SAMSUNG SVR-659, SVR-150, SVR-251W, SV-DVD2EK, SV-DVD6E Service Manual
...
TS-10A DECK
1. Disassembly and Reassembly
2. Alignment and Adjustment
TS-10 DECK CONTENTS
♦ File with the SERVICE MANUAL.
MECHANICAL MANUAL TS-10A DECK
ELECTRONICS
© Samsung Electronics Co., Ltd. DEC. 2001
Printed in Korea
AC82-00023A
MECHANICAL
Manual
Samsung Electronics
1-1
Œ
´
ˇ
¨
ˆ
Ø
Fig. 1-1 Top parts Location-1
ΠGEAR FL CAM
´ MOTOR LOADING ASS’Y
ˇ LEVER FL ARM ASS’Y
¨ HOLDER FL CASSETTE ASS’Y
ˆ LEVER FL DOOR
Ø SLIDER FL DRIVE
1. Disassembly and Reassembly
1-1 Deck Parts Locations
1-1-1 Top View
1-2
Samsung Electronics
Disassembly and Reassembly
Œ
´
Ø
∏”’ Ô ˝
Ò
”
ˇ ¨
ˆ
Fig. 1-2 Top Parts Location-2
ΠFE HEAD
´ CYLINDER ASS’Y
ˇ ACE HEAD ASS’Y
¨ LEVER UNIT PINCH ASS’Y
ˆ LEVER #9 GUIDE ASS’Y
Ø LEVER TENSION ASS’Y
∏ BAND BRAKE ASS’Y
” DISK S REEL
’ LEVER S BRAKE ASS’Y
˝ GEAR IDLE
Ô LEVER IDLE
LEVER T BRAKE ASS’Y
Ò DISK T REEL
Disassembly and Reassembly
Samsung Electronics
1-3
1-1-2 Bottom View
Œ
´ˇ
¨
ˆ
Ø
∏
”
’
˝
Fig. 1-3 Bottom Parts Location
ΠGEAR JOINT 1
´ GEAR JOINT 2
ˇ BRACKET GEAR
¨ MOTOR CAPSTAN ASS’Y
ˆ LEVER T LOAD ASS’Y
Ø GEAR LOADING DRIVE
∏ LEVER S LOAD ASS’Y
” HOLDER CLUTCH ASS’Y
’ BELT PULLEY
˝ SLIDER CAM
1-4
Samsung Electronics
Disassembly and Reassembly
1-2-2 Lever FL Door Removal
1) Release the Hook ´ and Remove the Lever FL
Door Œ in the direction of arrow “C”.
"B"
"A"
´ LEVER FL DOOR
ˇ HOOK
1-2-1 Holder FL Cassette Ass’y Removal
1) Pull the Holder FL Cassette Ass'y Πto the eject
position.
2) Pull the Holder FL Cassette Ass'y Πas grasping
the Holder FL Cassette Ass'y Πand Lever FL
Cassette-R ´ in the same time to release hooking
from Main Base until the Boss [A] of Holder FL
Cassette Ass'y Πis taken out from the Rail [B].
3) Lift the Holder FL Cassette Ass'y Œ, in this time,
you have to grasp the Lever FL Cassette-R ´
Continuously until the Holder FL Cassette Ass'y
Πis taken out completely.
Note : Be sure to insert Lever FL Cassette-R ´ in the
direction of “A” to prevent separation and breakage
of the Lever FL Cassette-R ´ at disassembling and
reassembling.
ΠHOLDER FL
CASSETTEE ASS`Y
BOSS [A]
RAIL [B]
´ LEVER FL CASSETTEE -R
"A"
1-2 Main Deck
Fig. 1-5 Lever FL Door Removal
Fig. 1-4 Holder FL Cassette Ass’y Removal
Disassembly and Reassembly
Samsung Electronics
1-5
1-2-4 Lever FL Arm Ass’y Removal
1) Push the hole “A” in the direction of arrow “B”
use the pin.(about Dia. 2.5)
2) Pull out the Lever FL Arm Ass'y Πfrom the Boss
of Main Base.
3) Remove the Lever FL Arm Ass'y Πin the direction
of arrow “C”.
ΠGEAR FL CAM
GEAR WORM WHEEL
POST
TIMING POINT
Fig. 1-7 Gear FL Cam, Gear Worm
1-2-3 Slider FL Drive, Gear FL Cam Removal
1) Pull the Slider FL Drive Πto the front direction.
2) Remove the Slider FL Drive Πin the direction of
arrow. (Refer to Fig. 1-6)
3) Remove the Gear FL cam ´.
Note : When reinstalling be sure to reassemble Slider
FL drive Πafter you insert the Boss of Lever FL
ARM-R in Groove of Slider Fl drive Œ.
Assembly : Align the Gear FL Cam Πwith the Gear
worm wheel Post as shown drawing.
(Refer to Timing point)
ΠSLIDER FL DRIVE
´ GEAR FL CAM
Fig. 1-6 Slider FL Drive Removal
ΠLEVER FL ARM ASS`Y
"C"
"B"
PIN
HOLE "A"
Fig. 1-8 Lever FL Arm Ass’y Removal
1-6
Samsung Electronics
Disassembly and Reassembly
1-2-5 Gear Worm Wheel Removal
1) Remove the Gear Worm wheel Œ.
ΠGEAR WORM WHEEL
Fig. 1-9 Gear Worm Wheel Removal
1-2-6 Cable Flat Removal
1) Remove the Drum connecting part of Cable Flat Œ
from Connector Waffer ´.
2) Remove the Loading Motor connecting part of
Cable Flat Œ from Connector Waffer ˇ.
3) Rotate the Damper Capstan ¨ in the direction of
arrow “A” and remove it toward “B”.
4) Pull the Cable Flat Œ in the direction of arrow “C”
to remove.
ˇ CONNECTOR WAFER
¨ DAMPER
CAPSTAN
´ CONNECTOR WAFER
CYLINDER
CONNECTING PART
LOADING MOTOR
CONNECTING PART
ΠCABLE FLAT
"C"
"A"
"B"
Fig. 1-10 Cable Flat Removal
Loading...