SAGEMCOM BROANDS FAST2704N User Manual

Quick Installation Guide

F@ST 2704N

F@ST 2704N

Sagemcom thanks you for choosing the range of F@ST 2704N routers while hoping that
it will provide you with full satisfaction.
F@ST 2704N products adapt the ADSL function respectively on POTS (ITU G.992.1/3/5

- Appendix A) and on ISDN (ITU G.992.1/3/5 - Appendix B).
F@ST 2704N equipment include four ethernet interfaces (LAN1 to LAN4), one ADSL
interface and one USB port (depending model).

CE marking:

The CE marking certifies that the product complies with the essential requirements of the
Directive
1999/5/EC concerning radio equipment and telecommunication equipment, and of
Directives 2006/95/EC concerning safety and 2004/108/EC concerning electromagnetic
compatibility , defined by the European Parliament and Council to reduce electromagnetic
interferences and protect the health and safety of users.
The product named F@ST 2704N can be operated in the European Union without
restrictions indoor but cannot be operated in France in the whole of the band until further
notice.
The EC declaration of conformity can be viewed in the support section of the Sagemcom
site www.sagemcom.com, or it can be obtained from the following address:

Sagemcom Broadband SAS

250, route de l'Empereur

92848 Rueil-Malmaison Cedex - FRANCE

Copyright © Sagemcom Broadband SAS
All rights reserved.
Sagemcom is a registered trademark.

Windows® is a registered trademark of Microsoft Corporation.

2

F@ST 2704N

5

4

3

2

1

7

6

Contents of the pack

Before you carry out the installation, make sure that the pack contains the following
elements:

Item Description

1 F@ST 2704N router
2 Mains adapter

ADSL line cable used to connect your router to your

3

telephone line
Ethernet cable used to connect your router to the

4

Ethernet port of your computer

5 Quick Installation Guide

Filter/Splitter used to connect one phone set and your

6

router to your telephone line*
Microfilter used to connect another phone set to your

7

telephone line*

* Option depending on pack content requested

3

F@ST 2704N

Safety instructions

Power supply source

• Do not cover the router’s power adapter.

• The router comes with its own power adapter. Do not use another adapter.

• This class II adapter does not need to be grounded (earthed). The connection to the
electrical network should comply with the indications given on the label.

• Use a readily accessible AC power o utlet located near the router. The power supply cord is

1.5 m long.

• Care should be taken to ensure that the power cord is routed, so it is not likely to be walked
on or pinched by items placed upon or next to it.

• The router is designed to be connected to a GG- (ground-to-ground) or GN­(ground-to-neutral) type power supply network.

• The router is not designed to be connected to an electrical install ation with IT type diagram
(neutral connected to earth through an imped a nc e) .

• Protection against short-circuits and leaks between the phase, neutral and earth should be
provided by the building’s electr ical installation. The power supply circuit for this equipment
should be fitted with 16 A overcurrent protection and differential protection.

• Connect the router to th e AC powe r via a r eadily accessib le wall soc ket prov iding the electric
protection.

Location conditions

By choosing an appropria te l o cati on , you wi ll pr es erve t he lon ge vit y of t he d evi ce. Ens ur e that
the selected location has the following characteristics:

• Install and use the router inside a building.

• The room temperature must not exceed 40 °C.

• Solar radiation: 700 w/m².

• Relative humidity: 5 to 85 % without co ndensation.

• The router can be placed on a desktop or fixed vertically in its wall mount ing.

• Do not expose the router to strong sunlight or place it near a substantial source of heat.

• Do not place the router in an environment where it could be subjected to considerable steam
condensation.

• Do not expose the router to splashes of water.

4

F@ST 2704N

• Avoid blocking any vent openings or ex haust exits on this equipment. Do not place
equipment in a built-in installation such as a cabinet that may imp ede the flow of air through
the ventilation openings.

• Do not use the router or its peripherals for outdoor transmissions.

Maintenance

• This equipment is not user serviceable and is to be serviced by qualified personnel only.

• Do not disassemble this equipment. If service is required, disconnect all power and phones
lines from the equipment and consult qualified service personnel.

• Do not use liquid or aerosol cleaning agents.

Environment

Never dispose of your product with other household waste. Please inform
yourself about the local rules on the separate collection of electrical and
electronic products. The correct disposal of your old product helps prevent
potentially negative consequences on the environment and human health.

5