Samsung DVD-E135, DVD-E217, DVD-E218, DVD-E219, DVD-E317 Service Manual

DVD PLAYER

Chassis : Exino [Slim]
DVD-E217/E218/E219
DVD-E317/E318/E319
DVD-E135/E535
DVD-P213/P313
DVD-E2323

SERVICE

1. Precautions

2. Alignment and Adjustment

3. Exploded Views and Parts List

4. Electrical Parts List

5. Block Diagram

6. Schematic Diagrams

Manual

DVD PLAYER CONTENTS

SERVICE MANUAL

DVD-E217/E218/E219/E317/E318/E319/E135/E535/P213/P313/E2323

ELECTRONICS

© Samsung Electronics Co., Ltd. AUG. 2003

Printed in Korea

AK82-00388A

If you want to know additional information which is not included on this Service Manual, please refer to the
DVD-E234 Training Manual (AK82-00314A).

This Service Manual is a property of Samsung Electronics Co.,Ltd.
Any unauthorized use of Manual can be punished under applicable
international and/or domestic law.

Samsung Electronics 1-1

1. Precautions

1-1 Safety Precautions

1) Before returning an instrument to the customer,
always make a safety check of the entire instrument,
including, but not limited to, the following items:

(1) Be sure that no built-in protective devices are

defective or have been defeated during servicing.
(1)Protective shields are provided to protect both
the technician and the customer. Correctly replace
all missing protective shields, including any
removed for servicing convenience.
(2)When reinstalling the chassis and/or other as­sembly in the cabinet, be sure to put back in place
all protective devices, including, but not limited to,
nonmetallic control knobs, insulating fish papers,
adjustment and compartment covers/shields, and
isolation resistor/capacitor networks. Do not oper­ate this instrument or permit it to be operated with­out all protective devices correctly installed and
functioning.

(2) Be sure that there are no cabinet openings through

which adults or children might be able to insert
their fingers and contact a hazardous voltage. Such
openings include, but are not limited to, excessive­ly wide cabinet ventilation slots, and an improper­ly fitted and/or incorrectly secured cabinet back
cover.

(3) Leakage Current Hot Check-With the instrument

completely reassembled, plug the AC line cord
directly into a 120V AC outlet. (Do not use an iso­lation transformer during this test.) Use am leakage
current tester or a metering system that complies
with American National Standards institute (ANSI)
C101.1 Leakage Current for Appliances and
Underwriters Laboratories (UL) 1270 (40.7). With
the instrument’s AC switch first in the ON position
and then in the OFF position, measure from a
known earth ground (metal water pipe, conduit,
etc.) to all exposed metal parts of the instrument
(antennas, handle brackets, metal cabinets, screw­heads, metallic overlays, control shafts, etc.), espe­cially any exposed metal parts that offer an electri­cal return path to the chassis.

Any current measured must not exceed 0.5mA.
Reverse the instrument power cord plug in the out­let and repeat the test. See Fig. 1-1.

Any measurements not within the limits specified
herein indicate a potential shock hazard that must
be eliminated before returning the instrument to
the customer.

Fig. 1-1 AC Leakage Test

(4) Insulation Resistance Test Cold Check-(1) Unplug

the power supply cord and connect a jumper wire
between the two prongs of the plug. (2) Turn on the
power switch of the instrument. (3) Measure the
resistance with an ohmmeter between the
jumpered AC plug and all exposed metallic cabinet
parts on the instrument, such as screwheads,
antenna, control shafts, handle brackets, etc. When
an exposed metallic part has a return path to the
chassis, the reading should be between 1 and 5.2
megohm. When there is no return path to the chas­sis, the reading must be infinite. If the reading is
not within the limits specified, there is the possibil­ity of a shock hazard, and the instrument must be
repaired and rechecked before it is returned to the
customer. See Fig. 1-2.

Fig. 1-2 Insulation Resistance Test

DEVICE
UNDER

TEST

(READING SHOULD

NOT BE ABOVE

0.5mA)

LEAKAGE
CURRENT

TESTER

EARTH

GROUND

TEST ALL

EXPOSED METER

SURFACES

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

2-WIRE CORD

Antenna
Terminal

Exposed
Metal Part

ohm

ohmmeter

Precautions

1-2 Samsung Electronics

2) Read and comply with all caution and safety re­lated notes on inside the cabinet, or on the chassis.

3) Design Alteration Warning-Do not alter or add to
the mechanical or electrical design of this instru­ment. Design alterations and additions, including
but not limited to, circuit modifications and the
addition of items such as auxiliary audio output
connections, might alter the safety characteristics of
this instrument and create a hazard to the user. Any
design alterations or additions will make you, the
servicer, responsible for personal injury or property
damage resulting therefrom.

4) Observe original lead dress. Take extra care to
assure correct lead dress in the following areas:
(1) near sharp edges, (2) near thermally hot parts (be
sure that leads and components do not touch ther­mally hot parts), (3) the AC supply, (4) high voltage,
and (5) antenna wiring. Always inspect in all areas
for pinched, out-of-place, or frayed wiring, Do not
change spacing between a component and the
printed-circuit board. Check the AC power cord for
damage.

5) Components, parts, and/or wiring that appear to
have overheated or that are otherwise damaged
should be replaced with components, parts and/ or
wiring that meet original specifications.
Additionally, determine the cause of overheating
and/or damage and, if necessary, take corrective
action to remove any potential safety hazard.

6) Product Safety Notice-Some electrical and mechani­cal parts have special safety-related characteristics
which are often not evident from visual inspection,
nor can the protection they give necessarily be
obtained by replacing them with components rated
for higher voltage, wattage, etc. Parts that have spe­cial safety characteristics are identified by shading,
an ( )or a ( )on schematics and parts lists. Use
of a substitute replacement that does not have the
same safety characteristics as the recommended
replacement part might create shock, fire and/or
other hazards. Product safety is under review con­tinuously and new instructions are issued whenev­er appropriate.

Precautions

Samsung Electronics 1-3

1-2 Servicing Precautions

CAUTION : Before servicing units covered
by this service manual and its supplements, read and
follow the Safety Precautions section of this manual.

Note : If unforseen circumstances create conflict
between the following servicing precautions and any
of the safety precautions, always follow the safety pre­cautions. Remember: Safety First.

1-2-1 General Servicing Precautions

(1) a. Always unplug the instrument’s AC power cord

from the AC power source before (1) re-moving
or reinstalling any component, circuit board,
module or any other instrument assembly, (2)
disconnecting any instrument electrical plug or
other electrical connection, (3) connecting a test
substitute in parallel with an electrolytic capaci­tor in the instrument.

b. Do not defeat any plug/socket B+ voltage inter-

locks with which instruments covered by this
service manual might be equipped.

c. Do not apply AC power to this instrument and

/or any of its electrical assemblies unless all
solid-state device heat sinks are correctly in­stalled.

d. Always connect a test instrument’s ground lead

to the instrument chassis ground before connect­ing the test instrument positive lead. Always
remove the test instrument ground lead last.

Note : Refer to the Safety Precautions section ground
lead last.

(2) The service precautions are indicated or printed on

the cabinet, chassis or components. When servic­ing, follow the printed or indicated service precau­tions and service materials.

(3) The components used in the unit have a specified

flame resistance and dielectric strength.
When replacing components, use components
which have the same ratings. Components identi­fied by shading, by( ) or by ( ) in the circuit dia­gram are important for safety or for the characteris­tics of the unit. Always replace them with the exact
replacement components.

(4) An insulation tube or tape is sometimes used and

some components are raised above the printed
wiring board for safety. The internal wiring is
sometimes clamped to prevent contact with heat­ing components. Install such elements as they
were.

(5) After servicing, always check that the removed

screws, components, and wiring have been in­stalled correctly and that the portion around the
serviced part has not been damaged and so on.
Further, check the insulation between the blades of
the attachment plug and accessible conductive
parts.

1-2-2 Insulation Checking Procedure

Disconnect the attachment plug from the AC outlet
and turn the power ON. Connect the insulation resi­stance meter (500V) to the blades of the attachment
plug. The insulation resistance between each blade of
the attachment plug and accessible conductive
parts(see note) should be more than 1 Megohm.

Note : Accessible conductive parts include metal pan­els, input terminals, earphone jacks, etc.

Precautions

1-4 Samsung Electronics

1-3 ESD Precautions

Electrostatically Sensitive Devices (ESD)

Some semiconductor (solid state) devices can be dam­aged easily by static electricity.
Such components commonly are called Electrostati­cally Sensitive Devices(ESD). Examples of typical ESD
devices are integrated circuits and some field-effect
transistors and semiconductor chip components. The
following techniques should be used to help reduce
the incidence of component damage caused by static
electricity.

(1) Immediately before handling any semiconductor

component or semiconductor-equipped assembly,
drain off any electrostatic charge on your body by
touching a known earth ground. Alternatively,
obtain and wear a commercially available dis­charging wrist strap device, which should be
removed for potential shock reasons prior to apply­ing power to the unit under test.

(2) After removing an electrical assembly equipped

with ESD devices, place the assembly on a conduc­tive surface such as aluminum foil, to prevent elec­trostatic charge buildup or exposure of the assem­bly.

(3) Use only a grounded-tip soldering iron to solder or

unsolder ESD devices.

(4) Use only an anti-static solder removal devices.

Some solder removal devices not classified as
“anti-static” can generate electrical charges suffi­cient to damage ESD devices.

(5) Do not use freon-propelled chemicals. These can

generate electrical charges sufficient to damage
ESD devices.

(6) Do not remove a replacement ESD device from its

protective package until immediately before your
are ready to install it.(Most replacement ESD
devices are packaged with leads electrically short­ed together by conductive foam, aluminum foil or
comparable conductive materials).

(7) Immediately before removing the protective ma-

terials from the leads of a replacement ESD device,
touch the protective material to the chassis or cir­cuit assembly into which the device will be
installed.

CAUTION : Be sure no power is applied to the ch­assis or circuit, and observe all other safety precau­tions.

(8) Minimize bodily motions when handling unpack-

aged replacement ESD devices. (Otherwise harm­less motion such as the brushing together of your
clothes fabric or the lifting of your foot from a car­peted floor can generate static electricity sufficient
to damage an ESD device).

Precautions

Samsung Electronics 1-5

1-4 Handling the optical pick-up

The laser diode in the optical pick up may suffer elec­trostatic breakdown because of potential static elec­tricity from clothing and your body.

The following method is recommended.
(1) Place a conductive sheet on the work bench (The

black sheet used for wrapping repair parts.)

(2) Place the set on the conductive sheet so that the

chassis is grounded to the sheet.

(3) Place your hands on the conductive sheet(This

gives them the same ground as the sheet.)

(4) Remove the optical pick up block

(5) Perform work on top of the conductive sheet. Be

careful not to let your clothes or any other static
sources to touch the unit.

◆ Be sure to put on a wrist strap grounded to the
sheet.

◆ Be sure to lay a conductive sheet made of copper
etc. Which is grounded to the table.

Fig.1-3

(6) Short the short terminal on the PCB, which is in-

side the Pick-Up ASS’Y, before replacing the Pick­Up. (The short terminal is shorted when the Pick­Up Ass’y is being lifted or moved.)

(7) After replacing the Pick-up, open the short termi-

nal on the PCB.

THE UNIT

WRIST-STRAP
FOR GROUNDING

1M

1M

CONDUCTIVE SHEET

Precautions

1-6 Samsung Electronics

1-5 Pick-up disassembly and reassembly

1-5-1 Disassembly

1) Remove the power cord.

2) Disassemble the Deck-Assy.

3) Make solder land 2 points short on Pick-up.
(See Fig. 1-4)

4) Disassembly the Pick-up.

1-5-2 Assembly

1) Replace the Pick-up.

2) Remove the soldering 2 points on Pick-up.

3) Reassemble the Deck-Assy.

PICK-UP ASS'Y

SOLDER LAND 2 POINTS SHORT

Note : If the assembly and disassembly are not done in correct sequence, the Pick-up may be damaged.

Fig. 1-4

Samsung Electronics 2-1

2. Alignment and Adjustment

2-1 Location of Test Point

Fig. 2-1 Location of Test Point

SIC1

RIC1

RIC1

SIC1

Alignment and Adjustment

2-2 Samsung Electronics

2-2-1 Adjustment Spec. and Test Point

2-2 Skew Adjustment

Test Disc Adjustment Spec. Test Point Adjustment Location

TDV-533 “ENV” Screw A / B

Chapter 14 Flat Waveform (Main PCB - Component Side) Ass’y Deck - Top Side

(See Fig. 2-1) (See Fig. 2-2)

Fig. 2-2 Ass’y Deck (Top Side)

◆ Test Disc ; Service not Available

<Table 2-1>

Alignment and Adjustment

Samsung Electronics 2-3

2-2-2 SKEW Adjustment Method

Needed to minimize the variations in Skew of the Pickup unit and to provide optimum match with the recorded
signal on the Disc.

1) Connect an Oscilloscope to the “ENV” Test Point (See Fig. 2-1).

2) Connect Power, Open the Tray and Play the TDV-533 Disc, Chapter 14.

◆ Set the Oscilloscope Range as follows :
(Voltage ; 50mV/Div., Frequency ; 10m Sec.)

3) Adjust the Screws “A” and “B” (See Fig. 2-2) using a Hex screwdriver until you obtain a Flat Waveform and
the picture is stable.
Then, go to Chapter 1 and make sure the Waveform is Flat here as well.
If not, you have to go back to Chapter 14 and adjust again.
If you cannot obtain a Flat waveform, then the unit is defective.

Note : The Deck must be in a horizontal position. Use both “A” and “B” screws to adjust.

    



     

Typical Waveform before Adjustment Waveform after Correct Adjustment

Fig. 2-3 Envelope Waveform