MyCK100 handsfree kit User Guide
Introduction
MyCK100 handsfree kit is a handsfree kit based on Bluetooth® technology.
Bluetooth® technology is a standard for wireless, short range communication. Devices such as a
handsfree kit and a mobile phone can communicate together without wires within an approximately 10 m
radius.
MyCK100 handsfree kit is a Bluetooth® approved handsfree kit, in accordance with 1.2 revision of
Bluetooth® protocol. Two profiles are supported: headset & handsfree, so devices supporting either
headset or handsfree profile can be used with this handsfree kit.
In order to check compatibility of Bluetooth® devices with MyCK100 handsfree kit, please log on to:
www.sagem.com/mobiles
.
This guide focuses on MyCK100 handsfree kit usage with Bluetooth® mobile phone, which is the most
common application.
Your MyCK100 handsfree kit allows you to receive phone calls, make phone calls (if your handset
supports voice-activated features) and set up call volume and ring volume directly on your handsfree kit.
MyCK100 handsfree kit is fitted with the following keys below:
• A main push button §
• A volume cutting wheel
• A microphone cutting wheel
• Two buttons button 1 (Logo ON/OFF) and button 2 (Logo Mute) (These buttons are used for
pairing etc…)
Before starting using MyCK100 handsfree kit, you should charge the handsfree kit 's battery; please refer
to the section Charging MyCK100 handsfree kit of this guide.
Before pairing the MyCK100 handsfree kit with a mobile phone please refer to the section Pairing of
MyCK100 Bluetooth handsfree kit of this guide.
Box content
Please make sure that in addition to this guide you have:
- MyCK100 handsfree kit,
- 3 clips,
- Charger,
- Charging Adapter,
- A soft bag
Interface
Charging MyCK100 handsfree kit
Upon reception your handsfree kit is not charged. Before first use, you therefore need to recharge it
completely during approx. 8 hours using provided charger and charging adapter. Next recharge should
last approx. 2h 30 minutes.
If you hear 1 beep each minutes in your handsfree kit and light indicator flashes in red each 30 s,
handsfree kit needs to be recharged.
Please connect the charging adapter on one side to the handsfree kit and on the other side to the power
charger, which you can then connect into a mains plug.
Light indicator is red during charging process and turns blue after completion.
During the charge you can used your handsfree kit.
Please note use of any other charger will cancel the handsfree kit warranty. The handsfree kit shall
operate as normal during Charging Mode (such as receiving call, accept call etc).
To ensure a maximal life time to the battery, it is recommended to recharge the battery only when it gets
completely empty. Life cycle should allow approx. 500 charge & discharge cycles
If your handsfree kit is left with low battery for a long time, battery may get into overdischarge. In such
case, you may need to charge your battery during up to 10 hours before it recovers a full charge
Don't leave the charger connected to the headset more than 24 hours.
The MyCK100 handsfree kit has a protection in temperature activated during the charge. The charge will
be stopped under 0°C and over 55 °C in order to ensure a maximal life time to the battery
Button 1
Button 1
(On/Off)
Button 2
(Mute)
Main push
button
§
Volume cutting
wheel
Note : Short press is an instantaneous press. Medium-long press is between 2 s
and 5s. Long press exceed 5s
Microphone
cutting wheel
Switching ON/OFF the myCK100 handsfree kit
The myCK100 handsfree kit will be switched on (from off state) by doing a medium-long press on Button
1. A short low tone beep followed by 1 high low tone beep is played by the handsfree kit.
The myCK100 handsfree kit will be switched off (from on state) by doing a medium-long press on Button
1. A short high tone beep followed by 1 short low tone beep is played by the handsfree kit.
Pairing of myCK100 Bluetooth handsfree kit
Before using the myCK100 handsfree kit, you must pair it with your Bluetooth® mobile phone. Pairing is
the process of linking two Bluetooth® devices, so that they can communicate.
The pairing procedure only needs to be done once. Afterwards, every time you switch on your handsfree
kit (Push medium-long on Button 1), it will automatically connect to your mobile phone. If the user loses
the Bluetooth® connection with his mobile (Ex: An user leaves the handsfree kit in his car and takes his
mobile phone with him). The user should push once the main push button § to connect the handsfree kit
with his Bluetooth® mobile phone. If you pair your Bluetooth® mobile phone with another Bluetooth®
device, you will have to pair the handsfree kit with your phone again before use.
IMPORTANT: Before pairing, all Bluetooth® devices must be switched off.
To initiate the pairing, put both the myCK100 handsfree and the mobile phone within 0.3 meter (1 foot) of
each other. Make sure there is no Wi-Fi equipment operating in the vicinity.
1. Switch on the myCK100 handsfree kit (Push medium-long on Button 1). Pairing will be
automatically initated by the myCK100 handsfree kit itself when detecting no pairing history
list (No mobile phone paired, yet). The handsfree kit will indicate the pairing Mode by
alternately blinking blue and red LED indicator in every 1-second interval.
If a mobile phone is already listed in the handsfree kit. The handsfree kit enters in pairing
Mode after a long press on button 2. The Pairing Mode is indicated by alternately blinking
blue and red LED indicator in every 1-second interval. If your Bluetooth® mobile phone is
switched off the handsfree kit stays in pairing mode around 3 minutes.
2. Switch on your phone and select the Bluetooth® mode (Service discovery) on the Mobile
phone (See the Bluetooth® mobile phone user guide).
3. Once the mobile phone detects the myCK100 handsfree kit, a message is displayed with
the following information: myCK100.
4. Follow the phone instructions to accept the pairing. The PIN code (or password) is 0000
5. When
the pairing is completed, the indicator light are not activated and a short bip tone is
played. Then short high bip tone is played in 2-second interval until connection is
established or failed.
6. The user could check if the myCK100 handsfree kit is connected to his Bluetooth® mobile
phone in pushing the main push button § (Short press). Then the handsfree kit plays a short
and a long bip tone. If the connection is failed the handsfree kit plays a short and a short
high bip tone.
Loading...