Samsung C27A650X User Manual

Download

User Manual

SyncMaster

C24A650X

C27A650X C24A650U C27A650U

The color and the appearance may differ depending on

the product, and the specifications are subject to

change without prior notice to improve the performance.

BN46-00083A-02

Copyright

The contents of this manual are subject to change without notice to improve quality.

Samsung Electronics owns the copyright for this manual.

Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is

prohibited.

The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics.

Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.

Before Using the Product

VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.

z An administration fee may be charged if either

 (a) an engineer is called out at your request and there is no defect in the product

(i.e. where you have failed to read this user manual).

 (b) you bring the unit to a repair centre and there is no defect in the product

(i.e. where you have failed to read this user manual).

z The amount of such administration charge will be advised to you before any work or home visit is

carried out.

Icons used in this manual

The following images are for reference only. Real-life situations may differ from what is shown in the images.

Symbols for safety precautions

Warning

Caution

A serious or fatal injury may result if instructions are not followed.

Personal injury or damage to properties may result if instructions are not followed.

Before Using the Product

Activities marked by this symbol are prohibited.

Instructions marked by this symbol must be followed.

Before Using the Product

Cleaning

Before Using the Product

Cleaning

Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.

Take the following steps when cleaning.

1. Power off the monitor and computer.

2. Disconnect the power cord from the monitor.

Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result.

3. Wipe the monitor with a clean, soft and dry cloth.

z Do not apply a cleaning agent that contains alcohol,

solvent, or surfactant to the monitor.

z Do not spray water or detergent directly on the product.

4. Wet a soft and dry cloth in water and wring thoroughly to clean the exterior of the monitor.

5. Connect the power cord to the product after cleaning the product.

6. Power on the monitor and computer.

Before Using the Product

10 cm

10 cm 10 cm

10 cm

Securing the Installation Space

z Ensure some space around the product for ventilation. A rise in the internal temperature may cause

a fire and damage the product. Be sure to allow the amount of space as shown below or greater when installing the product.

The exterior may differ depending on the product.

Precautions for storage

High-glossy models can develop white stains on the surface if an ultrasonic wave humidifier is used

nearby.

Be sure to contact Samsung Customer Service Center (107page) if the inside of the monitor needs cleaning. (service fee will be charged).

Safety Precautions

Electricity and Safety

The following images are for reference only. Real-life situations may differ from what is shown in the images.

Before Using the Product

Warning

Do not use a damaged power cord or plug, or a loose power socket.

z An electric shock or fire may result.

Do not plug many products into the same power socket.

z Otherwise, the socket may overheat and cause a fire.

Do not touch the power plug with wet hands.

z Otherwise, an electric shock may result.

Insert the power plug all the way in so it is not loose.

z An unstable connection may cause a fire.

Connect the power plug to a grounded power socket (type 1 insulated devices only).

z An electric shock or injury may result.

Do not bend or pull the power cord with force. Do not weigh the power cord down with a heavy object.

z A damaged power cord may cause an electric shock or fire.

Do not place the power cord or product near heat sources.

z An electric shock or fire may result.

Remove foreign substances such as dust around the plug pins and power socket with a dry cloth.

z Otherwise, a fire may result.

Before Using the Product

Caution

Do not unplug the power cord when the product is in use.

z The product may become damaged by an electric shock.

Do not use the power cord for products other than authorized products supplied by Samsung.

z An electric shock or fire may result.

Keep the power socket where the power cord is connected unobstructed.

z If any problem occurs in the product, unplug the power cable to completely

cut the power to the product.

Installation

Warning

Power to the product cannot be completely cut off with the power button.

Hold the plug when disconnecting the power cord from the power socket.

z An electric shock or fire may result.

Do not place candles, insect repellants or cigarettes on top of the product. Do not install the product near heat sources.

z Otherwise, a fire may result.

Avoid installing the product in a narrow space with bad ventilation, such as a bookshelf or wall closet.

z Otherwise, a fire may result due to an increased internal temperature.

Keep the plastic packaging bag for the product in a place that cannot be reached by children.

z Children may suffocate.

Before Using the Product

Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.).

z The product may fall and break or cause a personal injury.

z Using the product in an area with excess vibration may damage the product

or cause a fire.

Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke.

z An electric shock or fire may result.

Do not expose the product to direct sunlight, heat, or a hot object such as a stove.

z Otherwise, the product lifespan may be reduced, or a fire may result.

Caution

Do not install the product within the reach of young children.

z The product may fall and injure children.

Take care not to drop the product when moving it.

z Otherwise, product failure or personal injury may result.

Do not set down the product on its front.

z The screen may become damaged.

When installing the product on a cabinet or shelf, make sure that the bottom edge of the front of the product is not protruding.

z The product may fall and break or cause a personal injury.

z Install the product only on cabinets or shelves of the right size.

Before Using the Product

SAMSUNG

Put down the product carefully.

z The product may fall and break or cause a personal injury.

Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance.

z Be sure to consult Samsung Customer Service Center (107page) before

installation if you want to install the product at such a place.

Operation

Warning

High voltage runs through the product. Do not attempt to disassemble, repair, or modify the product on your own.

z An electric shock or fire may result.

z Contact Samsung Customer Service Center (107page) for repair.

Before you move the product, be sure to turn off the power switch and remove all the cables connected to the product, including the power cord and the antenna cable.

z Otherwise, the power cord may be damaged and a fire or electric shock may

result.

If the product generates a strange noise, a burning smell, or smoke, remove the power cord immediately and contact Samsung Customer Service Center (107page).

z An electric shock or fire may result.

Do not let children hang from the product or climb on top of it.

z The product may fall, and your child may become injured or seriously

harmed.

If the product falls or the exterior is damaged, power off the product, remove the power cord, and contact Samsung Customer Service Center (107page).

z Otherwise, an electric shock or fire may result.

Before Using the Product

GAS

Do not put a heavy object, toy, or sweets on top of the product.

z The product or heavy objects may fall as children try to reach for the toy or

sweets resulting in a serious injury.

During a lightning or thunderstorm, remove the power cord and do not touch the antenna cable.

z An electric shock or fire may result.

Do not drop objects on the product or apply impact.

z An electric shock or fire may result.

Do not move the product by pulling the power cord or any cable.

z Otherwise, the power cable may be damaged and product failure, an electric

shock or fire may result.

If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.

z Sparks can cause an explosion or fire.

z During a lightning or thunderstorm, do not touch the power cord or antenna

cable.

Do not lift or move the product by the power cord or any cable.

z Otherwise, the power cable may be damaged and product failure, an electric

shock or fire may result.

Do not use or keep combustible spray or an inflammable substance near the product.

z An explosion or fire may result.

Ensure the vents are not blocked by tablecloths or curtains.

z Otherwise, a fire may result from an increased internal temperature.

Before Using the Product

100

-_-

Do not insert a metallic object (a chopstick, coin, hair pin, etc.) or inflammable object (paper, match, etc.) into the vent or ports of the product.

z If water or any foreign substance enters the product, be sure to power off the

product, remove the power cord, and contact Samsung Customer Service Center (107page).

z Product failure, an electric shock or fire may result.

Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.

z If water or any foreign substance enters the product, be sure to power off the

product, remove the power cord, and contact Samsung Customer Service Center (107page).

z Product failure, an electric shock or fire may result.

Caution

Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.

z If you are not going to use the product for an extended period of time,

activate power-saving mode or a moving-picture screen saver.

Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).

z Otherwise, a fire may result from accumulated dust, overheating, an electric

shock, or electric leakage.

Use the product at the recommended resolution and frequency.

z Your eyesight may deteriorate.

Do not put DC power adapters together.

z Otherwise, a fire may result.

Remove the plastic bag from the DC power adapter before you use it.

z Otherwise, a fire may result.

Before Using the Product

Do not let water enter the DC power device or get the device wet.

z An electric shock or fire may result.

z Avoid using the product outdoors where it can be exposed to rain or snow.

z Be careful not to get the DC power adapter wet when you wash the floor.

Do not put the DC power adapter near to any heating apparatus.

z Otherwise, a fire may result.

Keep the DC power adapter in a well-ventilated area.

Looking at the screen too close for an extended period of time can deteriorate your eyesight.

Do not hold the monitor upside-down or move it by holding the stand.

z The product may fall and break or cause a personal injury.

Do not use humidifiers or stoves around the product.

z An electric shock or fire may result.

Rest your eyes for more than 5 minutes for every 1 hour of product use.

z Eye fatigue will be relieved.

Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.

Store the small accessories used with the product out of reach of children.

Before Using the Product

Exercise caution when adjusting the product angle or stand height.

z Otherwise, children's fingers or hands may become stuck and injured.

z Tilting the product excessively may cause it to fall and result in personal

injury.

Do not place heavy objects on the product.

z Product failure or personal injure may result.

Correct posture to use the product

Use the product in the correct posture as follows:

z Straighten your back.

z Allow a distance of 45 to 50cm between your eye and the screen, and look slightly

downward at the screen.

Keep your eyes directly in front of the screen.

z Adjust the angle so light does not reflect on the screen.

z Keep your forearms perpendicular to your upper arms and level with the back of

your hands.

z Keep your elbows at about a right angle.

z Adjust the height of the product so you can keep your knees bent at 90 degrees or

more, your heels attached to the floor, and your arms lower than your heart.

Before Using the Product

BEFORE USING THE

PRODUCT

PREPARATIONS 19 Checking the Contents

2 Copyright

2 Icons used in this manual 2 Symbols for safety precautions

4 Cleaning

4 Cleaning 5 Securing the Installation Space 5 Precautions for storage

5 Safety Precautions

5 Electricity and Safety 7 Installation 9Operation

13 Correct posture to use the product

19 Removing the Packaging 20 Checking the Components

USING "CENTRAL

STATION"

22 Parts

22 Frontal Buttons 24 Reverse Side

26 Installation

26 Attaching the Stand 27 Left Side View 27 Rotating the Monitor 28 Attaching and detaching the wireless-

connection dongle (Rx) 29 Installing a Wall-mount Kit or Desktop Stand 30 Anti-theft Lock

31 "MagicRotation Auto"

32 About "Central Station"

32 Software Installation for Using "Central

Station"

32 Installing "Samsung Central Station Setup"

Table Of Contents

34 Connecting the Product to a PC to Use

"Central Station"

34 Connecting to a PC via Wireless USB 38 Connecting to a PC via the USB Cable

39 Utilizing "Central Station"

39 Using the Product as a USB HUB 41 Connecting to a LAN

42 Configuring the Central Station Monitor

42 Dynamic IP 43 Static IP

CONNECTING AND USING

A SOURCE DEVICE

SCREEN SETUP 57 MAGIC

46 Notice before your use of Wireless USB

or USB Mode

47 Before Connecting

47 Pre-connection Checkpoints

48 Connecting and Using a PC

48 Connecting to a PC 50 Driver Installation 51 Setting Optimum Resolution 52 Changing the Resolution Using a PC

55 Connecting Headphones

56 Connecting the Power

57 SAMSUNG MAGIC Bright 59 SAMSUNG MAGIC Color

60 Brightness

60 Configuring Brightness

61 Contrast

61 Configuring Contrast

62 Sharpness

62 Configuring Sharpness

Table Of Contents

63 Coarse

63 Adjusting Coarse

64 Fine

64 Adjusting Fine

65 Response Time

65 Configuring Response Time

CONFIGURING TINT 66 Red

66 Configuring Red

67 Green

RESIZING OR

RELOCATING THE

SCREEN

67 Configuring Green

68 Blue

68 Configuring Blue

69 Color Tone

69 Configuring the Color Tone Settings

70 Gamma

70 Configuring Gamma

71 Image Size

71 Changing the Picture Size

72 H-Position & V-Position

72 Configuring H-Position & V-Position

73 Menu H-Position & Menu V-Position

73 Configuring Menu H-Position & Menu V-

Position

Table Of Contents

SETUP AND RESET

74 HUB

74 Auto Wireless Detection 75 Wireless Connection 76 USB Connection 77 Analog 78 HDMI 79 USB Super Charging 79 Wireless ID

80 ECO

80 Eco Motion Sensor 82 Eco Light Sensor 85 Eco Saving 86 Eco Icon Display

88 Menu Transparency

88 Changing Menu Transparency

89 Language

89 Changing the Language

90 PC/AV Mode

90 Configuring PC/AV Mode

91 Auto Source

91 Configuring Auto Source

92 Display Time

92 Configuring Display Time

93 Key Repeat Time

93 Configuring Key Repeat Time

94 Customized Key

94 Configuring Customized Key

95 Off Timer On/Off

95 Configuring Off Timer On/Off

96 Off Timer Setting

96 Configuring Off Timer Setting

Table Of Contents

97 Reset

97 Initializing Settings (Reset)

INFORMATION MENU AND

OTHERS

TROUBLESHOOTING

GUIDE

SPECIFICATIONS 103 General

98 INFORMATION

98 Displaying INFORMATION

98 Configuring Brightness in the Startup

Screen

99 Requirements Before Contacting

Samsung Customer Service Center

99 Testing the Product 99 Checking the Resolution and Frequency

100 Check the followings.

102 Q & A

105 PowerSaver

106 Standard Signal Mode Table

APPENDIX 107 Contact SAMSUNG WORLDWIDE

111 Correct Disposal of This Product (Waste

Electrical & Electronic Equipment)

112 Terminology

INDEX

Table Of Contents

Preparations

1.1 Checking the Contents

1.1.1 Removing the Packaging

1 Open the packaging box. Be careful not to damage the product when you open the packaging with

a sharp instrument.

2 Remove the Styrofoam from the product.

3 Check the components and remove the Styrofoam and plastic bag.

z The appearance of actual components may differ from the image shown.

z This image is for reference only.

4 Store the box in a dry area so that it can be used when moving the product in the future.

1 Preparations

Preparations

1.1.2 Checking the Components

z Contact the dealer from whom you purchased the product if any item is missing.

z The appearance of the components and items sold separately may differ from the image shown.

Components

Quick setup guide Warranty card

(Not available in all locations)

Wireless Connection

Dongle(Tx)

(Sold separately for C24A650U

and C27A650U models)

Power cable DC power adapter USB 3.0 cable

Wireless Connection

(Sold separately for C24A650U

and C27A650U models)

User manual

Stand base

Dongle(Rx)

D-SUB cable HDMI cable (optionally) USB gender changer

Components may differ in different locations.

1 Preparations

Preparations

USB gender changer

When the wireless-connection dongle cannot connect to your notebook PC, connect it using the USB

gender changer.

Items sold separately

The following items can be purchased at your nearest retailer.

LAN cable HDMI-DVI cable

1 Preparations

Preparations

HUB

1.2 Parts

1.2.1 Frontal Buttons

The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Icons Description

z Open or close the onscreen display (OSD) menu, or return to the last

menu.

z OSD control lock: Maintain the current settings, or lock the OSD

control to prevent unintended changes to settings.

To lock the OSD control, press the MENU button [ ] for five

seconds.

To unlock the locked OSD control, press the MENU button [ ]

for more than five seconds.

If the OSD control is locked,

z Brightness and Contrast can be adjusted, and INFORMATION

can be viewed.

z The function that was configured as Customized Key before

locking the OSD control can be used by pressing the [ ] button.

1 Preparations

HUB

AUTO

Preparations

Icons Description

Configure Customized Key and press [ ]. The following options will be enabled.

HUB - ECO - MAGIC - Image Size

To configure Customized Key, go to SETUP&RESET

Customized Key and select the mode you want.

→

Move to the upper or lower menu or adjust the value for an option on the OSD menu.

Adjust the screen brightness.

Volume (VOL) can be adjusted if a cable is connected to the [HDMI IN]

port.

Confirm a menu selection.

Pressing the [ ] button when the OSD menu is not displayed will change the input source (Wireless USB/USB/Analog/HDMI). If you power on the product or change the input source by pressing the [ ] button, a message that shows the changed input source will appear at the top left corner of the screen.

Press the [ ] button to automatically adjust the screen settings.

AUTO

z Available only in Analog mode.

(Power Indicator)

z Changing the resolution in Display Properties will activate the

Auto Adjustment function.

Turn the screen on or off.

The power indicator will be lit when the product is operating normally.

z Refer to "10.2 PowerSaver" for details about the power-saving

function.

z To reduce power consumption, it is best to remove the power

cable when you will not be using the product for an extended period of time.

z The power LED will turn red if a wireless communication

connection is established.

1 Preparations

DC 14V HDMI IN RGB IN

WIRELESS LAN ADAPTER

LAN

Preparations

1.2.2 Reverse Side

The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Port Description

Connects to the DC power adapter.

Connects to a source device using an HDMI cable.

Connects to a PC using the D-SUB cable.

Connects to a network using the LAN cable.

Connects to an audio output device such as headphones.

Connects to a source device via a USB cable. Compatible with a USB cable version 2.0 or lower.

Connects to a source device via a USB cable. Compatible with a USB cable version 3.0 or lower.

1 Preparations

Preparations

Port Description

Connects to a PC via a USB cable.

This port can only connect to a PC.

Connect to the wireless-connection dongle (Rx).

1 Preparations

Preparations

1.3 Installation

1.3.1 Attaching the Stand

Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion.

Tightly fasten the screw to the bottom of the base.

Insert the stand base into the stand in the direction of the arrow.

After installing the stand, place the product upright.

Do not remove the fixing pin until you are finished attaching the stand.

You can remove the fixing pin and adjust the stand now.

- Caution

Do not hold the product upside down only by the stand.

The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

1 Preparations

Preparations

1.3.2 Left Side View

The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

z To adjust the height, remove the fixing pin.

z The monitor tilt and height can be adjusted.

z Hold the top center of the product and adjust the height carefully.

1.3.3 Rotating the Monitor

You can rotate your monitor as shown below.

z Be sure to fully extend the stand before rotating the monitor.

z If you rotate the monitor without fully extending the stand, the corner of the monitor may hit the

floor and get damaged.

z Do not rotate the monitor counterclockwise. The monitor may get damaged.

1 Preparations

Preparations

1.3.4 Attaching and detaching the wireless-connection dongle (Rx)

Attaching the wireless-connection dongle (Rx)

Detaching the wireless-connection dongle (Rx)

1 Preparations

Preparations

1.3.5 Installing a Wall-mount Kit or Desktop Stand

Before Installation

Power the product off and remove the power cable from the power socket.

Place a protective cloth or cushion on a flat surface. Next, place the product with the face down on top of the cloth or cushion.

Installing a Wall-mount Kit or Desktop Stand

Unfasten the screw from the back of the product.

Lift and detach the stand.

Attach the wall-mount kit or desktop stand here

Bracket (sold separately)

Align the grooves and tightly fasten the screws on the bracket on the product with the corresponding

parts on the wall-mount kit or desktop stand you want to attach.

1 Preparations

Preparations

Notes

z Using a screw longer than the standard length can damage the internal components of the

product.

z The length of screws required for a wall mount that does not comply with the VESA standards may

vary depending on the specifications.

z Do not use screws that do not comply with the VESA standards. Do not attach the wall-mount kit

or desktop stand using excessive force. The product may get damaged or fall and cause personal injury. Samsung shall not be held liable for any damage or injury caused by using improper screws or attaching the wall-mount kit or desktop stand using excessive force.

z Samsung shall not be held liable for any product damage or personal injury caused by using a wall-

mount kit other than the one specified or from an attempt to install the wall-mount kit on your own.

z To mount the product on a wall, ensure you purchase a wall-mount kit that can be installed 10cm

or farther away from the wall.

z Be sure to use a wall-mount kit that complies with the standards.

1.3.6 Anti-theft Lock

An anti-theft lock allows you to use the product securely even in public places. The locking device shape

and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft

locking device for details. The lock device is sold separately.

To lock an anti-theft locking device:

1 Fix the cable of your anti-theft locking device to a heavy object

such as a desk.

2 Put one end of the cable through the loop on the other end. 3 Insert the locking device into the anti-theft lock slot at the back of

the product.

4 Lock the locking device.

z An anti-theft locking device can be purchased separately.

z Refer to the user guide provided with your anti-theft locking device for details.

z Anti-theft locking devices can be purchased at electronics retailers or online.

1 Preparations

Preparations

(QJOLVK)UDQoDLV'HXWVFK0DJ\DU,WDOLDQR3ROVNL3RUWXJXrV ƧǊǈǈǁƿǀ(VSDxRO6YHQVND7UNoHᣣᧄ⺆㩷∝䇁ଞ˲߭

1.4 "MagicRotation Auto"

The "MagicRotation Auto" function detects the rotation of monitors that are fitted with a rotation sensor

and rotates the Windows screen accordingly.

[Software Installation]

1 Insert the user manual CD provided with the product into the CD-ROM drive. 2 Follow the instructions given on the screen to proceed with installation.

After installation, the on-screen display (OSD) menu will be displayed in the language of the operating system.

(This complies with the basic policies of Windows.)

[Caution]

1 Compatible only with Windows 7 (32 bits or 64 bits) 2 Compatible with a graphics card that complies with the DDC/CI and MS API standards

With a graphics card that does not comply with the aforementioned standards, the "MagicRotation

Auto" function may not be available.

3 To maximize the performance of the function, update the graphics card driver to the latest version. 4 Fourteen languages are available as installation languages.

5 If the orientation is set to a mode other than "Landscape" in the screen resolution menu on Windows

7, the "MagicRotation Auto" function may not work properly.

6 The OSD menu will be displayed if the monitor is rotated. When the monitor is rotated, the screen

reconfiguration process may be displayed or screen burn-in may appear, depending on the graphics card. This is performed by the Windows operating system and has nothing to do with the product.

7 If you do not want the screen to rotate automatically when the monitor is rotated, press the Windows

and L keys at the same time to lock the Windows operating system. If the operating system cannot be locked, it is due to the constraints of Windows API and has nothing to do with the product.

8 This function is not available when the input source is Wireless USB or USB.

1 Preparations

Using "Central Station"

You can use the "Central Station" function by connecting the product to a PC through the Wireless USB function or a USB cable. "Central Station" allows the product to function as a HUB so that you can control a connected device from the product without having to connect to a PC.

2.1 About "Central Station"

"Central Station" is a HUB system developed independently by Samsung and allows you to conveniently

control a notebook PC that has a small screen and a limited number of input/output ports available.

Notebook or netbook computers offer portability but may prove inconvenient when used at the office or

at home. Connecting a notebook PC to this product, which has the "Central Station" function, allows you

to view the small notebook PC screen on a larger screen. With the HUB function, you can control multiple

devices at the same time from the notebook PC, even if the notebook PC has a limited number of input/

output ports.

In particular, the high-tech Wireless USB feature allows you to connect a notebook PC to the product

wirelessly and, from the product, enjoy various multimedia contents stored on the notebook PC.

You can also use triple monitors by configuring the display settings.

2.2 Software Installation for Using "Central Station"

Install on your PC the software provided with the product.

To maximize the performance of your Central Station monitor, visit www.samsung.com/sec and upgrade

the driver periodically.

2.2.1 Installing "Samsung Central Station Setup"

This software is needed to use the Central Station function. Software installation may be affected by the

graphics card, motherboard, or network conditions of the PC.

1 Insert the installation CD into the CD-ROM drive. 2 Click the "Samsung Central Station Setup" installation program.

z To connect the product to a PC using a USB cable, click the [ ] program.

z To connect the product to a PC via Wireless USB or a USB cable, click the [ ] program.

If a software installation window does not appear in the main screen, install "Samsung Central Station Setup" using the execution file ("CA650_wired_setup_file") on the CD-ROM.

(For C24A650U and C27A650U models, the wireless-connection [Tx and Rx] dongles are sold

separately.)

If a software installation window does not appear in the main screen, install "Samsung Central Station Setup" using the execution file ("CA650_wireless_setup_file") on the CD-ROM.

2 Using "Central Station"

→ → →

→

Using "Central Station"

3 Follow the instructions given on the screen to proceed with installation.

Select the country where you will use the product when installing the driver initially. Using the product in a country other than the selected country would be contrary to the law. (Applicable only when the [ ] program is installed using the execution file ("CA650_wireless_setup_file").)

4 After installing "Samsung Central Station Setup", customize the audio output port settings as

required.

Control Panel Sound Speakers Configure Speakers

"Samsung Central Station Setup" software consists of "Samsung Wireless Central Station" and "Samsung Wireless Monitor". To delete the software, go to Start Settings Control Panel and double-click Add or Remove Programs on the PC. Select "Samsung Wireless Central Station" and "Samsung Wireless Monitor" from the list and click Change/Remove. (Applicable only when the [ ] program is installed using the execution file ("CA650_wireless_setup_file").)

2 Using "Central Station"

Using "Central Station"

CSM

WIRELESS USB

WIRELESS LAN ADAPTER

2.3 Connecting the Product to a PC to Use "Central Station"

Connect the product to a PC via Wireless USB and the USB cable.

Connecting the product and PC via Wireless USB and the USB cable will allow you to hear audio when

you plug headphones or speakers into [ ] on the product. (Not available when the D-SUB or HDMI-DVI

cable is connected.)

If a PC is connected, the product will automatically switch to the mode of the detected input source. If

several source devices are connected to the product, the input source will automatically change

according to this priority, from left to right: Wireless USB mode > USB mode > Analog mode > HDMI

mode.

When the product connects to a PC for the first time, the optimum resolution (1920 x 1080) will be

selected automatically and the display will be set to extended mode. For subsequent connections of the

product to the PC, customized resolution settings will be applied.

When multiple display output ports on the PC are connected to the Central Station monitor, different signals may output depending on the system specifications of the PC.

2.3.1 Connecting to a PC via Wireless USB

z For C24A650U and C27A650U models, the wireless-connection (Tx and Rx) dongles are sold

separately.

z The power LED will turn red if a wireless communication connection is established.

To use the Wireless USB function, connect the wireless-connection dongle (Rx) provided with the

product to the [WIRELESS LAN ADAPTER] port on the product. Next, connect the wireless-connection

dongle (Tx) to the USB port on the PC. The wireless-connection dongle allows a wireless connection

2 Using "Central Station"

Using "Central Station"

between the product and a PC. The dongle connected to a PC should point at the product to maximize

signal reception.

Wireless communication can be affected by the surrounding environmental conditions. Do not place an object, or obstacle, between the monitor and PC. The object can affect the sensitivity of the signal transmission/reception.

z Ensure the receiver (dongle) on the Central Station monitor is at the same level and facing the

transmitter (dongle) on the PC.

z The sensitivity of the signal reception/transmission can affect the performance of video or game

z To maximize the transmission/reception, attach the transmitter (dongle) to the USB port (on either

z To maximize the wireless communication performance, ensure your PC is within a range of 70cm

z Using the Central Station monitor on a steel table will degrade wireless performance.

z Do not place any object that can obstruct the signal transmission in front of the product. Such

z This product cannot connect to multiple PCs wirelessly at the same time and vice versa.

The table is a potential obstacle and can degrade wireless performance if the receiver (dongle) on the Central Station monitor is not placed at the same level as the transmitter (dongle) on the PC. This issue may occur even if the dongles face each other.

playback (choppy or slowed-down video).

side of the notebook PC) that is closest to the receiver (dongle) on the Central Station monitor.

from the receiver (dongle) on the Central Station monitor. Ensure the PC and monitor are placed on the same table or at the same height. Otherwise, the signal transmission/reception can be degraded.

objects may decrease signal reception.

Connecting to a PC via Wireless USB

1 Install "Samsung Central Station Setup" on the PC, and attach the dongle to the USB port on the

PC.

2 Press [ ] to change the input source for the product to Wireless.

2 Using "Central Station"

Using "Central Station"

3 Double-click the "Wireless Display Manager" icon created on the desktop. The following screen will

appear.

Five levels of signal intensity are available.

All the five signal intensity indicator bars, including the green bar, will be lit when the strongest signal

is received. The weakest signal intensity will turn on the red bar only.

4 Double-click the hub monitor to open the following screen.

The following "Found New Hardware Wizard" screen may appear when the product attempts to connect to a PC via Wireless USB. Proceed with installation following the instructions displayed.

If a connection is established between the product and PC, [ ] will appear over the signal intensity

bars as shown below and the product will display the PC screen. If [ ] does not appear, the

connection is not established between the product and PC.

2 Using "Central Station"

Using "Central Station"

5 Right-click on Connected Monitor to display the context menu as shown below.

z Disconnect: Disconnect Wireless between the product and PC.

z Set as default: Give first priority to the product to connect to the PC once a Wireless signal is

detected. A star will appear beside the monitor icon if the product is set as the default monitor.

z Rename: Customize the name of the connected monitor.

Automatic/manual Wireless USB connection

Set Auto Wireless Detection to On under HUB in the on-screen display menu. A Wireless USB

connection will automatically be established if the product is within 70cm from the PC. The first priority

will be given to a Wireless USB connection even when the product is in power-saving mode or is

connected to another input source (Analog/HDMI/USB). The Connecting to PC… message will be

displayed while connection is attempted.

To establish a Wireless USB connection when Auto Wireless Detection is set to Off, press [ ] to

switch to Wireless USB mode. The Connecting to PC… message will be displayed while connection is

attempted. Deactivating the Wireless USB mode will automatically restore the previous mode.

The program will automatically activate to allow you to use the Wireless USB connection even when the "Wireless Display" window is closed.

2 Using "Central Station"

Using "Central Station"

2.3.2 Connecting to a PC via the USB Cable

Connect the USB cable to [ ] on the back of the product and USB [ ] on the PC.

A USB 2.0 cable can be used to connect the product to a PC. However, the PC should support USB

3.0 for the USB 3.0 function to work fully.

Connecting to a PC using the USB cable

1 Connect a desktop PC to the product using the USB cable. 2 Press [ ] to change the input source for the product to USB mode. 3 The product will display the PC screen if the connection is established.

Automatic/manual USB cable connection

The input source will automatically change to USB mode if a USB cable connects to the product and a

PC. The USB mode will be given top priority even when the product is in power-saving mode or is

connected to another source (Analog/HDMI). If the input source does not switch to USB mode

automatically, press [ ] to switch to USB mode.

z Top priority will be given to Wireless USB mode if the product is connected to Wireless USB and a

USB cable at the same time.

z Disconnecting the USB cable will automatically restore the previous mode.

2 Using "Central Station"

Using "Central Station"

WIRELESS LAN ADAPTER

2.4 Utilizing "Central Station"

Central Station is only available when the product is connected to a PC via Wireless USB or a USB cable.

2.4.1 Using the Product as a USB HUB

Using the product as a hub, connect and use various source devices with the product at the same time.

A PC cannot connect to multiple source devices at the same time as it has a limited number of input/

output ports available. The HUB feature on the product will improve your work efficiency by allowing you

to connect multiple source devices to the USB ports on the product at the same time without connecting

them to a PC.

z The product is compatible with a USB 2.0 cable. However, your PC should support USB 3.0 for

the HUB function to work fully.

z If you experience a communication problem with a PC that provides the USB 3.0 function,

download and install the latest driver version from the PC manufacturer.

Using the Product as a USB HUB

If multiple source devices are connected to the PC, the many cables around the PC may look messy.

Connecting the devices directly to the product will resolve such inconvenience.

z To detect and start a source device faster, connect the device to the blue USB 3.0 port on the

back of the product.

z An external mass-storage HDD requires external power supply. Be sure to connect it to a power

source.

2 Using "Central Station"

WIRELESS LAN ADAPTER

Using "Central Station"

Connect a mobile IT device such as an MP3 player or smart phone to the product when connected to a

PC. This allows you to use the device from the PC or charge the battery on the device.

z To charge the battery of a device, be sure to connect the device to the blue USB 3.0 port on the

back of the product.

z Battery charging is available in power-saving mode, but not available when the product is powered

off.

z Note that the battery will not be charged if the power cable is disconnected from the power socket.

Connect multiple source devices to the product and use the device you want by changing the input

source.

2 Using "Central Station"

LAN

WIRELESS LAN ADAPTER

LAN

Using "Central Station"

2.4.2 Connecting to a LAN

"Central Station" allows you to use the Internet from a PC when you connect a LAN cable to the product

(if the product is connected to the PC), without having to connect the LAN cable directly to the PC.

This is achieved by an internal chip that transmits data received via the LAN cable to the PC as a

converted USB signal.

Connecting to a LAN via Wireless USB

Connecting to a LAN via USB cable

This product cannot connect to multiple source PCs at the same time and vice versa.

2 Using "Central Station"

Using "Central Station"

2.5 Configuring the Central Station Monitor IP

1 After installing the integrated driver for Central Station monitors, go to Control Panel Network

and Internet Network and Sharing Center Change adapter settings.

→ →

→

2 You can see that the following two devices are displayed.

a. The user PC’s network device

b. The Central Station monitor’s network device (USB to Ethernet adapter)

The two devices above refer to your PC’s LAN network device and your Central Station monitor’s

network device.

To use the Internet using the Central Station monitor’s LAN network, configure the network settings as follows according to the type of IP you will be using.

2.5.1 Dynamic IP

The dynamic IP address mode automatically configures the network settings on the PC using data sent

by a server, which allots an IP address. This is possible, owing to the “DHCP (Dynamic Host

Configuration Protocol)” service. The service consists of three steps: an IP address allotment request is

sent to the DHCP server when the PC boots up, the DHCP server that received the request transmits

network information such as the IP address to the PC, and the transmitted network information is

automatically registered to the network settings on the PC. The DHCP service is convenient and useful

especially in an environment where multiple PCs are used. Theoretically, the IP address changes each

time the PC boots up (or an IP allotment request is sent); in many cases, however, the existing IP address

is re-allotted. An Internet router performs two roles: creating a private IP address (NAT service) and

automatically allotting the IP address to each PC (DHCP service) at the same time.

When using your Central Station monitor’s or notebook PC’s LAN network, ensure you insert a LAN cable into only one device. Otherwise, a system crash may occur.

Dynamic IP User

1 To use a dynamic IP address, connect a LAN to your Central Station monitor. 2 Next, go to the network settings menu and activate the Central Station monitor’s network device

(select “Use”).

2 Using "Central Station"

→ → →

→

Using "Central Station"

Go to Control Panel Network and Internet Network and Sharing Center Change adapter settings. Next, right-click on the Central Station monitor’s network device (marked “LAN9512/LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”) and select Use.

3 Using the network properties menu, check that the IP address mode for the Central Station

monitor’s network device is set to Auto.

Select Properties Internet Protocol Version 4 (TCP/IPv4) Properties.

2.5.2 Static IP

To configure the IP address (private or official) on your PC, someone (mostly a server system) must

distribute and allot an IP address to the PC. An official IP address is allotted by your Internet service

provider, and a private IP address is allotted by your Internet router. You can select whether to configure

the IP address on the PC automatically or manually. The static IP address mode is used to manually enter

an IP address. The static IP address mode is suitable if the IP address for the PC should not be changed

(such as for a file sharing server) and generally is not used, except under such special circumstances.

When using your Central Station monitor’s or notebook PC’s LAN network, ensure you insert a LAN cable into only one device. Otherwise, a system crash may occur.

2 Using "Central Station"

→ → →

→

Using "Central Station"

Static IP User

1 Set the LAN network for the notebook PC to Do not use. 2 Go to Control Panel Network and Internet Network and Sharing Center Change

adapter settings. Next, right-click on the notebook PC’s network device and select Do not use.

→ → →

3 Right-click on the Central Station monitor’s network device (marked “LAN9512/LAN9514 USB 2.0

to Ethernet 10/100 Adapter #7”), and select Use.

Be sure to perform this process before configuring the IP.

4 Configure the static IP. Assign the static IP that is allotted to the Central Station monitor’s network

device.

→

2 Using "Central Station"

Using "Central Station"

5 After configuring the IP, click OK. The following message will appear.

6 Click Close.

A static IP must be allotted to only one network device. The following message will appear if the same static IP is allotted to the network devices of both the notebook PC and Central Station monitor. (Ensure the network device that is not in use is set to Do not use.)

Select No in the message window.

To use the notebook PC’s LAN network, set the Central Station monitor’s network to Do not use

and the notebook PC’s network device to Use. Next, configure the IP settings.

2 Using "Central Station"

Using "Central Station"

2.6 Notice before your use of Wireless USB or USB Mode

1 Most games require a high resolution and fast response time. When you play a game, it is

recommended that you use Analog or HDMI mode instead of Wireless USB or USB mode. Note that playing a game or movie is not supported in Wireless USB or USB mode on a Windows XP or VISTA operating system.

2 Recognizing the Wireless USB or USB mode may take awhile if the mode is used for the first time or

the standby mode is deactivated on the PC.

3 To use the USB HUB function when the monitor is in USB mode (when the monitor is connected to

the USB 2.0 port on the PC) or in Wireless USB mode, it is best to connect a USB cable to the black USB 2.0 port on the monitor.

4 If the PC enters Standby mode when the monitor is in Wireless USB mode, the wireless connection

will be disconnected and the USB HUB function will be disabled.

2 Using "Central Station"

Connecting and Using a Source Device

3.1 Before Connecting

3.1.1 Pre-connection Checkpoints

z Before connecting a source device, read the user manual provided with it.

The number and locations of ports on source devices may differ from device to device.

z Do not connect the power cable until all connections are completed.

Connecting the power cable during connection may damage the product.

z Check the types of ports at the back of the product you want to connect.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

RGB IN

HDMI IN

3.2 Connecting and Using a PC

3.2.1 Connecting to a PC

z Select a connection method suitable for your PC.

Connecting parts may differ in different products.

Connection using the D-SUB cable (analogue type)

1 Connect the D-SUB cable to the [RGB IN] port on the back of the product and the RGB port on the

PC.

2 Connect the DC power adapter to the product and a power socket, and turn on the power switch

on the PC.

(For details, refer to "3.4 Connecting the Power". )

3 Press [ ] to change the input source to Analog.

Audio is not available if the PC and product are connected via the D-SUB port.

Connection Using an HDMI-DVI Cable

1 Connect the HDMI-DVI cable to the [HDMI IN] port on the back of the product and the DVI port on

the PC.

2 Connect the DC power adapter to the product and a power socket, and turn on the power switch

on the PC.

(For details, refer to "3.4 Connecting the Power". )

3 Press [ ] to change the input source to HDMI.

3 Connecting and Using a Source Device

HDMI IN

Connecting and Using a Source Device

Audio is not available if the PC and product are connected via the HDMI-DVI port.

Connection Using an HDMI Cable (Digital Type)

1 Connect the HDMI cable to the [HDMI IN] port on the back of the product and the HDMI port on the

PC.

2 Connect the DC power adapter to the product and a power socket, and turn on the power switch

on the PC.

(For details, refer to "3.4 Connecting the Power". )

3 Press [ ] to change the input source to HDMI.

If audio is supported, the Volume (VOL) can be adjusted using the [] buttons on the front of the product.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

3.2.2 Driver Installation

z You can set the optimum resolution and frequency for this product by installing the corresponding

drivers for this product.

z An installation driver is contained on the CD supplied with the product.

z If the file provided is faulty, visit the Samsung homepage (http://www.samsung.com/sec) and

download the file.

1 Insert the user manual CD provided with the product into the CD-ROM drive. 2 Click "Windows Driver". 3 Follow the instructions given on the screen to proceed with installation. 4 Select your product model from the list of models.

5 Go to Display Properties and check that the resolution and refresh rate are appropriate.

Refer to your Windows OS manual for further details.

3 Connecting and Using a Source Device

The optimal resolution for this monitor is as follows:

1920 x 1080 60Hz

Follow the above settings to set the resolution.

English

AUTO

Connecting and Using a Source Device

3.2.3 Setting Optimum Resolution

An information message about setting optimum resolution will appear if you power on the product for the

first time after purchase.

Select a language and change the resolution to the optimum value.

1 Press [ ] to move to the language you want and press the [ ]. 2 To hide the information message, press [ ].

z If the optimum resolution is not selected, the message will appear up to three times for a specified

time even when the product is turned off and on again.

z The optimum resolution (1920 x 1080) can also be selected in Control Panel on your PC.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

3.2.4 Changing the Resolution Using a PC

z Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture

quality.

z The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected.

Changing the Resolution on Windows XP

Go to Control Panel Display Settings and change the resolution.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

Changing the Resolution on Windows Vista

Go to Control Panel Personalization Display Settings and change the resolution.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

Changing the Resolution on Windows 7

Go to Control Panel Display Screen Resolution and change the resolution.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

3.3 Connecting Headphones

z Connect an audio output device such as headphones or speakers to [ ] on the product.

Headphones will function properly if the product is connected to a PC via USB, Wireless USB or HDMI.

3 Connecting and Using a Source Device

Connecting and Using a Source Device

3.4 Connecting the Power

Put the DC power adapter in the groove, with the switch facing upward.

- Push the adapter until you hear a “click.”

Connect the power cable to the DC power adapter. Next, connect the DC power adapter to the product.

Plug in the power cable to the power socket.

- Removing the DC power adapter

To remove the DC power adapter, lift it outwards from the bottom as shown in the image.

When using the adapter without fixing it to the back of the monitor, the adapter jack can easily get disconnected or the cable may break. Be sure to securely fix the adapter in the groove.

3 Connecting and Using a Source Device

Screen Setup

SAMSUNG

MAGIC

SAMSUNG

MAGIC

SAMSUNG

MAGIC

Return EnterAdjust

Custom Standard Game Cinema Dynamic Contrast

MAGIC

SAMSUNG

MAGIC

Bright

SAMSUNG

MAGIC

Color

AUTO

Configure the screen settings such as brightness and color tone.

4.1 MAGIC

This feature provides the viewing angle, brightness, and tint to suit your preferences.

4.1.1 SAMSUNG MAGIC Bright

This menu provides an optimum picture quality suitable for the environment where the product will be

used.

z Sub-options under Bright may vary depending on the settings of "PC/AV Mode." (See

"Chapter 7. SETUP&RESET.")

z This menu is not available when Eco Light Sensor or Eco Saving is set to On.

Configuring Bright

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to MAGIC and press [ ] on the product. 4 Press [ ] to move to Bright and press [ ] on the product. The following screen will

appear.

[In PC mode]

z Custom: Customize the contrast and brightness as required.

z Standard: Obtain a picture quality suitable for editing documents or using Internet.

z Game: Obtain a picture quality suitable for playing games that involve many graphic effects and

dynamic movements.

z Cinema: Obtain the brightness and sharpness of TVs suitable for enjoying video and DVD

content.

4 Screen Setup

Return EnterAdjust

Dynamic Standard Movie Custom

MAGIC

SAMSUNG

MAGIC

Bright

SAMSUNG

MAGIC

Color

AUTO

Screen Setup

z Dynamic Contrast: Obtain balanced brightness through automatic contrast adjustment.

[In AV mode]

z Dynamic: This mode is suitable when the ambient light is bright.

z Standard: This mode is generally suitable for any environment.

z Movie: This mode reduces eye fatigue.

z Custom: Customize the contrast and brightness as required.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

4 Screen Setup

SAMSUNG

MAGIC

SAMSUNG

MAGIC

SAMSUNG

MAGIC

SAMSUNG

MAGIC

Return EnterAdjust

Off Demo Full Intelligent

MAGIC

SAMSUNG

MAGIC

Bright

SAMSUNG

MAGIC

Color

Custom

AUTO

SAMSUNG

MAGIC

SAMSUNG

MAGIC

Screen Setup

4.1.2 SAMSUNG MAGIC Color

Color is a new picture-quality improvement technology developed independently by Samsung,

which delivers vivid natural colors without picture quality degradation.

This menu is not available when Bright is in Cinema or Dynamic Contrast mode.

Configuring Color

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to MAGIC and press [ ] on the product. 4 Press [ ] to move to Color and press [ ] on the product. The following screen will

appear.

z Off: Disable Color.

z Demo: Compare normal screen mode with Color mode.

z Full: Obtain a vivid picture quality for all areas including the flesh colors in the picture.

z Intelligent: Improve the chroma for all areas except the flesh colors in the picture.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

4 Screen Setup

Screen Setup

SAMSUNG

MAGIC



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

AUTO

2200

Faster

4.2 Brightness

Adjust the general brightness of the picture. (Range: 0~100)

A higher value will make the picture appear brighter.

z This menu is not available when Bright is set to Dynamic Contrast mode.

z This menu is not available when Eco Light Sensor or Eco Saving is set to On.

4.2.1 Configuring Brightness

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Brightness and press [ ] on the product. The following screen will

appear.

4 Adjust the Brightness using the [ ] button.

4 Screen Setup

Screen Setup

SAMSUNG

MAGIC

SAMSUNG

MAGIC

Return EnterAdjust



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

AUTO

2200

Faster

4.3 Contrast

Adjust the contrast between the objects and background. (Range: 0~100)

A higher value will increase the contrast to make the object appear clearer.

z This menu is not available when Bright is in Cinema or Dynamic Contrast mode.

z This menu is not available when Color is in Full or Intelligent mode.

4.3.1 Configuring Contrast

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Contrast and press [ ] on the product. The following screen will appear.

4 Adjust the Contrast using the [ ] button.

4 Screen Setup

Screen Setup

SAMSUNG

MAGIC

SAMSUNG

MAGIC

Return EnterAdjust



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

AUTO

2200

Faster

4.4 Sharpness

Make the outline of objects more clear or blurry. (Range: 0~100)

A higher value will make the outline of objects clearer.

z This menu is not available when Bright is in Cinema or Dynamic Contrast mode.

z This menu is not available when Color is in Full or Intelligent mode.

4.4.1 Configuring Sharpness

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Sharpness and press [ ] on the product. The following screen will

appear.

4 Adjust the Sharpness using the [ ] button.

4 Screen Setup

Screen Setup

Return EnterAdjust



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

2200

Faster

AUTO

4.5 Coarse

Adjust the screen frequency.

Only available in Analog mode.

4.5.1 Adjusting Coarse

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Coarse and press [ ] on the product. The following screen will appear.

4 Adjust the Coarse using the [ ] button.

4 Screen Setup

Screen Setup

Return EnterAdjust



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

2200

Faster

AUTO

4.6 Fine

Fine-adjust the screen to obtain a vivid picture.

4.6.1 Adjusting Fine

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Fine and press [ ] on the product. The following screen will appear.

Only available in Analog mode.

4 Adjust the Fine using the [ ] button.

4 Screen Setup

Screen Setup

Return EnterAdjust



PICTURE

MAGIC

Brightness

Contrast

Sharpness

Coarse

Fine

Response Time

2200

Normal Faster Fastest

AUTO

4.7 Response Time

Accelerate the panel response rate to make video appear more vivid and natural.

z It is best to set Response Time to Normal or Faster when you are not viewing a movie.

z The functions available on the monitor may vary depending on the model. Refer to the actual

product.

4.7.1 Configuring Response Time

1 Press [ ] on the product. 2 Press [ ] to move to PICTURE and press [ ] on the product. 3 Press [ ] to move to Response Time and press [ ] on the product. The following screen will

appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

4 Screen Setup

Configuring Tint

SAMSUNG

MAGIC

SAMSUNG

MAGIC



COLOR

Red

Green

Blue

Color Tone

Gamma

Mode1

Normal

AUTO

Adjust the tint of the screen. This menu is not available when Bright is set to Cinema or

Dynamic Contrast mode.

5.1 Red

Adjust the value of the color red in the picture. (Range: 0~100)

A higher value will increase the intensity of the color.

5.1.1 Configuring Red

1 Press [ ] on the product. 2 Press [ ] to move to COLOR and press [ ] on the product. 3 Press [ ] to move to Red and press [ ] on the product. The following screen will appear.

This menu is not available when Color is in Full or Intelligent mode.

4 Adjust the Red using the [ ] button.

5 Configuring Tint

Configuring Tint

SAMSUNG

MAGIC



COLOR

Red

Green

Blue

Color Tone

Gamma

Mode1

Normal

AUTO

5.2 Green

Adjust the value of the color green in the picture. (Range: 0~100)

A higher value will increase the intensity of the color.

This menu is not available when Color is in Full or Intelligent mode.

5.2.1 Configuring Green

1 Press [ ] on the product. 2 Press [ ] to move to COLOR and press [ ] on the product. 3 Press [ ] to move to Green and press [ ] on the product. The following screen will appear.

4 Adjust the Green using the [ ] button.

5 Configuring Tint

Configuring Tint

SAMSUNG

MAGIC



COLOR

Red

Green

Blue

Color Tone

Gamma

0RGH

Normal

AUTO

5.3 Blue

Adjust the value of the color blue in the picture. (Range: 0~100)

A higher value will increase the intensity of the color.

5.3.1 Configuring Blue

1 Press [ ] on the product. 2 Press [ ] to move to COLOR and press [ ] on the product. 3 Press [ ] to move to Blue and press [ ] on the product. The following screen will appear.

This menu is not available when Color is in Full or Intelligent mode.

4 Adjust the Blue using the [ ] button.

5 Configuring Tint

Configuring Tint

SAMSUNG

MAGIC



COLOR

Red

Green

Blue

Color Tone

Gamma

Cool 2 Cool 1 Normal Warm 1 Warm 2 Custom

AUTO

5.4 Color Tone

Adjust the general color tone of the picture.

This menu is not available when Color is in Full or Intelligent mode.

5.4.1 Configuring the Color Tone Settings

1 Press [ ] on the product. 2 Press [ ] to move to COLOR and press [ ] on the product. 3 Press [ ] to move to Color Tone and press [ ] on the product. The following screen will

appear.

z Cool2: Set the color temperature to be cooler than Cool1.

z Cool1: Set the color temperature to be cooler than Normal mode.

z Normal: Display the standard color tone.

z Warm1: Set the color temperature to be warmer than Normal mode.

z Warm2: Set the color temperature to be warmer than Warm1.

z Custom: Customize the color tone.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

5 Configuring Tint

Configuring Tint



COLOR

Red

Green

Blue

Color Tone

Gamma

Mode1 Mode2 Mode3

Normal

AUTO

5.5 Gamma

Adjust the mid-range brightness (Gamma) of the picture.

5.5.1 Configuring Gamma

1 Press [ ] on the product. 2 Press [ ] to move to COLOR and press [ ] on the product. 3 Press [ ] to move to Gamma and press [ ] on the product. The following screen will appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

5 Configuring Tint

Resizing or Relocating the Screen

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

Auto Wide

AUTO

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

4 : 3 16 : 9 Screen Fit

AUTO

6.1 Image Size

Change the picture size.

6.1.1 Changing the Picture Size

1 Press [ ] on the product. 2 Press [ ] to move to SIZE&POSITION and press [ ] on the product. 3 Press [ ] to move to Image Size and press [ ] on the product. The following screen will

appear.

z Auto: Display the picture according to the aspect ratio of the input source.

z Wide: Display the picture in full screen regardless of the aspect ratio of the input source.

z 4:3: Display the picture with an aspect ratio of 4:3. Suitable for videos and standard broadcasts.

z 16:9: Display the picture with an aspect ratio of 16:9. Suitable for DVD content or widescreen

broadcasts.

z Screen Fit: Display the picture with the original aspect ratio without cutting off.

Requirements to activate Image Size

z When connecting to digital output device via DVI/HDMI cable

z When signal resolution is 480p, 576p , 720p, 1080i, 1080p

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

6 Resizing or Relocating the Screen

Resizing or Relocating the Screen

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

Wide

AUTO

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

Wide

AUTO

6.2 H-Position & V-Position

H-Position: Move the screen to the left or right.

V-Position: Move the screen up or down.

z This menu is only available when Image Size is set to Screen Fit.

z Only available in Analog mode.

6.2.1 Configuring H-Position & V-Position

1 Press [ ] on the product. 2 Press [ ] to move to SIZE&POSITION and press [ ] on the product. 3 Press [ ] to move to H-Position or V-Position, and press [ ]. The following screen will

appear.

4 Press [ ] to configure H-Position or V-Position.

6 Resizing or Relocating the Screen

Resizing or Relocating the Screen

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

Wide

AUTO

Return EnterAdjust



SIZE&POSITION

Image Size

H-Position

V-Position

Menu H-Position

Menu V-Position

Wide

AUTO

6.3 Menu H-Position & Menu V-Position

Menu H-Position: Move the menu position to the left or right.

Menu V-Position: Move the menu position up or down.

6.3.1 Configuring Menu H-Position & Menu V-Position

1 Press [ ] on the product. 2 Press [ ] to move to SIZE&POSITION and press [ ] on the product. 3 Press [ ] to move to Menu H-Position or Menu V-Position, and press [ ]. The following

screen will appear.

4 Press [ ] to configure Menu H-Position or Menu V-Position.

6 Resizing or Relocating the Screen

Setup and Reset

HUB

Auto Wireless Detection

Wireless Connection

USB Connection

Analog

HDMI

USB Super Charging

Wireless ID

Off On

Disconnected

Off

- - - - - - - - - - - - - - - - -

Disconnected

AUTO

7.1 HUB

Configure the settings to use the HUB function on the product.

Refer to "Chapter 2. Central Station" for details about how to use the HUB function.

7.1.1 Auto Wireless Detection

If the product is connected to a PC via Wireless USB, it will automatically detect the Wireless USB signal

and change the input source to Wireless USB mode.

Configuring Auto Wireless Detection

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. 4 Press [ ] to move to Auto Wireless Detection and press [ ] on the product. The following

screen will appear.

z Off: Deactivate Auto Wireless Detection

z On: Automatically detect a Wireless USB signal and change the input source to Wireless USB

mode.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

7 Setup and Reset



+8%

$XWR:LUHOHVV'HWHFWLRQ

:LUHOHVV&RQQHFWLRQ

86%&RQQHFWLRQ

$QDORJ

+'0,

86%6XSHU&KDUJLQJ

:LUHOHVV,'

2II

'LVFRQQHFWHG

2II

'LVFRQQHFWHG

&RQQHFWHG



AUTO

Setup and Reset

7.1.2 Wireless Connection

You can view the status of the Wireless USB connection between the product and a PC.

Selecting the Wireless Connection option. The input source will change to Wireless USB mode.

z The connection status will be shown even when the input source is not Wireless USB mode.

z Selecting Wireless Connection when a Wireless USB connection is established will automatically

change the input source to Wireless USB mode.

Activating Wireless Connection

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. A message will appear indicating

that a Wireless USB connection is established or disconnected.

4 If a Wireless USB connection is established, press [ ] to move to Wireless Connection and press

[ ]. The input source will automatically switch to Wireless USB mode.

7 Setup and Reset



+8%

$XWR:LUHOHVV'HWHFWLRQ

:LUHOHVV&RQQHFWLRQ

86%&RQQHFWLRQ

$QDORJ

+'0,

86%6XSHU&KDUJLQJ

:LUHOHVV,'

2II

&RQQHFWHG

'LVFRQQHFWHG

2II

'LVFRQQHFWHG



AUTO

Setup and Reset

7.1.3 USB Connection

You can view the USB cable connection status between the product and a PC.

z The connection status will be shown even when the input source is not USB mode.

z Selecting USB Connection when a USB cable is connected will automatically change the input

source to USB mode.

Configuring USB Connection

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. A message will appear indicating

that a USB cable is connected or disconnected.

4 If a USB cable is connected, press [ ] to move to USB Connection and press [ ]. The input

source will automatically switch to USB mode.

7 Setup and Reset

ࢇࢷ֩Ѝ ۴ࢇѰ



HUB

Auto Wireless Detection

Wireless Connection

USB Connection

Analog

HDMI

USB Super Charging

Wireless ID

Off

Disconnected

Connected

Off

Disconnected

- - - - - - - - - - - - - - - - -

ࢇࢷ֩Ѝ ࣏ࢽ

۴

AUTO

Setup and Reset

7.1.4 Analog

You can view the Analog cable connection status between the product and a PC.

z The connection status will be shown even when the input source is not Analog mode.

z Selecting the Analog option when an analog cable is connected will automatically change the input

source to Analog mode.

Configuring Analog

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. A message will appear indicating

that an analog cable is connected or disconnected.

4 If an analog cable is connected, press [ ] to move to Analog and press [ ]. The input source

will automatically switch to Analog mode.

7 Setup and Reset

ࢇࢷ֩Ѝ ۴ࢇѰ

HUB

Auto Wireless Detection

Wireless Connection

USB Connection

Analog

HDMI

USB Super Charging

Wireless ID

Off

Disconnected

Off

Connected

Disconnected

- - - - - - - - - - - - - - - - -

ࢇࢷ֩Ѝ ࣏ࢽ

۴

AUTO

Setup and Reset

7.1.5 HDMI

You can view the HDMI connection status between the product and an AV device.

z The connection status will be shown even when the input source is not HDMI mode.

z Selecting the HDMI option when an HDMI cable is connected will automatically change the input

source to HDMI mode.

Configuring HDMI

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. A message will appear indicating

that an HDMI cable is connected or disconnected.

4 If an HDMI cable is connected, press [ ] to move to HDMI and press [ ]. The input source

will automatically switch to HDMI mode.

7 Setup and Reset

ࢇࢷ ֩Ѝ ۴ࢇѰ

HUB

Auto Wireless Detection

Wireless Connection

USB Connection

Analog

HDMI

USB Super Charging

Wireless ID

2II

'LVFRQQHFWHG

2II

1SRUW 2SRUWV

AUTO

Setup and Reset

7.1.6 USB Super Charging

A source device's battery can be charged quickly via USB 3.0 port on the product.

z Data transmission is not available if USB Super Charging is on.

z To enable standard charging or data transmission, set USB Super Charging to off.

z The input source does not need to be changed.

Configuring USB Super Charging

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to HUB and press [ ] on the product. 4 Press [ ] to move to USB Super Charging and press [ ] on the product. The following

screen will appear.

z Off: Deactivate USB Super Charging

z 1 Port: Enable a single USB 3.0 port (marked with a charging icon) for quick battery charging.

Only the USB 3.0 port marked [ ] supports high-speed battery charging

z 2 Ports: Enable two USB 3.0 ports for quick battery charging.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

7.1.7 Wireless ID

Wireless ID is a unique ID assigned to a monitor. The "Samsung Central Station Setup" program reads

the ID and identifies each of nearby monitors. The ID is shown in the "Samsung Central Station Setup"

program and in the lower part of the HUB menu.

7 Setup and Reset

Setup and Reset

Return EnterMove



ECO

Eco Motion Sensor

೛%DFNOLJKW

(FR/LJKW6HQVRU

▶6HQVLWLYLW\

▶%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

ଥࢿ

5 Min

Off

Off 5 Min 10 Min 20 Min 30 Min 1 h

AUTO

7.2 ECO

The Eco Motion Sensor, Eco Light Sensor, and Eco Saving options are displayed on the same menu

page so that you can conveniently configure the power saving settings.

7.2.1 Eco Motion Sensor

The Eco Motion Sensor activates to save power when it does not detect any movement within a

specified area for a specified period of time.

Configuring Eco Motion Sensor

Eco Motion Sensor is not available when the monitor is used in portrait mode.

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Eco Motion Sensor and press [ ]. The following screen will appear.

This option is disabled if the product is connected to a PC that is in power-saving mode.

z Off: Deactivate the Eco Motion Sensor function.

z 5 Min: Automatically turn off the power if the sensor has not detected any movement of an

object or person for 5 minutes within the specified range of detection.

z 10 Min: Automatically turn off the power if the sensor has not detected any movement of an

object or person for 10 minutes within the specified range of detection.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

z 20 Min: Automatically turn off the power if the sensor has not detected any movement of an

object or person for 20 minutes within the specified range of detection.

z 30 Min: Automatically turn off the power if the sensor has not detected any movement of an

object or person for 30 minutes within the specified range of detection.

z 1 h : Automatically turn off the power if the sensor has not detected any movement of an object

or person for 1 hour within the specified range of detection.

7 Setup and Reset

Return EnterMove



ECO

Eco Motion Sensor

▶Backlight

(FR/LJKW6HQVRU

▶6HQVLWLYLW\

▶%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

ଥࢿ

5 Min

Off

Off Dimming

AUTO

Setup and Reset

Configuring Backlight

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Backlight and press [ ] on the product. The following screen will

appear.

z Off: Turn off the screen and activate DPMS mode. If Off is selected, it takes several seconds for

the monitor to detect movement and turn on after it turned off.

z Dimming: Reduce the brightness of the screen (still turned on).

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

z The performance of Eco Motion Sensor is maximized to a specific user distance (1m) and angle (40

degrees).

z The sensor may not detect you if you are motionless.

z If you think that the mode entry message appears too frequently, increase the time setting of the

Eco Motion Sensor or turn the Eco Icon Display Off.

z Avoid using radio equipment such as a walkie-talkie near the product as this may cause a product

malfuction.

7 Setup and Reset

SAMSUNG

MAGIC

5HWXUQ (QWHU0RYH



(&2

Eco Motion Sensor

೛%DFNOLJKW

(FR/LJKW6HQVRU

೛6HQVLWLYLW\

೛%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

0LQ

2II

2II 2Q

AUTO

Setup and Reset

7.2.2 Eco Light Sensor

The Eco Light Sensor feature optimizes the view condition and contributes to power saving by adjusting

the screen brightness depending on the ambient light intensity.

z This menu is not available when Bright is in Dynamic Contrast mode.

z This menu is not available when Eco Saving is set .

Configuring Eco Light Sensor

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Eco Light Sensor and press [ ]. The following screen will appear.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

z Off: Deactivate the Eco Light Sensor function.

z On: Automatically adjust the brightness according to the ambient light intensity.

7 Setup and Reset

5HWXUQ (QWHU0RYH



(&2

Eco Motion Sensor

೛%DFNOLJKW

(FR/LJKW6HQVRU

೛6HQVLWLYLW\

೛%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

0LQ

2II

+LJK 0HGLXP /RZ

AUTO

Setup and Reset

Configuring Sensitivity

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Sensitivity and press [ ] on the product. The following screen will

appear.

z High: High sensitivity that maximizes the varying level of screen brightness depending on the

ambient light intensity.

z Medium: Intermediate sensitivity that sets a varying level of screen brightness between High and

Low depending on the ambient light intensity.

z Low: Low sensitivity that minimizes the varying level of screen brightness depending on the

ambient light intensity.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

7 Setup and Reset

5HWXUQ (QWHU0RYH



(&2

Eco Motion Sensor

೛%DFNOLJKW

(FR/LJKW6HQVRU 

೛6HQVLWLYLW\

೛%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

0LQ

2II

+LJK

2II

%ULJKWHU &XUUHQW 'LPPHU

AUTO

Setup and Reset

Configuring Brightness Level

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Brightness Level and press [ ] on the product. The following screen will

appear.

z Brighter: Increase the current brightness of the screen.

z Current: Maintain the current brightness of the screen.

z Dimmer: Decrease the current brightness of the screen.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

7 Setup and Reset

SAMSUNG

MAGIC

Return EnterMove



ECO

Eco Motion Sensor

▶Backlight

(FR/LJKW6HQVRU

▶6HQVLWLYLW\

▶%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

Off

ଥࢿ

Off

 

AUTO

Setup and Reset

7.2.3 Eco Saving

The Eco Saving function reduces power consumption by controlling the electric current used by the

monitor panel.

z This menu is not available when Bright is in Dynamic Contrast mode.

z This menu is not available when Eco Light Sensor is set.

Configuring Eco Saving

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Eco Saving and press [ ] on the product. The following screen will

appear.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

z 75% : Change the monitor power consumption to 75% of the default level.

z 50% : Change the monitor power consumption to 50% of the default level.

z Off: Deactivate the Eco Saving function.

7 Setup and Reset

5HWXUQ (QWHU0RYH



(&2

Eco Motion Sensor

▶Backlight

(FR/LJKW6HQVRU

▶6HQVLWLYLW\

▶%ULJKWQHVV/HYHO

(FR6DYLQJ

(FR,FRQ'LVSOD\

0LQ

2II

2II 2Q

AUTO

wGv

sec

Eco Motion Sensor Activated

Eco Light Sensor Activated Eco Light Sensor Activated

Setup and Reset

7.2.4 Eco Icon Display

Configuring Eco Icon Display

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to ECO and press [ ] on the product. 4 Press [ ] to move to Eco Icon Display and press [ ]. The following screen will appear.

z Off: Disable the Eco Icon Display function.

z On: Display the operation status of the Eco sensor as a pop-up guide.

5 Press [ ] to move to the option you want and press the [ ]. 6 The selected option will be applied.

Notes

z If the monitor is left idle for the period of time to which the off timer is configured when Eco Motion

Sensor is enabled, Eco Motion Sensor will activate and switch the monitor to power-saving mode.

z A 10-second countdown timer will start along with the above picture before the power-saving mode

activates showing the operation status of the Eco Motion Sensor.

z If the screen brightness is adjusted according to the ambient light intensity when the Eco Light

Sensor is on, a pop-up as shown above will appear showing the adjusting screen brightness.

z If the screen becomes brighter as the ambient light becomes brighter, the brightness slide bar level

will increase with a sun image displayed. If the screen becomes darker, the brightness slide bar level

7 Setup and Reset

You've saved

* tree(s).

Setup and Reset

will decrease with a moon image displayed. The brightness slide bar will be displayed for 3 seconds after the sensor activates.

z A pop-up as shown above will appear when an energy tree completes while Eco Icon Display is On.

If the above picture is displayed, it means the Eco Icon Display option is On. Change this setting to

Off if you do not want to display the pop-up.

z The amount of energy saved by the Eco Motion Sensor, Eco Light Sensor, and Eco Saving functions

will accumulate and the progress can be viewed as a growing energy tree.

z The amount of energy savings accumulated by using the power-saving functions, such as Eco

z A complete energy tree will be displayed when the amount of energy savings accumulates to as

z The progress of a tree growing will be represented as 10 different images (stages). After one full-

The energy tree grows as the energy savings of the monitor accumulate. Accordingly, the tree's growth will also be affected by other functions that involve power consumption such as the brightness control function.

Motion Sensor, Eco Light Sensor and Eco Saving, will be calculated and represented as an amount

of carbon dioxide.

much as the amount of carbon dioxide a tree absorbs in a year. This shows that your energy saving is as effective as planting a tree so that you can easily understand the accumulation of energy savings over time and its effect by viewing the progress of a tree growing.

grown tree is complete, the initial image will be restored and the number of trees will continue to accumulate. The number for energy trees will be rounded to one decimal place.

7 Setup and Reset

Setup and Reset

Return EnterAdjust



SETUP&RESET

HUB

ECO

Menu Transparency

Language

PC/AV Mode

Auto Source

Display Time

▶

Off

Manual

20 sec

Off On

AUTO

7.3 Menu Transparency

Set the transparency for the menu windows:

7.3.1 Changing Menu Transparency

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Menu Transparency and press [ ] on the product. The following screen

will appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return EnterMove



SETUP&RESET

ଞ˲߭

HUB

ECO

Menu Transparency

Language

PC/AV Mode

Auto Source

Display Time

'HXWVFK (QJOLVK (VSDxRO )UDQoDLV ,WDOLDQR 0DJ\DU 3ROVNL 3RUWXJXrV ƧǊǈǈǁƿǀ 6YHQVND 7UNoH

ଞ˲߭

∝䇁

ᣣᧄ⺆

AUTO

7.4 Language

Set the menu language.

z A change to the language setting will only be applied to the onscreen menu display.

z It will not be applied to other functions on your PC.

7.4.1 Changing the Language

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Language and press [ ] on the product. The following screen will

appear.

4 Press [ ] to move to the language you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return Enter





SETUP&RESET

▶

English

Manual

20 sec

HUB

ECO

Menu Transparency

Language

PC/AV Mode

Auto Source

Display Time

PC AV

Move

AUTO

7.5 PC/AV Mode

Set PC/AV Mode to AV. The picture size will be enlarged. This option is useful when you view a movie.

PC/AV Mode is only available in HDMI mode.

7.5.1 Configuring PC/AV Mode

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to PC/AV Mode and press [ ] on the product. The following screen will

appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return EnterMove



SETUP&RESET

English

HUB

ECO

Menu Transparency

Language

PC/AV Mode

Auto Source

Display Time

Auto Manual

೛

AUTO

7.6 Auto Source

Activate Auto Source.

7.6.1 Configuring Auto Source

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Auto Source and press [ ] on the product. The following screen will

appear.

z Auto: The input source is automatically recognized.

z Manual: Manually select an input source.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return EnterMove



SETUP&RESET

English

Manual

HUB

ECO

Menu Transparency

Language

PC/AV Mode

Auto Source

Display Time

5 sec 10 sec 20 sec 200 sec

೛

AUTO

7.7 Display Time

Set the on-screen display (OSD) menu to automatically disappear if the menu is not used for a specified

period of time.

Display Time can be used to specify the time after which you want the OSD menu to disappear.

7.7.1 Configuring Display Time

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Display Time and press [ ] on the product. The following screen will

appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return EnterAdjust

Key Repeat Time

Customized Key

Off Timer On/Off

Off Timer Setting

Reset



Acceleration

HUB

SETUP&RESET

AUTO

Acceleration 1 sec 2 sec No Repeat

7.8 Key Repeat Time

Control the response rate of a button when the button is pressed.

7.8.1 Configuring Key Repeat Time

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Key Repeat Time and press [ ] on the product. The following screen

will appear.

z Acceleration, 1 sec, or 2 sec can be selected. If No Repeat is selected, a command responds

only once when a button is pressed.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset



SETUP&RESET

Acceleration

Key Repeat Time

Customized Key

Off Timer On/Off

Off Timer Setting

Reset

Adjust EnterReturn

HUB ECO MAGIC Image Size

AUTO

7.9 Customized Key

You can customize Customized Key as follows.

7.9.1 Configuring Customized Key

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Customized Key and press [ ] on the product. The following screen will

appear.

z HUB - ECO - MAGIC - Image Size

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset

Return EnterAdjust

Key Repeat Time

Customized Key

Off Timer On/Off

Off Timer Setting

Reset



Off On

Acceleration

HUB

SETUP&RESET

AUTO

7.10 Off Timer On/Off

Enable or disable the off timer that automatically powers off the product.

7.10.1 Configuring Off Timer On/Off

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Off Timer On/Off and press [ ] on the product. The following screen will

appear.

z Off: Deactivate the off timer so that the product does not power off automatically.

z On: Activate the off timer so that the product powers off automatically.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

Setup and Reset



SETUP&RESET

Acceleration

HUB

Key Repeat Time

Customized Key

Off Timer On/Off

Off Timer Setting

Reset

10 h

Adjust EnterReturn

AUTO

7.11 Off Timer Setting

The off timer can be set within a range of 1 to 23 hours. The product will automatically power off after the

specified number of hours.

This menu is only available when Off Timer On/Off is set to On.

7.11.1 Configuring Off Timer Setting

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Off Timer Setting and press [ ] on the product. The following screen will

appear.

4 Press [ ] to configure Off Timer Setting.

7 Setup and Reset

Setup and Reset



SETUP&RESET

Acceleration

HUB

Key Repeat Time

Customized Key

Off Timer On/Off

Off Timer Setting

Reset

Adjust EnterReturn

No Yes

AUTO

7.12 Reset

Return all the settings for the product to the default factory settings.

7.12.1 Initializing Settings (Reset)

1 Press [ ] on the product. 2 Press [ ] to move to SETUP&RESET and press [ ] on the product. 3 Press [ ] to move to Reset and press [ ] on the product. The following screen will appear.

4 Press [ ] to move to the option you want and press the [ ]. 5 The selected option will be applied.

7 Setup and Reset

INFORMATION Menu and Others

SETUP&RESET

Analog

67.6kHz 60Hz PP

1920 x 1080

Exit

EnterAdjust

PICTURE

COLOR

SIZE&POSITION

INFORMATION

AUTOEXIT

%ULJKWQHVV

100

EXIT

8.1 INFORMATION

View the current input source, frequency and resolution.

8.1.1 Displaying INFORMATION

1 Press [ ] on the product. 2 Press [ ] to move to INFORMATION. The current input source, frequency and resolution will

appear.

8.2 Configuring Brightness in the Startup Screen

Adjust Brightness using the [ ] button in the startup screen where there is no on screen display menu

available.

1 Press [ ] in the startup screen. The following screen will appear.

2 Adjust the Brightness using the [ ] button.

Volume (VOL) can be adjusted if a cable is connected to the [HDMI IN] port.

8 INFORMATION Menu and Others

Troubleshooting Guide

9.1 Requirements Before Contacting Samsung Customer Service Center

9.1.1 Testing the Product

Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center.

Check if your product is operating normally by using the product test function.

If the screen is turned off and the power indicator blinks even though the product is properly connected

to a PC, perform a self-diagnosis test.

1 Power off both the PC and product. 2 Disconnect the cable from the product. 3 Power on the product. 4 If the Check Signal Cable message appears, the product is working normally.

9.1.2 Checking the Resolution and Frequency

For a mode that exceeds the supported resolution (refer to "10.3 Standard Signal Mode Table"), the

message Not Optimum Mode. will appear for a short time.

If the screen remains blank, check the PC system, video controller and cable.

9 Troubleshooting Guide

Troubleshooting Guide

9.1.3 Check the followings.

Installation issue (PC mode)

The screen keeps switching on and off. Check the cable connection between the product

and PC, and ensure the connection is secure. (Refer to "3.2 Connecting and Using a PC")

Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the monitor and PC.

Screen issue

The power LED is off. The screen will not switch on.

The message Check Signal Cable appears. Check that the cable is properly connected to the

The blank spaces found on the screen have nothing to do with the monitor.

Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the screen size in the HDMI or DVI settings for the graphics card. If the graphics card settings menu does not have an option to adjust the screen size, update the graphics card driver to the latest version.

(Please contact the graphics card or computer manufacturer for further details about how to adjust the screen settings.)

Check that the power cable is connected correctly (Refer to "3.2 Connecting and Using a PC")

product. (Refer to "3.2 Connecting and Using a PC")

Check that the device connected to the product is powered on.

"Not Optimum Mode" is displayed. This message appears if the signal from the

graphics card exceeds the maximum resolution or frequency for the product.

Change the maximum resolution and frequency to suit the product performance, referring to Standard Signal Mode Table (106page).

The images on the screen look distorted. Check the cable connection to the product (Refer

to "3.2 Connecting and Using a PC")

The screen is not clear. The screen is blurry. Adjust Coarse(63page) and Fine(64page).

Remove any accessories (video extension cable, etc) and try again.

Set the resolution and frequency to the recommended level. (Refer to "10.1 General")

9 Troubleshooting Guide

100

Samsung C27A650X User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Copyright

Before Using the Product

Icons used in this manual

Symbols for safety precautions

Cleaning

Cleaning

Securing the Installation Space

Precautions for storage

Safety Precautions

Electricity and Safety

Installation

Operation

Correct posture to use the product

Table Of Contents

Preparations

1.1 Checking the Contents

1.1.1 Removing the Packaging

1.1.2 Checking the Components

1.2 Parts

1.2.1 Frontal Buttons

1.2.2 Reverse Side

1.3 Installation

1.3.1 Attaching the Stand

1.3.2 Left Side View

1.3.3 Rotating the Monitor

1.3.4 Attaching and detaching the wireless-connection dongle (Rx)

1.3.5 Installing a Wall-mount Kit or Desktop Stand

1.3.6 Anti-theft Lock

1.4 "MagicRotation Auto"

Using "Central Station"

2.1 About "Central Station"

2.2 Software Installation for Using "Central Station"

2.2.1 Installing "Samsung Central Station Setup"

2.3 Connecting the Product to a PC to Use "Central Station"

2.3.1 Connecting to a PC via Wireless USB

2.3.2 Connecting to a PC via the USB Cable

2.4 Utilizing "Central Station"

2.4.1 Using the Product as a USB HUB

2.4.2 Connecting to a LAN

2.5 Configuring the Central Station Monitor IP

2.5.1 Dynamic IP

2.5.2 Static IP

2.6 Notice before your use of Wireless USB or USB Mode

Connecting and Using a Source Device

3.1 Before Connecting

3.1.1 Pre-connection Checkpoints

3.2 Connecting and Using a PC

3.2.1 Connecting to a PC

3.2.2 Driver Installation

3.2.3 Setting Optimum Resolution

3.2.4 Changing the Resolution Using a PC

3.3 Connecting Headphones

3.4 Connecting the Power

Screen Setup

4.1 MAGIC

4.1.1 SAMSUNG MAGIC Bright

4.1.2 SAMSUNG MAGIC Color

4.2 Brightness

4.2.1 Configuring Brightness

4.3 Contrast

4.3.1 Configuring Contrast

4.4 Sharpness

4.4.1 Configuring Sharpness

4.5 Coarse

4.5.1 Adjusting Coarse

4.6 Fine

4.6.1 Adjusting Fine

4.7 Response Time

4.7.1 Configuring Response Time

Configuring Tint

5.1 Red

5.1.1 Configuring Red

5.2 Green

5.2.1 Configuring Green

5.3 Blue

5.3.1 Configuring Blue