Samsung SNC-L200 User Manual

Netcam(W)

SNC-L200(W)

User’s manual

Safety instructions and precautions are designed to protect users and prevent any property damage. Please read and observe these instructions thoroughly before using the Netcam.

AB68-000524B(01)

NETWORK CAMERA

SNC-L200

Netcam(W)_SNC-L200(W)

Important Safety Instructions

Netcam(W)_SNC-L200(W)

Safety Precautions

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is presentinside. It is dangerous to make any kind of contact with any inside part of this product.

This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. This device complies with part 15 of the FCCRules. Operation is subject to the following two conditions.

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including interference that may cause undesired operation.

Class B NOTE :

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can reaiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures :

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit defferent from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer ’s instructions.

RF Radiation Exposure Statement

This equipment complies with FCC RF Radiation Exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer ’sinstructions.

8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer,or sold with the apparatus. When a used, caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus. When a cart is used, use caution when moving the

cart/apparatus combination to avoid injury from tip-over.

14. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

NOTE :

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.? SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

2 3

Declaration of Conformity to R&TTE Directive 1999/5/EC

This equipment fulfils the R&TTE directive(Council Directive 1999/5/EC).

- European States qualified under wireless approvals:

EU Austria, Belgium, Denmark, Finland, France (with frequency

restrictions), Germany, Greece, Ireland, Italy, Luxembourg, The Netherlands, Portugal, Spain, Sweden, and the United Kingdom

Accept EU Iceland, Liechtenstein, Norway, and Switzerland

- European States with restrictions on use:

EU In France,the frequency range is restricted to 2446.5-2483.5 MHz for

devices above 10 mW transmitting power such as wireless.

Accept EU No Limitations at this time.

Netcam(W)_SNC-L200(W) Netcam(W)_SNC-L200(W)

4 5

Features

1/4" 320,000-pixel CMOS

Provides high-quality video of 320,000-pixels (pixel is a number of dots comprising an image)by adopting high-resolution CMOS.

Pan &Tilt

Moves the lens up and down and left and right, allowing shooting of every corner in every direction.

Preset

Sets the directions of the lens up to eight spots. You can return the lens to the stored position easily after movement.

Night Flash

You can monitor the environment at nighttime or in a dark room by using flash.

Passive Infrared (PIR)Sensor

Automatically detects and shoot any motion from intrusion, and sends it by E-mail. You can use this function when you leave the house or return from work.

Support for Communications Protocols

Provides support for TCP/IP, SMTP for E-mail transmission, and FTP protocols, and provides a variety of Internet-related communications protocols such as ARP, HTTP, Telnet, DHCP and PPPoE.

Power Pan &Tilt

When you select a desired spot by clicking, the camera lens moves the spot to the center of the screen. You can adjust movement over a screen more easily and accurately.

Home Position

The lens returns to the central position after you press the Home Button at the center of the Pan &Tilt Button, and resets the coordinates of the Pan &Title.

Pre-Alarm

When motion is detected over the screen, both the detected image and the image before motion detection is sent to the E-mail address pre-set by the user (You can set the number of before and after-alarm images sent from the menu).

Privacy Protection

You can press the Privacy Button of the Netcam(W) if you do not want to shoot videos. Then the lens rotates to uncovered range, and the screen turns black. If you press the button again, ‘Privacy Mode’ is displayed on the black screen.

PRIVACY

The Netcam can be installed in any place you want at domestic, business or industrial premises, and provides real-time security moving images over the Internet, allowing remote controlling for security and monitoring.

The NetcamW is a wireless network camera adopting wireless network technology, which allows users to access a security camera without LAN cable connection.

Netcam(W)_SNC-L200(W)

Before Using This Manual

Netcam(W)_SNC-L200(W)

Features

- Class A Devices (Class A:for business use, Class B : for domestic use)

- Before using this product, please read the safety instructions thoroughly and carefully.

- Check the trouble shooting procedures when a problem occurs.

- You can refer to the index for better understanding of technical terms.

Currently, SNC-L200 (W) is available in the following areas within Europe:

- UK / France / Germany / Spain/Italy / The Netherlands / Belgium / Norway / Denmark / Sweden / Russia / Poland / Czech / Hungary

Icons Titles Functions

Warning Functions of this camera may not work or settings can be changed.

Note

Refer to the page containing hints or help on performance of the product.

Icons used in this manual

How to Use the User’ s manual

Web-browser Monitoring

You can view video of the Netcam(W) over an Internet Web browser, so you can view video not only in the local network environment but also over an external Internet network.

Auto Local IP Set

Provides easy-to-use installation functions for users who are unfamiliar

with settings of an environment.

Universal Plug and Play (UPnP)

When the Netcam(W) is connected with an IP router or a wireless router capable of UPnP functions, this camera automatically performs the port forwarding that enables access from external Internet. You can easily access the Netcam(W) by using the “Netcam(W)” icon displayed in “My Computer Environment.”

802.11b Wireless Network (NetcamW Only)

You can use this camera over an IEEE 802.11b wireless network without connecting the NetcamW to a LAN cable.

Access to Netcam(W) via a cell phone

You can view still images of Netcam(W) by accessing the Internet via a cell phone.

UPnP

Netcam(W)_SNC-L200(W)Netcam(W)_SNC-L200(W)

Contents

Safety Precautions ..............................10

Title of Each Component ....................12

- List of Components ....................................12

- Passive Infrared (PIR)Sensor ....................14

- Flash ..........................................................14

- Privacy........................................................15

- Reset ..........................................................15

Internet Connection ............................17

Power Connection................................18

Opening the Back Cover/Arranging Cable

....19

Installing the Camera ..........................20

- Installing the camera on the wall

(concrete or cemented wall)

................20

Installing the camera in Standing position

....21

- Installing the camera on a Tripod

......21

Installing the IP Router of Wireless Router

....23

Installing the IP Router of Wireless Router

....23

- Setting the Port Forwarding........................23

Installing the SNC Installer..................24

Searching the Connected Netcam(W)

........26

Setting the Network..............................28

- Auto Setting the Network............................28

- Manually Setting the Network ....................30

- Port Forwarding..........................................34

Access to the Netcam(W) Website ....38

- Access from a Local Network PC ..............38

- Access from External Internet ....................39

Installing the ActiveX Control ............41

- For Windows 2000/Windows XP ................41

- For Windows XP Service Pack 2................42

- Manually Installing the Activex Control ......43

Using the Smart Viewer ......................44

- Power Pan &Tilt… ......................................45

- Preset ........................................................46

- Passive Infrared (PIR) ................................47

- Flash ..........................................................47

- Record Moving Images ..............................48

- Change the Record Route..........................48

Using the Simple Player ......................49

- Play Back Recorded Files ..........................49

- Stop Recorded Files ..................................50

- Capture Playback Images ..........................50

- Print Playback Images................................51

Setting the Smart Viewer ....................53

System Configuration..........................54

Network Configuration ........................59

Utilities ..................................................66

Access to Netcam(W) via a cell phone (USA Only)

....72

Installing the MultiViewer Program ....75

Registering the Netcam(W) ................76

- Registering the Netcam(W) ........................76

Connecting the Netcam(W) ................78

Using the MultiViewer ..........................80

- MultiViewer Screen ....................................80

- View Multi Channel ....................................82

- Sequence View ..........................................84

- Recording Video..........................................85

- Recording Motion ........................................86

- Capturing Video ..........................................88

- Printing Video..............................................88

- Screen Display ............................................89

- Running the SNC Installer ..........................89

Playing Back the MultiViewer ..............90

- Record File Playback ..................................92

- Event Log Information ................................93

Setting the MultiViewer ........................94

- Setting the Viewer Environment..................95

- Setting the Scheduled Recording................96

- Selecting Logo ............................................97

Product Specifications ........................98

Preparations Single Use

Multi Use

Connection

Others

Netcam(W)_SNC-L200(W)

Safety Precautions

Strict compliance with the safety instructions is required for protection and ensured safety of users and prevention of property damage.

Failing to comply with the instructions may result in injury or even fatality.

Warning

Power

Installation

Storage&Maintenance

Do not disassemble,repair and reassemble this product. It may result in malfunctioning, causing a fire, electric shock or injury.

Do not install the camera in a wet, dusty or smoky place. It may cause a fire or electric shock.

Do not install the camera under direct sunlight or near a heat-generating system. It may cause a fire.

Use the designated power adapter provided by the manufacturer (DC8.4V/1A) Using other power adapters may cause a fire, electric shock or malfunctioning.

Pull out the power plug during a lightening or storm. It may cause a fire.

Insert the power plug firmly to secure the connection. Insecure connection may cause a fire.

Do not use more than one plug at the same time. It may generate heat or cause a fire if the connection is insecure.

Do not bend power cords and do not place heavy objects on power cords. It may cause a fire.

You must not hold the power plug with wet hands. It may cause an electric shock.

Failing to comply with the instructions may results in injury or even fatality.

Warning

Storage&Maintenance

Do not place this product near a vase, a flowerpot, a cup, cosmetics, medicine or water. It may cause an electric shock.

Do not use this product when it generates smoke or smell. Turn off power and pull out the plug immediately before calling the service center. If you continue using the product, it may cause a fire or electric shock.

Do not spray water directly onto parts of this product when cleaning. Use a dry towel instead. It may cause a fire or electric shock. Do not use chemicals or detergents that can deteriorate the surface of the product.

Failing to comply with the instructions may results in a loss injury or even fatality.

Warning

Installation

Fix this product firmly so that it cannot drop. Avoid installing the product in closed area. It may cause damage to the product.

Do not install the product in a hot (35 0 C or higher)or cold (5 0 C or lower)place. It may cause an electric shock.

Place this product out of children ’s reach. Throwing down the product may cause injury.

Storage&Maintenance

Do not move the product during operation. Turn off power before moving or reinstalling the product.

Do not drop an object or impose too much force on the product. It may cause malfunctioning.

Avoid installation in place with too much vibration or magnetic force. It may cause malfunctioning.

Netcam(W)_SNC-L200(W)

Title of Each Component

Front

Back

NETWORK CAMERA

SNC-L200

Camera

Lens

Passive Infrared

(PIR)Sensor

Power LED

SNC-L200W :

- LED turns red when power is connected.

- LED turns amber when the system is boosted.

- LED blinks in red and amber in turn when Privacy functions are turned on.

SNC-L200 :

- It turns on when it is connected to the power source.

Network LED

SNC-L200W :

- LED turns green when the network is connected.

- LED turns amber when the network is being changed.

SNC-L200 :

It turns on when it is connected to the networks.

It blinks when it receives or transfers data.

Flash

Privacy Button

Power Connector

LAN Connector

Reset Button

Bottom Side

Back Cover

Wiring Home

Fix Home

Tripod Fix Home

Fix Home

List of Components

You can download the latest version of software from the Samsung Electronics Web site (http://www.samsung.com).

Netcam(W)

User ’s Manual

(Warranty Included)

Installation

Power Adapter (DC

8.4V/1A)(DC8.4V/1A)

Power Cord

EMI suppression

ferrite core

for Power Cable

EMI suppression

ferrite core

for LAN Cable

Screws/Fix labels/

Anchor (16X3)2

Netcam(W)_SNC-L200(W)

Title of Each Component

Passive Infrared (PIR)Sensor

Detects and records motion of a human or an animal by using an infrared ray.

- Selects perform or cancel by using the PIR Sensor Button of Smart/Multi Viewer.

- Flash can be turned on in link with the PIR Sensor.

Distance and Range

Distance of Detection : Up to 3m

Range of detection (up and down) : Around 85°

Range of detection (left and right) : Around 40°

Distance and Range

Distance of Light Emitting : Up to 3m

Range of detection (up and down) : Around 67°

Range of detection (left and right) : Around 67°

Flash

You can monitor the environment even in a dark room by using flash.

- Turns on the flash by using the Flash button of the Smart/Multi Viewer.

- Flash can be turned on in link with the PIR Sensor.

- Flash is turned on for 5 seconds and off for 30 seconds. Even i f you click the Flash Button in 30 seconds, flash is not turned on.

- Flash is also turned on for 5 seconds and off for 30 seconds when using the PIR Sensor.

Range of detection left and right Range of detection up and down

Range of light emitting left and right

Range of light emitting up and down

Privacy

Turns the lens out of the performance range to prevent shooting for privacy.

Press the Privacy Button.

- Every time you press the button, [the lens moves out of the performance range ‘Privacy Mode’ is displayed and video is not transmitted restore to the previous state ] process is repeated.

Reset

When the product is not in normal conditions, you can set the values to factory default.

Press the Reset Button on the back for more than 5

seconds.

- Refer to the title of each component for the location of the Reset Button (page 12).

- All the values are restored to factory default settings, and the system is rebooted. Use the product after some 2 minutes.

The left and right range of detection may change if motion is fast. Avoid exposing this product to direct sunlight, air conditioner or heater, high or cold temperature, humidity, oil, smoke and glass when installing the product. The Sensor may malfunction.

Warning

Do not use this function unless necessary. Stored values such as the network settings, registered users, the title of the Netcam(W), firmware upgrades are all switched to factory default settings.

Warning

Netcam(W)_SNC-L200(W)

Internet Connection

You can remotely monitor moving images in real time by connecting the camera to the Internet and setting up the network environment.

Connection

Please read power, network connection and installation instructions carefully before connecting to the Internet.

Connect the LAN connector of the Netcam ((W)to the LAN connector of the IP Router (Router or Wireless Router).

Connect the LAN connector of the IP Router to the LAN connector of the PC.

Connect the WAN connector of the IP Router to the Internet..

IP Router (Router or Wireless Router)

External PC

Back of Main Body

Direct Cable

It is recommended to use the EMI suppession ferrite core to prevent the influence of EMI.

Wrap the EMI suppession ferrite core with the LAN cable three times as shown in the figure.

In similarity, wrap the EMI suppession ferrite core with the power adapter cord three times.

How to Use the EMI suppession ferrite core

Do not extend the direct cable to more than 100m.

Warning

Netcam(W)_SNC-L200(W) Netcam(W)_SNC-L200(W)

18 19

Opening the Back Cover/Arranging Cable

Learn how to open the back cover and arrange the cable.

Power Connection

Connect power by using the power adapter and cord provided as accessories of this product.

”»ˆ… ‚Ø

Connect the power adapter to the power connector of the Netcam(W).

Connect the jack of the power cord to the power adapter.

Insert the power plug to the wall outlet.

- When power is connected,power LED (red)is turned on,and the lens automatically moves after 2 minutes.

CAUTION

Use only power supply, Manufacturer : Dongyang E&P, Model : AA-E8 (SNC-L200)

Push the back over with two hands to open it.

Connect the power cable to the power connector and the LAN connector.

Close the cover after aligning the cable with the wiring groove.

Arrange the cable.

- Arrange the cable in direction B when installing the camera on the wall.

Arrange the cable in direction A when installing the camera in Standing position.

➞➞

Top Cover

Use the power adapter provided by the manufacturer. (DC8.4V/1A)

Note

Power LED

Back of Main Body

Power Adapter

1 1

➞➞

Netcam(W)_SNC-L200(W)

Installing the Camera

You can install the camera on the wall, in standing position or on the tripod after deciding the place and height of installation.

Installing the camera on the wall (concrete or cemented wall)

Insert two plastic plugs to the holes.

Insert two screws by using a driver.

Arrange the power cable and the LAN cable in direction A (see page 17).

Hang the Netcam(W) on the screws,and push it down to fix.

Attach the fixing label on the wall. Make two holes by using an electric drill.

- Each hole must be more than 5mm in diameter and 35mm in depth. Keep 35mm distance between holes.

Adjust to

this position

Installing the camera in Standing position

Arrange the power cable and the LAN cable in direction B (see page 17).

Place the camera on a proper place such as a cabinet.

Installing the camera on a Tripod

Arrange the power cable and the LAN cable in direction A (see page 17).

Align the tripod fix groove to the projecting part of the tripod, and rotate to insert it.

- Check whether the wall is firm enough to support the weight of the Netcam(W) when installing the camera on the wall.

- The camera may fall. Be careful not to be injured.

- This product is intended for indoor use. Avoid exposing the product to rain, snow or moisture.

- When using a separate stand, check whether it fits the groove of the tripod. They may be loosely connected and separated.

Follow the step 1,4,5 and 6 when installing the camera on hard board or on the wooden wall.

Note

Warning

1 2

3 4

35mm

Netcam(W)_SNC-L200(W)

Setting the Router or Wireless Router

If you want to connect the PC and the Netcam(W) with a single line of the Internet, you must have an IP router. You are also required to set the IP router for normal operations.

Single Use

- Video transmission may slow down depending on PC performance or network conditions.

- Do not enter the IP address and Mc address used for illustration in this manual.

Recommended System Specifications

- Computer : Pentium 4/1.5GHz or higher (Pentium 4/1GHz or higher at minimum)

- Operating System : Windows 2000/XP

- Ram : Memory : 256MB or higher

- Video : Memory : 128MB or higher

- Resolution : 1024 X 768 or higher

- Web Browser : Internet Explorer 6.0 or higher

Installing the IP Router of Wireless Router

Read the user ’s manual before installing the IP router.

- Set the IP address on the IP router.

- The IP address is used to set the network of the Netcam(W).Keep a record of the address for later use.

- The Subnet Mask or the Gateway status of the IP router connection is used to set the network of the Netcam(W). Keep a record of the status for later use.

- A wireless router is required for wireless communication of the NetcamW.

- The wireless information (SSID,WEP etc.)of the wireless router settings is used to set the wireless connection of the NetcamW. Keep a record of the information for later use.

Setting the Port Forwarding

The port forwarding is automatically set when the IP router

(router or wireless router)of the SNC Installer of the Netcam(W) supports UPnP.

When the router does not support UPnP, you must set the port number allocated

for the Netcam(W) by the IP router. Enter a value between 1 to 65535.

You must not use the following port numbers.

FTP : 21 Telnet : 23 SMTP (E-mail:) : 25

DNS : 53 POP3 : 110 HTTPS : 443

ICQ : 4000 IRC : 6661~6667

It is recommended to set the number to higher than 10,000 since you can prevent collision with port numbers of other Internet service or programs by avoiding commonly used numbers.

IP routers that support UPnP are listed below.

- Netgear WGR614 v5, WGR614 v6

- D-Link DI-624, DI-624+, DI-624+A

- Zio WLB5054IP

Netcam(W)_SNC-L200(W)

Installing the SNC Installer

Search and set up the Netcam(W) connected to the hub or the IP router.

Insert the installation CD into the CD-ROM driver of the PC.

Click the “Install ”Button.

Double click “SNC Installer.exe.”

Click the “Next ”Button.

Click the “Finish ”Button.

- The “Move to ”Icon is created on the background screen when the installation is completed.

Click

➞

SNC

Installer

Netcam(W)_SNC-L200(W)

Searching the Connected Netcam(W)

Used to search an IP router (router or wireless router)connected with the Netcam(W) or a Netcam(W) directly connected with the PC.

Run the program by double-clicking the SNC Installer icon. Or you can click [Start ]-[All Programs ]-[SNC Installer ]-[SNC Installer ].

- If a warning screen appears, click the ‘block clear’ button (Windows XP Service Pack2).

Press the ‘OK ’Button.

When the SNC Installer is run, the following window appears and all the Netcam(W) over the single network are searched automatically.

- Press the Cancel Button on the [Searching ….] window to cancel the search during process.

1. Server Name: The name of the Netcam(W) set by the manager

2. Model: The model name of the Netcam(W)

3. IP Type: Displays the current status of network among Static,DHCP and PPPoE.

4. IP Address: The IP address of the Netcam(W)

5. HTTP Port: The port number used to access the Netcam(W) connected over a local network.

6. Mac Address: The hardware address of the Netcam(W) shown on the back of the label.

7. Ext Port: The port number that allows access to the Netcam(W) from the external Internet.

8. Status : “Success(W)”appears when the network settings are correct,and “Auto Fail ”appears when the

settings are not authorized during the installation process.

9. Search Button: Searches the Netcam(W) currently connected over the network.

10. Clear Button: Deletes the list of the Netcam(W) s from the SNC Installer List.

11. Manual Set Button: The user enters the network settings of the Netcam(W).

12. Auto Local Set Button: The SNC Installer automatically sets the network settings of the Netcam(W).

13. Internet Set (UPnP)Button: Port-forward to enable access to the Netcam(W) from the external

Internet.

14. Close Button: Closes the SNC Installer window.

15. URL via internet: The URL address used for access from the external Internet.

SNC Installer Screen

The search function of the SNC Installer is enabled when the camera is connected with the PC via an IP router or directly with the PCover a single network.

Note

Click

91011

13 14

234 5 67

Netcam(W)_SNC-L200(W)

Setting the Network

You can set a variety of network settings such as IP address and UPnP by using the SNC Installer program. You can choose between <Auto Local Set>and <Manual Set>.

Click the Auto Local Set Button on the bottom of the SNC Installer screen.

Enter a proper value for each item.

Apply the set values to the Netcam(W), and save the values by entering the Root password and clicking the Set Button in the Save Configuration Option.

- Click the ‘Cancel’ Button to cancel the set value.

Click the “Yes ”Button.

- The following screen appears for about 2 minutes.

Auto Setting the Network

The SNC Installer searches and automatically allocates available IP and Subnet Masks over the user network by using the Auto Local Set.

Server Name: Set the name of the Netcam(W).You can enter up to 20 letters

(alphabet and Roman Numerals). You cannot use special characters such as #, ’ , ” and:.

IP Address: Automatically enter the IP available in the user network environment.

Netmask: Automatically enter the Subnet Mask of the IP router (router or wireless router).

Wireless Enable/Wireless Disable(SNC-L200W Only): Choose the “Wireless Enable ”when using wireless

connection of the NetcamW. Choose the “Wireless Disabled ”when not using wireless connection.

AP Information (SNC-L200W Only) :ESSID: Enter the (E)SSID used by the wireless router to be connected. Press the “Scan AP ”Button next to

the item, and the list of (E)SSIDs the wireless routers presently available from the NetcamW appears. AUTH MODE: Choose the AUTH Mode of the wireless router to be connected between the Open System and the Shared Key.

WEP: Select “WEP ”when the wireless router to be connected uses the “WEP ”wireless security settings. Mode: Select the type of the WEP Key set for the wireless router to be connected. KEY: Enter the value of the WEP Key set for the wireless router to be connected.

Root password: The password is defaulted to “root”.

Enter a new password if the current one is changed.

1 2

3 4

Auto Local Set Screen

Click

When the Auto Local Set is completed, the Internet Set (UPnP)window appears as follows.

- Click “Yes ”to set up connection over the Internet (refer to pages 38 to 40 for setup).

- Click “No ”to not set up connection over the Internet.

“IP collision” may occur between Netcam(W) and the PC if a firewall is installed over a single network.

Exclude the IP of the PC with the firewall if collision occurs.

Warning

+ 35 hidden pages