PDP-TELEVISION
(PLASMA DISPLAY PANEL)
PS42Q91HD
PS50Q91HD
PS42C91HD
PS50C91HD
Owner’s Instructions
Before operating the unit, please read this manual thoroughly,
and retain it for future reference.
ON-SCREEN MENUS
PC DISPLAY
PICTURE IN PICTURE (PIP)
TELETEXT
SRS TruSurround XT
Digital Natural Image engine
Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Screen Image retention
Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention.
This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Height
The PDP can normally operate only under 2000m in height. It might abnormally function at a place over 2000m in height so do not install and operate there.
Heat on the top of the PDP TV
The top side of the product may be hot after long period of use as heat dissipates from the panel through the vent hole in the upper part of the product. This is normal and does not indicate any defect or operation failure of the product. However, children should be prevented from touching the upper part of the product.
The product is making a ‘cracking’ noise.
A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding environment such as temperature or humidity. This is normal and not a defect of the unit.
Cell Defects
The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require sophisticated technology to produce. However, there may be few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
Avoid operating the TV at temperatures below 5°C(41°F)
A still image displayed too long may cause permanent damage to the PDP Panel.
Watching the PDP TV in 4:3 format for a long period of time may leave tracesn of borders displayed on the left, right and centre of the screen caused by the difference of
light emission on the screen. Playing a DVD or a game console may cause similar effect
to the screen. Damages caused by the above effect are not covered by the Warranty.
Afterimage on the Screen.
Displaying still images from Video games and PC for longer than a certain period of time may produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
Warranty
-Warranty does not cover any damage caused by image retention.
-Burn-in is not covered by the warranty.
Installation
Be sure to contact an authorized service centre, when installing your set in a location with heavy dust, high or low temperatures, high humidity, chemical substance and where it operates continually such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.
© 2007 Samsung Electronics Co., Ltd. All rights reserved.
Contents |
|
Connecting and Preparing Your TV |
|
List of Parts........................................................ |
3 |
Viewing the Control Panel................................. |
5 |
Viewing the Connection Panel........................... |
5 |
Viewing the Remote Control |
|
(PS42Q91HD,PS50Q91HD)............................. |
7 |
Viewing the Remote Control |
|
(PS42C91HD,PS50C91HD).............................. |
8 |
Installing Batteries in the Remote Control......... |
9 |
Switching On and Off......................................... |
9 |
Placing Your Television in Standby Mode.......... |
9 |
Plug & Play...................................................... |
10 |
Setting the Channels |
|
Storing Channels Automatically....................... |
11 |
Storing Channels Manually.............................. |
12 |
Setting the Channel Manager.......................... |
13 |
Activating the Child Lock................................. |
13 |
Sorting the Stored Channels........................... |
14 |
Assigning Channels Names............................ |
14 |
Fine Tuning Channel Reception...................... |
15 |
LNA(Low NoiseAmplifier)................................ |
15 |
Setting the Picture |
|
Changing the Picture Standard....................... |
16 |
Adjusting the Custom Picture.......................... |
16 |
Changing the Colour Tone............................... |
17 |
Configuring Detailed Settings on the Picture... |
18 |
Changing the Picture Size............................... |
19 |
Freezing the Current Picture........................... |
19 |
Digital NR /Active Colour / DNIe / |
|
Movie Plus ...................................................... |
20 |
Resetting the Picture Settings to the Factory |
|
Defaults........................................................... |
21 |
Viewing the Picture In Picture (PIP)................ |
21 |
Screen burn Protection.................................... |
22 |
Setting the Sound |
|
Changing the Sound Standard........................ |
23 |
Adjusting the Sound Settings.......................... |
23 |
Setting the TruSurround XT (SRS TSXT)........ |
24 |
Adjusting the Volume Automatically................. |
24 |
Selecting the Internal Mute.............................. |
25 |
Listening to the Sound of the Sub Picture....... |
25 |
Resetting the Sound Settings to the Factory |
|
Defaults........................................................... |
26 |
Connecting Headphones................................. |
|
Selecting the Sound Mode. |
|
Setting the Time |
|
Setting and Displaying the Current Time......... |
27 |
Selecting the Sleep Timer................................ |
27 |
Switching the Television On and Off |
|
Automatically................................................... |
28 |
Function Description |
|
Using Game Mode........................................... |
29 |
Setting the Blue Screen Mode / |
|
Selecting the Melody ...................................... |
29 |
Setting the Home Theatre PC........................ |
30 |
Setting the Light Effect.................................... |
30 |
Using the Energy Saving Feature.................... |
31 |
HDMI Black Level............................................ |
31 |
USING The DTV FeATuRe |
|
Previewing the DTV Menu System.................. |
32 |
Updating the Channel List Automatically......... |
33 |
Updating the Channel List Manually................ |
33 |
Editing Your Favourite Channels..................... |
34 |
Selecting Channel List..................................... |
36 |
Displaying Programme Information................. |
36 |
Viewing the EPG |
|
(Electronic Programme Guide) Information..... |
37 |
Using the Scheduled List................................. |
38 |
Setting the Default Guide................................ |
38 |
Viewing All Channels and |
|
Favourite Channels......................................... |
39 |
Selecting the Time Zone.................................. |
39 |
Adjusting the Menu Translucency.................... |
40 |
Setting up the Parental Lock........................... |
40 |
Setting the Subtitle.......................................... |
41 |
Selecting the Audio Format............................. |
41 |
Viewing Product Information............................ |
41 |
Checking the Signal Information...................... |
42 |
Upgrading the Software................................... |
42 |
Resetting......................................................... |
44 |
Selecting the Preferred Language |
|
(Subtitle , Audio).................................................. |
44 |
English -
Using the Teletext Feature |
|
Selecting the Source....................................... |
45 |
Editing the Input Source Names...................... |
45 |
Teletext Decoder.............................................. |
46 |
Displaying the Teletext Information.................. |
46 |
Selecting a Specific Teletext Page.................. |
47 |
Using Fastext to Select a Teletext Page.......... |
47 |
Setting Up Your Remote Control..................... |
48 |
Remote Control Codes.................................... |
50 |
Setting the PC |
|
Setting up Your PC Software |
|
(Based on Windows XP).................................. |
53 |
Display Modes................................................. |
53 |
Setting the PC................................................. |
54 |
Wall-Mount Adjustment (Sold separately)........ |
55 |
About Anynet+ |
|
What is Anynet+? ........................................... |
56 |
Connecting Anynet+ Devices.......................... |
56 |
Setting Up Anynet+.......................................... |
57 |
Scanning and Switching between Anynet+ |
|
Devices............................................................ |
58 |
Recording........................................................ |
59 |
Listening through a Receiver........................... |
60 |
Check Points before Requesting Service........ |
61 |
Recommendations For Use |
|
Troubleshooting: |
|
Before Contacting Service Personnel.............. |
62 |
Technical and Environmental Specifications .. |
63 |
Stand Swivel (Left / Right)............................... |
63 |
Symbol |
Press |
Important |
Note |
Button
English -
Owner’s Instructions |
Remote Control/ |
Power Cord |
Cloth-Clean |
|
AAA Batteries |
|
|
Warranty Card/ |
Cover-Bottom / Screws |
Ferrite Core for |
Registration Card/ |
(2ea) |
Power Cord |
Safety Guide Manual |
(Refer to page 62) |
|
Sold Separately
S-Video Cable |
Antenna Cable |
Component Cables |
HDMI/DVI Cable |
|
|
(RCA) |
|
PC Cable |
PC Audio Cable |
HDMI Cable |
Ferrite Core (Power Cord)
The ferrite core is used to shield the cable from interference. When connecting a cable, open the ferrite core and clip it around the cable.
English -
The product colour and shape may vary depending on the model.
Speaker |
SOURCE
Displays a menu of all of the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2, HDMI3 and DTV).
HDMI3 mode is available only in PS42Q91HD/ PS50Q91HD.
MENU
Press to see an on-screen menu of your TV’s features.
+ VOL -
Press to increase or decrease the volume. In the on-screen menu, use the + VOL - buttons as you use the + and - buttons on the remote control.
CH
Press to change channels.
In the on-screen menu, use the CH
buttons as you use the
and
buttons on the remote control.
(ENTER)
(POWER)
Press to confirm a selection. Press to turn the TV on and off.
Power Indicator
-Power Off: Blue
-Power On: Off
Remote Control Sensor
Aim the remote control towards this spot on
the TV.
English -
Power Input
Whenever you connect an external device to your TV, make sure that power on the unit is turned off.
When connecting an external device, match the colour of the connection terminal to the cable.
Connecting External A/V Devices (AV IN 1)
-Connect RCA cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
-Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio out connectors on the A/V device.
Connecting AUDIO
-Connect RCA audio cables to “R - AUDIO - L” on the rear of your set and the other ends to corresponding audio in connectors on the Amplifier or DVD Home Theatre .
-HDMI3 mode is available only in PS42Q91HD/PS50Q91HD.
Connecting HDMI IN 1, HDMI IN 2, HDMI IN 3
-Supports connections between HDMI-connection-enabled AV devices (Set-Top Boxes, DVD players)
-No additional Audio connection is needed for an HDMI to HDMI connection.
What is HDMI?
-"High Definition Multimedia interface" allows the transmission of high definition digital video data and multiple channels of digital audio (5. 1 channels).
-The HDMI/DVI terminal supports DVI connection to an extended device with the appropriate cable (not supplied). The difference between HDMI and DVI is that the HDMI device is smaller in size, has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed, and supports multi - channel digital audio.
English -
Connecting DVI IN(HDMI 2)(AUDIO R/L)
-When connecting this product via HDMI or DVI to a Set Top Box, DVD Player or Games Console etc, make sure that it has been set to a compatible video output mode as shown in the table below. Failure to observe this may result in picture distortion, image breakup or no picture.
-When using an HDMI/DVI cable connection, it is only possible from the HDMI 2 IN terminal.
You should use the DVI-to-HDMI cable or DVI-HDMI Adapter for the connection, and the “R - AUDIO - L” terminal on DVI for sound output.
Supported modes for HDMI/DVI and Component
|
480i |
480p |
576i |
576p |
720p |
1080i |
HDMI/DVI 50Hz |
X |
X |
X |
O |
O |
O |
HDMI/DVI 60Hz |
X |
O |
X |
X |
O |
O |
Component |
O |
O |
O |
O |
O |
O |
- Do not attempt to connect the HDMI/DVI connector to a PC or Laptop Graphics Card. (This will result in a blank screen being displayed)
Connecting an Aerial or Cable Television Network
To view television channels correctly, a signal must be received by the set from one of the following sources:
- An outdoor aerial / A cable television network / A satellite network
Connecting External A/V Devices
-Connect RCA or S-VIDEO cable to an appropriate external A/V device such as VCR, DVD or Camcorder.
-Connect RCA audio cables to "R - AUDIO - L" on the rear of your set and the other ends to corre sponding audio out connectors on the A/V device.
-Headphone may be connected to the headphone output ( ) on the rear of your set. While the head phone is connected, the sound from the built-in speakers will be disabled.
Connecting Computer
-Connect the D- Sub cable (optional) to "PC (PC IN)" on the rear of your set and the other end to the Video Card of your computer.
-Connect the stereo audio cable (optional) to "AUDIO (PC IN)" on the rear of your set and the other end to "Audio Out" of the sound card on your computer.
DIGITAL AUDIO OUT (OPTICAL)
- Connect to a Digital Audio Component.
SERVICE2
- Service connection for qualified service engineer.
Connecting Component Devices (DVD)
-Connect component video cables (optional) to component connector ("Pr", "Pb", "Y") on the rear of your set and the other ends to corresponding component video out connectors on the DVD.
-Connect RCA audio cables (optional) to "R - AUDIO - L" on the rear of your set and the other ends to corresponding audio out connectors on the DVD.
-This PDP TV displays its optimum picture resolution in 720p mode.
-This PDP TV displays its maximum picture resolution in 1080i mode.
English -
Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)
(Refer to page 50-52) Television Standby button
Number buttons for direct channel access
One/Two-digit channel selection
It display "Channel List" on the screen.
Selects the TV and DTV mode directly
VCR/DVD Functions Rewind, Stop, Play/Pause, Fast/Forward
Volume increase
Volume decrease
Temporary sound switch-off
Menu display and change confirmation
Returns to the previous menu
Electronic Program Guide (EPG) display
Picture size selection
Sound effect selection
Adjusts 5 separate devices - TV, DVD, STB, CABLE or
VCR.
When pressing this button, a number of buttons on the remote control (e.g. Selects a target device, volume, channel buttons) light up for a few seconds and then turn off to save power. This function is to conveniently use the remote control at night or when dark.
Available source selection
Previous channel
DTV menu display
Records for Live Broadcasting
P: Next channel
P: Previous channel
Exit the OSD
Control the cursor in the menu
Use to see information on the current broadcast
Runs the Anynet view functions and sets up Anynet devices.
Colour buttons : Press to add or delete channels and to store
channels to the favorite channel list in the “Channel List” menu.
Picture-In-Picture On / Off
Digital subtitle display
Picture effect selection
Picture freeze
When your remote does not work, change the batteries and press the "RESET" button for 2-3 seconds before use.
Teletext Functions
Exit from the teletext display
Teletext index
Alternately select Teletext, Double, or Mix.
Teletext size selection
Teletext mode selection (LIST/FLOF)
Teletext sub page
P
: Teletext next page
P: Teletext previous page
Teletext cancel
Teletext reveal
Fastext topic selection
Teletext hold
Teletext store
The performance of the remote control may be affected by bright light.
This is a special remote control for the visually impaired, and has Braille points on the Power, Channel, STOP, PLAY/PAUSE and Volume buttons.
English -
This is a special remote control for the visually impaired persons, and has Braille points on the
Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.
The performance of the remote control may be affected by bright light.
POWER button
(turns the TV on and off)
Number buttons for direct channel access
One/Two-digit channel selection
Channel control button
Selects the TV and DTV mode directly
Volume increase
Volume decrease
Temporary sound switch-off
Displays the main on-screen menu
Returns to the previous menu
TruSurround XT mode button
Picture size selection
Electronic Program Guide (EPG) display
Sound mode selection
Remote control setup
Selects a target device to be controlled by the Samsung remote control (TV, DVD, STB, CABLE, VCR)
Press to backlight the VOL, CH, and the active source button (TV, DVD, CABLE, STB, VCR) on the remote.
Available source selection
Previous channel
DTV menu display
Selects the HDMI mode directly
VCR/DVD Function
(Rewind, Stop, Play/Pause,
Fast/Forward)
Next channel
Previous channel
Exit the on-screen menu
Control the cursor in the menu
Use to see information on the current broadcast
Picture-In-Picture On / Off
Picture effect selection
Digital subtitle display
Picture freeze
If your remote control is not functioning properly, take out the batteries and press the reset button for about 2~3 seconds.
Re-insert the batteries and try using the remote control again.
Teletext Functions
Exit from the teletext display
Teletext index
Fastext topic selection
Teletext size
Teletext mode selection (LIST/FLOF)
Teletext sub page
P
: Teletext next page
P: Teletext previous page
Teletext cancel
Teletext reveal
Teletext display/mix both teletext information and the normal broadcast
Teletext hold
Teletext store
English -
1. Lift the cover at the back of the remote control upward as shown in the figure.
2. Install two AAA size batteries.
Make sure to match the "+" and "–" ends of the batteries with the diagram inside the compartment.
3. Replace the cover.
Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV.
(Assuming typical TV usage, the batteries last for about one year.)
If the remote control doesn’t work, check the following:
1.Is the TV power on?
2.Are the plus and minus ends of the batteries reversed?
3.Are the batteries drained?
4. Is there a power outage, or is the power cord unplugged? 5. Is there a special fluorescent light or neon sign nearby?
The mains lead is attached to the rear of your set.
1.Plug the mains lead into an appropriate socket.
The standby indicator lights up on the front of the set. (Except the Light Effect is selected with OFF.(Refer to "Setting the Light Effect" on Page 30))
2.Press the button on the front of the set.
You also can press the POWER
button or the TV/DTV button on the remote control to turn the TV on.
The programme that you were watching last is reselected automatically.
3.Press the numeric button (0~9) or channel up/down (/
) button on the remote control or
CH
button on the right side of the set.
4.To switch your set off, press the POWER button again.
Your set can be placed in standby mode in order to reduce the power consumption. The standby mode can be useful when you wish to interrupt viewing temporarily (during a meal, for example).
1. Press the POWERbutton on the remote control.
The screen is turned off and a blue standby light appears on the front of your set.
(Except the Light Effect is selected with OFF.(Refer to "Setting the Light Effect" on Page 30))
2. To switch your set back on, simply press the POWER, numeric buttons (0~9), TV/DTV button or channel up/down (
/
) button again.
Do not leave your set in standby mode for long periods of time (when you are away on holiday, for example).
It is best to unplug the set from the mains and aerial.
English -
When the TV is initially powered on, several basic settings proceed automatically and subsequently. The following settings are available.
1.Press the POWER button on the remote control.
The message "Start Plug & Play" is displayed with "OK" selected.
Then press ENTER/OK button. The message "Select Home Mode When installing this TV at home" is displayed with "Shop" or "Home" selected.
Plug & Play
Start Plug & Play.
OK
Enter |
Exit |
2.Press the ◄ or ► buttons to select “Shop” or “Home”, then the ENTER/OK button.
We recommend setting the TV to Home mode for the best picture in your home envronment.
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home) mode, press the Volume button and then hold down the MENU button for five seconds on the side panel of the TV.
3.The message "Check antenna input." is displayed with "OK" selected. Press the ENTER/OK button.
Please check that the area cable is connected correctly.
4.The message "Some DTV functions may not be available. Digital Scan?"is displayed with "Yes" or "No" selected. Press ◄ or ► buttons to select .Then press ENTER/OK button.
Yes : First an ATV search is performed and then a DTV ch. auto search is performed. No : Only an ATV search is performed.
5.The "Auto Store" menu is displayed with the "Start" selected. Press the ENTER/OK button.
The channel search will start and end automatically.
The DTV channel scan menu appears and the DTV channel is automatically updated.
If the DTV channel is updated, the Source in the source list of the Input menu is automatically changed to DTV. After all the available channels are stored, the "Clock Set" menu appears. Press the ENTER/OK button at any time to interrupt the memorization process.
For detailed descriptions about DTV channel update, refer to page 33 of this manual. After all the available digital channels are stored, the screen to Clock Set is displayed depending on the country.
6.Press the ◄ or ► buttons to move to the "Month" , "Day" , "Year", "Hour", "Minute",
Set the "Month" , "Day" , "Year", "Hour", "Minute", or by pressing the ▲ or ▼ button.
You can also set the hour and minute by pressing the number buttons on the remote control. When you have finished, press the ENTER/OK button.
The message “Enjoy your viewing.” is displayed.
7.Press the ENTER/OK button to confirm your setting.
Auto Store: Automatically scans for and stores channels available in the local area.
Clock Set: Sets the current time for the TV clock.
If you want to reset this feature...
1.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Setup", then press the
ENTER/OK button.
2.Press the ENTER/OK button again, to select "Plug & Play".
3.The message to "Start Plug & Play" is displayed.
TV |
Setup |
|
Plug & Play |
|
|
Language |
: English |
|
Time |
|
|
Game Mode |
: Off |
|
Blue Screen |
: Off |
|
Melody |
: Off |
|
PC |
|
|
Home Theatre PC |
: Off |
|
Light Effect |
: Off |
|
sMore |
|
|
Move |
Enter |
Return |
Plug & Play
Start Plug & Play.
OK
Enter
Return
English - 10
You can scan for the frequency ranges available to you (and |
|
|
|
|
TV |
Channel |
|
||
availability depends on your country). |
Auto Store |
|
|
|
Automatically allocated programme numbers may not |
Manual Store |
|
|
|
correspond to actual or desired programme numbers. However, |
Channel Manager |
|
||
you can sort numbers manually and clear any channels you do |
Sort |
|
|
|
Name |
|
|
||
not wish to watch. |
Fine Tune |
|
|
|
1. |
Press the MENU button to display the menu. |
LNA |
: Off |
|
|
|
|
||
|
Press the ▲ or ▼ button to select "Channel", then press the |
|
|
|
2. |
ENTER/OK button. |
Move |
Enter |
Return |
Press the ▲ or ▼ button to select “Auto Store" then press |
|
|
|
|
|
the ENTER/OK button. |
|
|
|
3. |
Press the ENTER/OK button. |
|
|
|
The TV will begin memorizing all of the available channels.
Press the ENTER/OK button at any time to interrupt the memorization process and return to the "Channel" menu.
4. After all the available channels are stored, the "Sort" menu appears.
English - 11
You can store up to 100 channels, including those received via cable networks. When storing channels manually, you can choose:
Whether or not to store each of the channels found.
The programme number of each stored channel which you wish to identify.
1.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the ENTER/OK button.
2.Press the ▲ or ▼ button to select "Manual Store", then press the ENTER/OK button.
3.Press the ENTER/OK button to select "Programme".
4.To assign a programme number to a channel, find the correct number by pressing the ▲ or ▼ button and then press the ENTER/OK button.
You can also set a programme number by pressing number buttons on the remote control.
5.Press the ▲ or ▼ button to select "Colour System", then press the ENTER/OK button.
6.Select the colour standard required by pressing the ▲ or ▼ button then, press the ENTER/OK button.
7.Press the ▲ or ▼ button to select "Sound System", then press the ENTER/OK button.
8.Select the sound standard required by pressing the ▲ or ▼ button, then press the ENTER/OK button.
If there is an abnormal sound or no sound, re-select the sound system required.
9.If you know the number of the channel to be stored, press the ▲ or ▼ button to select "Channel". Press the ENTER/OK button. Select C (Air channel) or S (Cable channel) by pressing the or button. Press the button to select channel.
Select the required number by pressing the ▲ or ▼ button and then press the ENTER/OK button.
Channel mode: P (Programme mode), C (Air channel mode), S (Cable channel mode)
You can also set a channel number by pressing number buttons on the remote control.
10.If you do not know the channel numbers, press the ▲ or ▼ button to select "Search". Press the ENTER/OK button. Search by pressing the ▲ or ▼ button and then press the
ENTER/OK button.
11.Press the ▲ or ▼ button to select "Store". Press the ENTER/OK button to select "OK".
12.Repeat steps 3 to 11 for each channel to be stored.
Programme: Selects a program number for the channel.
Colour System: Sets the colour supporting system.
Sound System: Sets the sound supporting system.
Channel: Selects a channel.
Search: Scans for the frequency value for the channel.
Store: Saves your settings.
English - 12
Set the channels according to your preference.
You can easily delete, add, or lock the channel you want.
1.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
2.Press the ▲ or ▼ button to select "Channel Manager", then press the ENTER/OK button.
3.Press the ENTER/OK button again, to select "Channel List".
4.Press the ► button to select " " line.
5.Press the ▲ or ▼ button to select the undesired channel, then press the ENTER/OK button to cancel.
6.Repeat steps 5 for each channel to be select or cancel.
7.Press the EXIT button to exit.
"
" is active when "Child Lock" is selected to "On".
You can select these options by simply pressing the CH LIST button on the remote control.
You can press EXIT button to exit the menu.
Channel List
P 1 C3
1 / 10
Prog. |
|
0 |
C-- |
1 |
C3 |
2 |
BBC 1 |
3 |
C74 |
4 |
C75 |
5 |
C76 |
6 |
S3 |
7 |
S4 |
8 |
S6 |
9 |
S7 |
Add |
Lock |
Move |
Enter |
Page |
Return |
This feature allows you to prevent unauthorized users, such as children, from watching
unsuitable programmes by muting out video and audio. Child Lock cannot be released using the buttons on the side. Only the remote control can release the Child Lock setting, so keep the remote control away from children.
1.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
2.Press the ▲ or ▼ button to select "Channel Manager", then press the ENTER/OK button.
3.Press the ▲ or ▼ button to select "Child Lock", then press the ENTER/OK button.
4.Press the ▲ or ▼ button to select "On" or "Off". Press the
ENTER/OK button.
5.Press the ▲ or ▼ button to select "Channel List", then press the ENTER/OK button.
6.Press the ► button to select "" line.
7.Press the ▲ or ▼ button to select the channels you want to lock, then press the ENTER/OK button.
8.Repeat steps 7 for each channel to be locked or unlocked.
9.Press the EXIT button to exit.
Select "On" or "Off" in "Child Lock" to easily turn the channels which selected on "
" to be active or inactive.
TV |
Channel Manager |
||
|
Channel List |
|
|
|
Child Lock |
: |
Off |
|
|
|
On |
|
Move |
Enter |
Return |
|
|
Channel List |
|||||||
P 2 |
C4 |
BBC1 |
|||||||
|
|
1 / 10 |
|||||||
Prog. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0 |
C-- |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 |
C3 |
|
|
|
|
|
|
|
|
2 |
BBC 1 |
|
|
|
|
|
|
|
|
3 C74
4 C75
5 C76
6 S3
7 S4
8 S6
|
9 |
S7 |
|
|
|
|||||
|
|
|
|
|
|
Add |
|
|
Lock |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Move |
|
Enter |
||
|
|
|
|
|
|
Page |
|
Return |
||
|
|
|
|
|
|
|
|
|
|
|
English - 13
You can exchange the numbers of two channels, in order to:
Modify the numeric order in which the channels have been automatically stored.
Give easily remembered numbers to the channels that you watch most often.
1.Press the MENU button to display the menu. Press the ▲ or ▼ button to select "Channel", then press the ENTER/OK button.
2.Press the ▲ or ▼ button to select "Sort", then press the
ENTER/OK button.
3.Select the channel number that you wish to change by press ing the ▲ or ▼ button repeatedly. Press the ENTER/OK button.
The selected channel number and name are moved to right side.
4.Press the ▲ or ▼ button to move to the position in which you would like to change and then press the ENTER/OK button. The selected channel is exchanged with the one
previously stored to the chosen number.
5.Repeat steps 3 to 4 for another channel to be sorted.
6.Press the EXIT button to exit.
TV |
|
Channel |
|
Auto Store |
|
|
|
Manual Store |
|
|
|
Channel Manager |
|
||
Sort |
|
|
|
Name |
|
|
|
Fine Tune |
|
|
|
LNA |
|
: Off |
|
Move |
Enter |
Return |
|
TV |
|
Sort |
|
Prog. |
Ch. |
Name |
|
0 |
Cr-- |
|
|
1 |
C23 |
|
|
2 |
C16 |
|
|
3 |
C3 |
|
|
4 |
S1 |
|
|
|
r |
|
|
Move
Enter
Return
Channel names will be assigned automatically when channel information is broadcast. These names can be changed, allowing you to assign new names.
1.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
2.Press the ▲ or ▼ button to select "Name", then press the
ENTER/OK button.
3.If necessary, select the channel to be assigned to a new name by pressing the ▲ or ▼ button. Press the ENTER/OK button.
The selection bar is displayed around the name box.
4. |
|
|
|
To... |
Then... |
||
|
|||
|
Select a letter, number or symbol |
Press the or button |
|
|
|
|
|
|
Move on the next letter |
Press the button |
|
|
|
|
|
|
Move back the previous letter |
Press the button |
|
|
|
|
|
|
Confirm the name |
Press the ENTER/OK |
|
|
|
button |
The characters available are : Letters of the alphabet
(A~Z) / Numbers (0~9) / Special characters ( -, space, +,/,*)
5.Repeat steps 3 to 4 for each channel to be assigned to a new name.
6.Press the EXIT button to exit.
TV |
Channel |
|
Auto Store |
|
|
Manual Store |
|
|
Channel Manager |
|
|
Sort |
|
|
Name |
|
|
Fine Tune |
|
|
LNA |
: Off |
|
Move |
Enter |
Return |
TV |
Name |
|
Prog. Ch. Name
0 |
Cr-- |
----- |
1 |
C23 |
----- |
2 |
C16 |
----- |
3 |
C3 |
----- |
4 |
S1 |
----- |
|
r |
|
Move
Enter
Return
English - 14
Use fine tuning to manually adjust a particular channel for optimal reception.
1.Use the number buttons to directly select the channel that you want to fine tune.
2.Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the
ENTER/OK button.
3.Press the ▲ or ▼ button to select "Fine Tune", then press the ENTER/OK button.
4.Press the ◄ or ► button to adjust the fine tuning. Press the ENTER/OK button.
5.Press the EXIT button to exit.
Fine tuned channels that have been saved are marked with an asterisk "*" on the right-hand side of the channel number in the channel banner. And the channel number turns red.
To reset the fine-tuning, select "Reset" by pressing the ▲ or ▼ button and then press the ENTER/OK button.
TV |
Channel |
|
Auto Store |
|
|
Manual Store |
|
|
Channel Manager |
|
|
Sort |
|
|
Name |
|
|
Fine Tune |
|
|
LNA |
: Off |
|
Move |
Enter |
Return |
|
Fine Tune |
|
P 1 |
|
|
|
|
0 |
|
Reset |
|
Adjust |
Save |
Return |
If the TV is operating in a weak-signal area, sometimes the LNA function can improve the reception (a low-noise preamplifier boosts the incoming signal).
1.Press the MENU button to display the menu.
Press the ▲ or ▼ buttons to select “Channel”, then press the ENTER/OK button.
2.Press the ▲ or ▼ buttons to select “LNA”, then press the
ENTER/OK button.
3.Press the▲ or ▼ buttons to select “On”, or "Off".
Press the ENTER/OK button.
4.Press the EXIT button to exit.
TV |
Channel |
|
Auto Store |
|
|
Manual Store |
|
|
Channel Manager |
|
|
Sort |
|
|
Name |
|
|
Fine Tune |
|
|
LNA |
: Off |
|
Move |
Enter |
Return |
TV |
Channel |
|
Auto Store
Manual Store
Channel Manager
Sort
Name
Fine Tune
LNA |
: |
OffOff |
|
|
On |
Move
Enter
Return
English - 15
You can select the type of picture which best corresponds to your viewing requirements.
1.Press the MENU button to display the menu. Press the ENTER/OK button to select "Picture".
2.Press the ENTER/OK button again, to select "Mode".
3.Press the ▲ or ▼ button to select the desired picture effect. Press the ENTER/OK button.
4.Press the EXIT button to exit.
Dynamic: Selects the picture for high-definition in a bright room.
Standard: Selects the picture for optimum display in a normal environment.
Movie: Selects the picture for comfortable display in a dark room.
The Picture mode must be adjusted separately for each input source.
You can return to the factory defaults picture settings by selecting the "Reset".
(Refer to "Resetting the Picture Settings to the Factory Defaults" on page 21)
TV |
|
Picture |
|
Mode |
|
: Dynamic |
|
Contrast |
|
|
100 |
Brightness |
|
|
45 |
Sharpness |
|
|
75 |
Colour |
|
|
55 |
Tint |
G50 |
|
R50 |
Colour Tone |
|
: Cool1 |
|
Detailed Settings |
|
|
|
sMore |
|
|
|
Move |
|
Enter |
Return |
TV |
|
Picture |
|
Mode |
|
: Dynamic |
|
Contrast |
|
|
Dynamic |
|
|
Standard |
|
Brightness |
|
|
Movie |
Sharpness |
|
|
75 |
Colour |
|
|
55 |
Tint |
G50 |
|
R50 |
Colour Tone |
|
: Cool1 |
|
Detailed Settings |
|
|
|
sMore |
|
|
|
Move |
|
Enter |
Return |
You can also press the P.MODE button on the remote control to select one of the picture settings.
Your set has several settings which allow you to control picture quality.
1.To select the desired picture effect, follow the
"Changing the Picture Standard" instructions number 1 to 3 on page 16.
2.Press the ▲ or ▼ button to select a particular item. Press the
ENTER/OK button.
3.Press the ◄ or ► button to decrease or increase the value of a particular item. Press the ENTER/OK button.
TV |
|
Picture |
|
Mode |
|
: Dynamic |
|
Contrast |
|
|
100 |
Brightness |
|
|
45 |
Sharpness |
|
|
75 |
Colour |
|
|
55 |
Tint |
G50 |
|
R50 |
Colour Tone |
|
: Cool1 |
|
Detailed Settings |
|
|
|
sMore |
|
|
|
Move |
|
Enter |
Return |
4.Press the EXIT button to exit.
Contrast: Adjusts the lightness and darkness between objects and the background.
Brightness: Adjusts the brightness of the whole screen.
Sharpness: Adjusts the outline of objects to either sharpen them or make them more dull.
Colour: Adjusts the colours, making them lighter or darker.
Tint(NTSC or DTV): Adjusts the colour of objects, making them more red or green for a more natural look.
The adjusted values are stored according to the selected Picture mode.
In PC Mode, Only "Contrast", "Brightness" can be adjusted.
English - 16
You can select the most comfortable colour tone to your eyes.
1.To select the desired picture effect, follow the
"Changing the Picture Standard" instructions number 1 to 3 on page 16.
2.Press the or button to select "Colour Tone", then press the ENTER/OK button.
3.Press the or button to select the desired colour tone setting. Press the ENTER/OK button.
4.Press the EXIT button to exit
Cool2: Makes the colour temperature bluer than "Cool1" menu.
Cool1: Makes whites bluish.
Normal: Keeps whites white.
Warm1: Makes whites reddish.
Warm2: Makes the colour temperature redder than "Warm1" menu.
The adjusted values are stored according to the selected Picture mode.
When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.
TV |
|
Picture |
|
|
Mode |
|
: Dynamic |
|
|
Contrast |
|
|
|
100 |
Brightness |
|
|
|
45 |
Sharpness |
|
|
|
75 |
Colour |
|
|
|
55 |
Tint |
G50 |
|
|
R50 |
Colour Tone |
|
: Cool1 |
|
|
Detailed Settings |
|
|
|
|
sMore |
|
|
|
|
Move |
|
Enter |
Return |
|
TV |
|
Picture |
|
|
Mode |
|
: Dynamic |
|
|
Contrast |
|
|
|
100 |
Brightness |
|
|
|
45 |
Sharpness |
|
|
|
75 |
Colour |
|
Cool 2 |
55 |
|
Tint |
G50 |
R50 |
||
Colour Tone |
|
: Cool1Cool 1 |
|
|
Detailed Settings |
Normal |
|
||
|
|
Warm 1 |
|
|
sMore |
|
Warm 2 |
|
Move
Enter
Return
English - 17
You can set detailed picture settings.
1Press the MENU button to display the menu.
2Press the ENTER/OK button, to select "Picture".
3Press the ▲ or ▼ button to select Detailed Settings, then press the ENTER/OK button.
4Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button.
Available options: Black Adjust, Dynamic Contrast, Gamma, White Balance, My Colour Control, Edge Enhancement, Colour Space.
5When you are satisfied with your setting, press the ENTER/OK button.
6Press the EXIT button to exit.
When the picture mode is set to Movie or Detailed Settings can be selected.
If DNIe is Off, the Detailed Settings cannot be selected when the Picture mode is in Standard mode.
TV |
|
Picture |
|
|
Mode |
|
|
: Movie |
|
Contrast |
|
|
|
100 |
Brightness |
|
|
|
45 |
Sharpness |
|
|
|
75 |
Colour |
|
|
|
55 |
Tint |
G50 |
|
|
R50 |
Colour Tone |
|
|
: Cool1 |
|
Detailed Settings |
|
|
|
|
sMore |
|
|
|
|
Move |
|
Enter |
Return |
|
TV |
Detailed Settings |
|||
Black Adjust |
|
: Off |
|
|
Dynamic Contrast |
: Off |
|
||
Gamma |
|
|
: 0 |
|
White Balance |
|
|
|
|
My Colour Control |
|
|||
Edge Enhancement : Off |
|
|||
Colour Space |
|
: Auto |
|
Move
Enter
Return
Black Adjust: Off/Low/Medium/High
You can directly select the black level on the screen to adjust the screen depth.
Dynamic Contrast: Off/Low/Medium/High
You can adjust the screen contrast so that the optimal contrast is provided.
Gamma: -3 ~ 3
You can adjust the middle brightness of pictures.
Press the ◄ or ► button until you reach the optimal setting.
White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset
You can adjust the color temperature for more natural picture colors. R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the adjusted screen.
Select the required option by pressing the ▲ or ▼ button, then press the ENTER/OK button. Press the ◄ or ► button until you reach the optimal setting.
Reset: The previously adjusted white balance will be reset to the factory defaults.
My Colour Control: Pink/Green/Blue/White/Reset
This setting can be adjusted to suit your personal preferences.
When running the My Colour Control feature, the current picture is captured as a still image before being displayed on the screen.
Edge Enhancement: On/Off
You can emphasize object boundaries.
Colour Space: Auto/Wide
You can set the color reproduction space for the input signal to Auto or Wide.
English - 18
You can select the picture size which best corresponds to your viewing requirements.
1.Press the MENU button to display the menu. Press the ENTER/OK button , to select "Picture".
2.Press the ▲ or ▼ button to select "Size", then press the
ENTER/OK button.
3.Select the required option by pressing the ▲ or ▼ button. Press the ENTER/OK button.
4.Press the EXIT button to exit.
16:9: Adjusts the picture size to 16:9 appropriate for DVDs or wide broadcasting.
Wide Zoom: Magnify the size of the picture more than 4:3..
Zoom: Magnifies the 16:9 wide picture (in the vertical direction) to fit the screen size.
4:3: This is the default setting for a video movie or normal broadcasting.
Just Scan : Displays the input scenes as they are without any cutoff when 720p, 1080i signals are input.
TV |
Picture |
|
rMore |
|
|
Size |
: Zoom |
|
Digital NR |
: Auto |
|
Active Colour |
: Off |
|
DNle |
: Off |
|
Movie Plus |
: On |
|
Reset |
: OK |
|
Move |
Enter |
Return |
|
Size |
|
16 : 9 |
|
|
Wide Zoom |
|
|
Zoom |
|
|
4 : 3 |
|
|
Just Scan |
|
|
Move |
Enter |
Return |
"Wide Zoom" function is available only in"TV", "AV1", "AV2", "Component1","Component2","HDMI1","HDMI2","HDMI3", and "S-Video" mode. (HDMI3 is only available for PS42Q91HD and PS50Q91HD)
In PC Mode, only "16:9" and "4:3" mode can be adjusted.
Just Scan Mode is available only HDMI mode
Zoom: Select by pressing the ◄ or ► buttons.
Use the ▲ or ▼ button to move the picture up and down. After selecting , use the ▲ or ▼ button to magnify or reduce the picture size in the vertical direction.
Wide Zoom : Move the screen up/down using the▲ or ▼
buttons after selecting the by pressing the ► or ENTER/OK button.
You can select these options by simply pressing the P.SIZE button on the remote control.
Press the STILL button to freeze a moving picture into a still one. Press again to cancel.
English - 19