Samsung DVD-V6700 User Manual [nl]

DVD-V6700

www.samsung.com/za

User’s Manual

Gebruiksaanwijzing

0000_V6700_xfa_Eng1 3/8/07 9:44 AM Page 1

Safety Instructions

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 2

The following illustrations represent precautions.

The lightning bolt is a warning sign alerting you to dangerous voltage inside the product.

DO NOT OPEN THE DVD-VCR. Refer to service personnel.



DO NOT expose the DVD-VCR to extreme temperature conditions



DO NOT expose the DVD-VCR to direct sunlight.

DO NOT expose the DVD-VCR to any liquids.



(below 5°C and above 40°C) or to extreme humidity conditions (less than 10% and more than 75%).



DO NOT place any objects on the DVD-VCR or remote control.

During a storm and/or lightning, unplug the DVD-VCR from the mains jack and aerial.



If the remote control is not used for a long period of time, remove the batteries and store it in a cool, dry place.

THIS DEVICE IS NOT FOR USE IN INDUSTRIAL ENVIRONMENTS

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembling is prohibited.

1.Apparatus shall not be exposed to dripping or splashing and no objects filled with uids, such as vases, shall be placed on the apparatus.

2 The Mains plug is used as a disconnect device and shall stay readily operable at any

time.

2 -

English

- 3

Disc Type and Characteristics

Disc Markings

• CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time.

• Video with CD sound, VHS quality & MPEG-1 compression technology.

- DO NOT play CD-ROM, CD-I and DVD-ROM in this player! (CDGs play audio only, not graphics).

- It may not play CD-R,CD-RW and DVD-R, -RW, DVD+R, +RW in all cases due to the type of disc or condition of the recording.

- The recorded disc may not run as playback depends on the recording speed.

- Do not run the player with two discs loaded at the same time.

PAL

DIGITAL

SOUND

STEREO

NTSC

Play Region Number

Both the DVD-VCR and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not be played.

The Region Number for this player is described on the rear panel of the player.

Disc Types (Logos)

Recording Types

Disc Size Max. Playing Time Characteristics

Single-sided 240 min. Double-sided 480 min.

Audio

Video

VIDEO-CD

AUDIO-CD

DVD

• DVD contains excellent sound and video due to Dolby Digital and MPEG-2 system.

• Various screen and audio functions can be easily selected through the on-screen menu.

74 min.

Audio

Video

Audio

This DVD-VCR is capable of playing the following types of discs with the corresponding logos :

Play Region Number.

Stereo disc.

Dolby Digital disc.

Digital Audio disc.

NTSC broadcast system in U.S.A, Canada, Korea, Japan, etc.

PAL colour system in Europe, Australia, New Zealand, etc.

DTS disc.

20 min.

74 min.

20 min.

Single-sided 80 min. Double-sided 160 min.

12 Cm

8 Cm

12 Cm

8 Cm

12 Cm

8 Cm

Disc contains a Divx software product.

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 3

4 -

English

Getting Started

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Disc Type and Characteristics . . . . . . . . . . . . . . . . . . . . . . .3

Overviews . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Front View of the DVD-VCR (DVD-V6700) . . . . . . . . . . .5

Rear View of the DVD-VCR (DVD-V6700) . . . . . . . . . . . .5

Display Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Inserting Batteries in the Remote Control . . . . . . . . . . . . . . .6

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . . .6

Connections

Connecting DVD-VCR to the TV using the RF Cable . . . . 8

Connecting DVD-VCR to the TV using the

Audio/Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connecting DVD-VCR to the TV using the

S-Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting DVD-VCR to the TV using the

Component Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting to an AV amplifier with the digital

input jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting External Devices . . . . . . . . . . . . . . . . . . . . . . 11

Plug & Auto Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Settings

Tuning Your Television for the DVD-VCR . . . . . . . . . . . . . .13

Copying From DVD to VCR . . . . . . . . . . . . . . . . . . . . . . . . .13

Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . .14

Setting the Menu Language . . . . . . . . . . . . . . . . . . . . . . . .14

Presetting the Stations Automatically . . . . . . . . . . . . . . . . .15

Presetting the Stations Manually . . . . . . . . . . . . . . . . . . . . .16

Clearing a Preset Station . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Changing the Preset Station Table . . . . . . . . . . . . . . . . . . .17

Selecting the RF OUT Sound Mode (I-B/G-D/K) . . . . . . . . .18

Setting the VCR Output Channel . . . . . . . . . . . . . . . . . . . .18

VCR Functions

Selecting the Colour Mode . . . . . . . . . . . . . . . . . . . . . . . . .19

NICAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Intelligent Picture Control . . . . . . . . . . . . . . . . . . . . . . . . . .20

Auto Power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

Screen Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Selecting the Cassette Type . . . . . . . . . . . . . . . . . . . . . . . . 21

Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Selecting the Recording Speed . . . . . . . . . . . . . . . . . . . . . .22

Protecting a Recorded Cassette . . . . . . . . . . . . . . . . . . . . .22

Recording a Programme Immediately . . . . . . . . . . . . . . . . .22

Recording a Programme with Automatic Stop . . . . . . . . . .23

Recording from Another VCR or Camcorder . . . . . . . . . . . . . .23

Using the Assemble Edit Function . . . . . . . . . . . . . . . . . . .24

Using the Timer Programming Feature . . . . . . . . . . . . . . . .24

Checking a Preset Recording . . . . . . . . . . . . . . . . . . . . . . .25

Cancelling a Preset Recording . . . . . . . . . . . . . . . . . . . . . .26

Playing Back

Playing a Cassette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Adjusting Picture Alignment Manually . . . . . . . . . . . . . . . . .26

Selecting the Audio Output Mode . . . . . . . . . . . . . . . . . . . .27

Playing a Cassette in Slow Motion . . . . . . . . . . . . . . . . . . .27

Playing a Sequence Frame by Frame . . . . . . . . . . . . . . . .27

Playing a Sequence at Variable Speeds . . . . . . . . . . . . . . .27

Searching for a Specific Sequence . . . . . . . . . . . . . . . . . . .28

Using the Tape Counter . . . . . . . . . . . . . . . . . . . . . . . . . . .29

DVD Functions

Setting Up the Language Features . . . . . . . . . . . . . . . . . . .30

Setting Up the Audio Options . . . . . . . . . . . . . . . . . . . . . . .31

Setting Up the Display Options . . . . . . . . . . . . . . . . . . . . . .32

Setting Up the Parental Control . . . . . . . . . . . . . . . . . . . . . .33

DivX(R) Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

Special Playback Features . . . . . . . . . . . . . . . . . . . . . . . . .36

Using the Display Function . . . . . . . . . . . . . . . . . . . . . . . . .37

Adjusting the Aspect Ratio (EZ View) . . . . . . . . . . . . . . . . .38

Selecting the Subtitle Language . . . . . . . . . . . . . . . . . . . . .39

Selecting the Audio Language . . . . . . . . . . . . . . . . . . . . . . .39

Changing the Camera Angle . . . . . . . . . . . . . . . . . . . . . . . .39

Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Repeat Chapter/Title . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

A to B Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

MP3/WMA Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42

Program & Random Play (CD/MP3/WMA) . . . . . . . . . . . . . . . .43

Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

DivX/MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Divx/MPEG4 Special Playback Features . . . . . . . . . . . . . .46

Reference

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Troubleshooting Guide (VCR) . . . . . . . . . . . . . . . . . . . . . . .49

Troubleshooting Guide (DVD) . . . . . . . . . . . . . . . . . . . . . . .50

Contents

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 4

English

- 5

1. DVD DECK.

2. OPEN/CLOSE BUTTON.

3. VIDEO CASSETE COMPARTMENT.

4. EJECT BUTTON.

5. STANDBY/ON BUTTON.

6. LINE IN 2 VIDEO INPUT JACK.

7. LINE IN 2 AUDIO L/R INPUT JACK.

8. PROGRESSIVE SCAN MODE BUTTON.

9. FRONT PANEL DISPLAY.

10. PROGRAMME SELECTION BUTTON.

11. DVD/VCR SELECTION BUTTON.

12. COPY BUTTON.

13. RECORD BUTTON.

14. REWIND/SKIP BACK BUTTON.

15. STOP BUTTON.

16. PLAY/STILL BUTTON.

17. FAST FORWARD/SKIP NEXT BUTTON.

Front View of the DVD-VCR (DVD-V6700)

5 6 7 8 9 10 11 12 13 14 15 16 17

1 2 3 4

1. The DVD Deck is active.

2. Disc is loaded.

3. The time, counter position, current deck status is displayed.

4. VHS tape is inserted.

5. The VCR Deck is active.

6. A Timer Recording is programmed or in progress.

1 2 3 4 5

Rear View of the DVD-VCR (DVD-V6700)

Display Indicators

1. ANTENA INPUT

2. RF OUT TO TV

3. LINE IN 1 (Audio / Video)

4. LINE OUT (Audio / Video)

5. LINE AUDIO OUT (S-VIDEO OR COMPONENT)

6. DIGITAL AUDIO OUT (COAXIAL)

7. COMPONENT VIDEO OUT

8. DIGITAL AUDIO OUT (OPTICAL)

9. S-VIDEO OUT

2 4 6 8 9

1 3 5 7

Overviews

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 5

6 -

English

Make sure that the following basic accessories are supplied with your DVD-VCR.

You must insert or replace the batteries in the remote control when you:

• Purchase the DVD-VCR

• Find that the remote control is no longer

working correctly

1 To release the battery compartment cover,

push the tab in the direction of the arrow and lift up.

2 Insert two AAA, RO3 or equivalent batteries,

taking care to respect the polarities:

• + on the battery with + on the remote control.

• – on the battery with – on the remote control.

Do not mix different battery types (manganese

and alkaline for example).

3 Replace the cover by aligning it with the base

of the remote control and push it down.

Batteries for

remote controls

Remote Control

Audio & Video

Cable

RF-Cable

Owner’s

Instructions

Accessories

Inserting Batteries in the Remote Control

Tour of the Remote Control

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 6

English

- 7

1. DVD,VCR

Used to operate DVD, VCR.

2. STANDBY/ON

Used to turn the power on or off.

3. Number buttons

4. TIMER

Used to activate the timer recording of a programme.

5. REC ( ● )

Used to make a recording on cassette.

6. SKIP ( / )

Use to skip a title, chapter or track.

7. STOP ( ■ )

Used to stop during playback.

8. AUDIO

Used to access various audio functions.

9. TRK ( / )

Used to adjust picture alignment manually to obtain the best possible picture during playback.

10. MENU

Used to display the on-screen menu.

11. OK

/ ,¥/ 

Used to control the cursor in the on-screen menu and confirm your choice.

12. EZ VIEW

Used to adjust the aspect ratio on a disc.

13. DISC MENU

Used to display a disc menu.

14. SUBTITLE

Used to change the DVD’s subtitle language.

15. ANGLE

Used to access various camera angles on a DVD.

IPC (Intelligent Picture Control). Used to adjust the sharpness of the picture.

16. INPUT SEL.

Used to select a external input signal.

17. TV/VCR

18. INFO.

Used to display the current setting or disc status.

19. OPEN/CLOSE

Used to open and close the disc and video cassette tray.

20. SHUTTLE

Used to play a sequence at variable speeds.

21. F.ADV/STEP

Used to advance a sequence frame by frame.

22. SPEED

Used to select the recording speed.

23. PLAY/PAUSE ( )

Used to play or pause during playback.

24. SEARCH ( / )

Used to search forward or backward through a disc.

25. PROG

(

)

Used to select a TV programme.

26. RETURN

Used to return to a previous menu.

27. ZOOM

Used to enlarges picture .

28. CLEAR

Used to clear a preset TV station. Used to cancel a preset recording. Used to cancel a preset mark. Used to set the tape counter to zero. Used to resume normal play during repeat play.

29. MARK

Used to mark a position during playback a disc.

Used to search for a specific sequence.

30. MODE

Used to select the programme or random play.

REPEAT

Used to allow the repeat play a title, chapter, track, disc or A-B.

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 7

8 -

English

To receive television programmes a signal must be received from one of the following sources:

• An outdoor aerial

• An indoor aerial

• A cable television network

• A satellite receiver

1 Remove the aerial or network input cable

from the television.

2 Connect this cable to the 75Ω coaxial jack

marked on the rear of your DVD-VCR.

3 Plug the RF Cable supplied into the jack

on your DVD-VCR.

4 Plug the other end of the RF Cable into the

connector previously used for the aerial on the television.

You can connect your DVD-VCR to the television using the Audio/Video cable if the appropriate input is available on the television. You thus:

• Obtain better quality sound and pictures

• Simplify the setting up procedure of your DVD-VCR

1 Connect the RF Cable.

2 Connect one end of the Audio/Video cable

to the Video output and Audio L, R output jack on the rear of the DVD-VCR.

3 Plug the other end into the appropriate

connector on the television.

ANT IN

Aerial

Aerial cable

RF cable

• Make sure that both the television and the

DVD-VCR are switched off before connecting the cables.

Note

Connecting DVD-VCR to the TV using the Audio/Video Cable

Connecting DVD-VCR to the TV using the RF Cable

RF cable

Aerial cable

Aerial

• Regardless of the type of connection chosen,

you must always connect the RF Cable supplied. Otherwise, no picture will be visible on the screen when the DVD-VCR is switched off.

• Make sure that both the television and the

DVD-VCR are switched off before connecting the cables.

Notes

CConnections

onnections

Yellow

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 8

English

- 9

COMPONENT VIDEO IN

COMPONENT INPUT

COMPONENT VIDEO OUT

Connecting DVD-VCR to the TV using the S-Video Cable

Connecting DVD-VCR to the TV using the Component Video Cable

Your TV must support progressive scan input to allow you to watch component video output. You will enjoy high quality accurate colour reproduction images. Component video seperates the picture element into black and white(Y), blue(Pb), red(Pr) signals to present most clear and clean images.

1 Connect Component video cables between

the COMPONENT VIDEO OUT jacks on the rear of the DVD-VCR and COMPONENT

VIDEO IN jacks on the rear of the TV.

2 Connect audio cables between the AUDIO

LINE OUT jacks on the rear of the DVD-VCR

and AUDIO IN jacks on the rear of the TV.

• Take care to respect the colour coding of the left and right channels.

You will enjoy high quality images. S-Video seperates the picture element into black and white(Y) and colour(C) signals to present clearer images than regular video input mode.

1 Connect one end of the S-Video cable into

the S-VIDEO output jack on the rear of the DVD-VCR.

2 Plug the other end of the S-Video cable into

the appropriate input connector on the televi-

sion.

3 Connect one end of the audio cables supplied

into the AUDIO LINE output jacks on the rear

of the DVD-VCR.

• Take care to respect the colour coding of the left and right channels.

4 Plug the other end of the audio cables into the

appropriate input connectors on the televisio

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 9

10 -

English

To take full advantage of the movie theater experience that DVD offers, you may want to connect your DVD-VCR to a complete Surround Sound system, including an A/V Receiver and six Surround Sound speakers. If your A/V receiver is equipped with a Dolby Digital Decoder, you have the option to bypass the DVD-VCR’s built-in Dolby Digital Decoder. Use the Digital Audio Out connection below. To enjoy Dolby Digital or DTS sound, you must set up the audio settings. (See page 30)

1 Connect a Digital Audio coaxial/optical cable

from the Digital Audio Out jacks on the panel of the DVD-VCR to their corresponding Digital Audio Input jacks on your A/V Receiver:

To Digital Audio Input of an A/V

Receiver with a Dolby, MPEG2, DTS,

Digital Decoder

Connecting to an AV amplifier with the digital input jack

Progressive Scan (DVD only)

If the TV connected supports Progressive Scan, press the P.SCAN button on the front panel in stop mode.

• The message “Press OK to confirm Progressive scan mode. Otherwise press RETURN.” will be displayed. If you want Progressive scan mode, select OK. Make sure that the disc has stopped completely before changing the mode.

• To cancel the progressive scan mode, press

the P.SCAN button in stop mode.

• Do not press the P.SCAN button if you are using a

TV that does not support Progressive mode. Nothing will be displayed on the screen if pressed. To release the Progressive mode, press the P.SCAN button in stop mode.

• See your TV User’s Manual to find out if your TV

supports Progressive Scan.If Progressive Scan is supported, follow the TV User’s instructions regarding Progressive Scan settings in the TV’s menu system.

•

Depending on your TV, the method of connection may differ from the illustration above.

• What is "Progressive Scan"? Progressive scan has

twice as many scanning lines as the interlace output method has. Progressive scanning method can provide better and clear erpicture quality.

• You must connect the player to the component(s)

before using the Progressive Scan feature.

• Make sure that the colour coded connections

match. That is, the Y, Pb and Pr component output jacks of your DVD -VCR should be connected to the exact corresponding component input jacks on your TV. Otherwise, red or blue images will be displayed on the TV screen.

•

NTSC DVD disc is not supported.

Notes

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 10

English

- 11

This allows you to connect your DVD -VCR to other external devices and view or record their outputs.

• Method 1 : Connecting a VCR, Set-Top Box(STB) or DVD-VCR to the AUDIO/VIDEO LINE IN 1 jacks.

• Method 2 : Connecting a Camcorder to the LINE

IN 2

in jacks.

You can use the LINE IN 2 jacks on the front panel of the DVD-VCR. You can record from connected equipment.

When an input source is inserted into LINE IN 2 while viewing TV, the input will be switched to LINE IN 2 automatically.

Connecting External Devices

•

You can also use the LINE IN 2 jacks on the front panel of the DVD-VCR.

• When the S-Video jack and Video jack are both

connected, the S-Video jack will have priority. Line Selection will be automatically done

• Copy protected content cannot be recorded.

Notes

Method 1 : Connecting a VCR, set-top Box (STB) Or DVD-VCR to

the AUDIO/VIDEO LINE IN 1 jacks

Method 2 : Connecting a Camcorder to the LINE IN 2 jacks

Connecting a VCR or external device to AUDIO/VIDEO LINE IN 1 jacks of the DVD-VCR.

You can record from connected equipment (VCR, STB or DVD).

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 11

12 -

English

5 Start the auto scanning.

The number of stations automatically stored by the DVD-VCR depends on the number of stations that it has found.

6 Check the date and time.

Refer to “Setting the Date and Time” to change the date and time. (see page: 14)

Plug & Auto Setup

Your DVD-VCR will automatically set itself up when it is plugged into the mains for the first time. TV stations will be stored in memory. The process takes a few minutes. Your DVD-VCR will then be ready for use.

1 Connect the RF Cable as indicated on page

8. (Connecting Your DVD-VCR to the TV using the RF Cable)

2 Plug the DVD-VCR into the mains.

• “AUTO” in the front panel display flickers.

3 The Language Set menu is displayed.Press

the  or  button move selection bar to select the desired laguange then press OK button.

4 Press the  or  button to select the

desired language, then press OK button.

Start the auto setup.

Auto Setup will be

started.

Check antenna and TV

cable connection.

RETURN MENU

Please Wait

10%



RETURN MENU

Auto Setup

• Now, you only have to switch the DVD-VCR on and it is ready for use.

• Function for “Plug & Auto Set Up” is fixed already. So if you want to change this fixed one, you can change. (refer to “Presetting the Stations Manually” page 16).

Notes

OK RETURN MENU

Language Set

SETUP

VCR

PROG

FUNC

DVD

OK RETURN MENU

Clock Set

Time Date Year

12 : 00 01 / JAN / 2007 MON



English

Français

Deutsch

Español

Italiano

Nederlands

кЫТТНЛИ

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 12

English

- 13

The DVD-VCR allows you to copy the contents of a DVD to a VHS tape with a press of the COPY button.

If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not permitted to copy Macrovision® encoded DVDs.

1 Insert the disc you wish to copy in the DVD

deck and close the drawer.

2 Insert a blank VHS videotape into the VCR

deck.

Press the COPY button on the DVD-VCR front panel.

•

The DVD will go into Play mode and the VCR

will go into Record mode.

•

If the DVD disc menu appears, you may need to press the PLAY button manually to begin copying.

4 When the DVD is finished playing, press the

VCR button on the remote control and then press the STOP button to end the copy.

• You must stop the Copy process manually when the DVD movie ends or the DVD may replay and record over and over again.

Tuning Your Television for the DVDVCR

You must tune your television for the DVD-VCR only if you are using the RF cable. To view pictures from your DVD-VCR when a Scart cable is used, the television must be set to the audio/video mode (AV).

1 Switch on the television.

2 Switch on the DVD-VCR by pressing the

/I STANDBY/ON on the front of the DVD-

VCR or STANDBY/ON on the remote control.

3 Select a programme position on the television

to be reserved for use with your DVD-VCR.

4 Insert the video cassette in the DVD-VCR.

Check that the DVD-VCR starts reading the cassette; if not, press the II button.

5 Start a scan on your television or set the tele-

vision to UHF channel 36.

6 Fine tune the television until the pictures and

sound are obtained clearly.

7 When the picture and sound are perfectly

clear, store this channel at the desired programme position on the television. That programme is now reserved for use with your DVD-VCR.

SSettings

ettings

Copying From DVD to VCR

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 13

14 -

English

Setting the Menu Language

1 Press the MENU button, then press the OK or

 button.

2 Press the OK or  button again.

The Language Set menu is displayed.

3 Press the  or  button to select desired

language, then press the OK or  button.

• Press the MENU button to exit the menu.

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

Your DVD-VCR contains a 24-hour clock and calendar used to:

• Automatically stop programme recording.

• Preset your DVD-VCR to record a programme automatically.

You must set the date and time when:

• You purchase the DVD-VCR.

• Do not forget to reset the time when you change clocks from winter to summer time and vice versa.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Clock,

then press the OK or  button. The Clock Set menu is displayed.

3 Press the ¥ or  button to select the hour,

minutes, day, month, and year. The selected option is highlighted. Press the  or  button to set them. The day of the week is displayed automatically. Press the OK button.

• You can hold down the  or button to

scroll more quickly through the values.

• Press the MENU button to exit the menu.

Setting the Date and Time

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

RETURN

Clock Set

SETUP

VCR

PROG

FUNC

DVD

Time Date Year

12 : 00 01 / JAN / 2007 SUN

OK RETURN MENU

Language Set



English

Français

Deutsch

Español

Italiano

Nederlands

кЫТТНЛИ

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 14

English

- 15

4 Press the OK button A mesagge is displayed,

indicating that any cannels already preset on your DVD-VCR will be delete.

5 Press the OK button to start the auto scanning.

The message Please Wait is displayed.

• The first frequency band is scanned and stored, then the DVD-VCR searches for the second station and so on. When the automatic scanning procedure has finished, the DVD-VCR switches automatically to programme 1.

• If you wish to cancel the auto scanning before the end, press the MENU button

• The number of stations automatically stored by the DVD-VCR depends on the number of stations that it has found.

• Once the auto scanning procedure has finished, some stations may have been stored more than once; select the stations with the best reception and delete the ones no longer required (refer to page 17).

Please Wait

10%



RETURN MENU

Auto Setup

Notes

You do not need to preset the stations if you have already set them automatically (refer to “Plug & Auto Set Up” on page 12).

Your DVD-VCR contains a built-in tuner used to receive television broadcasts. You must preset the stations received through the tuner. This can be done:

• Plug & Auto Set up (refer to page 12)

• Automatically

• Manually (refer to page 16)

You can store up to 80 stations.

1 Press the MENU button, then press the OK

or  button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

Presetting the Stations Automatically

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



System Selection

System - B/G

System - D/K

System - I

3 Press the OK or  button. The System

Selection is displayed. Press the /

buttons to select your system.

OK RETURN MENU

Your data will be lost

Press OK to continue

MENU to exit

Auto Setup

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 15

16 -

English

You do not need to preset the stations manually if you have already set them automatically.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

3 Press the  or  button to select Manual

Setup, then press the OK or  button. The TV STATION TABLE menu is displayed.

4 Press the  or  button to select the

required programme number.

Presetting the Stations Manually

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

5 Press the  button to preset the station.

The MANUAL TUNING menu will be displayed. Press the ¥ or  button to start scanning the channels. The frequency band is scanned and the first station found is displayed.

6 If necessary, press the  or  button to

select MFT, then press the ¥ or  button to adjust the picture.

7 Press the  or  button to select NAME.

The station name is set automatically from the broadcast signal.

• To change the programme’s name, press

the  button. The first letter of the name flashes.

Repeat this procedure from step 4 onwards,

until all the required stations have been stored.

10 Press the MENU button to exit the menu.

Select a character in the name.

Move to the next previous or character

Press the  or button until the required character is displayed (letters, numbers or “-” character).

Press the ¥ or  button respectively.

To... Then...

If you... Then...

Wish to store the station displayed

Do not wish to store the station displayed

•

Press OK to store the station.

•

Press the  or button until the CH is selected.

•

Press the ¥ or  button to go on scanning the frequency band and display the next station.

❉ ❉ MANUAL TUNING. ❉ ❉

SYSTEM : I

PR : 1

CH : 021

MFT : -

NAME : - - - -

¥¥

MEMORY : OK

RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME SYSTEM

1 021 - - - -



SWAPPING : OK

DELETE : CLEAR RETURN

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 16

English

- 17

Changing the Preset Station Table

You can rearrange the station table and give different programme numbers to the stations listed according to your own preferences.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

3 Press the  or button to Select Manual

Setup, then press the OK or  button. The TV STATION TABLE menu is displayed.

4 preset TV station. The selected station is dis-

played at the same time on the television screen.

5 Press the OK button to change the

programme number assigned to a station.

6 Press the  or  button to select required

position, then press the OK button to swap the position. For example to move a TV station in programme 1 to programme 3.

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



If you have stored a TV station:

• That you do not require

• At the wrong programme position, you can cancel it.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

3 Press the  or button to select Manual

Setup, then press the OK or  button.

The TV STATION TABLE menu is displayed.

4 Press the  or  button to select required

preset TV station. Press the CLEAR button to delete.

5 Repeat the same procedure from step 4

onwards until all the required stations have

Clearing a Preset Station

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME SYSTEM

1 021 - - - - I



SWAPPING : OK

DELETE : CLEAR RETURN

❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME SYSTEM

1 021 - - - - I



SWAPPING : OK

DELETE : CLEAR RETURN

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 17

18 -

English

Your DVD-VCR output channel may need to be changed if the pictures suffer from interference or if your TV cannot find the pictures.

1 Press the MENU button, then press the OK

or  button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

3 Press the  or  button to select VCR

Output CH.

4 Press the OK or ¥ or  button to select the

required output channel .

➝ CH21 ➝ ..CH36 ➝ ..CH69

• Press the MENU button to exit the menu.

Then tune your television again (see page 13)

• You can select the required output channel directly by using the number button.

You can choose the sound mode (I,B/G or D/K) according to the TV set connected to your VCR.

1 Press the MENU button, then press the OK

or  button.

2 Press the  or  button to select Install,

then press the OK or  button. The Install menu is displayed.

3 Press the  or button to select TV

System, then press the OK or  button to

select I,G or K.

• Press the MENU button to exit the menu.

Setting the VCR Output Channel

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

Selecting the RF OUT Sound Mode (I-B/G-D/K)

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

Install

RETURN MENU

Auto Setup



Manual Setup



TV System : I



VCR Output CH : CH 36



❉ ❉ TV STATION TABLE ❉ ❉

PR CH NAME SYSTEM

3 021 - - - - I

 

SWAPPING : OK

DELETE : CLEAR RETURN

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 18

English

- 19

NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound. Please refer to page 27.

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select User Set,

then Press the OK or  button. The User Set menu is displayed.

3 Press the  or  button to select NICAM, then

press the OK or  button to select On or Off.

• On (for NICAM mode):

Normally set at this position

• Off (for MONO mode):

Only set at this position to record the standard mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.

NICAM

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

User Set

Colour System : Auto



NICAM : ON



IPC : ON



Before recording or playing back a cassette, you can select the required system standard. Otherwise, the system automatically selects the reception standard when you select AUTO.

• When playing back a cassette, the standard is automatically selected by the DVD-VCR.

• When you playback an NTSC-recorded tape on this DVD-VCR make a setting on the colour system according to your TV. If your TV is a PAL system only TV, set NTPB. If your TV is multi system TV (NTSC 4.43 compatible), set NT4.43 and you can record NT4.43.

1 Press the MENU button, then press the OK

or  button.

2 Press the  or  button to select User Set,

then press the OK or  button. The User Set menu is displayed.

3 Press the OK or button to select required

colour system.

Auto ➝ PA L ➝ MESECAM➝ B/W

• Auto: When playing back a cassette,

the system standard is automatically selected by the DVD-VCR.

• B/W: Black and White

Selecting the Colour Mode

VVCR

CRFF

unctions

SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

User Set

Colour System : Auto



NICAM : ON



IPC : ON



0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 19

20 -

English

Intelligent Picture Control

This feature allows you to adjust the sharpness of the image automatically, according to your own preferences.

1 During playback, press the MENU button,

then press the OK or  button.

2 Press the  or  button to select User Set,

then press the OK or  button. The User Set menu is displayed.

3 Press the  or  button to select IPC

(Intelligent Picture Control), then press the OK or  button.

• You can select the modes simply by press-

ing the IPC button.

4 To adjust the sharpness manually, press the

 button to turn the IPC mode OFF. The sharpness of the picture is adjusted manually. Press the ¥ or  buttons until the picture is displayed according to your preferences.

❉ ❉ PICTURE ❉ ❉

IPC : OFF

SOFTEN SHARPEN

¥¥

ON/OFF :



❉

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

User Set

Colour System : Auto



NICAM : On



IPC : On



Auto Power Off

This feature automatically turns off your DVDVCR if no signal is received and you do not press any button for the selected time.

1 Press the MENU button, press the OK or 

button.

2 Press the  or  button to select Auto

Power Off.

3 Press the OK or  button to select the

preset interval.

➝ Off ➝ 1 Hour ➝ 2 Hour ➝ 3 Hour

• Press the MENU button to exit the menu.

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 20

English

- 21

You can set repeat play to repeat the tape continously from beginning to end.

1 Press the MENU button, then press the  or

 button to select VCR.

2 Press the OK or  button, then press the

or button to select Repeat Play.

Press the OK or  button to select On or Off.

• On: Repeat play.

• Off: Do not wish to repeat play.

Selecting the Cassette Type

If you wish to use the tape counter to display the time remaining on a cassette, you must indicate the type of cassette inserted.

1 Press the MENU button, then press the  or

 button to select VCR.

2 Press the OK or  button.

The Tape Select is highlighted.

3 Press the OK or  button to select the

correct cassette length.

➝ E180 ➝ E240 ➝ E260 ➝ E300

• Press the MENU button to exit the menu.

Repeat Play

SETUP

VCR

PROG

FUNC

DVD

RETURN

VCR Setup

Tape Select : E180



Repeat Play : Off



SETUP

VCR

PROG

FUNC

DVD

OK RETURN MENU

VCR Setup

Tape Select : E180



Repeat Play : Off



Screen Messages

Your DVD-VCR displays most information both the DVD-VCR and the television. You can choose to display or hide this information on the television screen (If you configure the Screen Message to Off, the Fast Forward and Rewind messages will not be displayed on the screen. However, the Search Message will not be displayed on the screen regardless of the Screen Message configuration).

1 Press the MENU button, then press the OK or

 button.

2 Press the  or  button to select Screen

Messages.

3 Press the OK or  button to select On or Off.

• On : Select to display on-screen information.

• Off : Select to hide on-screen information.

• Press the MENU button to exit the menu.

SETUP

VCR

PROG

FUNC

DVD

RETURN MENU

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



SETUP

VCR

PROG

FUNC

DVD

Setup

Language : English



Clock



Install



User Set



Auto Power Off : Off



Screen Messages : On



RETURN MENU

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 21

22 -

English

Selecting the Recording Speed

Video cassettes have a safety tab to prevent accidental erasure. When this tab has been removed, you cannot record on the tape.

1 If you wish to protect a cassette, break off the

tab using a small screwdriver.

2 To re-record over a protected cassette (safety

tab broken), cover the hole with adhesive tape.

You can record a cassette at two different speeds:

• SP (Standard Play)

• LP (Long Play) In Long Play modes:

• Each cassette lasts twice as long

• The recording is of a slightly lower quality

1 Press the SPEED button to select SP or LP.

• The selected record speed will appear on the front panel display.

Type Recording Time (in SP)

E180 180 mins. or 3 hours

E240 240 mins. or 4 hours

E260 260 mins. or 4 hours and 20 mins.

E300 300 mins. or 5 hours

Protecting a Recorded Cassette

Recording a Programme Immediately

Before recording a programme, you must have preset the corresponding station (unless you are recording via an external video source). If you have not done so, refer to pages 15~16.

1 Switch on the television.

2 Insert the video tape in to the VCR deck, with

the window visible and the safety tab intact or the opening covered with adhesive tape. The DVD-VCR is switched on automatically.

3 Select the station by pressing the PROG

( or ) button or select the source (LINE IN 1, LINE IN 2) by pressing the INPUT SEL. button for a satellite tuner or external video source. The station number is displayed and the programme can be seen on the television.

4 Select the recording speed by pressing the

SPEED button as many times as required

5 Hold down the REC (●) button for a while to

start recording. The record indicator appears on the television and DVD-VCR display. An index is recorded on the tape (Refer to page 28).

6 To stop recording, press the ■ button once.

• If your DVD-VCR ejects the cassette when you start recording, check to make sure that the cassette’s safety tab is intact or that the opening (Created by a broken safety tab) is overed with adhesive tape.

• If you reach the end of the tape while

recording, the cassette rewinds automatically.

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 22

English

- 23

Recording from Another VCR or Camcorder

You can copy a cassette to your DVD-VCR from another video source, such as another VCR or a Camcorder etc.

• It is an infringement of copyright laws to copy prerecorded cassettes or to re-record them in any form without the permission of the owners of the corresponding copyright.

1 Connect the output jack of your external

devices to the LINE IN 1 or LINE IN 2 on the front or rear of the DVD-VCR.

2 Insert a blank cassette in your DVD-VCR.

3 Insert the pre-recorded cassette in the other

video source (VCR or Camcorder etc).

4 Press the INPUT SEL. button to select the

appropriate input on your DVD-VCR:

• LINE IN 1, LINE IN 2 for the audio/video input.

5 Start playing back the cassette to be copied.

6 Hold down the REC (●) button for a while to

start recording on your DVD-VCR.

7 When you have finished recording, press the

■ button on both VCR and DVD-VCR.

• If you wish to view the cassette being copied, your DVD-VCR must be connected as usual to the television (Refer to page 8 for further details).

Recording a Programme with Automatic Stop

This function enables you to record up to nine hours (LP) of programmes.Your DVD-VCR stops automatically after the requested length of time.

1 Switch on the television.

2 Insert the cassette on which the programme

is to be recorded, with the window visible and the safety tab intact or the opening covered with adhesive tape. The DVD-VCR is switched on automatically.

3 Select the station to be recorded by pressing

the PROG( or ) button or select the source (LINE IN 1, LINE IN 2) by pressing the INPUT SEL. button for a satellite tuner or external video source. The station number is displayed and the programme can be seen on the television.

4 Select the recording speed by pressing the

SPEED button as many times as required

(Refer to page 22).

5 Hold down the REC (●) button for a while to

start recording. The record indicator appears on the television screen and DVD-VCR display. An index is recorded on the tape (Refer to page 28).

6 Press the REC (●) button several times to

increase the recording time in:

• 30-minute intervals up to four hours.

• 1-hour intervals up to nine hours. The length is displayed on the television displays. The selected programme is recorded for the length of time requested. At the end of that time, the DVD-VCR stops recording automatically and power off.

7 If you wish to cancel the recording before the

end, press the STANDBY/ON button.

• If the end of the tape is reached while recording, the recording stops and power off.

LENGTH 2:30

SET LENGTH :

PRESS

REC

●

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 23

24 -

English

Using the Assemble Edit Function

This function allows you to start a new recording at a specific position on the cassette while maintaining a very smooth scene change.

1 Insert the cassette to be edited in your

DVD-VCR.

2 Press the ll button to start playback.

3 When you reach the position from which you

wish to start the new recording, press the ll button.

4 Press the F.ADV/STEP button as often as

necessary to advance frame by frame, until the exact recording position is located.

5 While the DVD-VCR is in still mode, hold

down the REC (●) button for a while to acti- vate the assemble edit function. The mode is changed to pause.

6 Select the source from which you wish to

record by pressing:

• The PROG or button for television

channels.

• The INPUT SEL. button for the LINE IN 1,

LINE IN 2 input source.

7 Press the ll button to start recording.

If you want to finish the recording, press the

■ button.

Using The Timer Programming Feature

The Timer Programming feature allows you to preset the DVD-VCR to record a programme up to one month before that programme is to be broadcast. Up to six programmes can be preset.

• Before presetting a recording, check that the Date and Time are correct.

• You must check that the cassette tape is loaded.

1Press the MENU button, then press the  or

 button to select PROG.

2 Press the OK or  button. The timer pro-

gramming menu is displayed.

3 Press the OK or  button to select PR, then

press the or button to select the required station.

• Press the INPUT SEL. button to select an

input source (LINE IN 1, LINE IN 2) other then the tuner.

4 Press the  button to select Day, then press

the  or  button to select the required day.

RETURN

SETUP

VCR

PROG

FUNC

DVD

Timer Method

If you want to set the

timer program, press

theOKkey.

PR Day Start Stop Speed

RETURN MENU

01 MO 01

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 24

English

- 25

9 Press the MENU button to exit the menu.

10 Press the STANDBY/ON button to activate

the timer.

Before starting recording, the DVD-VCR compares the timer duration with the remaining time on the cassette.

You can check your preset recordings:

• When you have finished presetting the DVDVCR

• If you have forgotten which programmes will be recorded.

1 Press the MENU button, then press the  or

 button to select PROG.

The Timer Method menu is displayed.

2 Press the OK or button. The list of preset

recodings is displayed with the corresponding information.

• It can be displayed simply by pressing the

TIMER button on the remote control.

3 To change any values, select the required

programme by pressing the  or  button, then change any values as required. For more details refer to page 24. (Step 2 to 9).

• Press the MENU button to exit the menu.

Checking a Preset Recording

SETUP

DVD

VCR

PROG

FUNC

RETURN

Timer Method

If you want to set the

timer program, press

theOKkey.

PR Day Start Stop Speed

RETURN MENU

01 MO 01 13 : 25 19 : 57 SP

-- -- -- --:-- --:-- --

• DLY : Daily

• W-SU : Weekly Sunday

• W-MO Weekly Monday

• W-SA Weekly Saturday

• MO 01 : Monday 01

5 Press the  button to select Start (Start time

of recording).

6 Press the  button to select Stop (Recording

stop time).

• Press the ¥ or  button to select the hour

or minute.

• Press the  or  button to set the stop

time.

7 Press the  button to select Speed

(Recording speed).

• Press the or  button to select the

required recording speed.

• Auto ➝ SP (Standard Play) ➝ LP (Long

Play)

• Auto Tape Speed Select

The DVD-VCR’s “Auto Tape Speed Select” function compares the duration of the timer recording to the actual recording time remaining on the tape loaded. If there is insufficient tape to complete a timer recording in Auto mode, the DVD-VCR automatically switches to LP mode to record the whole programme.

8 When you have finished, press the OK button

to set the Timer Programming.

PR Day Start Stop Speed

RETURN MENU

01 MO 01 13 : 25

PR Day Start Stop Speed

RETURN MENU

01 MO 01 13 : 25 19 : 57 SP

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 25

26 -

English

Cancelling a Preset Recording

You can cancel any programmes that are:

• Incorrect

• No longer required

1 Press the MENU button, then press the  or

 button to select PROG . The Timer

Method menu is displayed.

2 Press the OK or button. The list of preset

recodings is displayed with the corresponding information.

• It can be displayed simply by pressing the

TIMER button on the remote control.

3 Press the  or  button to select the

programme to be cancelled,then press the CLEAR button .

• All the recording information is deleted and broadcast will not be recorded.

• Press the MENU button to exit the menu.

RETURN

SETUP

VCR

PROG

FUNC

DVD

Timer Method

If you want to set the

timer program, press

theOKkey.

PR Day Start Stop Speed

RETURN MENU

-- -- -- --

-- --:-- --

This function allows you to play any prerecorded cassette.

1 Switch on both the television and your

DVD-VCR.

2 If the safety tab on the cassette is removed,

the cassette is played automatically.

• When a cassette is loaded, the tape position is optimized automatically to reduce disturbance (Digital Auto Tracking).

• When playing a cassette, if the end of the tape is reached, the cassette is rewound automatically. NTSC tapes can be played back but cannot be recorded with this DVDVCR.

3 Press the ■ (stop) button to stop the

playback. Press the (eject) button to eject the playback.

This feature allows you to adjust the alignment manually to obtain the best possible picture. When noise bars or streaks appear during playback, adjust alignment manually by pressing the TRK ( or ) button until the picture is clear and stable.

• The tracking bar appears.

• The image is adjusted.

Playing a Cassette

Adjusting Picture Alignment Manually

PPlaying Back

laying Back

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 26

English

- 27

You can select the mode in which the sound is reproduced on the loudspeakers and AV outputs. The following options are available. Press the AUDIO button on the remote control until the required option is displayed.

Option Description

L Used to listen to the sound on the left Hi-Fi channel.

R Used to listen to the sound on the right Hi-Fi

channel.

MIX Used to listen to the mixed sound of the Hi-Fi and

normal channels.

MONO Used to listen to the sound on the normal mono

channel.

LR Used to listen to Hi-Fi stereo sound on the left

and right channels

• When playing back tapes recorded in Hi-Fi, the sound switches to Hi-Fi after five seconds of Mono.

➝ L ➝ R ➝ MIX ➝ MONO ➝ LR

You can play a cassette in slow motion.

• No sound is heard when playing back a cassette in slow motion.

1 Press the :

• ll button to start playing the cassette.

• ll button again to make still mode.

•  button to start slow mode.

• ¥¥ or  button as many times as

required to decrease or increase the speed respectively.

• ll button twice to return to the normal

speed.

• The slow motion feature does not support running video backwards.

2 When playing back in slow motion, picture

interference may occur. Press the TRK ( or ) button to minimize this effect.

• When you have been using the Slow Motion function for more than about two minutes, the DVD-VCR will automatically play to protect the:

- Cassette.

- Video heads.

Selecting the Audio Output Mode

Playing a Cassette in Slow Motion

Playing a Sequence Frame by Frame

You can vary the playback speed using the Shuttle function (up to nine times the normal speed). Example: You wish to analyse a sports person’s technique, movement by movement.

• No sound is heard when playing a sequence at variable speeds.

1 Press the :

• ll button to start playing the cassette.

• SHUTTLE (<<) button to play the cassette

backwards.

• SHUTTLE (>>) button to play the cassette

forwards.

2 Each time you press the SHUTTLE button,

the speed is changed as shown in the following illustration.

You can

• Stop the cassette at a given frame (image)

• Advance one frame at a time

No sound is heard when playing back frame by frame.

1 Press the :

• ll button to start playing the cassette.

• ll button again to make still mode.

• F.ADV button to advance frame by frame.

• ll button to return to normal playback.

• Vertical stability: When playing back frame by frame, interference may be seen on the screen. Press the TRK ( or ) button to minimize this effect.

REVERSE

PLAY

REVERSE

PLAY

REVERSE

PLAY

STILL

SLOW

MOTION

X1/10

SLOW

MOTION

X1/5

PLAY

PLAYX3PLAYX5PLAY

Playing a Sequence at Variable Speeds

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 27

28 -

English

Searching for a Specific Sequence

Each time you record a cassette on this DVDVCR, an “index” is automatically marked on the tape when recording starts. The Search function allows you to fast-forward or rewind to a specific index and start playback from that point. Depending on the direction selected, the indexes are numbered as follows:

• This DVD-VCR uses a standard indexing system (VISS). As a result, it will recognize any indexes marked by other VCRs using the same system and vice versa.

Go To [0:00:00] Stop

Use this feature when you want to search for the 0:00:00 counter position on a cassette. Press the CLEAR button at the point on the tape where you want to set the counter to 0:00:00. The VCR will rewind or fast forward, searching for the 0:00:00 counter position, and then automatically stop at that position.

1 Press the MENU button, then press the  or

 button to select FUNC. The Function

menu is displayed. Press the OK or  button.

2 Press the  or  button to select VCR

Function, then press the OK or  button.

The VCR Function menu is displayed with the Go To [0:00:00] selected.

• It can be displayed simply by pressing the

SEARCH button.

etc.

21 1 2

etc.

Prev Seq.

Seq. being

played

Next Seq.

➔

SETUP

DVD

VCR

PROG

FUNC

VCR Function

Go To [0:00:00]

End Search

Intro Scan

OK RETURN MENU

3 Press the OK or  button again.

End Search

Use this feature when you want to search for a blank position to record a program on a cassette. The VCR will fast forward, searching for a blank position, and then automatically stop at that position. If the VCR reaches the end of the tape during end search, the tape will be ejected.

1 Press the SEARCH button. The VCR

Function menu is displayed. Press the  or  button to select End Search.

2 Press the OK or  button.

Intro Scan

1 Press the SEARCH button.

The VCR Function menu is displayed. Press the  or  button to select Intro Scan.

2 Press the OK or  button.

3 Press the ¥¥ or  button depending on

the direction where your desired programme is located.

SETUP

DVD

VCR

PROG

FUNC

VCR Function

Go To [0:00:00]

End Search

Intro Scan

OK RETURN MENU

INTRO SCAN : ¥¥ 

SETUP

DVD

VCR

PROG

FUNC

VCR Function

Go To [0:00:00]

End Search

Intro Scan

OK RETURN MENU

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 28

English

- 29

Index Skip Search

This feature will enable you to fast forward/rewind to a specific point on a tape: e.g. If you have recorded 3 different programmes on a tape and you have rewound the tape to the beginning, by using this feature you can go directly to the start of programme 2 simply by pressing the SEARCH button.

1 Press the SEARCH button.

The VCR Function menu is displayed. Press the orbutton to select Intro Scan.

2 Press the OK or  button.

3 Press the ¥¥ or  button twice more.

4 These Index searches can be made forwards

(press the  button) or backwards (press the ¥¥ button). (¥¥ -20

● ●

+20 )

This will take you directly to the start of the desired programme is located.

To cancel an Index search simply press the

ll or ■ button.

SETUP

DVD

VCR

PROG

FUNC

VCR Function

Go To [0:00:00]

End Search

Intro Scan

OK RETURN MENU

INDEX SEARCH : ¥¥ -06

4 When an Index mark is found the DVD-VCR

will playback the tape for 5 seconds, after which it will continue searching for the next Index mark

5 If you want to watch the tape from a

particular Index, press the 

ll button twice.

INTRO SCAN : ¥¥

The tape counter:

• Indicates the elapsed time in the play and record modes (Hours, Minutes and Seconds).

• Is reset when a cassette is inserted in the DVD-VCR.

• Allows you to find the beginning of a sequence easily.

• If the remaining time is to be calculated correctly, you must indicate the type of cassette being used.

1 Insert a cassette in your DVD-VCR.

To set the tape counter to zero at the beginning of a sequence:

• Press the INFO button twice to display the

counter.

• Press the CLEAR button when you want to

set the tape counter to zero.

2 When you are ready,

• Start Playback or Recording.

• Press the ■ button.

• To fast-froward or rewind to the sequence at which the counter was set to zero, press the ¥¥ or  button.

• Some DVD-VCR information, such as the counter, can be displayed on the television screen (Unless you have deactivated the Screen Messages mode; refer to page 21).

Press the INFO button:

• Once to display the current function, programme number, recording speed, time and counter.

• Twice to display the counter only.

• Three times to display the time remaining on the cassette.

• Four times to clear the display.

Using the Tape Counter

0:00:00

0000_V6700_xfa_Eng1 1/31/07 2:51 AM Page 29

30 -

English

Setting Up the Language Features

DDVD

VD FF

unctions

If you set disc menu, audio and subtitle language in advance, it will come up automatically every time you watch a movie.

Using the Disc Menu Language

1 Press the MENU button in the stop mode.

Press the  or  button to select DVD, then press the OK or button.

2 Press the OK or button again.

Press the  or button to select Disc

Menu, then press the OK or  button.

3 Press the  or  button to select the

required language.

• Select Others if the language you want is

not listed.

Language Setup

OK RETURN MENU

Disc Menu Language



English

Français

Deutsch

Español

Italiano

Nederlands

Others

Disc Menu

Disc Menu : English



Audio : English



Subtitle : English



Using the Audio Language

1 Press the MENU button in the stop mode.

Press the  or  button to select DVD, then press the OK or button.

2 Press the OK or button again.

Press the  or button to select Audio, then press the OK or button.

3 Press the  or  button to select the

required language.

• Select Original if you want the default

soundtrack language to be the original language the disc is recorded in.

• Select Others if the language you want is

not listed.

4 Press the OK button.

OK RETURN MENU

Audio Language



English

Français

Deutsch

Español

Italiano

Nederlands

Original

Others

Audio

Language Setup

OK RETURN MENU

Disc Menu : English



Audio : English



Subtitle : English



SETUP

DVD

VCR

PROG

FUNC

OK RETURN MENU

DVD Setup

Language Setup



Audio Setup



Display Setup



Parental Setup :



Divx (R) Registration



SETUP

DVD

VCR

PROG

FUNC

OK RETURN MENU

DVD Setup

Language Setup



Audio Setup



Display Setup



Parental Setup :



Divx (R) Registration



0000_V6700_Xfa_Eng2 1/31/07 2:52 AM Page 30

+ 77 hidden pages