Samsung RS22HDHPNSR/AA-00, RS22HDHPNBC/AA-00 Owner’s Manual

100 % ,

Recycled Paper /

This manual is made with 100 % recycled paper.

the possibilities

Thank you for purchasing this Samsung product

Free Standing Appliance

Cont nt,s

SAFETY INFORMATION ........................................................................ 2

SETTING UP YOUR SIDE-BY-SIDE REFRIGERATOR ................................. 11

OPERATING THE SAMSUNG SIDE-BY-SIDE REFRIGERATOR ..................... 20

TROUBLESHOOTING ........................................................................... 35

SAFETY INFORMATION

Before using your new Samsung Side-By-Side Refrigerator, please read this manual thoroughly to ensure that you know how to operate the features

and functions that your new appliance offers safely and efficiently.

This appliance is not intended for use by persons (including children) with reduced physical,

sensory, or mental capabilities, or those who lack experience and knowledge, unless they have been given supervision or instruction concerning the use

of the appliance by a person responsible for their safety.

Because the following instructions cover various models, the characteristics of your refrigerator may differ slightly from the refrigerator described in this

manual. If you have any question, contact us at

1-800-SAMSUNG or find help and information online at www.samsung.com.

Important safety symbols and precautions:

/iX WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

Z_ CAUTION

Hazards or unsafe practices that may result in minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

_ Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall

socket.

Make sure the refrigerator is grounded to

3revent electric shock.

Call the contact center for help.

Note.

These warning symbols are here to prevent injury to you and others. Please follow them carefully. After reading this section, keep it in a safe place for future reference.

Engl sh - 2

,,_ WARNING

CRITICAL INSTALLATION WARNINGS

• Do not install the refrigerator in a damp location or place where it may come in

contact with water.

Deteriorated insulation on electrical parts may cause an electric shock or fire.

• Do not place this refrigerator in direct sunlight or expose it to the heat from stoves, room heaters, or other appliances.

• Do not plug several appliances into the same multiple power strip.

The refrigerator should always be plugged into

its own individual electrical outlet which has a

voltage rating that matches the voltage listed

on the refrigerator's rating plate.

This provides the best performance and

also prevents overloading of house wiring circuits, which could cause a fire hazard from overheated wires.

• Ifthe wall socket is loose, do not insert the power plug.

There is a risk of electric shock of fire.

• Do not use a power cord that has cracks or abrasion damage along its length or at either

end.

• Do not bend the power cord excessively or place heavy objects on it.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.

• When moving the refrigerator, be careful not to roll over or damage the power cord.

This may result in an electric shock or fire.

• Never unplug your refrigerator by pulling on the power cord.

Always grip the plug firmly and pull straight out from the outlet.

Damage to the cord may cause a short-circuit,

fire, and/or electric shock.

• Do not use aerosols near the refrigerator. Using aerosols near the refrigerator may cause

an explosion or fire.

• Do not install this appliance near a heater or inflammable material.

Engl sh - 3

• Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to direct sunlight or water (rain, etc.).

• Do not install this appliance in a location where gas may leak.

This may result in an electric shock or fire.

• This refrigerator must be properly

located and installed in accordance with the instructions in this manual

before you use it.

• Connect the power plug in the proper position with the cord hanging down.

Ifyou connect the power plug upside down, the

wire can get cut off and cause a fire or electric shock.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

This constitutes a fire hazard.

• Make sure that the power plug is not crushed or damaged by the back of the refrigerator.

• Keep the packing materials out of reach of children.

There is a risk of death from suffocation if a child puts the packing materials on his or her

head.

• The appliance must be positioned so that the

plug is accessible after installation. Failing to do so may result in an electric shock

or fire due to electric leakage.

• You need to remove all the protective plastic film before you initially plug the product in.

• The refrigerator must be safely grounded.

Always make sure that you have grounded the

refrigerator before attempting to investigate or repair any part of the appliance. Power leakages can cause severe electric

shock.

Never use gas pipes, telephone lines, or other potential lightning attractors as an electrical

ground.

Improper use of the grounding plug can result in a risk of electric shock.

If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord should

beAC 115-120 V, 10A, or more.

If a grounding adapter is used, make sure the

receptacleboxisfullygrounded. Plugthepowerplugintothewallsocketfirmly. Donotuseadamagedpowerplug,damaged powercord,orloosewallsocket.

Thismayresultinanelectricshockorfire.

Ifthepowercordisdamaged, haveitreplacedimmediatelybythe

manufactureroroneofitsservice agents.

z_ CAUTION

INSTALLATION CAUTIONS

• Allow sufficient space around the refrigerator and install it on a flat

surface.

Ifyour refrigerator is not level, the internal cooling system may not work correctly. Keep the ventilation space in the appliance enclosure or mounting structure clear of

obstructions.

• Allow the appliance to stand for 2 hours after installation.

• We strongly recommend you have a qualified

technician or service company install the

refrigerator. Failing to do so may result in an electric shock,

fire, explosion, problems with the product, or

injury.

z._ WARNING

CRITICAL USAGE WARNINGS

• Do not insert the power plug into a wall

socket with wet hands.

• Do not store articles on the top of the appliance.

When you open or close the door, the articles

may fall and cause personal injury and/or material damage.

• Do not insert hands, feet or metal objects (such as knives, etc.) into the bottom or the back of the refrigerator.

This may result in an electric shock or injury. Any sharp edges may cause a personal injury

• Do not put a container filled with water on the

refrigerator. If spilled, there is a risk of fire or electric shock.

• Children should be supervised to ensure that they do not play with the appliance.

Keep fingers out of "pinch point" areas.

Clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors if children are in the area.

• Do not let children hang on the door. A serious injury may occur.

• Do not let children go inside the refrigerator. They could become trapped.

• Do not insert your hands into the bottom area

under the appliance.

Any sharp edges may cause personal injury.

• Do not let children step on a drawer cover. The drawer may break and cause them to slip.

• Do not overfill the refrigerator with food. When you open the door, an item may fall out

and cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored inthe freezer with wet hands.

This may cause frostbite.

• Never put fingers or other objects into the water dispenser hole, ice chute, or ice maker bucket.

It may cause personal injury or material

damage.

• Do not use or place any substances sensitive to temperature such as inflammable sprays,

inflammable objects, dry ice, medicine, or

chemicals near or inside the refrigerator.

• Do not keep volatile or inflammable objects or substances (benzene, thinner, propane gas, alcohol, ether, LP gas, and other such

Engl sh - 4

products)intherefrigerator.

Thisrefrigeratorisforstoringfoodonly. Thismayresultinfireorexplosion.

• Donotstorepharmaceuticalproducts,scientific materials,ortemperaturesensitiveproductsin

therefrigerator.

Productsthatrequirestricttemperature controlsmustnotbestoredintherefrigerator.

• Donotplaceoruseanelectricalappliance insidetherefrigerator,unlessitisofatype recommendedbythemanufacturer.

• Donotstandontopoftheapplianceorplace objects(suchaslaundry,lightedcandles, lightedcigarettes,dishes,chemicals,metal objects,etc.)ontheappliance.

Thismayresultinanelectricshock,fire,

problemswiththeproduct,orinjury. Donotputacontainerfilledwithwateronthe appliance.

Ifspilled,thereisariskoffireorelectricshock.

• Donotusemechanicaldevicesoranyother meanstoacceleratethedefrostingprocess, otherthanthoserecommendedbythe

manufacturer.

• Donotdamagetherefrigerantcircuit.

• Donotsprayvolatilematerialsuchas insecticideontothesurfaceoftheappliance.

Aswellasbeingharmfultohumans,itmayalso

resultinanelectricshock,fire,orproblemswith

theproduct.

• NeverstaredirectlyattheUVLEDlampforlong periodsoftime.

Thismayresultineyestrainduetothe

ultravioletrays.

Becarefulwhenyouopenthedoorsifchildren

areinthearea.

• Donotletchildrenhangonthedoor. Aseriousinjurymayoccur.

• Donotletchildrengoinsidetherefrigerator. Theycouldbecometrapped.

• Bottlesshouldbestoredtightlytogethersothat theydonotfallout.

• Thisproductisintendedonlyforthestorageof foodinadomesticenvironment.

• Ifagasleakisdetected,avoidanynaked flamesorpotentialsourcesofignition,andair theroominwhichtheapplianceisstandingfor

severalminutes.

Donottouchtheapplianceorpowercord. Donotuseaventilatingfan.

Asparkmayresultinexplosionorfire.

• UseonlytheLEDLampsprovidedbythe

manufactureroritsserviceagents.

• Iftherefrigeratoremitsaburningsmell

orsmoke,unplugtherefrigerator immediatelyandcontactyour SamsungElectronicsservicecenter.

• Ifyouexperiencedifficultychanginganon-LED

light,contactaSamsungservicecenter.

• IftheproductisequippedwithLEDLamps,do

notdisassembletheLampCoversandLED Lampsyourself.

Pleasecontactyourserviceagents.

• Ifdustorwaterenterstherefrigerator,unplug therefrigeratorandcontactyourSamsung

Electronicsservicecenter.

Thereisariskoffire.

• Donotattempttorepair,disassemble, ormodifytheapplianceyourself.

Donotuseanyfuse(suchascooper,steelwire, etc.)otherthanastandardfuse.

Ifyourapplianceneedstoberepairedor reinstalled,contactyournearestservicecenter.

Failingtodosomayresultinanelectricshock,

fire,problemswiththeproduct,orinjury.

IftheinteriororexteriorLEDlamphasgone out,pleasecontactyournearestservicecenter.

• Childrenshouldbesupervisedto

ensurethattheydonotplaywiththe appliance.

Keepfingersoutof"pinchpoint"areas.: Clearancesbetweenthedoorsandcabinetare

necessarilysmall.

Englsh-5

,,_ CAUTION

USAGE CAUTIONS

• Do not re-freeze frozen foods that have thawed completely.

Do not place carbonated or fizzy drinks in the freezer compartment. Do not put bottles or glass containers

in the freezer.

When the contents freeze, the glass may break

and cause personal injury.

• Use only the ice maker provided with the refrigerator.

• Have the refrigerator's water supply installed by a suitably qualified person and connected only

to a potable water supply. To operate the ice maker properly, water

pressure of 20 - 125 psi (138 - 862 kPa) is required. Ifyou will be away from home for a long period of time (on vacation, for example) and won't be using the water or ice dispensers, close the

water valve. Otherwise, water leakage may occur.

• Ifyou won't be using the refrigerator for a very long period of time, (3 weeks or more) empty

the refrigerator, unplug it, close the water valve,

wipe excess moisture from the inside walls, and leave the doors open to prevent odors and mold.

• Service Warranty and Modification.

• Any changes or modifications performed by a 3rd party on this finished appliance are not covered under Samsung warranty service, nor is Samsung responsible for safety issues that result from 3rd party modifications.

• Do not block the air vents inside the refrigerator. Ifthe air vents are blocked, especially with a

plastic bag, the refrigerator can be over cooled. Ifthis cooling period lasts too long, the water

filter may break and cause water leakage.

• Ifthe refrigerator is disconnected from the power supply, you should wait for at least five minutes before plugging it back in.

• Ifyou have a long vacation planned or do not intend to use the refrigerator for a long period of

time, (3 weeks or more) empty the refrigerator,

pull out the power plug, close the water valve, wipe excess moisture from the inside walls,

and leave the doors open to prevent odors and

mold.

Letting the refrigerator run long periods of time without using it can cause the insulation to deteriorate and may cause a fire.

• To get the best performance from the product: Do not place food too close to the vents at the

rear of the appliance as it can obstruct free air

circulation in the refrigerator compartment. Wrap food up properly or place it in airtight containers before putting it into the refrigerator.

Do not place glass bottles or carbonated beverages into the freezer.

They can freeze and break.

Broken beverage containers can cause injury. Please observe maximum storage times and

expiration dates of frozen goods. There is no need to disconnect the refrigerator from the power supply if you will be away for

less than three weeks. However, if you will be away for more than

three weeks, remove all the food, unplug the

refrigerator, close the water valve, wipe excess moisture from the inside walls, and leave the

doors open to prevent odors and mold.

• Fillthe water tank and ice cube trays with potable water only (tap water, mineral water, or purified water).

Do not fill the tank with tea or a Sports drink.

This may damage the refrigerator.

• Do not strike or apply excessive force to any

glass surface.

Broken glass may result in a personal injury

and/or property damage.

• If the product is flooded, make sure to contact your nearest service center.

There is a risk of electric shock or fire.

Engl sh - 6

,,_ CAUTION

z._ WARNING

CLEANING CAUTIONS

+ Do not spray water directly on the

[_ + Use a clean, dry cloth to remove any

inside or outside the refrigerator

There is a risk of fire or electric shock.

Do not use a hair dryer to dry the inside of the refrigerator

Do not place a lighted candle in the refrigerator

to remove bad odors. This may result in an electric shock or fire.

foreign matter or dust from the power plug blades.

Do not use a wet or damp cloth when

cleaning the plug. Otherwise, there is a risk of fire or electric shock.

+ Before cleaning or performing

maintenance, unplug the appliance

from the wall socket. Failing to do so may result in an electric shock

or fire.

WARNING

+ This product contains chemicals known to

the State of California to cause cancer and

reproductive toxicity.

CRITICAL DISPOSAL WARNINGS

+ DANGER : Risk of child entrapment.

Before you throw away your old refrigerator or freezer:

Take off the doors and door latch.

Leave the shelves in place so that children cannot easily climb inside. Children trapped inside a refrigerator can hurt

themselves or suffocate to death.

+ Please dispose of the packaging material from

this product in an environmentally friendly

manner

+ Ensure that none of the pipes on the back of

the appliance are damaged prior to disposal.

+ R-600a or R-134a is used as a refrigerant.

Check the compressor label on the rear of the appliance or the rating label inside the fridge to see which refrigerant is used for your

refrigerator.

Ifthis product contains flammable gas

(Refrigerant R-600a), contact your local authority in regard to safe disposal of this

product.

+ When disposing of this refrigerator, remove the

door/door seals and door latch so that small children or animals cannot become trapped

inside. Children should be supervised to ensure that

they do not play with the appliance.

Iftrapped inside, the child may get hurt or suffocate to death.

+ Cyclopentane is used in the insulation.

The gases in the insulation material require a special disposal procedure.

Please contact your local authorities in regard to the environmentally safe disposal of this

product.

+ Keep all packaging materials well out of the

reach of children, as packaging materials can

be dangerous to children.

If a child places a bag over his or her head, the child could suffocate.

Engl sh + 7

I'_ ADDITIONAL TIPS FOR

PROPER USAGE

• Inthe event of a power failure, call the local office of your Electricity Company and ask how long it is going to last.

Most power failures that are corrected in an hour or two will not affect your refrigerator

temperatures. However, you should minimize the number of door openings while the power

is off. Should the power failure last more than 24

hours, remove and discard all frozen food.

• If a key is provided with refrigerator, the keys should be kept out of the reach of children and not be kept in the vicinity of the appliance.

• The appliance might not operate consistently (frozen contents can thaw or temperatures

can become too warm in the frozen food compartment) when sited for an extended

period of time in a location where ambient air temperatures are constantly below the

temperatures for which the appliance is

designed.

• Do not store food which goes bad easily at low

temperature, such as bananas and melons.

,, Your appliance is frost free, which means there

is no need to manually defrost your appliance.

This will be carried out automatically.

• Temperature rise during defrosting complies with ISO requirements. But Ifyou want to prevent an undue rise in the

temperature of frozen food while the appliance

defrosts, wrap the frozen food in several layers of newspaper.

• Any increase in the temperature of frozen food during defrosting can shorten its storage life.

• Do not re-freeze frozen foods that have thawed completely.

Saving Energy Tips

Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat (a

radiator, for example).

Never block any vents or grilles on the appliance. Allow warm food to cool down before placing it

in the appliance.

Put frozen food inthe refrigerator to thaw. You can then use the low temperatures of the frozen products to cool food inthe refrigerator.

Do not keep the door of the appliance open for too long when putting food in or taking food

out. The shorter the time the door is open, the less

frost build-up you'll have in the freezer.

Provide sufficient clearance to the right, left,

back, and top for air circulation when installing the refrigerator. This will help reduce power consumption and keep your energy bills lower.

Engl sh - 8

1. Regulatory Notice

1.1 FCC Notice

/_X FCC CAUTION:

CAUTION

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Contains Transmitter Module FCC ID: A3LSWL-B70F This device complies with Part 15 of FCC Rules. Operation is Subject to the following two conditions:

(1)This device may not cause harmful interference, and (2)This device must accept any interference received including interference that cause undesired

operation.

For products available in the US and Canadian markets, only channels 1+11 are available. You cannot select other channels.

FCC STATEMENT:

This equipment has been tested and found to comply within the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur ina particular installation. Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

+ Reorient or relocate the receiving antenna + Increase the separation between the equipment and receiver + Connect the equipment to an outlet that is on a different circuit than the receiver. + Consult the dealer or an experienced radio/TV technician for help.

FCC RADIATION EXPOSURE STATEMENT:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there is at least 8 inches (20 cm) between the

radiator and your body. This device and it's antennas must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product

procedures.

SAVE THESE INSTRUCTIONS

Eng+sh - 9

1. Regulatory Notice

1.2 IC Notice

Contains Transmitter Module IO: 649E - SWLB70F The term "10" before the radio certification number only signifies that Industry Canada technical

specifications were met. Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may

cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-O03.

Cet appareil numerique de laclasse Best conforme a la norme NMB-O03 du Canada.

For products available in the US and Canadian markets, only channels 1-11 are available. You cannot select other channels.

IC RADiATiON EXPOSURE STATEMENT:

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated so there is at least 8 inches (20 cm)

between the radiator and your body. This device and it's antennas must not be co-located or operated in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter

product procedures.

SAVE THESE iNSTRUCTiONS

Engl sh - 10

/©UF

sdo by sdo

GETTING READY TO INSTALL THE REFRIGERATOR

Congratulations on your purchase of this Samsung Side-By-Side Refrigerator. We hope you enjoy the state-of-art features and

efficiencies that this new appliance offers.

Selecting the best location for the refrigerator

Choose:

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a level floor.

• A location with enough space for the refrigerator doors to open easily.

• A location that provides sufficient space to the right, left, back, and top for air circulation.

• A location that allows you to move the refrigerator easily if it needs maintenance or

service.

important: Make sure that you can easily move your refrigerator to its final location by measuring

doorways (both width and height), thresholds, ceilings, stairways, etc.

The following chart details the exact height and depth of this Samsung French Door Refrigerator.

Model

Depth "A"

Width "B"

Height "C"

OverallHeight "D"

Depth "E"

RS22HDHPN**

27" (687 mm)

35 7/8" (912 mm)

68 1/2" (1742 mm)

70 1/8" (1782 mm)

30" (762 mm)

2" (5 0

If the refrigerator does not have enough space, the internal cooling system may not work properly.

If your refrigerator has an ice maker, allow extra space at the back for the water line connections.

When you install the refrigerator next to a fixed wall, you need a minimum clearance of 2" (50 mm) between the refrigerator and wall to allow the door

to swing open.

Engl sh - 11

o llow clearance to the right, left, back

and top when installing. This will help reduce power consumption

and keep your energy bills lower.

• Do not install the refrigerator where the temperature will go below 50 °F (10 °C).

• Do not locate the refrigerator where it may

become wet.

• Make sure you disconnect the water supply line

BEFORE removing the freezer door.

See the next section on "Separating the Water

Line" to avoid damage.

Door Clearance

68" (17213 mm)

CAUTION

When moving your refrigerator To prevent floor damage, be sure the front

adjusting legs are in the up position (above the floor).

Refer to 'Leveling the Refrigerator' on page 15.

Flooring

For proper installation, you must place this refrigerator on a level, hard surface that is the same height as the rest of the floor.

This surface should be strong enough to support a fully loaded refrigerator.

To protect the finish of the flooring, cut a large section of the cardboard carton and place it under the refrigerator where you are working.

When moving the refrigerator, you need to pull and push it straight forwards or back.

Do not wiggle it from side to side.

Required Tools (Not provided)

Leg Screw Driver

Philips Flat-bladescrew Socket wrench

screwdriver(+) driver(-) (13/32")(10 ram)

Allenwrench

(3/16")(5 mm)

Engl sh --12

REMOVING THE REFRIGERATOR DOORS

if your entrance won't allow the refrigerator to pass easily through it, you can remove the refrigerator

doors, To remvoe the doors, follow the steps below,

if you do not need to remove the doors, go to "Leveling the Refrigerator" on page 15,

1. Removing the front leg cover

Open both the freezer and refrigerator doors, Unscrew the three screws holding the front leg

cover in place by turning them counter-clockwise. When the screws are loose, remove the front leg

cover.

2. Separate the water supply line from the refrigerator

Remove two water lines (orange for ice and the other for water) by pressing the coupler ( 1 ) and

pulling the water line (2 ) away.

3. Removing the freezer door

A few things to mention first. + Make sure that you lift the door straight up so

the hinges are not bent or broken,

+ Be careful not to pinch the water tubing and

wire harness on the door,

+ Place doors on a protected surface to prevent

scratching or damage,

With the Freezer door closed, remove the

upper hinge cover ( 1 ) using a screwdriver,

and then disconnect the wires by gently pulling them apart (2 ),

Remove the hinge screws (3 ) by turning them

counterclockwise, and then take off the upper

hinge ( 4 ). Be careful that the door does not fall on you as

you are removing the hinge,

Do not cut the water line, Gently separate it from the coupler,

z_ CAUTION

Be sure to keep track of all parts you are removing,

Engl sh --13

3.Next,removethedoorfromthelowerhinge (5)bycarefullyliftingthedoorstraightup(6).

iiiiiii!ii:iiii!iiiiii',_,,! . % iiiiii!iii_iiii!iiiiD

Z_ CAUTION

Remove hinge screws (3 ) and the ground screw (2 ) by turning counter-clockwise, and then take off the upper hinge ( 4 ).

Be careful that the door does not fall on you as you are removing the hinge.

Be careful not to pinch the water tubing and wire harness on the door,

4. Remove the lower hinge ( 7 ) from the bracket (8 ) by gently lifting the lower hinge upwards.

4. Remove the Fridge Door

1. With the door closed, remove the upper hinge cover ( 1 ) using a screwdriver.

CAUTION

Be sure to keep track of all parts you are removing.

Remove the door from the lower hinge ( 5 ) by lifting the door straight up ( 6 ).

4. Remove the lower hinge ( 7 ) from the bracket ( 8 ) by gently lifting the lower hinge upwards.

(7)

(8)

5. After you have removed the Fridge and Freezer

doors, move the refrigerator to its installation

location.

Engl sh --14

Re-attachingtheFridgeDoor Tore-attachthefridgedoor,replacepartsin

reverseorder,

Re-attachingtheFreezerDoor Tore-attachthefreezerdoor,replacepartsin

reverseorder,

Re-attaching the Water Supply Lines

1. The Water Lines must be fully inserted into the center of the transparent coupler to prevent

water leakage from the dispenser.

2. insert the 2 clips in the install pack as shown below, and then confirm that each clip holds

the line firmly,

Before levelling the refrigerator, remove

the front leg cover.

Open both the freezer and refrigerator doors. Unscrew the three screws holding the front leg

cover in place by turning them counter-clockwise. When the screws are loose, remove the front leg

cover,

Center of Transparent coupler

Clip A (1/4") (6,35 ram)

z_ CAUTION

Make sure the color of the water lines match, Keep the clips out of the reach of children and

make sure that children do not play with them or put them into their mouths,

LEVELING THE REFRIGERATOR

Make sure the refrigerator is level so that you can make final adjustments.

Use a level to test if the refrigerator is level both side to side and back to front,

if the refrigerator is not level, you will not be able to get the doors perfectly even, which may cause

moisture condensation and increased energy bills,

When the Freezer part is lower than the

Fridge part.

insert a flat-blade screwdriver into a slot on the Freezer Leg, then turn it clockwise,

When the Fridge part is lower than the

Freezer part.

insert a flat-blade screwdriver into a slot on the Fridge Leg, then turn it clockwise.

Screw Driver Leg

[_ efer to the next section for the best way

to make very minor adjustments to the

doors,

[_ he front of the refrigerator is also

adjustable,

Engl sh --15

MAKING MINOR ADJUSTMENTS TO THE DOORS

A level refrigerator is necessary for getting the doors perfectly even, Make sure your refrigerator is level before you

begin. if you need help leveling, review the )revious

section on leveling the refrigerator,

2, Adjust the height difference between the doors

by turning the bolt (2 ) clockwise ( ) or

counter clockwise ( ).

When the door of the freezer is higher than

ustment part

The process for adjusting each door is the same, Open the doors and adjust them, one at a time, as

follows:

1, Unscrew the nut ( 1 ) from the lower hinge until

it reaches the upper end of the bolt (2 ).

When you release the nut ( 1 ), make sure

that you use the Allen wrench provided

(3 ) to loosen the bolt (2 ) in a counter- clockwise direction.

You should then be able to unscrew the

nut ( 1 ) with your fingers,

the fridge

nch

[_ hen you turn clockwise ( ), the

door will move up,

3, After adjusting the doors, turn the nut ( 1 )

clockwise ( ) until it reaches the lower end of the bolt, then tighten the bolt again with

the wrench ( 3 ) to fix the nut in place ( 1 ).

iiiiiiiiiiiill¸_!___!!_!!i_!ii!_i!ii!_i!ii!_i!ii!iii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!ii!i!iiiiii_i_i!iiii!i!i!_!ii

if you do not secure the nut firmly, the bolt may release,

Engl sh --16

Installingthewaterfilter.

(_ eforeinstallingthewaterfilter,please

removethetopshell

Cover filter

1.Removethewaterfiltercover(1).

2.Removethefixedcapbyturningitcounter clockwise.

Keepthecapinasafeplaceforlateruseifyou don'tuseafilter.

3.Removethewaterfilterfromtheboxandput areplacementindicatorstickeronthefilteras

shown. Placeastickeronthefilterwithadatesix

monthsinthefuture. Forexample,ifyouinstallthewaterfilterin

March,putthe"SEP"stickeronthefilterto remindyoutoreplaceitinSeptember.

Thatwayyou'llknowwhenitistimetoreplace thefilter.

Normalfilterlifeisabout6months.

(1)

Sticke

(month indicator)

the indicator mark

RemoVe the red cap on the filter with the

A newly installed water filter cartridge may

cause water to briefly spurt from the water dispenser.

This is caused by air getting into the line.

it should pose no problem to operation.

lock indicator on the

filter housing,

iiiiiiiiiiiiiiii iiiiiiiiiiiiiiii

4. Remove the filter cap and insert the filter into

the filter housing.

5. Slowly turn the water filter 90 ° clockwise to align the indicator mark on the filter with lock

indicator on the filter housing. Make sure to align the water filter label

mark with the center of the lock indicator as illustrated above, right. Do not over-tighten.

Engl sh --17

INSTALLING THE WATER DISPENSER LINE

A water dispenser is one of the helpful features on your new Samsung Refrigerator. To help promote better health, the Samsung water

filter removes unwanted particles from your water. However, it does not sterilize or destroy

microorganisms. You may need to purchase a water purifying system to do that.

The water line also connects to the ice maker. For the ice maker to operate properly, water

pressure of 20 - 125 psi (138 - 862 kPa) is required. If the refrigerator is installed in an area with low

water pressure (below 20 psi), you can install a booster pump to compensate for the low pressure.

After you have connected the water line, make sure the water storage tank inside the refrigerator is properly filled.

To do this, press the water dispenser lever until water runs from the water dispenser.

Water line installation kits are available at

extra cost from your dealer.

We recommend using a water supply kit that contains copper tubing.

Connecting to the water supply line

1. First, shut off the main water supply line and

turn the ice-maker off.

2. Locate the nearest cold water drinking water line.

3. Install the pipe clamp and shut off valve.

4. Connect the water line installation kit to the shut off valve.

Cold water line --

Water line installation kit

Pipe clamp

Shut off valve

Connecting the water supply line to the refrigerator

There are several items that you need to purchase to complete this connection.

You may find these items sold as a kit at your local hardware store.

Use Copper Tubing Use Plastic Tubing ® 1/4"copper tubing ® 1/4"plastic tubing ® 1_,,compression nut _ Melded end (Bulb)

(1pc) ® 1/4"compression nut

® Ferrule (2pc) (1pc)

Refrigerator

Plastic Tubing

Compression Nat

(1/4") (Assembled) _ Compression

l/ (Assembled)

Fitting (Assembled)

°tsupp"ed)i€ i

iJ&___ t_ Comp.... _on

_ nut (B) (1/4")

(Not supplied)

Copper tubing or Plastic tubing (B)

(Not supplied) (Not supplied)

_. Household water supply line

1. Connect the household water line to the assembled compression fitting.

Ifyou are using copper tubing, slip the

compression nut ( B ) (not supplied) and ferrule (not supplied) on the copper tubing (not supplied) as shown.

Ifyou are using plastic tubing ( B ), insert the molded end (Bulb) of the plastic tubing ( B ) into

the compression fitting.

/k CAUTION

Do not use plastic tubing ( B ) without the molded

end (Bulb).

Engl sh - 18

2.Tightenthecompressionnut(B)ontothe compressionfitting. Donotover-tightenthecompressionnut(B).

3.Turnthewateronandcheckforanyleaks insidetherefrigerator,aroundthewaterfilter,

andinanyconnectionareas. Ifyoufindwaterdropsorleaks,turnoffthe mainwatersupply.

Iftheleaksareintheconnectionareas,check

theconnectionsand,ifnecessary,tighten.

Ifthereareleaksintherefrigerator,check

thewaterfilterandconfirmitisinthelocked

position.

Turnonthewatersupplyandcheckforleaks

again.

4.Plugintherefrigerator.

5.Flush3gallonsofwaterthroughthefilterbefore drinkingorusingthewaterfromtherefrigerator.

(Flushapproximately6minutes.)

Thiswillcleanthewatersupplysystemand

removeairfromthelines.

Toflush,presstheWaterbutton,andthenpress alargeglassorcupagainstthewaterdispenser

lever.Filltheglass,emptyitintothekitchensink afteritisfilled,andthenrepeat.

[_ dditionalflushingmayberequiredin

somehouseholds.

6.Opentherefrigeratordoorandmakesurethere arenowaterleakscomingfromthewaterfilter.

After you turn on the refrigerator, let the

ice maker make ice for 1 to 2 days.

Over that period of time, throw out the

first 1 or 2 buckets of ice the ice maker makes to ensure all impurities have been

removed from the water line.

Only connect the water line to a drinkable water

source.

Ifyou have to repair or disassemble the water line, cut off 1/4" of the plastic tubing to make

sure you get a snug, leak-free connection.

You can test the water line quickly using a

paper cup. Under normal conditions, the water dispenser

can fill a 5.75 oz. (170 cc) cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate location with reasonable clearance between it

and the wall. Refer to installation instructions in this manual.

2. Once the refrigerator is plugged in, make sure the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest temperature and wait for an hour. The freezer will get slightly chilled and the motor

will run smoothly.

Reset the refrigerator and freezer to the

temperatures you want.

4. After you plug the refrigerator in, it will take a few hours to reach the appropriate

temperature. You can store food and drinks in the refrigerator

after the temperature is sufficiently cool.

If condensation or water drops appear

on both sides of the fridge door's central part, turn the Energy Saver mode off after

removing the condensation. (See the explanation of the Energy Saver button in "Using the Control Panel" on

page 20.)

Engl sh - 19

G side-

USING THE CONTROL PANEL/ DIGITAL DISPLAY

• Press the Power Freeze button to decrease the time needed to freeze

products in the Freezer.

iiiiiiiiiiiii@!!!Biii!ii!iii!iiiiiii!ii!ii!i

iiiiii:ilili_eez_:!:!:

iiiiiiiiiL

This can be helpful if you need to quickly freeze items that spoil easily

or if the temperature in the freezer has warmed dramatically.

(For example, if the door was left open)•

2. The Override function activates/ deactivates Smart Grid (page 25).

Press the Power Freezer/Override button for 3 seconds to set/clear the Override function•

For better energy efficiency, press the Energy Saver button• If condensation occurs on the doors,

press again to turn the Energy Saver Button function off.

When you change the water filter, press

2. and hold this button for 3 seconds to

reset the water filter indicator•

1. Press the Lighting button to turn on the dispenser LED lamp.

2. To switch the temperature units between °C and °F, press and hold this

button for 3 seconds•

Press the Fridge button to set the Fridge

temperature. You can set temperature between 44 °F

(7 °O) and 34 °F (1 °C).

The Power Cool function starts operating when you set the temperature lower than

34 °F (1 °0). If you select "Power Cool", the inside

temperature of the Fridge will decrease for

about two and a half hours•

When the Power Cool mode exits, the

notch is reset to the factory default

_iliii_l_lilllliiii_ii!ii!ii!ii!ii!ii!ii!ii!ii!ii@ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_iiiiii!i!_

Press the Ice Off button to turn the ice making function off.

Press and hold this button for 3 seconds, to turn on the Chid lock and lock all the panel buttons, including the

Ice button and the dispensers• To cancel this function, press and hold

this button for 3 seconds again•

Press the Ice button to choose cubed or crushed ice.

Press the Water button for water.

USING THE DIGITAL DISPLAY

" Freezer Temp/' indicates the current Freezer temperature.

" Fridge Temp." indicates the current Fridge temperature.

When not in use, the Display will turn off. This is normal operation.

iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii

Each time you press and hold the button

for 3 seconds, the °C and °F temperature

modes alternate and the °C or °F icon lights up, indicating your selection.

Engl sh --20

Power Freeze ®

This icon lights when you activate the "Power Freeze" feature. "Power Freeze" is great for times

when you need a lot of ice. When you have enough, just press the button

again to cancel the "Power Freeze" mode.

When you use this function the energy

consumption of the refrigerator will increase.

Remember to turn it off when you don't need it and return the freezer to your

original temperature setting.

Energy Saver

This icon lights when you activate the "Energy Saver" function.

The Energy Saver function is automatically set to "ON" when power is supplied to the Refrigerator.

If condensation appears on the doors, turn the Energy Saver function off.

E-Smart

The E-Smart icon lets you check the status of the refrigerator's AP connection (network connection).

• When connected to an AP: The E-Smart icon is on.

• When not connected to an AP: The E-Smart icon is off.

Power Cool (_

This icon lights when you activate the "Power Cool" feature (refer to number 5, Fridge Button on

Page 20 to select this function). For a quick fridge cool down, use "Power Cool".

Ifyou select "Power Cool", the inside temperature

of the Fridge will decrease for about two and a half hours.

Filter indicator

This icon lights when you need to change the filter, usually after the refrigerator has dispensed

about 300 gallons of water (after about 6 months). After you install the new water filter, reset the filter

indicator by touching and holding the "Energy Saver" button for 3 seconds.

If water is not dispensing or dispensing slowly,

you need to replace the water filter because the water filter is clogged.

• Some areas have large amounts of lime in their water, which causes the water filter to clog

more quickly.

Cubed ice _, Crushed ice

Enjoy cubed or crushed ice by selecting your preference on the digital control panel. The ice type light indicates the type of ice that is

currently chosen.

Lighting ..0,.

This icon lights when you activate the "Lighting" feature. When the icon is lit, the dispenser light (under the display) is on continuously.

If you want the Dispenser lamp to come on only when some one uses the dispenser, press the

Lighting button to turn the continuous mode off.

Water _/

This icon lights when you activate the "Water" feature.

ice Off

This icon lights when you activate the "Ice Off" feature. The ice maker is turned off and will not

produce ice. When ICE OFF blinks on the display panel, reinsert

the ice bucket and/or make sure it's installed properly.

English- 21

Child Lock f_

This icon lights when you activate the "Lock" feature.

When the Child Lock icon is lit, all the panel buttons, including the Ice button and the

dispensers, are locked and de-activated. Press and hold the Ice Off / Child Lock button for

3 seconds to turn Child Lock off and re-activate the panel buttons.

Cooling Off Mode

Cooling Off mode (also called Shop mode), is designed for use by retailers when they are

displaying refrigerators on the shop floor. In Cooling Off mode, the refrigerator's fan motor

and lights work normally, but the compressors do not run, and the refrigerator and freezer do not get

cold. To start Cooling Off mode, touch and hold the

Power Freeze button and the Freezer button for 5 seconds during normal operation.

The refrigerator chime sounds and OFF appears on the display.

To cancel Cooling Off mode, touch and hold the Power Freeze and Freezer buttons again for

5 seconds, until the chime sounds.

Important: If you see the OFF code on your refrigerator's display, your refrigerator is in Cooling

Off mode. Follow the directions above to cancel.

Display Off Function

To energy conservation the Panel Display turns off automatically under the following conditions: When no button has been pressed, when no doors

are open, or when no Dispenser Lever has been pushed for a period of time.

However, the icon indicating your Water or Cubed / Crushed Ice selection, will stay on. When you press a button, open a door, or push

a Dispenser Lever, the Panel Display will turn on again.

Except for the Water and Cubed / Crushed Ice buttons, all function buttons will become operational after you remove your finger from the

button you are currently pressing.

E-SMART Refrigerator Features

How to get the most out of your E-Smart refrigerator.

Getting Connected

To use the Smart Grid (Demand Response) and E-Smart function on your Refrigerator, you need the following devices and apps:

• Devices: 1) Wireless Router, 2) Samsung

E-Smart Refrigerator, 3) Smartphone (Recommended: Galaxy S4,Galaxy Note3/

Android OS Jelly bean). Applications: 1) "Samsung E-Smart App" from

the Google Play Store or Samsung Apps.

Cooli

addition, you need to:

Connect the Refrigerator and the Smartphone to the same Wi-Fi network inyour home.

Install and run Samsung E-Smart App on your

Smartphone (to use the Samsung E-Smart function).

In addition, to use the Smart Grid (Demand Response) function, you must Register for the

service with your electric company. The company must have an EMS (Energy

Management System) that supports SEP (Smart Energy profile).

Engl sh --22

Downloading the E-Smart App and Connecting the Refrigerator to your

Network

1, On your Smartphone, connect to the app store

(e.g. Google Play, etc.).

2, Search for the app using "Samsung E-Smart

Ref." as the keyword.

3, Download the app and install it on your phone, 4, Launch the app,

The network configuration screen appears.

5, Configure the AP information (SSiD, Password,

etc.) on the app screen.

6, Configure the network settings according to the

instructions in the app.

7, On the refrigerator, press and hold the Fridge

and Energy Saver buttons at the same time for 3 seconds.

The refrigerator enters the AP mode.

8, if you have completed the network settings

properly, the app shows the home screen,

• Please confirm your the Internet devices (AP,

Smartphone) are working properly before configuring the network settings,

This refrigerator supports the IEEE 802,11 a/b/g/n protocols.

Samsung Electronics recommends IEEE

802.11 n. To connect the refrigerator to a wireless

network, you have to connect the refrigerator to

an AP (router or modem).

if the AP supports DHCP, you can connect the refrigerator to the Internet using DHCP or a

fixed IP address. Set the channel of the AP to one not currently

being used. if the channel set for the AP is being used

by another device nearby, it may result in interference.

Most wireless networks allow you to configure network security settings, if your network

has a security password, you must enter the password to connect to the network,

The refrigerator supports the following wireless security modes and encryption types:

Security Mode: WEP, WPAPSK, WPA2PSK

Encryption Type: WEP, TKIP, AES

(WPA2PSK and AES are recommended,) The app supports indoor control only. The Samsung E-Smart Ref, app is optimized

for Samsung Electronics Smartphones (Galaxy $4, Galaxy Note 3).

For other Smartphones, some functions may work differently,

iiiiiiiiiiiiiiii

Engl sh --23

MAC Address Display Mode

This function displays the MAC address of the Wi-Fi module on the refrigerator display. The refrigerator displays the MAC address of the

Wi-Fi module for 1 minute,

1, Press and hold the Power Freeze and Energy

Saver buttons at the same time for 3 seconds,

2, A Buzzer sounds. Four of the twelve Mac

address of the Wi-Fi module are displayed in turns in the freezer and fridge temperature displays for 1 minute. For example, if the Wi-Fi

module's MAC address is "11-22-33-44-55- 66", the MAC address is displayed as follows:

"11 22" _ "33 44" _ "55 66" _ ..... "11 22"

for 1 minute.

3, After 1 minute, the display returns to the normal

state and the Buzzer sounds again,

Ifthe Mac addresses are not available or

there is no Wi-Fi module," .... ' is displayed

on the freezer and fridge temperature displays,

SMART GRID Function (Demand Response)

When the refrigerator operates in SMART GRID (Demand Response) mode, the E-Smart Refrigerator function can control energy usage

or delay the operation of some functions to save money when energy prices or demand are the

highest,

[_ ou can deactivate the SMART GRiD

(Demand Response) function at any

time.

(Using the Override On/Off function}

To use the SMART GRiD (Demand Response) function, you need a

separate contract with your utility company.

Using the SMART GRID (Demand Response) Function

This feature monitors energy prices and demand information from your utility company and sends

notifications to the refrigerator to run high energy- consuming tasks during off-peak times when

electricity costs and demand are lower. If the refrigerator receives a control signal from

the Utility Company, the refrigerator will display the DAL (L3) - TALR (L4) levels on the refrigerator

display and control the power consumption according to the level.

]Exception condition] The DAL and TALR control signals from an utility company work as long as product performance is maintained,

If the refrigerator receives the SMART GRID (Demand Response) signal (DAL or TALR), the

refrigerator will operate in Delay Appliance Load (Display: L3) or Temporary Appliance Load Reduction (Display: L4) mode,

Engl sh --24

DelayApplianceLoad(L3):Therefrigerator respondstoaDALsignalbyprovidinga

moderateloadreductionforthedurationofthe delayperiod.

Thisfunctioncontrolsfunctionsthatconsume

alotofenergysuchasadjustingtheCooling system,runningthedefrostcycle,andmaking

ice.

WhentherefrigeratoroperatesinDAL(L3)

mode,"L3"isdisplayedontherefrigerator display,

DALmodeisautomaticallydeactivatedafter itlastsfortheamountoftimestipulatedby

theDALsignal(max.4.5hours)orwhenthe

Overridekeyispressed,

TemporaryApplianceLoadReduction(L4): TherefrigeratorrespondstoaTALRsignalby

aggressivelyreducingtheloadforashorttime period,

Thisfunctionreducesenergyconsumptionby

stoppingthecompressorandcontrollingthe

functionsthatconsumealotofenergysuchas thedefrostcycleandmakingice.)

WhentherefrigeratoroperatesinTALR(L4)

mode,"L4"isdisplayedontherefrigerator display.

TALR(L4)modeisautomaticallydeactivated

afteritlastsfortilereceivedduration(max.15 minutes),orwhentheOverridekeyispressed,

Themodeisimmediatelydeactivatedandthe

refrigeratorreturnstothenormalstatewhen

thedoorisopenedorclosed,orthedispenser

isused,

Activating and deactivating Override mode

1, Press and hold the [Power Freeze[ button for 3

seconds.

2. A buzzer sounds and "Or' and "on' is displayed in the freezer and fridge temperature displays

for 5 seconds.

3. Ifthe refrigerator receives a SMART GRID (Demand Response) signal from the Utility

Company, "Or' is displayed in the freezer temperature display,

4. To deactivate OVERRIDE mode, press and hold

the [Power Freeze[ button for 3 seconds,

5. A buzzer sounds and 'Or' and 'oF'appears in

the freezer and fridge temperature displays for 5 seconds,

Override Mode

When you want to ignore the SMART GRID (Demand Response) signal from the Utility

Company, you can activate OVERRIDE mode. If OVERRIDE mode is activated, the SMART

GRID (Demand Response) signal is ignored and the refrigerator will not be controlled by the Utility

Company,

Engl sh --25

Alternatively, you can activate or

deactivate OVERRIDE mode using the app.

Using the E-SMART Function 4.

The E-SMART function enables you to control and monitor your E-Smart refrigerator remotely for your

convenience.

+ o use the E-SMART refrigerator

functions, you have to install the corresponding app first.

+ The app supports indoor control only.

1. Operational Status, User Settings & Messages. + You can view the freezer and fridge temperature

settings.

+ You can receive an alarm when the freezer or

fridge door is open for 2 minutes.

+ The door-open alarm indicator appears on the

status bar of the top area of your mobile phone.

+ You can check the DR and Override status. + You can check the operational condition of the

ice maker in the freezer.

2. Remote Management. + Power Freeze Setting :You can remotely

activate the Power Freeze function.

+ Power Cool Setting : You can remotely activate

the Power Cool function.

+ Ice On/Off Setting : You can remotely set up

the Ice On/Off Setting function.

3. Energy Consumption Reporting. + Shows the accumulated power consumption.

Power consumption data is updated every 10 minutes.

The energy consumption report may

differ from the power consumption specifications of the product depending on

the operating environment and the stored food.

Delay Defrost Capability.

The Delay Defrost Capability function saves energy by delaying the defrost operation to a

time specified by the user. You can configure the time, and this function

will save energy during the specified period in a 24 hour cycle. Ifthe time is not set, the function works with the default time settings.

The default time settings are below: 6 am to 10 am : 1st. November + 30th. April 3 pmto 7 pm: 1st. May + 31th. October

To change the time setting for the Delay

Defrost Capability

You can change the time setting for the Delay

Defrost Capability on the app.

Provision for Open Access to the

Connected Product Requirements

1. SGIP Open Standards (Smart Energy Profile 2.0 http://www.csep.org/)

+ Energy Consumption Reporting + Demand Response

2. Samsung OPEN API + Operational Status, User Settings & Messages

ICE Maker Status: GET/external/ icestatus?icegetstatus=opt (relevant to the

energy consumption of the product 1)

Door Open Alarm: GET/devices/0/ Door?type=opt (relevant to the energy

consumption of the product 2)

DR Status: GET/external/drlc?drgetstatus=opt

+ Delay Defrost Capability

Set Schedule of the Defrost Delay: POST / devices/0/defrost/addSchedule

Get Schedule of the Defrost Delay : GET / devices/0/defrost/getSchedule

Delete Schedule of the Defrost Delay: POST /

devices/0/defrost/delSchedule

Defrost Delay On/OFF: PUT/devices/0/defrost/

delayevent.

Eng+sh- 26

CONTROLLING THE TEMPERATURE

Basic Temperature of Freezer and Fridge

The basic and recommended temperature of Freezer and Fridge compartments are 0 °F (-18 °C)

/ 37 °F (3 °C). If the temperature of Freezer and Fridge

compartments are too high or low, adjust the temperature manually.

Controlling the Freezer temperature

i_eoft

--i

needs. Press the Freezer button repeatedly until the

desired temperature is shown in the temperature display.

Fahrenheit : 0 °F 4 -1 °F4 -2 °F4 -3 °F4

-4 °F4 -5 °F 4 -6 °F4 -7 °F 4 -8 °F4 5 °F4 4OF43OF42OF41 oF4OOR

Centigrade : -18 °C 4 -19 °C 4 -20 °C 4 -21 °C 4 -22 °04 -23 °C4 -15 °C4 -16 °C4 -17 °C

4 -18 °C.

Keep in mind that foods like ice cream may melt at 4 °F (-15.5 °C).

The temperature display will move sequentially from 5 °F (-15 °0) to -8 °F (-23 °0).

When the display reaches 5 °F (-15 °C), it will begin again at -8 °F (-23 °0).

Controlling the Fddge temperature

The refrigerator temperature can be set between 44 °F (7 °0) and 34 °F (1 °0) to suit your particular

needs.

Press the Fridge button repeatedly until the desired

temperature is shown in the temperature display.

Fahrenheit : 37 °F 4 36 °F 4 35 °F 4 34 °F 4 Power Cool 4 44 °F4 43 °F4 42 °F4 41 °F4

40 °F4 39 °F4 38 °F 437 °R Centigrade : 3 °C 4 2 °C 4 1 °C 4 Power Cool

4 7 oC 4 6 oC 4 5 oC 4 4 oC4 3 oC.

The temperature control process for the Fridge works just like the Freezer process.

Press the Fridge button to set your desired

temperature. After a few seconds, the Fridge will begin tracking

towards the newly set temperature. This will be reflected in the digital display.

* he temperature of the freezer or the

refrigerator may rise if you open the doors too frequently, or if a large amount of warm or hot food is placed in either

side.

* This may cause the digital display to blink.

Once the freezer and refrigerator return to their

normal set temperatures the blinking will stop.

* Ifthe blinking continues, you may need to

"reset" the refrigerator. Unplug the appliance, wait about 10 minutes,

and then plug it back in.

Eng+sh +27

USING THE iCE AND COLD WATER DISPENSER

When ice Off blinks on the display panel, reinsert the ice bucket and / or make sure it's installed

properly,

Cubed Crushed Water IceOff

Select this if you want to : °

NO ICE

turn the ice maker off.

Using the Water Dispenser

Press the Water button, Place your cup under the water

outlet, and then push gently against the dispenser pad.

Make sure the glass is in line with

the dispenser to prevent the water from splashing out.

To get cooler water :

The dispensed water is cool, not icy cold. When you want colder water with ice, dispense

ice into your glass first before filling it with water

to prevent water from splashing out.

Using the ice Dispenser

Press the ice button to select the type of ice you want.

Place your cup under the ice outlet, and then push gently against the dispenser pad.

Make sure the glass is in line with the dispenser to prevent the ice from bouncing out.

if you select Cubed ice after using the Crushed ice feature, a small amount of residual crushed ice

might be produced,

Ice-Maker Cover

Ice Chute Ice Bucket

A WARNING

• Do not put your fingers, hands, or any unsuitable objects in the chute or ice-maker

bucket.

This can cause personal injury or material damage,

Use only the ice maker provided with the refrigerator.

The water line to this refrigerator must be

installed / connected by a suitably qualified person and must be connected to a potable

water supply. The ice maker requires water pressure of

20 - 125 psi (138-862 kPa) to operate properly,

CAUTION

if you are going on a long vacation or business

trip and won't be using the water or ice dispensers for that period of time, close the

water valve to prevent leaks,

• if you have not used the ice maker for a

while, or you have opened the Freezer door frequently, the ice may stick together.

if this occurs, empty the ice bucket or break up

the ice with a wood kitchen tool.

Do not use sharp items such as knives or forks,

• When you remove the ice bucket, there may

still be some residual ice in the ice maker, The ice maker may eject this ice into the

freezer,

Engl sh --28

STORING FOOD

The Samsung Side-By-Side Refrigerator has been designed to provide you with maximum space saving features and functions.

Here are some of the customized compartments we have created to keep your food fresher, longer. Remember, to prevent odors from penetrating the ice in the freezer, wrap stored food as securely and as airtight as possible.

CAUTION

Because the following operating instructions cover various models, your refrigerator may differ slightly from those described in this manual.

(1)--

(2)

(3) --

(4)

Lamp Cover

Water Filter

--(5) (6)

(7)

(8)

Foldable Shelf

(9)

(10)

-- (11)

(12)

Engl sh --29

Storing food in the freezer

Designed to store lots of ice easily.

/_ WARNING

Do not put your fingers, hands or any other objects in the ice chute or the ice maker bucket. Doing so can cause personal injury or material

damage

Can be used to store all types of frozen food.

Can be used for small packages of frozen food.

Best used to store meats or dry foods.

Stored food should be wrapped securely using foil or other suitable wrapping materials or

containers.

Storing food in the fddge

Designed to be crack-resistant.

They can be used to store all types of food and drinks.

Circular marks on the glass surface are a normal phenomenon and can usually be wiped clean

with a damp cloth.

Best place to keep eggs. Place the egg tray on a shelf for easy access.

Helps to preserve the taste of food and prolongs

its freshness. Use to store bread and cake.

Designed to handle large, bulky items such as gallons of milk or other large bottles and containers.

Used to preserve the freshness of your stored vegetables and fruits.

Can be used to store smaller dairy items like butter or margarine, yogurt, or cream-cheese

bricks.

Can be used to store beverage cans or bottles.

Helps wine maintain its taste by providing an optimized place for storing your wine bottles.

Bottles should be stored tightly together

so that they do not tip and fall out when

the refrigerator door is opened.

A WARNING

• Ifyou plan to go away for a significant time, empty the refrigerator and turn it off.

Wipe excess moisture from the inside of the

refrigerator and leave the doors open. This helps keep odor and mold from developing.

• Ifyou do not intend to use the refrigerator for a long period of time, pull out the power plug.

Deteriorating power cord insulation may cause

a fire.

Engl sh- 30

+ 86 hidden pages