SAGEMCOM BROANDS FAST1704 Users Manual
Wireless ADSL Router
User Manual
Error! Style not defined.
Contents
1 Introduction...................................................................................2
1.1 Application....................................................................2
1.2 Environment Requirements........................................... 2
1.3 System Requirements....................................................3
1.4 Safety Cautions .............................................................3
1.5 LED Status Description................................................. 4
1.5.1 Front Panel ............................................................ 4
1.5.2 Rear Panel .............................................................5
2 Hardware Installation....................................................................5
2.1 Choosing the Best Location for Wireless Operation.....6
2.2 Connecting the ADSL Router........................................6
3 Introduction to Web Configuration................................................7
3.1 Logging In to the Modem..............................................7
3.2 Summary of Device Information...................................8
3.3 Advanced Setup.............................................................9
3.3.1 Configuring PPPoE ............................................... 9
3.3.2 Bridge Configuration...........................................14
3.3.3 Wireless – Basic..................................................16
3.3.4 Wireless – Security..............................................17
3.4 Management................................................................19
3.4.1 Settings................................................................19
3.4.2 System Log..........................................................21
3.4.3 TR-069 Client......................................................23
3.4.4 Access Control ....................................................23
3.4.5 Update Software..................................................24
3.4.6 Save/Reboot ........................................................25
4 Q&A............................................................................................ 26
i
Error! Style not defined.
1 Introduction
The Router is a highly ADSL2+ Integrated Access Device and can
support ADSL link with downstream up to 24 Mbps and upstream up
to 1 Mbps. It is designed to provide a simple and cost-effective
ADSL Internet connection for a private Ethernet or 802.11g/802.11b
wireless network. The Router combines high-speed ADSL Internet
connection, IP routing for the LAN and wireless connectivity in one
package. It is usually preferred to provide high access performance
applications for the individual users, the SOHOs, and the small
enterprises.
Network and Router management is done through the web-based
management interface that can be accessed through the local
Ethernet using any web browser. You may also enable remote
management to enable configuration of the Router via the WAN
interface.
1.1 Application
Home gateway
SOHOs
Small enterprises
TV over IP (IPTV)
Higher data rate broadband sharing
Shared broadband internet access
Audio and video streaming and transfer
PC file and application sharing
Network and online gaming
1.2 Environment Requirements
Operating temperature: 0ºC~45ºC
Storage temperature: -10ºC~55ºC
2
Operating humidity: 10%~95%, non-condensing
Error! Style not defined.
Storage humidity: 5%~95%, non-condensing
Power adapter input: 100V~240V AC, 50/60Hz
Power adapter output: 12V DC, 0.8A
1.3 System Requirements
Recommended system requirements are as follows:
Pentium 233 MHZ or above
Memory: 64 Mbps or above
10M Base-T Ethernet or above
Windows 9x, Windows 2000, Windows XP, Windows ME,
Windows NT
Ethernet network interface card
1.4 Safety Cautions
Follow the announcements below to protect the device from risks
and damage caused by fire and electric power.
Use volume labels to mark the type of power.
Use the power adapter that is packed within the device package.
Pay attention to the power load of the outlet or prolonged lines.
An overburden power outlet or damaged lines and plugs may
cause electric shock or fire accident. Check the power cords
regularly. If you find any damage, replace it at once.
Proper space left for heat radiation is necessary to avoid any
damage caused by overheating to the device. The holes are
designed for heat radiation to ensure that the device works
normally. Do not cover these heat radiant holes.
Do not put this device close to a place where a heat source exits
or high temperature occurs. Avoid the device from direct
sunshine.
Do not put this device close to a place where is over damp or
watery. Do not spill any fluid on this device.
Do not connect this device to any PC or electronic product,
unless our customer engineer or your broadband provider
3
instructs you to do this, because any wrong connection may
Error! Style not defined.
cause any power or fire risk.
Do not place this device on an unstable surface or support.
1.5 LED Status Description
1.5.1 Front Panel
Indicator Status Description
Power
ADSL
Internet
LAN1/2/3/4
WLAN Off No radio signal is detected.
Off The power is off.
Green
Red
Blink Red Upgrading software.
Off No signal is detected.
Slow Blink Green The DSL line is transferring.
Fast Blink Green The DSL line is training.
Green The DSL line connection is established.
Off No PPPoA or PPPoE connection
Green
Red
Off No Ethernet signal is detected.
Blink Green
Green Ethernet interface is ready to work
The power is on and the device operates
normally.
The power is self-testing.
The device enters the console mode of
the boot loader.
The self-testing of the power fails if the
LED is always red.
The PPPoA or PPPoE connection is
established. The users can access the
Internet.
Device attempts to become IP
connected but fails (no DHCP response,
no PPPoE response, PPPoE
authentication failed, no IP address
from IPCP, etc.)
The user data is passing through
Ethernet port.
4
Indicator Status Description
Error! Style not defined.
Blink Green
Green WLAN interface is ready to work.
The user data is passing through
WLAN port.
1.5.2 Rear Panel
Interface Description
Wireless antenna.
Line
LAN 1~4
Power
Reset
WLAN/WPS
On/Off Power switch.
RJ-11 port, using the telephone line to connect the
modem with the ADSL cable or splitter.
RJ-45 port, connect the modem to a PC or other
network device.
Power supplied port, plug in for power adapter that the
power input is 12V DC, 1 A.
To restore the factory default, keep the device powered
on and push a needle into the hole. Press down the
button about 3 seconds and then release.
Press the button silently less than 1s to enable
WLAN function.
Press the button for more than 5s to enable to
enable WPS function.
If you press the button between 1s and 5s, no
function takes effective.
2 Hardware Installation
5
Error! Style not defined.
2.1 Choosing the Best Location for
Wireless Operation
Keep the numbers of walls and ceilings to the minimum:
The signal emitted from wireless LAN devices can penetrate
through ceilings and walls. However, each wall or ceiling can
reduce the range of wireless LAN devices from 1 ~ 30 miters.
Position your wireless devices so that the number of walls or
ceilings obstructing the signal path is minimized.
Consider the direct line between access points and workstations:
A wall that is 0.5 meters thick, at a 45-degree angle appears to
be almost 1 meter thick. At a 2-degree angle, it appears over 14
meters thick. Be careful to position access points and client
adapters so the signal can travel straight through (90º angle) a
wall or ceiling for better reception.
Building materials make difference:
Buildings constructed using metal framing or doors can reduce
effective range of the device. If possible, position wireless
devices so that their signals can pass through drywall or open
doorways. Avoid positioning them in the way that their signal
must pass through metallic materials. Poured concrete walls are
reinforced with steel while cinderblock walls generally have
little or no structural steel.
Position the antenna for best reception:
Play around with the antenna position to see if signal strength
improves. Some adapters or access points allow you to judge
the strength of the signal.
Keep your product away (at least 1~2 meters) from electrical
devices:
Keep wireless devices away from electrical devices that
generate RF noise such as microwave ovens, monitors, electric
motors, etc.
2.2 Connecting the ADSL Router
6
See the following figure. Connect the Line port of the DSL
Error! Style not defined.
Router with a telephone cable.
Connect the LAN port of the DSL Router to the network card of
the PC via an Ethernet cable.
Plug one end of the power adapter to the wall outlet and connect
the other end to the PWR port of the DSL Router.
The following figure displays the connection of the DSL Router, PC,
and telephones.
3 Introduction to Web Configuration
3.1 Logging In to the Modem
Step 1 Open a Web browser on your computer.
Step 2 Enter http://192.168.1.1 (DSL router default IP address) in
the address bar. The login page appears.
Step 3 Enter a user name and the password. The default username
and password of the super user are admin and admin. The
username and password of the common user are user and
user. You need not enter the username and password again
if you select the option Remember my password. It is
7
recommended to change these default values after logging in
Error! Style not defined.
to the DSL router for the first time.
Step 4 Click OK to log in or click Cancel to exit the login page.
3.2 Summary of Device Information
8
Default Gateway: In the bridging mode there is no gateway. In
Error! Style not defined.
other modes, it is the address of the uplink equipment, for
example, PPPoE/PPPoA.
DNS Server: In the PPPoE / PPPoA mode, it is obtained from
the uplink equipment. In the bridging mode, there is no DNS
Server address and you can manually enter the information.
3.3 Advanced Setup
Choose Advanced Setup > WAN, and the following page appears.
3.3.1 Configuring PPPoE
Step 1 Click Add and the following page appears. In this page, you
can modify VPI/VCI, service categories, and QoS.
9
Loading...