STEP 6
Press the Trim Frame into the opening
until all sides snap into place.
Open the oven door. Secure the Trim
Frame using SCREW B. (2 ea)
Installation
STEP 5
1. Slide the oven with Duct Base into
cabinet until Duct Base touch the
front of cabinet.
2. Plug the Power cord into the
electrical outlet.
3. Secure together by using SCREW A
provided in the kit. (2 ea)
NOTE
Be aware when you put a oven into the
cabinet because cabinet may be moved.
After placing the Side Bracket to match
with holes, secure together by using
SCREW A provided in the kit. (4 ea)
Trim Frame
Align the Center with cabinet
Upper
Bottom
Side Bracket
Installation Instructions
Built-in Trim Kit
(MA-TK3080CK/AA, MA-TK3080CT/AA)
STEP 3
1. Remove 2 screws from the lower right
and left parts of outer panel, 1screw
of each side and dispose them.
2. Remove a SCREW C(#1) from back of
oven. Do not scrap SCREW C(#1)
STEP 4
1. Place oven on the Duct Base.
2. Position Duct Side on the left of the
oven inserting edge. Secure together
by using SCREW C provided in the kit
(2 ea) and SCREW C(#1).
NOTE
Please remove the double-sided tape
before inserting Duct Side.
Back
Front
Duct side
SCREW
C (#1)
Duct Base
SCREW
C (#1)
DE68-04377A-00
(�����)MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd 1-4 2015-06-15 �� 11:16:10
BEFORE YOU BEGIN Parts included in the kits Installation
Trim Frame (1 EA) Duct Base (1 EA) Duct Side (1 EA) Side Bracket (2EA)
Screw A
(5/8" length) (6EA)
Screw B
(15/32" length)
(2EA)
Screw C
(25/64" length)
(2EA)
Template (1 EA)
Screwdriver Pencil Drill with 7/64 or #35
Drill bit
Scissors Tape measure
STEP 1
CUTOUT DIMENSIONS
Height 18 3/4" ± 1/16"
Width 24" ± 1/16"
Depth 21 1/2" ± 1/16"
WARNING
To avoid risk of electrical shock,
personal injury, or death:
-Before drilling into the wall, note
where electrical outlets are and where
electrical wire might be concealed
behind the wall. YOU COULD GET AN
ELECTRICAL SHOCK if you contact
electrical wire with the drill bit.
-Locate and disconnect the power to any
electrical circuits that could be affected
by installing this oven.
IF YOU DO NOT DISCONNECT THE
POWER, YOU COULD GET AN ELECTRICAL
SHOCK.
WARNING
To avoid personal injury, wear gloves
when handling the metal parts. Parts are
sharp and can cause cuts and abrasions.
IMPORTANT
- Save these instructions for local inspector's use.
- Observe all governing codes and coordinates.
- Be sure to disconnect the plug of the microwave oven from the electrical outlet
before installing the Builtin Kit. Remove the turntable from the oven cavity.
- The kit includes metal parts, due caution should be used in handling and installation
to avoid the possibility of injury.
- Do not remove permanently affixed labels, warnings or plates from the product.
Doing so may void the warranty.
Warning
- The electrical requirements for this oven are 115-120 volts AC, 15 amps
or larger.
Read these instructions completely and carefully.
STEP 2
After placing the Template to match
with cabinet center line mark four Holes
at the bottom.
After placing the Template to match with
center line, mark two Holes at the top.
Then drill a pilot hole at 6 positions use
7/64 or #35 Drill bit.
NOTE
You may not be assembled when using
the thicker Drill bit.
A : 11 9/32" (287 mm)
B : 6 57/64" (175 mm)
C : 9 23/32" (247 mm)
Depth
High
3" min
Electric Heat
Source Model
Width
P1
P2
P3
P4
CENTER
LINE
A
A
B B
C C
A
A
CABINET
OPENING
P5
P1 P3
P2
P6
P4
P5
P6
Tools needed
(�����)MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd 5-8 2015-06-15 �� 11:16:11
Loading...