Samsung LH46OMNSLGB/EN User Manual
Smart Signage User Manual (By Model)
This manual provides information about your Smart Signage including supported types and product specications per model.
OMN (OM46N OM55N)
OMN-D (OM55N-D)
The colour and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Trademarks other than Samsung Electronics are
property of their respective owners.
Table of contents
Preparations
Checking the Components 3
Ports 4
OM46N/OM55N 4
OM55N-D 5
Anti-theft Lock 6
Before Installing the Product (Installation
Guide) 7
OM46N/OM55N 7
OM55N-D 8
Installing the Wall Mount 11
Installing the Wall Mount 11
Wall Mount Kit Specifications (VESA) 11
Specifications
General 12
Preset Timing Modes 13
Appendix
Licence 15
2
Chapter 01
Preparations
"Contact the vendor where you
purchased the product if any
components are missing.
"The appearance of the components
may differ from the images shown.
"A stand is not provided with the
product. To install a stand, you can
purchase one separately.
"Use either the back-side magnet or
the double-sided tape depending
on where you want to attach the
external ambient light sensor.
The warranty for adhesiveness of the
double-sided tape applies to rsttime-use only.
"The external ambient light sensor is
marked with the label on the sensor
cable.
Checking the Components
Quick Setup Guide
Batteries (AAA x 2)
(Not available in some locations)
(Not available in some locations)
Warranty card
Remote Control External ambient light sensor
Regulatory guide Power cord
External IR cable
(OM46N, OM55N x 1 / OM55N-D
x 2)
Power IN rubber
(Supported model: OM55N-D)
HOLDER-GUIDE x 2 / Screw (M3
x L6) x 4
(Supported model: OM55N-D)
Top cover
(Supported model: OM55N-D)
3
Ports
"
The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Port Description
OM46N/OM55N
RS232C
OUT / IN
AUDIO OUT
IR IN
AMBIENT
SENSOR IN
USB
LAN OUT
LAN IN
HDMI 1 IN
HDMI 2 IN
DP IN
Stick the receiver of an external IR
cable to this location when the cable
is not used or the product is moved.
Air outlet
Air inlet
RS232C OUT
RS232C IN
AUDIO OUT
IR IN
AMBIENT SENSOR IN
USB
¨
LAN OUT
LAN IN
HDMI 1 IN
HDMI 2 IN
DP IN
HDMI OUT
Connects to MDC using an RS232C adapter.
Outputs sound to an audio device via an audio cable.
Connects to an external IR cable that receives signals from the remote control.
Used to supply power to the external sensor board and to receive signals from
the ambient light sensor.
Connect to a USB memory device.
• Wired LAN connection port used to connect an external device such as a
laptop to connect to the Internet.
• Connects to MDC using a LAN cable. (10/100 Mbps)
Connects to MDC using a LAN cable. (10/100 Mbps)
Connects to a source device using a HDMI cable or HDMI-DVI cable.
Connects to a PC using a DP cable.
Connects to another product using a HDMI cable.
HDMI OUT
4
OM55N-D
"
The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
"
Install this product for indoors only. Install the display labelled OUTDOOR in the direction of the window.
Port Description
Air outlet
Air inlet
RS232C IN
IR IN
USB
¨
HDMI IN
LAN
AMBIENT SENSOR IN
Connects to MDC using an RS232C adapter.
Connects to an external IR cable that receives signals from the remote control.
Connect to a USB memory device.
Connects to a source device using a HDMI cable or HDMI-DVI cable.
• Wired LAN connection port used to connect an external device such as a
laptop to connect to the Internet.
• Connects to MDC using a LAN cable. (10/100 Mbps)
Used to supply power to the external sensor board and to receive signals from
the ambient light sensor.
Setting up Device ID
OM55N-D model has separate remote sensors on the front and back sides.
Depending on the distance from the remote control or other surrounding conditions, it is possible both front and
back displays respond to the remote control signal. You can assign IDs to displays (INDOOR: 1, OUTDOOR: 2) and
follow the steps below to restrict remote control to one selected display only.
"
To reverse the remote controlled display after setting otherwise, first cancel the existing ID settings for the
INDOOR and OUTDOOR displays by pressing the UNSET button.
• To select the INDOOR display only
1) Position the remote control facing the INDOOR IR sensor and press SET → 1 → E on the control.
2) Position the remote control facing the OUTDOOR IR sensor and press SET → 1 → E on the control.
• To select the OUTDOOR display only
1) Position the remote control facing the INDOOR IR sensor and press SET → 2 → E on the control.
2) Position the remote control facing the OUTDOOR IR sensor and press SET → 2 → E on the control.
5
Loading...