Samsung QND-6070R User Manual

NETWORK CAMERA

User Manual

QND-6070R/QNO-6070R/QNV-6070R

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated

from 12 Vdc, min. current for each product.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products.

The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

4_ overview

CONTENTS

overview

installation & connection

network connection and

setup

3 Important Safety Instructions 6 Product Features 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs 7 What’s Included 8 At a Glance (QND-6070R) 10 At a Glance (QNO-6070R) 11 At a Glance (QNV-6070R)

13 Installation (QND-6070R) 14 Installation (QNO-6070R) 15 Installation (QNV-6070R) 18 Inserting/Removing a Micro SD Memory

Card

20 Memory Card Information (Not Included) 20 Connecting with other Device

24 Connecting the Camera Directly to Local

Area Networking

24 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

25 Connecting the Camera Directly to a

PPPoE Modem

25 Connecting the Camera to a Broadband

Router with the PPPoE/Cable Modem

26 Buttons used in IP Installer 26 Static IP Setup 28 Dynamic IP Setup 28 Port Range Forward (Port Mapping) Setup 29 Connecting to the Camera from a Shared

Local PC

29 Connecting to the Camera from a Remote

PC via the Internet

web viewer

setup screen

appendix

30 Connecting to the Camera 31 Password setting 31 Login 31 Plug-in support specifications for each

browser

32 Installing WebViewer Plugin 32 Using a Plug-in Free Webviewer 32 Using the Live Screen (Plug-in Free

Webviewer)

33 Using the Live Screen (Plug-in Webviewer) 35 Playing the recorded video (Plug-in Free

Webviewer)

37 Playing the recorded video (Plug-in

Webviewer)

40 Setup 40 Basic Setup 44 Audio & Video setup 49 Network Setup 52 Event Setup 54 NAS (Network Attached Storage) guide 59 System Setup

61 Specification 63 Product Overview 64 Troubleshooting 65 Open Source Announcement

●● OVERVIEW

English _5

overview

PRODUCT FEATURES

• Dustproof/Waterproof (IP66) (QNO-6070R/QNV-6070R)

The dustproof and waterproof design makes you feel at ease when installing the product outdoors or exposing it to rain.

• IR mode

If the IR indicator turns on, the product switches to the IR mode for preventing an object from being too bright, which helps you identify the object in near distance.

• Supports 2 megapixel resolution videos

• Multi-Streaming

This network camera can display videos in different resolutions and qualities simultaneously using different CODECs.

• Web Browser-based Monitoring

Using the Internet web browser to display the image in a local network environment.

• Alarm

When an event occurs, video is either sent to the email address registered by the user, sent to the FTP server, saved in a Micro SD card or NAS, or a signal is sent to the alert output terminal.

• Tampering Detection

Detects tempering attempts on video monitoring.

• Defocus detection function

Detects the defocus phenomenon of the camera lens.

• Motion Detection

Detects motion from the camera’s video input.

• Auto Detection of Disconnected Network

Detects network disconnection before triggering an event.

• ONVIF Compliance

This product supports ONVIF Profile S&G. For more information, refer to www.onvif.org.

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• Supported OS : Windows 7, 8.1, 10, Mac OS X 10.9, 10.10, 10.11

• Plug-in free web viewer

Supported web browsers : Google Chrome 47, MS Edge 20

• Plug-in Webviewer

Supported web browsers : MS Explorer 11, Mozilla Firefox 43, Apple Safari 9 ※ Mac OS X only

• VGA : PCIe 256MB GDDR3 video graphics card or higher

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 4GB ~ 128GB (uhs-1 class)

• For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

Recommended products Available sizes

Netgear NAS A maximum of 16 cameras can access simultaneously.

Synology NAS A maximum of 16 cameras can access simultaneously.

When you use Netgear’s NAS equipment, do not allocate the capacity for use.

If you use NAS equipment for purposes other than video saving, the number of accessible cameras may be reduced.

6_ overview

WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description Model Name

QND-6070R

Appearance Item Name Quantity Description Model Name

Tapping Screw

Used for installation on the wall or

ceiling

QND-6070R

QNO-6070R/

QNV-6070R

●● OVERVIEW

Camera

Instruction book, Installer S/W CD

Quick Guide

(Optional)

Warranty card

(Optional)

Template

Product installation guide

QNO-6070R

QNV-6070R

QND-6070R/ QNO-6070R/

QNV-6070R

QND-6070R/ QNO-6070R/

QNV-6070R

QND-6070R/ QNO-6070R/

QNV-6070R

QND-6070R/ QNO-6070R/

QNV-6070R

Power Terminal Block

L Wrench

Card-type moisture absorbent

Alarm cable

RJ45 waterproof accessory

Sunshield

Plugged in the power plug

Used to control the direction of the

camera / Used to remove and replace

the dome cover

Attached when installed.

Used when connecting to an alarm QND-6070R

Used to install in humid places QNO-6070R

It protects the camera from the direct

sunlight.

QND-6070R/

QNV-6070R

QNO-6070R/

QNV-6070R

QNO-6070R

QNV-6070R

QNO-6070R

English _7

overview

Appearance Item Name Quantity Description Model Name

Sunshield Hold

Machine Screws

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Power Cable

Audio/alarm cable

Cable bush

It fixes the sunshield with the camera. QNO-6070R

Used for assembling the dome case

when installing the product on the

pipe, wall mount, etc. or blocking a

Used to plug into the power port QNV-6070R

Used to connect with the audio and

Used to connect the LAN cable with a

hole.

alarm port

diameter of Ø7~8.5.

QNV-6070R

AT A GLANCE (QND-6070R)

Appearance

Item Description

Dome cover

Camera Case

Microphone hole

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

Microphone is embedded.

8_ overview

Components

l k

ij gh

Item Description

NETWORK

ACT

LiNK

Inside cover Protective cover for the main body.

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

Power Port Port for power terminal block.

Microphone hole Microphone is embedded.

Network Port Used to connect the PoE or Ethernet cable for network connection.

Micro SD Memory Card

Compartment

Reset Button

Alarm I/O Port

Zoom control lever

Focus control lever

Compartment for the Micro SD memory card.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

ARM-IN Used to connect the alarm input sensor or external day/night sensor.

ARM-OUT Used to connect the alarm output signal.

GND These are common ports to connect alarm input/output signals.

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

●● OVERVIEW

English _9

overview

AT A GLANCE (QNO-6070R)

Appearance

b ca

Item Description

Micro SD card slot

Reset button

Sunshield Hold

(Internal space of the product) This is a slot in which you can insert a Micro SD card.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

It fixes the sunshield with the camera.

e f

If you reset the camera, the network settings will be adjusted so that DHCP can be enabled. If there is no DHCP server in the network, you must run the IP Installer program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

Components

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

b c

Item Description

Power Port Used to plug the power cable.

ARM-OUT Used to connect the alarm output signal.

Alarm I/O Port

Network Port Used to connect the PoE or Ethernet cable for network connection.

Audio In Jack Used to connect to a microphone.

GND These are common ports to connect alarm input/output signals.

ARM-IN Used to connect the alarm input sensor or external day/night sensor.

Sunshield

Focus control lever

Zoom control lever

10_ overview

It protects the camera from the direct sunlight.

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

AT A GLANCE (QNV-6070R)

Components

Appearance

Dome cover

Camera Case

Item Description

Case cover used to protect the lens and the main unit.

Housing part that covers the camera body.

j i

bca

●● OVERVIEW

DC12V

FRONT

RESET

12345

ALM IN/OUT

AUDIO IN

d e

RESET

ACT

NETWORK

LINK

English _11

overview

Illumination Sensor Detects incoming light to control the IR LED.

Lens Lens for the camera.

IR LED These infrared LED’s are controlled by the illumination sensor.

Reset button

Audio and alarm cable port

Power Port Port for power terminal block.

Network Port Used to connect the PoE or Ethernet cable for network connection.

Micro SD Memory Card

Compartment

Zoom control lever

Focus control lever

Item Description

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Terminal to which the audio and alarm cable is connected in order to connect with an external alarm device/microphone.

Compartment for the Micro SD memory card.

T Zoom in (Tele)

W Zoom out (Wide)

Release the lever and move it to left or right to zoom the lens in or out. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

N Focusing on a near object (Near)

F Focusing on a far object (Far)

Release the lever and move it to left or right to adjust the lens focus. Turn the lever clockwise to fix the adjusted position to prevent it from being moved.

12_ overview

installation & connection

INSTALLATION (QND-6070R)

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Disassembling

1. Use one hand to hold the camera’s bottom part and turn the cover

counterclockwise with another hand to separate it.

2. Lift up the inner cover to separate it.

LiNK

NETWORK

ACT

LiNK

NETWORK

ACT

Dome Cover

Installation

1. Attach the installation template to the selected area and punch 3

holes as shown in the figure.

2. Using 2 tapping screws provided, fix the camera at 2 holes drilled

with a template.

Set the < > mark imprinted on the camera to face the direction of camera

monitoring.

3. Connect the camera internal terminal with the corresponding

cable.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 18)

We recommend you not to touch the lens as the camera lens has been

properly focused in the final process of manufacturing. If so, the lens may be out of focus or stained by alien substances.

5. Please connect the inner cover to the main body.

6. While grabbing the bottom side of the camera with your hand, please

grab and push its cover with the other hand to align the two arrow signs, as shown in the figure.

To assemble the dome cover, make the arrows match each other and press the

cover firmly. If the dome cover is rotated during assembly or is assembled incorrectly, diffused reflection may occur or the lens section may rotate, which will cause the shooting range to be changed.

Make sure that the dome cover is correctly connected to the bottom part as shown

in the figure. If the snap-fit is not connected correctly, the dome cover may fall, which may cause injury.

●● INSTALLATION & CONNECTION

LiNK

ACT

NETWORK

LiNK

ACT

NETWORK

English _13

installation & connection

INSTALLATION (QNO-6070R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Installation

1. Attach the installation template at a desired location and make 3

holes the same size as shown in the picture below.

2. Insert and fasten 3 tapping screws provided into 3 holes to secure

the camera.

3. Connect the appropriate cables with camera terminals.

4. Adjust the camera direction using the L wrench provided.

When you adjust the camera position using a bracket, please loosen the

bracket screw, adjust the camera, and tighten it. If you attempt to adjust it forcibly while the screw is tight, it may result in a scratch or other problems.

Mounting Template

Cable Line

How to connect the RJ45 waterproof cable to a LAN cable

1. Insert it through the arrow direction.

2. Connect the LAN connector (male) to the cable.

3. Connect the RJ45 modular jack (female) to the RJ45 connector

(male).

Please, keep each of the parts separated.

4. Assemble by rotating the RJ45 modular jack (female) and the RJ45

protection cover clockwise (Follow the arrow).

5. Assemble by rotating RJ45 protection cover and back cover

clockwise (Follow the arrow). When the back cover is assembled, the cable waterproof gasket is tightly attached to the cable to make it waterproof.

You must fully assemble it to rotate the back cover up to the end of the screw

thread of the RJ45 connector.

RJ45 modular

jack (female)

RJ45 connector (male)

Rubber ring

RJ45 connector protection cover

Back cover

Rubber ring

Cable waterproof

gasket

14_ installation & connection

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, AUDIO, and LAN cables.

Camera

System

2. Wrap the black cable jacket (Area A) and the cable connection

area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause

leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

Camera

System

To adjust the zoom factor or focus

1. Loosen the front cover as shown.

2. Loosen the zoom/focus lever slightly.

3. Position the zoom/focus lever to WIDE (NEAR) or TELE (FAR) as appropriate.

4. Then, tighten the zoom/focus lever to fix the adjusted position.

5. Turn the front cover to tighten it.

INSTALLATION (QNV-6070R)

This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• It must be installed on the area (ceiling or wall) that can withstand 5 times the weight of the camera including the installation bracket.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

Disassembling

DC12V

FRONT

Dome cover

1. Using the L wrench provided, turn the 3 fastening bolts

on the dome cover counter clockwise to remove the cover.

Bolts

Camera Body

●● INSTALLATION & CONNECTION

RESET

12345

ALM IN/OUT

AUDIO IN

Front cover

Zoom Lever

↔

WIDE

TELE

Focus Lever

↔

FAR

NEAR

To ensure seamless waterproofing, tighten up the front cover by turning it to the end.

When combining the front cover, please combine the main body and the front cover so that the LOCK indicator is interlocked.

Use the lever to adjust the zoom factor or focus, and turn the lever clockwise to fix it.

Before you can adjust the zoom factor/focus of the lens, loosen and remove the front cover.

Camera Case

English _15

installation & connection

Installation

1. Using the template provided as an accessory, drill holes for

installation screws (at least 55mm deep with a diameter of 6mm).

2. Align the installation holes of the camera, and then insert and

fasten tapping screws (M4.5 x L50).

3. Connect and arrange the necessary cables lest that they should

be damaged or twisted while installing the camera.

4. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 18)

5. Close the dome cover.

`Securely fasten the fastening bolt using an L wrench to prevent water from

leaking.

Connecting the LAN cable

1. Remove the dome cover and the case.

2. Pull out the long projected part of the rubber plug on the bottom and

remove it as shown in the figure.

Use an appropriate cable bush for the LAN cable to be connected.

- Basic camera : Use the cable with a diameter of Ø5~6.5.

- Components provided : Use the cable with a diameter of Ø7~8.5.

3. Insert the LAN cable into the large hole made by removing the projected part of the rubber plug in step 2 above.

4. Remove the sheath with a cable cutter, and align the cables.

5. Connect the LAN cable with a LAN connector, and insert it into the LAN

tool.

6. Connect the finished cable to the Ethernet port.

Connecting the audio/alarm cable and power cable

1. Remove the dome cover and the case.

AUDIO IN

ALM IN/OUT

12345

RESET

FRONT

DC12V

ACT

LINK

NETWORK

ACT

LINK

NETWORK

2. Pull out the rubber plug on the bottom as shown in the figure.

3. Insert the alarm/audio cable through the hole created by removing the

rubber cap in No. 2, and connect the cable to the alarm terminal.

4. When installing the camera, arrange the cables by hanging them up on

the fixing hook to prevent the cables from being damaged or caught.

5. Put the rubber cap located on the alarm/audio cable in the hole.

6. Insert the power cable through the small hole and hang the cable

up on the fixing hook.

7. Connect the power cable to the power terminal block.

8. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section.

(page 18)

9. Attach the dome cover.

RESET

NETWORK

ACT

LINK

ACT

LINK

16_ installation & connection

CAUTION: Be w are of the

Rated Voltage and Po larit y

of the power connec tion.

Attaching to the unbundled adapter

Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience.

1. Remove the dome cover from the case by referring to the “Disassembling” section. (page

)

2. Use the provided machine screw to fix the camera case to the unbundled adapter.

3. Connect and arrange the necessary cables lest that they should be damaged or twisted while installing the

camera.

4. Install the camera body in the reverse order of “Disassembling”.

5. Adjust the lens in a desired direction by referring to the “Adjusting the monitoring direction for the camera” section. (page 18)

6. Close the dome cover.

`Securely fasten the fastening bolt using an L wrench to prevent water from leaking.

Outdoor installation

1. Connect the power, I/O, BNC, and LAN cables.

Camera

System

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.

If the cable jacket is not waterproofed properly, then it can directly cause

leakage. Make sure to protect the cable with a dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice

Camera

System

its normal length.

Optional Accessories for Installation

For your easier installation, you can purchase appropriate optional accessories available.

1. WALL MOUNT ADAPTOR(SBP-300WM or SBP-300WM1)/ HANGING MOUNT(QND-6070R : SBP-122HM, QNV-6070R : SBP-301HM2) This adaptor is used when installing the dome camera onto a wall.

2. CEILING MOUNT ADAPTOR(SBP-300CM)/HANGING MOUNT(QND-

6070R : SBP-122HM, QNV-6070R : SBP-301HM2) This adaptor is used when installing the dome camera on a concrete ceiling.

●● INSTALLATION & CONNECTION

3. POLE MOUNT ADAPTOR(SBP-300PM)

This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP300WM1) installation on a pole whose diameter is bigger than 80mm.

4. CORNER MOUNT ADAPTOR (SBP-300KM)

This is an adaptor for WALL MOUNT ADAPTOR (SBP-300WM or SBP-300WM1) installation on the corner of wall joint.

5. BULLET BACK BOX (SBO-100B1)

Adapter used for the installation of a bullet camera on the wall or ceiling.

English _17

installation & connection

6. VANDAL BACK BOX (SBV-136B) Adapter used for the installation of a vandal camera on the wall or ceiling.

Adjusting the monitoring direction for the camera (QND-6070R/QNV-6070R)

Pan

LiNK

ACT

NETWORK

Tilt

Lens rotation

`Adjusting the monitoring direction

You can adjust the camera direction only when the camera is fixed on the ceiling. Where, rotating the camera unit to the left or right is called Pan, adjusting the tilt is called Tilt, and turning the lens on its axis is called Rotation.

- The effective range of pan is a total of 350 degrees.

- The effective range of rotation is a total of 355 degrees.

- The effective range of tilt is a total of 67 degrees.

The image can be covered up by the camera case depending on the angle.

Do not forcefully turn the focus/zoom lens after the dome case is disassembled.

Otherwise, it may cause an incorrect focus due to a motor failure.

INSERTING/REMOVING A MICRO SD MEMORY CARD

Disconnect the power cable from the camera before inserting the Micro SD memory card.

Do not insert the Micro SD memory card while it’s upside down by force.

Otherwise, it may damage the Micro SD memory card.

When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.

Disassembly of the product cover should be finished within 5 minutes, or there will be the risk of internal dew condensation.

Inserting a Micro SD Memory Card (QNO-6070R)

1. Turn the front cover to the UNLOCK [ ] direction.

2. Pull and separate the front cover.

3. Insert a Micro SD card in the arrow direction shown in the figure.

`Methods of adjustment

1. After installing the camera, adjust the panning angle in consideration of the monitoring direction.

2. Set the horizontal angle so that the image is not reversed.

3. Adjust the tilt angle so that the camera faces toward the monitoring object.

18_ installation & connection

Inserting a Micro SD Memory Card (QND-6070R/QNV-6070R)

NETWORK

LINK

ACT

NETWORK

LINK

ACT

1. Separate the Dome cover of the camera.

2. Insert a Micro SD card in the arrow direction shown in the figure.

<QND-6070R>

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

●● INSTALLATION & CONNECTION

<QND-6070R>

RESET

<QNV-6070R>

ACT

NETWORK

LINK

<QNO-6070R>

RESET

ACT

NETWORK

LINK

<QNV-6070R>

English _19

installation & connection

Pressing too hard on the Micro SD memory card can cause the card to shoot out uncontrollably from the slot when released.

Before removing your Micro SD memory card, turn off the camera or go to <Storage>, turn the device off, and press the [Apply

(

)] button. (Page 53)

If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or

damaged.

MEMORY CARD INFORMATION (NOT INCLUDED)

What is a memory card?

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Selecting a memory card that’s suitable for you

Your camera supports Micro SD/SDHC/SDXC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card.

For your camera, we recommend you use a memory card from the following manufacturers: Micro SD/SDHC/SDXC Memory Card : Sandisk, Transcend

It is recommended to use a 4 to 128GB (uhs-1 class) memory card for this camera.

Playback performance can be affected depending on the speed of memory card, so use the high-speed memory card.

CONNECTING WITH OTHER DEVICE

NETWORK

ACT

LiNK

Ethernet

<QND-6070R>

Power

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

Power

Memory Card Components

Contacts

Micro SD/SDHC/SDXC

20_ installation & connection

Ethernet

<QNO-6070R>

Power

Ethernet

RESET

<QNV-6070R>

CAUTION: Be ware o f the

Rated Voltage and P olari ty

of the power conne ction .

NETWORK

ACT

LINK

Ethernet Connection

Connect the Ethernet cable to the local network or to the Internet.

Power Supply

Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.

If both PoE and DC 12V are applied simultaneously, the product will be supplied with power from PoE.

- You can also use a router featuring PoE to supply power to the camera.

- Use PoE that is compliant with the IEEE 802.3af protocols.

- It is advisable to use only one power source from PoE and DC 12V.

Be careful not to reverse the polarity when you connect the power cable.

If you want to connect an external device, you must turn off the external device before proceeding.

Power Cable Specification for Each Model

In case of DC 12V Input:

Wire Type (AWG) #22 #20 #18

Cable Length (Max.) 24m 38m 60m

Network Cable Specification

Item Contents Remark

Connector RJ45

Ethernet 10/100BASE-T 10/100 Mbps

Cable UTP Category 5e

Max Distance 100M DC Resistance ≤ 0.188 Ω/m

PoE Support IEEE 802.3af

If you use a cable other than Category 5e standards, 100m of transmission distance is not guaranteed.

Connecting to Audio Input

Speaker

Microphone

Network

Microphone

Amp

Microphone

Amp

Microphone

1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the

microphone is connected to.

You can use the built-in microphone in the camera without connecting an external microphone.

(only available in QND-6070R)

2. Check the specifications for audio input.

• Audio Codec

- Audio In : G.711 PCM (Bit Rate: 64kbps / Sampling Frequency: 8kHz), G.726 ADPCM (Bit Rate: 16Kbps, 24Kbps, 32Kbps, 40Kbps / Sampling Frequency: 8kHz)

• Full duplex Audio

• Audio in (QND-6070R) : Selectable (Built-in microphone), Supported voltage: 2.5VDC (4mA), Input

impedance: 2K Ohm

• Audio in (QND-6070R/QNV-6070R) : Selectable (microphone/Line-in), Supported voltage: 2.5VDC (4mA),

Input impedance: 2K Ohm

●● INSTALLATION & CONNECTION

English _21

installation & connection

Connecting to the I/O port box

Connect the Alarm I/O cable to the corresponding port of the port box.

Sensor Alarm

(Warning lamp)

DC12V

FRONT

RESET

12345

ALM IN/OUT

AUDIO IN

Sensor Alarm

(Warning lamp)

<QNV-6070R>

• ALARM-IN : Used to connect the alarm input sensor or external day/night sensor.

• ALARM-OUT : Used to connect the alarm output signal.

<QND-6070R>

CAUTION:Be ware of the

Rated Voltage and Polarity of the power connection.

• GND : Common port for alarm in/output signal.

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open

collector method, it may cause malfunction. Refer to the “Alarm Out Wiring Diagram” when connecting devices that exceed the voltage and current specifications. (page

23)

To connect the external sensor

Connect one strand of each signal line (2-strand) of the sensors to the [ALARM IN] port, and connect the other strand to the [GND] port.

SensorAlarm

<QNO-6070R>

22_ installation & connection

Alarm In Wiring Diagram

External

connection

Inside of the camera

VCC_3.3V

RESISTOR RESISTOR

Sensor

RESISTORALARM IN (5mA SINK)

MLCC

GND

DIODE

TRANSISTOR

GND

To connect the alarm out

If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction.

Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications.

Alarm Out Wiring Diagram

Warning lamp /

Siren power

(-) (+)

Warning lamp /

Siren

External connection Inside of the camera

DC 5V or 3.3V

DIODE

RELAY

RESISTOR 10K ohm

TRANSISTOR

GND

ALARM OUT (12VDC 20mA MAX)

RESISTOR

TRANSISTOR

GND

●● INSTALLATION & CONNECTION

English _23

+ 53 hidden pages