Samsung SCV-2080 Installation

SCV-2080 Series Quick Install Guide

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION- This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the manufacturer

WARNING -To prevent electric shock and risk of fire hazards:

ý Do NOT use other than specified power source. ý Do NOT expose this appliance to rain or moisture.

could void the user’s authority to operate the equipment.

This installation should be made by a qualified service person and should conform to all local codes.

1. INSTALLATION

Notes

• The installation should be done by qualified service personnel or sysytem installers.

• If the ceiling material is not strong enough to hold the installation screws, the camera may fall off. Reinforce the ceiling as needed.

• If you don't install the main body on he mounting bracket, the camera may not be waterproof according to install location.

Using the L-wrench provided, loosen 3 screws by turning them counterclockwise and separate the dome cover.

2) Lift up the inner cover while gently pressing both ends to separate it from the unit.

Loosen 3 screws by turning them counterclockwise, press both left and right lock releases inwards (in arrow direction) to unlock the stopper, and then separate the camera from the case.

Dome Cover

Inner cover

Main Body (Camera)

Case

Installing the camera on a ceiling or wall

1) Affix the mounting template(supplied) to the mounting surface.

Drill holes (diameter 5mm, more than 35mm deep) on the ceiling by matching to the holes on the case bed, and insert plastic anchors (HUD 5) fully into the holes. Fix the case bed on the ceiling by using Tapping Screws (TH M4xL30). (4 places)

3) Connect power and video cables and arrange cable running not to damage or squeeze them, and assemble the camera unit in the reverse way.

Pass the power and BNC cable through the hole you want to pass them when mounting the main body on the mounting bracket.

5) Secure the camera on its mounting bracket with the four screws.

Ø5 tapping screw x 4 (supplied)

M4 machine screw x 3

Installing the camera on a ceiling or wall with pipeline

1) Secure the mounting bracket on the place you want to mount it after combining the mounting bracket with the pipeline.

2) Connect power input and video output cables with the each cable from pipeline.

3) Secure the main body on mounting bracket.

Hole for 3/4° pipe (JIS B 0202-1966)

Ø5 tapping screw x 4 (supplied)

M4 machine screw x 3

431

Reinstall the dome cover to the main body

1) Adjust the lens in a desired direction.

Case

Main Body (Camera)

2. ADJUSTING THE MONITORING DIRECTION OF THE CAMERA

Panning

3. OPTIONAL ACCESSORIES FOR INSTALLATION

For your easier installation, you can purchase appropriate optional accessories.

1) WALL MOUNT ADAPTOR(SCX-300WM)/HANGING MOUNT(SCX-300HM) This adaptor is used when installing the dome camera onto a wall.

MEMO

Secure the inner cover to the main unit.

Assemble the Dome Cover. For waterproof purpose, fix and secure the bolt using L-wrench provided.

Inner cover

Dome Cover

Tilting

Lens rotation

You can adjust the camera direction only when the camera is fixed on the ceiling.

0˚

60˚ ~ 80˚

Then, turning the camera to the left or right is referred to as "Panning", while moving the camera angle up or down is "Tilting". For panning, the panning limit is 220° for the clockwise, and 135° for the counter-clockwise, a total of 355° enabled; further rotation is prevented by the stopper.

•

Adjust the panning angle so that the camera settles in the right horizontal position. You can adjust the panning up to 135° in each one direction, and 220° in the other direction, a total of 355°.

• Adjust the tilting angle so that the camera settles in the right vertical position. You can adjust the tilting between 0° and 90°.

•

The total rotation range is 355°. You can make adjustment in one direction up to 125°, and 230° in the other direction.

2) Methods of adjustment

• The case of wall installation

➊

After mounting the camera on the wall, adjust the panning angle so that the camera faces a

desired direction when tilting.

➋

Adjust the Rotate position to fit the video to the screen borders.

➌

Then, adjust the tilting angle so that the camera faces the monitoring direction.

• The case of ceiling installation

➊

After mounting the camera on the ceiling, adjust the panning angle according to the

monitoring direction. You should adjust the panning angle lest that the video be displayed upside down on the monitor.

➋

Adjust the Rotate position to fit the video to the screen borders.

➌

Then, adjust the tilting angle so that the camera faces the monitoring direction.

Notes

• For smoother Rotate adjustment, set the Tilt position between 60˚ ~ 80˚.

2) CEILING MOUNT ADAPTOR(SCX-300CM)/ HANGING MOUNT(SCX-300HM) This adaptor is used when installing the dome camera on a concrete ceiling.

3) POLE MOUNT ADAPTOR(SCX-300PM) This is an adaptor for WALL MOUNT ADAPTOR (SCX-300WM) installation on a pole whose diameter is bigger than 80mm.

4) CORNER MOUNT ADAPTOR (SCX-300KM) This is an adaptor for WALL MOUNT ADAPTOR (SCX-300WM) installation on the corner of wall joint.

CONNECTION

Output of the adaptor should be either one of AC 24 V, 1.5 A or DC 12 V, 1.0 A. Note

that using DC 12 V may cause lower heater temperature.

• Connecting to Power

---- Power Input Terminal

P/No. : Z6806-1323-01A

8765