Ryobi RPP720G Operator's Manual
RPP720G
ELECTRIC POLE PRUNER
OPERATOR’S MANUAL
It is essential that you read the instructions in this manual before
operating this machine.
Subject to technical modications.
ENGLISH
GENERAL SAFETY RULES
WARNING
When using electric gardening appliances, basic
safety precautions should always be followed to
reduce the risk of fire, electric shock and personal
injury, including the following:
nThis appliance is not intended for use by persons
(including children) who have limited understanding
or lack of experience and control, unless they have
been given supervision or instruction concerning the
use of the appliance by a person responsible for their
safety.
n Children should be supervised to ensure that they do
not play with the appliance.
ELECTRICAL SAFETY INSTRUCTIONS
nUse transport guard during transport and storage.
nThe machine must be cleaned and maintained before
storage.
nSecure the unit during transport to prevent loss of oil,
injury or damage.
n Local regulations may restrict the age of the operator.
nDo not use the machine in any position that causes
any part to come within 15m of overhead electrical
lines.
nThe operator should wear slip-resistant foot
protection as well as close fitting clothes, the use of
PPE and the need for adequate training, with PPE
including of hearing protection, eye protection, and
head protection .
nDo not use the unit if you are tired, ill or under
influence of alcohol or other drugs
nHazards which may be encountered when using
the pruner and avoid them when carrying out typical
tasks, and keep bystanders away while operating the
machine.
n Beware of falling branches or those rebound after
hitting the ground, remove these branches in sections
and not operate in the dangerous positions.
nKeep a firm footing and balance during operation,
including the need to use the harness provided.
ADDITIONAL SAFETY RULES
nNever allow children or people unfamiliar with these
instructions to use the appliance.
n Only use in daylight or in good artificial light.
n The appliance should be inspected and maintained
regularly. Repairs should be carried out only by an
authorised repairer.
n For additional protection the installation of a residual
current device (RCD) with a rated residual operating
current not exceeding 30 mA is advisable.
n Remove plug immediately from main if the cord is
damaged or cut.
n After use, disconnect the machine from the mains
and check for damage.
n When not in use store the machine out of the reach of
children.
n Mains powered pruner should only be repaired by an
authorised repairer.
n Do not expose to moisture.
n Before use check the supply and extension cord for
signs of damage or ageing.
n If the cord becomes damaged during use, disconnect
the cord immediately from the supply.
DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
n Keep cords away from cutting elements.
nWARNING! Cutting elements continue to rotate after
motor is switched off.
ENGLISH
SYMBOLS
V Voltage
A Current
Hz Frequency (cycles per second)
W Power
hrs Time
Double-insulated construction
n
o
.../min Revolutions, strokes, surface speed, orbits etc., per minute
Rotational speed, at no load
Do not expose to rain or use in damp locations.
Precautions that involve your safety.
To reduce the risk of injury, user must read and understand operator’s manual before
using this product.
Wear eye protection when operating this equipment.
Wear ear protection when operating this equipment.
Wear non-slip, heavy-duty protective gloves when handling the pole saw and the blade.
Keep all bystanders at least 15m away.
Remove plug from the mains immediately if cable is damaged or cut.
Do not touch the moving blade.
Electrical hazard, at least 15m away from the overhead lines
Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements.
SPECIFICATIONS
Voltage :....................................................220-240V/50Hz
Power : ....................................................................720 W
Bar Length : ............................................... 200mm/ 8 inch
Chain Pitch :.............................................9.5mm/ 3/8 inch
Chain type : ............... Low Profile Skip Tooth Narrow Kerf
Weight : .................................................................... 3.5kg
Sound Pressure Level : .......................................89 dB(A)
Sound Power Level : .........................................105 dB(A)
Vibration level : ................................................... 2.44 m/s²
Loading...