Samsung LH46UDEBLBB/EN Quick Start Guide

Quick Setup Guide

Reverse Side

OUT

CONTROL IN

(MAGICINFO)

DVI IN

1 Receives the remote control signal via the external sensor board

and outputs the signal via LOOP OUT.

2 Supplies power to the external sensor board or receives the light

sensor signal.

DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable. MAGICINFO: To use MagicInfo, make sure to connect the DP-DVI cable.

UD46E-A UD46E-C UD46E-B UD55E-B

The colour and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Download the user manual from the website for further details. http://www.samsung.com/displaysolutions

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

BN6807319J02

7 8

9 0

! @

OUT

HDMI IN 1

HDMI IN 2

DP IN

RGB IN

(LOOPOUT)

DP OUT

AUDIO

RS232C

USB

RJ45

4 Connects to a source device using an HDMI cable.

5 Connects to a PC using a DP cable.

6 Connects to a source device using a D-SUB cable.

7 Connects to another product using a DP cable.

8 Receives sound from a PC via an audio cable.

9 Connects to the audio of a source device.

0 Connects to MDC using an RS232C adapter.

! Connect to a USB memory device. (Only for update purpose)

@ Connects to MDC using a LAN cable.

Checking the Components

- Contact the vendor where you purchased the product if any components are missing.

- The pictures may look different from the actual components.

Warranty card

Quick Setup Guide

MagicInfo Software

DVD

Remote Control DP cable RS232C(IN) adapter

AUDIO adapter

(Not available in some

locations)

Power cord

Holder-Ring (4EA) /

Screw (4EA)

Regulatory guide

Batteries

(Not available in some

locations)

External sensor KIT

1 Aim the remote control towards this spot on the LCD Display.

- Keep the area between the remote sensor and remote control obstacle-free.

Automatically detects the intensity of ambient light around a

selected display and adjusts the screen brightness.

The power indicator will turn off when the product is turned on. It will blink in power-saving mode.

Use this button for turning the LCD Display on and off.

5 Switches from PC mode to Video mode.

Selects the input source that an external device is connected to.

108&3

Troubleshooting Guide

Issues Solutions

The screen keeps switching on and off.

No Signal is displayed on the screen.

Not Optimum Mode is displayed.

The images on the screen look distorted.

The screen is not clear. The screen is blurry.

The screen appears unstable and shaky.

There are shadows or ghost images left on the screen.

The screen is too bright. The screen is too dark.

Check the cable connection between the product and PC, and ensure the connection is secure.

Check that the product is connected correctly with a cable.

Check that the device connected to the product is powered on.

This message is displayed when a signal from the graphics card exceeds the product’s maximum resolution and frequency.

Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to the product specifications.

Check the cable connection to the product.

Adjust Coarse and Fine.

Remove any accessories (video extension cable, etc) and try again.

Set the resolution and frequency to the recommended level.

Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product. Then, change the screen settings if required by referring to the Additional Information on the product menu and the Standard Signal Mode Table.

Adjust Brightness and Contrast.

Issues Solutions

White does not really look white.

The product will turn off automatically.

Go to Picture and adjust the White Balance settings.

Go to System and make sure Sleep Timer is set to O.

If a PC is connected to the product, check the power status of the PC.

Make sure the power cable is connected properly to the product and power outlet.

If the signal from a connected device is not detected, the product automatically turns off after 10 to 15 minutes.

There is no sound.

Check the connection of the audio cable or adjust the volume.

Check the volume.

The volume is too low.

Adjust the volume.

If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound card or software programme.

The remote control does not work.

Make sure that the batteries are correctly in place (+/-).

Check if the batteries are flat.

Check for power failure.

Make sure that the power cord is connected.

Check for any special lighting or neon signs switched on in the vicinity.

Connecting to a PC

RGB IN

AUDIO IN

DP IN

RJ45

RS232C IN

RS232C OUT

RS232C IN

RS232C OUT

RS232C IN

RS232C OUT

RJ45

HUB

Connecting the LAN Cable

Use Cat7(*STP Type) cable for the connection. *Shielded Twist Pair

Specifications

Model Name UD46E-A UD46E-C UD46E-B UD55E-B

Size 116.8 cm 116.8 cm 116.8 cm 138.7 cm

Panel

Display area

Dimensions (W x H x D)

1018.08 mm (H) x

572.67 mm (V )

1022.1 x 576.6 x

97.4 mm

1018.08 mm (H) x

572.67 mm (V )

1024 x 578.6 x

113.6 mm

1018.08 mm (H) x

572.67 mm (V )

1022.1 x 576.6 x

97.4 mm

1209.6 mm (H) x

680.4 mm (V )

1213.5 x 684.3 x

96.6 mm

DVI IN (MAGICINFO)

AUDIO IN

HDMI IN 1, HDMI IN 2

AUDIO IN

HDMI IN 1, HDMI IN 2

Connecting an External Monitor

To use old and new models together, rst contact the dealer the product was purchased from to check if they are compatible.

DP OUT (LOOPOUT)

Connecting to MDC

Weight (without Stand) 16.2 kg 16.2 kg 16.2 kg 21.5 kg

Horizontal Frequency 30 – 81 kHz, 30 – 134 kHz (DisplayPort), 30 – 90 kHz (HDMI)

Synchronization

Vertical Frequency 48 – 75 Hz, 56 – 75 Hz (DisplayPort), 24 – 75 Hz (HDMI)

RGB Analogue, DVI (Digital Visual Interface) Compliant Digital RGB

Resolution

Maximum Pixel Clock 148.5 MHz (Analogue, Digital), 594 MHz (Displayport, HDMI)

Power Supply

Environmental considerations

- This device is a Class A digital apparatus.

Optimum resolution 1920 x 1080 @ 60 Hz

Maximum resolution 1920 x 1080 @ 60 Hz, 3840 x 2160 @ 60 Hz (HDMI1, HDMI2, DP)

AC 100 to 240 VAC (+/- 10%), 60 / 50 Hz ± 3 Hz Refer to the label at the back of the product as the standard voltage can vary in dierent countries.

Operating

Storage

Temperature: 0 ˚C - 40 ˚C (32 ˚F - 104 ˚F) Humidity: 10 % - 80 %, non-condensing

Temperature: -20 ˚C - 45 ˚C (-4˚F - 113˚F) Humidity: 5 % - 95 %, non-condensing

Connecting to a Video Device

Connecting to an Audio System

HDMI IN 1, HDMI IN 2

AUDIO IN

HDMI IN 1, HDMI IN 2

AUDIO OUT

RJ45

RS232C OUT

RS232C IN

RS232C OUT

RS232C IN

RS232C OUT

(For India Only) This product is RoHS compliant. For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers 18002668282, 180030008282.

Contact SAMSUNG WORLD WIDE

Web site: http://www.samsung.com

INDIA

1800 3000 8282 - Toll Free 1800 266 8282 - Toll Free

For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.