SAGEMCOM BROANDS FAST3284U User Manual

@SSTT33228844

FF@

User Manual

u

1. Introduction

This F@ST 3284u Cable Gateway is an Embedded Media Terminal Adapter (EMTA) which is CableLabs DOCSIS 3.0 and

PacketCable 1.5 compliant. It provides high-speed Internet access as well as cost-effective, toll-quality telephone voice and

fax/modem services over residential, commercial, and education subscribers on public and private networks via an existing

CATV infrastructure. F@ST 3284u offers high-speed LAN connectivity with 4 Gigabit Ethernet ports and one integrated

Wireless LAN access point compatible with IEEE 802.11a/b/g/n. The Wireless access point is operating on 2.4GHz band.

Package Contents

F@S T3284u Gateway x1

Ethernet Cable (RJ45) x1

Phone Cable (RJ11) x1

Quick Start Guide x1

Power Supply Unit x1

2. Hardware Connection

16

10

8 9

11

1 2 3 4 5 6

7

12 13 14 15

LED Power ON/OFF

1

LED Downstream - indicate receiving RF DS traffic

2

LED Upstream - indicate receiving RF US traffic

3

LED Internet ON/OFF

4

LED WiFi ON/OFF

5

LED Telephone Line 1

6

LED Telephone Line 2

7

WPS button with Blue LED.

8

Wireless ON/OFF button

9

RJ-11 Telephone port lines 1 and 2

10

Ethernet 10/100/1000 BaseT RJ-45 connector

11

Restore To Factory Defaults button

12

RF coaxial F-connector

13

Page 1

Power plug

14

Power switch ON/OFF

15

USB port

16

Wall Mounting

The number of the screw: 2 pcs

Direction for wall mounting: LED panel upward.

Dimension for the screw: 5~7.5 mm

There are 2 slots on the underside of the modem that can be used for wall mounting.

You will need 2 suitable screws which screw diameter would be 5~7.5 mm to wall mount the Cable Gateway.

Note: When wall mounting the unit, ensure that it is within reach of the power outlet.

To wall mount the unit:

1. Ensure that the wall you use is smooth, flat, dry and sturdy and use the 2 screw holes which are 120 mm apart from
each other.

2. Fix the screws into wall, leaving their heads 3 mm (0.12 inch) clear of the wall surface.

3. Remove any connections to the unit and locate it over the screw heads. When in line, gently push the unit on to the
wall and move it downwards to secure.

Page 2

3. Connecting the F@ST3284 Gateway to Your Computer

Installation Procedure for Ethernet Interface

Follow the steps below for proper installation:

1. Make sure your computer meets the system requirements.

2. Connect a coaxial cable to the wall plug

3. Connect a coaxial cable to the CABLE connector on the F@ST3284u and screw it at the bottom manually (do not force).

Note: To speed up the registration process of F@ST3284u, the coaxial cable should be connected to the gateway prior to the power connector.

4. Connect the RJ45 Ethernet cable to the ETHERNET connector on the gateway, connect the other end with the
10/100/1000BaseT Ethernet port on your computer.

5. Plug the RJ11 telephone cord(s) to the TEL 1 or TEL2 connector (s) of the cable modem. (Plug the RJ11 telephone cord(s) to
the PSTN connector on the modem, connect to the PSTN service provider. This step is for EMTA with PSTN model only.)

6. Plug the power supply unit into the POWER connector of the modem.

7. Plug the other end of the power supply unit into a power outlet.

8. Power ON the F@ST3284u by pressing the ON/O FF button on the rear panel of the F@ST3284u.

9. The cable gateway will look for the proper cable modem signal in the Cable Television network and process the initial
registration. The cable gateway is ready for data transfer after the LED “INTERNET” is in solid white. The gateway is ready to
make a phone call after the LED “Tel1 ” or “Tel2” is in solid white.

Note: The RESET button at the rear panel is for maintenance purpose only.

Cable

splitter

The screen of the coaxial cable is intended to be connected to earth in the building installation

Page 3

4. Wireless Connection

Step 1

• Under the gateway, on the
label, note the reference of
SSID and WPA wireless
password.

Step 2

• Click on “Start” then on:

o Network Connection

o Wireless network

connection

5. F@ST3284u Personalization

Step 1

Step 3

Step 4

Step 2

o In this new Window, search

for the SSID value and select
it by double clicking on it.

o The computer asks for a

password. It is the WPA
wireless password.

o Once the password entered

twice, press “Connection”
button. WiFi Configuration is
finished.

• Open an Internet session and type the following address:

http://192.168.1.1

Step 3

• Connect by typing:

Username: admin
Password: admin

• Click on “OK” button

Status

To know the state of your connection of your F@ST3284u

Basic

To perform the basic configuration of your F@ST3284u

Advanced

To perform advanced routing configuration of your F@ST3284u

Firewall

To protect your LAN equipment from malicious attacks

Parental Control

To safely restrict and control the Internet usage to your family

Wireless

To configure the WiFi network of your F@ST3284u

Page 4

MTA

To check the telephony status of your F@ST3284u