EDP2521L DRILL PRESS
OWNERʼS OPERATION MANUAL
EDP2521L
N197
TABLE OF CONTENTS |
|
|
|
Table of Contents |
1 |
Specificatons |
1 |
Rules for Safe Operation |
2-5 |
Unpacking |
6 |
Loose Parts List |
6 |
Assembly |
7 |
Adjustment |
8-9 |
Operation |
9-10 |
Maintenance |
10 |
Troubleshooting |
11 |
|
|
PRODUCT SPECIFICATIONS |
|
|
|
Input |
250 watt |
No Load Speed |
625 - 2500 R.P.M. |
Drilling Capacity |
13 mm |
Chuck Capacity |
13 mm |
Spindle Taper |
MT2 |
Spindle Travel |
50 mm |
Spindle Speeds |
5 |
Table Size |
160 x 160 mm |
Base Size |
285 x 185 mm |
Weight |
21KG |
Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.
Page 1
RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and understand this operator’s manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your drill press works.
READ ALL INSTRUCTIONS
KNOW YOUR POWER TOOL. Read the operator’s manual carefully. Learn the applications and limitations as well as specific potential hazards related to this tool.
GUARD AGAINST ELECTRICAL SHOCK by preventingbodycontactwithgroundedsurfaces. For example:pipes, radiators, ranges, refrigerator enclosures.
KEEP GUARDS IN PLACE and in working order. Never operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use.
REMOVEADJUSTING KEYSAND WRENCHES.
Form habit of checking to see keys and adjusting wrenches are removed from tool before turning it on.
KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents.
AVOID DANGEROUS ENVIRONMENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations or expose them to rain. Keep work area well lighted.
KEEP CHILDREN AND VISITORS AWAY. All visitors should wear safety glasses and be kept a safe distance from work area.
MAKE WORKSHOP CHILD PROOF with padlocks, master switches, or by removing starter keys.
DONʼT FORCE THE TOOL. It will do the job better and safer at the rate for which it was designed.
USE THE RIGHT TOOL. Do not force the tool or attachment to do a job for which it was not designed.
USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating . A wire gauge size (A.W.G.) of at least 16 is recommended for an extension cord 8 metres or less in length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
INSPECT EXTENSION CORDS PERIODICALLY and replace if damaged.
WEAR PROPER APPAREL. Do not wear loose clothing, neckties, or jewelry that can get caught
in the tool’s moving parts and cause personal
injury. Nonslip footwear is recommended when working outdoors. Wear protective hair covering to contain long hair.
ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impactresistant lenses; they are NOT safety glasses.
PROTECT YOUR LUNGS. Wear a face or dust mask if the cutting operation is dusty.
PROTECTYOURHEARING.Wearhearingprotection during extended periods of operation.
DONʼTABUSE CORD. Never carry tool by the cord or yank it to disconnect from receptacle. Keep cord away from heat, oil, and sharp edges.
DONOTOVERREACH. Keep proper footing and balance at all times.
MAINTAINTOOLSWITHCARE.Keeptoolssharp and clean for best and safest performance. Follow instructionsforlubricatingandchangingaccessories.
NEVERLEAVETOOLRUNNINGUNATTENDED.TURN POWER OFF. Disconnectalltoolswhennotinuse, before servicing, or when changing attachments etc.
AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in.
USE RECOMMENDEDACCESSORIES. The use of improper accessories may cause risk of injury.
USE ONLY DRILL BITS that comply with SAA and rated greater than 2500 RPM.
CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged must be properly repaired or replaced by an authorised service centre to avoid risk of personal injury.
KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool.
INSPECT TOOL CORDS AND EXTENSION CORDS PERIODICALLY and, if damaged, have repaired by a qualified service technician. Stay constantly aware of cord location and keep it well away from the rotating wheel.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
Page 2
RULES FOR SAFE OPERATION
USE OUTDOOR EXTENSION CORDS. Use only extension cords with approved ground connection that are intended for use outdoors and so marked.
WARNING:
WhenservicinguseonlyidenticalRyobireplacement parts. Use of any other parts may create a hazard or cause product damage.
Do not operate the bench drill until it is completely assembled and installed according to the instructions.
Before turning on, ensure belt guard is down and the chuck is installed correctly.
Remove adjusting keys and wrenches before turning on power
Ensure the chuck key is removed from the chuck before turning on the power.
Ensure the drill bit is securely locked in the chuck using the key supplied.
Use recommended speed for drill bit size and workpiece material.
Keepbeltguardinplacewhilemachineisinoperation.
Use only recommended accessories.
Disconnect tool before changing drill bit and ensure switch is in the off position before plugging in.
Do not use bench drill in damp or wet conditions.
Do not overload tool.
Keep tool well maintained.
Never leave tool running unattended.
Adjust the table or depth stop to avoid drilling into the table.
RISKOFINJURYDUETOACCIDENTALSTARTING.
Donotuseinanareawherechildrenmaybepresent.
DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL, OR ANY MEDICATION.
ALWAYS STAY ALERT . Do not allow familiarity (gained from frequent use of your tool) to cause a mistake. ALWAYS REMEMBER that a careless fraction of a second is sufficient to inflict severe injury.
STAYALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush.
SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct other users. If you loan someone this tool, loan them these instructions also.
WARNING:
Somedustcreatedbypowersanding,sawing,grinding, drilling, and other construction activities contains chemicals know to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
. lead from lead-based paints.
. crystalline silica from bricks and cement and other masonry products, and
. arsenic and chromium from chemically-treated timber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
DOT NOT EXPOSE
TO RAIN OR USE IN
DAMP LOCATIONS
Page 3
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give, are not substitutes for proper accident prevention measures.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER:Failure to obey a safety warning will result in serious injury to yourself to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself ro to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.
IMPORTANT
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we suggest you return the tool to your nearest RYOBI AUTHORISED SERVICE CENTRE for repair. When servicing,use only identical Ryobi replacement parts.
WARNING:
Do not attempt to operate this tool until you have read thoroughly and understand completely all instructions, safety rules, etc. contained in this manual. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury. Save this operator’s manual and review frequently for continuing safe operation and instructing others who may use this tool.
WARNING:
Theoperationofanytoolcanresultinforeignobjectsbeingthrownintoyoureyes, which can result in severe eye damage. Before beginning power tool operation,always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
Page 4
Loading...