Safety and Certifications
identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the Telephone Company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The Telephone Company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the Telephone Company will provide advance notice so you can make the necessary modifications to maintain uninterrupted service.
This equipment is not user serviceable. If trouble is experienced with this equipment, for repair or warranty information, please contact Sagemcom at:
Via USA Telephone: +1 (972) 674-4100 |
Or Via Mail: |
|
Sagemcom USA LLC |
|
14651 N. Dallas Parkway |
|
Suite 900 |
|
Dallas, TX 75254 |
If the equipment is causing harm to the telephone network, the Telephone Company may request that you disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. (Contact the state public utility commission, public service commission or corporation commission for information.)
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
This equipment connects to the telephone network that can be vulnerable to electrical surges as a result of lightning strikes and other events. Such events can be very destructive to equipment connected to both the telephone network and to AC power sources. It is strongly recommended that a surge arrestor be used to connect this equipment to AC power in order to reduce the possibility of damage resulting from such events.
FCC Radiation Exposure Statement
This equipment complies with “FCC1.1310 for radiation exposure limits set forth for an uncontrolled environment”. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device produces radio frequency energy in the 2.4 GHz and 5 GHz spectrum. The antenna should be positioned to keep a minimum distance of 30cm (0.98ft) from the radiating element to any nearby person.
Issued by Sagemcom Broadband SAS Sagemcom Broadband
250, route de l'Empereur - 92500 RUEIL MALMAISON - France
© Sagemcom Broadband SAS 2016
All rights reserved. Subject to availability. Rights of modifications reserved. www.sagemcom.com
253670249-A |
11 April 2016 |
4 |
Safety and Certifications
Important Information about the Sagemcom FAST 5566:
Installation and Safe Usage Instructions:
1.Place the VDSL router in a vertical orientation on a flat surface.
2.Connect the manufacturer supplied AC to DC power adapter. The FAST 5566 router requires the use of a 12 VDC, 5000 mA power adapter. Only use a manufacturer supplied and approved power adapter.
Always first plug the mains adapter lead into the FAST 5566, then the mains lead into the mains adapter, and finally the mains lead into the mains socket. If you do not follow this order of connections you may get an electric shock. Make sure that the mains lead is properly inserted into the power supply unit, and that it is correctly pushed into the recess. It is very important to push the mains lead until the recess bottom. If it is incorrectly connected this may cause a risk of fire or electric shock.
3.Connect the FAST 5566 to the AC Mains in accordance with the installation instructions in this booklet, and the markings on the identification label (voltage, current, and frequency of electricity network).
4.Connect the Ethernet cable (provided) to one of the RJ45 ports on the VDSL Router labeled "LAN1", "LAN2", "LAN3", or "LAN4". Then connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as necessary for the other available Ethernet ports.
5.For an Ethernet WAN configuration, connect the RJ45 port labeled “WAN” to the connection provided by your ISP.
6.For an optical fiber network configuration, insert an optical fiber dongle SFP in the port labeled “SFP”, and then connect the dongle SFP to the connection provided by your ISP.
CAUTION: To reduce the risk of laser radiation, always and only use an optical fiber dongle SFP with laser diode of class 1.
7.For a VDSL configuration, connect the provided DSL Cable to the port on the VDSL Router labeled "DSL1". Connect the other end of the DSL Cable to a standard Phone Jack. For a VDSL Bonding configuration, connect a second provided DSL Cable to the port on the VDSL Router labeled "DSL2"
CAUTION: To reduce the risk of fire, always and only use a UL Listed or CSA Certified Telecommunication Line Cord (DSL cable) with a minimum wire gauge of 26AWG (0.4 mm dia. minimum, or 0.129 mm² minimum) or larger (e.g., 24AWG).
8.Only use the rechargeable Lithium Ion battery pack approved and supplied by manufacturer. This battery pack must not be exposed to excessive heat such as the sun, a fire or similar sources. Respect the security instructions on the battery pack identification label.
CAUTION: Risk of explosion if battery pack is replaced by an incorrect type. Dispose of used pack batteries according to the instructions.
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons including the following:
1.Do not use this product near water and avoid contact with moisture. For example, do not use near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that liquids are not spilled on this equipment.
2.This equipment is for indoor use only, do not place or install in an outdoor location.
3.The devices connected to the telephone interfaces must be kept indoor use only.
4.Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire.
5.This equipment should only be operated from the type of power supply (Voltage and Current) indicated on the marking label.
6.Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock.
7.Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in installation such as a cabinet that may impede the flow of air through the ventilation openings.
8.The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other heat producing appliances and equipment.
9.Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by items placed upon or next to it.
10.Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning only.
253670249-A |
11 April 2016 |
1 |
Loading...