SAMSUNG LN32A330, LN32A330J1D, LN37A330J1D, LN40A330 User Manual

Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Comment contacter Samsung dans le monde
Si vous avez des suggestions ou des questions concernant les produits Samsung, veuillez contacter le Service Consommateurs Samsung.
Country
CANADA 1-800-SAMSUNG(726-7864) www.samsung.com/ca
U.S.A 1-800-SAMSUNG(726-7864) www.samsung.com
Customer Care Center
Samsung Electronics Canada Inc., Customer Service 55 Standish Court Mississauga, Ontario L5R 4B2 Canada
Samsung Electronique Canada Inc., Service à la Clientèle 55 Standish Court Mississauga, Ontario L5R 4B2 Canada
Samsung Electronics America, Inc. 105 Challenger Road Ridgefield Park, NJ 07660-0511
LCD TV
user manual
BN68-01514B-00
imagine the possibilities
Thank you for purchasing a Samsung product. To receive a more complete service, please register your product at
www.samsung.com/global/register
Model Serial No.
Important Warranty Information Regarding Television Format Viewing
Wide screen format LCD Displays (16:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving. Displaying stationary graphics and images on screen, such as the dark side-bars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing per week. Additionally, viewing other stationary images and text such as stock market reports, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LCD Displays that leave subtle, but permanent burned-in ghost images in the LCD picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On LCD models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful in the selection and duration of television formats used for viewing. Uneven LCD aging as a result of format selection and use, as well as burned-in images, are not covered by your Samsung limited warranty.
U.S.A Only
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. In particular, this product is licensed under the following US patents: 5,991,715, 5,740,317, 4,972,484, 5,214,678, 5,323,396, 5,539,829, 5,606,618, 5,530,655, 5,777,992, 6,289,308, 5,610,985, 5,481,643, 5,544,247, 5,960,037, 6,023,490, 5,878,080, and under US Published Patent Application No. 2001-44713-A1. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
Other countries
The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT
Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specified, and to the Original Purchaser only.
The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser.
Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product.
Excluded, but not limited to, are any originally specified provisions for, in-home or on-site services, minimum or maximum repair times, exchanges or replacements, accessories, options, upgrades, or consumables.
For the location of a SAMSUNG Authorized Service Center, please call toll-free:
In the United States : 1-800-SAMSUNG (1-800-726-7864) In Canada : 1-800-SAMSUNG
See the warranty card for more information on warranty terms.
Precautions When Displaying a Still Image
A still image may cause permanent damage to the TV screen
• Do not display a still image on the LCD panel for more than 2 hours as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
Watching the LCD TV in 4:3 format for a long period of time may leave traces of borders displayed on the left, right and
• Displaying still images from Video games and PC for longer than a certain period of time may produce partial after-images.
To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when displaying still images.
© 2008 Samsung Electronics Co., Ltd. All rights reserved.
center of the screen caused by the difference of light emission on the screen. Playing a DVD or a game console may cause a similar effect to the screen. Damages caused by the above effect are not covered by the Warranty.

Contents

English
GENERAL INFORMATION
List of Features ............................................................................. 2
Accessories ..................................................................................2
Viewing the Control Panel ...........................................................3
Viewing the Connection Panel ....................................................4
Remote Control ............................................................................ 5
Installing Batteries in the Remote Control ....................................6
CONNECTIONS
Connecting VHF and UHF Antennas ............................................6
Connecting Cable TV ................................................................... 7
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via HDMI ................................................................8
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via DVI ...................................................................8
Connecting a DVD Player or Cable Box/Satellite receiver
(Set-Top Box) via Component cables ........................................... 9
Connecting a Camcorder ............................................................9
Connecting a VCR ...................................................................... 10
Connecting a Digital Audio System ............................................ 11
Connecting an Amplier/DVD Home Theater ............................. 11
Connecting a PC ........................................................................ 12
OPERATION
Turning the TV On and Off .........................................................13
Plug & Play Feature ...................................................................13
Changing Channels .................................................................... 14
Adjusting the Volume ..................................................................15
Viewing the Display ....................................................................15
Viewing the Menus .....................................................................15
Using the TOOLS Button ............................................................ 16
Memorizing the Channels ........................................................... 16
To Select the Source ..................................................................18
To Edit the Input Source Name ..................................................18
PC DISPLAY
Using Your TV as a Computer (PC) Display ............................... 34
Display Modes ............................................................................ 34
Setting up the TV with your PC .................................................. 35
TIME SETTING
Setting the Clock ........................................................................ 37
FUNCTION DESCRIPTION
Selecting a Menu Language ....................................................... 40
Using the V-Chip ........................................................................ 41
Viewing Closed Captions (On-Screen Text Messages) - Analog
Viewing Closed Captions (On-Screen Text Messages) - Digital
Adjusting the TV On/Off Melody Sound......................................50
Using the Energy Saving Feature ..............................................50
Upgrading the Software .............................................................. 51
APPENDIX
Troubleshooting .......................................................................... 52
Installing the Stand ..................................................................... 54
Disconnecting the Stand ............................................................54
Auto Wall-Mount Adjustment (Sold separately)
(LN32A330J1D, LN37A330J1D, LN40A330J1D)............................ 55
Wall Mount Kit Specications (VESA) ........................................56
Using the Anti-Theft Kensington Lock ........................................57
Specications ............................................................................. 58
Dimensions ................................................................................. 59
...... 48
....... 49
PICTURE CONTROL
Changing the Picture Standard .................................................. 19
Customizing the Picture Settings ...............................................19
Conguring Picture Options .......................................................20
Resetting the Picture Settings to the Factory Defaults ............... 23
SOUND CONTROL
Changing the Sound Standard ...................................................24
Customizing the Sound .............................................................. 24
Setting the TruSurround XT ........................................................25
Choosing a Multi-Channel Sound (MTS) track - Digital ............. 25
Choosing a Multi-Channel Sound (MTS) track - Analog ............26
Automatic Volume Control .......................................................... 26
Setting the TV Speakers On/Off ................................................. 27
CHANNEL CONTROL
Clearing Scrambled Channels - Digital ......................................28
Adding and Erasing Channels .................................................... 29
To Set-Up Your Favorite Channels .............................................30
Viewing the Channel Lists ..........................................................31
Labeling Channels ...................................................................... 32
Fine Tuning Analog Channels ....................................................33
Checking the Digital-Signal Strength .......................................... 33
Symbol Press Note One-Touch
Button
English - 1

General Information

List of Features

Adjustable picture settings that can be stored in the TV’s memory. Automatic timer to turn the TV on and off. A special sleep timer. Excellent Digital Interface & Networking :
With a built-in HD digital tuner, non-subscription HD broadcasts can be viewed with no Cable Box/Satellite receiver
(Set-Top Box) needed.
HDMI/DVI connection of your PC to this TV. Excellent Picture Quality SRS TruSurround XT
- SRS TruSurround XT provides a virtual surround system.

Accessories

Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer.
Remote Control & Batteries (AAA x 2)
(BN59-00678A)
Cover-Bottom
(LN26A330J1D: BN63-03176A) (LN32A330J1D: BN63-03093A) (LN37A330J1D: BN63-03127A) (LN40A330J1D: BN63-03127A)
Stand (LN26A330J1D: BN96-04745A) (LN32A330J1D: BN96-07542A) (LN37A330J1D: BN96-07541A) (LN40A330J1D: BN96-07541A)
The items color and shape may vary depending on the model.
Power Cord
(3903-000144)
Owner’s Instructions
Stand Screw (M4XL16)
(6002-001294)
Cleaning Cloth
(BN63-01798A)
Warranty Card / Registration Card /
Safety Guide Manual
(Not available in all locations)
Stand Screw (M4XL14) (LN32A330J1D: 6003-001334) (LN37A330J1D: 6003-001334) (LN40A330J1D: 6003-001334)
English - 2

Viewing the Control Panel

Buttons on the Lower-Right Part of the Panel
The buttons on the lower-right panel control your TV’s basic features, including the on-screen menu. To use the more advanced features, you must use the remote control.
Side Panel buttons
1
2
3
4
The product color and shape may vary depending on the model.
1
SOURCE
Toggles between all the available input sources
(TV, AV, Component1, Component2, PC, HDMI1, HDMI2). In the on-screen menu, use this button as you would use the ENTER button on the remote control.
2
MENU
Press to see an on-screen menu of your TV’s features.
3
+ VOL -
Press to increase or decrease the volume. In the on-screen menu, use the + VOL - buttons as you
would use the ◄ and ► buttons on the remote control.
4 < CH >
Press to change channels. In the on-screen menu, use the < CH
would use the ▼ and ▲ buttons on the remote control.
>
buttons as you
565
5
SPEAKERS
6
(POWER)
Press to turn the TV on and off.
REMOTE CONTROL SENSOR Aim the remote control towards this spot on the TV.
POWER INDICATOR Blinks and turns off when the power is on and lights up in stand-by mode.
English - 3

Viewing the Connection Panel

Use the connection panel jacks to connect A/V components that will be connected continuously, such as DVD players or a VCR. For more information on connecting equipment, see pages 6~12.
The product color and shape may vary depending on the model.
1
AUDIO OUT
Connects to the audio input jacks on your Amplifier/
Home theater.
2 DIGITAL AUDIO OUT (OPTICAL) Connects to a Digital Audio component.
3 PC IN [PC] / [AUDIO] Connects to the video and audio output jacks on your
PC.
4 HDMI IN 1, 2 / DVI IN(HDMI2)[R-AUDIO-L]
Connects to the HDMI jack of a device with an HDMI
output. Use the HDMI IN 2 jack for DVI connection to an external device. Use a DVI to HDMI cable or DVI-HDMI adapter (DVI to HDMI) for video connection and the DVI IN (HDMI2) [R-AUDIO-L] jacks for audio.
- No sound connection is needed for an HDMI to HDMI connection.
- When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
5 ANT IN Connects to an antenna or cable TV system.
6
POWER INPUT
Connects the supplied power cord.
7
SERVICE
Connector for SERVICE only.
8 COMPONENT IN 1, 2 / AV 1 The COMPONENT IN 1 jack is also used as the AV IN 1
jack.
- Connect the video cable to the COMPONENT IN 1 [Y/ VIDEO] jack and the audio cable to the COMPONENT IN 1 [R-AUDIO-L] jacks.
9 EX-LINK
- LN26A330J1D
Connector for SERVICE only.
- LN32A330J1D / LN37A330J1D / LN40A330J1D
Connect this to the jack on the optional wall mount bracket. This will allow you to adjust the TV viewing angle using your remote control.
0
KENSINGTON LOCK
The Kensington Lock (optional) is a device used to
physically fix the system when used in a public place. If you want to use a locking device, contact the dealer where you purchased the TV.
The location of the Kensington Lock may be different
depending on its model.
English - 4

Remote Control

You can use the remote control up to a distance of about 23 feet from the TV.
1
POWER
Turns the TV on and off.
2
TV
Selects the TV mode directly.
3
NUMERIC BUTTONS
Press to change the channel.
4
Press to select additional channels(digital and analog) being broadcast by the same station. For example, to select channel “54-3”, press “54”, then press “ ” and “3”.
5 (
MUTE)
Press to temporarily cut off the
sound.
6
VOL / VOL
Press to increase or decrease
the volume.
7 TOOLS Use to quickly select frequently
used functions.
8 UP▲ / DOWN▼ / LEFT◄
RIGHT►
Use to select on-screen menu
items and change menu values.
9 INFO Press to display information on
the TV screen.
0
COLOR BUTTONS
Use these buttons in the
Channel list, etc.
!
CC
Controls the caption decoder.
/ ENTER
/
@ MTS
Press to choose stereo, mono
or Separate Audio Program (SAP broadcast).
#
SOURCE
Press to display and select the
available video sources.
$
PRE CH
Tunes to the previous channel.
% CH / CH
Press to change channels.
^
RETURN
Returns to the previous menu.
& EXIT Press to exit the menu.
*
SRS
Selects SRS TruSurround XT
mode.
(
MENU
Displays the main on-screen
menu.
) FAV.CH
Press to switch to your favorite channels.
a P.SIZE
Picture size selection.
The performance of the remote control may be affected by bright light.
English - 5

Installing Batteries in the Remote Control

1. Lift the cover at the back of the remote control upward as shown in the figure.
2. Install two AAA size batteries.
Make sure to match the "+" and "–" ends of the batteries with the diagram inside the compartment.
3. Replace the cover. Remove the batteries and store them in a cool, dry place if you won’t be using the remote control for a long time. The remote control can be used up to about 23 feet from the TV. (Assuming typical TV usage, the batteries should last for about one year.)
If the remote control doesn’t work, check the following:
1. Is the TV power on?
2. Are the plus and minus ends of the batteries reversed?
3. Are the batteries drained?
4. Is there a power outage or is the power cord unplugged?
5. Is there a special fluorescent light or neon sign nearby?

Connections

Connecting VHF and UHF Antennas

If your antenna has a set of leads that look like the diagram to the right, see "Antennas with
300 Ω Flat Twin Leads" below.
If your antenna has one lead that looks like the diagram to the right, see "Antennas with 75 Ω Round Leads". If you have two antennas, see "Separate VHF and UHF Antennas".
Antennas with 300 Ω Flat Twin Leads
If you are using an off-air antenna (such as a roof antenna or "rabbit ears") that has 300 Ω twin at leads, follow the directions
below.
1. Place the wires from the twin leads under the screws on a 300-75 Ω adapter
(not supplied). Use a screwdriver to tighten the screws.
2. Plug the adaptor into the ANT IN terminal on the back of the TV.
ANT IN
Antennas with 75 Ω Round Leads
1. Plug the antenna lead into the ANT IN terminal on the back of the TV.
ANT IN
Separate VHF and UHF Antennas
If you have two separate antennas for your TV (one VHF and one UHF), you must combine the two antenna signals before connecting the antennas to the TV. This procedure requires an optional combiner-adaptor (available at most electronics shops).
1. Connect both antenna leads to the combiner.
UHF
VHF
2. Plug the combiner into the ANT IN terminal on the bottom of the rear panel.
English - 6
ANT IN
UHF
VHF

Connecting Cable TV

To connect to a cable TV system, follow the instructions below.
Cable without a Cable Box
1. Plug the incoming cable into the ANT IN terminal on the back of the TV.
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable channels.
ANT IN
Connecting to a Cable Box that Descrambles All Channels
1. Find the cable that is connected to the ANT OUT terminal on your cable box. This terminal might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".
ANT IN
ANT OUT
2. Connect the other end of this cable to the ANT IN terminal on the back of the TV.
ANT IN
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels (such as premium channels), follow the instructions below. You will need a two­way splitter, an RF (A/B) switch and four lengths of RF cable. (These items are available at most electronics stores.)
1. Find and disconnect the cable that is connected to the ANT IN terminal on your
cable box.
This terminal might be labeled "ANT IN", "VHF IN" or simply, "IN".
ANT IN
2. Connect this cable to a two-way splitter.
Incoming
cable
Splitter
3. Connect an RF cable between the OUTPUT terminal on the splitter and the IN terminal on the cable box.
Incoming
cable
Splitter
Cable Box
4. Connect an RF cable between the ANT OUT terminal on the cable box and the B–IN terminal on the RF(A/B) switch.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
5. Connect another cable between the other OUT terminal on the splitter and the A–IN
terminal on the RF (A/B) switch.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
6. Connect the last RF cable between the OUT terminal on the RF (A/B) switch and
ANT IN
the ANT IN terminal on the rear of the TV.
Incoming
cable
Splitter
Cable Box
RF (A/B)
Switch
TV Rear
After you have made this connection, set the A/B switch to the "A" position for normal viewing. Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch to "B", you will need to tune your TV to the cable box’s output channel, which is usually channel 3 or 4.)
English - 7

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via HDMI

This connection can only be made if there is an HDMI Output connector on the external device.
1. Connect an HDMI Cable between the HDMI IN (1 or 2) jack on the TV and the HDMI
DVD Player or Cable Box/Satellite receiver
(Set-Top Box) Rear Panel
TV Rear Panel
jack on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
HDMI Cable (Not supplied)
What is HDMI?
• HDMI(High-Definition Multimedia Interface), is an interface that enables the transmission of digital audio and video signals using a single cable.
• The difference between HDMI and DVI is that the HDMI device is smaller in size and has the HDCP (High Bandwidth Digital Copy Protection) coding feature installed.
Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back panel configuration.

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via DVI

This connection can only be made if there is a DVI Output connector on the external device.
1.
Connect a DVI to HDMI Cable or DVI-HDMI Adapter between the HDMI IN 2 jack on the TV and the DVI jack on the DVD Player or Cable Box/Satellite
DVD Player or Cable Box/
Satellite receiver (Set-Top Box)
receiver (Set-Top Box).
2.
Connect Audio Cables between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and the DVD Player or Cable Box/Satellite receiver (Set-Top
Audio Cable
2
(Not supplied)
Box).
DVI to HDMI Cable (Not supplied)1
Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back panel configuration. When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match the color of the connection terminal to the cable. When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
TV Rear Panel
English - 8

Connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box) via Component cables

The rear panel jacks on your TV make it easy to connect a DVD Player or Cable Box/Satellite receiver (Set-Top Box) to your TV.
Connect a Component Cable
1.
between the COMPONENT IN (1 or 2) [Y, PB, PR] jacks on the TV and the COMPONENT [Y, PB, PR] jacks on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
2.
Connect Audio Cables between the COMPONENT IN(1 or 2) [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the DVD Player or Cable Box/Satellite receiver (Set-Top Box).
DVD Player or Cable Box /
Satellite receiver (Set-Top Box)
Audio Cable (Not supplied)
2
Component Cable (Not supplied)
1
Component video separates the video into Y (Luminance (brightness)), Pb (Blue) and Pr (Red) for enhanced video quality. Be sure to match the component video and audio connections. For example, if connecting a Component video cable to COMPONENT IN 1, connect the audio cable to COMPONENT IN 1 also. Each DVD Player or Cable Box/Satellite receiver (Set-Top Box) has a different back panel configuration. When connecting a DVD Player or Cable Box/Satellite receiver (Set-Top Box), match the color of the connection terminal to the cable.
TV Rear Panel

Connecting a Camcorder

They allow you to view the camcorder tapes without using a VCR.
1. Connect a Video Cable between the VIDEO]
AV IN 1 [Y/
jack on the TV and the VIDEO OUT jack on the camcorder.
2. Connect Audio Cables between the AV IN 1 [R-AUDIO-L] jacks on the TV and the AUDIO OUT jacks on the camcorder.
Each Camcorder has a different back panel configuration. When connecting a Camcorder, match the color of the connection terminal to the cable. When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not match the color of the video cable (Yellow).
Camcorder
Audio Cable (Not supplied)
2
Video Cable (Not supplied)1
TV Rear Panel
English - 9

Connecting a VCR

Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system (according to the instructions on pages 6~7). Skip step 1 if you have not yet connected to an antenna or a cable system.
Unplug the cable or antenna
1.
from the back of the TV.
2.
Connect the cable or antenna to the ANT IN terminal on the back of the VCR.
3. Connect an RF Cable between the ANT OUT terminal on the VCR and the ANT IN terminal on the TV.
4.
Connect a Video Cable between the VIDEO OUT jack on the VCR and the AV IN 1 [Y/VIDEO] jack on the TV.
5. Connect Audio Cables between the AUDIO OUT jacks on the VCR and the AV IN 1 [R-AUDIO-L] jacks on the TV.
If you have a “mono”
(non-stereo) VCR, use a Y-connector (not supplied) to hook up to the right and left audio input jacks of the TV. If your VCRis stereo, you mustm connect two cables.
VCR Rear Panel
Audio Cable (Not supplied)
5
Video Cable (Not supplied)4
RF Cable (Not supplied)3
Follow the instructions in “Viewing a VCR or Camcorder Tape” to view your VCR tape.
Each VCR has a different back panel configuration. When connecting a VCR, match the color of the connection terminal to the cable. When connecting to AV IN 1, the color of the AV IN 1 [Y/VIDEO] jack (Green) does not
match the color of the video cable (Yellow).
ANT IN
TV Rear Panel
English - 10

Connecting a Digital Audio System

The rear panel jacks on your TV make it easy to connect a Digital Audio System (Home theater/Receiver) to your TV.
1. Connect an Optical Cable between the “DIGITAL AUDIO OUT (OPTICAL)” jacks on the
Digital Audio System
TV Rear Panel
TV and the Digital Audio Input jacks on the Digital Audio System.
When a Digital Audio System
is connected to the “DIGITAL AUDIO OUT (OPTICAL)” jack: Decrease the volume of the
Optical Cable (Not supplied)
TV and adjust the volume level with the system’s volume control.
5.1CH audio is possible when the TV is connected to an external device supporting 5.1CH. Each Digital Audio System has a different back panel configuration. When the receiver (home theater) is set to On, you can hear sound output from the TV’s
Optical jack. When the TV is displaying a DTV(air) signal, the TV will send out 5.1 chan­nel sound to the Home theater receiver. When the source is a digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from the Home Theater receiver. If you want to hear 5.1 channel audio, connect the DIGITAL AUDIO OUT (OPTICAL) jack on the DVD player or Cable/Satellite Box directly to an Amplifier or Home Theater, not the TV.
Connecting an Amplier/DVD Home Theater
1. Connect Audio Cables between the AUDIO OUT [R-AUDIO-L] jacks on the TV and AUDIO IN [R-AUDIO-L] jacks on the Amplifier/DVD Home Theater.
When an audio amplifier is
connected to the "AUDIO OUT [R-AUDIO-L]" jacks: Decrease the volume of the TV and adjust the volume level with the Amplifier’s volume control.
TV Rear Panel
Amplier/DVD Home Theater
Audio Cable (Not supplied)
Each Amplifier/DVD Home Theater has a different back panel configuration. When connecting an Amplifier/DVD Home Theater, match the color of the connection
terminal to the cable.
English - 11

Connecting a PC

Using the D-Sub Cable
1. Connect a D-Sub Cable between PC IN [PC] connector on the TV and the PC output connector on your computer.
Connect a PC Audio Cable
2.
between the PC IN [AUDIO] jack on the TV and the Audio Out jack of the sound card on your computer.
Using the HDMI/DVI Cable
1. Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your computer.
Connect a 3.5 mm Stereo
2.
mini-plug/2RCA Cable between the DVI IN(HDMI2) [R-AUDIO-L] jack on the TV and the Audio Out jack of the sound card on your computer.
PC
PC Audio Cable (Not supplied)2
D-Sub Cable (Not supplied)1
PC
3.5 mm Stereo mini-plug/2RCA Cable (Not supplied)
2
TV Rear Panel
TV Rear Panel
1
HDMI/DVI Cable (Not supplied)
Each PC has a different back panel configuration. When connecting a PC, match the color of the connection terminal to the cable. When using an HDMI/DVI cable connection, you must use the HDMI IN 2 jack.
English - 12

Operation

Turning the TV On and Off

Press the POWER button on the remote control. You can also use the POWER button on the TV.

Plug & Play Feature

When the TV is initially powered on, basic settings proceed automatically and subsequently.
The Screen Saver is activated if there is no remote control key input for longer than 1 minute while “Plug & Play” is running.
The Screen Saver is activated if there is no operating signal for longer than 15 minutes.
1. Press the The message “Menu Language, Store Demo, Channels and Time will be set.” is
displayed.
Press the ENTER button, then “Select the language of the OSD” menu is automatically displayed.
2. Press the ▲ or ▼ button to select language, then press the ENTER button. The message “Select ‘Home Use’ when installing this TV in your home.” is
displayed.
3. Press the ◄ or ► button to select “Store Demo” or “Home Use”, then press the ENTER button. The message “Select the antennas to memorize.” is displayed.
We recommend setting the TV to “Home Use” mode for the best picture in your
“Store Demo” mode is only intended for use in retail environments. If the unit is accidentally set to “Store Demo” mode and you want to return to
4. Press the ▲ or ▼ button to memorize the channels of the selected connection. Press the ENTER button to select “Start”. Air: “Air” antenna signal.
In Cable mode, you can select the correct signal source among STD, HRC, and
5. The TV will begin memorizing all of the available channels. To stop the search before it has finished, press the ENTER button with “Stop”
After all the available channels are stored, it starts to remove scrambled
POWER
button on the remote control.
home environment.
“Home Use” (Standard): Press the Volume button on the TV. When the volume OSD is displayed, press and hold the MENU button on the TV for 5 seconds.
Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.
IRC by pressing the ▲, ▼, ◄ or ► button, then press the ENTER button. If you have Digital cable, select the cable system signal source for both Analog and Digital. Contact your local cable company to identify the type of cable system that exists in your particular area.
selected.
channels (see page 28). The Auto program menu then reappears. Press the ENTER button when channel memorization is complete. The message “Set the Clock Mode.” is displayed.
Plug & Play
Menu Language, Store Demo,
Channels and Time will be set.
Start
Enter
Plug & Play
Select the language of the OSD.
Language :
Select ‘Home Use’ when installing this TV in your home.
Store Demo
Move Enter
Select the antennas to memorize.
Air Cable Auto
Move Enter Skip
Selects a cable signal type for your location.
analog
STD
HRC IRC
digital
STD
HRC IRC
Move Enter Skip
Auto Program in Progress. DTV Air : 02 Air : 11 DTV Cable : 23 Cable : 21
Enter Skip
Removing scrambled channel.
Enter Skip
English
Español
Français
Move Enter
Plug & Play
Home Use
Plug & Play
Start Start Start
Plug & Play
Start
Plug & Play
Auto Program
Cable 50
Stop
Plug & Play
Auto Program
Stop
50 %
DTV Cable 41
77 %
English - 13
6. Press the ENTER button.
Press the ▲ or ▼ button to select “Auto”, then Press the ENTER button. The message “Set to daylight saving time.” is displayed.
If you select “Manual”, “Enter the current date and time.” is displayed.
(See page 37)
7. Press the ▲ or ▼ button to select “Off” or “On”, then press the ENTER button. The message “Select the time zone in which you live.” is displayed.
8. Press the ▲ or ▼ button to highlight the time zone for your local area. Press the ENTER button. If you have received a digital signal, the time will be
set automatically. If not, see page 37 to set the clock.
9. The message “Enjoy your watching.” is displayed. When you have finished, press the ENTER button.
Auto Program
Plug & Play
Auto Program is completed. 75 Channels are memorized.
DTV Air : 24 Air : 1 DTV Cable : 17 Cable : 33
OK
Enter Skip
Plug & Play
Set the Clock Mode.
Clock Mode :
Move Enter Skip
Set to daylight saving time.
DST :
Move Enter Skip
Select the time zone in which you live.
Newfoundland Atlantic
Eastern
Central Mountain Pacific Alaska Hawaii
Move Enter Skip
Auto
Manual
Plug & Play
Off
On
Plug & Play
Plug & Play
Enjoy your watching.
OK
If you want to reset this feature...
1. Press the
MENU button to display the menu.
Press the ▲ or ▼ button to select "Setup", then press the ENTER button.
2. Press the ENTER button again to select “Plug & Play”.
For further details on setting up options, refer to the pages 13~14.
The “Plug & Play” feature is only available in the TV mode.

Changing Channels

Using the Channel Buttons
1. Press the CH or CH button to change channels. When you press the CH or CH
sequence. You will see all the channels that the TV has memorized (The TV must have memorized at least three channels). You will not see channels that were either erased or not memorized. See page 16 to memorize channels.
Using the Number Buttons
Press the number buttons to go directly to a channel. For example, to select
1.
channel 27, press 2, then 7.
For quick channel change, press the number buttons, then press the ENTER
button.
button, the TV changes channels in
Enter
TV
Plug & Play Language : English Time V-Chip Caption Melody : Medium
Energy Saving : Off
SW Upgrade
Move Enter Return
Setup
English - 14
Using the Button
The button is used to select stations that broadcast a digital signal.
1.
For example, for Channel 7-1, press 7, then , then 1.
HD indicates the TV is receiving a Digital High Definition signal. SD indicates
the TV is receiving a Standard Definition signal.
For quick channel change, press the number buttons, then press the ENTER
button.
Using the PRE CH Button to select the Previous Channel
1. Press the PRE CH button. The TV will switch to the last channel viewed.
To quickly switch between two channels that are far apart, tune to one channel, then use the number button to select the second channel. Then use the PRE CH button to quickly alternate between them.

Adjusting the Volume

Using the Volume Buttons
1. Press the
Using the MUTE button At any time, you can cut off the sound using the MUTE button.
1. Press MUTE button and the sound cuts off. " " is displayed on the screen.
2. To turn mute off, press the MUTE button again or simply press the VOL or VOL button.
VOL or VOL button to increase or decrease the volume.

Viewing the Display

The display identies the current channel and the status of certain audio-video settings.
1. Press the INFO button on the remote control.
The TV will display the channel, the type of sound, and the status of certain picture and sound settings.
Press the INFO button once more or wait approximately 10 seconds and the
display disappears automatically.

Viewing the Menus

1. With the power on, press the MENU button.
The main menu appears on the screen. The menu’s left side has icons: Picture, Sound, Channel, Setup, Input.
2. Press the ▲ or ▼ button to select one of the icons.
Then press the ENTER
3. Press the EXIT button to exit.
The on-screen menus disappear from the screen after about one minute.
button to access the icon’s sub-menu.
English - 15
Air 7
Mono Picture Mode : Standard Sound Mode : Custom MTS : Stereo V-Chip : Off Caption : Off 5 : 54 pm
Mode : Standard Backlight Contrast 95 Brightness 45 Sharpness 50 Color 50 Tint G 50 R 50
▼ More
Move Enter Exit
PictureTV
7

Using the TOOLS Button

You can use the Tools button to select your frequently used functions quickly and easily. The “Tools” menu changes depending on which external input mode you are viewing.
Press the TOOLS button.
1.
The “Tools” menu will appear.
2. Press the ▲ or ▼ button to select a menu.
3.
Press the ▲/▼/◄/►/ENTER buttons to display, change, or use the selected items.For a more detailed description of each function, refer to the corresponding page.
Picture Mode ◄ Standard ►
Sound Mode : Custom Sleep Timer : Off Add to Favorite Switch to Air
Tools
• Picture Mode, see page 19
• Sound Mode, see page 24
• Sleep Timer, see page 39
• Add to Favorite, see page 30
Move Adjust Exit
• Switch to Air, see page 16
• Auto Adjustment, see page 35

Memorizing the Channels

Your TV can memorize and store all of the available channels for both "off-air" (Air) and "Cable" channels. After the available channels are memorized, use the CH or CH button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding or deleting channels (Channel Lists).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an Air or a Cable system).
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the ENTER
button.
TV
Antenna : Air Auto Program
Clear Scrambled Channel
Channel List Name Fine Tune
Signal Strength
Channel
► ►
2. Press the ENTER button to select “Antenna”.
Press the ▲ or ▼ button to select “Air” or “Cable”, then press the ENTER button. Press the EXIT
button to exit.
Easy Setting
1. Press the
Press the ▲ or ▼ button to select “Switch to Air” (or “Switch to Cable”), then press
2.
TOOLS
button on the remote control.
the ENTER button.
English - 16
Move Enter Return
TV
Antenna : Air
Auto Program
Clear Scrambled Channel
Channel List Name Fine Tune
Signal Strength
Move Enter Return
Picture Mode : Standard Sound Mode : Custom Sleep Timer Off Add to Favorite Switch to Air
Move Enter Exit
Channel
Air
Cable
Tools
Storing Channels in Memory (Automatic Method)
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select “Channel”, then press the ENTER button.
2. Press the ▲ or ▼ button to select "Auto Program", then press the ENTER
3.
Press the ▲ or ▼ button to select the antenna connection, then press the
button.
ENTER button.
Air: “Air” antenna signal.
Cable: “Cable” antenna signal. Auto: “Air” and “Cable” antenna signals.
When selecting the Cable TV system:
4.
Press the ENTER button to start the auto program.
Press the ◄ or ► button, then press the ▲ or ▼ to select the correct analog signal
cable system source among “STD”, “HRC”, and “IRC”. Press the ENTER button. If you have Digital cable TV, select the cable system signal source for both Analog and Digital.
STD, HRC and IRC identify various types of cable TV systems. Contact your
local cable company to identify the type of cable system that exists in your particular area. At this point the signal source has been selected.
The TV begins memorizing all available stations.
5.
After all the available channels are stored, it start to remove scrambled channels(see page 28).
If you want to stop Auto Programming, press the ENTER button. The “Stop
Auto Program?” message will be displayed. Select “Yes” by pressing the ◄ or ►
button, then press the ENTER button.
Press the EXIT
button to exit.
TV
Antenna : Air Auto Program
Clear Scrambled Channel
Channel List Name Fine Tune
Signal Strength
TV
Selects the antenna to execute the Auto Program function.
Air Cable Auto
TV
Selects a cable signal type for your location.
STD
HRC IRC
STD
HRC IRC
Auto Program in Progress. DTV Cable : -- Cable : 11
Enter Return
Removing scrambled channel.
Enter Return
Stop Auto Program? DTV Cable : -- Cable : 11
Yes
Move Enter Return
Auto Program is completed. 99 Channels are memorized.
DTV Cable : 65, Cable : 34
Enter Return
Channel
Move Enter Return
Auto Program
Start Start Start
Move Enter Return
Move Enter Return
Auto Program
analog
digital
Move Enter Return
Move Enter Return
Auto Program
Plug & Play
Auto Program
Plug & Play
Auto Program
Auto Program
Auto Program
Stop
Stop
OK
Start
Cable 50
11 %
DTV Cable 40
11 %
11 %
No
► ►
English - 17

To Select the Source

Use to select TV or other external input sources such as DVD players or Cable Box/ Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice.
1. Press the MENU button to display the menu. Press the▲ or ▼ button to select “Input”, then press the ENTER button.
2. Press the ENTER
Press the ▲ or ▼ button to select signal source, then press the ENTER
button to select "Source List".
button.
Available signal sources: TV, AV, Component1, Component2, PC, HDMI1,
HDMI2.
You can choose only those external devices that are connected to the TV.
Press the SOURCE button on the remote control to view an external signal source.

To Edit the Input Source Name

Name the device connected to the input jacks to make your input source selection easier.
1. Press the MENU button to display the menu.
Press the▲ or ▼ button to select “Input”, then press the ENTER button. Press the ▲ or ▼ button to select "Edit Name", then press the ENTER
button.
TV
Source List : TV Edit Name
Move Enter Return
TV
AV Component1 Component2 PC HDMI1 HDMI2
Move Enter Return
TV
Source List : TV Edit Name
Input
Source ListTV
: ---­: ---­: ---­: ---­: ---­: ----
Input
2. Press the ▲ or ▼ button to select "AV", "Component1", "Component2", "PC", "HDMI1", "HDMI2" input jack, then press the ENTER
button.
3. Press the ▲ or ▼ button to select “VCR”, “DVD”, “Cable STB”, “Satellite STB”,
“PVR STB”, “AV Receiver”, “Game”, “Camcorder”, “PC”, “TV”, “IPTV”, “Blu-Ray”, “HD DVD”, “Digital Media Adapter” input source, then press the ENTER button. Press the EXIT button to exit.
English - 18
Move Enter Return
Edit NameTV
AV : ----
Component1 : ---­Component2 : ---­PC : ---­HDMI1 : ---­HDMI2 : ----
Move Enter Return
AV : ----
Component1 : ---- Component2 : ---- PC : ---- HDMI1 : ---- HDMI2 : ----
Edit NameTV
----
VCR DVD Cable STB Satellite STB PVR STB AV Receiver Game
Move Enter Return
► ► ► ► ►

Picture Control

Changing the Picture Standard

You can activate either Dynamic, Standard, Movie by making a selection from the menu.
1. Press the MENU button to display the menu. Press the ENTER
2. Press the ENTER
Press the ▲ or ▼ button to select the “Dynamic”, “Standard” or “Movie”.
Dynamic: Selects the picture for high-denition in a bright room.Standard: Selects the picture for the optimum display in a normal environment.  Movie: Selects the picture for viewing movies in a dark room.
button, to select “Picture”.
button to select "Mode".
3. Press the EXIT button to exit.
Easy Setting
1. Press the
TOOLS
button on the remote control.
2. Press the ▲ or ▼ button to select “Picture Mode”.
3. Press the ◄ or ► button to select the required option.
4. Press the EXIT or
TOOLS
button to exit.

Customizing the Picture Settings

Mode : Standard Backlight Contrast 95 Brightness 45 Sharpness 50 Color 50 Tint G 50 R 50
▼ More
Mode : Standard
Backlight Contrast 95 Brightness 45 Sharpness 50 Color 50 Tint G 50 R 50
▼ More
Move Adjust Exit
PictureTV
7
Move Enter Return
PictureTV
Dynamic
7
Standard
Movie
Move Enter Return
Tools
Picture Mode ◄ Standard ►
Sound Mode : Custom Sleep Timer : Off Add to Favorite Switch to Air
Your television has several setting options that allow you to control the picture quality.
1.
To select the desired picture mode, follow the “Changing the Picture Standard” instructions numbers 1 and 2.
2. Press the ▲ or ▼ button to select “Backlight”, “Contrast”, “Brightness”,
“Sharpness”, “Color” or “Tint”, then press the ENTER button.
3. Press the ◄ or ► button to decrease or increase the value of a particular item.
Press the ENTER button.
Press the EXIT
When you make changes to “Backlight”, “Contrast”, “Brightness”, “Sharpness”,
button to exit.
“Color” or “Tint”, the OSD will be adjusted accordingly. In PC mode, you can only make changes to “Backlight”, “Contrast” and
“Brightness”.
Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Backlight: Adjusts the brightness of LCD back light.
Contrast: Adjusts the contrast level of the picture.
Brightness: Adjusts the brightness level of the picture.
Sharpness: Adjusts the edge definition of the picture.
Color: Adjusts color saturation of the picture.
Tint: Adjusts the color tint of the picture.
English - 19
Mode : Standard Backlight Contrast 95 Brightness 45 Sharpness 50 Color 50 Tint G 50 R 50
▼ More
Move Enter Return
Backlight
Move Adjust Return
PictureTV
7
7
Conguring Picture Options
Activating Picture Options
1. Press the MENU button to display the menu. Press the ENTER button, to select “Picture”.
Press the ▲ or ▼ button to select "Picture Options", then press the ENTER
2.
button.
Press the ▲ or ▼ button to select a particular item. Press the ENTER button. When you are satisfied with your setting, press the ENTER button. In PC mode, you can only make changes to the “Color Tone” and “Size” from
among the items in “Picture Options”.
▲ More
Picture Options Reset : OK
PictureTV
Move Enter Return
► ►
Setting the Color Tone
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2. (Refer to page 20)
2. Press the ▲ or ▼ button to select “Color Tone”, then press the ENTER button.
3. Press the ▲ or ▼ button to select “Cool2”, “Cool1”, “Normal”, “Warm1” or “Warm2”.
Press the ENTER button. “Warm1” or “Warm2” is only activated when the picture mode is “Movie”.
Settings can be adjusted and stored for each external device you have connected
to an input of the TV.
Setting the Screen Size
Occasionally, you may want to change the size of the image on your screen. Your TV comes with six screen size options, each designed to work best with specific types of video input. Your cable box or satellite receiver may have its own set of screen sizes as well. In general, though, you should view the TV in 16:9 mode as much as possible.
Follow the “Activating Picture Options” instructions numbers 1 and 2.
1.
(Refer to page 20)
2. Press the ▲ or ▼ button to select “Size”, then press the ENTER button.
3. Press the ▲ or ▼ button to select the screen format you want.
Press the ENTER button. Press the EXIT
16:9: Sets the picture to 16:9 wide mode.
Zoom1: Magnifies the size of the picture on the screen.
Zoom2: Magnifies the size of the picture more than “Zoom1”.
Wide Fit: Enlarges the aspect ratio of the picture to fit the entire screen.
4:3
Just Scan: Use the function to see the full image without any cutoff when
button to exit.
: Sets the picture to 4:3 normal mode.
HDMI (720p/1080i), Component (1080i) or DTV (1080i) signals are input.
Picture OptionsTV
Color Tone : Normal ► Size : 16:9 ► Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
Picture OptionsTV
Color Tone : Cool1
Size : 16:9 Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
Color Tone : Normal ► Size : 16:9 ► Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
16 : 9 Zoom1 Zoom2
Wide Fit
4 : 3
Just Scan
Move Enter Return
Cool2 Cool1
Normal
Warm1 Warm2
Picture OptionsTV
SizeTV
English - 20
Temporary image retention may occur when viewing a static image on the set for more than two hours.
After selecting “Zoom1”, “Zoom2” or “Wide Fit”:
Press the ◄ or ► button to select “Position”, then press the ENTER button. Press the ▲ or ▼ button to move the picture up and down.
Reset: Press the ◄ or ► button to select “Reset”, then press the ENTER button. You can initialize the setting.
After selecting “Just Scan” in HDMI (1080i) or Component (1080i) mode:
Press the ▲ or ▼ button to select “H-Position” or “V-Position”, then press the
ENTER button.
Press the ◄ or ► button to adjust the screen Position. Press the
ENTER button. Reset: Press the ▲ or ▼ button to select “Reset”, then press the ENTER
button. You can initialize the setting. HD (High Definition)
16:9 - 1080i (1920x1080), 720p (1280x720) Settings can be adjusted and stored for each external device you have connected to an input of the TV.
Input Source Picture Size
TV, Video, Component (480i, 480p) 16:9, Zoom1, Zoom2, 4:3 DTV(1080i), Component (1080i), HDMI (720p, 1080i) 16:9, 4:3, Wide Fit, Just Scan PC 16:9, 4:3
Alternately, you can press the P.SIZE button on the remote control repeatedly to
O
change the picture size.
16 : 9 Zoom1 Zoom2
Wide Fit
4 : 3
Just Scan
H-Position 0 V-Position 0 Reset
SizeTV
Position Reset
Adjust Enter Return
Just ScanTV
Move Enter Return
16:9
16:9 Sets the picture to 16:9 wide mode.
Wide Fit U Move
Wide Fit Enlarges the aspect ratio of the picture
to fit the entire screen.
Zoom1 U Move Zoom2 U Move
Zoom1 Magnifies the size of the picture on the
screen.
4:3 Just Scan
4:3 Sets the picture to 4:3 normal mode.
Zoom2 Magnifies the size of the picture more
than “Zoom1”.
Just Scan Use the function to see the full
image without any cutoff when HDMI (720p/1080i), Component (1080i) or DTV (1080i) signals are input.
English - 21
Setting the Digital Noise Reduction
If the broadcast signal received by your TV is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2. (Refer to page 20)
2. Press the ▲ or ▼ button to select "Digital NR", then press the ENTER button.
3. Press the ▲ or ▼ button to select "Off", "Low", "Medium", "High" or "Auto".
Press the ENTER button.
Off: Turns the screen noise reduction function off.  Low: Reduces screen noise at a low level.  Medium: Reduces screen noise at a medium level.  High: Reduces screen noise at a high level.  Auto: Automatically recognizes and reduces screen noise.
Press the EXIT button to exit.
Setting the HDMI Black Level
You can select the black level on the screen to adjust the screen depth.
1. Follow the “Activating Picture Options” instructions numbers 1 and 2.
(Refer to page 20)
2. Press the
▲ or ▼
button to select “HDMI Black Level”, then
press the ENTER button.
3. Press the
▲ or ▼
button to select “Normal” or “Low”, then press
the ENTER button.
Normal: The screen gets brighter.
Low: The screen gets darker.
This function is active only when an external device is connected to the TV via
HDMI. “HDMI Black Level” function may not be compatible with all external devices.
Press the EXIT button to exit.
Color Tone : Normal ► Size : 16:9 ► Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
Color Tone : Normal Size : 16:9
Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
TV
Color Tone : Normal ► Size : 16:9 ► Digital NR : Auto ► HDMI Black Level : Low
Film Mode : Off
Move Enter Return
TV
Color Tone : Normal Size : 16:9 Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
Picture OptionsTV
Picture OptionsTV
Off Low Medium High
Auto
Picture Options
Picture Options
Normal
Low
Setting the Film Mode
The TV can be set to automatically sense and process lm signals from all sources and
adjust the picture for optimum quality.
1.
Follow the “Activating Picture Options” instructions numbers 1 and 2. (Refer to page 20)
2. Press the ▲ or ▼ button to select "Film Mode", then press the ENTER
3. Press the ▲ or ▼ button to select "Off" or "Auto", then press the ENTER
button.
button.
Press the EXIT button to exit.
" Film mode" is supported in TV, VIDEO,COMPONENT(480i / 1080i) and
HDMI(480i / 1080i).
English - 22
TV
Color Tone : Normal ► Size : 16:9 ► Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
TV
Color Tone : Normal Size : 16:9 Digital NR : Auto
HDMI Black Level : Normal
Film Mode : Off
Move Enter Return
Picture Options
Picture Options
Off
Auto

Resetting the Picture Settings to the Factory Defaults

1. Press the MENU button to display the menu.
Press the ENTER
2. Press the ▲ or ▼ button to select "Reset", then press the ENTER Press the ▲ or ▼ button to select “OK” or “Cancel” then press the ENTER
button.
Press the EXIT Each mode can be reset.
button, to select “Picture”.
button to exit.
button.
▲ More
Picture Options
Reset : OK
PictureTV
OK
Cancel
Move Enter Return
English - 23

Sound Control

Changing the Sound Standard

You can select the sound mode to best suit the programming you’re watching.
1. Press the MENU button to display the menu. Press the
▲ or ▼
button to select "Sound", then press the ENTER
button.
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
SoundTV
► ►
► ►
2. Press the ENTER
Press the ▲ or ▼ button to select “Standard”, “Music”, “Movie”, “Speech”, or
button to select "Mode".
“Custom” sound setting, then press the ENTER button.
Press the EXIT
button to exit.
Standard: selects the normal sound mode.
Music: emphasizes music over voices.
Movie: provides the best sound for movies
Speech: emphasizes voice over other sounds.
Custom: recalls your customized sound settings.
(see “Customizing the Sound”)
Easy Setting
1. Press the
TOOLS
button on the remote control.
2. Press the ▲ or ▼ button to select “Sound Mode”.
3. Press the ◄ or ► button to select the required option.
4. Press the EXIT or
TOOLS
button to exit.

Customizing the Sound

The sound settings can be adjusted to suit your personal preference.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the ENTER
2. Press the ▲ or ▼ button to select "Equalizer", then press the ENTER
button.
button.
Move Enter Return
Mode : Custom
Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off TV Speaker : On
Picture Mode : Standard
Sound Mode ◄ Custom ►
Sleep Timer : Off Add to Favorite Switch to Air
Move Adjust Exit
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
SoundTV
Standard Music Movie Speech
Custom
Move Enter Return
Tools
SoundTV
► ►
3. Press the ◄ or ► button to select a particular frequency to adjust.
Press the ▲ or ▼ button to increase or decrease the level of the particular frequency.
Press the
ENTER
Press the EXIT
button.
button to exit.
L/R Sound Balance Adjustment: To adjust the sound balance of the L/R
speakers.
Bandwidth Adjustment (100Hz, 300Hz, 1KHz, 3KHz, 10KHz):
To adjust the
level of different bandwidth frequencies.
If you make any changes to the "Equalizer" settings, the sound mode is
automatically switched to the "Custom" mode.
English - 24
Move Enter Return
EqualizerTV
R
+
0
L
-
100Hz
300Hz 1KHz 3KHz 10KHzBalance
Move Adjust Return

Setting the TruSurround XT

TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the ENTER
button.
2. Press the ▲ or ▼ button to select "SRS TruSurround XT", then press the ENTER
3. Press the ▲ or ▼ button to select "Off" or "On", then press the ENTER
Press the EXIT
button.
button to exit.
TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc.
button.
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
Mode : Custom Equalizer
SRS TruSurround XT : Off
Multi-Track Options Auto Volume : Off TV Speaker : On
SoundTV
Move Enter Return
SoundTV
Off
On
► ►
TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Press the SRS button on the remote control to select "Off" or "On".
Move Enter Return

Choosing a Multi-Channel Sound (MTS) track - Digital

The digital-TV transmission system is capable of simultaneous transmission of many audio tracks (for example, simultaneous translations of the program into foreign languages). The availability of these additional “multitracks” depends upon the program.
"Multi-Track Options" is available only in TV mode.
Preferred Language
SoundTV
Move Enter Return
Multi-Track OptionsTV
: English
Multi-Track OptionsTV
: English
English
Spanish French
► ►
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the ENTER
button.
Quick way to access the MTS menu: Just press the “MTS” button on the remote
control. You can listen in a language other than your chosen language by pressing the MTS button.
2. Press the ▲ or ▼ button to select “Multi-Track Options", then press the ENTER
button.
3. Press the ENTER button to select “Preferred Language”.
Press the ▲ or ▼ button to choose the language (English, Spanish or French) you
want, then press the ENTER button. Press the EXIT
button to exit. “Preferred Language” is available only in Digital TV mode. You can only select the language from among the actual languages being broadcast.
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
Preferred Language
Multi-Track Sound : Stereo
Enter Return
Preferred Language
Multi-Track Sound : Stereo
You can listen in a language other than the Preferred language by pressing
the MTS button on the remote control.
English - 25
Move Enter Return

Choosing a Multi-Channel Sound (MTS) track - Analog

Multi-Track Sound
1. Press the MENU button to display the menu. Press the ▲ or ▼ button to select "Sound", then press the ENTER
2. Press the ▲ or ▼ button to select "Multi-Track Options", then press the ENTER
3.
Press the ▲ or ▼ button to select “Multi-Track Sound”, then press the ENTER
button.
button. Press the ▲ or ▼ button to select a setting you want, then press the ENTER button. Press the EXIT button to exit.
Mono: Choose for channels that are broadcasting in mono or if you are having
difficulty receiving a stereo signal.
Stereo: Choose for channels that are broadcasting in stereo.
SAP: Choose to listen to the Separate Audio Program, which is usually a
foreign-language translation.
“Multi-Track Sound” is available only in Analog TV mode. Depending on the particular program being broadcast, you can listen to “Mono”,
“Stereo” or “SAP”.
Press the MTS buttons on the remote control repeatedly to select “Mono”,
“Stereo” or “SAP”.
button.
Multi-Track OptionsTV
Preferred Language
Multi-Track Sound : Stereo
Enter Return
Preferred Language
Multi-Track Sound : Stereo
: English
Multi-Track OptionsTV
: English
Mono
Stereo
SAP
Move Enter Return

Automatic Volume Control

Reduces the differences in volume level among broadcasters.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the ENTER
2. Press the ▲ or ▼ button to select "Auto Volume", then press the ENTER
3. Press the ▲ or ▼ button to set Auto Volume "Off" or "On" then press the
ENTER Press the EXIT
button.
button to exit.
button.
button.
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options
Auto Volume : Off
TV Speaker : On
SoundTV
Move Enter Return
SoundTV
Off
On
Move Enter Return
► ►
English - 26

Setting the TV Speakers On/Off

Sound output from the TV speakers is muted.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Sound", then press the ENTER
2. Press the ▲ or ▼ button to select "TV Speaker", then press the ENTER
button.
button.
3. Press the ▲ or ▼ button to select “Off”, then press the ENTER button. Press the EXIT
button to exit.
When “TV Speaker” is set to “Off”, Sound menus except “Multi-Track Options”
cannot be adjusted.
The VOL , VOL and MUTE buttons do not operate when the "TV Speaker" is set to “Off”.
TV's Internal Speakers Audio Out (Optical, L/R Out) to Sound System
TV Speaker On
TV Speaker Off
Video No Signal
RF AV
Speaker Output Speaker Output Speaker Output Sound Output Sound Output Sound Output
Mute Mute Mute Sound Output Sound Output Sound Output
Mute Mute Mute Mute Mute Mute
Component, PC, HDMI
RF AV
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.
Mode : Custom
Equalizer SRS TruSurround XT : Off
Multi-Track Options
Auto Volume : Off TV Speaker : On
Mode : Custom Equalizer SRS TruSurround XT : Off Multi-Track Options Auto Volume : Off
TV Speaker : On
SoundTV
Move Enter Return
SoundTV
Off
On
Move Enter Return
Component, PC, HDMI
► ►
English - 27

Channel Control

Clearing Scrambled Channels - Digital

The Clear Scrambled Channel function is used to lter out scrambled channels after Auto Program is completed. This process may take up to 20~30 minutes.
1. Press the MENU button to display the menu.
Press the ▲ or ▼ button to select "Channel", then press the ENTER
button.
2. Press the ▲ or ▼ button to select "Clear Scrambled Channel", then press the
ENTER button. It searches scrambled channels, which are to be removed from the list.
To stop searching scrambled channels: Press the ENTER button to select Stop. Press the ◄ button to select "Yes", then press the ENTER button.
3.
When the scrambled channel searching is completed, press the ENTER button.
Press the EXIT
This function is only available in “Cable” mode.
button to exit.
TV
Antenna : Cable Auto Program Clear Scrambled Channel Channel List
Name Fine Tune
Signal Strength
Clear Scrambled Channel
Removing scrambled channel.
Enter Return
Channel
Move Enter Return
Plug & Play
DTV Cable 40
35 %
Stop
► ► ►
► ►
English - 28
Loading...
+ 98 hidden pages