Sanyo DSR-2016 Instruction Manual

INSTRUCTION MANUAL

Digital Video Recorder

with Multiplexer Function

About this manual

Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference.

DSR-2016

● Refer to the included CD-ROM for the German, French, Spanish and Italian “INSTRUCTION MANUAL”.

● Die “BEDIENUNGSANLEITUNG” in den Sprachen Deutsch, Französisch, Spanisch und Italienisch

finden Sie auf der beiliegenden CD-ROM.

● Utilisez le CD-ROM fourni pour consulter le “MANUEL D’INSTRUCTIONS” en allemand, français, espagnol et italien.

● Consulte en el CD-ROM suministrado el “MANUAL DE INSTRUCCIONES” en alemán, francés, español e italiano.

● Per il “MANUALE DI ISTRUZIONI” in Tedesco, Francese, Spagnolo e Italiano, fare riferimento al CD-ROM allegato.

Table of Contents

Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

These precautions must be followed for safety reasons. . . . iii

Follow the points outlined below for proper use . . . . . . . . . . vi

Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Main parts replacement timings . . . . . . . . . . . . . . . . . . . . 1

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Mounting the hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Names and functions of parts. . . . . . . . . . . . . . . . . . . . . . 3

Names of each part and connections. . . . . . . . . . . . . . . . 4

Basic connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Network connection (LAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Connecting to the RS-485 control terminal. . . . . . . . . . . . . . . 6

Switching the power on / off . . . . . . . . . . . . . . . . . . . . . . . 7

Switching the power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

BSwitching the power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pre-operation preparation . . . . . . . . . . . . . . . . . . . . . . . . . 8

Screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

ASetting the television system and the monitor output . . . 9

BSetting the clock (CLOCK SET) . . . . . . . . . . . . . . . . . . . . . . 9

CSetting the language (LANGUAGE). . . . . . . . . . . . . . . . . . 11

DSetting the RS-485 termination switch

(SANYO SSP side). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Monitoring the camera videos. . . . . . . . . . . . . . . . . . . . . 12

Single-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

BQuad-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

CMulti-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DCamera sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Operating the PTZ camera. . . . . . . . . . . . . . . . . . . . . . . . 14

Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Real time recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

BCONTINUOUS recording. . . . . . . . . . . . . . . . . . . . . . . . . . . 17

CMOTION recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

DALARM recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

ESCHEDULE recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Playing back recorded videos. . . . . . . . . . . . . . . . . . . . . 21

EVENT SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

BTIMELINE SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

CT/D SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

DGO FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

EGO LAST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

FLOG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

GBOOKMARK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Copying recorded video . . . . . . . . . . . . . . . . . . . . . . . . . 26

Inserting recording media . . . . . . . . . . . . . . . . . . . . . . . . . 26

BCopying live videos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

CCopying a playback video . . . . . . . . . . . . . . . . . . . . . . . . . 27

DPlaying back copied videos . . . . . . . . . . . . . . . . . . . . . . . . 27

Setting the security lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Configuration and function of the Menu settings . . . . . 29

LIVE settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Setting the OSD and OSD CONTRAST . . . . . . . . . . . . . . . 31

A BSetting the SEQUENCE and SEQUENCE-DWELL TIME . 31

CSetting the EVENT BEEP . . . . . . . . . . . . . . . . . . . . . . . . . . 31

DSetting a CHANNEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

EAlarm input output settings . . . . . . . . . . . . . . . . . . . . . . . . 32

FSetting the MON2 (Monitor2)-OUT. . . . . . . . . . . . . . . . . . . 33

RECORD settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Setting the RESOLUTION . . . . . . . . . . . . . . . . . . . . . . . . . . 35

BSetting a CHANNEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CSetting the TIMER SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

SYSTEM settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

Setting the DVR ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

BDESCRIPTION confirmation . . . . . . . . . . . . . . . . . . . . . . . . 37

CSetting the LOAD DEFAULT. . . . . . . . . . . . . . . . . . . . . . . . 37

DSetting an ADMIN PASSWORD . . . . . . . . . . . . . . . . . . . . . 38

ESetting the USER PASSWORD. . . . . . . . . . . . . . . . . . . . . . 39

FSetting a NETWORK PASSWORD . . . . . . . . . . . . . . . . . . . 39

GSetting the DATE FORMAT. . . . . . . . . . . . . . . . . . . . . . . . . 40

HSetting the CLOCK SET . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

ISetting the RS-485 SET . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

JSetting the PTZ CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 40

KSetting the LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

LSetting a REMOTE CONTROL ID . . . . . . . . . . . . . . . . . . . . 41

NETWORK settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Setting the PORT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

BSetting a CLIENT ACCESS . . . . . . . . . . . . . . . . . . . . . . . . . 42

CSetting the BANDWIDTH SAVING . . . . . . . . . . . . . . . . . . . 42

DSetting the NETWORK TYPE . . . . . . . . . . . . . . . . . . . . . . . 43

ESetting the DDNS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

FSetting the SEND E-MAIL . . . . . . . . . . . . . . . . . . . . . . . . . . 45

HDD SET settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Setting the OVERWRITE. . . . . . . . . . . . . . . . . . . . . . . . . . . 46

BFORMAT settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

CSetting the auto delete function. . . . . . . . . . . . . . . . . . . . . 47

SERVICE settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Setting the SAVE SETUP TO A USB . . . . . . . . . . . . . . . . . 48

BSetting the LOAD SETUP FROM A USB . . . . . . . . . . . . . . 48

CDisplays the hard disk information . . . . . . . . . . . . . . . . . . 48

Operations using the Network . . . . . . . . . . . . . . . . . . . . .49

Connection and settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Operating environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Installing "Sanyo DVR Utility 2000S" . . . . . . . . . . . . . . . . . . . 49

To uninstall the software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Connecting to this unit . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Main screen structure and function of each part . . . . . .52

Function of the operation panel. . . . . . . . . . . . . . . . . . . . . . . 53

Main screen basic operations . . . . . . . . . . . . . . . . . . . . .54

Switching the display mode of the screen . . . . . . . . . . . . 54

BRecording live video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

CFreezing the live video . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

DThe audio is output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

ESaving images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

FOperating the PTZ camera . . . . . . . . . . . . . . . . . . . . . . . . . 57

Search mode operations. . . . . . . . . . . . . . . . . . . . . . . . . .58

Searching and playing recorded video . . . . . . . . . . . . . . . 59

BBacking up DVR recorded video . . . . . . . . . . . . . . . . . . . . 60

Setup menu settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

General settings (General) . . . . . . . . . . . . . . . . . . . . . . . . . 61

BCamera designation settings (Site) . . . . . . . . . . . . . . . . . . 62

CEvent settings (Event). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

DEvent log search, view, save (Log View). . . . . . . . . . . . . . 63

ERecord settings (Record) . . . . . . . . . . . . . . . . . . . . . . . . . . 64

FDisk settings (Disk). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

GVersion information (About). . . . . . . . . . . . . . . . . . . . . . . . 64

Part names of the remote control . . . . . . . . . . . . . . . . . .65

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66

Safety precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user’s authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION

This product employs a Laser System. To ensure proper use of this product, Please read this owner's

manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service

center. Use of controls, adjustments or the performance of procedures

other than those specified herein may result in hazardous radiation exposure.

To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

Declaration of Conformity

Model Number : DSR-2016 Trade Name : SANYO Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street, Chatsworth, California

91311

Telephone No. : (818) 998-7322

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference,and (2) this device must accept any interference received,

including interference that may cause undesired operation.

For the customers in Canada

This class B digital apparatus complies with Canadian ICES-003.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the

manufacturer. Discard used batteries according to the manufacture’s instructions.

FOR CALIFORNIA, U.S.A. ONLY

This product contains a CR Coin Lithium Battery which contains Perchlorate Material - special handling may apply.

See www.dtsc.ca/gov/hazardouswaste.perchlorate.

Licensed Under U.S. Patent No. 4,974,088

Please note:

Your SANYO product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!

This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world.

FOR RUSSIAN USERS

This product certified by official certification company which is authorized by Russian Federation.

ДЛЯ ПОЛЬЗОВАТЕЛЕЙ РОССИЯ

Данная продукция сертифицирована официальным органом по сертификации Российской Федерации.

Safety precautions

These precautions must be followed for safety reasons.

Warning

b Do not use if the unit emits smoke,

strange sounds are heard or odor is emitted.

Continued use may cause electrocution and/ or fire. Immediately remove the power plug

Remove the power plug from the outlet.

from the outlet. Once the unit stops emitting smoke, consult the dealership where this unit was purchased or factory shop for repairs.

Do not attempt repairs on your own.

b Make sure the power cable is not damaged.

• Always use the power cable supplied with the unit.

• Do not place heavy objects on the power cable or place the power cable near

Prohibited

heating equipment. Also, do not bend the power cable forcefully, work upon or staple it.

A damaged power cable may result in fire and/or electrocution.

• Should the power cable become damaged it must be replaced by the dealership where this unit was purchased or factory shop.

b Make sure there is no dust accumulation on the

power plug or the outlet.

• Dust accumulation may result in a short-circuit and heat generation and cause fire.

• Be especially careful when using an outlet

Prohibited

situated in a room exposed to high humidity, condensation and/or dust, or in a kitchen.

• Periodically remove the power plug from the outlet and clean any dust and dirt between the plug and the outlet.

b Caution when connecting the power cable

• Connect the power plug directly with the outlet. Faulty connection may result in heat generation and cause fire.

• Do not use the power cable while it is tied in a bundle. This may result in heat generation and cause fire.

• When using the extension cord supplied, make sure the power consumption of the connected unit does not exceed the electrical rating of the extension cord. Higher power consumption may result in heat generation and cause fire.

Prohibited

b Disassembly prohibited

• Do not place your hand inside this unit as this may cause fire and/or electrocution.

• Consult the dealership where this unit was

Disassembly prohibited.

purchased or factory shop for diagnostics, adjustments, and repairs.

b Do not place any foreign objects inside the unit.

• Do not insert or push in any metal or combustible objects through openings such as air ducts. This may cause fire and/ or electrocution.

Prohibited

• In the event that a foreign object is inside the unit, turn off and unplug the unit. Consult the dealership where this unit was purchased or factory shop. Continued use may result in fire and/or electrocution.

Remove the power plug from the outlet.

b Do not place a container holding

water or other liquids above the unit when it is connected to power.

In the event that water gets inside the unit, turn off and unplug the unit. Consult the dealership where this unit was purchased or factory shop.

Continued use may result in a fire or electrocution.

Water is prohibited

Remove the power plug from the outlet.

b Do not allow the unit to get wet.

• This unit is not waterproof. Do not expose the unit to water. This may cause fire and/ or electrocution.

Do not use in a bath or shower room.

• In the event that the internal components have been exposed to water, turn the power off and remove the power plug from the outlet. Consult the dealership where this unit was purchased or factory shop. Continued use may cause electrocution and/or fire.

Water is prohibited

Exposing to water is prohibited

iii

Safety precautions

Warning

b Do not use during thunder/thunder storms.

Do not use during thunder/thunder storms. Never touch the connection cable during thunder/thunder storms. This may cause electrocution.

b Do not place in an unstable position.

• Doing so may cause accidents and/or breakdowns through falling or toppling.

• In the event that the unit has been dropped or the casing has been damaged, turn the power off and remove the power plug from the outlet. Consult the dealership where this unit was purchased or factory shop.

Continued use may cause electrocution and fire.

b Do not expose to shock or vibration.

Stored data may be damaged or lost through hard-disk breakdowns caused by shock/ vibration.

b Do not use this unit in areas where it is exposed

to the possibility of explosion.

Do not use this unit in areas where explosive and/or flammable gases are present. This may cause fire and/or explosion.

Contact prohibited

Prohibited

Remove the power plug from the outlet.

Prohibited

Caution

b Do not pull on the power cable when removing

the power plug from the outlet.

Hold the power plug when disconnecting the power cable from the outlet. Pulling on the power cable may damage the cord. This may cause fire and/or electrocution.

b Do not touch the power plug with wet

hands.

Doing so may result in electrocution.

b Do not sit on.

Doing so may cause the unit to fall, be damaged and/or result in injury.

b Make sure the cables are connected properly.

Connect and install the power cable and connection cable very carefully. Tripping over the cable may result in the unit capsizing or falling and cause injury.

b Do not place heavy objects on connected units.

Doing so may affect the stability of the unit and cause it to fall which may result in injury. Doing so may also damage the unit depending on the weight of the object.

b Shipment and portability

• Never move this unit while the power is turned on.

• When shipping, remove the power plug from the outlet, confirm that the connection cable has been removed, and store in original packaging. Ship using a method that causes the least amount of shock and/or damage to this unit. Also, do not drop this unit.

Prohibited

Wet hands

prohibited

Prohibited

Remove the power plug from the outlet.

b Maintenance when the unit is going to remain

unused for long periods of time

Remove the power plug from the outlet. Carrying out maintenance without removing the power plug may cause electrocution.

Remove the power plug from the outlet.

Safety precautions

Caution

b Cleaning the internal components

Consult the dealership where this unit was purchased or factory shop for cleaning internal components. Leaving the unit unused for long periods of time may attract dust to the internal components, which in turn may cause fire and/or breakdowns.

b Do not block the cooling fans or air ducts.

• This unit is equipped with air ducts and cooling fans in order to assist the ventilation of hot air produced by the hard disk drive.

Placing covers, placing in a case, or placing inside bookcases may cause heat build up, and may result in fire and/or electrocution.

When the unit is set up in a rack, leave open space on all sides.

• Leave 1 cm or more of space above and below.

• Leave 5 cm or more of space on both sides and on the rear.

b Do not expose to extreme temperatures or

humidity changes.

• Do not place in areas where the unit will be exposed to extreme temperatures (±10 degrees C per hour) or humidity changes.

b Cautionary points on condensation

Droplets may form on the outside when very cold water is poured into a cup. In the same way, droplets may form around the internal components of this unit. This is called condensation.

Do not use this unit if condensation has formed.

Using this unit while condensation is formed may cause breakdowns. In the event of sudden sharp temperature changes, turn off the power and do not use this unit until the temperature of the room where it is positioned stabilizes (about 2 hours).

Condensation will not occur while the power is turned on.

Prohibited

When condensation is likely to occur ...

Use the unit after turning the power off and leaving it for 1~2 hours.

Prohibited

b Points on unit positioning

This unit is constructed using precision electronic parts. Avoid placing it in areas described below as this may cause faulty operation and/or breakdowns.

• In direct sunlight

• In places exposed to water

• In the vicinity of cooling and heating units or humidifiers

• Near the air conditioner where the unit is exposed to cool air

• Dusty areas

• Areas that contain fire hazards

• Areas that contain magnetic items

• In the vicinity of volatile substances

• Areas where the unit will be exposed to constant vibration (in trains, cars, etc.)

Prohibited

Safety precautions

Follow the points outlined below for proper use

bBack up battery.

• This unit has got a built-in lithium battery used to back up the clock function. The battery continues to operate the clock even when there is a power disruption.

• The life expectancy of the battery is approximately 2 years. If the battery runs out or leaks, the clock resets when the power is turned off. When the power is turned back on (or when rebooted), a warning message to replace the battery is displayed on the monitor screen. Consult the dealership where this unit was purchased or a "Repair Service Center".

Battery fluid leaks

In the event that the battery fluid has leaked rinse hands/ clothes thoroughly with water.

Loss of eyesight may result if battery fluid enters the eyes. Do not rub the eyes. Immediately rinse with clean water and consult a physician.

When disposing of this unit

Consult the dealership where this unit was purchased for information concerning the disposal of the lithium battery.

bIf unused for a lengthy period of time

Remove the power plug from the outlet. Remember to occasionally turn the power on in order to maintain correct function.

bPre-confirm important recording

assignments

Recording and/or playback functions may be unavailable due to hard-drive or connecting unit failures. Always confirm that recording can be carried out successfully before carrying out important recording assignments. The recorded content cannot be guaranteed.

It is recommended to periodically back up or mirror data in order to prevent the loss of data in the event of breakdowns, recording faults or accidents.

bMaintaining this unit

Turn the power off and remove the power plug from the outlet. Wipe away any dust using a soft cloth.

When the stains are hard to remove... Soak a cloth in water with diluted neutral detergent and wring it. Wipe the stain with the moistened cloth and finally dry off with a dry cloth.

CAUTION:

• Do not use paint thinner, benzine, or any other alcohol based agents for cleaning. The exterior may deteriorate or the paint may wear off.

• Follow the instructions supplied on the packaging of the chemical cleaning agent.

• Do not spray volatile substances, such as insecticides, etc. onto the unit. Also, avoid extended contact with rubber or vinyl products.

This may cause exterior damage or wear the paint off.

bCopyright information

• This manual and software are copyrighted to SANYO Electric Co., Ltd.

• Microsoft, Windows and Internet Explorer are trademarks or registered trademarks of Microsoft USA in the USA and in other countries.

• Intel and Pentium is a trademark or registered trademark of Intel USA in the USA and in other countries.

• Brand and product names used in this manual are the trademarks or registered trademarks of their respective companies.

Except for personal use, copyright law prohibits the use of recorded copyrighted images without the permission of the copyright holder.

bPersonal data protection

Images or footage recorded by the camera video system in which people are captured and can be identified are considered to be personal information and fall within the scope of the Personal Data Protection Law. It is the responsibility of the user to operate the system in accordance with the above law.

Main Features

Accessories

• Real time monitoring at 800 IPS (PAL) / 960 IPS (NTSC)

• Maximum recording speed at 200 IPS (PAL) / 240 IPS (NTSC)

• 4ch audio recording

• Remote surveillance via network

• VGA video output

• Comes with IR remote control unit and DVR utility software

• Built-in CD-RW drive

Main parts replacement timings

Continued use of this unit in a 25°C environment may result in wear and deterioration of the parts of the unit. We recommend you replace the following parts according to the timings listed below. The replacement timings listed are approximate and do not guarantee the performance of the part in question.

Check that all the parts shown below are supplied.

1 Power cable (×2)

2 Remote control

3 HDD mounting bracket (×2)

4 HDD fixing screw (×8)

5 Mounting bracket screws (×8)

6 IDE cable

7 HDD power branch cable

8 CD-ROM

• Instruction Manual (Digital Video Recorder)

b Hard disk: 2 years (25°C environment)

The life expectancy of each part depends on the environment in which the unit is used. However, the head and motor are particularly prone to wear and deterioration. Therefore, writing errors are more likely to occur after two years of use.

b Cooling fan: 3 years (25°C environment)

Cooling fan failure causes higher internal temperatures which may result in a faulty hard disk. Periodically check whether the cooling fan is working properly.

Cooling fan

Memo: This unit is equipped with two cooling fans on the

right and at the rear. The cooling fan on the right may be replaced.

b Battery: 2 years (25°C environment)

Mounting the hard disk

A hard disk may not be installed at the time of purchase. If no hard disk is installed, consult the dealership where the unit was purchased for purchase and installation.

Make sure the unit is turned off before installing the hard disk.

Unfasten the cover of the unit.

Set the mode of the hard disk to be installed to "Master". For more information, read the hard disk installation manual.

The hard disk is a precision instrument. To avoid damage, handle the hard disk with care and do not expose it to shock.

Do not block the ventilation holes and do not allow the cooling fan to stop. Doing so may cause heat build up and may shorten the life expectancy of the hard disk.

G This unit is designed to be positioned horizontally. Do

not position vertically.

G Do not expose to shock or vibration and do not

transport while power is turned on.

Always turn the power off when moving in and out of racks or other shelves.

G Do not remove the power plug while recording or

playing images back.

Warning

Fix the supplied HDD mounting brackets to the

hard disk using the supplied mounting bracket screws (A).

Connect the supplied IDE cable (B) and power

cable (C) to the hard disk and fix the hard disk to the unit using the supplied HDD fixing screws (D).

Black

G Do not move the unit for approximately 30 seconds

after turning the power off.

The hard disk continues to rotate for a short duration after the power has been turned off. The unit is further susceptible to damage through shock and vibration during that period. It is imperative that you do not move the unit during that time.

G Do not expose to shock or vibration.

Avoid placing this unit directly on the floor. Make sure that the four stands attached to the base of this unit are used when placing it on the floor.

G Always use the original packaging (packaging

supplied at the time of purchase), when shipping the unit.

Make sure you use the packaging materials supplied at the time of the original purchase when shipping the unit or a single internal component of the unit. Select a shipping method that will cause the least amount of shock to the unit during shipping.

Consult the dealership where this unit was purchased for hard disk replacement.

• The hard disk is vulnerable to static electric shocks. Take appropriate measures to prevent exposure to static electricity.

• Unpackaged drives should be placed horizontally with their base plate facing upwards on top of a soft cloth. Exposing

Blue

the hard disk to shocks and vibration may cause breakdowns.

• Do not expose the drive to shocks and/or vibrations when removing/tightening the screws at the time of hard disk replacement. Firmly tighten the screws after replacement.

Names and functions of parts

Front panel

4 5 6 7 8 9FGHIJ L M

1 Power button and indicator ( )

2 USB terminal (USB) (Exclusively for 2.0) (P26)

To save video, connect a USB memory.

3 CD drive

To save video, insert a CD-R/RW. To open and close the insert tray, open the panel and

press the button.

4 LAN indicator (LAN)

The indicator blinks when the unit is connected and used through the LAN cable.

5 Alarm indicator (ALARM)

The indicator lights during an alarm recording or when an alarm is set off.

6 Hard disk drive indicator (HDD)

The indicator lights when the hard disk is being accessed.

7 Recording indicator (CH1 - CH16)

The channel number being recorded lights.

8 Record/Stop button (REC/STOP) (P16)

Starts/Stops the recording of the monitored live image displayed.

9 Automatic camera scrolling button (SEQ) (P13)

Automatically switches through and displays the images of each live.

F Quad-screen display button (QUAD) (P13)

The monitor video is displayed on quad-screen.

G Multi button (MULTI) (P13)

The monitor video is displayed on multi-16 or multi-9 screen.

H Mark/Copy button (MARK/COPY) (P26)

Switches to image saving mode.

I Search button (SEARCH) (P22)

Switches to recorded-images searching mode.

J Pan/Tilt/Zoom button (PTZ) (P14)

Operates the Pan/Tilt/Zoom/Focus mode of the dome camera connected to the RS-485 control terminal.

K Channel selection buttons (1 - 16) (P12)

The video of the selected channel is displayed on single-screen.

Also used to enter a password.

L Menu button (MENU) (P9/30)

Displays the settings menu screen and switches to setting mode.

M Exit/Stop button (EXIT/STOP) (P17)

During settings: Returns to the previous screen. During playback: Interrupts playback operation.

Memo: A security lock can be set by holding the button

down. (P28)

N Control button

Setting in progress

(Cursor operation)

Playback in progress

Skip button (SKIP):

The player jumps one minute forward.

Replay button (REPLAY):

The player jumps one minute backward.:Moves the cursor downward.

button:

The player fast rewinds.

button:

The player fast-forwards.

button:

The player displays a still image.

Plays the image selected during the image search operation.

Moves the cursor upward.

Changes the settings value or moves the cursor to the left.

Changes the settings value or moves the cursor to the right.

ENTER :

Sets the selected item or displays the settings screen.

Names of each part and connections

Rear panel

Basic connections

• Do not turn this unit on before all the connections are complete. Read the instruction manual of each unit carefully.

• Make sure each unit is connected properly as faulty connection may result in the unit emitting smoke and/or being damaged.

• Feed additional units with the same power source. Stored data may be lost.

Camera

(Sold separately)

Video monitor

(Sold

separately)

Video monitor

(Sold

separately)

56789FGH IJK

Speaker with

built-in amplifier

(Sold separately)

1 Video input terminal (VIDEO IN/LOOP OUT: CH1 -

CH16)

2 Video output terminal (S-VIDEO)

3 Monitor 2 video output terminal (MON2)

4 Video output terminal (MAIN)

5 Audio input/output terminal (AUDIO IN: CH1 - CH4/

OUT)

6 VGA (Video Graphics Array) output terminal

Connects to the PC VGA monitor.

7 External sensor terminal (ALARM IN: 1-16)

8 Network terminal (LAN: P5)

POWERMODEAUTO

Monitor

(Sold

separately)

G System changeover switch (SWITCH)

TERMINATE: RS-485 termination switch (P11) RSV: For maintenance purposes. VGA: Monitor selection switch (P9) PA L: Television mode (PAL/NTSC) switching switch (P9)

H Alarm output terminal (ALARM OUT: 1-4)

I Cooling fan (P1)

J Power switching switch (115V/230V)

Switch according to the voltage used in the region where this unit is installed.

K Power socket

9 RS-232C terminal (RS-232C)

For maintenance purposes.

F RS-485 control terminal (RS-485/422: P14)

Names of each part and connections

Network connection (LAN)

LAN connection

b Using the switching hub

Use a 10BASE-T/100BASE-TX CAT 5 LAN cable. When controlling the network, connect to hubs such as the

switching hub using an Ethernet cable.

Camera

(Sold separately)

Computer

Ethernet cable

(Straight cable)

POWERMODEAUTOMENU

Monitor

(Sold separately)

Switching hub

b Without using a switching hub

Camera (Sold separately)

Internet (DHCP, ADSL) connection

Connect to the Internet using a router and the like. When connecting to an ADSL modem or other device, read

the instruction manual of the device for information on how to connect.

Camera

(Sold separately)

Internet

Computer

Ethernet cable

(Straight cable)

POWERMODEAUTOMENU

Monitor

(Sold separately)

Memo: The type of network must be set on the NETWORK

screen. (P42)

Router or ADSL modem

and the like

POWERMODEAUTOMENU

Monitor

(Sold separately)

Cross type

Computer

Names of each part and connections

Connecting to the RS-485 control terminal

Remote systems such as system controllers and PTZ cameras are connected to the RS-485 control terminal. Check the manufacturer of the units to be connected and connect the units to the appropriate terminal signals (A/B).

1234

1 A (SANYO SSP)

2 B (SANYO SSP)

3 A (EXCEPT SANYO)

4 B (EXCEPT SANYO)

To connect a Sanyo PTZ camera or system controller

To connect a third-party camera

If a system controller is connected

This unit can be operated through the controller.

System controller

Memo: • The setting of the RS-485 screen on the system

setting is necessary when a system controller is connected. (P40)

• Refer to the System controller’s instruction manual for more information about the operation method.

If a camera is connected

If a PTZ camera equipped with a RS-485 control terminal is connected, the camera can be directly operated through this unit.

Memo: The settings of the PTZ CONTROL screen and

RS-485 screen on to system setting are necessary when a camera is connected. (P14, 40)

Switching the power on / off

Switching the power on

Connect the power cable to the outlet.

Turn on the electricity, the power indicator lights in orange (standby).

Press the power button.

The power indicator changes to green (running) and initialization starts.

During initialization the message "INITIALIZING..." and the firmware version are displayed on a "SANYO" logo screen.

Once the initialization is complete, live videos are displayed on multi-16 screen.

INTIALIZING...

Ver: SNXXXX.XX.XXXX(YYYYMMDD)

212 53

Switching the power off

Press the power button.

The password entering screen is displayed.

Enter the ADMIN PASSWORD using the channel

selection buttons.

The factory default password is "1111". For security reasons, make sure you change the default

ADMIN PASSWORD. (P38)

1 10

Press the ENTER button.

The SHUTDOWN confirmation screen is displayed.

PASSWORD

* * * *

- - - -

CH1

•

2007/05/03 09:04:54

NO VIDEO

CH3

NO VIDEO

CH7

NO VIDEO

CH11

NO VIDEO

CH15

NO VIDEO

CH4

NO VIDEO

CH8

NO VIDEO

CH12

NO VIDEO

CH16

CH1

NO VIDEO

CH5

NO VIDEO

CH9

NO VIDEO

CH13

NO VIDEO

CH2

CH6

CH10

CH14

Do not press the power button during initialization. This may result in data loss.

Select "CONFIRM" with the control button (}~).

SHUTDOWN

CANCEL CONFIRM

Press the ENTER button.

The power shuts down and the power indicator turns orange.

Pre-operation preparation

Screen display

Upon turning the power on live video is displayed on the multi-16 screen.

• The screen display can be hidden except for the recording screen display. (P31)

b Example of multi-16 screen b Example of single-screen

12 634 5

2007/05/03 09:04:54

CH3

CH11

CH15

CH4

CH12

CH16

CH1

CH9

CH13

CH2

CH6CH5 CH7 CH8

CH10

CH14

1 Operation display

: Displayed during live video sequencing.

: Displayed during alarm output.

: Displayed when the alarm output is set to DISABLE.

: Displayed during remote operation by PC.

2 Remote control display (P41)

: Displays the remote control ID currently in

operation. If no remote ID is set the message "A(all)" is displayed.

3 Alarm input display

: Displayed during motion or external alarm input

(ALARM IN).

4 Security lock display

: Displayed when setting the security lock. (P28)

5 Hard disk used capacity display

Displays the amount of recording on the hard disk from 0-99%. When the disk is full, "99%" changes to "FULL".

When the recording settings are set to overwrite and the hard disk is full, 99% changes to which represents overwriting mode.

12 634 5

CH1 C

2007/05/03 09:04:54

6 Date and time display

This unit manages the recorded videos according to their date and time. Make sure the correct date and time are set in the CLOCK SET. (P9)

7 Camera channel display

CH1 - CH16 Select display/hide channel in "OSD settings" in "LIVE

settings". (P31)

8 Recording display

Factory default settings start continuous recordings (C) automatically once the power is turned on. Change the recording mode using the menu settings. (P35)

C: Recording in the continuous mode (CONTINUOUS) R: Recording in the real time mode (When pressing the

REC/STOP button)

M: Recording in the motion detection mode (MOTION) A: Recording in the ALARM IN detection mode (ALARM)

• If a live video is disconnected, the message "VIDEO LOSS" is displayed on the monitor.

• If a video signal is not connected to the video input terminal, the message "NO VIDEO" is displayed on the monitor.

Pre-operation preparation

Setting the television system and the monitor

output

If the television system of the camera to be connected and the type of monitor differ, live videos cannot be monitored on the normal screen. Check the specifications of the equipment to be connected and set the system changeover switch on the rear panel.

• Do not forget to turn off the power when adjusting the settings.

b Matching the television system of the camera

(PAL)

Up: When using a NTSC camera Down: When using a PAL camera

Cannot be used when PAL and NTSC system are mixed.

2 3

Setting the clock (CLOCK SET)

Press the MENU button.

The PASSWORD input screen is displayed.

PASSWORD

• To return to the previous screen, press the EXIT/ STOP button.

Enter the "ADMIN PASSWORD" using the channel

selection buttons.

The MAIN MENU screen is displayed.

•"1111" is the factory default setting password.

- - - -

CH1

2007/05/03 09:04:54

b Selecting the type of monitor (VGA)

Up: When connecting the general monitor to the video

output terminal

Down: When connecting a PC monitor to the VGA

terminal

POWERMODEAUTOMENU

Generic monitors PC monitors

The VGA terminal and the video output terminal cannot be used simultaneously.

1 10

PASSWORD

* * * *

- - - -

CH1

MAIN MENU

RECORDLIVE SYSTEM

HDD SETNETWORK SERVICE

2007/05/03 09:04:54

Pre-operation preparation

Press the control button (~) twice and select the

"SYSTEM", press the ENTER button.

The SYSTEM settings screen is displayed.

SYSTEM

DVR ID DVR DESCRIPTION LOAD DEFAULT ADMIN PASSWORD USER PASSWORD NETWORK PASSWORD DATE FORMAT YYYY/MM/DD CLOCK SET RS485 SET PTZ CONTROL LANGUAGE ENGLISH REMOTE CONTROL ID 00

Select "DATE FORMAT" using the control button

({|) and select the date display format using the control button (}~).

• YYYY/MM/DD (Example: 2007/03/15)

• MM/DD/YYYY

• DD/MM/YYYY

Select "CLOCK SET" using the control button ({|)

and press the ENTER button.

•YYYY-MM-DD (Example: 2007-03-15)

• MM-DD-YYYY

• DD-MM-YYYY

The CLOCK SET screen is displayed.

CLOCK SET

D.S.T./SUMMER TIMED.S.T./SUMMER TIME OFF

2007/03/15 10:20:30

Select "D.S.T./SUMMER TIME" using the control

button ({|), select the appropriate daytime saving time zone using the control button (}~).

If choosing EU or OTHERS set the applicable conditions.

CLOCK SET

D.S.T./SUMMER TIME USA

2007/03/15 10:20:30

b OFF

Daylight saving is not set.

b USA

Applies the USA daylight saving time.

b EU

Applies the EU daylight saving time.

CLOCK SET

D.S.T./SUMMER TIME EU

GMT AREA +00:00

2007/03/15 10:20:30

1 Select the "GMT AREA" using the control button

({|).

2 Set the time difference with the standard time using

the control button (}~).

b OHTERS

If the time zone is neither USA nor EU, set the start and end date of the daylight saving period.

CLOCK SET

D.S.T./SUMMER TIME OTHERS

BEGIN MAR 1st SUN 00H END SEP 1st SUN 00H

2007/03/15 10:20:30

1 Select "BEGIN" using the control button ({|) and

press the ENTER button.

2 Select the item using the control button (}~ ),

select the setting value using the control button ({|).

3 Press the ENTER button once the daylight saving

start date is set.

4 Set the daylight saving end date using the same

procedure.

Select the display date and time using the control

button ({|).

CLOCK SET

D.S.T./SUMMER TIME OTHERS

BEGIN MAR 1st SUN 00H END SEP 1st SUN 00H

2007/03/15 10:20:30

Select the item using the control button (}~), set

the date and time using the control button ({|) and press the ENTER button.

The update time confirmation screen is displayed. After you confirm the screen, select "CANCEL" or

"CONFIRM" using control button.

CLOCK SET

CANCEL CONFIRM

The date and time displayed on the update time confirmation screen takes daylight saving into consideration.

Pre-operation preparation

Select "CONFIRM" using the control button (}~)

and press the ENTER button.

The unit automatically restarts, the initializing screen is displayed.

Once the initialization is complete and the live screen is displayed, the displayed date and time are updated.

INTIALIZING...

Ver: XXXXXX.XX.XXXX(YYYYMMDD)

2007/05/03 09:04:54

Setting the language (LANGUAGE)

Follow steps 1 to 3 of the CLOCK SET procedure

Select "LANGUAGE" using the control button ({|)

and select the display language using the control button (}~).

Once a language has been selected the display language changes.

SYSTEM

DVR ID DVR DESCRIPTION LOAD DEFAULT ADMIN PASSWORD USER PASSWORD NETWORK PASSWORD DATE FORMAT YYYY/MM/DD CLOCK SET RS485 SET PTZ CONTROL LANGUAGE ENGLISH REMOTE CONTROL ID 00

NO VIDEO

CH1

NO VIDEO

CH5

NO VIDEO

CH9

NO VIDEO

CH13

NO VIDEO

CH2

CH6

CH10

CH14

NO VIDEO

CH3

NO VIDEO

CH7

NO VIDEO

CH11

NO VIDEO

CH15

NO VIDEO

CH4

NO VIDEO

CH8

NO VIDEO

CH12

NO VIDEO

CH16

b Correcting the set time

When a new time earlier than the previous recording time is set, the recording data that will be erased, showed in range

A, is displayed on the clock update confirmation screen.

Confirm the time before selecting "CONFIRM" as any video data recorded after the set time will be erased.

CLOCK SET

CANCEL CONFIRM

Caution: If you update to new T/D, recorded data between new and rec-end T/D will be deleted.

New T/D 2007/ 5/11 13:43:39 Rec-end T/D 2007/ 5/11 13:53:45

Set time

Language selection:

ENGLISH, 日本語 , DEUTSCH, Francais, ESPANOL, ITALIANO, ipllXTV ìRàX, 中文（繁體） , POLSKI, CESKY, óçhHBjlXV LRTX, Româna, Srpski, SVENSKA,

ภาษาไทย

Setting the RS-485 termination switch (SANYO

SSP side)

If multiple devices are connected terminator settings are necessary at both ends.

• When multiple devices are connected, Make the termination switch "ON" on the first and last device you connected.

• When multiple devices are connected, Make the termination switch "OFF" except the first and last devices that you connected.

If the termination switch is not set, the correct data will not be delivered to each unit.

System controller

Previous recorded time

Digital video recorder

Termination switch ON

234

RS485 Termination switch (TERM) OFF

RS485 Termination switch (TERM) ON

Monitoring the camera videos

CD B

Single-screen display

Displays the video of the camera specified using the channel selection button (1 - 16) on single-screen.

Example: Displaying camera 2 on single-screen

Press "2" on the camera selection button.

The video of camera 2 is displayed on single-screen.

CH2

2007/05/03 09:04:54

Quad-screen display

Displays the 4 cameras video connected at once.

Press the QUAD button.

The videos of cameras 1 - 4 are displayed on quad-screen.

2007/05/03 09:04:54

Press the QUAD button again.

CH1 C

CH3 C

The videos of cameras 5-8 are displayed on quad-screen.

Each time pressing the QUAD button, The video of the camera changes as the quad-screen.

CH2 C

CH4 C

0201

0403

1413

1615

0605

0807

1009

1211

Monitoring the camera videos

Multi-screen display

Displays the videos of 16 or 9 cameras simultaneously.

Press the MULTI button.

The videos of camera 1 - 16 are displayed on a multi-16 screen.

03 04

07 08

Press the MULTI button again.

01 02

05 06

09 10 11 12

13 14 15

The screen switches to a multi-9 screen, the videos of camera 1 - 9 are displayed.

Camera sequencing

Automatically displays the channel in sequence on a single or quad-screen.

Press the SEQ button while using the single or

quad-screen display.

The cameras automatically switch in sequence starting with the channel of the camera being displayed. If there is an audio input, the audio also switches in channel sequence order.

Sequence display

CH2

2007/05/03 09:04:54

• When using single-screen display

07 08 09

0302

Pressing the button again switches the screen in turn from a multi-9 screen (2 patterns) to a multi-16 screen.

03 04

0302

01 02

05 06

09 10 11 12

13 14 15

07 08 09

• When using quad-screen display

0201

0403

1413

1615

0605

0807

1009

1211

Memo: • The sequence interval from one camera video to

another can be set. (P31)

• Automatic camera sequencing is not available when using multi-9 or multi-16 screen.

01 02

Press the SEQ button once operations are

1211

complete.

The sequence mode is cancelled.

Operating the PTZ camera

Pan/Tilt, Zoom/Focus operations are available from this unit when a PTZ camera is connected to the RS485 control terminal.

Connection

Connect the RS-485 control terminal and the camera using a twisted pair cable.

Refer to "Connecting the RS-485 control terminal (P6)".

Settings

Press the MENU button (the MAIN MENU is

displayed) and select "SYSTEM" using the control button (}~).

MAIN MENU

RECORDLIVE SYSTEM

HDD SETNETWORK SERVICE

DVR ID DVR DESCRIPTION LOAD DEFAULT ADMIN PASSWORD USER PASSWORD NETWORK PASSWORD DATE FORMAT YYYY/MM/DD CLOCK SET RS485 SET PTZ CONTROL LANGUAGE ENGLISH REMOTE CONTROL ID 00

SYSTEM

• A password is requested when pressing the MENU button. Enter the ADMIN PASSWORD. (P38)

Place the cursor on "PTZ CONTROL" and press the

ENTER button.

The PTZ screen is displayed.

PTZ

DATA SPEED 9600 CHANNEL 1 PROTOCOL --- ADDRESS 1

Point the cursor to "DATA SPEED" and set the

communication speed.

The set speed is applied to all channels except for SANYO protocol.

Set the communication speed for the SANYO protocol using RS-485 SET. (P40)

Point the cursor to "CHANNEL", specify the

channel and set the "PROTOCOL" and "ADDRESS". PROTOCOL: Selecting the type of protocol ADDRESS: Camera ID (0 - 63)

When connecting multiple cameras, set the same protocol for all cameras except for those cameras connected with SANYO protocol.

Operation

Select the number of the dome camera connected

using the camera selection button.

Press the PTZ button.

The control screen is displayed.

Controlling the camera

Control functions available differ according to the camera model.

IRIS/TOUR/SEQUENCE

PAN/TILT

ZOOM/FOCUS

b Pan/Tilt operations

1 Select "PAN/TILT" using the control button ({|)

and press the ENTER button.

2 Adjust the tilt position using the control button ({|)

and adjust the pan position using the control button (}~).

3 To perform automatic panning press the ENTER

button.

• The following message is displayed on the screen.

Up/Down key: Tilt Up/Down Left/Right key: Pan Left/Right Enter key: Auto Pan

b Zoom/Focus operations

1 Select "ZOOM/FOCUS" using the control button

({|) and press the ENTER button.

2 Adjust the zoom using the control button ({|) and

adjust the focus position using the control button (}~).

3 To activate the auto focus press the ENTER button.

• The following message is displayed on the screen.

Up/Down key: Zoom In/Out Left/Right key: Focus Near/Far Enter key: Auto Focus

2007/05/03 09:04:54

Press the EXIT/STOP button once the settings are

complete.

Operating the PTZ camera

b Iris / Tour / Sequence operations

1 Select "IRIS/TOUR/SEQUENCE" using the control

button ({|) and press the ENTER button.

2 Adjust the aperture using the control button (}~). 3 To perform tour operations press the control button

({), to stop tour operations press the ENTER button.

4 To perform sequence operations press the control

button (|), to stop sequence operations press the ENTER button.

• The following message is displayed on the screen.

Up/Down key: Tour ON/Sequence ON Left/Right key: Iris Close/Open Enter key: Tour/Sequence OFF

b Camera menu settings

1 Select "MENU" using the control button ({|) and

press the ENTER button.

2 Select a menu using the control button ({|) and

select a setting value using the control button (}~).

3 To switch to the next screen or validate a setting

value press the ENTER button.

• The following message is displayed on the screen.

Up/Down key: Cursor Up/Down Left/Right key: Cursor Left/Right Enter key: Enter

Press the EXIT/STOP button once operation are

complete.

If no "PROTOCOL" is set on the PTZ screen, the following message is displayed on the screen.

"Please set up a camera type in setup menu."

Recording

1 2

This unit allows the following recording modes. Select the recording mode, recording resolution, frame rate

and video quality from "RECORD" under the MAIN MENU. (P35)

The symbol on the right side of each recording mode (Ex: R) is displayed while recording is in progress.

b Types of recording modes

A Real time recording (R) .................................. P16

Records manually videos being monitored.

B CONTINUOUS recording (C) ........................... P17

Records continuously when this unit is turned on.

C MOTION recording (M)..................................... P17

Records when set off by the motion sensor integrated in this unit.

D ALARM recording (A) ...................................... P18

Records when set off by a sensor connected to the external alarm terminal (ALARM IN) of this unit.

E SCHEDULE recording...................................... P19

Records according to the daily time slot set under the TIMER SET screen of the recording settings.

• The initial screen requests a password. (P38)

• It is possible to cancel the password request. See "Settings for no password" (P38)

Real time recording

Press the REC/STOP button while monitoring live

videos.

"R" is displayed on the recording display and recording starts.

CH1

Memo: • Setting the OVERWRITE (P46)

ON: Overwrites earlier data once the hard disk

capacity is full.

OFF: Stops recording operations once the hard

disk capacity is full.

Press the REC/STOP button once operations are

complete.

"R" disappears from the recording display and real time recording is stopped.

2007/05/03 09:04:54

• When recording rate is high, the audio may be difficult to hear at the time of playback and playback time may increase.

• Recording time varies depending on the screen being recorded. Furthermore, recording rate may decrease depending on the settings.

+ 53 hidden pages