.10.43 CR_BLENDBLK Command	91
9.10.44 CR_BLENDTESTPAT Command	91
9.10.45 CR_COLORMATCHING Command	91
9.10.46 CR_CMMSXY_%1 Command	92
9.10.47 CR_CMMSL_%1 Command	92
9.10.48 CR_CMTGXY_%1 Command	92
9.10.49 CR_CMTGG_%1 Command	93
	03

Page 9

9.10.51 CR CMMSTESTPAT Command
9.10.52 CR CMTGTESTPAT Command
9.10.53 CR DYNAMICBLACK Command
9.10.54 CR HDMISETUP Command
9.11 Other Status Read Commands
9.11.1 CR_STATUS Command	95
9.11.2 CR_SIGNAL Command	95
9.11.3 CR_VMUTE Command	95
9.11.4 CR_FREEZE Command	95
9.11.5 CR_P-TIMER Command	96
9.11.6 CR_TEMPWARN Command	96
9.11.7 CR_TEMPFAIL Command	97
9.11.8 CR_TEMP Command
9.11.9 CR_SERIALNO Command	98
9.11.10 CR_SHUTCOND Command	98
9.11.11 CR_OPTCTRLNO Command	99
9.11.12 CR_LENSTYPE Command
9.11.13 CR_COLWHEELTYPE Command
10. Command with Address Specification	100
10.1. Overview	100
10.2. Functional Execution Command with address	100
10.2.1. Format	100
10.2.2. When the command pipelining is needed	101
10.3. Status Read Command with Address	101
10.3.1. Format

Page 10

1. Overview

This Functional Specification defines communication for PDG-DHT8000L.
Most commands are also available to remote-control a projector through RS-232C from a computer. Therefore, commands are defined as Expand Serial Commands.
The operation by some commands depends on Optional Board installed in Input Slot of the projector.
This document assumes that Option Boards are installed.

2. Serial Interface Specification

2.1 Transfer Specification

ltems	Specification
Synchronous System	Asynchronous
Transmission Speed	9600 / 19200
Data Length	8 bit
Parity	N/A
Stop Bit	1
Flow Control	N/A

1) Transmission Speed: initial setting value is 19200

2) Transmission Speed can be changed in Service Mode

2.2 Connection

Dedicated serial cables that come with a projector must be used for the connection between a

computer and the projector.

Connect COM port of the computer to SERIAL PORT IN of the projector.

COM Port (COM1 or COM2) of a computer is specified by control software of the computer.

Page 11

3. Notes for communication

Expand Serial Command is defined as a single command per line that starts with "C" and ends with carriage return (0x0D).
When a projector receives carriage return (0x0D), it starts decoding.
There are two types of commands as below:

Example of Functional Execution Command:"CF BRIGHT 032" [CR]

Example of Status Read Command: "CR BRIGHT" [CR]

Note) "" indicates a space

It clears the information of buffer in the following cases:
- when the projector receives LF (0x0A) or EOF (0x1A).
- when it takes more than one second to receive a single command
  - (Until receiving the carriage return after the reception of the first data)
The projector processes the command and returns the response within a few ms to 8000 ms after the reception of the command. When several commands are sent in succession, do not send another command unless the response to the previous command has been returned. Need to confirm that the processing of the current command has been completed and returned the response before sending another command.

Note) when the computer sends another command before the previous response has been returned, the projector may not operate properly.

Note) when the current command processing has not completed, another command process can not be accepted by the projector

Normally it is less than 1000ms for the completion of receiving a command and returning the response, but it takes more than 1000ms for some Functional Execution Commands as listed below:

Command	ltem
CF_IMAGE	Select Image Mode
CF_INPUT	Select Input
CF_SCREEN	Select Screen Size
CF_SYSTEM	Select System
CF_INPUT1	Select Input 1 and Signal (concurrent execution)
CF_INPUT2	Select Input 2 and Signal
CF_INPUT3	Select Input 3 and Signal
CF_INPUT4	Select Input 4 and Signal
CF_IMAGEADJ	Reset/Store for Image Adjustment

· It takes about 8 seconds for internal initialization after plugging in AC power. During this time it

cannot process commands. Do not issue any command.

Page 12

4. Notation

Data from a controller to a projector is represented as COMMAND, and data from a projector to a controller in response to the incoming command is represented as RESPONSE.
[CR]: Carriage Return Code

The command ends with carriage return code.

The response also ends with carriage return code.

• _: Space Code

All space code is indicated by ( ).

• %1: Parameter included in command

When there is more than one parameter, they are represented as %2, %3...

Page 13

5. Functional Execution Command Table

5.1 Image Command Table

Execute command	ltem
CF_CONT_%1[CR]	Set value of Contrast
CF_BRIGHT_%1[CR]	Set value of Brightness
CF_COLOR_%1[CR]	Set value of Color
CF_TINT_%1[CR]	Set value of Tint
CF_COLMNSAV_%1[CR]	Set area to store current values of Color Management
CF_COLMNLD_%1[CR]	Set area to load values of Color Management
CF_APCTRL_%1[CR]	Set level of Auto Picture Control
CF_COLTEMP_%1[CR]	Set level of Color Temperature
CF_WBAL-R_%1[CR]	Set Red value of White Balance
CF_WBAL-G_%1[CR]	Set Green value of White Balance
CF_WBAL-B_%1[CR]	Set Blue value of White Balance
CF_OFFSET-R_%1 [CR]	Set Red value of Offset
CF_OFFSET-G_%1 [CR]	Set Green value of Offset
CF_OFFSET-B_%1 [CR]	Set Blue value of Offset
CF_SHARP_%1[CR]	Set value of Sharpness
CF_GAMMA_%1[CR]	Set value of Gamma
CF_NZRED_%1[CR]	Set ON/OFF of Noise reduction
CF_PROGV_%1[CR]	Set mode of Progressive scan
CF_BCOLOR_%1[CR]	Set ON/OFF of Brilliant Color
CF_IMAGE_%1[CR]	Set Image mode
CF_IMAGEADJ_%1[CR]	Set Store/Reset of values in Image Adjustment

5.2 PC Control Command Table

Execute command	ltem
CF_FSYNC_%1[CR]	Set value of Fine Sync
CF_TDOTS_%1[CR]	Set value of Total Dots
CF_H-POS_%1[CR]	Set value of Horizontal Position
CF_V-POS_%1[CR]	Set value of Vertical Position
CF_CLAMP_%1[CR]	Set value of Clamp
CF_DDOTS_%1[CR]	Set value of Display Dots
CF_DLINE_%1[CR]	Set value of Display Line
CF_SETPCADJ_%1[CR]	Apply values set in PC Adjust menu to screen image
CF_ORGMODE_%1[CR]	Specify the original signal for the selected PC mode
CF_PCSTORE_%1[CR]	Store current setting values in PC Adjust menu to Mode %1
CF_PCMODEFREE_%1 [CR]	Delete the values registered in Mode %1 and return it to Free status.

Page 14

5.3 Input Control Command Table

Execute command	ltem
CF_INPUT_%1[CR]	Select Input
CF_SOURCE_%1[CR]	Select Source of selected Input
CF_INPUT1_%1[CR]	Select Input1 and also set input source to %1
CF_INPUT2_%1[CR]	Select Input2 and also set input source to %1
CF_INPUT3_%1[CR]	Select Input3 and also set input source to %1
CF_INPUT4_%1[CR]	Select Input4 and also set input source to %1
CF_SYSTEM_%1[CR]	Select System in Video input mode

5.4 Screen Command Table

Execute command	Item
CF_SCREEN_%1[CR]	Select Screen size
CF_DZCENT _%1[CR]	Cancel Digital Zoom mode
CF_KEYSTONE _%1[CR]	Set Keystone correction
CF_KYSTNMODE _%1 [CR]	Set Keystone store mode
CF_CEIL_%1[CR]	Set ON/OFF of Ceiling
CF_REAR_%1[CR]	Set ON/OFF of Rear
CF_VSCALE_%1[CR]	Set V Scale
CF_VPOS_%1[CR]	Set V Position
CF_HSCALE_%1[CR]	Set H Scale
CF_HPOS_%1[CR]	Set H Position

5.5 Lamp Command Table

Execute command	Item
CF_LAMPMODE_%1[CR]	Select lamp mode
CF_AUTOLAMPCONTRL_%1[CR]	Switch dimmer function levels of Normal/Auto/Eco
CF_LAMPLIFECONTROL_%1[CR]	Select Lamp life control
CF_LAMPINTERVAL_%1[CR]	Set Lamp interval

5.6 Setting Command Table

Execute command	Item
CF_LANG_%1[CR]	Select language for OSD
CF_MENUPOSITION_%1[CR]	Control of Menu position
CF_SIMPLEMENU_%1[CR]	Set ON/OFF of Simple menu
CF_MENUSIZE_%1[CR]	Set Menu size
CF_DISP_%1[CR]	Set ON/OFF of On Screen Display
CF_BACKGND_%1[CR]	Select screen for no signal
CF_PIP_%1[CR]	Set "Picture in Picture"
CF_PIPMODE_%1[CR]	Set mode of "Picture in Picture"
CF_PIPMAININP_%1_%2[CR]	Select Input and Source of "Picture in Picture" (Main picture)
CF_PIPSUBINP_%1_%2[CR]	Select Input and Source of "Picture in Picture" (Sub picture)
CF_PIPSIZE_&1[CR]	Set menu size of "Picture in Picture"
CF_PIPPOSITION_%1[CR]	Set position of "Picture in Picture"
CF_PIPFRAMELOCK_%1[CR]	Set Frame lock of "Picture in Picture"
CF_PIPSTORE_%1[CR]	Store current status of "Picture in Picture" to User1-5

Page 15

CF_PIPMODEFREE_%1[CR]	Delete the values registered in User %1 and return it
CF PIPRST %1[CR]	Reset setting of "Picture in Picture"
CF EDGEBLENDING %1[CR]	Set Edge blending
CF BLEND %1 %2[CR]	Set width of Edge blending
CF BLENDBLK %1 %2[CR]	Set Black level(R/G/B) of Edge blending
CF_BLENDBLKALL_%1_%2[CR]	Set Black level(ALL) of Edge blending
CF_BLENDTESTPAT_%1[CR]	Set Test pattern of Edge blending
CF_BLENDRST_%1[CR]	Reset Edge blending
CF_BLENDMENUOFF_%1[CR ]	Set Menu off of Edge blending
CF_BLENDMENU_%1[CR ]	Select display or erase Edge blending menu.
CF_COLORMATCHING_%1[CR]	Set Color matching
CF_CMMSXY_%1_%2_%3[CR]	Set "x,y" value of Measured of Color matching
CF_CMMSL_%1_%2[CR]	Set "L" value of Measured of Color matching
CF_CMTGXY_%1_%2_%3[CR]	Set "x,y" value of Target of Color matching
CF_CMTGG_%1_%2[CR]	Set "g" value of Target of Color matching
CF_CMAUTOTESTPAT_%1[CR]	Set Auto test pattern of Color matching
CF_CMRST_%1[CR]	Reset Color matching
CF_CMSTORE_%1[CR]	Store Color matching
CF_CMMSTESTPAT_%1[CR]	Display Measured Test pattern of Color matching
CF_CMTGTESTPAT_%1[CR]	Display Target Test pattern of Color matching
CF_CMFDEFAULT_%1[CR]	Return color matching setting to Factory Default setting.
CF_CMMENUOFF_%1[CR]	Set Menu off of Color matching
CF_CMMENU_%1[CR]	Select display or erase Color matching menu
CF_DYNAMICBLACK_%1[CR]	Set DynamicBlack
CF_HDMISETUP_%1[CR]	Set HDMI setup
CF_LOGO_%1[CR]	Set ON/OFF of Logo
CF_FANSPEED_%1[CR]	Select Fan Speed
	Select Remote Control Code
CF_RSENS_%1[CR]	control
CF_P-MANE_%1[CR]	Set ON/OFF of Power Management
CF_P-MANETIME_%1[CR]	Set time of Power Management
	Set ON/OFF of Power ON Start
	Enter PJ PIN code to cancel PJ lock
	Reset Filter used time
CF_FILTIMER_%1[CR]	warning on screen
CF_FILCTL_%1[CR]	Execute operation of scroll of filter
CF_FILSCRL_%1[CR]	Reset Filter scroll counter
CF_TESTPAT_%1[CR]	Set Test pattern display function
CF_FDEFAULT_%1[CR]	Return the settings to Factory Default status
CF_KEYDIS_%1[CR]	Set limitation of RC/KEY control
CF_SHUTRCPROT_%1[CR]	Set valid / invalid of RC use on Shutter control function
CF_SHUTKEYPROT_%1[CR]	Set valid / invalid use of key on the side panel on Shutter control function
CF_SHUTH_%1[CR]	Set time of operating shutter management function
CF_SHUTEFFECT_%1[CR]	Set effect when opening/closing shutter
CF_SHUTRELEASE_%1[CR]	Set release key of Shutter
CF_DELAYCTRL_%1[CR]	Set Video delay control function

Page 16

CF_CCAPTIONDISP_%1[CR]	Set channel of Closed caption
CF_CCAPTIONCOLOR_%1[CR]	Set color of Closed caption
CF_FRAMELOCK_%1[CR]	Set Frame lock function
CF_FRAMELOCKADJ_%1[CR]	Set frame lock frequency
CF_FRAMELOCKRST_%1[CR]	Reset Frame lock setting

5.7 Other Command Table

Execute command	Item
CF_KEYEMU_%1[CR]	Control RC/Panel key operation of Pointer(Right/Left/Top/Bottom)/SELECT/AUTO PC
CF_MENU_%1[CR]	Set ON/OFF of Menu
CF_POWER_%1[CR]	Set ON/OFF of Power
CF_FREEZE_%1[CR]	Set ON/OFF of Freeze
CF_VMUTE_%1[CR]	Control Open/Close of Shutter

6. Status Read Command Table

6.1 Image Status Read Command Table

Status read command	Item
CR_CONT [CR]	Get value of Contrast
CR_BRIGHT [CR]	Get value of Brightness
CR_COLOR [CR]	Get value of Color
CR_TINT [CR]	Get value of Tint
CR_APCTRL	Get setting status of Auto Picture Control
CR_COLTEMP	Get value of Color temperature
CR_WBAL-R [CR]	Get Red value of White Balance
CR_WBAL-G [CR]	Get Green value of White Balance
CR_WBAL-B [CR]	Get Blue value of White Balance
CR_OFFSET-R [CR]	Get Offset Red
CR_OFFSET-G [CR]	Get Offset Green
CR_OFFSET-B [CR]	Get Offset Blue
CR_SHARP [CR]	Get value of Sharpness
CR_GAMMA [CR]	Get value of Gamma
CR_NZRED [CR]	Get setting status of Noise reduction
CR_PROGV [CR]	Get setting status of Progressive scan
CR_BCOLOR [CR]	Get setting status of BrilliantColor
CR_IMAGE [CR]	Get Selected Image status
CR_IMGGMD [CR]	Get setting value of Image Gamma

6.2 PC Status Read Command Table

Status read command	Item
CR_FSYNC [CR]	Get setting value of Fine Sync
CR_TDOTS [CR]	Get setting value of Total Dots
CR_CLAMP [CR]	Get setting value of Clamp
CR_H-POS [CR]	Get setting value of Horizontal Position
CR_V-POS [CR]	Get setting value of Vertical Position
CR_DDOTS [CR]	Get setting value of Display Dots
CR_DLINE [CR]	Get setting value of Display Line

Page 17

CR_SETPCADJ [CR]	Get currently displayed signal
CR_ORGMODE [CR]	Get the original signal of the mode adjusted in PC Adj.
CR_PCSTORE [CR]	Get Free or Stored status for PC Adj. Mode 1-5

6.3 Video Status Read Command Table

Status read command	lter	n
CR_SERSYS [CR]	Get currently selected signal. result by Auto detection.	In Auto mode, it returns a

6.4 Input Status Read Command Table

Status read command	Item
CR_INPUT [CR]	Get selected Input
CR_SOURCE [CR]	Get selected Source
CR_SYSTEM [CR]	Get selected System in Video Input mode
CR_SYSLIST[CR]	Get possible system list
CR-MODELIST[CR]	Get possible mode list
CR_SRCINP1 [CR]	Get selected source for Input 1
CR_SRCINP2 [CR]	Get selected source for Input 2
CR_SRCINP3 [CR]	Get selected source for Input 3
CR_SRCINP4 [CR]	Get selected source for Input 4
CR_HMSLOT [CR]	Get the total number of Slots
CR_NMSLOT1 [CR]	Get a card name inserted to Slot 1
CR_NMSLOT2 [CR]	Get a card name inserted to Slott2
CR_NMSLOT3 [CR]	Get a card name inserted to Slot 3
CR_NMSLOT4 [CR]	Get a card name inserted to Slot 4
CR_IDSLOT1 [CR]	Get ID information of Slot 1
CR_IDSLOT2 [CR]	Get ID information of Slot 2
CR_IDSLOT3 [CR]	Get ID information of Slot 3
CR_IDSLOT4 [CR]	Get ID information of Slot 4

6.5 Screen Status Read Command Table

Status read command	ltem
CR_SCREEN [CR]	Get selected screen size
CR_KYSTNMODE[CR]	Get selected Keystone store mode
CR_CEIL[CR]	Get selected ON/OFF of Ceiling
CR_REAR[CR]	Get selected ON/OFF of Rear
CR_VSCALE[CR]	Get setting status of V Scale
CR_VPOS[CR]	Get setting status of V Position
CR_HSCALE[CR]	Get setting status of H Scale
CR_HPOS[CR]	Get setting status of H Position

6.6 Lamp Status Read Command Table

Status read command	Item
CR_LAMPREPL [CR]	Get information on Lamp replacement time
CR_LAMPMODE [CR]	Get selected Lamp mode
CR_AUTOLAMPCONTROL[CR]	Get setting status of dimmer function level.
CR_LAMPSTS [CR]	Get Lamp lighting status

Page 18

CR_INFLAMP [CR]	Get Lamp switching status
CR_PROJH [CR]	Get the projector total running time
CR_HMLAMP [CR]	Get the total number of lamps
CR_LAMPH [CR]	Get information of actual Lamp running time
CR_LAMPCORRESPH [CR]	Get lamp running time multiplied by a coefficient
CR_LAMPINTERVAL [CR]	Get Lamp interval status
CR_LAMPLIFECONTROL [CR]	Get Lamp life control status

6.7 Setting Status Read Command Table

Status read command	Item
CR_LANG [CR]	Get selected language
CR_SIMPLEMENU [CR]	Get setting status of Simple menu
CR_MENUSIZE [CR]	Get setting status of Menu size
CR_DISP [CR]	Get setting status of Display
CR_BACKGND [CR]	Get setting status of Screen for no signal
CR_LOGO [CR]	Get setting status of Logo
CR_LOGOLOCK [CR]	Get setting status of Logo Lock
CR_FANSPEED [CR]	Get selected Fan Control Speed
CR_RCODE [CR]	Get selected Remote Control Code
CR_RSENS [CR]	Get selected location of infrared remote receiver of remote control
CR_P-MANE [CR]	Get setting status of Power management
CR_P-MANETIME [CR]	Get setting time for Power Management
CR_ON-STA [CR]	Get setting status of ON Start
CR_SECURITY [CR]	Get setting status of Security
CR_PJLOCKNOW [CR]	Get setting status of current PJ Lock
CR_PJLOCKMENU [CR]	Get PJ Lock setting status on the menu
CR_FILH[CR]	Get Filter used time
CR_FILCOND[CR]	Get status of filter clog
CR_FILREPL[CR]	Get status of Filter cleaning / replacement time
	Get time to display Filter cleaning / replacement warning on screen
CR_FILREMAIN[CR]	Get remaining number of usable Filter scroll
CR_TESTPAT[CR]	Get setting status of Test pattern
CR_KEYDIS [CR]	Get setting status of RC/KEY control limitation
CR_SHUTRCPROT[CR]	Get remote controller disability status of the shutter
CR_SHUTKEYPROT[CR]	Get Key controller disability state of the shutter
CR_SHUTH[CR]	Get time setting to begin the shutter management
CR_SHUTEFFECT[CR]	Get status of shutter effect function
CR_SHUTRELEASE[CR]	Get setting status of release key of shutter
CR_DELAYCTRL[CR]	Get selected mode of Video delay control
CR_CCAPTIONDISP[CR]	Get setting status of channel of Closed caption
CR_CCAPTIONCOLOR[CR]	Get setting status of color of Closed caption
CR_FRAMELOCK[CR]	Get setting status of Frame lock function
CR_FRAMELOCKADJ[CR]	Get value of Frame lock frequency
CR_PIP[CR]	Get setting status of "Picture in Picture"
CR_PIPMODE[CR]	Get setting status of Mode of "Picture in Picture"
	Get setting status of Input / Source of "Picture in Picture" (Main picture)
CR_PIPSUBINP[CR]	Get setting status of Input / Source of "Picture in Picture" (Sub picture)

Page 19


	Get Menu size of "Picture in Picture"
CR_PIPFRAMELOCK[CR]	Get setting status of Frame lock of "Picture in Picture"
CR_PIPSTORE[CR]	Get stored status of "Picture in Picture"
CR_EDGEBLENDING[CR]	Get setting status of Edge blending
CR_BLEND[CR]	Get setting status of width of Edge blending
CR_BLENDBLK[CR]	Get setting status of Black level of Edge blending
CR_BLENDTESTPAT[CR]	Get setting status of Test pattern of Edge blending
	Get setting status of Color matching
CR_CMMSXY_%1[CR]	Get "x","y" value of Measured of Color matching
CR_CMMSL_%1[CR]	Get "L" value of Measured of Color matching
CR_CMTGXY_%1[CR]	Get "x","y" value of Target of Color matching
CR_CMTGG_%1[CR]	Get "g" value of Target of Color matching
CR_CMAUTOTESTPAT[CR]	Get setting status of Auto test pattern of Color matching
CR_CMMSTESTPAT[CR]	Get setting status of test pattern(Measured) of Color matching
CR_CMTGTESTPAT[CR]	Get setting status of test pattern(Target) of Color matching
	Get setting status of DynamicBlack
CR_HDMISETUP[CR]	Get setting status of HDMI setup

6.8 Other Status Read Command Table

Status read command	Item
CR_STATUS [CR]	Get operation state of the projector
CR_SIGNAL [CR]	Get status of signal existence
CR_VMUTE [CR]	Get setting status of Video mute
CR_FREEZE [CR]	Get setting status of Freeze
CR_PTIMER [CR]	Get operating status of P-Timer
CR_TEMPWARN [CR]	Get temperature status whether it is close to abnormal level or not
CR_TEMPFAIL [CR]	Get temperature in abnormal temperature status
CR_TEMP[CR]	Get current temperature
CR_SERIALNO [CR]	Get value of Serial number
CR_SHUTCOND [CR]	Get setting status of Shutter
CR_OPTCTRLNO[CR]	Get Option control No. of the projector
CR_LENSTYPE[CR]	Get Lens type currently installed
CR_COLWHEELTYPE[CR]	Get Color wheel type currently installed

Page 20

7. Error Code Table

Error Code	Contents
?	-When the received data cannot be decoded -Parameter designation error (wrong digit number, including invalid value, etc.)
000	Normal reception (This is "Not" error)
101	When the function selected is not available under current condition. ex) When receiving signal-related commands while no signal is entered
102	Specified value is out of range (Not reflected)
103	Command mismatched to Hardware (the command is for Optional function which is not implemented)
201	Incremented or decremented value or values are beyond upper or lower limits.
301	Command cannot be executed during capturing display.
402	Command cannot be executed during PIN code operation.

Page 21

8. Functional Execution Command

8.1 Format

1) PC issues a command in the format below:

: Space (To separate Command and Parameter)

2) The projector decodes the received command and when it gets ready to receive another

command, it returns the response.

"000" [CR1: (0x06, 0x0D) When receiving Functional Execution Command

"nnn" [CR]: Except "000", when it cannot execute commands for any specific reason.

For detail, refer to [7. Error Code Table]

"?" [CR]: When the received data cannot be decoded

8.2 Transfer Example

When setting projector's total dots to 1344 by Expand Command.

PC → PJ: "CF_TDOTS_1344" [CR]

PC ← PJ: "000" [CR] ------ Acceptable

8.3 Operation Requirements

When the projector status is in the status below, Functional Execution Commands are limited

(Status Read Commands are available in following status)

Projector Status	Available Functional Execution Command
In Standby status	C00: POWER ON
Count Down in process	C00: POWER ON (Countdown is terminated)
Cooling Down in process	NONE (No Execution)
Cooling Down in process due to abnormal temperature	NONE (No Execution)
In Abnormal Temperature	NONE (No Execution)
Power Failure (60 seconds after Power failed)	NONE (No Execution)
Power Saving Cooling Down in process	NONE (No Execution)
In Power Saving status	C00: POWER ON C01: POWER OFF

Note) An appropriate error code is returned when the projector receives other command in the

above status.

Page 22

8.4 Image Command

8.4.1 CF CONT Command

Command	"CF_CONT_%1" [CR]
%1	"000-063" Directly specify setting value of Contrast "UP" Increment setting value of Contrast by 1 "DN" Decrement setting value of Contrast by 1
Details	Set user controlled value of Contrast. (Available only in the normal Power ON status) The value set by this command is not stored in the projector. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.) Acceptable "000" [CR]
Response
	Unacceptable	"Error Code" [CR]

8.4.2 CF BRIGHT Command

Command	"CF_BRIGHT_%1" [CR]
%1	"000-063" Directly specify setting value of Brightness "UP" Increment setting value of Brightness by 1 "DN" Decrement setting value of Brightness by 1
Details	Set user controlled value of Brightness. (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.4.3 CF COLOR Command

Command	"CF_COLOR_%	61" [CR]
%1	"000-063" "UP" "DN"	Directly specify setting value of Color Increment setting value of Color by 1 Decrement setting value of Color by 1
Details	Details Set user controlled value of Color. (Available only in the normal Power ON stather the value set by this command is not stored in the projector's memory. There when the power is turned to ALL OFF status, the value returns to the order the setting. (It is stored in Suspend mode.) Acceptable "000" [CR]
Response
Response	Unacceptable	"Error Code" [CR]

8.4.4 CF_TINT Command

Command	"CF_TINT_%1" [CR]
%1	"000-063" Directly specify setting value of Tint "UP" Increment setting value of Tint by 1 "DN" Decrement setting value of Tint by 1
Details	Set user controlled value of Tint (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
. teeponoo	Unacceptable	"Error Code" [CR]

Page 23

8.4.5 CF_COLMNSAV Command

Command	"CF_COLMNSAV_%1" [CR]
%1	"000 – 009" Specify the area to store
Details	Store current setting status of Color Management to the area specified in %1. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

8.4.6 CF COLMNLD Command

Command	"CF_COLMNLD_%1" [CR]
%1	"000 – 009" Specify the area to store
Details	Retrieve Color Management setting status from the area specified in %1. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
1 Coporido	Unacceptable	"Error Code" [CR]

8.4.7 CF APCTRL Command

Command	"CF_APCTRL_%1" [CR]
%1	"L1" "L2" "OFF" " UP" " DN"	Set Auto Picture Control to Level 1. Set Auto Picture Control to Level 2. Set Auto Picture Control OFF. Switch setting forward direction (OFF→L1→L2→OFF) Switch setting backward direction (OFF→L2→L1→OFF)
Details	Set Auto Picture Control (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.) Acceptable "000" [CR]
Response
	Unacceptable	"Error Code" [CR]

8.4.8 CF COLTEMP Command

	Command	"CF_COLTEMP_%1" [CR]
	%1	"000" – "003"
	Details	Set Color Temper The value set by when the power setting. (It is store	rature (Available only in the normal Power ON status) this command is not stored in the projector's memory. Therefore, is turned to ALL OFF status, the value returns to the original ed in Suspend mode.)
	Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 24

8.4.9 CF_WBAL- Command

Command	"CF_WBAL-%1_%2" [CR]
%1	"R" RED "G" GREEN "B" BLUE
%2	"000-063" Directly specify value of Color selected in %1 of White Balance. "UP" Increment setting value of Color specified in %1 of White Balance by 1 "DN" Decrement setting value of Color specified in %1 of White Balance by 1
Details	Set value of Color specified in %1 of White Balance (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.4.10 CF_OFFSET- Command

Command	"CF_OFFSET-%1_%2" [CR]
%1	"R" RED "G" GREEN "B" BLUE
%2	"000-063" Directly specify value of Color selected in %1 of Offset. "UP" Increment setting value of Color specified in %1 of Offset by 1 "DN" Decrement setting value of Color specified in %1 of Offset by 1
Details	Set value of Color specified in %1 of Offset (Available only in the normal Power ON status) The value set by this command will not be stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.) Acceptable "000" [CR]
Response
1 Coporido	Unacceptable	"Error Code"[CR]

8.4.11 CF_SHARP Command

Command	"CF_SHARP_%1" [CR]
%1	"000-031" Directly specify setting value of Sharpness. "UP" Increment setting value of Sharpness by 1 "DN" Decrement setting value of Sharpness by 1
Details	Set user controlled value of Sharpness. (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 25

8.4.12 CF_GAMMA Command

Command	"CF_GAMMA_%1" [CR]
%1	"000-015" Directly specify setting value of Gamma "UP" Increment setting value of Gamma by 1 "DN" Decrement setting value of Gamma by 1
Details	Set user controlled value of Gamma. (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
1.0000100	Unacceptable	"Error Code" [CR]

8.4.13 CF_NZRED Command

Command	"CF_NZRED_%1" [CR]
%1	"ON"Set Noise Reduction to ON "OFF" Set Noise Reduction to OFF
Details	Set or Cancel Noise Reduction. (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Acceptable		"000" [CR]
1.coporido	Unacceptable	"Error Code" [CR]

8.4.14 CF_PROGV Command

Command	"CF_PROGV_%1" [CR]
%1	"ON" Set Progressive scan to ON "FILM" Set Progressive scan to Film mode "OFF" Set Progressive scan to OFF
Details	Set or Cancel Progressive scan. (Valid only when it is in the normal Power ON status.) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.4.15 CF_BCOLOR Command

Command	"CF_BCOLOR_%1" [CR]
%1	"ON" Set BrilliantColor to ON "OFF" Set BrilliantColor to OFF
Details	Set or Cancel BrilliantColor.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 26

8.4.16 CF_IMAGE Command

Command	"CF_IMAGE%1" [CR]
%1	"STAND" Standard (Image adjustment value is set to factory default) "REAL"
Details	Select Image mode. (Valid only when it is in the normal Power ON status.) Parameter "CUSTOM1" to "CUSTOM10" corresponds to "Image1" to "Image10" displayed in projector OSD menu on selecting Image. The value set by this command is stored in EEPROM so that the setting can remain effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.4.17 CF IMAGEADJ Command

Command	"CF_IMAGEADJ_%1"[CR]
%1	"RST" Reset adjusted value for the Image "STR1" Store current adjusted value to Image 1 "STR2" Store current adjusted value to Image 2 "STR3" Store current adjusted value to Image 3 "STR4" Store current adjusted value to Image 4 "STR5" Store current adjusted value to Image 5 "STR6" Store current adjusted value to Image 6 "STR7" Store current adjusted value to Image 7 "STR8" Store current adjusted value to Image 8 "STR9" Store current adjusted value to Image 8 "STR9" Store current adjusted value to Image 9 "STR10" Store current adjusted value to Image 10
Details	Reset or Store adjusted value for Image. (Available only in the normal Power ON status) "STR1"-"STR10" corresponds to "Image1"-"Image10" displayed in projector OSD menu on selecting "Store" for adjusted value of Image. The setting value set in "Image1" to "Image10" is stored and can be retrieved when turning on the projector again after the power is turned to ALL OFF status.
Response Acceptable "000" [CR]		"000" [CR]
Коронос	Unacceptable	"Error Code" [CR]

Page 27

8.5 PC Control Command

8.5.1 CF_FSYNC Command

Command	"CF_FSYNC_%1" [CR]
%1	"0000-0031" Directly specify setting value of Fine Sync "UP" Increment setting value of Fine Sync by 1 "DN" Decrement setting value of Fine Sync by 1
Details	Set value of Fine Sync in PC signal (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

8.5.2 CF TDOTS Command

ſ	Command	"CF_TDOTS_%1" [CR]
	%1	"mmmm – nnnn" Directly specify setting value of Total Dots "mmmm" indicates minimum value, which is current (Display Area H + Position H) value "nnnn" indicates maximum value, that dot clock does not exceed more than 160MHz. "UP" Increment setting value of Total Dots by 1 "DN" Decrement setting value of Total Dots by 1
	Details	Set value of Total Dots in PC signal (Available only in the normal Power ON status). The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
ľ	Response	Acceptable	"000" [CR]
	Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

8.5.3 CF_H-POS Command

Command	"CF_H-POS_%1" [CR]
%1	"0000-nnnn" Directly specify setting value of Horizontal Position "nnn" indicates maximum value, which is current value of (Total Dots – Display Area H) "UP" Increment setting value of Horizontal Position by 1 "DN" Decrement setting value of Horizontal Position by 1
Details	Set value of Horizontal Position in PC signal (Available only in the normal Power ON status) The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

Page 28

8.5.4 CF_V-POS Command

Command	"CF_V-POS_%1" [CR]
%1	"0000-nnnn" Directly specify setting value of Vertical Position "nnnn" indicates maximum value, which is current (Total Line – Display Area V) value "UP" Increment setting value of Vertical Position by 1 "DN" Decrement setting value of Vertical Position by 1
Details	Set Vertical Position value in PC signal (Available only in the normal Power ON status). The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

8.5.5 CF_CLAMP Command

Command	"CF_CLAMP_%1" [CR]
%1	"0000-4095" Directly specify setting value of Clamp "UP" Increment setting value of Clamp by 1 "DN" Decrement setting value of Clamp by 1
Details	Set Clamp value in PC signal. (Available only in the normal Power ON status) The value set by this command will not be stored in the projector's memory. Therefore, when the power is turned to ALL OFF stasis, the value returns to the original setting. (It is stored in Suspend mode.)
	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

8.5.6 CF DDOTS Command

Command	"CF_DDOTS_%1" [CR]
	"0256-nnnn" "nnnn" indicat	Directly specify setting value of Display Dots es maximum value, which is current value of (Total Dots - Position H).
%1	H).In this projector, adds 1 to make the v	the value should be "even number" and if "odd number" is specified, it value even number.
	"UP" Increment setting value of Display Dots by 2 "DN" Decrement setting value of Display Dots by 2
Details	Set Display Dots value in PC signal. (Available only in the normal Power ON status). The value set by this command is not stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

Page 29

8.5.7 CF_DLINE Command

Command	"CF_DLINE_%1" [CR]
%1	"0100-nnnn" Directly specify setting value of Display Line "nnnn" indicates maximum value, which is current value of (Total Line - Position V). "UP" Increment setting value of Display Line by 1 "DN" Decrement setting value of Display line by 1
Details	Set setting value of Display Line in PC signal (Available only in the normal Power ON status). The value set by this command is not being stored in the projector's memory. Therefore, when the power is turned to ALL OFF status, the value returns to the original setting. (It is stored in Suspend mode.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

8.5.8 CF_SETPCADJ Command

Command	"CF_SETPCADJ_%1" [CR]
%1	"XGA1", "HDTV1080", "MODE1"Etc. "EXT11"~"EXT60"
Detail	Note1) When "XGA","HDTV1080","MODE1" is specified in %1, the command is not executed. Note2) When "EXTn-EXTnn" (nn represents number) is specified in %1, "EXT" is displayed in "SYSTEM" menu (only when Network board is provided).
Response	Acceptable	"000" [CR]
	Unacceptable	"101" [CR] When input is Video signal

8.5.9 CF_ORGMODE Command

Command	"CF_ORGMODE_%1" [CR]
	When input signal "VGA1"	is PC Analog; Specify VGA1
%1	"WXGA3"	Specify WXGA3 Specify 1080i60 Specify 10350i Specify 720p60 Specify 720p50 Specify 575p Specify 575i Specify 575i Specify 1080psf/24 Specify 1080psf/25 Specify 1080psf/30 Specify 1080psf/30 Specify 1080p60 al is not PC Analog, error code "101" is returned.
Details	After "EXT n" is set by PC control command such as CF_FSYNC/CF_TDOTS and CF_SETPCADJ command, specify the signal originated with by issuing this command. This command is used to specify projector internal settings such as whether or not to get PC signal through IP (Available only in the normal Power ON status) Note; To differentiate between 60Hz and 50Hz in 1080i and 720p, "60" or "50" is necessary to add to the parameter in this command.
Response	Acceptable	"000" [CR]
	Unacceptable	"101" [CR] When input is Video signal

Page 30

8.5.10 CF_PCSTORE Command

Command	"CF_PCSTORE_%1" [CR]
%1	"MODE 1" Store current PC Adjust status to Mode1 "MODE2" Store current PC Adjust status to Mode2 "MODE3" Store current PC Adjust status to Mode3 "MODE4" Store current PC Adjust status to Mode4 "MODE5" Store current PC Adjust status to Mode5 "MODE6" Store current PC Adjust status to Mode6 "MODE6" Store current PC Adjust status to Mode6 "MODE6" Store current PC Adjust status to Mode6 "MODE8" Store current PC Adjust status to Mode7 "MODE8" Store current PC Adjust status to Mode8 "MODE9" Store current PC Adjust status to Mode8 "MODE10" Store current PC Adjust status to Mode9
Details	Store current value of PC Adjust (each parameter status such as Total dots) to Mode1-10. This command operates the same way as storing to Mode1-10 in PC Adjust Menu. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is except PC analog signal

8.5.11 CF_PCMODEFREE Command

Command	"CF_PCMODEFREE_%1" [CR]
%1	"MODE 1"
Details	Delete the data registered in Custom Mode1–10 and returns it to Free status. This command operates the same way as resetting to Mode1-10 in PC Adjust Menu. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video signal When input is no signal

Page 31

8.6 Input Control Command

8.6.1 CF INPUT Command

Command	"CF_INPUT_%1" [CR]
%1	"1"
Details	Select Input (Only valid when it is in the normal Power ON status.) This command works the same way as "INPUT" button of the projector and remote control.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.6.2 CF_SOURCE Command

Command	"CF_SOURCE_%1" [CR]
%1	"DIGITAL"
Details	Select source of the currently selected Input. (Valid only when in the normal Power ON status.) When selected Input does not meet the requirement for the specified %1, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
1.00001150	Unacceptable	"Error Code" [CR]

8.6.3 CF INPUT1~4 Command

Command	"CF_INPUT%1_%2" [CR]
%1	"1" Specify Input 1 "2" Specify Input 2 "3" Specify Input 3 "4" Specify Input 4
%2	"DIGITAL" Select DVI Input (Computer signal) "ANALOG" Select Analog Input (Computer signal) "VIDEO" Select Composite Video Input "YPBPR" Select S-Video input "YPBPR" Select Y/Pb/Pr Input "YCBCR" Select Y/Cb/Cr Input "SDI1" Select DF-SDI 1 Input "SDI2" Select DF-SDI 2 Input "HDCP" Select HDCP Input "SCART" Select SCART Input "HDMI" Select HDMI Input
Details	Select Input specified by %1, and also Source specified by %2 concurrently. (Valid only when in the normal Power ON status.)
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

Page 32

8.6.4 CF SYSTEM Command

Command	"CF_SYSTEM_%1" [CR]
		"VGA1" Select VGA1
	Input is PC Analog	: "WXGA3"
		"D-XGA1" Select D-XGA1
%1	Input is PC Digital/AV HDCP	: "D-WXGA3" Select D-WXGA3 "D-1080l" Select D-1080i "D-1035l" Select D-1035i "D-720p" Select D-720p "D-575p" Select D-575p "D-480p" Select D-480p "D-1080psf/24" Select D-1080psf/24 "D-1080psf/25" Select D-1080psf/25
		"D-XGA1" Select D-XGA1
	Input is HDMI	: "D-WXGA3" Select D-WXGA3 "D-1080I" Select D-1080i : "D-575p" Select D-575p
		"D-480p" Select D-480p
	Input is Y,Pb/Cb,Pr/Cr	"AUTO" Select System "Auto" "1080P" Select 1080p "1080I" Select 1080i "1035I" Select 1035i : "480P" Select 480p "575I" Select 575i "480I" Select 480i
	Input is Video / S-Video	"AUTO" Select System "Auto" "NTSC" Select NTSC : "PAL-M" Select PAL-M "PAL-N" Select PAL-N
	Input is Dual-SDI	"D-1035I" Select D-1035i "D-1080I" Select D-1080i "D-720P" Select D-720p "D-1080P" Select D-1080p "D-1080PSF/24" Select D-1080psf/24
Details	Select System of (Available only i When selected [CR] is returned	of currently selected Input n the normal Power ON status) input does not include specified %1, error code "101" and it is not executed.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 33

8.7 Screen Control Command

8.7.1 CF_SCREEN Command

Command	"CF_SCREEN_	"CF_SCREEN_%1" [CR]
	Input is PC signal	"NORMAL"
%1	Input is Video signal	"NORMAL"
	Common in AV/PC	"RST" Reset Screen adjustment
Details	Select screen size. (Valid only when in the normal Power ON status.) When selected Input does not meet the requirement for the specified %1, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.7.2 CF_DZCENT Command

Command	"CF_DZCENT_%1" [CR]
%1	"CENT" Cancel Digital Zoom (CENT: "CENTER")
Details	Cancel Digital Zoom mode. (Valid only when in the normal Power ON status and Input for Computer is selected.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"101" [CR] When input is Video

Page 34

8.7.3 CF_KEYSTONE Command

Command	"CF_KEYSTONE _%1" [CR]
%1	"UP" Correct Keystone distortion to reduce upper part of image "FUP" Correct Keystone distortion to reduce upper part "DN" Correct Keystone distortion to reduce lower part of image "FDN" Correct Keystone distortion to reduce lower part largely "LEFT" Correct Keystone distortion to reduce left part of image "FLFT" Correct Keystone distortion to reduce left part of image "FLFT" Correct Keystone distortion to reduce left part largely "RIGHT" Correct Keystone distortion to reduce right part of image "FRGT" Correct Keystone distortion to reduce right part largely "RIGHT" Set Keystone OFF
Details	Change level of Keystone distortion correction (Available only in the normal Power ON status). When reached the limit of the correction level, projector accepts the command but does not execute it. Receiving this command immediately invokes the operation. When trying to set the value beyond available range, error code "201" is returned and the operation is not executed. Example 1: When the correction level of the right part has reached its upper limit and then the command "RIGHT" is received Example 2: When the upper part correction allows only another step, and then the command "FUP" is received.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.7.4 CF_KEYSTONEMODE Command

Command	"CF_KYSTNMODE _%1" [CR]
%1	"STR" Set Keystone store mode to Store "RST" Set Keystone store mode to Reset
Details	Set Keystone store mode (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

8.7.5 CF_CEIL Command

Command	"CF_CEIL_%1" [CR]
%1	"ON" Set Ceiling to ON "OFF" Set Ceiling to OFF
Details	Set/Cancel Ceiling. (Valid only when in the normal Power ON status.) When Ceiling is set to ON, image is left/right as well as top/bottom reversed. The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 35

8.7.6 CF REAR Command

Command	"CF_REAR_%1" [CR]
%1	"ON" Set Rear to ON "OFF" Set Rear to OFF
Details	Set/Cancel Rear. (Valid only when in the normal Power ON status.) When Rear is set to ON, image is left/right reversed. The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.7.7 CF_VSCALE Command

Command	"CF_VSCALE_%1" [CR]
%1	"035
Details	Set Vscale (Available only in the normal Power ON status) When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. When input is no signal, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.7.8 CF_VPOS Command

Command	"CF_VPOS_%1" [CR]
%1	"015" +15 "014" +14 : "001" +1 "000" ±0 " 01" 1 : " 14" 14 " 15" 15 "UP" Increment setting value of Vposition by 1 "DN" Decrement setting value of Vposition by 1
Details	Set V Position (Available only in the normal Power ON status) When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. When input is no signal, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 36

8.7.9 CF_HSCALE Command

Command	"CF_HSCALE_%1" [CR]
%1	"033
Details	Set Hscale (Available only in the normal Power ON status) When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. When input is no signal, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.7.10 CF_HPOS Command

Command	"CF_HPOS_%1" [CR]
%1	"015" +15 "014" +14 : "002" +2 "001" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "000" +1 "02"1 " " 14"14 " 15"15 "UP" Increment setting value of Hposition by 1 "DN" Decrement setting value of Hposition by 1
Details	Set H Position (Available only in the normal Power ON status) When selected screen mode is a setting except Custom, return "101" [CR] and the command is not executed. When input is no signal, return "101" [CR] and the command is not executed.
Response	Acceptable	"000" [CR]
1.coporido	Unacceptable	"Error Code" [CR]

Page 37

8.8 Lamp Command

8.8.1 CF LAMPMODE Command

Command	"CF_LAMPMODE_%1" [CR]
%1	"FULL" Set lamp mode to 2-lamp (FULL) "LAMP1" Set lamp1 mode "LAMP2" Set lamp2 mode
Details	Select Lamp mode. (Valid only when in the normal Power ON status.) The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.8.2 CF_AUTOLAMPCONTRL Command

Command	"CF_AUTOLAMPCONTRL_%1" [CR]
%1	"NORMAL" Set lamp control mode to NORMAL "ECO1" Set lamp control mode to ECO1 "ECO2" Set lamp control mode to ECO2
Details	Select Lamp control mode. (Valid only when in the normal Power ON status.) The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
1.coponoo	Unacceptable	"Error Code" [CR]

8.8.3 CF LAMPLIFECONTRL Command

Command	"CF_LAMPLIFECONTRL_%1" [CR]
%1	"MODE1" Set Lamp life control mode to Mode1 "MODE2" Set Lamp life control mode to Mode2
Details	Select Lamp life control. (Valid only when in the normal Power ON status.) The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.8.4 CF_LAMPINTERVAL Command

Command	"CF_LAMPINTERVAL_%1" [CR]
%1	"AUTO" Set Lamp interval to Auto "0024" Set Lamp interval to 24 hours "0200" Set Lamp interval to 200 hours "0500" Set Lamp interval to 500 hours "1000" Set Lamp interval to 1000 hours "2000" Set Lamp interval to 2000 hours "OFF" Set Lamp interval to OFF
Details	Select Lamp interval. (Valid only when in the normal Power ON status.) The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 38

8.9 Setting Command

8.9.1 CF_LANG Command

Command	"CF_LANG_%1" [CR]
%1	"ENG"
Details	Select language for OSD. (Valid only when in the normal Power ON status.) The language set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.2 CF_MENUPOSITION Command

Command	"CF_MENUPOSITION_%1" [CR]
%1	"UP" Move Menu position to upper side. "DN" Move Menu position to lower side. "LEFT" Move Menu position to left side. "RIGHT" Move Menu position to right side.
Details	Move Menu position. (Valid only when in the normal Power ON status.) This function is worked from the first reception of Command. * When setting beyond the area of movement is carried out, return "101" [CR] and the command is not executed. Ex.1) When movement to right side has already reached limit; and "RIGHT" is received. Ex.2) When "LEFT"/"UP" is received at the default position.
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

8.9.3 CF SIMPLEMENU Command

Command	"CF_SIMPLEMENU_%1" [CR]
%1	"ON" Set Simple menu to On. "OFF" Set Simple menu to Off.
Details	Select Simple menu. (Valid only when in the normal Power ON status.) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Кезропас	Unacceptable	"Error Code" [CR]

Page 39

8.9.4 CF_MENUSIZE Command

Command	"CF_MENUSIZE_%1" [CR]
%1	"NORMAL" Select Menu size to Normal. "DOUBLE" Select Menu size to Double.
Details	Select Menu size. (Valid only when in the normal Power ON status.) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.5 CF_DISP Command

Command	"CF_DISP_%1" [CR]
%1	"ON" Set Display to ON "CNTDWNOFF" Set Display to Count down Off "OFF" Set Display to OFF "UP" Switch forward (On → Count down Off → Off → On →) "DN" Switch backward (On → Off → Count down Off → On →)
Details	Set/Cancel Display. (Valid only when in the normal Power ON status.) The value set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.6 CF_BACKGND Command

Command	"CF_BACKGND_%1" [CR]
%1	"BLUE" Select Blue Back "USER" Select User "BLACK" Select Black Back "UP" Switch forward (Blue Back→User→Black Back→Blue Back) "DN" Switch backward (Blue Back→Black Back→User→Blue Back)
Details	Set Screen status for no signal.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status. *When %1="USER" is received, error code "101" is returned, in the case of Capture non-practice.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.7 CF_PIP Command

Command	"CF_PIP_%1" [CR]
%1	"OFF" "USER1" "USER2" "USER3" "USER4" "USER5"	Select Off Select User1 Select User2 Select User3 Select User4 Select User5
Details	Set "Picture in Picture" status.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 40

8.9.8 CF PIPMODE Command

Command	"CF_PIPMODE_%1" [CR]
%1	"PINP" Select P in P mode "PBYP" Select P by P mode
Details	Set mode of "Picture in Picture". (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.9 CF PIPMAININP Command

Command	"CF_PIPMAINI	"CF_PIPMAININP_%1_%2" [CR]
%1	"1" "2" "3" "4"	Select Input 1 Select Input 2 Select Input 3 Select Input 4
%2	"DIGITAL" "ANALOG" "VIDEO" "S-VIDEO" "YCBCR" "SDI1" "SDI2" "SDI2" "HDCP" "HDMI"	Select DVI Input Select Analog Input Select Composite Video Input Select S-Video input Select Y/Pb/Pr Input Select Y/Cb/Cr Input Select SDI 1 Input Select SDI 2 Input Select SCART Input Select HDCP Input
Details	Select input and source of Main picture of "Picture in Picture". (Valid only when in the normal Power ON status.) * In the case of a specific status, return Error Code "101" [CR] and the command is not executed. When selected Source does not meet the requirement for Input When transmitted command of the input without inserting Board in Input3 or Input4 When selected Input / Source which was impossible of choice by limit of Picture in Picture
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 41

Command	"CF_PIPSUBINP_%1_%2" [CR]
%1	"1" Select Input 1 "2" Select Input 2 "3" Select Input 3 "4" Select Input 4
%2	"DIGITAL" "ANALOG" "VIDEO" "YPBPR" "YCBCR" "SDI1" "SDI2" "SDI2" "HDCP" "HDMI"	Select DVI Input Select Analog Input Select Composite Video Input Select S-Video input Select Y/Pb/Pr Input Select Y/Cb/Cr Input Select SDI 1 Input Select SDI 2 Input Select SCART Input Select HDCP Input
Details	Select input and source of Sub picture of "Picture in Picture". (Valid only when in the normal Power ON status.) * In the case of a specific status, return "101" [CR] and the command is not executed. When selected Source does not meet the requirement for Input When transmitted command of the input without inserting Board in Input3 or Input4 When selected Input / Source which was impossible of choice by limit of "Picture in Picture"
Response	Acceptable	"000" [CR]
1.0000100	Unacceptable	"Error Code" [CR]

8.9.10 CF_PIPSUBINPU Command

8.9.11 CF_PIPSIZE Command

Command	"CF_PIPSIZE_%1_%2" [CR]
%1	"1" "2" "3" "4" "5" "6" "6" "7" "8" "9" "10"	Set main picture size to 10% Set main picture size to 20% Set main picture size to 30% Set main picture size to 40% Set main picture size to 50% Set main picture size to 60% Set main picture size to 70% Set main picture size to 80% Set main picture size to 90% Set main picture size to 100%
%2	"1"
Details	Set display size of "Picture in Picture". (Valid only when in the normal Power ON status.) *When "Picture in Picture" is set to Off, return "101" [CR]
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 42

8.9.12 CF_PIPPOSITION Command

Command	"CF_PIPPOSITION_%1" [CR]
%1	"POS1" Move main picture position to up "POS2" Move main picture position to down "POS3" Move main picture position to left "POS4" Move main picture position to right "POS5" Move main picture position to right "POS6" Move sub picture position to up "POS6" Move sub picture position to down "POS7" Move sub picture position to down "POS8" Move sub picture position to left "POS8" Move sub picture position to left "POS8" Move sub picture position to left
Details	Set position of "Picture in Picture". (Valid only when in the normal Power ON status.) This function is worked from the first reception of Command. * When setting beyond the area of movement is carried out, return Error Code "101" [CR] and the command is not executed. Ex.1) When movement to right side has already reached limit; and "RIGHT" is received. *When "Picture in Picture" is set to Off, return "101" [CR]
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.13 CF PIPFRAMELOCK Command

Command	"CF_PIPFRAMELOCK_%1" [CR]
%1	"MAIN" Set to main picture "SUB" Set to sub picture
Details	Set Frame lock of "Picture in Picture". (Valid only when in the normal Power ON status.)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.14 CF_PIPSTORE Command

Command	"CF_PIPSTORE_%1" [CR]
%1	"USER1" Store current setting status to User 1 "USER2" Store current setting status to User 2 "USER3" Store current setting status to User 3 "USER4" Store current setting status to User 4 "USER5" Store current setting status to User 5
Details	Store setting status of "Picture in Picture". (Valid only when in the normal Power ON status.) This command operates the same way as storing to User1-5 in "Picture in Picture" Menu. The status set by this command is stored in EEPROM and the setting remains even after the power is turned to ALL OFF status.
Response	Acceptable "000" [CR]
	Unacceptable	"Error Code" [CR]

Page 43

8.9.15 CF_PIPMODEFREE Command

Command	"CF_PIPMODEFREE_%1" [CR]
%1	"USER1" Set User1 to Free status "USER 2" Set User2 to Free status "USER 3" Set User3 to Free status "USER 4" Set User4 to Free status "USER 5" Set User5 to Free status
Details	Delete the data registered in Custom User1–5 and returns it to Free status. This command operates the same way as resetting to User1-5 in "Picture in Picture" Menu. (Available only in the normal Power ON status) *When there is only one user mode of stored state, return "101" [CR]
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.16 CF PIPRST Command

Command	"CF_PIPRST_%1" [CR]
%1	"RST" Reset current setting status
Details	Reset current setting status of "Picture in Picture". (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.17 CF_EDGEBLENDING Command

Command	"CF_EDGEBLENDING_%1" [CR]
%1	"ON" Set Edge blending to On "OFF" Set Edge blending to Off
Details	Set Edge blending.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

8.9.18 CF BLEND Command

Command	"CF_BLEND_%1_%2" [CR]
%1	"LEFT" Left side "RIGHT" Right side "TOP" Upper side "BOTTOM" Lower side
%2	"000"-"960" Directly specify value of direction of %1 *Value of upper limit changes by choice of %1 Left 000~960 Right 000~960 Top 000~540 Bottom 000~540
Details	Set value of direction specified by Edge blending %1. (Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Козронзе	Unacceptable	"Error Code" [CR]

Page 44

8.9.19 CF BLENDBLK Command

Command	"CF_BLENDBL	K_%1_%2" [CR]
%1	"R" "G" "B"	Red Green Blue
%2	"-127" ~ "0127"	Directly specify value of color of %1
Details	Set value of color specified by Edge blending %1. (Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.20 CF_BLENDBLKALL Command

Command	"CF_BLENDBLKALL_%1" [CR]
%1	"UP" Increment value of Black level(R/G/B) by 1 "DN" Decrement value of Black level(R/G/B) by 1
Details	Set value of all of Black level of Edge blending. (Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.21 CF BLENDTESTPAT Command

Command	"CF_BLENDTESTPAT_%1" [CR]
%1	"ON" Set to On "OFF" Set to Off
Details	Set Test pattern of Edge blending.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Кезропас	Unacceptable	"Error Code" [CR]

8.9.22 CF_BLENDRST Command

Command	"CF_BLENDRST_%1" [CR]
%1	"RST" Reset current setting status
Details	Reset current setting status of Edge blending. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 45

8.9.23 CF_BLENDMENUOFF Command

Command	"CF_BLENDMENUOFF_%1" [CR]
%1	"SET" Temporarily hide Edge blending menu and edge line "RST" Display Edge blending menu and edge line
Details	Set Menu off function of Edge blending. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.24 CF_BLENDMENU Command

Command	"CF_BLENDMENU_%1" [CR]
%1	"ON" Display Edge blending menu and edge line. "OFF" Set Edge blending menu and edge line undisplayed.
Details	Set Edge blending menu and edge line displayed or undisplayed. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
1.coponoo	Unacceptable	"Error Code" [CR]

8.9.25 CF_COLORMATCHING Command

Command	"CF_COLORMATCHING_%1" [CR]
%1	"ON" Set to On "OFF" Set to Off
Details	Set status of Color matching.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.26 CF_CMMSXY Command

Command	"CF_CMMSXY_	"CF_CMMSXY_%1_%2_%3" [CR]
%1	"RED" "GREEN" "BLUE" "WHITE" "HALFWHITE"	Set value of Red Set value of Green Set value of Blue Set value of White Set value of Half white
%2	"0000" – "1000"	Directly specify "x" value of color of %1
%3	"0000" Directly specify "y" value of color of %1
Details	Set "x","y" value of Measured of Color matching. (Available only in the normal Power ON status) The selectable colors are different by using color wheel. For brightness: Red/Green/Blue/Half white/White For color reproduction: Red/Green/Blue/White When transmit the command of the color that is impossible of choice, return "101" [CR].
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

Page 46

8.9.27 CF_CMMSL Command

Command	"CF_CMMSL_%1_%2" [CR]
%1	"RED" Set value of Red "GREEN" Set value of Green "BLUE" Set value of Blue "WHITE" Set value of White "HALFWHITE" Set value of Half white
%2	"0000" – "1000" Directly specify "L" value of color of %1
Details	Set "L" value of (Available only The selectable For brightness For color repro When transmit [CR].	Measured of Color matching. in the normal Power ON status) colors are different by using color wheel. :: Red/Green/Blue/Half white/White oduction: Red/Green/Blue/White t the command of the color that is impossible of choice, return "101"
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.28 CF_CMTGXY Command

Command	"CF_CMTGXY_%1_%2_%3" [CR]
%1	"RED" Set value of Red "GREEN" Set value of Green "BLUE" Set value of Blue "WHITE" Set value of White "CYAN" Set value of Cyan "MAGENTA" Set value of Magenta "YELLOW" Set value of Yellow
%2	"0000" – "1000" Directly specify "x" value of color of %1
%3	"0000" Directly specify "y" value of color of %1
Details	Set "x","y" value of Target of Color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.29 CF CMTGG Command

Command	"CF_CMTGG_%1_%2" [CR]
%1	"RED" Set value of Red "GREEN" Set value of Green "BLUE" Set value of Blue "WHITE" Set value of White "CYAN" Set value of Cyan "MAGENTA" Set value of Magenta "YELLOW" Set value of Yellow
%2	"0000" – "1000" Directly specify "g" value of color of %1
Details	Set "g" value of Target of Color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 47

8.9.30 CF_CMAUTOTESTPAT Command

Command	"CF_CMAUTOTESTPAT_%1" [CR]
%1	"ON" Set to On "OFF" Set to Off
Details	Set Auto test pattern of Color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.31 CF_CMRST Command

Command	"CF_CMRST_%1" [CR]
%1	"CMRST" Reset setting of Color matching "ADCRST" Reset setting of Advanced color matching
Details	Reset setting of Color matching.(Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.32 CF_CMSTORE Command

Command	"CF_CMSTORE_%1" [CR]
%1	"CMSTR" Store setting of Color matching "ADCSTR" Store setting of Advanced color matching
Details	Store setting of Color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.33 CF_CMMSTESTPAT Command

Command	"CF_CMMSTESTPAT_%1" [CR]
%1	"RED" Display Red "GREEN" Display Green "BLUE" Display Blue "WHITE" Display White "HALFWHITE" Display Half white "OFF" Do not show test pattern display
Details	Display Test pattern of Measured of Color matching. (Available only in the normal Power ON status) The selectable colors are different by using Color wheel. For brightness: Red/Green/Blue/Half white/White For color reproduction: Red/Green/Blue/White When transmit the command of the color that is impossible of choice, return "101" [CR].
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 48

8.9.34 CF_CMTGTESTPAT Command

Command	"CF_CMTGTESTPAT_%1" [CR]
%1	"RED" Display Red "GREEN" Display Green "BLUE" Display Blue "WHITE" Display White "CYAN" Display Cyan "MAGENTA" Display Magenta "YELLOW" Display Yellow "OFF" Do not show test pattern display
Details	Display Test pattern of Target of Color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
1.coponoo	Unacceptable	"Error Code" [CR]

8.9.35 CF_CMFDEFAULT Command

Command	"CF_CMFDEFAULT_%1" [CR]
%1	"RST" Reset the value of Target
Details	Return the value of Advanced color matching to Factory Default status (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.36 CF CMMENUOFF Command

Command	"CF_CMMENUOFF_%1" [CR]
%1	"SET" Temporarily hide Advanced color matching menu "RST" Display Advanced color matching menu
Details	Set Menu off function of Advanced color matching. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.37 CF_CMMENU Command

Command	"CF_CMMENU_%1" [CR]
%1	"ON" Display Advanced color matching menu "OFF" Set Advanced color matching menu undisplayed.
Details	Set Advanced color matching menu displayed or undisplayed. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
reopense	Unacceptable	"Error Code" [CR]

Page 49

8.9.38 CF DYNAMICBLACK Command

Command	"CF_DYNAMICBLACK_%1" [CR]
%1	"OFF" "LOW" "HIGH"	Set to Off Set to Low Set to High
Details	Set status of DynamicBlack.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable "000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.39 CF_HDMISETUP Command

Command	"CF_HDMISETUP_%1" [CR]
%1	"NORMAL" Set to Normal "ENHANCED" Set to Enhanced
Details	Set status of HDMI setup.(Available only in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Пезропзе	Unacceptable	"Error Code" [CR]

8.9.40 CF_LOGO Command

Command	"CF_LOGO_%1_%2" [CR]
%1	"0000 – 9999" Directly set Logo PIN code
%2	"OFF"Cancel Logo display "DFLT"Cancel Logo of Factory Default "USER"Select User "UP"Select functions to choose forward (OFF → DFLT → USER → OFF →) "DN"Select functions to choose backward (OFF → USER → DFLT → OFF →)
Details Set Logo mode.(Available only in the normal Power ON status The status set by this command is stored in EEPROM effective even after the power is turned to ALL OFF status. Set Logo PIN code in %1. *When Logo Lock is enabled: PIN code is matched PIN code is mismatched PIN code is beyond %1 available range Command is invalid PIN code is beyond %1 available range		e. (Available only in the normal Power ON status) t by this command is stored in EEPROM and setting remains after the power is turned to ALL OFF status. code in %1. ock is enabled: natched Command is valid (Acceptable) nismatched Command is invalid (Error code "102") beyond %1 available range Command is invalid (Error ock is disabled:
	PIN code is v PIN code is c	vithin %1 available range Command is valid (Acceptable) out of %1 available range Command is invalid (Error code "?")
	Note: When Logo Lock is enabled, matching Logo PIN code switches Logo but Logo Lock is not cancelled (Lock status is kept).
	*When %2="USER" is received, error code "101" is returned, in the case of Capture non-practice.
Response	Acceptable	"000" [CR]
Rooponde	Unacceptable	"Error Code" [CR]

Page 50

8.9.41 CF_FANSPEED Command

Command	"CF_FANSPEED_%1" [CR]
%1	"MAX" Select Maximum speed of Fan Control "NOR" Select Normal speed of Fan Control
Details	Switch Fan Control Speed. (Valid only when in the normal Power ON status.) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.42 CF_RCODE Command

Command	"CF_RCODE_%1" [CR]
%1	"001"
Details	Select Remote Control Code (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.43 CF RSENS Command

Command	"CF_RSENS_%	"CF_RSENS_%1" [CR]
%1	"ALL" Select all receiver of projector "FRONTTOP" Select both front and top receiver of projector "BACKTOP" Select both back and top receiver of projector "FRONTBACK" Select both front and back receiver of projector "FRONT" Select only front receiver of projector "TOP" Select only top receiver of projector "BACK" Select only back receiver of projector "BACK" Select only back receiver of projector "BACK" Select only back receiver of projector "BACK" Select only back receiver of projector "DN" Switch forward (ALL → FRONTTOP → BACK→ALL) "DN" Switch backward (BACK → TOP → FRONT→FRONTBACK→ BACKTOP → FRONTTOP → ALL→BACK)
Details	Select location of infrared remote receiver of remote control (Available only in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 51

8.9.44 CF_P-MANE Command

Command	"CF_P-MANE_%1" [CR]
%1	"OFF" Set Power Management to Off "READY" Set Power Management to Ready "SHUTDOWN" Set Power Management to Shut Down mode "UP" Switch forward (Off→Ready→Shut down→Off) "DN" Switch backward (Off→Shut down→Ready→Off)
Details	Set/Cancel Power Management. (Valid only when in the normal Power ON status.) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable "000" [CR]
Ксэронае	Unacceptable	"Error Code" [CR]

8.9.45 CF_P-MANETIME Command

Command	"CF_P-MANETIME_%1" [CR]
%1	"01" - "30" Directly specify setting time by the minute "UP" Increment value by 1 (Switched in 01→02→ → 30 → 01 order) "DN" Decrement value by 1 (Switched in 30→29→ → 01 → 30 order)
Details	Set time of Power Management time (Available only in the normal Power ON status). The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable "000" [CR]
Ксэронас	Unacceptable	"Error Code" [CR]

8.9.46 CF ON-STA Command

Command	"CF_ON-STA_%1" [CR]
%1	"ON" Set Power On Start to ON. "OFF" Set Power On Start to OFF. "UP" Toggle between ON and OFF.(On→Off→On →) "DN" Toggle between ON and OFF.(On→Off→On →) *"UP" and "DN" are exactly same operation.
Details	Set/Cancel Power ON Start (Only valid when it is in the normal Power ON status) The status set by this command is stored in EEPROM and the setting remains effective after the power is turned to ALL OFF status.
Response	Acceptable "000" [CR]
1 Coporise	Unacceptable	"Error Code" [CR]

Page 52

8.9.47 CF_PJPINCODE Command

Command	"CF_PJPINCODE_%1" [CR]
%1	"0000 – 9999" Directly specify PJ PIN code
Details	Enter PIN code status) PIN code can r When PIN code PIN code is n PIN code is n PIN code is t When PIN code PIN code is v PIN code is c This command code after Pow When PIN code projector is turr	e to cancel PIN code lock (Available only in the normal Power ON not be changed. (Only PIN code lock is canceled.) de Lock is enabled: natched Command is valid (Acceptable) nismatched Command is invalid (Error code "102") de lock is canceled: within %1 range Command is valid (Acceptable) but of %1 range Command is valid (Acceptable) but of %1 range Command is valid (Acceptable) but of %1 range Command is invalid (Error code is 102) is only valid when "PJ PIN code" dialog is displayed to enter PIN er is ON and Countdown is completed. e lock is set to "On1", it needs to send this command every time the hed on.
Response	Acceptable "000" [CR]
1.coponoo	Unacceptable	"Error Code" [CR]

8.9.48 CF FILH Command

Command	"CF_FILH_%1" [CR]
%1	"RST" Reset Filter used time
Details	Reset used time for filter of projector
Response	Acceptable "000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.49 CF FILTIMER Command

Command	"CF_FILTIMER_%1" [CR]
%1	"1000" Set 1000 hours "2000" Set 2000 hours "3000" Set 3000 hours "OFF" Set Off(Do not warning display)
Details	Set time to display Filter cleaning / replacement warning on screen
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.50 CF FILCTL Command

Command	"CF_FILCTL_%1" [CR]
%1	"ROLL" Execute operation of scroll of filter
Details	Execute operation of scroll of filter
Dooponoo	Acceptable	Acceptable
Response	Unacceptable	Unacceptable

Page 53

8.9.51 CF_FILSCRL Command

Command	"CF_FILSCRL_%1" [CR]
%1	"RST" Reset Filter scroll counter
Details	Reset Filter scroll counter
Posponso	Acceptable	Acceptable
Response	Unacceptable	Unacceptable

8.9.52 CF TESTPAT Command

Command	"CF_TESTPAT_%1" [CR]
%1	"COLOR" "GRAD1" "GRAD2" "GRAD4" "WHITE" "BLACK" "CROSS" "OFF" "UP" "DN"	Display Color bar Display 16step(white→black) Display 16step(white→black) Display 16step(white↓black) Display 16step(white↑black) Display all white Display all black Display Cross Do not show test pattern display Switch forward Switch backward
Details	Execute test pattern display.(Available only in the normal Power ON status)
Response	Acceptable "000" [CR]
Responde	Unacceptable	"Error Code" [CR]

8.9.53 CF FDEFAULT Command

Command	"CF_FDEFAULT_%1" [CR]
%1	"RST"
Details	Return the sett (Valid only whe	ings to Factory Default status n in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.54 CF_KEYDIS Command

Command	"CF_KEYDIS_%1" [CR]
%1	"NONE" RC & KEY are valid "RC" RC is invalid "KEY" KEY is invalid
Details	Set the limitation of RC/KEY use (Valid only when in the normal Power ON status)
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

Page 54

8.9.55 CF SHUTRCPROT Command

Command	"CF_SHUTRCPROT_%1" [CR]
%1	"ON" Disable RC key from controlling Shutter (Protection On) "OFF" Enable RC key to control Shutter (Protection Off)
Details	Set valid / invalid of RC use on Shutter control function (Valid only when in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.56 CF SHUTKEYPROT Command

Command	"CF_SHUTKEYPROT_%1" [CR]
%1	"ON" Disable key on the side panel from controlling Shutter (Protection On) "OFF" Enable key on the side panel to control Shutter (Protection Off)
Details	Set valid / invalid use of key on the side panel on Shutter control function. (Valid only when in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.57 CF_SHUTH Command

Command	"CF_SHUTH_%1" [CR]
%1	"005"-"480"Specify setting time directly "UP"Add 1 minute "DN"Decrease 1 minute
Details	Set time of operating shutter management function. (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
1 Coponioo	Unacceptable	"Error Code" [CR]

8.9.58 CF SHUTEFFECT Command

Command	"CF_SHUTEFFECT_%1" [CR]
%1	"OFF"Disable fade in and out function of Shutter "L1" Set fade in and out function of Shutter to L1 "L2" Set fade in and out function of Shutter to L2
Details	Set Effect funct When L1 is sel- When L2 is sel- The status se effective even a	tion of Shutter. (Valid only when in the normal Power ON status) ected, projected image quickly fade in and out. ected, projected image slowly fade in and out. t by this command is stored in EEPROM and setting remains after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
response	Unacceptable	"Error Code" [CR]

Page 55

8.9.59 CF_SHUTRELEASE Command

Command	"CF_SHUTRELEASE_%1" [CR]
%1	"ANY"Enable to release Shutter with any key "SHUTTER"Enable to release Shutter with only "SHUTTER" key
Details	Set Release key of Shutter. (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
10000000	Unacceptable	"Error Code" [CR]

8.9.60 CF_DELAYCTRL Command

Command	"CF_DELAYCTRL_%1" [CR]
%1	"OFF" Set Video delay control to OFF "LOW" Set Video delay control to LOW "MID" Set Video delay control to MID "HIGH" Set Video delay control to HIGH
Details	Select the mode of Video delay control (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
1.coporido	Unacceptable	"Error Code" [CR]

8.9.61 CF_CCAPTIONDISP Command

Command	"CF_CCAPTIONDISP_%1" [CR]
%1	"OFF" Select Off "CC1" Select CC1 "CC2" Select CC2 "CC3" Select CC3 "CC4" Select CC4
Details	Select channel of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status. Note)Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed to NTSC.
Response	Acceptable	"000" [CR]
reception	Unacceptable	"Error Code" [CR]

Page 56

8.9.62 CF_CCAPTIONCOLOR Command

Command	"CF_CCAPTIONCOLOR _%1" [CR]
%1	"COLOR" Select Color "WHITE" Select White
Details	Select color of Closed caption. The status set with this command is stored in EEPROM and its setting is effective even after ALL is OFF. This command is available in normal Power ON status. Note)Closed caption is available under conditions below; Entered signal is appropriate (Video, NTSC signal of S-video) and System is fixed to NTSC.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.63 CF_FRAMELOCK Command

Command	"CF_FRAMELOCK_%1" [CR]
%1	"AUTO" Set Frame lock function to Auto. "23.98" Set Frame lock to "Manual, 23.98 Hz." "25.00" Set Frame lock to "Manual, 25.00 Hz." "29.97" Set Frame lock to "Manual, 29.97 Hz." "30.00" Set Frame lock to "Manual, 30.00 Hz." "50.00" Set Frame lock to "Manual, 50.00 Hz." "59.94" Set Frame lock to "Manual, 59.94 Hz." "60.00" Set Frame lock to "Manual, 60.00 Hz."
Details	Set Frame lock function to Auto or Manual. (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
	Unacceptable	"Error Code" [CR]

8.9.64 CF FRAMELOCKADJ Command

Command	"CF_FRAMELOCKADJ_%1" [CR]
%1	"UP" Search frame lock frequency upward. "DN" Search frame lock frequency downward.
Details	Search Frame lock frequency and set manually. (Valid only when in the normal Power ON status)
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.9.65 CF_FRAMELOCKRST Command

Command	"CF_FRAMELOCKRST_%1" [CR]
%1	"RST" Reset Frame lock frequency
Details	Reset the setting of Frame lock. (Valid only when in the normal Power ON status) The status set by this command is stored in EEPROM and setting remains effective even after the power is turned to ALL OFF status.
Response	Acceptable	"000" [CR]
1 coporido	Unacceptable	"Error Code" [CR]

Page 57

8.10 Other Command

8.10.1 CF KEYEMU Command

Command	"CF_KEYEMU	_%1" [CR]
%1	"RIGHT" Move Pointer rightward in On-Screen Display Menu "LEFT" Move Pointer leftward in On-Screen Display Menu "UP" Move Pointer to upward On-Screen Display Menu "DN" Move Pointer to downward in On-Screen Display Menu "SELECT" The same operation as "SELECT" button of RC "AUTOPC" Execute Auto PC Adj. operation "LENSSHIFT"
Details	The same oper Auto PC Adj. of this Auto PC Ad When transmi - When User User menu. - When Use non-practice "101" is not cursor moves t example: Display main m Move a cursor a cursor doesn *When transmi - When pract returned. - When pract returned.	ration as Control Key. operation is not stopped before getting back a return value during dj. operation even if this command is received again. t command of CF_KEYEMU parameter r menu is displayed: function is carried out with having displayed or menu isn't displayed: error code "101" is returned, function is returned even if a command of CF_KEYEMU is transmitted when o the item which cannot toggle at an edge of the main menu. henu, and move to second menu of Image adj. to "Quit" position, and transmit a command of KEYEMU_DN. Then 't toggle and "000" is returned. t command of CF_KEYEMU AUTOPC ctice of Auto pc adj is possible: Function is practice, "000" is tice of Auto pc adj is impossible: display exclamation mark, "000" is
Posponso	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.10.2 CF_MENU Command

Command	"CF_MENU_%1" [CR]
%1	"ON" Display On-Screen Display Menu "OFF" Hide On-Screen Display Menu
Details	Set On-Screen Display mode. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
Кезропае	Unacceptable	"Error Code" [CR]

Page 58

8.10.3 CF_POWER Command

Command	"CF_POWER_%1" [CR]
%1	"ON" Power ON "OFF" Power OFF * Issuing another command during countdown process forced countdown operation to be terminated. * Error Code is returned in some projector statuses, which indicates the command is impossible to be executed. (See [8.3] for details) * Returning the response "000" [CR] (acceptable) does not always mean that the status has already changed to Power ON. Example: When the temperature approaches abnormal status after returning "000" [CR] to the command CF_POWER ON. Therefore, to get the projector status requires using Status Read command.
Details	Set Power to ON/OFF
Response	Acceptable	Acceptable "000" [CR]
	Unacceptable	"Error Code" [CR]

8.10.4 CF FREEZE Command

Command	"CF_FREEZE_%1" [CR]
%1	"ON" Set Freeze to ON. "OFF" Set Freeze to OFF. "UP" Switch forward (On→Off→On→) "DN" Switch backward (On→Off→On→) * The same operation for "UP" and "DN" as this model has only "ON" / "OFF".
Details	Set / Cancel Freeze function. (Available only in the normal Power ON status) Receiving FREEZE_ON command when the projector is Freeze enabled, Freeze status is kept.
Response	Acceptable	"000" [CR]
Response	Unacceptable	"Error Code" [CR]

8.10.5 CF_VMUTE Command

Command	"CF_VMUTE_%1" [CR]
%1	"ON" Set Video Mute to ON (Shutter Close). "OFF" Set Video Mute to OFF (Shutter Open).
Details	ON / OFF Video Mute function. (Available only in the normal Power ON status)
Response	Acceptable	"000" [CR]
1.0000100	Unacceptable	"Error Code" [CR]

Page 59

9. Status Read Command

9.1 Format

1) PC issues a command in the format below:

Command: String

2) When the projector receives the applicable command, it returns the required information

as a data string.

"000 "%1 [CR]

%1: required Information (a data string. Refer to [Basic Status Read Command Table])

3) When the received data cannot be decoded, the projector returns "?" [CR]

9.2 Transfer Example

Getting total dots of the projector by Expand Serial Commands

PC → PJ: "CR_TDOTS" [CR] PC ← PJ: "000 1344" [CR]

9.3 Operation condition

Basically it should be always operated.

Page 60

9.4 Image Status Read Commands

9.4.1 CR CONT Command

Command	"CR_CONT" [CR]
Details	Get user controlled value of Contrast
Response	Acceptable	"000_%1" [CR]
	%1	"000" – "063"
	Unacceptable	"?" [CR]

9.4.2 CR BRIGHT Command


Command	"CR_BRIGHT" [CR]
Details	Get user controlled value of Brightness
	Acceptable	"000_%1" [CR]
Response	%1	"000" – "063"
	Unacceptable	"?" [CR]

9.4.3 CR_COLOR Command

Command	"CR_COLOR" [CR]
Details	Get user controlled value of Color
Response	Acceptable	"000_%1" [CR]
	%1	"000" – "063"
	Unacceptable	"Error Code" [CR]When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.4.4 CR_TINT Command

Command	"CR_TINT" CR]
Details	Get user controlled value of Tint
	Acceptable	"000_%1" [CR]
Boononoo	%1	"000" – "063"
Response	Unacceptable	"Error Code" [CR]When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.4.5 CR_APCTRL Command

Command	"CR_APCTRL" [CR]
Details	Get setting status of Auto Picture Control
	Acceptable	"000_%1" [CR]
Response	%1	"L1" Operate Auto Picture Control with Level1 "L2" Operate Auto Picture Control with Level2 "OFF" Set Auto Picture Control OFF
	Unacceptable	"?" [CR]

Page 61

9.4.6 CR COLTEMP Command

Command	"CR_COLTEMP" [CR]
Details	Get Color Temperature setting status
Response	Acceptable	"000_%1" [CR]
	%1	"000" ~"003" "BLANK" OSD Menu is blank (Neither of Xlow / Low / Mid / High)
	Unacceptable	"?" [CR]

9.4.7 CR_WBAL-R Command

Command	"CR_WBAL-R" [CR]
Details	Get user controlled Red value of White Balance
	Acceptable	"000_%1" [CR]
Response	%1	"000" – "063"
Response	Unacceptable	"?" [CR]

9.4.8 CR_WBAL-G Command

Command	"CR_WBAL-G" [CR]
Details	Get user controlled Green value of White Balance
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	"000" – "063"
	Unacceptable	"?" [CR]

9.4.9 CR WBAL-B Command

Command	"CR_WBAL-B" [CR]
Details	Get user controlled Blue value of White Balance
	Acceptable "000_%1" [CR]
Response	%1	"000" – "063"
	Unacceptable	"?" [CR]

9.4.10 CR OFFSET-R Command

Command	"CR_OFFSET-R" [CR]
Details	Get user controlled Red value of Offset
Response	Acceptable	"000_%1" [CR]
	%1	"000" – "063"
	Unacceptable	"?" [CR]

9.4.11 CR_OFFSET-G Command

Command	"CR_OFFSET-G" [CR]
Details	Get user controlled Green value of Offset
	Acceptable	"000_%1" [CR]
Response	%1	"000" – "063"
Response	Unacceptable	"?" [CR]

Page 62

9.4.12 CR_OFFSET-B Command

Command	"CR_OFFSET-B" [CR]
Details	Get user controlled Blue value of Offset
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	"000" – "063"
Response	Unacceptable	"?" [CR]

9.4.13 CR_SHARP Command

Command	"CR_SHARP" [CR]
Details	Get user controlled value of Sharpness
	Acceptable	"000_%1" [CR]
Response	%1	"000" – "031"
Response	Unacceptable	"?" [CR]

9.4.14 CR_GAMMA Command

Command	"CR_GAMMA"	"CR_GAMMA" [CR]
Details	Get user contro	Get user controlled value of Gamma
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	"000" – "015"
	Unacceptable	"?" [CR]

9.4.15 CR NZRED Command

Command	"CR_NZRED" [CR]
Details	Get Noise Reduction setting status
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Noise Reduction is ON "OFF" Noise Reduction is OFF
	Unacceptable	"Error Code" [CR]When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.4.16 CR_PROGV Command

Command	"CR_PROGV" [CR]
Details	Get Progressive scan setting status
	Acceptable	"000_%1" [CR]
Response	%1	"ON" Set Progressive scan On "FILM" Select FILM mode "OFF" Set Progressive scan Off
Response	Unacceptable	"Error Code" [CR]When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

Page 63

9.4.17 CR_BCOLOR Command

Command	"CR_PROGV" [CR]
Details	Get BrilliantColor setting status
	Acceptable "000_%1" [CR]
Response	%1	"ON" Set BrilliantColor to On "OFF" Set BrilliantColor to Off
Response	Unacceptable	"Error Code" [CR]When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.4.18 CR_IMAGE Command

Command	"CR_IMAGE" [CR]
Details	Get image setting status. The Required data "CUSTOM1" – "CUSTOM10" corresponds to "Image1" – "Image10" displayed when selecting Image on OSD Menu.
	Acceptable	"000_%1" [CR]
Response	%1	"STAND"
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.4.19 CR IMGGMD Command

Command	"CR_IMGGMD" [CR]
Details	Get setting status of Standard/Real/Cinema/Dynamic in Image Gamma
	Acceptable	"000_%1" [CR]
Response	%1	"STD" Standard "REL" Real "CNM" Cinema "DYN" Dynamic
	Unacceptable	"?" [CR]

Page 64

9.5 PC Status Read Commands

9.5.1 CR FSYNC Command

Command	"CR_FSYNC" [CR]
Details	Get value of Fine Sync
Response	Acceptable	"000_%1" [CR]
Кезронзе	%1	"0000" – "0031"
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.5.2 CR_TDOTS Command

Command	"CR_TDOTS" [CR]
Details	Get value of To	Get value of Total Dots
Response	Acceptable	"000_%1" [CR]
	%1	"mmmm" – "nnnn" (mmmm = Display area H + Position H) (nnnn = Maximum value less than 160 MHz of Dot Clock)
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.5.3 CR H-POS Command

Command	"CR_H-POS" [CR]
Details	Get value of Horizontal Position
Response	Acceptable	"000_%1" [CR]
	%1	"0000" – " nnnn" (nnnn = Total Dots - Display Area H)
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.5.4 CR_V-POS Command

Command	"CR_V-POS" [CR]
Details	Get value of Ve	Get value of Vertical Position
	Acceptable	"000_%1" [CR]
Response	%1	"0000" – " nnnn" (nnnn = Total Line - Display Area V)
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

Page 65

9.5.5 CR CLAMP Command

Command	"CR_CLAMP" [CR]
Details	Get value of Clamp
Response	Acceptable	"000_%1" [CR]
	%1	"0000" – " 4095"
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.5.6 CR_DDOTS Command

Command	"CR_DDOTS" [CR]
Details	Get value of Display Dots
	Acceptable	"000_%1" [CR]
Response	%1	"0256"-"nnnn" (nnnn = Total Dots – Position H)
Response	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.5.7 CR_DLINE Command

Command	"CR_DLINE" [CR]
Details	Get value of Dis	Get value of Display Line
Response	Acceptable	"000_%1" [CR]
	%1	"0100" – " nnnn" (nnnn = Total Line – Position V)
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

Page 66

9.5.8 CR_SETPCADJ Command

Command	"CR_SETPCADJ" [CR]
Details	Get PC signal for current system
	Acceptable	"000_%1" [CR]
Response	s Get PC signal f Acceptable	When input signal is PC Analog; "VGA1"
	Unacceptable	\| "?" [CK]

Page 67

9.5.9 CR_ORGMODE Command

Command	"CR_ORGMOE	DE" [CR]
Details	Get the origina When MODE1	Get the original signal of current selected Mode that is set in PC Adj. When MODE1- 10 or EXT11-60 is not selected, get the current signal.
	Acceptable	"000_%1" [CR]
Response	%1 Unacceptable	When input signal is PC Analog; "VGA1"
	Chaooptable

9.5.10 CR_PCSTORE Command

Command	"CR_PCSTORE" [CR]
Details	Get Free or Stored status of MODE1 - 5 in PC Adjust. Data consists of 10 bytes and each byte represents MODE1-10.(F:Free, S:Stored)
	Acceptable	"000_%1" [CR]
Response	%1	"FFFFFFFFF" ALL Free "SFFFFFFFF" Mode1 is Stored, others are Free : "FFFFFFFFS" Mode10 is Stored, others are Free "SSSSSSSSS" ALL Stored
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

Page 68

9.6 Video Status Read Command

9.6.1 CR SERSYS Command

Command	"CR_SERSYS" [CR]
Details	Get currently s Value only whe	Get currently selected signal. Value only when Input is video. (Invalid when Input is computer)
	Acceptable	"000_%1" [CR]
Response	%1	"1080PSF/24" 1080psf 24Hz "1080P60" 1080p 60Hz "1080P50" 1080p 50Hz "1080P30" 1080p 30Hz "1080P25" 1080p 24Hz "1080P24" 1080i 60Hz / 1080psf 30Hz "1080I60" 1080i 50Hz / 1080psf 25Hz "1080I50" 1035i "720P60"
	Unacceptable	"?" [CR]

Page 69

9.7 Input Read Command

9.7.1 CR INPUT Command

Command	"CR_INPUT" [CR]
Details	Get selected INPUT No.
	Acceptable	"000_%1" [CR]
Response	%1	"1" – "4"
	Unacceptable	"?" [CR]

9.7.2 CR_SOURCE Command

Command	"CR_SOURCE" [CR]
Details	Get selected S	Get selected Source
	Acceptable	"000_%1" [CR]
Response	%1	"DIGITAL"
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

Page 70

9.7.3 CR_SYSTEM Command

Command	"CR_SYSTEM" [CR]
Details	Get selected System
Response	Acceptable		"000_%1" [CR]
	%1	Input is PC Analog	"VGA1"
		Input is PC-Digital/ AV-HDCP	"D-XGA1" indicates D-XGA1 is selected "D-WXGA3" indicates D-WXGA3 is selected "D-1080I" indicates D-1080i is selected "D-1035I" indicates D-1035i is selected "D-720P" indicates D-720p is selected "D-720P" indicates D-575p is selected "D-780PSF/24" indicates D-480p is selected "D-1080PSF/24" indicates D-1080psf/24 is selected "D-1080PSF/25"indicates D-1080psf/25 is selected "D-1080PSF/30"indicates D-1080psf/30 is selected "D-1080PSF/30"indicates D-1080psf/30 is selected
		Input is HDMI	"D-XGA1" indicates D-XGA1 is selected : "D-WXGA3" indicates D-WXGA3 is selected "D-1080I" indicates D-1080i is selected "D-1035I" indicates D-1035i is selected "D-720P" indicates D-720p is selected "D-757P" indicates D-575p is selected "D-480P" indicates D-480p is selected * Error Code "101" [CR] is returned for no signal
		Input is Y,Pb/Cb,Pr/Cr	"AUTO" indicates Auto is selected "1080P" indicates 1080p is selected "1080I" indicates 1080i60Hz is selected "1035I" indicates 1035i is selected "720P" indicates 720p is selected "575P" indicates 575p is selected "480P" indicates 575p is selected "575I" indicates 575i is selected "480I" indicates 480p is selected "480I"

Page 71

		Input is Video or S-video	"AUTO" indicates Auto is selected "NTSC" indicates NTSC is selected "NTSC443" indicates NTSC4.43 is selected "PAL" indicates PAL is selected "SECAM" indicates SECAM is selected "PAL-N" indicates PAL-M is selected "PAL-N" indicates PAL-N is selected " Selected System is returned, whether or not signal is coming.
		Input is Dual-SDI	"D-1035I" indicates D-1035i is selected "D-1080I" indicates D-1080i is selected "D-720P" indicates D-720p is selected "D-1080P" indicates D-1080p is selected "D-1080PSF/24" indicates D-1080psf/24 is selected "D-1080I" indicates D-1080p is selected * Error Code "101" [CR] is returned for no signal
	Ur	nacceptable	"Error Code" [CR]

9.7.4 CR_ SYSLIST Command

Command	"CR_SYSLIST	" [CR]
Details	Get possible sy	Get possible systems for System list
	Acceptable	"000_%1_%2%x" [CR]
Response	%1	Error Code "101" is returned for no signal. Otherwise following values are returned according to Source. When input is PC-Analog; "XGA1"

Page 72

9.7.5 CR_MODELIST Command

Command	"CR_MODELIST" [CR]
Details	Get possible m	odes for Mode list
	Acceptable	"000_%1_%2%x" [CR]
Response	%1	Error Code "101" is returned except for PC-Analog and for no signal with PC-Analog Possible modes in Mode1-10 are returned when PC-Analog signal is coming. "MODE1" "MODE2" "MODE3" " "MODE8" "MODE8" "MODE9"
	Unacceptable	"Error Code" [CR]

9.7.6 CR_SRCINP1 Command

Command	"CR_SRCINP1" [CR]
Details	Get Source of	Input1
	Acceptable	"000_%1" [CR]
Response	%1	"DIGITAL"
	Unacceptable	"?" [CR]

9.7.7 CR_SRCINP2 Command

Command	"CR_SRCINP2" [CR]
Details	Get Source of Input 2
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	The same data as CF_SRCINP1
	Unacceptable	"?" [CR]

9.7.8 CR_SRCINP3 Command

Command	"CR_SRCINP3" [CR]
Details	Get Source of Input 3
	Acceptable	"000_%1" [CR]
Response	%1	The same data as CF_SRCINP1
Response	Unacceptable	"?" [CR]

Page 73

9.7.9 CR_SRCINP4 Command

Command	"CR_SRCINP3" [CR]
Details	Get Source of Input 4
	Acceptable	"000_%1" [CR]
Response	%1	The same data as CF_SRCINP1
Response	Unacceptable	"?" [CR]

9.7.10 CR_HMSLOT Command

Command	"CR_HMSLOT" [CR]
Details	Get the total number of Slots(Inputs)
	Acceptable	"000_%1" [CR]
Response	%1	"004"
Response	Unacceptable	"?" [CR]

9.7.11 CR_NMSLOT1 Command

Command	"CR_NMSLOT1" [CR]
Details	Get the board name inserted to Slot1
	Acceptable	"000_%1" [CR]
Response	%1	"RGB-HDMI" Input1/ New RGB&HDMI board "5BNC-VIDEO" Input2/ New Video board "HDCP-DVI2" New HDCP & DVI Card "DUAL-SDI" HD&SD-SDI board "NOTERMINAL" There is no board inserted
	Unacceptable	"?" [CR]

9.7.12 CR_NMSLOT2 Command

Command	"CR_NMSLOT2" [CR]
Details	Get the board name inserted to Slot 2
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	The same data as CR_NMSLOT1
Response	Unacceptable	"?" [CR]

9.7.13 CR_NMSLOT3 Command

Command	"CR_NMSLOT3" [CR]
Details	Get the board name inserted to Slot 3
	Acceptable	"000_%1" [CR]
Response	%1	The same data as CR_NMSLOT1
Response	Unacceptable	"?" [CR]

Page 74

9.7.14 CR_NMSLOT4 Command

Command	"CR_NMSLOT4" [CR]
Details	Get the board name inserted to Slot 4
	Acceptable	"000_%1" [CR]
Response	%1	The same data as CR_NMSLOT1
Response	Unacceptable	"?" [CR]

9.7.15 CR_IDSLOT1 Command

Command	"CR_IDSLOT1" [CR]
Details	Get ID information on Slot 1.This command is used to recognize the inserted board and specify the valid Input source.
	Acceptable	"000_%1" [CR]
Response	%1	"08" DUAL-SDI board Valid Input Source: SDI1, SDI2 "18" New HDCP-DVI board Valid Input Source: DIGITAL, ANALOG, HDCP, SCART "19" New Component & Video board Valid Input Source: ANALOG, YPBPR, VIDEO, S-VIDEO "32" On-board(DVI-D+D-Sub+HDMI) Valid Input Source: DIGITAL, ANALOG, HDCP, SCART, HDMI "42" On-board(5BNC+S-video) Valid Input Source: ANALOG, YPBPR, VIDEO, S-VIDEO "99" No board inserted
	Unacceptable	"?" [CR]

9.7.16 CR_IDSLOT2 Command

Command	"CR_IDSLOT2" [CR]
Details	Get ID information on Slot 2. This command is to recognize the inserted slot board and specify the valid Input source.
Acceptable "000_%1" [CR]		"000_%1" [CR]
Response	%1	The same as CR_IDSLOT1
	Unacceptable	"?" [CR]

9.7.17 CR IDSLOT3 Command

Command	"CR_IDSLOT3" [CR]
Details	Get ID information on Slot 3. This command is to recognize the inserted slot board and specify the valid Input source.
	Acceptable	"000_%1" [CR]
Response	%1	The same as CR_IDSLOT1
	Unacceptable	"?" [CR]

Page 75

9.7.18 CR_IDSLOT4 Command

	" [CR]
Details	Get ID informat This command source.	ID information on Slot 4. command is to recognize the inserted slot board and specify the valid Inpurce.
Response	Acceptable	"000_%1" [CR]
	%1	The same as CR_IDSLOT1
	Unacceptable	"?" [CR]

Page 76

9.8 Screen Status Read Commands

9.8.1 CR SCREEN Command

Command	"CR_SCREEN" [CR]
Details	Get currently s	Get currently selected screen image size
	Acceptable	"000_%1" [CR]
Response	%1	"NORMAL" Normal mode "ZOOM" Zoom mode "NATURAL" Natural wide mode "FULL" Full mode "TRUE" True mode "CUSTOM" Custom mode
	Unacceptable	"Error Code" [CR] When command is invalid in the given condition (such as being selected input) "?" [CR] When unknown command is received

9.8.2 CR_KYSTNMODE Command

Command	"CR_KYSTNMODE" [CR]
Details	Get setting status of Keystone Store Mode
	Acceptable	"000_%1" [CR]
Response	%1	"STR" Store mode is "Store" "RST" Store mode is "Reset"
	Unacceptable	"?" [CR] When unknown command is received

9.8.3 CR_CEIL Command

Command	"CR_CEIL" [CF	"CR_CEIL" [CR]
Details	Get setting stat	tus of Ceiling
	Acceptable	"000_%1" [CR]
Response	%1	"ON" Ceiling projection is enabled "OFF" Ceiling projection is disabled
	Unacceptable	"Error Code" [CR]

9.8.4 CR REAR Command

Command	"CR_REAR" [CR]
Details	Get setting stat	us of Rear function
	Acceptable	"000_%1" [CR]
Response	%1	"ON" Rear projection is enabled "OFF" Rear projection is disabled
	Unacceptable	"Error Code" [CR]

9.8.5 CR_VSCALE Command

Command	"CR_VSCALE"	[CR]
Details	Get setting stat	us of V scale
	Acceptable	"000_%1" [CR]
Response	%1	"-32" - "035"
	Unacceptable	"Error Code" [CR]

Page 77

9.8.6 CR_VPOS Command

Command	"CR_VPOS" [CR]
Details	Get setting stat	us of V Position
Response	Acceptable	"000_%1" [CR]
	%1	"-15" - "015"
	Unacceptable	"Error Code" [CR]

9.8.7 CR_HSCALE Command

Command	"CR_HSCALE"	[CR]
Details	Get setting stat	us of H scale
	Acceptable	"000_%1" [CR]
Response	%1	"-32" - "035"
	Unacceptable	"Error Code" [CR]

9.8.8 CR_HPOS Command

Command "CR_HPOS" [CR]		R]
Details	Get setting stat	us of H Position
	Acceptable	"000_%1" [CR]
Response	%1	"-15" - "015"
	Unacceptable	"Error Code" [CR]

Page 78

9.9 Lamp Status Read Commands

9.9.1 CR LAMPREPL Command

Command	"CR_LAMPRE	"CR_LAMPREPL" [CR]
Details	Get the information	ation of Lamp Replacement time
	Acceptable	"000_%1" [CR]
Response	%1	"2*" 2 indicates 2 lamps are used in this model. indicates the status of each lamp in lamp number order. "Y" means the lamp operating time is over the threshold for lamp replacement, and "N" means it has not reached to. e.g. "2YN" This indicates it is 2-lamp system, and Lamp #2 has not been reached to the replacement time while #1 should be replaced.
	Unacceptable	"?" [CR]

9.9.2 CR_LAMPMODE Command

Command	"CR_LAMPMO	"CR_LAMPMODE" [CR]
Details	Get Lamp mode	e setting status
	Acceptable	"000_%1" [CR]
Response	%1	"FULL" Lamp mode is set to 2-lamp (FULL) "LAMP1" Lamp mode is set to Lamp1 "LAMP2" Lamp mode is set to Lamp2
	Unacceptable	"?" [CR]

9.9.3 CR_AUTOLAMPCONTRL Command

Command	"CR_AUTOLAM	"CR_AUTOLAMPCONTRL" [CR]
Details	Details Get selected Lamp control mode
	Acceptable	"000_%1" [CR]
Response	%1	"NORMAL" NORMAL is selected. "ECO1" ECO1 is selected. "ECO2" ECO2 is selected.
	Unacceptable	"Error Code" [CR]

9.9.4 CR_LAMPSTS Command

Command	"CR_LAMPSTS" [CR]
Details	Get the information	ation of Lamp lighting status
	Acceptable	"000_%1" [CR]
Response	%1	"2**" The first character indicates 2 lamps are used in this model. The following characters indicate each lamp status in lamp number order as showed below. "1" Lamp is ON "O" Lamp is OFF "X" Lamp Failure e.g. "2IO" This indicates it is 2-lamps system, Lamp #1 is ON, and #2 is OFF.
	Unacceptable	"?" [CR]

Page 79

9.9.5 CR INFLAMP Command

Command	"CR_INFLAMP	" [CR]
Details	Get Lamp mod	e switching status
	Acceptable	"000_%1" [CR]
Response	%1	"NML" in Normal status (lamp switching operation is not active.)
	Unacceptable	"?" [CR]

9.9.6 CR_PROJH Command

Command	"CR_PROJH" [CR]
Details	Get total running time of projector (in hours)
Response	Acceptable	"000_%1" [CR]
	%1	"0000000" – "0099999"
	Unacceptable	"?" [CR]

9.9.7 CR_HMLAMP Command

Command	"CR_HMLAMP" [CR]
Details	Get total lamp number
	Acceptable	"000_%1" [CR]
Response	%1	"002"
Response	Unacceptable	"?" [CR]

9.9.8 CR LAMPH Command

Command	"CR_LAMPH" [	"CR_LAMPH" [CR]
Details	Get Lamp runn * return actual	Get Lamp running time (in hours) * return actual lamp running time
	Acceptable	"000_%1_%2_%3_%4" [CR]
Response	%1_%2 %3_%4	Lamp 1 data comes first, and then one space, after that lamp 2 data is followed. %1 = lamp No.1 %2 = lamp No.2 %3 = lamp No.3 %4 = lamp No.4 In the case of 2-lamps model, % 1 and % 2 are only used (There are no % 3 and % 4 ) e.g.; "00410_00410_00410_00410" [CR] ••••• → Lamp No.1 = 410 Hours Lamp No.2 = 410 Hours Lamp No.3 = 410 Hours Lamp No.4 = 410 Hours
	Unacceptable	"?" [CR]

Page 80

9.9.9 CR_LAMPCORRESPH Command

Command	"CR_LAMPCORRESPH" [CR]
Details	Get Lamp running time (in hours) *return lamp running time multiplied by a coefficient (not actual running time)
	Acceptable	"000_%1" [CR]
Response	%1	"00000"-"99999"
Response	Unacceptable	"Error Code" [CR]

9.9.10 CR LAMPINTERVAL Command

Command	"CR_LAMPINTERVAL" [CR]
Details	Get setting stat	Get setting status of Lamp interval
	Acceptable	"000_%1" [CR]
Response	%1	"AUTO" Auto is selected "0024" 24 Hours is selected "0200" 200 Hours is selected "0500" 500 Hours is selected "1000" 1000 Hours is selected "2000" 2000 Hours is selected "OFF" Off is selected
	Unacceptable	"?" [CR]

9.9.11 CR_LAMPLIFECONTRL Command

Command	"CR_LAMPLIFECONTRL" [CR]
Details	Get setting status of Lamp life control. (Available only in the normal Power ON status)
Response	Acceptable	"000_%1" [CR]
	%1	"MODE1" Mode1 is selected "MODE2" Mode2 is selected
	Unacceptable	"Error Code" [CR]

Page 81

9.10 Setting Status Read Commands

9.10.1 CR LANG Command

Command	"CR_LANG" [C	"CR_LANG" [CR]
Details	Get selected la	nguage
	Acceptable	"000_%1" [CR]
Response	%1	"ENG" English is selected "DEU" German is selected "FRA" French is selected "ITA" Italian is selected "ESP" Spanish is selected "POR" Portuguese is selected "NED" Dutch is selected "SVE" Swedish is selected "KOR" Chinese is selected "KOR" Japanese is selected "RUS" Russian is selected
	Unacceptable	"?" [CR]

9.10.2 CR SIMPLEMENU Command

Command	"CR_SIMPLEMENU" [CR]
Details	Get setting status of Simple menu
Response	Acceptable	"000_%1" [CR]
	%1	"ON" On is selected "OFF" Off is selected
	Unacceptable	"Error Code" [CR]

9.10.3 CR_MENUSIZE Command

Command	"CR_MENUSIZE" [CR]
Details	Get setting status of Menu size
Response	Acceptable	"000_%1" [CR]
	%1	"NORMAL" Normal is selected "DOUBLE" Double is selected
	Unacceptable	"Error Code" [CR]

9.10.4 CR DISP Command

Command	"CR_DISP" [CR]
Details	Get Display setting status
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Display is set to ON. "CNTDWNOFF" Display is set to Count down OFF. "OFF" Display is set to OFF.
	Unacceptable	"?" [CR]

Page 82

9.10.5 CR_BACKGND Command

Command	"CR_BACKGND" [CR]
Details	Get setting status of Screen for no signal
Response	Acceptable	"000_%1" [CR]
	%1	"BLUE" Blue Back is selected "USER" User is selected "BLACK" Black Back is selected
	Unacceptable	"Error Code" [CR]

9.10.6 CR LOGO Command

Command	"CR_LOGO" [CR]
Details	Get Logo setting status
Response	Acceptable	"000_%1" [CR]
	%1	"DFLT" Default Logo is enabled "USER" User is enabled "OFF" Off is enabled
	Unacceptable	"?" [CR]

9.10.7 CR_LOGOLOCK Command

Command	"CR_LOGOLOCK" [CR]
Details	Get setting status of Logo Lock function
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Logo Lock is ON "OFF" Logo Lock is OFF
	Unacceptable	"Error Code" [CR]

9.10.8 CR FANSPEED Command

Command	"CR_FANSPEED" [CR]
Details	Get currently selected Fan Control Speed
Response	Acceptable	"000_%1" [CR]
	%1	"MAX" Max speed of Fan Control is selected "NOR" Normal speed of Fan Control is selected
	Unacceptable	"?" [CR]

9.10.9 CR RCODE Command

Command	"CR_RCODE" [CR]
Details	Get currently selected Remote Control code
Response	Acceptable	"000_%1" [CR]
	%1	"001" Code1 : "008" Code8
	Unacceptable	"?" [CR]

Page 83

9.10.10 CR_RSENS Command

Command	"CR_RSENS" [CR]
Details	Get selected location of infrared remote receiver of remote control
	Acceptable	"000_%1" [CR]
Response	%1	"ALL" Front and back and top parts are valid "FRONTTOP" Both front and top parts are valid "BACKTOP" Both back and top parts are valid "FRONTBACK" Both front and back parts are valid "FRONT" Only front part is valid "TOP" Only top part is valid "BACK" Only back part is valid
	Unacceptable	"?" [CR]

9.10.11 CR_P-MANE Command

Command	"CR_P-MANE" [CR]
Details	Get setting status of Power management
Response	Acceptable	"000_%1" [CR]
	%1	"OFF"Power Management is disabled "READY"Power Management is set to Ready "SHUTDOWN"Power Management is set to Shut Down mode
	Unacceptable	"?" [CR]

9.10.12 CR P-MANETIME Command

Command	"CR_P-MAETIME" [CR]
Details	Get setting time for starting Power Management function
Response	Acceptable	"000_%1" [CR]
	%1	"001 – 030" 1 to 30 minutes
	Unacceptable	"?" [CR]

9.10.13 CR_ONSTA Command

Command	"CR_ON-STA" [CR]
Details	Get Power ON Start setting status
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Power ON Start is set to ON. "OFF" Power ON Start is set to OFF.
	Unacceptable	"?" [CR]

9.10.14 CR_SECURITY Command

Command	"CR_SECURITY" [CR]
Details	Get ON/OFF setting status of Security on menu.
Response	Acceptable	"000_%1" [CR]
	%1	"ON" PJ is locked "OFF" PJ is not locked.
	Unacceptable	"Error Code" [CR]

Page 84

9.10.15 CR_PJLOCKNOW Command

Command	"CR_PJLOCKNOW" [CR]
Details	Get actual setti	Get actual setting status of PIN code lock
	Acceptable	"000_%1" [CR]
Response	%1	"LOCK" PJ is locked PIN code lock is set to ON1/ON2 on the menu and PJ PIN code is not entered, therefore PJ is actually locked. "FREE" PJ is unlocked (either A or B) A) PJ lock is set to OFF on the menu B) PJ lock is set to ON1/ON2 on the menu, but PIN code Lock mode is canceled because PJ PIN code is entered.
	Unacceptable	"Error Code" [CR]

9.10.16 CR_PJLOCMENU Command

Command	"CR_PJLOCKMENU" [CR]
Details	Get ON/OFF setting status of PIN code lock on menu
	Acceptable	"000_%1" [CR]
Response	%1	"ON1" PIN code lock ON 1 is set on the menu "ON2" PIN code lock ON 2 is set on the menu "OFF" PIN code lock OFF is set on the menu
Response	Unacceptable	"Error Code" [CR]

9.10.17 CR FILH Command

Command	"CR_FILH" [CR]
Details	Get Filter used time
Response	Acceptable	"000_%1" [CR]
	%1	"00000 - 99999"
	Unacceptable	"Error Code" [CR]

9.10.18 CR FILCOND Command

Command	"CR_FILCOND" [CR]
Details	Get status of filter clog
Response	Acceptable	"000_%1" [CR]
	%1	"CLOG" = Filter is clogged "WARN" = Filter is nearly clogged "CLEAN" = Filter is not clogged
	Unacceptable	"Error Code" [CR]

9.10.19 CR_FILREPL Command

Command	"CR_FILREPL" [CR]
Details	Get status of Filter cleaning / replacement time
Response	Acceptable	"000_%1" [CR]
	%1	"1Y"Filter Exchange time is over value of Filter Message. "1N"Filter Exchange time is not over value of Filter Message.
	Unacceptable	"Error Code" [CR]

Page 85

9.10.20 CR FILTIMER Command

Command	"CR_FILTIMER" [CR]
Details	Get time to display Filter cleaning / replacement warning on screen
Response	Acceptable	"000_%1" [CR]
	%1	"1000" Display massage by 1000h used. "2000" Display massage by 2000h used. "3000" Display massage by 3000h used. "OFF" Off(Warning display is not displayed)
	Unacceptable	"Error Code" [CR]

9.10.21 CR_FILREMAIN Command

Command	"CR_FILREMAIN" [CR]
Details	Get remaining number of usable Filter scroll
Response	Acceptable	"000_%1" [CR]
	%1	"09" = Remaining number of usable Filter scroll : 9 times "00" = Remaining number of usable Filter scroll : 0 time
	Unacceptable	"Error Code" [CR]

9.10.22 CR_TESTPAT Command

Command	"CR_TESTPAT" [CR]
Details	Get setting status of Test pattern
	Acceptable	"000_%1" [CR]
Response	%1	"COLOR" Color bar is displayed "GRAD1" 16step(white→black) is displayed "GRAD2" 16step(white→black) is displayed "GRAD3" 16step(white↓black) is displayed "GRAD4" 16step(white↑black) is displayed "WHITE" 16step(white is displayed "BLACK" All black is displayed "CROSS" Cross is displayed "OFF" Test pattern display is not displayed
	Unacceptable	"Error Code" [CR]

9.10.23 CR KEYDIS Command

Command	"CR_KEYDIS" [CR]
Details	Get setting status of RC/KEY use limitation (valid or invalid)
Response	Acceptable	"000_%1" [CR]
	%1	"NONE" RC & KEY are valid "RC" RC is invalid "KEY" KEY is invalid
	Unacceptable	"?" [CR]

Page 86

9.10.24 CR_SHUTRCPROT Command

Command	"CR_SHUTRCPROT" [CR]
Details	Get status if Shutter can be controlled by R/C
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Shutter is not controllable by R/C "OFF" Shutter is controllable by R/C
	Unacceptable	"Error Code" [CR]

9.10.25 CR SHUTKEYPROT Command

Command	"CR_SHUTKEYPROT" [CR]
Details	Get status if Shutter can be controlled by key on the side panel
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Shutter is not controllable by key on the side panel "OFF" Shutter is controllable by key on the side panel
	Unacceptable	"Error Code" [CR]

9.10.26 CR SHUTH Command

Command	"CR_SHUTH" [CR]
Details	Get time setting to start the shutter management
	Acceptable	"000_%1" [CR]
Response	%1	"005" 5 minutes "006" 6 minutes : "479" 479 minutes "480" 480 minutes
	Unacceptable	"Error Code" [CR]

9.10.27 CR SHUTEFFECT Command

Command	"CR_SHUTEFFECT" [CR]
Details	Get status of Shutter effect function.
Response	Acceptable	"000_%1" [CR]
	%1	"OFF"Fade in / out function is set to Off. "L1"Fade in / out function is set to L1. "L2"Fade in / out function is set to L2.
	Unacceptable	"Error Code" [CR]

9.10.28 CR_SHUTRELEASE Command

Command	"CR_SHUTRELEASE" [CR]
Details	Get status of Shutter release key function.
Response	Acceptable	"000_%1" [CR]
	%1	"ANY"Enable to release Shutter with any key "SHUTTER" Enable to release Shutter with only "SHUTTER" key
	Unacceptable	"Error Code" [CR]

Page 87

9.10.29 CR_DELAYCTRL Command

Command	"CR_DELAYCTRL" [CR]
Details	Get setting status of Video delay control
	Acceptable	"000_%1" [CR]
Response	%1	"OFF" Set Video delay control to OFF "LOW" Set Video delay control to LOW "MID" Set Video delay control to MID "HIGH" Set Video delay control to HIGH
Response	Unacceptable	"Error Code" [CR]

9.10.30 CR_CCAPTIONSIDP Command

Command	"CR_CCAPTIONDISP" [CR]
Details	Get selected channel of Closed caption
	Acceptable	"000_%1" [CR]
Response	%1	"OFF" Off "CC1" CC1 is selected "CC2" CC2 is selected "CC3" CC3 is selected "CC4" CC4 is selected
	Unacceptable	"Error Code" [CR]

9.10.31 CR_CCAPTIONCOLOR Command

Command	"CR_CCAPTIONCOLOR" [CR]
Details	Get selected color of Closed caption
Response	Acceptable	"000_%1" [CR]
	%1	"COLOR" Color is selected "WHITE" White is selected
	Unacceptable	"Error Code" [CR]

9.10.32 CR_FRAMELOCK Command

Command	"CR_FRAMELOCK" [CR]
Details	Get status of F	Get status of Frame lock setting.
	Acceptable	"000_%1" [CR]
Response	%1	"AUTO" "Auto" is selected "23.98" "Manual, 23.98 Hz." is selected "25.00" "Manual, 25.00 Hz." is selected "29.97" "Manual, 29.97 Hz." is selected "30.00" "Manual, 30.00 Hz." is selected "50.00" "Manual, 50.00 Hz." is selected "59.94" "Manual, 59.94 Hz." is selected "60.00" "Manual, 60.00 Hz." is selected "BLANK""Manual," is selected
	Unacceptable	"Error Code" [CR]

Page 88

9.10.33 CR_FRAMELOCKADJ Command

Command	"CR_FRAMELOCKADJ" [CR]
Details	Get manually set value of Frame lock.
Response	Acceptable	"000_%1" [CR]
	%1	"23.500" - "62.000"
	Unacceptable	"Error Code" [CR]

9.10.34 CR_PIP Command

Command	"CR_PIP" [CR]
Details	Get setting status of "Picture in Picture"
	Acceptable	"000_%1" [CR]
Response	%1	"OFF" Off is selected "USER1" User1 is selected "USER2" User2 is selected "USER3" User3 is selected "USER4" User4 is selected "USER5" User5 is selected
	Unacceptable	"Error Code" [CR]

9.10.35 CR PIPMODE Command

Command	"CR_PIP" [CR]
Details	Get mode of "Picture in Picture"
Response	Acceptable	"000_%1" [CR]
	%1	"PINP" P in P is selected "PBYP" P by P is selected
	Unacceptable	"Error Code" [CR]

Page 89

9.10.36 CR_PIPMAININP Command

Command	"CR_PIPMAININP" [CR]
Details	Get Input and	Source of "Picture in Picture". (Main picture)
	Acceptable	"000_%1_%2" [CR]
	%1	"1" Input1 is selected "2" Input2 is selected "3" Input3 is selected "4" Input4 is selected
Response	%2	"DIGITAL" DVI Input is selected "ANALOG ANALOG RGB is selected "VIDEO" Video Input is selected "S-VIDEO" S-VIDEO Input is selected "YPBPR" Y/Pb/Pr Input is selected "SDI1" SDI1 Input is selected "SDI2" SDI2 Input is selected "SCART" SCART Input is selected "HDCP" HDCP Input is selected "HDMI"
	Unacceptable	"Error Code" [CR]

9.10.37 CR_PIPSUBINPU Command

Command	"CR_PIPSUBI	"CR_PIPSUBINP" [CR]
Details	Get Input and S	Source of "Picture in Picture". (Sub picture)
	Acceptable	"000_%1_%2" [CR]
Response	%1	"1" Input1 is selected "2" Input2 is selected "3" Input3 is selected "4" Input4 is selected
	%2	"DIGITAL" DVI Input is selected "ANALOG ANALOG RGB is selected "VIDEO" Video Input is selected "S-VIDEO" S-VIDEO Input is selected "YPBPR" Y/Pb/Pr Input is selected "SDI1" SDI1 Input is selected "SDI2" SDI2 Input is selected "SCART" SCART Input is selected "HDCP"
	Unacceptable	"Error Code" [CR]

Page 90

9.10.38 CR_PIPSIZE Command

Command	"CR_PIPSIZE" [CR]
Details	Get picture size	e of "Picture in Picture". (Sub picture)
	Acceptable	"000_%1_%2" [CR]
Response	%1	"1" 10% is selected(Main size) "2" 20% is selected(Main size) "3" 30% is selected(Main size) "4" 40% is selected(Main size) "5" 50% is selected(Main size) "6" 60% is selected(Main size) "7" 70% is selected(Main size) "8" 80% is selected(Main size) "0" 90% is selected(Main size) "10" 100% is selected(Main size)
	%2	"1" 10% is selected(Sub size) "2" 20% is selected(Sub size) "3" 30% is selected(Sub size) "4" 40% is selected(Sub size) "5" 50% is selected(Sub size)
	Unacceptable	"Error Code" [CR]

9.10.39 CR PIPFRAMELOCK Command

Command	"CR_PIPFRAMELOCK" [CR]
Details	Get setting status of Frame lock of "Picture in Picture".
Response	Acceptable	"000_%1" [CR]
Response	%1	"MAIN" Main picture is selected "SUB" Sub picture is selected
	Unacceptable	"Error Code" [CR]

9.10.40 CR PIPSTORE Command

Command	"CR_PIPSTORE" [CR]
Details	Get status (Free or Stored) of User1-User5 of "Picture in Picture".
Response	Acceptable	"000_%1" [CR]
	%1	"SFFFF" Only User1 is Stored, others are Free : "FFFFS" Only User5 is Stored, others are Free "SSSSS" All Stored
	Unacceptable	"Error Code" [CR]

9.10.41 CR_EDGEBLENDING Command

Command	"CR_EDGEBLENDING" [CR]
Details	Get setting status of Edge blending
Response	Acceptable	"000_%1" [CR]
	%1	"ON" On is selected "OFF" Off is selected
	Unacceptable	"Error Code" [CR]

Page 91

9.10.42 CR_EDGEBLENDING Command

Command	"CR_BLEND" [CR]
Details	Get all values of	of width of Edge blending
	Acceptable	"000_%1_%2_%3_%4" [CR]
Response	%1, %2, %3, %4	Left width data comes first, and then one space, after that right width data is followed. %1 = Left width %2 = Right width %3 = Top width %4 = Bottom width e.g. "100_100_100_100"[CR] Left = width 100 Right = width 100 Top = width 100 Bottom = width 100
	Unacceptable	"Error Code" [CR]

9.10.43 CR_BLENDBLK Command

Command	"CR_BLENDBLK" [CR]
Details	Get all values of	Get all values of Black level of Edge blending
	Acceptable	"000_%1_%2_%3" [CR]
Response	%1, %2, %3	Data of red comes first, and then one space, after that data of green is followed. %1 = Red %2 = Green %3 = Blue e.g. "0100_0100_0100"[CR] Red = 100 Green = 100 Blue = 100
	Unacceptable	"Error Code" [CR]

9.10.44 CR BLENDTESTPAT Command

Command	"CR_BLENDTESTPAT" [CR]
Details	Get setting status of Test pattern of Edge blending
Response	Acceptable	"000_%1" [CR]
	%1	"ON" On is selected "OFF" Off is selected
	Unacceptable	"Error Code" [CR]

9.10.45 CR_COLORMATCHING Command

Command	"CR_COLORMATCHING" [CR]
Details	Get setting status of Color matching
Response	Acceptable	"000_%1" [CR]
	%1	"ON" On is selected "OFF" Off is selected
	Unacceptable	"Error Code" [CR]

Page 92

9.10.46 CR_CMMSXY_%1 Command

Command	"CR_CMMSXY_%1" [CR]
Details	Get "x","y" value of Measured of Color matching
Response	Acceptable	"000_%2_%3" [CR]
	%1	"RED" value of Red is selected "GREEN" value of Green is selected "BLUE" value of Blue is selected "WHITE" value of White is selected "HALFWHITE" value of Half white is selected
	%2	"0000"-"1000" "x" value of color of %1
	%3	"0000"-"1000" "y" value of color of %1
	Unacceptable	"Error Code" [CR]

9.10.47 CR_CMMSL_%1 Command

Command	"CR_CMMSL_%1" [CR]
Details	Get "L" value of Measured of Color matching
	Acceptable	"000_%2" [CR]
Response	%1	"RED" value of Red is selected "GREEN" value of Green is selected "BLUE" value of Blue is selected "WHITE" value of White is selected "HALFWHITE" value of Half white is selected
	%2	"0000"-"1000" "L" value of color of %1
	Unacceptable	"Error Code" [CR]

9.10.48 CR_CMTGXY_%1 Command

Command	"CR_CMMTGXY_%1" [CR]
Details	Get "x""y" value	Get "x""y" value of Target of Color matching
	Acceptable	"000_%2" [CR]
Response	%1	"RED"value of Red is selected "GREEN"value of Green is selected "BLUE"value of Blue is selected "WHITE"value of White is selected "CYAN"value of Cyan is selected "MAGENTA"value of Magenta is selected "YELLOW"value of Yellow is selected
	%2	"0000"-"1000" "x" value of color of %1
	%3	"0000"-"1000" "y" value of color of %1
	Unacceptable	"Error Code" [CR]

Page 93

9.10.49 CR_CMTGG_%1 Command

Command	"CR_CMMTGG_%1" [CR]
Details	Get "g" value of Target of Color matching
	Acceptable	"000_%2" [CR]
Response	%1	"RED" value of Red is selected "GREEN" value of Green is selected "BLUE" value of Blue is selected "WHITE" value of White is selected "CYAN" value of Cyan is selected "MAGENTA" value of Magenta is selected "YELLOW" value of Yellow is selected
	%2	"0000"-"1000" "g" value of color of %1
	Unacceptable	"Error Code" [CR]

9.10.50 CR_CMAUTOTESTPAT Command

Command	"CR_CMAUTOTESTPAT" [CR]
Details	Get setting status of Auto test pattern of Color matching
Response	Acceptable	"000_%1" [CR]
	%1	"ON" On is selected "OFF" Off is selected
	Unacceptable	"Error Code" [CR]

9.10.51 CR_CMMSTESTPAT Command

Command	"CR_CMMSTE	"CR_CMMSTESTPAT" [CR]
Details	Get setting status of Test pattern(Measured) of Color matching
	Acceptable	"000_%1" [CR]
Response	%1	"RED" Red is displayed "GREEN" Green is displayed "BLUE" Blue is displayed "WHITE" White is displayed "HALFWHITE" Half white is displayed "OFF"Test pattern display is not displayed
	Unacceptable	"Error Code" [CR]

9.10.52 CR CMTGTESTPAT Command

Command	"CR_CMTGTE	"CR_CMTGTESTPAT" [CR]
Details	Get setting stat	Get setting status of Test pattern(Target) of Color matching
	Acceptable	"000_%1" [CR]
Response	%1	"RED" Red is displayed "GREEN" Green is displayed "BLUE" Blue is displayed "WHITE" White is displayed "CYAN" Cyan is displayed "MAGENTA" Magenta is displayed "YELLOW" Yellow is displayed "OFF" Test pattern display is not displayed
	Unacceptable	"Error Code" [CR]

Page 94

9.10.53 CR_DYNAMICBLACK Command

Command	"CR_DYNAMICBLACK" [CR]
Details	Get setting stat	tus of DynamicBlack
	Acceptable	"000_%1" [CR]
Response	%1	"OFF" Off is selected "LOW" Low is selected "HIGH" High is selected
	Unacceptable	"Error Code" [CR]

9.10.54 CR HDMISETUP Command


Command	"CR_HDMISET	"CR_HDMISETUP" [CR]
Details	Get setting stat	us of HDMI setup
	Acceptable	"000_%1" [CR]
Response	%1	"NORMAL" Normal is selected "ENHANCED" Enhanced is selected
	Unacceptable	"Error Code" [CR]

Page 95

9.11 Other Status Read Commands

9.11.1 CR STATUS Command

Command	"CR_STATUS"	[CR]
Details	Get operating s Same as "CR0	status of Projector " in basic command except error code follows it.
	Acceptable	"000_%1" [CR]
Response	%1	"00" = Power ON "80" = Standby "40" = Countdown in process "20" = Cooling Down in process "10" = Power Failure "28" = Cooling Down in process due to abnormal temperature "88" =Standby after Cooling Down due to abnormal temperature "02" = Invalid RS-232C Command "24" = Power Save/Cooling Down in process "04" = Power Save "21" = Cooling Down in process after turned off due to lamp failure "81" = Standby after Cooling Down due to lamp failure "2C" = Cooling Down in process after Power Off due to Shutter management "8C" = Standby after Cooling Down due to Shutter management
	Unacceptable	"Error Code" [CR]

9.11.2 CR_SIGNAL Command

	[CR]
Details	Get status if the	ere is any signal or not
Response	Acceptable	"000_%1" [CR]
	%1	"ON" There is signal "OFF" There is no signal
	Unacceptable	"?" [CR]

9.11.3 CR_VMUTE Command

Command	"CR_VMUTE" [CR]
Details	Get Video mute setting status
	Acceptable	"000_%1" [CR]
Response	%1	"ON" Video mute is set to ON (Shutter Close). "OFF" Video mute is set to OFF (Shutter Open).
	Unacceptable	"?" [CR]

9.11.4 CR_FREEZE Command

	[CR]
Details	Get Freeze sett	ting status
Response	Acceptable	"000_%1" [CR]
	%1	"ON" Freeze is set to ON. "OFF" Freeze is set to OFF.
	Unacceptable	"?" [CR]

Page 96

9.11.5 CR_P-TIMER Command

Command	"CR_P-TIMER" [CR]
Details	Get Presentation Timer operating status
	Acceptable	"000_%1" [CR]
Response	%1	"ON" Presentation Timer is ongoing. "STOP" Presentation Timer is paused. "OFF" Presentation Timer is not active.
	Unacceptable	"?" [CR]

9.11.6 CR_TEMPWARN Command

Command	"CR_TEMPWA	"CR_TEMPWARN" [CR]
Details	Get the information about the temperature inside the projector (close to the abnormal or in the abnormal status/in the safe temperature level/abnormal status is not detected). It is possible to get the information about more than one sensor all at once if it applicable.
	Acceptable	"000_%1" [CR]
Response	%1	* Sensor 1 data comes first, and then one space, after that sensor 2 data is followed. Each data is as below: W" in or close to the abnormal temp. (Warning Temp.) S" in the safe level of temperature (Safe Temp.). *N" the given sensor does not detect abnormal temp. e.g. "S_W" [CR] indicates that the temperature detected at Sensor 1 is in the safe level while Sensor 2 in the abnormal temperature.
	Unacceptable	"?" [CR]

Page 97

9.11.7 CR_TEMPFAIL Command

Command	"CR_TEMPFAI	L" [CR]
Details	Get the temper It is possible to applicable.	ature inside the projector when the abnormal status occurs. b get the temperatures for more than one sensor all at once if it is
	Acceptable	"000_%1" [CR]
		e.g. "_31.5F"[CR] indicates a space. When the temperature goes under 0, the first character is "-", not a space, as in "-05.5F". With more than one temperature sensors installed, projector returns the responses for each sensor in a row.
Response	%1	e.g. "_31.5F_35.2S" [CR] The first data indicates sensor 1 data, then one space, and sensor 2 data is followed. Last character in each data indicates the sensor's status. In the abnormal temperature
		The second example above indicates that the temperature detected by sensor 1 is 31.5 which means in the abnormal temperature, and at sensor 2 is 32.5 degrees which is in the safe temperature.
		When the abnormal temperature status is not occurred the data should be "_00.0S". When the projector is reset, "_00.0S" is set. Every time abnormal temperature status is detected, it renews the data and returns it. It only returns the renewed data of the latest abnormal temperature and the previous data is cleared.
	Unacceptable	"?" [CR]

Page 98

Command	"CR_TEMP"[CF	R]
Details	Get the current It is possible to	temperature information inside a projector. get the temperatures all at once when several sensors installed.
	Acceptable	"000_%1_%2_%3_%4" [CR]
Response	%1	%1Sensor 1 temp. (External temp.) %2Sensor 2 temp. (Internal temp.1) %3Sensor 3 temp. (Internal temp.2) %4Sensor 4 temp. (Internal temp.3) %1, %2 are fixed 6 characters There is one space between %1 and %2 There is one space between %2 and %3 There is one space between %3 and %4 e.g. "_31.5F" : "_" indicates a space. When the temperature goes under 0, the first character is "-", not a space, as in "-05.5F". Last character in each data indicates the sensor's status. "F" Exceeding critical temp. (abnormal temp.) "W" Sensor temp. is safe (Safe temp.) "N" Sensor detects no critical temp. "E" Unable to return the temp. data With more than one temperature sensors installed, projector returns responses in a row. e.g. "_31.5F35.2S38.0W 38.0N" [CR] The first data indicates sensor 1 indicates 31.5 degrees and the temperature is abnormal, sensor 2 indicates 38.0 degrees and the temperature is safe, sensor 3 indicates 38.0 degrees and the temperature is approaching critical state, sensor 4 indicates 38.0 degree and this sensor detects no critical temp. When it cannot return the temperature data due to hardware error, the last character is "E" as in "_00.0E" It might happen for some projectors that the temperature continues to go up to abnormal status as long as lamp ballasts are hot. Therefore when in Standby mode or for several tens of seconds after Power is ON, any treatment of Power Failure is not processed. In that case, the temperature data is represented as "N".
	Unacceptable	\| "?" [CR]

9.11.8 CR_TEMP Command

9.11.9 CR_SERIALNO Command

Command	"CR_SERIALN	"CR_SERIALNO" [CR]
Details	Get value of the	e serial number.
	Acceptable	"000_%1" [CR]
Response	%1	Eight digits of alphanumeric characters
	Unacceptable	"?" [CR]

9.11.10 CR SHUTCOND Command

Command	"CR_SHUTCO	"CR_SHUTCOND" [CR]
Details	Get setting stat	us of Shutter
	Acceptable	"000_%1" [CR]
Response	%1	"SAFE" Shutter operation is normal. "FAIL" Shutter operation is abnormal.
	Unacceptable	"?" [CR]

Page 99

9.11.11 CR OPTCTRLNO Command

Command	"CR_OPTCTRLNO"[CR]
Details	Get value of Option control No.
Response	Acceptable	"000_%1" [CR]
	%1	Four digits of alphanumeric characters
	Unacceptable	"?" [CR]

9.11.12 CR_LENSTYPE Command

Command	"CR_LENSTYPE"[CR]
Details	Get which type of Lens is currently installed
Response	Acceptable	"000_%1" [CR]
	%1	Lens type On Axis Short Fixed Lens	%1 LNS-W52 (0.8:1)
		Short Zoom Lens	LNS-W51 (1.2-1.5:1)
		Short Zoom Lens	LNS-W53 (1.2-1.8:1)
		Standard Zoom Lens	LNS-S50 (1.8-2.8:1)
		Standard Zoom Lens	LNS-S51 (1.8-2.8:1)
		Long Zoom Lens	LNS-T50 (2.8-5.0:1)
		Ultra Long Zoom Lens	LNS-T51 (4.8-8.0:1)
	Unacceptable	"?" [CR]

9.11.13 CR_COLWHEELTYPE Command

Command	"CR_COLWHEELTYPE"[CR]
Details	Get which type of Color wheel is currently installed
Response	Acceptable	"000_%1" [CR]
	%1	"BRIGHTNESS" Color wheel for brightness is installed "COLREPRO" Color wheel for color reproduction is installed
	Unacceptable	"?" [CR]

Page 100

10. Command with Address Specification

10.1. Overview

- Commands with address are used to remote control more than one projector through RS-232C by a computer.

- The command with address is defined as a single command per line that starts with "A" and ends with carriage return (0x0D).

- When a projector receives carriage return (0x0D), it starts decoding.

- The address such as "A001" is prefixed to the Basic Serial Command or Expand Serial Command

already mentioned

e.g.) Eunctional Execution Command: "A001C05" [CR]

e.g.) Status Read Command: "A001CR0" [CR]

- Projector has the function to set up its own address in Service mode

Initial setting value is "No.001"

Available range of the value is "001" to "999"

- It clears the data in the receive buffer in the following cases.

When receiving LF (0x0A) or EOF (0x1A)
When it takes more than one second to receive a single command.

(Until receiving carriage return after the reception of the first data)

- It returns the response within 60ms

10.2. Functional Execution Command with address

10.2.1. Format

Commands with "FFF" as the address are valid to all projectors.

Command: string (Refer to Basic and Expand Serial Command)

2) The only projector with the appropriate address decodes the received command, and

when it is ready to receive the next command, it returns the response

[ACK] [CR]: When receiving Functional Execution Command (0x06, 0x0D)

" – " [CR] . When the received data cannot be decoded

However, when the address is "FEF" the projector executes the function but does not

return the response.