Samsung VP-L10, VP-L150, SCL100, SCL150 Service Manual
8mm CAMCORDER
VP-L100/VP-L150
SCL100/SCL150
SERVICE
1. Precautions
2. Reference Information
3. Product Specifications and
Comparison Chart
4. Disassembly and Reassembly
5. Alignment and Adjustment
6. Exploded View and Parts List
7. Electrical Parts List
8. Block Diagrams
9. PCB Diagrams
10. Wiring Diagram
11. Schematic Diagrams
Manual
8mm CAMCORDER
CONTENTS
For mechanical disassembly and adjustment, refer to the “Mechanical Manual”
(DE-6 AD68-30200A).
A
Samsung Electronics 1-1
1. Precautions
1. Be sure that all of the built-in protective devices are
replaced. Restore any missing protective shields.
2. When reinstalling the chassis and its assemblies, be
sure to restore all protective devices, including :
control knobs and compartment covers.
3. Make sure that there are no cabinet openings
through which people--particularly children
--might insert fingers and contact dangerous
voltages. Such openings include the spacing
between the picture tube and the cabinet mask,
excessively wide cabinet ventilation slots, and
improperly fitted back covers.
If the measured resistance is less than 1.0 megohm
or greater than 5.2 megohms, an abnormality exists
that must be corrected before the unit is returned
to the customer.
4. Leakage Current Hot Check (See Fig. 1) :
Warning : Do not use an isolation transformer
during this test. Use a leakage current tester or a
metering system that complies with American
National Standards Institute (ANSI C101.1,
Leakage Current for Appliances), and Underwriters
Laboratories (UL Publication UL1410, 59.7).
5. With the unit completely reassembled, plug the AC
line cord directly the power outlet. With the unitÕs
AC switch first in the ON position and then OFF,
measure the current between a known earth
ground (metal water pipe, conduit, etc.) and all
exposed metal parts, including : antennas, handle
brackets, metal cabinets, screwheads and control
shafts. The current measured should not exceed
0.5 milliamp. Reverse the power-plug prongs in the
AC outlet and repeat the test.
6. X-ray Limits :
The picture tube is designed to prohibit X-ray
emissions. To ensure continued X-ray protection,
replace the picture tube only with one that is the
same type as the original.
Fig. 1 AC Leakage Test
7. Antenna Cold Check :
With the unitÕs AC plug disconnected from the
AC source, connect an electrical jumper across the
two AC prongs. Connect one lead of the ohmmeter
to an AC prong.
Connect the other lead to the coaxial connector.
8. High Voltage Limit :
High voltage must be measured each time
servicing is done on the B+, horizontal deflection
or high voltage circuits.
Heed the high voltage limits. These include the
X-ray protection Specifications Label, and the
Product Safety and X-ray Warning Note on the
service data schematic.
9. Some semiconductor (Òsolid stateÓ) devices are
easily damaged by static electricity.
Such components are called Electrostatically
Sensitive Devices (ESDs); examples include
integrated circuits and some field-effect transistors.
The following techniques will reduce the
occurrence of component damage caused by static
electricity.
10. Immediately before handling any semiconductor
components or assemblies, drain the electrostatic
charge from your body by touching a known
earth ground. Alternatively, wear a discharging
Wrist-strap device. (Be sure to remove it prior to
applying power--this is an electric shock
precaution.)
Device
Under
Test
(Reading should
not be above
0.5mA)
Leakage
Currant
Tester
Earth
Ground
Test all
exposed metal
surfaces
Also test with
plug reversed
(using AC adapter
plug as required)
2-Wire Cord
Precautions
1-2 Samsung Electronics
11. High voltage is maintained within specified limits
by close-tolerance, safety-related components and
adjustments. If the high voltage exceeds the
specified limits, check each of the special
components.
12. Design Alteration Warning :
Never alter or add to the mechanical or electrical
design of this unit. Example : Do not add
auxiliary audio or video connectors. Such
alterations might create a safety hazard. Also, any
design changes or additions will void the
manufacturerÕs warranty.
13. Hot Chassis Warning :
Some TV receiver chassis are electrically
connected directly to one conductor of the AC
power cord. If an isolation transformer is not
used, these units may be safely serviced only if
the AC power plug is inserted so that the chassis
is connected to the ground side of the AC source.
To confirm that the AC power plug is inserted
correctly, do the following : Using an AC
voltmeter, measure the voltage between the
chassis and a known earth ground. If the reading
is greater than 1.0V, remove the AC power plug,
reverse its polarity and reinsert. Re-measure the
voltage between the chassis and ground.
14. Some TV chassis are designed to operate with 85
volts AC between chassis and ground, regardless
of the AC plug polarity. These units can be safely
serviced only if an isolation transformer inserted
between the receiver and the power source.
15. Never defeat any of the B+ voltage interlocks.
Do not apply AC power to the unit (or any of its
assemblies) unless all solid-state heat sinks are
correctly installed.
16. Always connect a test instrumentÕs ground lead to
the instrument chassis ground before connecting
the positive lead; always remove the instrumentÕs
ground lead last.
17. Observe the original lead dress, especially near
the following areas : Antenna wiring, sharp
edges, and especially the AC and high voltage
power supplies. Always inspect for pinched, outof-place, or frayed wiring. Do not change the
spacing between components and the printed
circuit board. Check the AC power cord for
damage. Make sure that leads and components
do not touch thermally hot parts.
18. Picture Tube Implosion Warning :
The picture tube in this receiver employs
Òintegral implosionÓ protection. To ensure
continued implosion protection, make sure that
the replacement picture tube is the same as the
original.
19. Do not remove, install or handle the picture tube
without first putting on shatterproof goggles
equipped with side shields. Never handle the
picture tube by its neck. Some Òin-lineÓ picture
tubes are equipped with a permanently attached
deflection yoke; do not try to remove such
Òpermanently attachedÓ yokes from the picture
tube.
20. Product Safety Notice :
Some electrical and mechanical parts have special
safety-related characteristics which might not be
obvious from visual inspection. These safety
features and the protection they give might be
lost if the replacement component differs from the
original--even if the replacement is rated for
higher voltage, wattage, etc.
Components that are critical for safety are
indicated in the circuit diagram by shading,
( or ).
Use replacement components that have the same
ratings, especially for flame resistance and
dielectric strength specifications. A replacement
part that does not have the same safety
characteristics as the original might create shock,
fire or other hazards.
2. Reference Information
2-1 IC Blocks
Reference Information
Samsung Electronics 2-1
2-1-1 IC501 (KA8322)
Reference Information
2-2 Samsung Electronics
2-1-2 IC601 (CXP87240A)
Reference Information
Samsung Electronics 2-3
2-1-3 ICP01 (KS7213)
Reference Information
2-4 Samsung Electronics
2-1-4 ICP03 (TDA8786A)
Reference Information
Samsung Electronics 2-5
2-1-5 ICP04 (KS7306B)
Reference Information
2-6 Samsung Electronics
2-1-6 ICP05 (UPD784038 / AF MICOM)
Reference Information
Samsung Electronics 2-7
2-1-7 ICZ01 (KS7314 / D.ZOOM)
Reference Information
2-8 Samsung Electronics
MEMO
Samsung Electronics 3-1
3. Product Specifications and Comparison Chart
3-1 Product Specifications (SCL100 / SCL150)
Design and specifications are subject to change without notice.
Operation
Description
SYSTEM
LCD Three-inch color TFT Liquid Crystal Display (LCD) screen
Recording systems Video : Two rotary heads, helical FM scanning / Audio : FM stereo system
Video signal NTSC color, EIA standard
Cassette format 8 mm
Tape speed SP mode (Standard Play) : approx. 14.345 mm/sec
Recording/Playback time SP mode (Standard Play) : 1 hour (P6-60)
Fast-forward/rewind time Approx. 3 minute 30 seconds (P6-60)
Image device CCD (Charge Coupled Device)
Viewfinder Black and White electronic viewfinder
Lens Combined 16X power zoom and (32X:SCL100, 64X:SCL150) digital zoom lens,
f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm.
Automatic focus system Inner
Color temperature Auto
Aperture correction Automatic with back light adjustment
OUTPUT CONNECTORS
Video output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative
Audio output Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms
GENERAL
Power requirement AC power adapter (7.2V) ; battery pack (6.0V)
Power consumption 6.5W (Camera Recording, LCD on)
Tripod attachment thread Attachment screw less than 6mm long
Microphone Electric condensor microphone, omni-directional, monaural type
Temperature range Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F)
Dimensions/weight Approx. 213 X 116 X 107 mm (L X H X W); Approx. 1000 g
Excluding battery pack and cassette.
Product Specifications
3-2 Samsung Electronics
3-2 Product Specifications (VP-L100 / VP-L150)
Design and specifications are subject to change without notice.
Operation
Description
SYSTEM
LCD Three-inch colour TFT Liquid Crystal Display (LCD) screen
Recording systems Video : Two rotary heads, helical FM scanning / Audio : FM stereo system
Video signal PAL colour, CCIR standard
Cassette format 8 mm
Tape speed SP mode (Standard Play) : approx. 20.051 mm/sec
Recording/Playback time SP mode (Standard Play) : 1 hour (P5-60)
Fast-forward/rewind time Approx. 4 minute (P5-60)
Image device CCD (Charge Coupled Device)
Viewfinder Black and White electronic viewfinder
Lens Combined 16X power zoom and 32X(VP-L150) digital zoom lens,
f=3.9 ~ 62.4mm, F1.4 Auto wide macro, Filter diameter 46mm.
Automatic focus system Inner
Colour temperature Auto
Aperture correction Automatic with back light adjustment
OUTPUT CONNECTORS
Video output Mini jack, 1Vp-p, 75 ohms, unbalanced, SYNC negative
Audio output Mini jack, 7.5dBs for an output impedance of less than 2.2 Kohms
GENERAL
Power requirement AC power adapter (7.2V) ; battery pack (6.0V)
Power consumption 6.5W (Camera Recording, LCD on)
Tripod attachment thread Attachment screw less than 6mm long
Microphone Electric condensor microphone, omni-directional, monaural type
Temperature range Operating : 0°C to 40°C (32°F to 104°F); storage : -20°C to 60°C (-4°F to 140°F)
Dimensions/weight Approx. 213 X 116 X 107 mm (L X H X W); Approx. 1000 g
Excluding battery pack and cassette.
Product Specifications
Samsung Electronics 3-3
3-3 Comparison Chart
VIEWFINDER EVF EVF EVF EVF
D.ZOOM X16 X32 D.ZOOM X32 D.ZOOM X64 D.ZOOM
VIDEO NORMAL NORMAL NORMAL NORMAL
STEREO X X X X
EIS X O X O
LCD 3 inch 3 inch 3 inch 3 inch
MODEL
FUNCTION
VP-L100 VP-L150 SCL100 SCL150
Product Specifications
3-4 Samsung Electronics
MEMO
Samsung Electronics 4-1
4. Disassembly and Reassembly
4-1 Cabinet and PCB
4-1-1 Ass’y Cover-Housing removal
ΠAPPLY POWER AND EJECT THE COVER HOUSING.
´ REMOVE 2 SCREWS.
ˇ REMOVE THE ASS'Y COVER-HOUSING IN
THE DIRECTION OF ARROW.
Fig. 4-1 Ass’y Cover-Housing removal
Disassembly and Reassembly
4-2 Samsung Electronics
4-1-2 Ass’y Case-Top removal
"B"
2 LOCKING TABS
PRECISION SCREW DRIVER
< DETAIL "A" >
< DETAIL "B" >
ΠREMOVE THE ASS'Y-CASE-TOP BY GENTLY RELEASING 2 LOCKING TABS
WITH A PRECISION SCREW DRIVER. (SEE DETAIL "A")
• NOTE : CLOSE THE HOUSING ASS'Y AFTER DISASSEMBLING.
• REASSEMBLY : PUT THE 7 TABS INTO THE SLOT WHILE
SLIDING IT AS SHOWN IN DETAIL "B".
Fig. 4-2 Ass’y Case-Top removal
Disassembly and Reassembly
Samsung Electronics 4-3
4-1-3 Ass’y Front removal
ΠREMOVE 2 SCREWS.
´ REMOVE 2 SCREWS.
¨ REMOVE THE ASS'Y-FRONT IN THE DIRECTION OF ARROW.
ˆ DISCONNECT 2 CONNECTORS FROM THE
CN891,CN893 OF AUDIO PCB.
ˇ REMOVE 1 SCREW.
Fig. 4-3 Ass’y Front removal
Disassembly and Reassembly
4-4 Samsung Electronics
4-1-4 Ass’y Case-Right removal
¨ REMOVE THE ASS'Y CASE-RIGHT IN THE DIRECTION OF ARROW "B".
ˇ SLIDE THE ZOOM SWITCH IN
THE DIRECTION OF ARROW "A".
ΠREMOVE 1 SCREW.
´ REMOVE 2 SCREWS.
Fig. 4-4 Ass’y Case-Rignt removal
Disassembly and Reassembly
Samsung Electronics 4-5
4-1-5 Ass’y Case-Left removal
¨ REMOVE 2 SCREWS.
ˆ REMOVE THE ASS'Y CASE-LEFT IN THE DIRECTION OF ARROW.
∏ DISCONNECT THE CONNECTER FROM THE CN502 OF MAIN PCB.
ˇ REMOVE 1 SCREW.
´ REMOVE 3 SCREWS.
ΠREMOVE 1 SCREW.
Fig. 4-5 Ass’y Case-Left removal
Disassembly and Reassembly
4-6 Samsung Electronics
4-1-6 Ass’y Case-Battery removal
´ DISCONNECT THE CN961 OF THE REAR PCB FROM
THE CN501 OF MAIN PCB AND THEN REMOVE THE
ASS'Y CASE-BATTERY IN THE DIRECTION OF ARROW.
ΠREMOVE 1 SCREW.
Fig. 4-6 Ass’y Case-Battery removal
Disassembly and Reassembly
Samsung Electronics 4-7
4-1-7 Ass’y Case-Bottom removal
Fig. 4-7 Ass’y Case-Bottom removal
´ REMOVE THE CASE- BOTTOM
IN THE DIRECTION OF ARROW.
ΠREMOVE 2 SCREWS.
Disassembly and Reassembly
4-8 Samsung Electronics
4-1-8 Ass’y-Deck removal
¨ REMOVE 1 SCREW.
ˇ REMOVE 2 SCREWS.
ˆ DISCONNECT THE FPC FROM THE ASS'Y DECK.
Ø DISCONNECT THE FPC FROM
THE CN501 OF MAIN PCB.
∏ REMOVE THE ASS'Y DECK IN THE DIRECTION OF ARROW .
Fig. 4-8 Audio PCB and Ass’y-Deck removal
Disassembly and Reassembly
Samsung Electronics 4-9
4-1-9 Ass’y Camera and Main PCB removal
CNC01
CNP01
ΠDESOLDER
ˇ DISCONNECT THE CNC01 FROM THE CNP01 OF MAIN PCB
AND THEN REMOVE THE ASS'Y CAMERA IN THE DIRECTION OF ARROW.
SOLDERING POINT
´ REMOVE 2 SCREWS.
Fig. 4-9 Ass’y Camera and Main PCB removal
Disassembly and Reassembly
4-10 Samsung Electronics
4-1-10 Ass’y LCD removal
"A"
ΠREMOVE 5 SCREWS.
´ REMOVE THE ASS'Y LCD IN THE DIRECTION OF ARROW "A".
Fig. 4-10 Ass’y LCD removal
Disassembly and Reassembly
Samsung Electronics 4-11
4-1-11 Ass’y EVF removal
¨ REMOVE THE ASS'Y EVF IN THE DIRECTION OF ARROW "B".
ΠDISCONNECT THE LEAD CONNECTOR FROM
THE CN803 OF FUNCTION MENU PCB.
´ REMOVE 1 SCREW.
ˇ REMOVE 3 SCREWS.
Fig. 4-11Ass’y EVF removal
Disassembly and Reassembly
4-12 Samsung Electronics
4-2 Circuit Boards Location
Fig. 4-12 Circuit Boards Location
NO. CONNECTOR DIRECTION CONNECTOR NO.
LOCA-NO. LOCA-NO.
2 CN101 MAIN PCB DECK -- 1
4 CN503 MAIN PCB DECK -- 3
7 CN501 MAIN PCB REAR CN961 8
19 CN892 MIC CPB MIC -- 18
11 CN851 MAIN PCB MIC PCB CN891 12
9 CNP03 MAIN PCB MIC PCB CN893 10
16 CNL201 LCD PCB MAIN PCB CN702 15
25 CNL301 LCD PCB LCD -- -26 CNL102 LCD PCB B/LIGHT -- --
-- CNE02 EVF MANU PCB CN803 24
21 CN805 FUNC MENU CN802 20
22 CN806 AE MENU CN802 20
14 CN801 MENU MAIN CN502 13
23 CN804 MENU SPEAKER -- -17 CNP02 MAIN PCB LENS -- --
5 CNP01 MAIN PCB CCD PCB CNC01 6
Disassembly and Reassembly
Samsung Electronics 4-13
4-3 Connector Diagram
FRONT PCB
Fig. 4-13 Connector Diagram
Fig. 4-14
Disassembly and Reassembly
4-14 Samsung Electronics
MEMO
Samsung Electronics 5-1
5. Alignment and Adjustment
5-1 Mechanical Adjustment
Test Point :
PB RF - Pin 45 of IC201
Head Switching Trigger - Pin 96 of IC601
Fig. 1 The location of test point
(PIN 45)
(PIN 96)
(PIN 67)
* Note 1 : Mechanical alignment is performed for the linearity of PB-RF(Envelope).
* Note 2 : Refer to the mechanism manual ÒDE-6Ó(AD68-30200A) for the mechanism alignment.
1) Short between pin #67 of IC601 and GND in order to set the TEST MODE.(ThatÕs Track Shift Mode)
2) Connect the Head SW Pulse in CH1 and the PB-RF in CH2 to oscilloscope.
3) Refer to the Fig1 for the location of test point.
4) Play the alignment tape supplied, and fit the PB-RF form like as Fig1.
(Refer to the alignment manual of the DE-6 described above).
5) If the alignment is completed, then remove the short wire for the release of the test mode.
Loading...