Ryobi RY15124 User Manual [fr, en, es]

OPERATOR’S MANUAL

ELECTRIC POWER HEAD

BLOC-MOTEUR DE ÉLECTRIQUE CABEZAL MOTOR ELÉCTRICA

RY15124

ALL VERSIONS

TOUTES LES VERSIONS TODAS LAS VERSIONES

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

Your power head has been engineered and manufactured to our high standard for dependability, ease of operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

SAVE THIS MANUAL FOR FUTURE REFERENCE

Ce bloc-moteur a été conçu et fabriqué conformément à nos strictes normes de fiabilité, simplicité d’emploi et sécurité d’utilisation. Correctement entretenu, cet outil vous donnera des années de fonctionnement robuste et sans problème.

AVERTISSEMENT : Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre le manuel d’utilisation avant d’employer ce produit.

Merci de votre achat.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

Su cabezal motor ha sido diseñado y fabricado de conformidad con nuestras estrictas normas para brindar fiabilidad, facilidad de uso y seguridad para el operador. Con el debido cuidado, le brindará muchos años de sólido funcionamiento y sin problemas.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes de usar este producto.

Le agradecemos su compra.

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

See this fold-out section for all of the figures referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras a las que

se hace referencia en el manual del operador.

Fig. 1

A - Coupler (coupleur, acoplador) B - Front handle (poignée avant, mango

delantero)

C - Switch trigger (gâchette de commutateur,

gatillo del interruptor) D - Rear handle (poignée arrière, mango trasero) E - Cord retainer (retenue de cordon, retén para

el cordón) F - Cord bend relief (soulagement de torsion du

cordon, protector del cordón) G - Lock-out button (bouton de verrouillage,

botón del seguro de apagado)

Fig. 2

A - Button (bouton, botón) B - Guide recess (logement guide, hueco guía) C - Coupler (coupleur, acoplador) D - Power head shaft (arbre du bloc moteur, eje

del cabezal motor) E - Knob (bouton, perilla) F - Positioning hole (trou de positionnement,

orificio de posicionamiento) G - Attachment shaft (arbre d’accessoire, eje del

aditamento)

Fig. 3

Fig. 4

A - Cord retainer (retenue de cordon, retén para

el cordón)

Fig. 5

Fig. 6

A - Switch trigger (gâchette de commutateur,

gatillo del interruptor)

B - Lock-out button (bouton de verrouillage,

botón del seguro de apagado)

Fig. 7

PROPER STRAIGHT SHAFT TRIMMER

ATTACHMENT OPERATING POSITION

ACCESSOIRE TAILLE-BORDURES À ARBRE

DROIT POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO

DE ADITAMENTO PARA RECORTADORA

DE EJE RECTO

A - Bolt (boulon, perno) B - Front handle (poignée avant, mango

delantero) C - Washer (rondelle, arandela) D - Wing nut (écrou papillon, tuerca de

mariposa)

A - Cord retainer (retenue de cordon, retén para

el cordón)

PROPER BLOWER ATTACHMENT

OPERATING POSITION

ACCESSOIRE SOUFFLANTE

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

MANEJO DE ADITAMENTO PARA SOPLADOR

Fig. 10Fig. 8

PROPER PRUNER ATTACHMENT

OPERATING POSITION

ACCESSOIRE ÉLAGUEUSE POSITION

DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO DE

ADITAMENTO PARA PODADORA

Fig. 12

PROPER CURVED SHAFT TRIMMER

ATTACHMENT OPERATING POSITION

ACCESSOIRE TAILLE-BORDURES À ARBRE

COURBÉE POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL MANEJO

DE ADITAMENTO PARA RECORTADORA

DE EJE CURVO

Fig. 9 Fig. 11

PROPER TILLER ATTACHMENT

OPERATING POSITION

ACCESSOIRE CULTIVATEUR

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

MANEJO DE ADITAMENTO PARA CULTIVAR

ACCESSOIRE COUPE-BORDURES

ACCESORIO PARA CORTAR BORDES

PROPER EDGER ATTACHMENT

OPERATING POSITION

POSITION DE TRAVAIL

POSICIÓN CORRECTA PARA EL

iii

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................ 3-4

Instructions importantes concernant la sécurité / instrucciones de seguridad importantes

Symbols ......................................................................................................................................................................... 5-6

Symboles / Símbolos

 Electrical ........................................................................................................................................................................6-7

Caractéristiques électriques / Aspectos eléctricos

 Features ............................................................................................................................................................................7

Caractéristiques / Características

 Assembly .......................................................................................................................................................................7-8

Assemblage / Armado

 Operation .....................................................................................................................................................................9-10

Utilisation / Funcionamiento

 Maintenance ................................................................................................................................................................... 10

Entretien / Mantenimiento

 Troubleshooting .............................................................................................................................................................. 10

Dépannage / Solución de problemas

 Warranty .........................................................................................................................................................................11

Garantie / Garantía

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

IMPORTANT SAFETY INSTRUCTIONS

WARNING!

Read and understand all instructions before using this product. Failure to follow all instructions listed below may

result in electric shock, fire and/or serious personal injury. Do not use without guard and handle in place.

READ ALL INSTRUCTIONS

For safe operation, read and understand all instructions

before using this product. Follow all safety instructions. Failure to follow all safety instructions listed below, can result in serious personal injury.

Do not allow children or untrained individuals to use this

unit.

Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the machine.

Use Safety Glasses – Always wear eye protection with

side shields marked to comply with ANSI Z87.1. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.

Always wear safety glasses with side shields. Everyday

glasses have only impact resistant lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury. Use face mask if operation is dusty.

 Dress Properly – Use rubber gloves and substantial

footwear is recommended when working outdoors. Wear heavy long pants, long sleeves, boots, and gloves. Do not wear loose-fitting clothing, short pants, sandals, jewelry of any kind, or go barefoot.

Secure long hair above shoulder level to prevent

entanglement in moving parts.

Keep children away – Keep all bystanders, children, and

pets at least 50 ft. away.

Stay alert – Do not operate this unit when you are tired,

ill, or under the influence of alcohol, drugs, or medication.

Do not operate in poor lighting. Keep all parts of your body away from any moving part. Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.

To reduce the risk of electric shock, this tool has a polarized

plug (one blade is wider than the other) and will require the use of a polarized extension cord. The plug will fit into a polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not

fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug, extension cord receptacle, or extension cord plug in any way.

Avoid body contact with grounded surfaces such as pipes,

radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded.

Avoid Dangerous Environments – Don’t expose power

tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

Warning – To reduce the risk of electric shock - Use

outdoor extension cords marked W-A, W, SW-A, SOW-A, STW-A, STOW-A, SJW-A, SJTW-A, or SJTOW-A. These cords are rated for outdoor use and reduce the risk of electric shock.

Ground Fault Circuit Interrupter (GFCI) protection should

be provided on the circuit(s) or outlet(s) to be used for the gardening appliance. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.

Use Right Appliance - Do not force tool. Use the correct

tool for your application. The correct tool will do the job better and safer at the rate for which it is designed.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear protective footwear that will protect your feet and improve your footing on slippery surfaces.

Do not use on a ladder or unstable support. Stable footing

on a solid surface enables better control of the unit in unexpected situations.

Do Not Overreach – Keep firm footing and balance.

Overreaching can result in loss of balance.

 Avoid Unintentional Starting – Do not carry plugged in

appliance with finger on trigger. Be sure the switch trigger is not engaged before plugging in.

Do not use tool if switch trigger does not turn it on or off.

Any tool that cannot be controlled with the switch trigger is dangerous and must be repaired.

Disconnect Appliance – Remove appliance from power

source before storing, servicing, changing accessories such as cutting line. Such preventive safety measures reduce the risk of starting the tool accidentally.

Use only identical manufacturer’s replacement parts and

accessories. Use of any other parts may create a hazard or cause product damage.

 Maintain appliance with care – Replace string head if

cracked, chipped, or damaged in any way. Be sure the string head is properly installed and securely fastened. Keep cutting edge sharp and clean for best performance and to reduce the risk of injury. Follow instructions for lubricating and changing accessories. Inspect appliance cord periodically, and if damaged, have it repaired by an authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry,

3 — English

IMPORTANT SAFETY INSTRUCTIONS

clean, and free from oil and grease. Failure to do so can cause serious injury.

 Make sure all guards, straps, deflectors and handles are

properly and securely attached.

 Never use flailing devices, wire, or rope on any attachment.  Use only the manufacturer’s replacement string in the

cutting head when using a string trimmer attachment. Do not use any other cutting attachment, for example, metal wire, rope, or the like. To install any other brand of cutting head to the string trimmer can result in serious personal injury.

Never operate unit without the grass deflector in place

and in good condition.

 Check damaged parts – Before further use of the tool, a

guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury.

 Maintain a firm grip on both handles while trimming. Keep

string head below waist level. Never cut with the string head located over 30 in. or more above the ground.

Store idle appliances - When not in use, power head

should be stored indoors in a dry, locked place out of the reach of children. Do not allow appliance to be used as a toy. Close attention is necessary when used near children.

Extension Cord - Make sure your extension cord is in

good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of at least 14 is recommended for an extension cord 50 feet or less in length. A cord exceeding 100 feet is not recom mended. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Turn off controls before unplugging.

Keep the air vents clean and free of debris to avoid

overheating the motor. Clean after each use.

Stop the unit and disconnect the power source when not

in use. Carry the unit with the motor stopped.

Store unplugged and out of the reach of children when

not in use.

Do not hang unit so that the switch trigger is depressed. Do not use multiple cords. Do not abuse the cord – Never carry the unit by the

extension cord or yank extension cord to disconnect unit. Keep the cord clear of operator and obstacles at all times. Do not expose cords to heat, oil, water, or sharp edges. Do not handle plug with wet hands.

 If the power supply cord is damaged, it must be replaced

only by the manufacturer or by an authorized service center to avoid risk.

If appliance is not working as it should , has been dropped,

damaged, dropped into water, return it to service center.

Don’t grasp the exposed cutting blades or cutting edges

when picking up or holding the appliance.

Don’t Force Appliance – It will do the job better and with

less likelihood of a risk of injury at the rate for which it was designed.

Danger – Risk of Cut – Keep Hands Away From Blades –

Keep both hands on handles when power is on. Do not attempt to remove cut material nor hold material to be cut when blades are moving. Make sure trimmer switch is off when clearing jammed material from blades.

Caution – blades coast after turn off. When operating the trimmer keep extension cord behind

trimmer.

Do not put any objects into openings. Do not use with

any openings blocked, keep free of dust, lint, hair and anything that may reduce air flow.

Save these instructions. Refer to them frequently and

use them to instruct others who may use this power tool. If you loan someone this power tool, loan them these instructions also.

ADDITIONAL SPECIFIC SAFETY RULES CAN BE FOUND IN THE

APPLICABLE ATTACHMENT’S OPERATOR’S MANUAL

4 — English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

WARNING:

CAUTION:

NOTICE:

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury.

(Without Safety Alert Symbol) Indicates important information not related to an injury hazard, such as a situation that may result in property damage.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert

Read Operator’s Manual

Indicates a potential personal injury hazard.

To reduce the risk of injury, user must read and understand operator’s manual before using this product.

Eye Protection

Wet Conditions Alert

Keep Bystanders Away

Ricochet

No Blade

Alternating Current

Direct Current

Class II Construction

Do not expose to rain or use in damp locations.

Keep all bystanders at least 50 ft. away.

Thrown objects can ricochet and result in personal injury or property damage.

Do not install or use any type of blade on a product displaying this symbol.

Type of current

Type or a characteristic of current

Double-insulated construction

5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

min

Volts

Amperes

Hertz

Watt

Minutes

Voltage

Current

Frequency (cycles per second)

Power

Time

ELECTRICAL

DOUBLE INSULATION

Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual threewire grounded power cord. All exposed metal parts are isolated from the internal metal motor components with protecting insulation. Double insulated tools do not need to be grounded.

WARNING:

The double insulated system is intended to protect the user from shock resulting from a break in the tool’s internal insulation. Observe all normal safety precautions to avoid electrical shock.

NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the system and should be performed only by a qualified service technician. For service, we suggest you return the product to your nearest authorized service center for repair. Always use original factory replacement parts when servicing.

ELECTRICAL CONNECTION

This product has a precision-built electric motor. It should be connected to a power supply that is 120 V, AC only (normal household current), 60 Hz. Do not operate this product on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the product does not operate when plugged into an outlet, double-check the power supply.

GFCI

Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or outlet(s) to be used for the product. Receptacles are available having built-in GFCI protection and may be used for this measure of safety.

EXTENSION CORDS

When using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to handle the current the product will draw. An undersized cord will cause a drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.

6 — English

ELECTRICAL

When working outdoors with a product , use an extension cord that is designed for outside use. This type of cord is designated with “W-A” or “W” on the cord’s jacket.

Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

WARNING:

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools, or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

25’ 16 16 16 16 14 14

50’ 16 16 16 14 14 12

100’ 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

WARNING:

Check extension cords before each use. If damaged replace immediately. Never use the product with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

FEATURES

PRODUCT SPECIFICATIONS

Operating RPM .................................................................................................................................................10,745 (RPM)

Input ....................................................................................................................................120 V, 60 Hz, AC only, 10 Amps

KNOW YOUR PRODUCT

See Figure 1.

The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features and safety rules, in both this manual and the operator’s manuals for all attachments that your are using with this power head.

CORD RETAINER

The cord retainer helps prevent accidental unplugging of the extension cord.

LOCK-OUT BUTTON

The lock-out button reduces the possibility of accidental starting.

FRONT HANDLE

The power head is equipped with a front handle assembly for ease of operation and to prevent loss of control.

ASSEMBLY

UNPACKING

This product requires assembly.  Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the packing list are already assembled to your product when you unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer installation. Use of a product that may have been improperly assembled could result in serious personal injury.

7 — English

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-860-4050 for assistance.

PACKING LIST

Power Head Front Handle with Hardware Operator’s Manual

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this product with damaged or missing parts could result in serious personal injury.

WARNING:

Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious personal injury.

INSTALLING AN ATTACHMENT TO THE POWER HEAD

See Figure 2.

WARNING:

Read and understand entire Operator’s Manual for each optional attachment used on this power head and follow all warnings and instructions. Failure to follow all instructions may result in electric shock, fire and/or serious personal injury.

This electric power head may be used with only the following Ryobi Expand-It attachments:

RY15518 Edger RY15520 Pruner RY15523 Straight Shaft String Trimmer RY15525 Curved Shaft String Trimmer RY15550 Tiller RY15519 Blower NOTE: When using string trimmer attachments, use only

.080 in. diameter line. The attachment connects to the power head by means of

a coupler device.

 Unplug the power head.  Loosen the knob on the coupler and remove the hanger

cap from the attachment.

 Push in the button located on the attachment shaft. Align

the button with the guide recess on the power head coupler and slide the two shafts together. Rotate the attachment shaft until the button locks into the positioning hole.

 NOTE: If the button does not release completely in the

positioning hole, the shafts are not locked into place. Slightly rotate from side to side until the button is locked into place.

 Tighten the knob securely.

WARNING:

Be certain the knob is fully tightened before operating equipment; check it periodically for tightness during use to avoid serious personal injury.

WARNING:

This electric power head is designed to be only used with the attachment models that are specified in this Operator’s Manual. It is not designed to be used with brush cutters or other attachment models. Use of other attachments could cause serious personal injuries or property damage.

WARNING:

Never install, remove, or adjust any attachment while power head is running. Failure to stop the motor can cause serious personal injury. Never operate power head without an attachment.

8 — English

ATTACHING THE FRONT HANDLE

See Figure 3.

 Unplug the power head.  Press the front handle onto the power head shaft so that

the handle is angled toward the rear handle.

 Place the front handle along the power head shaft to a

position that allows for comfortable operation.

 Slide the bolt through the holes in the front handle.  Slide the washer onto the bolt.  Place the wing nut onto the bolt and tighten the wing nut

securely.

OPERATION

WARNING:

Do not allow familiarity with product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to comply with ANSI Z87.1. Hearing and/or head protection may also be required depending on the type of attachment used and as prescribed in the attachment’s Operator’s Manual. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING:

Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

CONNECTING TO POWER SUPPLY

See Figure 4 -5.

The power head is designed with a cord retainer that prevents the extension cord from being pulled loose while using.

 Form a loop with the end of the extension cord.  Insert loop portion of extension cord through opening in

the bottom of the rear handle and place over cord retainer.

 Slowly pull loop against cord retainer until the slack is

removed.

 Plug power head into extension cord. NOTE: Failure to remove all excess cord slack from extension

cord retainer could result in plug loosening from receptacle.

LOCK-OUT BUTTON

See Figure 6.

The lock-out button reduces the possibility of accidental starting. The lock-out button is located on the handle above the switch trigger. The lock-out button must be depressed before you pull the switch trigger. The lock resets each time the trigger is released.

STARTING AND STOPPING THE POWER HEAD

See Figure 6.

 To start the power head: Depress the lock-out button and

squeeze the switch trigger.

 To stop the power head: Release the switch trigger.

OPERATING THE POWER HEAD

See Figures 7 - 13.

WARNING:

Motor housing may become hot during operation. Do not rest or place your arm, hand, or any body part against the motor housing during operation. Only hold the unit as shown in figures 7 - 13 (depending on attachment used) during trimmer operation with all body parts clear of motor housing (or as shown in the applicable attachment Operator’s Manual). Extended contact with the motor housing may result in burns or other injuries.

WARNING:

Always position the unit on the operator’s right side. The use of the unit on the operator’s left side will expose the user to hot surfaces and can result in possible burn injury.

WARNING:

To avoid burns from hot surfaces, never operate unit with the bottom of the motor above waist level.

Hold the power head with your right hand on the rear handle and your left hand on the front handle. Keep a firm grip with both hands while in operation. Power head should be held at a comfortable position with the rear handle about hip height.

Always operate power head at full throttle. If debris becomes wrapped around the attachment, RELEASE THE SWITCH TRIGGER, unplug the unit, and remove the debris.

9 — English

+ 23 hidden pages