
INSTALLATION MANUAL
MODEL KA-WA-42V
Plasma Display Mount Unit
Mount Unit
Please read the instructions in the Installation Manual thoroughly before use. In particular,
please be careful to read the section on Safety matters.
Read and keep this Installation manual for later use.
■ Parts contained in the package
1AA6P1P4052-- (IDLNB)
NOTES ON INSTALLATION
• For customers safety, please install only after being careful to ascertain whether the place to
which it is to be mount is capable of supporting the combined weight of the Plasma Display
set and the Mount Unit together.
• Please make sure that at least two people are present during installation.
• Please make sure that all the screws and parts specified in the installation manual are used
in full number on installation.
Installation of the Plasma Display needs special knowledge. Installation should be made by
qualified personnel.
IMPORTANT NOTICE
The Mount Unit is intended for use only with the SANYO Plasma Display model number series
PDP-42WV1, PDP-42WV2. Use with other apparatus is capable of resulting in instability causing possible injury.
CAUTION
•
Phillips
screwdriver, # 2 tip.
•
Phillips
screwdriver, # 2 tip
with 12" shaft.
■ Required tools
Screws A (M8 x 30)
(4pcs.)
Screws B (M8 x 60)
(4pcs.)
Spacers
(4pcs.)
Bundling Band
(2pcs.)
Printed in Japan

2
Please carry out installation only after making absolutely sure that the surface of wall
is capable of bearing the total weight over a long period of time along with any reasonable stress resulting from earthquake or other external stresses.
If installation is carried out incorrectly or the strength of the wall is not properly ascertained,
this may lead to the Plasma Display falling down from its mountings and serious accident
occurring. Please carry out installation correctly in line with the following points.
• The surface of the wall must be able to support the combined weight of the Unit and the
Plasma Display together. Check the weight of the Unit and of the Display Unit before installation and then check the load-bearing capacity of the wall. If the load-bearing capacity of
the wall is insufficient, please use plenty of reinforcement.
• Weight of Unit . . . . . . . . . .approx. 3.6 kg (7.9 lbs)
• Weight of Plasma Display . .Refer to Instruction Manual. When speakers are used with
Display, weight of speakers must also be taken into
account.
CAUTION FOR INSTALLATION
If anything abnormal occurs, please remove plug and stay
away.
If there is any looseness, coming-away or unevenness in the
screws or other parts of the product, there is a danger that it
may fall off its mountings. In this case, and again, if there is any
smoke or strange smell, or if water or any other alien substance
gets into the screen, no picture appears on the screen, or there
is damage to the equipment, please do not use the Display, as
this may lead to accident or injury. After taking the following
steps, please contact your nearest sales dealer. Please do not
attempt any adjustment or repair work by yourself, as this may
be dangerous.
➀ Turn off the Display and remove the Power plug from wall out-
let.
➁ Enclose the area in order not to enter under the Plasma
Display.
WARNING FOR SAFETY INSTRUCTION
Contact to service center to take care of any necessary adjustment.
Please be sure to ask a service personnel to take care of any necessary moving, adjusting of
direction or angle. This is dangerous, so the customer should under no circumstances attempt
this by themselves as this may lead to accidents and injury.
Do not put weight on apparatus by hanging from or pulling on cord.
Do not under any circumstances hang from the Display unit once it is attached to wall, as this
may lead to it falling down, causing serious accident or even injury. Please be careful to make
sure that children refrain from doing this. Also, please be careful not to put any weight on the
apparatus by pulling the attached wires.
DANGER

3
• Make sure that the unit is out of the way of swinging doors or doors on furniture on installation. Do not install in any place where there is excess vibration or load as this may lead to
the unit falling down from its mountings, damage or injury.
• Do not install in bathroom, shower unit, outside, near window or anywhere where water might
come into contact with the unit as this may lead to fire or electric shock.
• Do not install near to the inlet or outlet for an air-conditioning system or anywhere where
there is dust, soot or a lot of tobacco smoke as this may lead to fire or breakdown of the
equipment.
• Do not install anywhere where the temperature is high or with high humidity as this may lead
to fire or electric shock.
• Do not install on the ceiling or any surface at an acute angle as this may cause heat to build
up internally, temperature to rise and fire to occur or the equipment to fall down from its
mountings, causing it to be damaged or injury to be sustained.
• Do not install in such a way as to close of the ventilation holes. Leave minimum distance (
more than 10cm for top and side, 6cm for bottom, and 3cm for behind) free around the ventilation holes so as to not impede proper ventilation. If internal temperature rises, this may
lead to fire or accident.
• Do not install near sprinklers or sensors as this may lead to malfunction or electric shock.
CAUTION FOR LOCATION OF INSTALLATION
• Do not customize any of the parts and do not use any damaged parts as this may lead to the
unit falling down from its mountings,accident or injury.
• Use the correct number of screws and bolts in the correct positions as indicated. Only use
the brackets provided. Failure to do so may lead to the unit falling down from its mountings,
accident or injury.
• Be careful not to get fingers trapped in wall brackets.
• When carrying the Plasma Display,hold the body of the Plasma Display.Do not handle it by
holding the attached accessory parts(such as speakers),otherwise it could result in damage.
CAUTION IN INSTALLATION
• Make absolutely certain that the weight of the unit is supported by pillars and beams made
of strong material.
• Do not attempt to directly mount to any wall that is not strong enough. Please do not attach
to decorative, non-load-bearing beams or ceiling brackets.
• If mounting to a concrete wall, please make sure to use anchors of sufficient strength to support total load.
Do not allow unit to get get! Do not use in bathroom or
shower unit!