Page 1
User Manual
0
Page 2
User Manual
Introduction
Thank you for choosing Samsung DVR products.
This is the user manual for SVR-3200, SVR-1680C, SVR-1660C, SVR-1645, SVR-960C, SVR-
945, SVR-480. Before installing or operating this product, please familiarize yourself with this
user manual and other manuals referenced by this manual.
This user manual and the software and hardware described here are protected by the copyright
law. Therefore, with the exception of copying for general use within the copyright law, copying
and reprinting the user manual, either partially or in its entirety, or translating it into another
language without the consent of Samsung Techwin, Inc. is prohibited.
This specification may be changed without prior notice for improvement of product performance.
Product warranty and limits of responsibility
The manufacturer does not assume any other responsibility concerning the sale of this product
and does not delegate any right to a third party to take any responsibility on its behalf. Product
warranty does not cover cases of accidents, negligence, alteration, misuse or abuse. In addition,
no warranty is offered for any attachments or parts not supplied by the manufacturer.
The warranty period for this product will be for 3 years from the date of purchase. The following
cases are not covered by the warranty and payment is required for repairs.
Malfunction due to negligence in handling by the user
Deliberate disassembly and replacement by the user
Connection of an improper power supply
Malfunction caused by natural disasters (fire, flood, etc.)
Replacement of expendable parts (HDD, FAN, etc.)
※ Warranty period of HDD and Fan is one year after purchase.
Warranty only refers to the warranty covering products that have been paid for.
After expiration of the warranty period (3 years), examination and repair will be provided for a
fee. Even during the warranty period, repair and examination of items outside the preceding
warranty scope will require a payment.
This product is not for exclusive use of crime prevention but for assistance unit such as
a fire or theft. Therefore, we never take any responsibility for the damage from any
1
Page 3
User Manual
incident.
Various experience and technical is needed for installation of this product and an amateur
installation might cause fire, electric shock, and defect. All installation operations should be
performed by the agency you purchased this product from.
This manual is authored SVR-3200, SVR-1680C, SVR-1660C, SVR-1645, SVR-960C, SVR-945,
SVR-480 according to firmware version 1.4.0,
Content of this manual can differ by Firmware or Software upgrade, and standard and
appearance of product is changeable partly without prior notice to users.
2
Page 4
User Manual
Contents
Chapter 1. Safety Cautions ............................................................ 7
1.1 Explaining the Symbols ................................................................................................... 7
Chapter 2. Summary ..................................................................... 10
2.1 Features ........................................................................................................................ 10
Chapter 3. Product Description ................................................... 14
3.1 Front Part ...................................................................................................................... 14
3.1.1 SVR-3200 ........................................................................................................... 14
3.1.2 SVR-1680C, SVR-1660C, SVR-1645 ................................................................ 16
3.1.3 SVR-960C .......................................................................................................... 18
3.1.4 SVR-945 ............................................................................................................. 20
3.1.5 SVR-480 ............................................................................................................. 22
3.2 Rear Part ....................................................................................................................... 24
3.2.1 SVR-3200 ........................................................................................................... 24
3.2.2 SVR-1680C, SVR-1660C, SVR-1645 ................................................................ 25
3.2.3 SVR-960C .......................................................................................................... 26
3.2.4 SVR-945 ............................................................................................................. 27
3.2.5 SVR-480 ............................................................................................................. 28
3.3 OSD MENU structure .................................................................................................... 29
3.4 Function Menu .............................................................................................................. 30
3.5 Factory setting .............................................................................................................. 30
Chapter 4. Monitoring ................................................................... 37
4.1 Default Display .............................................................................................................. 37
4.2 Single Display Full Screen ............................................................................................ 37
4.3 Multi Display .................................................................................................................. 37
4.4 Auto Sequencing ........................................................................................................... 37
4.4.1 Default System Mode ......................................................................................... 38
4.4.2 Auto Sequencing Mode ...................................................................................... 38
4.4 Event Screen ................................................................................................................ 39
4.5 Zoom In ......................................................................................................................... 40
3
Page 5
User Manual
4.6 Live Video Pause .......................................................................................................... 40
4.7 PTZ Control ................................................................................................................... 41
4.7.1 Pan/Tilt ............................................................................................................... 42
4.7.2 Zoom/Focus ....................................................................................................... 42
4.7.3 Load Preset ........................................................................................................ 42
4.7.4 Save Preset ........................................................................................................ 42
4.7.5 Auxiliary On ........................................................................................................ 42
4.7.6 Auxiliary Off ........................................................................................................ 43
4.7.7 Menu .................................................................................................................. 43
5.1 Playback Mode ............................................................................................................. 44
5.1.1 Playback on Default Display (16/9/4 channel split-screen) ............................... 44
5.1.2 Playback ............................................................................................................. 44
5.2 Search Mode ................................................................................................................. 45
5.2.1 Time Search ....................................................................................................... 45
5.2.2 Calendar Search ................................................................................................ 46
5.2.3 Event Search ...................................................................................................... 46
5.2.4 Thumbnail Search .............................................................................................. 47
5.3 Copy .............................................................................................................................. 48
5.3.1 CD/DVD ............................................................................................................. 48
5.3.2 RE4 .................................................................................................................... 50
5.3.3 AVI ...................................................................................................................... 51
Chapter 6. Setup ........................................................................... 53
6.1 Record Setup ................................................................................................................ 53
6.2 Time Setup .................................................................................................................... 53
6.2.1 How to Set Time ................................................................................................. 54
6.3 Camera Setup ............................................................................................................... 55
6.3.1 How to Set a Camera ......................................................................................... 56
6.4 Monitor Setup ................................................................................................................ 57
6.5 Record Setup ................................................................................................................ 58
6.5.1 Program Setup ................................................................................................... 59
6.5.2 Manual/Schedule Recording Setup ................................................................... 62
6.5.3 Evnet Record Setup ........................................................................................... 65
6.6 Audio Setup .................................................................................................................. 68
4
Page 6
User Manual
6.6.1 Audio .................................................................................................................. 68
6.6.2 Audio Mixing ....................................................................................................... 69
6.7 General Event Setup ..................................................................................................... 69
6.7.1 Text Setup .......................................................................................................... 71
6.7.2 Preset ................................................................................................................. 72
6.7.3 Digital I/O ........................................................................................................... 73
6.7.4 Event Action ....................................................................................................... 74
6.8 Network ......................................................................................................................... 76
6.8.1 xDSL .................................................................................................................. 78
6.8.2 DDNS ................................................................................................................. 78
6.8.3 NTP .................................................................................................................... 83
6.8.4 Remote ............................................................................................................... 84
6.9 System Setup ................................................................................................................ 90
6.9.1 System Setup ..................................................................................................... 91
6.9.2 Disk .................................................................................................................... 93
6.9.3 Security .............................................................................................................. 95
6.10 Exit ................................................................................................................................ 97
Chapter 7. Web Viewer ................................................................. 99
7.1 System Requirements ....................................................................................................... 99
7.2 LOGIN ................................................................................................................................ 99
7.3 Connection User setup .................................................................................................... 100
7.4 Supported Browser .......................................................................................................... 101
7.5 Monitor ............................................................................................................................. 101
7.5.1 Screen Partition & Image Movement ............................................................... 101
7.5.2 Moving Playback .............................................................................................. 102
7.5.3 Channel On/Off ................................................................................................ 102
7.5.4 Sensor indication.............................................................................................. 103
7.5.5 Relay operation ................................................................................................ 103
7.5.6 Microphone use ................................................................................................ 103
7.5.7 Event Data ....................................................................................................... 104
7.5.8 Video Recording & Video Storage ................................................................... 104
7.5.9 PTZ Use ........................................................................................................... 105
7.5.10 Audio Use ......................................................................................................... 106
7.5.11 Image Channel Close ...................................................................................... 106
5
Page 7
User Manual
7.6 Playback .......................................................................................................................... 106
7.6.1 Screen Division & Channel Change ................................................................. 106
7.6.2 Image Recording .............................................................................................. 107
7.6.3 Print .................................................................................................................. 107
7.6.4 Move to Web Monitor ....................................................................................... 107
7.6.5 Channel On/Off ................................................................................................ 107
7.6.6 Recording Duration & Recording Size Check .................................................. 108
7.6.7 Calendar Search .............................................................................................. 108
7.6.8 Playback Toolbar .............................................................................................. 108
Trouble Shooting ........................................................................ 109
Compatible HDD List ................................................................... 111
Compatible Media List ................................................................. 111
Specification ................................................................................ 111
Dimensions ................................................................................. 116
6
Page 8
User Manual
Chapter 1. Safety Cautions
1.1 Explaining the Symbols
Warning
Refers to information users need to know in order to prevent serious injury or
death.
Before installation
Verify the supplied voltage (AC100V~AC240V) before connecting to the power supply.
Make sure the power supply is off before installation.
Do not install in a very humid environment. Doing so may cause an electric shock or fire.
Make sure ground line is connected to reduce electric shock risk.
During operation
Do not open the product cover except by qualified personnel or system installer. Opening the
product cover may cause an electric shock.
Do not plug multiple appliances into a single power outlet. Doing so may cause fire.
Do not place dishes holding water or heavy objects on the product. Doing so may cause a
malfunction.
Do not use in areas where inflammable substances such as propane gas or gasoline or high
amount of dust is present. Doing so may cause an explosion or fire.
Do not touch the power line with a wet hand. Doing so may cause an electric shock.
Do not insert a hand into the opening of the DVD. Doing so may cause an injury.
Make sure conductive materials do not enter the cooling ventilator opening.
Do not apply excessive force when pulling on the power cord. Damaging the cord may cause
an electric shock or fire.
Improper replacement of the built-in battery by other types of batteries may cause explosion.
The batter must be replaced by the same battery type. Also, expired batteries may cause
pollution and must be disposed of with care.
Do not place the battery in fire or in extreme heat. Also, do not dissect or disassemble the
battery.
Recharge the batteries for the remote controller.
Dismantling and cleaning
Do not dismantle, repair or modify the product deliberately. Doing so may cause a damage, an
electric shock or an injury.
7
Page 9
User Manual
Do not use water, paint thinner or organic solvent for cleaning the product exterior. Doing so
may cause a malfunction or an electric shock. Use a dry cloth to clean the exterior.
Caution
Provides information users need to know in order to prevent minor
injury or product damage.
During installation
For adequate ventilation, install the product with at least 15cm of space between the cooler
and the wall surface.
To prevent falling, install the product on a flat area . Dropping the product may cause an injury
or a malfunction.
Avoid areas exposed to direct exposure to sun light or excessive heat since they may cause
deformation or a malfunction.
If a camera is installed while the DVR is being recorded, image in another channel may be
disrupted. Starting the storage after the camera has been installed is recommended.
During use
Make sure the product is not exposed to concussions or shaking during usage or movement.
Do not move, throw or expose to excessive physical concussion during usage.
Installing additional unapproved hard disk drives may result in abnormal operation. Inquire at
the agency of purchase before installing additional hard disk drives.
Product warranty will not cover malfunctions due to additional installation of unapproved hard
disk drives.
This product is a supplementary rather than primary means for preventing fire and theft. Our
company is not responsible for accidents or damage that may occur.
Samsung Techwin recommends the installation of a UPS (Uninterrupted Power
Supply) with all its recording products.
Samsung Techwin cares for the environment at all product
manufacturing stages, and is taking a number of steps to provide
customers with more environmentally friendly products. The Eco
mark represents Samsung Techwin’s will to create environmentally
friendly products, and indicates that the product satisfies the EU
RoHS Directive.
FCC Compliance Statement
NOTE : This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
8
Page 10
User Manual
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which cause the user will be required to correct the interference at his own expense.
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate
collection systems.) This marking shown on the product or its literature, indicates that it
should not be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate this from other types of wastes and recycle it responsibly to promote the
sustainable reuse of material resources. Household users should contact either the retailer where
they purchased this product, or their local government office, for details of where and how they can
take this item for environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Correct Disposal of Batteries in this Product
(Applicable in the European Union and other European countries with
separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this
product should not be disposed of with other household waste at the end of their
working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the
battery contains mercury, cadmium or lead above the reference levels in EC
Directive 2006/66. If batteries are not properly disposed of, these substances can cause harm to
human health or the environment. To protect natural resources and to promote material reuse,
please separate batteries from other types of waste and recycle them through your local, free battery
return system. The rechargeable battery incorporated in this product is not user replaceable.
For information on its replacement, please contact your service provider.
9
Page 11
User Manual
Chapter 2. Summary
This unit is a digital video recording and playback device to record image and video input
from 32/16/9 channels to its built-in hard disk. The buttons on the front of the unit as well
as the mouse and GUI allow easy setup and operation.
The Samsung SVR series of digital video recorders (DVRs) provide additional safety and
security to banks, apartment buildings and complexes, government offices as well as
other public, private and commercial facilities. Recorded high-quality video and images
are stored on hard disk for later retrieval or playback. Real time functionality delivers
users with the ability to simultaneously record multiple channels, playback video, and
copy video. A few of the more advanced user-conveniences include motion detection,
Pan/Tilt/Zoom controls (PTZ), password protection, real time audio recording, event lists,
and log files.
2.1 Features
Monitoring Screen
The monitoring screen supports vivid, high-definition live visual feed from each channel and
provides multiple screens.
Real time MPEG-4 visual output (480 frames)
Multiple split-screen monitoring modes
SVR-3200/1680C/1660C/1645: Single, 4, 9, 10, 16
SVR-960C/945: Single, 4, 9
SVR-480 : Single, 4
Automatic Screen Switching (AUTO)
Supports various monitor output modes
SVR-3200: 4 Composite, 2 VGA
SVR-1680C: 4 Composite, 1 VGA
SVR-1660C/1645/960C/945/480: 2 Composite, 1 VGA
Pan/Tilt, Digital Zoom, PIP (Picture-In-Picture), The PIP function will be
available with a firmware upgrade in the future.
Audio Recording
SVR series DVRs provide real time audio recording.
Simultaneous recording of 16/9/4 channels of audio in real time
SVR-3200/1680C/1600/1645 : Input - 16 channels (4 RCA in rear, 12 D-SUB),
10
Page 12
User Manual
Output - 1 in rear, SVR-960C/945 : 9 channels (4 RCA in rear, 5 D-SUB),
Output - 1 in rear, SVR-480 : 4 channels (4RCA), Output – 1 in rear
Supports simultaneous recording and playback
Video Recording
The product is capable of storing visual image data as high resolution MPEG-4 video at up
to 480 frames per second, as well as pre-emptively initiating recording sequences up to five
seconds prior to an event. The COVERT feature (concealment of private visual data) helps
to protect privacy.
High quality real time MPEG-4 recording
Three screen-resolution levels for improved control over data sizes
Multi-recording for manual and scheduled events
Simultaneous recording/playback/backup/networking
Easily accessible options for channel-specific resolution and motion detection
ranges
Per-second frame rates (up to 30 frames per channel) are user customizable
SVR-3200 Half D1 : NTSC (704x240) 960fps, PAL (704x288) 800fps
SVR-1680C D1 : NTSC (704x480) 480fps, PAL (704x576) 400fps
SVR-1660C/1645 CIF : NTSC (352x240) 480fps, PAL (352x288) 400fps
SVR-960C/945 CIF : NTSC (352x240) 270fps, PAL (352x288) 225fps
SVR-480 D1 : NTSC (704x480) 120fps, PAL (704x576) 100fps
Manual and scheduled recording
Video signal loss detection
Event logs (sensors, D-I/O, video loss, motion detection, text)
Each channel supports pre-emptive recording sequences up to 5 seconds prior
to an actual event
Search/Playback
Various search and playback options are offered for the user’s convenience.
Playback by time, date and channel
Mouse interface increases data searchability
Forward/backward search while playback is paused
Playback by event log entry (sensor, video loss, motion detection and text)
Remote controller and Jog/Shuttle further improve searching (The SVR-
960C/945/480 models do not support Jog/Shuttle.)
Full-frame playback (Available in SVR-3200/1680C/1660C only)
Data Storage
The hard disk included with the product is for data storage. If desired, recorded data can be
11
Page 13
User Manual
backed up or stored to DVD-R, CD-R or a USB storage device.
The built-in hard disk is provided as primary storage
Multiple portable data storage media are supported: DVD-R, CD-R and USB
※ Refer to the appendix on the back of the manual regarding compatible
media types.
Hard disk expansion device (external recording device): SVS-5E (optional)
External hard disk expansion is supported with the SVS-5E (Available for
purchase separately)
12
Page 14
User Manual
Networking
The product supports LAN, xDSL and other networking capabilities. Combined with the PC
interface client, the core features of the device can be easily remotely controlled.
E-mails can be sent via TCP/IP or DHCP upon an event trigger
Remote live visual feed (single or 4 section split-screen)
PC playback, storage, search and DVR control functions via Network Viewer
Remote recording, search and playback scheduling
Supports 10/100Mbps Ethernet/xDSL
Multiple DVR connections
Miscellaneous
User-friendly GUI and mouse interface
Simplified firmware upgrades through USB
Visual data recording and backup to USB
Supports PTZ control (SPEED DOME), Coax, PRESET
Multilingual support: Korean, English, Italian, Spanish, Japanese
Single remote controller to control 16 DVRs
13
Page 15
User Manual
Chapter 3. Product Description
3.1 Front Part
3.1.1 SVR-3200
No. Classification Function
DVD-Multi for
1
copying
2 Channel LED Shows the data input and event operation status
3 JOG/SHUTTLE
4 Channel button Selects channel in live feed or playback
5 AUTO Starts or stops user defined sequences.
6 MULTI Changes split-screen sections for live video feeds or
7 MENU Navigates into the Menu.
8 SEARCH Starts Search mode.
9 REC button Starts or stops manual recording
For copying recorded video and images to DVD/CD
optical media.
Jog can adjust setting values, control the STEP function,
navigate through the menu, and adjust the playback
speed and direction. Shuttle controls PTZ.
playback.
REC lamp Lit when recording.
HDD lamp Lit when HDD is working.
10
NETWORK lamp Lit when network is connected.
EVENT lamp Lit when an event is detected.
14
Page 16
User Manual
COPY lamp Indicates copying operation.
PLAY lamp Lit when copying.
11 Power button Turns on or off the device.
12 ESC button The Escape button navigates up the menu tree and
closes dialog windows.
13 COPY Starts Copy mode.
14 FUNC Starts Function mode.
15 MONITOR Cycles through from Monitor 1 to 4.
16 PTZ Starts or ends PTZ function.
17
USB ports for external devices (mouse, USB memory
USB1, USB2
stick).
18 PLAY/ENTER Start playback or select an item on the menu.
19
◀/REW
Navigates or selects in the menu, or for playback,
changes the reverse playback speed.
20
▶/FWD
Navigates or selects in the menu, or for playback,
changes the forward playback speed.
31 ▲/PAUSE Navigates or selects in the menu, or for playback,
pauses live or recorded video.
▼/STOP Navigates or selects in the menu, or for playback, stops
22
playback.
15
Page 17
User Manual
3.1.2 SVR-1680C, SVR-1660C, SVR-1645
No. Classification Function
DVD-Multi for
For copying recorded video and images to DVD/CD
1
copying
optical media.
2 Channel LED Shows the data input and event operation status
Jog can adjust setting values, control the STEP function,
3 JOG/SHUTTLE
navigate through the menu, and adjust the playback
speed and direction. Shuttle controls PTZ.
4 Channel button Selects channel in live feed or playback
5 AUTO Starts or stops user defined sequences.
6 MULTI Changes split-screen sections for live video feeds or
playback.
7 MENU Navigates into the Menu.
8 SEARCH Starts Search mode.
9 REC button Starts or stops manual recording
REC lamp Lit when recording.
HDD lamp Lit when HDD is working.
10
NETWORK lamp Lit when network is connected.
EVENT lamp Lit when an event is detected.
COPY lamp Indicates copying operation.
PLAY lamp Lit when copying.
11 Power button Turns on or off the device.
12 ESC button The Escape button navigates up the menu tree and
16
Page 18
User Manual
closes dialog windows.
13 COPY Starts Copy mode.
14 FUNC Starts Function mode.
15 MONITOR Cycles through from Monitor 1 to 4 : SVR-1680C,
Switches from main and sub monitor : SVR-1660C,
SVR-1645
16 PTZ Starts or ends PTZ function.
17
USB ports for external devices (mouse, USB memory
USB1, USB2
stick).
18 PLAY/ENTER Start playback or select an item on the menu.
19
◀/REW
Navigates or selects in the menu, or for playback,
changes the reverse playback speed.
20
▶/FWD
Navigates or selects in the menu, or for playback,
changes the forward playback speed.
31 ▲/PAUSE Navigates or selects in the menu, or for playback,
pauses live or recorded video.
▼/STOP Navigates or selects in the menu, or for playback, stops
22
playback.
17
Page 19
User Manual
r
3.1.3 SVR-960C
No. Classification Function
DVD-Multi fo
For copying recorded video and images to DVD/CD
1
copying
optical media.
2 Channel LED Shows the data input and event operation status
3 Channel button Selects channel in live feed or playback
4 AUTO Starts or stops user defined sequences.
5 MULTI Changes split-screen sections for live video feeds or
playback.
6 MENU Navigates into the Menu.
7 SEARCH Starts Search mode.
8 REC button Starts or stops manual recording
REC lamp Lit when recording.
HDD lamp Lit when HDD is working.
NETWORK lamp Lit when network is connected.
9
EVENT lamp Lit when an event is detected.
COPY lamp Indicates copying operation.
PLAY lamp Lit when copying.
10 Power button Turns on or off the device.
11 ESC button The Escape button navigates up the menu tree and
closes dialog windows.
12 COPY Starts Copy mode.
13 FUNC Starts Function mode.
18
Page 20
User Manual
14 MONITOR Switches from main and sub monitor
15 PTZ Starts or ends PTZ function.
16
USB ports for external devices (mouse, USB memory
USB1, USB2
stick).
17 PLAY/ENTER Start playback or select an item on the menu.
18
◀/REW
Navigates or selects in the menu, or for playback,
changes the reverse playback speed.
19
▶/FWD
Navigates or selects in the menu, or for playback,
changes the forward playback speed.
20 ▲/PAUSE Navigates or selects in the menu, or for playback,
pauses live or recorded video.
▼/STOP Navigates or selects in the menu, or for playback, stops
21
playback.
19
Page 21
User Manual
3.1.4 SVR-945
No. Classification Function
1 Channel LED Shows the data input and event operation status
2 Channel button Selects channel in live feed or playback
3 AUTO Starts or stops user defined sequences.
4 MULTI Changes split-screen sections for live video feeds or
playback.
5 MENU Navigates into the Menu.
6 SEARCH Starts Search mode.
7 REC button Starts or stops manual recording
REC lamp Lit when recording.
HDD lamp Lit when HDD is working.
NETWORK lamp Lit when network is connected.
8
EVENT lamp Lit when an event is detected.
COPY lamp Indicates copying operation.
PLAY lamp Lit when copying.
9 Power button Turns on or off the device.
10 ESC button The Escape button navigates up the menu tree and
closes dialog windows.
11 COPY Starts Copy mode.
12 FUNC Starts Function mode.
13 MONITOR Switches from main and sub monitor
20
Page 22
User Manual
14 PTZ Starts or ends PTZ function.
15
USB ports for external devices (mouse, USB memory
USB1, USB2
stick).
16 PLAY/ENTER Start playback or select an item on the menu.
17
◀/REW
Navigates or selects in the menu, or for playback,
changes the reverse playback speed.
18
▶/FWD
Navigates or selects in the menu, or for playback,
changes the forward playback speed.
19 ▲/PAUSE Navigates or selects in the menu, or for playback,
pauses live or recorded video.
▼/STOP Navigates or selects in the menu, or for playback, stops
20
playback.
21
Page 23
User Manual
r
3.1.5 SVR-480
No Classification Function
DVD-Multi fo
For copying recorded video and images to DVD/CD optical
1
copying
media.
2 Channel button Selects channel in live feed or playback
3 Channel LED Shows the data input and event operation status
4 AUTO Starts or stops user defined sequences.
5 MULTI Changes split-screen sections for live video feeds or
playback.
6 MENU Navigates into the Menu.
7 SEARCH Starts Search mode.
8 REC button Starts or stops manual recording
REC lamp Lit when recording.
HDD lamp Lit when HDD is working.
9
NETWORK
lamp
Lit when network is connected.
EVENT lamp Lit when an event is detected.
COPY lamp Indicates copying operation.
PLAY lamp Lit when copying.
10 Power button Turns on or off the device.
11 USB1, USB2 USB ports for external devices (mouse, USB memory stick).
12 ESC button The Escape button navigates up the menu tree and closes
22
Page 24
User Manual
dialog windows.
13 COPY Starts Copy mode.
14 FUNC Starts Function mode.
15 MONITOR Switches from main and sub monitor
16 PTZ Starts or ends PTZ function.
17 PLAY/ENTER Start playback or select an item on the menu.
18
◀/REW
Navigates or selects in the menu, or for playback, changes
the reverse playback speed.
19
▶/FWD
Navigates or selects in the menu, or for playback, changes
the forward playback speed.
20 ▲/PAUSE Navigates or selects in the menu, or for playback, pauses
live or recorded video.
▼/STOP Navigates or selects in the menu, or for playback, stops
21
playback.
23
Page 25
User Manual
3.2 Rear Part
3.2.1 SVR-3200
No. Input/Output
terminal name
1 POWER IN Socket for AC 100V ~ AC 240V power cord.
2 CH1 ~ 32 Connection terminal for camera BNC input.
3 MONITOR 1 ~ 4 Connection terminal for monitor BNC output.
4 AUDIO IN(RCA) RCA audio jack for RCA input.
5 AUDIO OUT Audio jack for speaker output.
6 GROUND Ground terminal between DVR and external device.
7 ETHERNET Ethernet port for network connections (RJ-45).
8 STORAGE External storage connection port (Function not supported in the
current version)
9 eSATA Connection terminal for external eSATA HDD or HDD for backups.
10 VGA OUTPUT Output port for PC monitor.
11 Serial Port (Terminal
Connection terminal for expanded controller, speed dome camera,
Function
Block)
RS-232C/485/422
12 Serial Port (D-Sub) RS-232C D-SUB connector.
13 RELAY OUT Connection terminal for relay output.
14 SENSOR IN Connection terminal for sensor input.
etc.
24
Page 26
User Manual
15 AUDIO IN(D-SUB) Connection terminal for audio output D-SUB.
16 D-I/O Connection terminal for DIGITAL IN/OUT.
3.2.2 SVR-1680C, SVR-1660C, SVR-1645
No. Input/Output
Function
terminal name
1 POWER IN Socket for AC 100V ~ AC 240V power cord.
2 CH1~16 Connection terminal for camera BNC input.
3 LOOP OUT Connection terminal for camera BNC output (loop).
4 MONITOR 1 ~ 2 Connection terminal for monitor BNC output.
5 AUDIO IN(RCA) RCA audio jack for RCA input.
6 AUDIO OUT Audio jack for speaker output.
7 GROUND Ground terminal between DVR and external device.
8 ETHERNET Ethernet port for network connections (RJ-45).
9 STORAGE External storage connection port (Function not supported in
the current version)
10 eSATA Connection terminal for external eSATA HDD or HDD for
backups.
11 VGA OUTPUT Output port for PC monitor.
12 Serial Port (Terminal
Block) RS-232C/485/422
Connection terminal for expanded controller, speed dome
camera, etc.
13 Serial Port (D-Sub) RS-232C D-SUB connector.
14 RELAY OUT Connection terminal for relay output.
25
Page 27
User Manual
15 SENSOR IN Connection terminal for sensor input.
16 AUDIO IN(D-SUB) Connection terminal for audio output D-SUB.
17 D-I/O Connection terminal for DIGITAL IN/OUT.
3.2.3 SVR-960C
No. Input/Output
Function
terminal name
1 POWER IN Socket for AC 100V ~ AC 240V power cord.
2 GROUND Ground terminal between DVR and external device.
3 CH1~9 Connection terminal for camera BNC input.
4 LOOP OUT Connection terminal for camera BNC output (loop).
5 MONITOR 1 ~ 2 Connection terminal for monitor BNC output.
6 AUDIO IN(RCA) RCA audio jack for RCA input.
7 AUDIO OUT Audio jack for speaker output.
8 ETHERNET Ethernet port for network connections (RJ-45).
9 eSATA Connection terminal for external eSATA HDD or HDD for backups.
10 VGA OUTPUT Output port for PC monitor.
11 Serial Port (D-Sub) RS-232C D-SUB connector.
12 Serial Port (Terminal
Connection terminal for expanded controller, speed dome camera,
Block)
etc.
RS-232C/485/422
13 RELAY OUT Connection terminal for relay output.
14 SENSOR IN Connection terminal for sensor input.
26
Page 28
User Manual
15 AUDIO IN(D-SUB) Connection terminal for audio output D-SUB.
16 D-I/O Connection terminal for DIGITAL IN/OUT.
3.2.4 SVR-945
No. Input/Output
Function
terminal name
1 CH1~9 Connection terminal for camera BNC input.
2 LOOP OUT Connection terminal for camera BNC output (loop).
3 MONITOR 1 ~ 2 Connection terminal for monitor BNC output.
4 AUDIO IN(RCA) RCA audio jack for RCA input.
5 AUDIO OUT Audio jack for speaker output.
6 ETHERNET Ethernet port for network connections (RJ-45).
7 eSATA Connection terminal for external eSATA HDD or HDD for
backups.
8 VGA OUTPUT Output port for PC monitor.
9 Serial Port (D-Sub) RS-232C D-SUB connector.
10 Serial Port (Terminal
Block) RS-232C/485/422
Connection terminal for expanded controller, speed dome
camera, etc.
11 RELAY OUT Connection terminal for relay output.
12 AUDIO IN(D-SUB) Connection terminal for audio output D-SUB.
13 SENSOR IN Connection terminal for sensor input.
14 D-I/O Connection terminal for DIGITAL IN/OUT.
27
Page 29
User Manual
o
15 GROUND Ground terminal between DVR and external device.
16 POWER IN Socket for AC 100V ~ AC 240V power cord.
3.2.5 SVR-480
No. Input/Output
Function
terminal name
1 GROUND Ground terminal between DVR and external device.
2 CH1~4 Connection terminal for camera BNC input.
3 LOOP OUT Connection terminal for camera BNC output (loop).
4 MONITOR 1 ~ 2 Connection terminal for monitor BNC output.
5 AUDIO IN(RCA) RCA audio jack for RCA input.
6 AUDIO OUT Audio jack for speaker output.
7 ETHERNET Ethernet port for network connections (RJ-45).
8 eSATA Connection terminal for external eSATA HDD or HDD f
backups.
9 Serial Port (D-Sub) RS-232C D-SUB connector.
10 VGA OUTPUT Output port for PC monitor.
11 Serial Port (Terminal Block)
Connection terminal for expanded controller, speed
RS-485/422
dome camera, etc.
12 RELAY OUT Connection terminal for relay output.
13 SENSOR IN Connection terminal for sensor input.
14 POWER IN Socket for AC 100V ~ AC 240V power cord.
28
Page 30
User Manual
Refer to detailed description for inst allation & use from “Inst all Manual”.
3.3 OSD MENU structure
The menu structure is as shown below. For detailed instructions for configuration, please refer to
Chapter 4, 5 and 6.
29
Page 31
User Manual
3.4 Function Menu
The function menu allows the users to access any and all functions and operations of the product with the
mouse. To execute a particular function, left-click the icon. Also, all functions listed in the function menu
can be executed in full-screen mode. The function menu structure is as shown below.
3.5 Factory setting
To restore the unit back to its factory settings, go to System > System > Restore Factory Setting.
A pop-up window saying, "Warning : The system will be reset. Continue with restoring factory
default?" will appear. Select "Yes" and press Enter to restore the factory default settings.
Factory Default
Quick Setup
Record Mode ¡¡ Manual & Event
Schedule Not Set
Event Check Always
Language English
Time ¡¡ UTC 00:00 Dublin
No
30
Page 32
User Manual
Display Setup
MM/DD/YYYY
Current time
Channel
Display
Channel Number Ch1
Title Cam 1
Status Enable
Color Color
AGC Enable
Brightness 0
Contrast 0
Monitor Monitor Number Main Monitor (Monitor 1)
Covert Channel Deselect All
Sequencing Number 1 is set to Channel 1 and
Number 2 is set to Channel 2 in order.
Dwell Time 5 sec.
Multi Display 4E Channels 1, 3, 5 and 7
VGA Mode 800x600@56Hz
On Screen Display Select All
Record Setup
Record Record Mode Schedule & Event
Schedule Not Set All
Event Duration Before: 1 sec., After: 1 sec.
Repeat Record
On
Mode
Warning Level ¡¡ 45%
Record Data
Off
Retention
Playback
On
Deinterlace
Audio >>
Audio
Ch1
Channel
Audio
Off
Recording
Audio Gain 0
Sync Video Ch1
31
Page 33
User Manual
Channel
Audio Mix Mix On
Program A~Z ¡¡ CIF, 0fps, Q1
Event Setup
Event Event Check Always
Normal
Event
Event Screen /Dwell
Monitor 1 Off
time
Event Action Relay 1
Action
10 sec.
Duration
Normal Event
Deselect All
Source
System Event
Deselect All
Source
MD Ch1
MD Sensitivity 2
Area Set All
Sensor N.O
Text >>
Recording Off
Sync Text
Ch1
With
Device Manual
Seek Header Off
Header 1 header1
Header 2 header2
Delimiter 0D0A
Timeout(ms) 1000
Lines 20
Preset Channel Number Ch1
Preset Not Set
D-I/O D-I/O Output
Output Type Sensor
Network
Network Type Ethernet
DHCP Off
32
Page 34
User Manual
IP addr Default IP
Net Mask Default NM
Gateway Default GW
DNS1 0.0.0.0
Additional DNS 0.0.0.0
Port 4000
BandWidth
0
Limit(Mbps)
xDSL User ID ¡¡ guest
Password *****
Status xDSL not connected.
Port 4000
Bandwidth Limit
0.0
(Mbps)
DDNS Interval Off
Server
www.samsungipolis.com
ID None
Password None
Status Not Registered
NTP Sync With NTP Off
NTP Mode Client
NTP Server Loc. ¡¡ Public
NTP Local Server IP 0.0.0.0
Interval 1 (hour)
Remote Remote Keyboard ID Com1
Remote Controller
All
ID
Remote
Enable
Configuration Setup
Remote Relay Enable
Serial Com1, >>
PTZ
Ch1, >>
System Setup
System Language English
Key Buzzer On
33
Page 35
User Manual
Default >>
Load/Save
Load, >>
Configuration
Firmware Update >>
DVR Alias DVR0
System Log >>
I-Frame Interval Auto
Time >>
Disk Disk Manager >>
Disk Status >>
Security Change P/W Default value
Menu Check X, Admin and User: O
PTZ Check X, Admin and User: O
Relay Off Check X, Admin and User: O
Playback Check X, Admin and User: O
Power Off Check X, Admin and User: O
Power On Check X, Admin and User: O
Copy Check X, Admin and User: O
N/MIC Check None, Admin and User: O
Exit
Exit Save >>
Do not save >>
34
Page 36
User Manual
Record Program
Model SVR-1660C/1645 SVR-960C/945
Mode Normal Event Normal Event
Res Fps Q Res Fps Q Res Fps Q Res Fps Q
A D1 7 Q5 D1 7 Q5 D1 7 Q5 D1 7 Q5
B D1 5 Q5 D1 7 Q5 D1 5 Q5 D1 7 Q5
C D1 5 Q4 D1 7 Q5 D1 5 Q4 D1 7 Q5
D D1 3 Q5 D1 5 Q5 D1 3 Q5 D1 5 Q5
E D1 5 Q4 D1 7 Q5 D1 5 Q4 D1 7 Q5
F D1 3 Q4 D1 5 Q4 D1 3 Q4 D1 5 Q4
G D1 1 Q4 D1 3 Q4 D1 1 Q4 D1 3 Q4
H D1 0 Q4 D1 7 Q5 D1 0 Q4 D1 7 Q5
I Half 10 Q5 Half 15 Q5 Half 10 Q5 Half 15 Q5
J Half 5 Q5 Half 20 Q5 Half 5 Q5 Half 20 Q5
Program
K Half 3 Q5 Half 10 Q5 Half 3 Q5 Half 10 Q5
L Half 10 Q4 Half 20 Q5 Half 10 Q4 Half 20 Q5
M Half 10 Q4 Half 15 Q5 Half 10 Q4 Half 15 Q5
N Half 5 Q4 Half 10 Q5 Half 5 Q4 Half 10 Q5
O Half 5 Q4 Half 10 Q4 Half 5 Q4 Half 10 Q4
P Half 3 Q4 Half 5 Q4 Half 3 Q4 Half 5 Q4
Q Half 1 Q4 Half 3 Q4 Half 1 Q4 Half 3 Q4
R Half 0 Q4 Half 7 Q5 Half 0 Q4 Half 7 Q5
S CIF 30 Q5 CIF 30 Q5 CIF 30 Q5 CIF 30 Q5
T CIF 20 Q5 CIF 30 Q5 CIF 20 Q5 CIF 30 Q5
U CIF 20 Q4 CIF 20 Q5 CIF 20 Q4 CIF 20 Q5
V CIF 10 Q4 CIF 15 Q4 CIF 10 Q4 CIF 15 Q4
W CIF 7 Q3 CIF 25 Q5 CIF 7 Q3 CIF 25 Q5
X CIF 4 Q3 CIF 10 Q4 CIF 4 Q3 CIF 10 Q4
Y CIF 1 Q4 CIF 3 Q4 CIF 1 Q4 CIF 3 Q4
Z CIF 0 Q4 CIF 7 Q5 CIF 0 Q4 CIF 7 Q5
Model SVR-1680C SVR-3200
Mode Normal Event Normal Event
Res Fps Q Res Fps Q Res Fps Q Res Fps Q
A D1 30 Q5 D1 30 Q5 D1 15 Q5 D1 15 Q5
35
Page 37
User Manual
Program B D1 20 Q5 D1 30 Q5 D1 10 Q5 D1 15 Q5
C D1 20 Q4 D1 30 Q5 D1 10 Q4 D1 15 Q5
D D1 15 Q5 D1 15 Q5 D1 7 Q5 D1 7 Q5
E D1 20 Q4 D1 30 Q5 D1 10 Q4 D1 15 Q5
F D1 15 Q4 D1 15 Q4 D1 7 Q4 D1 7 Q4
G D1 4 Q4 D1 4 Q4 D1 4 Q4 D1 4 Q4
H D1 0 Q4 D1 30 Q5 D1 0 Q4 D1 15 Q5
I Half 30 Q5 Half 30 Q5 Half 30 Q5 Half 30 Q5
J Half 15 Q5 Half 20 Q5 Half 15 Q5 Half 20 Q5
K Half 4 Q5 Half 10 Q5 Half 4 Q5 Half 10 Q5
L Half 20 Q4 Half 20 Q5 Half 20 Q4 Half 20 Q5
M Half 20 Q4 Half 15 Q5 Half 20 Q4 Half 15 Q5
N Half 15 Q4 Half 20 Q5 Half 15 Q4 Half 20 Q5
O Half 15 Q4 Half 20 Q4 Half 15 Q4 Half 20 Q4
P Half 4 Q4 Half 15 Q4 Half 4 Q4 Half 15 Q4
Q Half 1 Q4 Half 3 Q4 Half 1 Q4 Half 3 Q4
R Half 0 Q4 Half 7 Q5 Half 0 Q4 Half 7 Q5
S CIF 30 Q5 CIF 30 Q5 CIF 30 Q5 CIF 30 Q5
T CIF 20 Q5 CIF 30 Q5 CIF 20 Q5 CIF 30 Q5
U CIF 20 Q4 CIF 20 Q5 CIF 20 Q4 CIF 20 Q5
V CIF 10 Q4 CIF 15 Q4 CIF 10 Q4 CIF 15 Q4
W CIF 7 Q3 CIF 25 Q5 CIF 7 Q3 CIF 25 Q5
X CIF 4 Q3 CIF 10 Q4 CIF 4 Q3 CIF 10 Q4
Y CIF 1 Q4 CIF 3 Q4 CIF 1 Q4 CIF 3 Q4
Z CIF 0 Q4 CIF 7 Q5 CIF 0 Q4 CIF 7 Q5
36
Page 38
User Manual
Chapter 4. Monitoring
When power is supplied to the DVR, images from all channels connected via analog are
displayed on the screen in monitor mode. This chapter describes all DVR features in monitor
mode.
4.1 Default Display
The DVR automatically powers on when
-
the power cord is plugged in.
While the DVR is booting up, all LEDs
-
blink on and off in sequence.
- Once it finishes booting up, the default 16
channel split-screen is displayed (9
channel split-screen for SVR-960C/945, 4
channel split-screen for SVR-480).
※ If a password for the unit has been set, the
password input dialog is displayed.
4.2 Single Display Full Screen
Press a channel button or left-click.
-
Press the [MULTI] button or left-click once
-
again to go back to the split-screen.
4.3 Multi Display
To watch multiple channels simultaneously,
-
press the [MULTI] button or the
button from the Function menu and click
split mode.
- Each press of the [MULTI] button toggles between 4A, 4B, 4C, 4E, 9A, 9B, 10A and 16
channel split-screen modes. The SVR-960C/945 supports 4A, 4B, 4C, 4E, 9A and 9B,
SVR-480 supports 4A.
4.4 Auto Sequencing
To go into auto sequencing mode, set 1 to 16 in the auto sequencing setup or set the desired
channels and then press the [AUTO] button on the front or the
37
button from the Function
Page 39
User Manual
menu. To stop this feature, press the
button again or click Auto to toggle it in the Function
menu.
4.4.1 Default System Mode
Use the button to automatically convert the set channels.
-
- Press the [MENU] button to set the dwell time. Alternately, click the button on the
Function menu.
Go to "Display Setup" on the OSD menu.
-
Go to the "Monitor" submenu under "Display Setup" and press the [Enter] button or left-
-
click.
- Select "Dwell Time" and set a value between 1 and 60 seconds. When this is set to Off,
auto sequencing will not work.
- Auto sequencing mode can be enabled by pressing the [AUTO] button in all split modes.
- To exit auto sequencing mode, press the [AUTO] button once again.
4.4.2 Auto Sequencing Mode
- Press the [AUTO] button. Alternately, click the button on the Function menu.
Set Sequencing from "Monitor" in the OSD menu.
-
38
Page 40
User Manual
1. Up to 16 user modes can be defined.
2. In the image above, 6 sequences are defined with single screen (1) Æ full
screen (16DIV) Æ 4 channel split-screen (4A) Æ single screen (5) Æ single screen
(6) Æ 9 channel split-screen (9A) all being displayed in sequence.
The SVR-960C/945 support 9, SVR-480 supports 4 channel spli t-screen.
4.4 Event Screen
- You can set an event screen to automatically pop up.
- The Event Screen can be set for each monitor.
- To set the dwell time for each event popup, select a monitor and set the dwell time for the
monitor.
- When events occur in several channels simultaneously, the screen automatically splits
into that number of channels. For example, if events occur in 3 channels, event images
are displayed on the 4 channel split-screen. To return to the previous screen, press one of
the channel buttons.
39
Page 41
User Manual
1. If Event Screen is set to Off, event popups will not work.
2. If Event Screen is set to On, the popup image remains displayed until a
button is pressed. To return to the previous screen, press any button.
4.5 Zoom In
- To zoom in on an image, press the [FUNC] button in single display full screen mode,
select the
- When the
image is zoomed in on, it can be moved 18 levels horizontally and 12 levels vertically.
- Use the navigation keys to move the image.
- To return to the previous screen, select the – button and then press the [Enter] button or
left-click.
button, select the + button, and press the [Enter] button or left-click.
button is selected, the default location is the center of the screen. When an
4.6 Live Video Pause
- You can pause a live video feed.
- Press the [PAUSE] button to pause a live video, and press the button again to resume
the live feed.
40
Page 42
User Manual
4.7 PTZ Control
You can control PTZ while watching a video in real time by
connecting the PTZ controller with the DVR and setting the
protocol from the "Serial" menu.
You can either press the PTZ button on the front or press the
[Func] button to execute PTZ.
To control PTZ operation, first select a channel. The selected
channel will be outlined in blue.
Available PTZ and keyboard models are as shown below.
Model Maker
SDZ160/330, Samsung SPD
Keyboard SCC3000, Samsung SRX-100B
BOSCH AutoDome, TC8560X-4 BOSCH
PELCO (P), PELCO (D) PELCO
Honeywell 755/655, HRX-2000, ScanDome2 HONEYWELL
Sony EVI-D3x SONY
VT VPT-4x VT
AD SpeedDome AD
SungJin SJ372R1' SUNGJIN
Samsung SCC641 SAMSUNG ELECTRONICS
SAMSUNG TECHWIN
Panasonic WV-CS850 PANASONIC
LG GAC-PT2 LG
Keyboard KBD300A, WGI SPD1800/2600 WEBGATE Inc.
Merit-Lilin FastDome MERIT
Elmo PTC200C ELMO
Canon VC-C4 CANON
HTC-230S D-MAX
RVision RVISION
Elbex ELBEX
VIDO VIDO
VICON VICON
Hunt HUNT
ORX-1000 SYSMANIA
Fine CRR-1600 LIVEI
41
Page 43
User Manual
Tok in a TO KI N A
Kodicom KRE KODICOM
Nuvico NUVICO
- Press a channel button.
- Press the [PTZ] button on the front or click the button on the Function menu.
- The PTZ menu (Pan/Tilt, Zoom/Focus, Load Preset, Save Preset) will appear.
- Select the desired menu item and then press the [Enter] button or click.
4.7.1 Pan/Tilt
This menu item is used for real-time Pan and Tilt monitoring.
Select Pan/Tilt in PTZ mode.
-
To use pan the camera, press the left or right arrow key on the front or click on the left or
-
right of the screen. To tilt the camera, press the up or down arrow key on the front or click
on the top or bottom of the screen.
4.7.2 Zoom/Focus
This menu item is for real-time Zoom and Focus monitoring.
Select Zoom/Focus in PTZ mode.
-
Use the navigation keys on the front or the mouse wheel to use Zoom and Focus.
-
4.7.3 Load Preset
This menu item is used to go to a preset location in the real-time monitoring mode.
Use the up or down arrow key or the mouse wheel to select a preset number.
-
- Select Load and then press the [Enter] button or click.
4.7.4 Save Preset
This menu item is for setting a new preset location in the real-time monitoring mode.
Use the Pan/Tilt and Zoom/Focus menu items to adjust the camera position.
-
Use the up or down arrow key or the mouse wheel to select a preset number.
-
- Select Save and then press the [Enter] button or click.
4.7.5 Auxiliary On
This is used for special functions of a PTZ device in real-time monitoring mode.
Use the up or down arrow key or the mouse wheel to set an Aux number.
-
- Select On and then press the [Enter] button or click.
- Up to 16 Aux numbers can be set.
42
Page 44
User Manual
4.7.6 Auxiliary Off
This is to stop special functions of a PTZ device.
Use the up or down arrow key or the mouse wheel to set an Aux number.
-
Select Off and then press the [Enter] button or click.
-
4.7.7 Menu
This is used to enter the console menu of the connected PTZ device. The console menu can be
set with the navigation keys and the [Enter] button on the front.
After settings are done, press the [ESC] button or the [PTZ] button on the front to exit the
console menu (available only with the Samsung SPD protocol).
43
Page 45
User Manual
Chapter 5. Playback
5.1 Playback Mode
5.1.1 Playback on Def aul t Display (16/9/4 channel split-screen)
- Press the [PLAY] button or click the button on the Function menu in monitoring mode.
- Press the [PLAY] button or the [FWD] button to play a video at the default 1x speed.
- Press the [REW] button to play a video in reverse at the default 1x speed.
Press the [Play] button in monitor split mode to play videos from 16/9/4 channels.
5.1.2 Playback
PLAY
: Play a video at 1x speed. When using a mouse, click the
PAUSE
STOP
FWD
REW
button in the Function menu.
Pressing the [PLAY] button in monitor mode always plays multiple
videos. Also, pressing the [PLAY] button plays recorded videos from
the last playback timestamp.
: Pause video playback. When using a mouse, click the
in the Function menu.
: Stop video playback. When using a mouse, click the
the Function menu.
: Each press of this button changes the playback speed (in the order
of x1, x2, x4, x8, x16, x32, x64, x1/2, x1, x2 and x4). Pressing the
[FWD] button while viewing a live feed plays the video recorded 1
minute before the current live time. Pressing the
Function menu also changes the playback speed.
: Each press of this button changes the reverse playback speed (in the
button on the
button
button in
order of x1, x2, x4, x8, x16, x32, x64, x1/2, x1, x2 and x4).
Pressing the [REW] button while viewing a live feed plays the video in
reverse from the last recorded frame. Pressing the
Function menu also changes the playback speed.
44
button on the
Page 46
User Manual
STEP FORWARD
STEP REWIND
1/2 REWIND
1/2 FORWARD
: Pressing the [FWD] button while paused plays the video frame by
frame. Press the [PLAY] button to return to normal playback.
: Pressing the [REW] button while paused plays the video frame by
frame in reverse. Press the [PLAY] button to return to normal playback.
: Press the
speed.
: Press the
reverse at 1/2x speed.
button on the Function menu to play the video at 1/2x
button on the Function menu to play the video in
5.2 Search Mode
This menu item is used to search by time or log to play data at a specific time.
Search mode includes Time, Calendar, Event and Thumbnail.
To go into search mode, press the [Search] button on the front or click the [Search] button on
the Function menu.
5.2.1 Time Search
Enter a desired date and time and select Search to go to the video at the specified date and
time.
Start-REC Time
End-REC Time
Search Time
: Displays the date and time when the recording started.
: Displays the date and time of the latest recording.
: Select desired date and time between the recording start time and
45
Page 47
User Manual
the end time.
Search Button
: Search the video for the specified date and time.
5.2.2 Calendar Search
You can search videos more easily with the calendar.
<SVR-1680C/1660C/1645> <SVR-960C/945> <SVR-480>
For the SVR-3200, Monitor 1 displays the recording status from channel 1 to 16 while Monitor 2
displays from channel 17 to 32.
Year
Month
Date
: Select a year. You can use the mouse wheel to change the year.
: Select a month. You can use the mouse wheel to change the month.
: Go to the calendar, select the desired date and press the [Enter]
button. You can use the mouse wheel to search by time.
Time
: Select a time period and press the [Enter] button to start playback.
When using a mouse, select the time and use the mouse wheel to play
the video at the specified time.
5.2.3 Event Search
You can specify a time period and search all channels, some channels, all events, motion
detection or sensors. Use the up or down arrow key on the front to change the date and time.
Alternately, select an item you want to change and use the mouse wheel to change it. The
search results are displayed in a separate list in the event search result window. Select an item
in the search list and press the [Enter] button or use the mouse wheel to go to the specified date
and time and start playback.
46
Page 48
User Manual
Start-REC Time
End-REC Time
Search Start
Time
Search End Time
Event Channel
Event Type
: Display the date and time when the recording started.
: Display the date and time of the latest recording.
: Enter a start date and time to start the search from. Use the
navigation buttons to go to an item, press the [Enter] button and use
the up or down arrow key to change the value. When using mouse,
click an item and use the mouse wheel to change the value.
: Enter an end date and time to search until. Use the navigation
buttons to go to an item, press the [Enter] button and use the up or
down arrow key to change the value. When using a mouse, click an
item and use the mouse wheel to change the value.
: Select a channel.
For the SVR-3200, Ch1 ~ Ch32 are available.
For the SVR-1680C/1660C/1645, Ch1 ~ Ch16 are available.
For the SVR-960C/945, Ch1 ~ Ch9 are available.
For the SVR-480 Ch1~Ch4 are available.
: Select an event type.
You can select all events, motion detection, video loss or text.
5.2.4 Thumbnail Search
Use the up or down arrow key on the front or the mouse wheel to a specify time and search a
specific channel at regular intervals. The search results are displayed in thumbnails. Select a
thumbnail to go to the specified date and time and start playback.
47
Page 49
User Manual
Channel
Start Time
Interval
View Video
Select Video
Changing the I-frame duration may produce results different from your expectation
from Thumbnail Search.
: Select a channel. Use the up or down arrow key on the front or the
mouse wheel to change the value.
: Enter a start date and time to start the search from. Use the left or
right arrow key to go to an item, press the [Enter] button and use the
up or down arrow key or the mouse wheel to change the value.
: Search in a specific interval and display the result. Use the up or
down arrow key or the mouse wheel to change the value.
: Press the [Search] button to display 16 videos in the specified interval
based on the start time. Press the [Func] button or use the mouse
wheel to return to the search window.
: Click a video thumbnail and play it from the specified time. Press
the [Enter] button or click to play the video.
5.3 Copy
This menu item is used to copy a recorded video. There are three types of copy: CD/DVD, RE4
and AVI. To use the Copy function, you must change your permissions in the Security settings.
For more information about changing permissions, please refer to section 6.9.3 on Security.To
copy, press the [COPY] button on the front or click the
5.3.1 CD/DVD
The CD/DVD type uses a CD or DVD to copy a video and detects the CD or DVD automatically.
48
button on the Function menu.
Page 50
User Manual
The SVR-945 is not equipped with a DVD device so you must connect the unit
with an external backup device. Connect an external backup device to the USB
or eSATA port, execute copy and select CD/DVD. On the media list, a CD/DVD device
whose type is [Ext] is displayed. Select the device and make a copy in the same way as
other models.
Type
: Select CD/DVD. Use the up or down arrow key on the front or the
mouse wheel to select it. Press the [Enter] button and use the up or
down arrow key on the front or the mouse wheel to change the value.
Channel
: You can select some or all of the 16 channels. Select the channel
field and press the [Enter] button or use the mouse wheel to select a
channel.
From
: Enter the start date and time for copying. Use the up or down arrow
key or the mouse wheel to set the value.
To
: Enter the final date and time for copying. Use the up or down arrow
key or the mouse wheel to set the value.
Select Disk
: Select the media to copy. Select the Select Disk field and press the
[Enter] button to select the media.
Start
FAT32 Format
: Start copying. Move to the [Start] button and press the [Enter] button
or left-click.
: Format a USB disk or HDD in FAT32.
Do not use this for CD/DVD copying. When using media, you need to
format it first. Select the [FAT32 Format] button and press the [Enter]
button or left-click.
49
Page 51
User Manual
For more information on support media, refer to the table below.
DVD-R Maker CD-R Maker
Mitsubishi (16x recommended) Mitsubishi (16x recommended)
TDK (16x recommended) TDK (16x recommended)
Imation (16x recommended) Imation (16x recommended)
Sony (16x recommended) Sony (16x recommended)
5.3.2 RE4
You can back up videos using HDD or USB storage. You can play them using the mini player or
network manager.
Select the channel field and use the [Enter] button or the mouse wheel to
open the channel list as shown below.
[SVR-3200] [SVR-1680C/1660C/1645] [SVR-960C/945] [SVR-480]
Type
Channel
Select Channel
From
To
Select Disk
: Select RE4. Use the up or down arrow key or the mouse wheel to
select it.
: Select the channel field and press the [Enter] button or use the
mouse wheel to pop up the channel list.
: You can select some or all of the channels. Select a channel on the
channel list and press the [Enter] button or left-click.
: Enter a start date and time for copying. Use the up or down arrow key
or the mouse wheel to set a value.
: Enter the final date and time for copying. Use the up or down arrow
key or the mouse wheel to set a value.
: Select a media to copy. Select the Select Disk field and press the
50
Page 52
User Manual
[Enter] button or click to select a media.
Start
: Start copying. Move to the [Start] button and press the [Enter] button
or left-click.
FAT32 Format
: Format unformatted USB storage devices or HDDs in FAT32 before
copying. Select the [FAT32 Format] button and press the [Enter] button
or left-click.
A backup file that is not 100% complete ca nnot play on a PC properly.
5.3.3 AVI
This type is used to copy a part of a selected channel using USB or HDD storage.
Type
Channel
From
Duration
Select Disk
: Select AVI. Use the up or down arrow key or the mouse wheel to select
it.
: Select a channel. Use the up or down arrow key or the mouse wheel to
select it.
: Enter the start date and time for copying. Use the left or right arrow key
to move between the items and use the up or down arrow key to change
the time and date. When using a mouse, left-click an item and use the
wheel to change the value.
: Specify the duration for copying. Make a copy only for the specified
duration. Use the up or down arrow key or the mouse wheel to specify it.
: Select a media to copy. Select the Select Disk field and press the
51
Page 53
User Manual
[Enter] button or click to select media.
Start
FAT32 Format
If the copied file does not play on a PC, install the unified codec pack.
: Start copying. Move to the [Start] button and press the [Enter] button or
left-click.
: Format unformatted USB storage devices and HDDs in FAT32 before
copying. Select the [FAT32 Format] button and press the [Enter] button
or left-click.
52
Page 54
User Manual
Chapter 6. Setup
6.1 Record Setup
There are 4 DVR recording modes. Their relationship is as shown in the image below, which
briefly describes recording modes.
For more information on recording, refer to the following sections.
Recording
Event Recording Schedule Recording
Emergency Recording
6.2 Time Setup
You need to set the system time before setting recording.
Manual Recording
Setting the time based on your location is very important for the protection of recorded data. It is
53
Page 55
User Manual
not recommended to change the time while recording.
The factory default time zone is UTC 00:00 Dublin.
6.2.1 How to Set Time
If you change the time when recording is already in progress, the time is also
changed for existing recorded videos. It is recommended to back up critical
video data before changing the time.
- Press the [MENU] button on the front or the
- Go to the "Quick Setup" menu.
- Select "Time" from "Quick Setup". Use the [Enter] button or the mouse wheel to select it.
- If you press the buttons in the proper order, the image in 6.2 Time Setup appears.
- Use the navigation keys or the mouse to move to each submenu and press the [Enter]
button or click.
Time Zone
Use the left or right arrow key on the front or the mouse wheel to select your time zone. Each
press of the arrow keys changes the time zone. (To go to the previous menu, press the [ESC]
button on the front or right-click. This is the same for all OSD menus.)
Daylight Saving
This menu is linked to Time Zone. This menu is enabled only when a location with daylight
saving is selected in Time Zone. Daylight saving locations are programmed in the same way as
Microsoft Windows. This menu is used to decide whether to apply daylight saving if the product
is installed in a daylight saving location.
button on the Function menu.
For more information on NTP, refer to "NTP" of Network Setup.
Date Format
Select the date format. Use the left or right arrow key or the mouse wheel to select
"MM/DD/YYYY", "YYYY/MM/DD" or "DD/MM/YYYY".
Time
Use the left or right arrow key to move between year, month, date and time. Use the up or down
arrow key or the mouse wheel to set each item.
54
Page 56
User Manual
Apply
You must press the [Apply] button to save the Date/Time values. Then, the dialog box below
appears.
Setups other than "Date/Time" setup are automatically recorded if the menus are
completely closed, but "Date/Time" setup is not automatically recorded because
it may damage the HDD recording file system. Be sure to press the [Apply]
button to apply changes.
6.3 Camera Setup
This menu is used to set the conditions of each camera connected to the unit.
You can use the camera setup menu to adjust [Title], [Status], [Color], [AGC], [Brightness],
[Contrast] for each of the connected cameras. The set values apply to monitoring and search in
the same way.
For more information on each menu item, refer to the following sections.
NTSC and PAL cameras cannot be used for the unit at the same time. For
example, you cannot connect NTSC cameras to 1CH to 5CH while connecting
PAL cameras to 6CH to 16CH. Also, when replacing NTSC cameras with PAL
cameras, you must reboot (power on/off) the unit after c onnecting the PAL
cameras for proper recognition.
The set values apply to monitoring and search in the same way.
55
Page 57
User Manual
6.3.1 How to Set a Camera
Press the [MENU] button and use the navigation keys or the mouse wheel to select a desired
channel from the "Channel" menu under the "Display" menu of Display Setup.
Title
Specify the camera name.
Press the [Enter] button or click to open the character input menu.
When inputting a string, the character input window appears.
The character input window may differ depending on the menu, but the character input method
is the same.
Use the navigation buttons to input characters.
-
When using a mouse, click a character.
-
Press the navigation buttons to select characters.
-
After selecting characters, press the [Enter] button to input them.
-
To delete characters, press the [Í] button to move back.
-
To insert a space between characters, press the [Î] button to insert a space.
-
Channel Status
You can enable or disable a camera.
56
Page 58
User Manual
Press the [Enter] button and use the left or right arrow key or the mouse wheel to select
"Enable" or "Disable".
To increase recording or network monitoring speed, be sure to disable unused channels.
Color
Press the [Enter] button and use the left or right arrow key or the mouse button to select "Color"
or "B/W".
AGC (Auto Gain Control)
AGC is used to automatically control the input range of video signals from a camera.
Press the [Enter] button and use the left or right arrow key or the mouse wheel to select
"Enable" or "Disable".
Brightness / Contrast
You can adjust the brightness and contrast of a video.
Press the [Enter] button and use the left or right arrow key or the mouse wheel to select a value
between "-9" and "+9".
6.4 Monitor Setup
This menu is used to set related items when displaying a video on the monitor.
Monitor 1 & Monitor 2~4 (SVR-3200/1680C/1660C)
Monitor 1 is available for all supported functions of the DVR while Monitor 2~4 are available for
all functions other than playback and search.
Monitor 1 & Monitor 2 (SVR-1645/960C/945)
57
Page 59
User Manual
Monitor 1 is available for all supported functions of the DVR while Monitor 2 is available for
event popup, user sequencing and split screen.
Covert Channel
This menu is used to hide channels in live mode.
The Covert Channel menu shows the unit's channel list. Press the [Enter] button or click to
select a channel. The selected channels then do not show videos in live/playback modes.
Auto Sequencing
This is for editing the auto sequencing function. The 16 available sequencing modes have a
dwell time between 1 and 60 seconds.
Multi Display
This menu is used to define the multi display of 4E (4 channels), 9B (7 channels) or 10A (10
channels) in advance. For the SVR-960C/945, only 4E (4 channels) can be defined.
To set multi display, select the target and the window on its right, use the [Enter] button or the
mouse wheel to open the window, and press the [Enter] button or click to select a channel.
Then, press the [ESC] button or right-click.
※ SVR-480 does not support to set multi display.
VGA Mode
Three VGA modes are provided for VGA monitors. The available modes are 800x600, 1024x768
and 1280x1024.
On Screen Display
This determines what information is displayed for live video feeds or video playback.
For live video feeds, you can set the time, channel name, event, recording status, HDD, remote
control ID and text. For video playback, you can set the time, command, channel name, event
and text display.
6.5 Record Setup
Three different recording options are available: Schedule Recording, Manual Recording, and
Event Recording. Schedule Recording records video automatically at a scheduled time. Manual
Recording enables you to record video manually by pressing the "REC" button. Event
Recording records video when an event occurs if the Program and Event Check settings are
activated.
58
Page 60
User Manual
6.5.1 Program Setup
Using the [Program] menu, you can set up a program to use for both Manual & Event and
Schedule & Event. You can adjust the frame rate, video quality and resolution of the program.
Two choices are available: 1) Select a program by the frame rate, quality, and resolution, or 2)
Set up a program manually. For Event Recording, you can select a frame rate up to the
maximum possible for one channel. When events occur simultaneously in more than two
channels, the recording frame rate may be automatically adjusted.
Program
Under the Program menu, a total of 26 programs labeled from A to Z are available for you to define
with the recording resolution and quality for each channel. For more information about the setting
values of the Program menu, please refer to section 3.5.
Ch (Channel)
Indicates a channel number.
R (Resolution)
Indicates the recording resolution. A total of three types are available: D1 (704x480), Half D1 (704x240),
and CIF (352x240).
F (fps)
Indicates frames per second: from 1 to 30fps. The maximum frame rate may vary depending on
settings.
59
Page 61
User Manual
Q (Quality)
Indicates the recording quality: Q5, Q4, Q3, Q2, and Q1. For Event Recording, Q3 or higher is
recommended.
Max R/F
Indicates the maximum frame rate available for a selected resolution. For instance, CIF 30fps
means that you can select up to 30fps for the CIF resolution of a selected channel. D1 30fps
means that you can select up to 30fps for the D1 resolution.
How to Calculate Recording Performance
D1 [704x480] = 2 x Half D1 [704x240] = 4 x CIF [352x240]
120 D1 compressed frames = 240 Half D1 compressed frames = 480 CIF
compressed frames
The resolution and maximum frame rate vary depending on the number of enabled channels.
• When disabling a channel in the Channel settings
How to Disable: Select Menu > Camera Settings > Use Channel > Disable. (The channel is then
grayed out to show that it is disabled.) For example, the SVR-1660C can record every channel at up to
CIF 30fps. If a channel is "Disabled" in the Channel settings, there is then a surplus of CIF 30fps
recording capacity. You can use the —surplus CIF (352x240) 30fps to increase another channel's
resolution to Half D1 (704x240) 30fps (remember from above that CIF x 2 = Half D1).
• Setting a channel's frame rate to "0fps" in the Program settings
Surplus CIF 30fps cannot be used to increase another channel's resolution because the 0fps
channel still uses at least 2 to 3 recording frames per second for various reasons
including network communications. You must disable the channel instead of setting it to
0fps if you want to conserve and use the surplus CIF 30fps recording capacity for
another channel.
Relation Between Normal Recording and Event Recording
When an event occurs, Event Recording is activated with the Program settings. DVR
recording performance varies depending on the model. For example, the recording performance
of the SVR-1660C is CIF 480fps for both Normal and Event Recording. When both recording
modes are in effect, its recording performance cannot exceed CIF 480fps. That means that
Event Recording can be set up for the SVR-1660C only if the total of Event and Normal
Recording of all channels does not exceed CIF 480fps.
60
Page 62
User Manual
• Event Settings in and CIF 480fps Recording Performance
When every channel is set up to record normally at CIF 30fps, the Event Recording settings
of for 1
st
channel are limited to CIF 30 fps, Half 15 fps, and D1 7fps. If you want to set the Event
Recording settings value to D1 30fps, the Normal Recording settings value of the other
channels must be changed to total CIF 360fps or less.
• When Events Occur in Multiple Channels Simultaneously
When events occur simultaneously in multiple channels and the Event Recording settings value
exceeds the DVR's maximum recording performance, the Normal Recording settings value is
retained, and the channels with events drop their Event Recording frame rates settings to
record the events.
The SVR-1680C provides D1 30 compressed frames for all channels; it can record programs
at a manually selected resolution and frame rate at all times.
Quick Record Setup (Quick Setup)
Quick Setup provides recording, language, time and audio setups in one place.
How to Set Quick Recording
Select 'Quick Setup'.
Program Setup
All programs are set to 0fps by default so each program needs to be set individually (described
in details in recording menu).
61
Page 63
User Manual
Schedule & Event Setup
Set record mode to "Schedule & Event" and set a schedule and event for each date and time.
How to Check Recording
If record setup is properly completed, the 'REC LED' on the front will flicker. Also,
[S] is displayed to show that currently all channels are recorded as scheduled.
6.5.2 Manual/Schedule Recording Setup
You can switch between Manual and Schedule Recording by changing the recording mode.
Both Manual and Schedule Recording enable you to choose a program to record. The
resolution, frame rate, and quality may vary depending on the selected program.
62
Page 64
User Manual
Manual Recording
Manual Recording is activated only when the recording mode is set to Manual & Event. After
selecting a program, press the [REC] button on the front of the DVR unit to begin recording. If
you want to schedule a recording, switch the recording mode to Schedule & Event.
Schedule Recording Settings
Schedule Recording records video automatically at a scheduled time according to the chosen
program settings. Set the recording mode to Schedule & Event then select a program for a
scheduled date and time.
.
When selecting a program, the default settings value of the program is displayed for you to
confirm. You can select one or more programs from among the 26 available, all labeled from A
to Z. The picture below shows an example using only Program A.
63
Page 65
User Manual
• Index: 1~50 different programs can be set
• Day: designate recording date
• Program: select a recording program (A~T)
• Time: designate recording time
• Delete: delete the desired INDEX
Setting Method
As you set INDEX, DAY, PROGRAM and HOUR, then the content will be immediately displayed
in the table. If you select the start time and the stop time for recording in the table and click on
them in order, the content will be displayed in INDEX, DAY, PROGRAM and HOUR.
Deletion Method
Select the desired INDEX and then click on the Delete button. If you click on the Delete button
before selecting INDEX, then the content of INDEX that was selected previously will be deleted
first. After that, the content in the highest INDEX will be deleted and then others INDEX will be
deleted in the increasing order of INDEX.
Editing Method
Select the INDEX to be edited and then change DAY, PROGRAM and HOUR on your own.
If all the INDEX fields up to INDEX 50 are already set, then click on the time in the table to be
edited with your mouse. Click on the hour in the table to be changed, again with your mouse.
The previous setting will be deleted and overwritten with the change that you have just made.
If the same time is set twice then ‘!’ will be displayed in the table.
64
Page 66
User Manual
When you set the region of time, you may not include the existing time that
is set previously.
Record Setting
Repeat Record Mode
When there is no more space for recording to hard disk, recorded data is removed from the
foremost portion automatically.
Warning Level
This checks the capacity of all disks connected to the DVR and gives a warning when the
specified level is met.
Recorded Data Retention
This shows videos recorded only on specified dates in hard disk.
For example, if the entire video is recorded for 10 days (Drawing 1) and only 2-day recording
(Drawing 2) is specified for playback, only the 2-day recording is available for playback.
Playback Deinterlace
This turns playback deinterlace on or off.
This is available only when the recording resolution is set to Full D1. If this is set to On, imaging
shaking decreases while Full D1 video is paused.
6.5.3 Evnet Record Setup
This menu item is used to record video based on events. To use Event Recording, select a
resolution, frame rate, and quality from the available 26 programs.
Event recording is divided into recording by sensor, by motion detection, by text and by digital
input. In the Programs settings, select a program first. If you want to adjust the details of a
program, select the program and then adjust the resolution, frame rate, and quality. (For more
information, please refer to section 6.6.1 on Program Settings.)
65
Page 67
User Manual
Event Recording is used mostly in conjunction with other recording options: Manual & Event
and Schedule & Event.
Go to [Record Setup] > [Record]. In "Record Mode," select Manual & Event or Schedule &
Event.
To use Event Recording only, please refer to the following instructions.
1. In Record Mode, select Manual & Event or Schedule & Event.
2. In the Program settings, change the frame rate of Normal Recording to 0 and
of vent Recording to the desired rate.
3. Set an Event Check to activate the recording.
Event Check Settings
This menu item sets times for event recording and has the options of Always, Disable and
Timezone. The "Always" option always detects events while the "Timezone" option uses events
only for specified hours. When Timezone is selected, a setup similar to schedule setup is
possible; the event check time can be set by the hour.
66
Page 68
User Manual
• INDEX : 1~50 different programs can be set
• Day: designate recording date
• Time: designate recording time
• Delete: delete the desired INDEX
Setting Method
As you set INDEX, DAY, and HOUR, then the content will be immediately displayed in the table.
If you select the start time and the stop time for recording in the table and click on them in
order, the content will be displayed in INDEX, DAY, and HOUR.
Deletion Method
Select the desired INDEX and then click on the Delete button. If you click on the Delete
button before selecting INDEX, then the content of INDEX that was selected previously will
be deleted first. After that, the content in the highest INDEX will be deleted and then others
INDEX will be deleted in the increasing order of INDEX.
Editing Method
Select the INDEX to be edited and then change DAY, and HOUR on your own.
If all the INDEX fields up to INDEX 50 are already set, then click on the time in the table to be
edited with your mouse. Click on the hour in the table to be changed, again with your mouse.
The previous setting will be deleted and overwritten with the change that you have just made.
67
Page 69
User Manual
6.6 Audio Setup
This menu is used to set audio recording, sync or mixing.
6.6.1 Audio
This menu is used to set the audio channel, audio recording, audio gain and sync.
Audio Channel
Select a channel for audio.
Audio Recording
Decide whether to record audio. If No is selected, audio is outputted only for live video feeds. If
Yes is selected, audio is outputted even for playback.
Audio Gain
This menu is used to adjust audio volume up or down.
Sync Video Channel
This menu is used to determine which channel the input audio is linked to for output. This is
available only for recording. Audio output for live video feeds is described in Audio Mixing. If
Sync Video Channel is set to 5 for Channel 1 audio, the audio inputted into Channel 1 is
outputted when Channel 5 is selected. By default, Channel 1 audio is outputted to Channel 1
video.
68
Page 70
User Manual
6.6.2 Audio Mixing
This menu is used to select audio for live video feeds. If All is set, all inputted audio is mixed for
output regardless of channel selection. If specific audio is selected, only the specified channel is
outputted regardless of the channel selection.
6.7 General Event Setup
This menu is used to set events that you want to use.
Motion Detection Setup
This menu is used to save events occurring through motion detection for each channel.
※ SVR-480 does not support Digital I/O
69
Page 71
User Manual
Motion Detection
This enables each channel or all channels to detect motion and notify users.
- Channel
Channel can be set to All or as follows.
SVR-3200: 1~32CH
SVR-1680C/1660C/1645: 1~16CH
SVR-960C/945: 1~9CH
SVR-480 : 1~4CH
- Sensitivity
Sensitivity can be set to Lowest, 1~10, or Highest for each channel.
- Area
Area is used to set the motion detection area.
If Channel is set to All, Area can be set to Set All or Unset All. When each channel is set
individually, Area can be set to Set All, Unset All or User Defined.
- User Defined
User Defined is only available when each channel is set individually. It is used to set an
area where you want to detect motion intensely.
It allows you to set a user-defined motion detection area. You can select one or more
motion detection areas out of the squares on the 22x15 grid.
The default setting is "Set All". Press the [Area Setup] button to open the motion detection
area setup window.
Users can specify motion detection areas on the screen.
The setup window composed of 330 squares in a 22x15 grid appears. Squares set as motion
70
Page 72
User Manual
detection areas turn gray. To select motion detection areas, use the navigation buttons to select
them and press the [Enter] button or click them. Press the [ESC] button or right-click to return to
the previous menu.
Sensor
A total of 16 sensors (9 sensors for the SVR-960C/945, 4 sensors for the SVR-480) can be set.
If All is selected, all channels are set to N.O or N.C. You can select channels and set them
individually to N.O., N.C. or Off.
6.7.1 Text Setup
Recording
You can turn recording for text input on or off.
Sync Text With
This selects channels to link with text data.
Seek Header
This parameter is not needed if, just like Star Finger-007, protocols are already registered and
supported for various types of data that comes from external devices (Access Control, POS,
ATM, etc.). However, this parameter is needed to see how one unit of data out of continuously
incoming text data is structured. In other words, all data has its start and end points, and the
header is data that is always inserted to indicate the start point. Therefore, by defining a header
here, the DVR can recognize from the header that it is the start point of the data. Two headers
can be set and detected because one device can send various types of data to external
receivers.
Delimiter
The delimiter value may differ depending on the device used. For more information on delimiters,
refer to the user manual or the device manufacturer.
Timeout (ms)
Lines defined below are the maximum number of text lines available for one piece of data. Even
though data is standardized, lengths may differ. For example, three lines are programmed for
client name input for an ATM, but if someone registers only his/her first name and last name,
only two lines are provided when the person uses an ATM. However, the DVR cannot detect this
automatically, so Timeout is used to determine how long is needed to recognize the received
data as complete data after the last line is entered.
71
Page 73
User Manual
Lines
This defines the maximum number of lines for one piece of data.
An external device may not be recognized depending upon it s characteristics,
so it is recommended to contact the manufacturer before installation.
6.7.2 Preset
This menu is used to activate the presets specified in the PTZ based on sensor input.
Specify a preset with PTZ attached to each channel.
Select a channel in the preset menu and select an event for the preset.
You can choose sensor, MD or text for an event, and 16 presets can be set.
72
Page 74
User Manual
6.7.3 Digital I/O
Digital I/O are digital ports available for input and output at the same time., There are 12 digital
inputs and outputs.
Digital I/O Channel & Input/Output
All 12 channels can be set to input/output. When channels are set to input, if an input signal is
received by even one channel, emergency recording will operate. When they are set to output, if
sensor input is received, it will operate.
In Digital I/O Setup, if you set one of the 12 Digital I/O to [Input], set Input Type to [Emergency]
and turn Digital I/O on, the emergency recording will operate. The macro set in the event
recording is used for the recording. The recording will continue based on the value set in
[Recording After Event] under Event Recording and then stop.
※ SVR-480 does not support Digital I/O.
73
Page 75
User Manual
6.7.4 Event Action
This sets actions based on event input.
Event Action
For Event Action, you can select Relay 1~4, buzzer, or E-Mail.
Action Duration
Action Duration is used to maintain an action for a specified time when relay or buzzer is set. If
E-Mail is set, e-mails are sent in specified time intervals.
Normal Event Source
You can set Normal Event Source to 16 Sensors, 16 MDs, 16 Video Losses and Text,
Emergency.
※ SVR-480 does not support Digital I/O, thus it does not display “Emergency” on select mode.
74
Page 76
User Manual
System Event Source
This sets some or all of disk error, disk full, fan error, authentication failure and DDNS
registration failure.
E-Mail Setup
E-Mail address is set when e-mail is used for output.
For e-mail address, enter an e-mail address for a message recipient.
The address format is xxxx@xxxxxx.xxx
. However, only Roman alphabet letters and numbers
are allowed.
- Sender Address
Sender Address is set when e-mail is used for output. The address format is
xxxx@xxxxxx.xxx
. You do not have to enter an e-mail address. In general, use an address
that identifies the e-mail as being sent from a specific DVR.
75
Page 77
User Manual
- Attachin g Image Files
For a Normal event log, the system sends an e-mail attached with an image of the event
channel along with the event information including the sensor, movement detection, and
object disappearance.
For a System event log, the system sends only the event information because the channel
pairing option is not available.
6.8 Network
This sets network information when connecting the DVR to a network.
Type
76
Page 78
User Manual
This is used to select the network type (Ethernet/xDSL) connected to the DVR. Select Ethernet
when the DVR is connected to dedicated line, cable modem or LAN.
Select xDSL when the DVR is connected to a PPPoE-type xDSL line. However, if the xDSL line
is not of the PPPoE type, you must select Ethernet.
DHCP
Dynamic Host Configuration Protocol (DHCP) manages host addresses on a network. All the
hosts on a LAN use this protocol to share limited IP addresses when accessing the Internet. In
other words, a DHCP server allocates dynamic IP addresses to all the hosts on the LAN.
If the LAN has its DHCP server and the DHCP menu item is enabled, the DHCP server
allocates an IP address to the DVR.
'DHCP' is used on a LAN with a DHCP server installed. Generally, small and large LANs have
DHCP servers while small LANs use Network Address Translation (NAT) from a hub or router.
IP Addr
IP Address is used for communication between the DVR and Network Manager, and is also
used when Webviewer accesses the DVR. This is available only when Net Mask and Gateway
are set.
Net Mask
Net Mask specifies a range of IP addresses and enables IP addresses in the range to
communicate. Net Mask should be allocated by a network administrator.
Gateway
Gateway must be specified to enable IP addresses to communicate and should be allocated by
a network administrator.
DNS1
DNS1 must be specified to register the DVR to SWR while DNS Address should be allocated by
a network administrator.
Additional DNS
Additional DNS is used to replace DNS1 when it is unstable or has a problem.
Port
77
Page 79
User Manual
Port is used to register to SWR, connect to Network Manager, or connect to Webviewer.
The default port is 4000. Be careful about the port entry when a PPPoE modem
Internet sharing device are in use.
Bandwidth Limit (Mbps)
This sets the maximum transmission speed of data outputted from the DVR, or the data
transmission capability of the DVR. This may be left blank. Ask your network administrator to
specify it when necessary.
6.8.1 xDSL
If the DVR is connected to xDSL and uses PPPoE, set Type to xDSL and specify a user ID and
password. You must use the user ID and password given when you subscribed to the xDSL
service.
User ID/Password
If the DVR is connected to xDSL, you must specify a user ID and password.
Status
This shows the connection status of the DVR.
6.8.2 DDNS
If the DVR is connected to a cable modem or an xDSL modem, a new IP address will be
assigned each time the device connects to the ISP. In such a case, the user may not be able to
find out the DVR's IP address. By registering a DVR with a dynamic IP address to a DDNS
78
Page 80
User Manual
server, the DVR's IP may be identified by connecting to the DDNS server.
To register a dynamic IP address to a DDNS, follow the instructions shown below.
DDNS Registration procedure
1) Sign up at iPOLiS homepage.
- The homepage URL is [www.samsungipolis.com]
- Accept the terms and conditions, SIGN UP page: check ID availability
2) Register the product after sign up.
- Log on to iPOLiS website
79
Page 81
User Manual
- Product List (If you didn’t register products, there are no list)
- Product Registration (Check ID availability), Information regarding the registered
products may be reviewed from the list
80
Page 82
User Manual
3) Configure the product for DDNS
From the DVR's Network Setup menu, configure the settings as shown below. Select Menu and
Network to prompt a screen similar to the illustration shown below. Set DDNS to "On" and input
the DDNS address in 'DDNS SERVER DOMAIN NAME'. (The default value is
www.samsungipolis.com.) For ID and PW, use the user ID (domain) and password used in
iPOLiS product registration process.
This concludes the necessary configurations to the DVR for DDNS connection.
4) The connection status of product can be checked on the product list.
81
Page 83
User Manual
- The Product list will display status 'On' for the connected device
[VIEW]: See the log-in page of selected product
[Edit]/ [Delete]: Edit/Delete the selected product
Once the product has been registered, its ID (domain) may not be changed. When the
product’s ID needs to be changed, the product’s registration must be reset. Register the
product again with the new ID.
To register a fixed IP address to a DDNS, follow the instructions shown below.
Interval
To maintain continuous registration status, a registration cycle must be assigned from "Interval".
82
Page 84
User Manual
A dynamic IP address will renew the relevant data from the DDNS per each interval. If the user
sets the registration interval to "Disabled" or the DVR does not upload any information over two
days, information regarding the DVR will be removed from the DDNS database.
Server
This menu is used to configure the server address to be registered. The address of the SWR is
www.samsungipolis.com.
ID
Use the ID for the DDNS login.
Password
Use the password for the DDNS login.
Status
The DVR's registration status is indicated. "Not Registered" means that the DVR is not
registered to the DDNS. "Date/Time & OK" means that the DVR has been registered to the
DDNS.
6.8.3 NTP
Network Time Protocol (NTP) synchronizes time between devices on network. On a network,
there is a server that provides the base time and clients that receive the time from the server for
synchronization.
Sync With NTP
83
Page 85
User Manual
This turns NTP on or off.
NTP Mode
This sets NTP Mode to Client, Server or All.
NTP Server Location
This is enabled when NTP Mode is set to Client. This determines whether the NTP server is on
a local network or on the Internet.
NTP Local Server IP
This is enabled when the NTP Server Location is set to Local and is used to set the IP of the
NTP server. Enter either the IP of an NTP server on the local network or the IP of a DVR with its
NTP mode set to Server.
Interval
This menu is used to set the synchronization interval.
When NTP Mode is set to Client, Sync With NTP must be set to On.
6.8.4 Remote
DVR ID
This sets the address of the keyboard when operating all DVR functions with the controller
buttons. The default value is "1". If one keyboard is connected to several DVRs, it might conflict
with other channels, so a different value should be set for the keyboard address.
84
Page 86
User Manual
Remote Controller ID
Up to 16 remote controller IDs can be set. You can use one remote controller to operate up to
16 DVRs.
How to register the remote controller is as shown below.
- Direct the remote controller to the DVR.
- Press the [ID] button based on the specified remote controller ID.
- If the remote controller ID and the DVR ID are the same, the DVR buzzer beeps.
- The remote controller is now configured and available for use.
Remote Configuration Setup
This determines whether to use the SNM Configuration program for setup.
If "Enable" is set, SNM Configuration is available for setup. If "Disable" is set, SNM
Configuration is unavailable for setup.
Remote Relay
Remote Relay is used to determine whether to use the Relay On/Off function on the SNM
monitor.
If "Enable" is set, all four relays can be controlled remotely. If "Disable" is set, remote
control is unavailable with the SNM Configuration.
6.8.4.1 Serial Port
A total of four serial ports are available for the DVR. Two are RS-232C(Com1, Com3) and the
other two are RS-422/485(Com2, Com4).
The Serial Port settings are available under Communication > Remote.
The following options are provided for the Serial Port settings.
※ A total of 3 serial ports are available for SVR-480. One is RS-232C(Com1), and the other
two are RS-485(Com2,3).
85
Page 87
User Manual
6.8.4.1.1 Text
To use the Text option, please follow the instructions below.
Please note that the Text option supports only Com1 (RS-232); make sure to select Com1 on
the Serial Port menu.
Device
Select Text.
Interface
Select RS-232.
Baud rate/Parity/Stop Bit/Data Bit
Enter the same settings as the ones for the selected TP device.
6.8.4.1.2 Transparent
To use a transparent device, please follow the instructions below.
86
Page 88
User Manual
Device
Select a connected transparent device.
Interface
Select COM1 or COM3.
※ Only Com1 is available for SVR-480.
Baud rate/Parity/Stop Bit/Data Bit
Enter the same settings as the ones for the selected Transparent device.
6.8.4.1.3 Keyboard
To set up a keyboard, select Keyboard for the Device option, and then select a keyboard model.
Device
Select Keyboard.
Keyboard
Select a desired keyboard model.
Interface
87
Page 89
User Manual
Select COM1 or COM3.
※ Only Com1 is available for SVR-480.
Baud rate/Parity/Stop Bit/Data Bit
Enter the same settings as the ones for the selected keyboard.
6.8.4.1.4 PTZ
Select PTZ.
To control the PTZ operation via serial port, select PTZ in the Device options, and then set up
a serial port; refer to 6.8.4.2.2 PTZ (Serial).
To control the PTZ operation via coax protocol, you do not need to set up this option. (Refer to
6.8.4.2 PTZ.)
Device
Select a connected PTZ device.
6.8.4.2 PTZ
Two PTZ control methods are available: via serial port and coax protocol.
88
Page 90
User Manual
6.8.4.2.1 PTZ(Coax)
The Coax Protocol option does not support normal PTZ protocols, but rather supports the Pelco
Standard and Extended Protocols.
The standard protocol supports basic PTZ functions such as PTZ and presets. The extended
protocol supports more expansive features such as menu control and video playback in addition
to the basic PTZ functions.
To use this option, a PTZ device must be embedded with a coax standard or extended protocol.
※ SVR-3200, SVR-1645, SVR-945, SVR-480 does not support coaxial function.
Type
Select Coax.
Protocol
Select Pelco or Pelco Extended according to the coax protocol type of Pelco camera.
AD Dome does not support menu control, Presets or AUX when setup with a
coax protocol.
Idle Time
Activate or disable PTZ Home, and setup a standby duration of the device before moving to
PTZ home.
6.8.4.2.2 PTZ(Serial)
Select PTZ.
89
Page 91
User Manual
Type
Select a serial port.
Protocol
Select a connected PTZ device.
Camera ID
Enter the ID of the selected camera.
Interface
Select one from among Com2 to 4.
To use RS-232, select Com3. For RS-422 or 485, select Com2 or 4.
Baud rate/Parity/Stop Bit/Data Bit
Enter the same settings as the ones for the PTZ device.
Idle Time
Activate or disable PTZ Home, and set up a standby duration for the device before moving to
PTZ home.
For more information on cameras supporting PTZ and how to set them up, refer
to "4.8 PTZ Use".
6.9 System Setup
90
Page 92
User Manual
6.9.1 System Setup
Language
The OSD menu supports multiple languages. Select a language.
Key Buzzer
This determines whether to use the buzzer for the buttons on the front.
Default
This restores the factory default settings. Press the [Default] button to restore the factory default.
Load Configuration
This sends the DVR setting stored in a USB storage device to the DVR.
Save Configuration
This saves the DVR setting to a USB storage device.
Firmware Update
Save the Update Firmware for USB to USB storage and connect it to the DVR.
Select Firmware Update from System Setup and press the [Enter] button.
When a message prompting you to update appears, select [Yes] and press the [Enter] button.
After a while, a buzzer beeps and the unit reboots.
The Update Firmware for USB is provided in a "*.dat" file.
To do a firmware update through the network, run the updater executable file and click a DVR
on the DVR list. When the IP, MAC address and port of the DVR are displayed, enter the
91
Page 93
User Manual
password (default: 11111111) specified in SNM-128S into "Admin Password" and press the [Start
Upgrade] button.
After the upgrade progress window appears, a message prompting you to reboot the unit is
displayed. Select "Yes" to reboot the unit.
DVR Alias
This sets a DVR alias.
System Log
The system logs various events including changing menu settings, turning the power on or off,
changing the time zone, turning HDD on or off, using the Copy function, and when system
events occur.
You can check log details with the >> icon by pressing the Enter button or scrolling the mouse
wheel.
92
Page 94
User Manual
Copying System Log
System logs are saved as txt-formatted files, and can be saved to a USB flash drive.
To save system logs to a USB drive, insert the drive into a USB port, open the System Log list.
And then press the "COPY" button on the front.
The data will be saved as "Model Name_System Log_Date&Time.txt."
Time
This is used to set the time zone, date format, and time for the DVR.
Daylight Saving needs to be set depending upon the region.
I-Frame Duration
An I-frame duration is the interval between I-frames and is measured by the video frame rate.
For video recordings with less motion, I-frame duration enhances the video quality.
You should only set I-frame duration settings to anything other than Auto if you are specialized
in MPEG-4.
6.9.2 Disk
This section describes how to add, remove, or format internal and external hard disks.
93
Page 95
User Manual
Disk Manager
Disk Manager is used to manage internal and external HDDs.
It manages HDD status, bad blocks, size, enabled, disabled, etc.
Type
Model
Bad Block
: Displays disk locations and types.
Int A (Internal A HDD), Int B (Internal B HDD), Ext (External HDD)
: Displays HDD models.
: Displays HDDs with bad blocks. 0 is displayed when there are no
problems. Nothing is displayed for HDDs not in use.
94
Page 96
User Manual
Size(MB)
Enabled
: Displays HDD sizes in MB.
: Enables or disables HDDs.
Yes: Enabled / No: Disabled
To change HDD to Yes
- Enabled: Select No and press the [Enter] button or use the mouse wheel to open the notice
window with the following message.
- "Warning: This disk is usable without being formatted. Do you want to format the disk
anyway?"
- Select No to keep the previous data stored in the HDD and change it to Enabled-Yes.
- Select Yes to delete the previous data stored in the HDD and change it to Enabled-Yes.
To change HDD to No
- Enabled: Select Yes and press the [Enter] button or use the mouse wheel to open the notice
window with the following message.
- "Warning: Do you want to remove the disk?"
- Select Yes to open the "The disk has been removed." message and change the HDD to
Enabled-No.
- The HDD is now unused.
- Select No to keep the HDD as it is.
Disk Status
This displays the temperature and status for each HDD.
6.9.3 Security
DVR users are divided into administrators and general users. Administrators can use all DVR
95
Page 97
User Manual
features without any limitations. The maximum number of users is 10. They can only use
features that they have permissions for.
Right
In Right Setup, if Check is set to all X, all users can use all features without any limitations.
If Check is set to all O, each user can use only features for which they have been given
permissions.
In the image above, User 1 & 2 can use only “O” function. You can set User 1 to User 10 in the
same way.
Admin Password
The def a u lt Ad m in Pa ss wo r d i s " 11111111" and can be changed. The Admin Password should
be an 8-digit number.
User Password
User 1's password is "11111111", User 2's is "22222222", and similarly for User 3 to User 9. User
96
Page 98
User Manual
10's password is "00000000". The 16 channel-DVRs do not have a [0] (zero) button so they
use the [10] (ten) button instead.
Change Password
As shown in the image below, click Change P/W for a user you want to change.
The password input window appears. Use the number buttons on the front or the character input
window to enter a new password.
Click the [Change] button to save it.
Clicking the [Change] button displays a popup confirmation window that prompts you to change
password. Click Yes.
The password has been changed.
Permissions
Using permission restricted features requires a password check. Execute a command to open
the password input window. Select a user and enter his/her password. Now the function is
available.
[Permission check]
6.10 Exit
This exits with or without saving menu settings.
97
Page 99
User Manual
Save
This saves all settings and exits to the live screen.
Select Yes to save all settings and exit, or select No to exit without saving any settings.
Do not save
This is used to exit without saving any settings.
98
Page 100
User Manual
Chapter 7. Web Viewer
Web Viewer is a web application provided as a complement for the DVR, capable of receiving
visual live feeds and playing recorded data from a distance over the Internet. Web Viewer's
structure consists of the log-in page, monitoring monitor and playback monitor. Detailed
descriptions of the components are as follow.
7.1 System Requirements
Minimum Recommended
CPU Intel Pentium 4 / 3.0GHz Core2duo E6750 or higher
Main Memory 1GB 2GB or higher
Video Memory 128MB 512MB or higher
Display Resolution 1280 x 1024 (with 32bit color) or higher
HDD 1GB or higher
OS Windows XP Professional / Window Vista Business
Others DirectX 9.0 or higher
7.2 LOGIN
Use the IP address and port assigned to the product to access the Web Viewer Log-in page.
The URL to access the page will be similar to http://192.168.1.100:4000. If the port value has
been changed from the default value of 4000, use the changed value instead after the colons.
Use the ID and password from SNM-128S and click "Login". The default ID and password are
[admin] and [11111111] (eight ones). The password may be changed, but the ID may not.
To change the DVR's administrator password or issue new user ID and password,
refer to "7.3 Connection User Setup".
99
Loading...