Ryobi RCD1802M User Manual [ru]

Page 1
RCD1802
original instructions
Compact Drill Driver
Page 2
Important!
It is essential that you read the instructions in this manual before operating this machine.
Subject to technical modications.
Page 3
Safety
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool’’ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. WORK AREA SAFETY
a. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
2. ELECTRICAL SAFETY a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords
increase the risk of electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location
is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. PERSONAL SAFETY a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that
have the switch on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.
g. If devices are provided for the connection of
dust extraction and collection facilities, ensure these are connected and properly used. Use of
dust collection can reduce dust-related hazards.
4. POWER TOOL USE AND CARE a. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/
or the battery pack from the power tool before making any adjustments, changing accessories or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of
children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous
in the hands of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
Page 4
Safety
are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits
etc, in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool
for operations different from those intended could result in a hazardous situation.
5. BATTERY TOOL USE AND CARE a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one
type of battery pack may create a risk of re when
used with another battery pack.
b. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and re.
c. When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together
may cause burns or a re.
d. Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
6. SERVICE a. Have your power tool serviced by a qualified
repair person using only identical replacement parts. This will ensure that the safety of the power
tool is maintained.
SPECIAL SAFETY RULES
WARNING
The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the product.
Wear ear protectors when drilling. Exposure to noise
can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■ Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
■ Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a
“live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
INTENDED USE
You may use this product for the purposes listed below:
Drilling in all types of wood
Drilling in ceramics, plastics, fiberglass and laminates
Drilling in metals
Mixing paint
MAINTENANCE
When servicing, use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or cause product damage.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.
Do not attempt to modify this tool or create accessories
not recommended for use with this tool.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing of as waste. The machine, accessories and packaging should be sorted for environmental-friendly recycling.
SYMBOL
Safety alert
Please read the instructions carefully before starting the machine.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Page 5
1
2
1
2
1 2
Getting started
4
Page 6
3
I
I
I
4
I
I
I
8
I
I
I
1
2
I
I
I
1
6
I
I
I
2
0
I
I
I
Getting started
5
Page 7
PRODUCT SPECIFICATIONS
Voltage 18 V
Chuck 2-13 mm
Switch Variable speed
No load speed (drill mode):
- Lo speed 0 - 440 min-
- Hi speed 0 - 1600 min-
Clutch 24 positions
Maximum torque 45 Nm
Maximum spade bit 38 mm
Weight - excluding battery pack 1.21 kg
BATTERY AND CHARGER
Compatible battery pack (not included)
Lithium-Ion BPL-1820
1
1
Nickel Cadmium ABP1801G
BPL-1815 BPL-18202PK RB18L13 RB18L15 RB18L26 RB18L40 RB18LL40
ABP1802G
Compatible charger (not included)
BCL14181H BCL14183H BCL1418 BCS618 BCL1418IV*
ACR1800 ACR1800G BCS618 BCL1418 BCL14181H BCL14183H BCL1418IV*
* for vehicles’ 12V DC outlets
Page 8
Techtronic Industries (Australia) Pty. Ltd.
Level 1, 660 Doncaster Road Doncaster, VIC 3108, Australia
Techtronic Industries New Zealand Ltd.
27 Clemow Drive Mt. Wellington, Auckland 1060, New Zealand
961152050-02c
Page 9
Loading...