Samsung WEA512I Users Manual

WEA512i (Indoor) Quick Installation Manual

This manual describes the configuration of the Wireless Enterprise WEA512i and its installation procedures.

Introduction

What is the WEA512i?

The Samsung WEA512i is an Access Point (AP) which has been designed for the wireless communications optimized for indoor hotspot environment. It offers unparalleled performance and connectives for all wireless devices such as smartphones, laptops, tablets etc. The WEA512i supports the following features:

- IEEE 802.11a/b/g/n/ac standard

- PoE (Power over Ethernet) IEEE 802.3af

- 2 × 2 MU-MIMO (Multi User-Multiple Input Multiple Output)

- Wireless LAN through both 2.4 GHz and 5 GHz bandwidth simultaneously

Components

After unpacking the WEA512i, check whether all of the following components are included.

WE A512i

Package Contents

Status LED

LED Status Description

System start status

Normal operation status

Upgrade Green blinking Software upgrade in progress

Error status Red blinking Physical connection error of network

White On Initial LED status

Blue On Device reset and test in progress

Red On Booting failure (Device reset failure)

Green On When there is no connected wireless UE

Blue On When there is a connected wireless UE

Yellow blinking IP address conflict

Purple blinking Dynamic IP address allocation failure

Bluish-green blinking Logical connection error of network

Red, green and off repeated

Wireless interface error

Installation

The WEA512i can be installed on ceilings or walls. Please check whether all the components are included before installation.

Mounting Bracket

Security Torx (T10) Screw Plastic 4 anchors 4 M4 × L28 screws

- It is recommended to keep all packaging materials and the box.

- The power adapter is sold separately. When necessary, please contact the place of purchase.

5 M3 × L6 screws

(Including 1 spare)

Installation Manual

Functions

Front View

Rear View

Status LED

Before Installation

Safety Requirements

Risks may be caused when the following safety warnings are not properly observed. For safe use, make sure to be well-informed.

- There is an electrical risk with the product. Make sure that the power is off during installation and do not proceed with the installation when there is current leakage. Use of products with current leakage may cause serious electrical shock to the user.

- Wear anti-static gloves or take appropriate actions to prevent ESD when handling the product.

- The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af/at shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in IEC/EN/UL60950-1.

- This product must be installed or removed only by appropriately-trained

service personnel.

- All interconnecting equipment including this product must be installed

within the same building. For details, refer to Environment A of IEEE

802.3af/at standard.

- This product must be installed with at least 3 m or more distance from the

WiMAX/3G/4G repeater or antenna.

Installation Instructions

DC Input

Ethernet Port (PoE)

A dust cover is installed on DC Input port (DC 48 V). Remove the cover before use.

Interface

Port Name

Status LED Displays the status information of the WEA512i via LED.

DC Input This is for connecting the power adapter when the PoE is not

available.

Ethernet Port (PoE)

Console Port This is used for checking the operational status of the WEA512i

Factory Reset Switch

Supports 1000 BASE-T Gigabit Ethernet and PoE IEEE 802.3af.

and for CLI input.

This is used to reset the WEA512i to the initial factory settings.

Description

Factory Reset Switch

Console Port

The instructions below must be followed when installing.

- It must be installed in a place that can be easily accessed for product installation, cable connection and maintenance.

- The PoE LAN cable must be always installed away from any electrical interference source such as power lines, fluorescent lights or transmitters.

- The PoE LAN cable must be CAT 5E or higher.

- When PoE is unavailable, a power adapter (sold separately) can be used. The 3-pin (including ground) power socket that supplies 100~240 V AC, 50~60 Hz must be located within 2 m from each equipment and the power must be supplied through an independent circuit breaker. It is recommended to use the equipment that uses a filter or a surge protector.

Installation on Ceilings (When the ceiling type is T-bar)

- When incorrectly installed on the ceiling, the WEA512i may drop onto a person or equipment. Therefore, make sure to fix it firmly.

- If the ceiling type is not T-Bar, please refer to the ‘Installation Manual’ provided separately. For this installation manual, please contact the dealer.

Remove the holding tape that was attached to fix the ceiling clip.

Holding tape

Open the ceiling clip so that it is wider than the width of the T-bar.

Move the ceiling clip so that it is appropriate for the T-bar width.

Fix the ceiling clip in place by tightening

the 4 designated screws.

Screws for fixing

the ceiling clip

Fix the T-bar in place by fastening the

screws (total of 2) that are on the ceiling clip.

Place the mounting bracket on the wall.

Mark and drill 4 screws in appropriate spots.

Use a hammer to insert

4 plastic anchors into the drilled holes on the wall. Align the inserted plastic anchors and the screw holes of the bracket. Fix the bracket to the wall by fastening four M4 × L28 screws.

Insert a LAN cable into the Ethernet port

(PoE) on the back side of the WEA512i.

If PoE is not supported, connect the power adapter to the DC input on the back of the WEA512i.

If the T-bar size of the ceiling is 15 mm, 24 mm or 38 mm, the position to fix the ceiling clip can be checked from the bottom surface of the mounting bracket. If the T-bar size is unknown, push the ceiling clip to check the fixing positions.

Pull out a LAN cable through a hole on the

ceiling and connect it to an Ethernet port (PoE) on the back side of the WEA512i.

Exterior of the ceiling

Screws for

fixing T-bar

The wall

Installing Anti-Theft Lock Cable

When installing the WEA512i in a public place, it is recommended to use anti- theft lock cables to prevent any loss. (An anti-theft lock cable can be purchased separately and a variety of products can be found in the market.)

Connect the anti-theft lock cable to the WEA512i.

Turn the lock cable key to lock the cable.

Remove the key from the lock cable and keep it in a separate location.

Using the anti-theft Torx screws

The WEA512i can be prevented from being stolen when tightening the Torx screws as shown below. (Torx screws can be easily tightening when they are fixed to the mounting bracket before assembling the AP product.)

If PoE is not supported, connect the power adapter to the DC input on the back side of the WEA512i.

Align the WEA512i with the

3 holes on the mounting bracket and then turn clockwise to fix it in place. Clean up the ceiling and other cables.

Installation on Walls

Remove the holding tape that was

attached to fix the ceiling clip.

Holding tape

Interior of the ceiling

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The 5150-5250 MHz band is restricted to indoor use only.

RF Radiation Exposure Statement:

This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Remove the ceiling clip from the mounting bracket.

Should the AP be installed in a ceiling with ventilation, the AP Ethernet port must be horizontally placed.

This product is RoHS compliant.

Frequency Range Output Power (Max.)

2400~2483.5 MHz ( WLAN 2.4G) 5150~5725 MHz (WLAN 5G) 5725~5875 MHz (non-Speciﬁc SRD)

19.49 dBm

28.70 d Bm

13.4 6 d Bm

AT BE CY DK EE FI

DE EL IE LU MT NL

SI ES SE UK NO CH

http://www.samsungenterprise.com

Part No.: EC68-00205A (Ver.1.0)