Samsung MA-TK3080CK, MA-TK3080CT Installation Guide

Installation

STEP 3

STEP 5

Installation Instructions

STEP 6

STEP 4

SCREW

C (#1)

Duct Base

1. Remove 2 screws from the lower right

and left parts of outer panel, 1screw of each side and dispose them.

2. Remove a SCREW C(#1) from back of

oven. Do not scrap SCREW C(#1)

1. Place oven on the Duct Base.

Back

Front

Side Bracket

1. Slide the oven with Duct Base into

cabinet until Duct Base touch the front of cabinet.

2. Plug the Power cord into the

electrical outlet.

3. Secure together by using SCREW A

provided in the kit. (2 ea)

NOTE

Be aware when you put a oven into the cabinet because cabinet may be moved.

Align the Center with cabinet

After placing the Side Bracket to match with holes, secure together by using SCREW A provided in the kit. (4 ea)

Trim Frame

Press the Trim Frame into the opening until all sides snap into place.

Upper

Bottom

Open the oven door. Secure the Trim Frame using SCREW B. (2 ea)

Built-in Trim Kit

(MA-TK3080CK/AA, MA-TK3080CT/AA)

SCREW C (#1)

oven inserting edge. Secure together by using SCREW C provided in the kit (2 ea) and SCREW C(#1).

2. Position Duct Side on the left of the

NOTE

Please remove the double-sided tape

Duct side

(��)MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd 1-4 2015-06-15 �� 11:16:10

before inserting Duct Side.

DE68-04377A-00

BEFORE YOU BEGIN Parts included in the kits Installation

Read these instructions completely and carefully.

IMPORTANT

- Save these instructions for local inspector's use.

- Observe all governing codes and coordinates.

- Be sure to disconnect the plug of the microwave oven from the electrical outlet before installing the Builtin Kit. Remove the turntable from the oven cavity.

- The kit includes metal parts, due caution should be used in handling and installation to avoid the possibility of injury.

- Do not remove permanently affixed labels, warnings or plates from the product. Doing so may void the warranty.

Warning

- The electrical requirements for this oven are 115-120 volts AC, 15 amps or larger.

Trim Frame (1 EA) Duct Base (1 EA) Duct Side (1 EA) Side Bracket (2EA)

Screw A

(5/8" length) (6EA)

Screw B

(15/32" length)

(2EA)

Screw C

(25/64" length)

(2EA)

Template (1 EA)

Tools needed

Screwdriver Pencil Drill with 7/64 or #35

Drill bit

STEP 1

Width

Depth

3" min

Electric Heat

Source Model

STEP 2

CUTOUT DIMENSIONS

Height 18 3/4" ± 1/16"

Width 24" ± 1/16"

High

Depth 21 1/2" ± 1/16"

WARNING

To avoid risk of electrical shock, personal injury, or death:

-Before drilling into the wall, note where electrical outlets are and where electrical wire might be concealed behind the wall. YOU COULD GET AN

ELECTRICAL SHOCK if you contact electrical wire with the drill bit.

-Locate and disconnect the power to any electrical circuits that could be affected by installing this oven.

IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRICAL SHOCK.

WARNING

To avoid personal injury, wear gloves when handling the metal parts. Parts are sharp and can cause cuts and abrasions.

CENTER LINE

After placing the Template to match with cabinet center line mark four Holes at the bottom.

After placing the Template to match with center line, mark two Holes at the top.

Then drill a pilot hole at 6 positions use

7/64 or #35 Drill bit.

NOTE

You may not be assembled when using the thicker Drill bit.

A : 11 9/32" (287 mm)

B : 6 57/64" (175 mm)

C : 9 23/32" (247 mm)

CABINET OPENING

Scissors Tape measure

P1 P3

(��)MA-TK3080CK_AA_MA-TK3080CT_AA_DE68-04377A-00.indd 5-8 2015-06-15 �� 11:16:11

C C

B B