Ryobi RLT26CDSN Original Instructions Manual
RLT26CDSN
TWO STROKE PETROL LINE TRIMMER
ORIGINAL INSTRUCTIONS
Important! It is essential you read the instructions in this manual before starting and
operating this machine.
Subject to technical modications.
English (Original Instructions)
GENERAL SAFETY WARNINGS
WARNING
Read and understand all instructions. Failure to
follow all instructions may result in serious personal
injury as well as damage to the product.
Physical Condition of the Operator. Do not operate
this product when tired, ill or under the influence of
alcohol, drugs or medication.
Clothing Requirements. Always wear long heavy
pants, boots and gloves. Do not wear loose clothing,
jewelry, short pants, sandals or go barefoot. Secure
hair so that it is above shoulder level to avoid
entanglement in moving parts.
Protective Accessories Requirements. Wear eye
and hearing protection when operating this product.
Before use, inspect the condition of the trimmer.
Replace damaged parts. Check for fuel leaks.
Make sure all fasteners are in place and secure.
Replace cutting attachment parts that are cracked,
chipped or damaged in any way. Make sure the
cutting attachment is properly installed and securely
fastened. Be sure the cutting attachment shield is
properly attached and in the position recommended
by the manufacturer. Use only flexible, non-metallic
line recommended by the manufacturer. For example,
never use wire or wirerope, which can break off and
become a dangerous projectile.
Proper Stance. Keep firm footing and balance. Do
not overreach. Keep the cutting attachment below
waist level. Keep all parts of your body away from the
rotating cutting attachment and hot surfaces.
Exhaust Gases. Never start or run the product inside
a closed room or building; breathing exhaust fumes
can cause illness or death.
Fueling. Mix and pour fuel outdoors where there are
no sparks and flames. Slowly remove the fuel cap only
after stopping the engine. Do not smoke while fueling
or mixing fuel. Wipe spilled fuel from the product.
Move at least 30ft. (9m) away from the fueling source
and site before starting the engine.
Work Area. Clear the area to be cut before each use.
Remove all objects, such as rocks, broken glass,
nails, wire or string, that can be thrown or become
entangled in the cutting attachment. Clear the area
of children, bystanders and pets. At a minimum, keep
all children, bystanders and pets outside a 50ft. (15m)
radius. Because there still may be a risk of injury to
bystanders from thrown objects, bystanders should
be encouraged to wear eye protection. If you are
approached while operating the product, stop the
engine and the cutting attachment.
Dangerous Environments. To avoid falling, do not
use the product in damp or wet locations.
Controlling the Product. During carburetor
adjustments, the cutting attachment may spin.
Therefore, you should wear protective equipment
and observe all safety instructions when adjusting
the carburetor. For products equipped with a clutch,
be sure the cutting attachment stops turning when the
engine idles. When the product is turned off, make
sure the cutting attachment has stopped before setting
down the product.
Use the Right Product. Use the product for the
intended purpose only.
Save these instructions. Refer to them frequently
and use them to instruct others who may use this
power tool. If you loan someone this power tool, loan
them these instructions also.
2
English (Original Instructions)
SYMBOLS
Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning.
Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
Safety alert
Read your operator’s
manual
Wear eye, hearing and
head protection
Keep bystanders away
Ricochet Danger of ricochet.
Boots Wear non-slip safety footwear when using the product.
Gloves Wear non-slip, heavy-duty gloves.
Indicates danger, warning or caution. It means attention!!!
Your safety is involved.
Your manual contains special messages to bring attention to
potential safety concerns as well as operating and servicing
information. Please read all the information carefully to ensure
satisfaction and safe use.
Wear eye, hearing and head protection when operating the
equipment.
Keep all bystanders, especially children and pets, at least 15m
from the operating area.
No smoking Do not smoke when mixing fuel or filling the fuel tank.
Petrol
Oil Use 2-stroke oil for air cooled engines.
Mix petrol and oil Mix the fuel mix thoroughly and also each time before refuelling.
No blade Do not install any type of blade on this unit.
Do not use toothed blade This unit is not intended for use with a toothed saw type blade.
Use regular unleaded petrol intended for motor vehicle use with an
octane rating of 91 ([R+M]/2) or higher. E10 is not recommended.
3
English (Original Instructions)
113
83
RPM Decal
Rotational direction and maximum speed of the shaft for the
cutting attachment.
Run position.
Set the choke lever to "Full" position.
Place the engine switch to the "I" position.
PRIME - press the primer bulb 10 times slowly.
Pull the starter rope to start.
Squeeze throttle trigger to start / run.
To stop the unit, place the engine switch to the "O" position.
Blade hazard Warning! Risk of getting cut; operate carefully.
Guaranteed sound pressure level and sound power level.
Regulatory Compliance Mark (RCM). This product meets
applicable regulatory requirements.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
4
Loading...