SAGEMCOM BROANDS FAST3686V2H Users Manual

Safety and Certifications

Important Information about the Sagemcom “F@ST 3686 V2.2 HP”:

Installation and Safe Usage Instructions:

1. Place the router in a horizontal orientation on a flat surface.

2. Connect the manufacturer supplied AC to DC power adapter. Only use a manufacturer supplied and approved
power adapter and Ethernet cable.

3. Connect the “F@ST 3686 V2.2 HP” to the AC Mains in accordance with the installation instructions in this
booklet, and the

markings on the identification label (voltage, current, and frequency of electricity network).

4. Connect the Ethernet cable (provided) to one of the RJ45 ports on the product labeled "1", "2", "3", or "4". Then
connect the other end of the Ethernet Cable to the Ethernet port of a computer. Repeat as necessary for the
other available Ethernet ports.

When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric
shock, and injury to persons including the following:

1. Do not use this product near water and avoid contact with moisture. For example, does not use near a bathtub,

wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Care should be taken so that
liquids are not spilled on this equipment.

2. This equipment is for indoor use only, do not place or install in an outdoor location.

3. Place your product on a firm, solid surface, no obstacle at a minimum distance of 20cm (0.65ft). If you put it on

something unsteady, it may fall and be damaged. If you place it on a soft surface, such as rug, sofa or cushion,
the vents may be blocked, causing the product to overheat.

4. Never insert objects into the vents of this equipment as this can result in the risk of electrical shock or fire.

5. As the power adapter is the only way to connect to the electrical network, the product must be installed near an

easily accessed power outlet.

6. This equipment should only be operated from the type of power supply (Voltage and Current) indicated on the

marking label.

7. Do not overload wall outlets or extension cords. Doing so can result in the risk of fire or electrical shock.

8. Avoid blocking any vent openings or exhaust exits on this equipment. Do not place equipment in a built-in

installation such as a cabinet that may impede the flow of air through the ventilation openings.

9. The equipment should be situated away from heat sources such as radiators, heat registers, stoves, or other

heat producing appliances and equipment.

10. Care should be taken to ensure that the power cord is routed, so it is not likely to be walked on or pinched by
items placed upon or next to it.

11. Unplug this equipment before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning only.

12. This equipment is not user serviceable and is to be serviced by qualified personnel only. Do not disassemble this
equipment. If service is required, disconnect all power from the equipment and consult qualified service
personnel.

13. To disconnect this equipment from AC power, unplug the power supply from the AC wall socket.

14. Connect only to in house equipment (SELV interface). It is not allowed to connect to public cable distribution or
cable television network.

15. Use the product in the environment specified as below:

- Air temperature between 0°C and +40°C.

- Relative humidity between 20% and 90%.

- Altitude: 5000 meters (16404 ft) maximum.

16. Do not use the telephone to report a gas leak in the vicinity of the leak.

17. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric
shock from lightning.

1

Safety and Certifications

Wall Mount Installation:

This device can be mounted on a wall using the two mounting brackets on the bottom of the device,it is
recommended to use two round or pan head screws (not included)

1. Install two screws horizontally apart on a wall using the measurement shown in Figure 1. The screws should
protrude from the wall in order to fit the device between the head of the screw and the wall. If the screws are
installed in drywall. Use hollow wall anchors to ensure that the unit does not pull away from the wall due to
prolonged strain from the cable and power connectors

2. Remove the device from the product package. Connect the “F@ST 3686 V2.2 HP” to the AC Mains in accordance
with the installation instructions in this booklet, and the
frequency of electricity network).

3. Mount the device on the wall.

Refer to Figures 1 and 2 for more details.

markings on the identification label (voltage, current, and

Figure 1: Distance (horizontal) Between Brackets for Screws

Figure 2: Recommended Screw Size

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired
operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.

2