Rotronic HL-1D, BL-1D, TL-1D Manual

www.rotronic.com
English
12.8000.2201E
HL-1D / BL-1D / TL-1D
23
90
Short Instruction Manual
Data Logger for humidity, temperature, pressure and dewpoint (device version V4.0)
Congratulations on purchasing your new Rotronic BL-1D (humidity, temperature, pressure and dewpoint), HL-1D (humidity and temperature), TL-1D (temperature) data logger. Please read these short instructions carefully before using the device. These short instructions are limited to a description of the main functions and installation of the device.
HL-1D BL-1D TL-1D
Humidity x x Temperature x x x Pressure x Dewpoint x Storage capacit y (lines) 32,000 64,000
2 DIMENSIONS / CONNECTIONS
Type HL-1D Type BL-1D Type TL-1D
60
USB Mini-port (settings and data download )
Battery compartment (BAT.)
Logging inter val Storage Capacity Reached After
30 sec. 11 days 2 hours 5 min. 111 day s 30 min. 1 year 301 days 45 min. 2 years 270 days 60 min. >3 years
Please see also battery life time. Low battery threshold 2.6 V.
3 INSERTING / REPLACING THE BATTERY
The data log gers run on one CR2 batter y. To insert the batter y, open the BAT lid and insert the battery with the right polarity (+/-). When closing the lid, ensure that the O-ring is correctly positioned.
Low batter y voltage may result in incorrect measurement result s. As soon as the bat­tery symbol appears, the battery should be replaced.
4 OPERATION / DISPLAY
Display:
COMM: Appears when the device is connected to a computer MIN/MAX/AVG: Minimum, maximum or average value of the stored data
(function available only in LOG mode).
FULL: Appears when storage is full LOG: Appears when the logging function is active : Appears when the battery is low °C/°F: Temperature %RH: Relative humidity (BL-1D, HL-1D) hPa: Pressure (BL-1D) DP °C/°F: Dewpoint (BL-1D) Hi, Lo: Appears when temperature or humidity exceed the High Alarm
or Low Alarm threshold
4.1 START / STOP BUTTON
Press the button once to switch the device on or off (the device cannot be switched off in LOG mode). To start or stop data logging, press the START/ STOP button and hold it down until "LOG" appears on the display, or pro­gram the desired logging time using HW4.
4.2 MODE BUTTON
Every 5 seconds (default value), or when the MODE button is pressed, the display toggles between "Humidity & Temperature" and "Pressure & Dew­point". In LOG mode, press and hold down to display the MIN/MAX/ AVG of the stored data.
HL-1D/TL-1D: In LOG mode, press the button for a moment to display the MIN/MAX /AVG of the stored data
BL-1D:
Humidity &
Temperature
Press or
Time interval
Pressure &
Dew Point
Press > 2s
Press
Time interval Time interval Time interval
PressPress
Press
Press
Press
AVG 1MAX 1MIN 1
AVG 2MAX 2MIN 2
4.3 LED STATUS INDICATOR
In Log mode, the right-hand LED ashes green every 5 seconds. When the
alarm threshold has been exceeded, or if the battery is low, the left-hand
LED ashes red ever y 5 seconds.
5 SETTING / DISPLAY OF THE LOGGED DATA
Settings can be made, and logged data can be downloaded or displayed, only on a PC that hasthe Rotronic H W4 software installe d. The device is connected to the P C via a commercially available USB-to-USB mini-cable (AC0003) The cover of the USB port on the device can be opened with a coin. More detailed information about making settings via HW4 will be found in the device-manager Help document.
When the logger is used for the rst time, the clock must be synchronized.
6 TROUBLESHOOTING
Error Problem Solution
E02 Temperature is too low Permit ted ambient temperature:
-30..70 ° C
E03 Temperature is too high Per mitted ambient temperature:
-30...70 °C E31 Temperature sensor damaged Send the device in for repair E04 Error in temperature measurement Place the measurement device in a
normal environment E11 RH calibration error Carry out humidity calibr ation again E33 Circuit damaged Send the device in for repair
7 TECHNICAL DATA
Accuracy 23 °C ±5 °C ±3.0 %RH, ±0.3 °C , ±3 hPa Logging interv al 30 s...24 h Storage capacity 64,000 lines Function MIN / MAX / AVG Display LCD, 2 lines Display ref resh rate 5 sec. (default)
(in logg ing mode, equals the log ging interval)
LED indicators 2 LEDs; right-hand LED ashes green during data logging
Left-hand LED ashes red when thresholds are exceeded
or the batter y is low Communication USB mini-por t Software HW4 V3.4.1 or higher (BL-1D: V3.9 or higher)
included Range of application -30...70°C
0...100 %RH (non-condensing) Batter y 1 x CR2 Battery life 1 year (1 h logging inter val, room temperature) IP protection t ype IP67 Weight 85 g Dimensions 90 x 60 x 23 mm FDA/GMP compatibility FDA 21 CFR P art 11 / GAMP 5-compliant HW4 soft ware Standards EN 12830 Accessories Mini-USB cable AC0003 (included in xL-1D-SET)
www.rotronic.comDeutsch
12.8000.2201D
HL-1D / BL-1D / TL-1D
23
90
Kurzbedienungsanleitung
Datenlogger für Feuchte, Temperatur, Druck und Taupunkt (ab Geräteversion V4.0)
1 ALLGEMEINE BESCHREIBUNG
Herzlichen Glückwunsch zum Kauf eines neuen Rotronic BL-1D (Feuchte, Temperatur, Druck
und Taupunkt), HL-1D (Feuchte und Temperatur), T L-1D (Temperatur) Datenlog ger. Bitte lesen
Sie diese Kurzbedienungsanleitung genau durch, bevor Sie das Gerät in Betrieb nehmen. Diese Kurzbedienungsanleitung beschränkt sich auf die Beschreibung der wichtigsten Funk­tionen und der Installation des Gerätes.
HL-1D BL-1D TL-1D
Feuchte x x Temperatur x x x Druck x Taupunk t x Speicherkapazität (Linien) 32,000 64,000
2 ABMESSUNGEN / ANSCHLÜSSE
Typ HL-1D Typ BL-1D Typ TL-1D
60
USB-Mini Anschluss (Einstellungen und Datendownload)
Batteriefach (BAT.)
Log-Intervall Speicherkapazität er reicht nach
30 sec 11 Tage 2 Std. 5 min 111 Ta ge 30 min 1 Jahr 301 Tage 45 min 2 Jahre 270 Tage 60 min >3 Jah re
Bitte beachten Sie auch die Batterielaufzeit. Niedriger Batterieschwellenwert 2,6 V.
3 EINSETZEN ODER AUSTAUSCHEN DER BATTERIE
Die Datenlogger werden mit einer CR2-Batterie betrieben. Beim Einsetzen der Batterie, den BAT-Deckel öffnen und die Batterie mit der richtigen Polarität (+/-) einsetzen. Beim Schlie­ssen darauf achten, dass der O-Ring korrekt eingesetzt ist.
Bei niedriger Batteriespannung können falsche Messresultate entstehen. Sobald das Batteriesymbol erscheint, sollte daher die Bat terie gewechselt werden.
4 OPERATION / DISPLAY
Display:
COMM: erscheint, wenn das Gerät mit einem Computer verbunden ist MIN/MAX/AVG: Minimaler, maximaler oder durchschnittlicher Wert der gespeicherten
Daten (funktionier t nur im LOG-Modus)
FULL: erscheint, wenn der Speicher voll ist LOG: erscheint, wenn die Aufzeichnungsfunktion aktiv ist : erscheint, wenn die Bat terie schwach ist °C/°F: Temperatur %RH: Relative Feuchte (BL-1D, HL-1D) hPa: Dr uck (BL-1D ) DP °C/°F: Taupunkt (BL-1D) Hi, Lo: erscheint, wenn die Temperatur oder Feuchte über der High Alarm
oder Low Alarm Schwelle ist
4.1 START / STOP TASTE
Taste kurz drücken um das Gerät ein- auszuschalten (im LOG-Modus kann das Gerät nicht ausgeschaltet werden). Um eine Datenaufzeichnung zu star­ten oder zu stoppen, drücken Sie die START/STOP Taste so lange bis auf dem Display "LOG" angezeig t wird oder programmieren Sie mittels HW4 die ge­wünschte Aufnahmezeit.
4.2 MODE TASTE
Alle 5 Sekunden (Standartwert) oder eine kurze Betätigung der MODE Taste wechselt zwischen "Feuchte & Temperatur" und "Druck & Taupunkt" Anzei­ge. Im LOG-Modus lange drücken, um MIN/MAX/AVG der gespeicherten Daten anzuzeigen.
HL-1D/TL-1D: Im LOG-Modus Taste kurz drücken, um MIN/MA X/AVG der gespeicherten Daten anzuzeigen
BL-1D:
Humidity &
Temperature
Press or
Time interval
Pressure &
Dew Point
Press > 2s
Press
Time interval Time interval Time interval
PressPress
Press
Press
Press
AVG 1MAX 1MIN 1
AVG 2MAX 2MIN 2
4.3 LED STATUSANZEIGE
Im Log-Modus blinkt die rechte LED alle 5 Sekunden grün. Beim Über- oder
Unterschreiten der Alarmschwelle und bei schwacher Batterie blink t die lin­ke LED alle 5 Sekunden rot.
5 EINSTELLUNGEN / ANZEIGEN DER AUFGEZEICHNETEN DATEN
Einstellungen und das Herunterladen bzw. Anzeigen der aufgezeichneten Daten erfordert ei­nen PC, auf dem die Rotronic HW4-Software installiert ist. Die Verbindung zwischen Gerät und PC wird mit einem handelsüblichen USB zu USB-Mini-Kabel (AC0003) hergestellt. Der Deckel des USB Anschlusses am Gerät kann mit einer Münze geöffnet werden. Genauere Informati­onen zu Einstellungen über die HW4 benden sich im Hilfe-Dokument des Gerätemanagers.
Beim ersten Gebrauch des Loggers muss die Zeit synchronisiert werden.
6 PROBLEMBEHANDLUNG
Fehler Problem Lösung
E02 Temperatur ist zu niedrig Zulässige Umgebungstemperatur:
-30...70 °C
E03 Temperatur ist zu hoch Zulässige Umgebungstemperatur:
-30...70 °C
E31 Temperatursensor beschädigt Gerät zurück zur Reparatur E04 Fehler in der Temperaturmessung Platzieren Sie das Messgerät
in einer normalen Umgebung
E11 RH Kalibrierungsfehler Wiederholen Sie die Feuchtekalibrierung E33 Schaltung beschädigt Gerät zurück zur Reparatur
7 TECHNISCHE DATEN
Genauigkeit 23 °C ±5 °C ±3.0 %rF, ±0.3 °C, ±3 hPa Log-Intervall 30 s…24h Speicherkapazität 64'000 Linien Funktion MIN / MA X / AVG Display LCD 2 Zeilen Display Wiederholr ate 5 Sek. (Standard)
(im Aufnahmemodus gleich dem Log-Intervall)
LED Anzeige 2 LEDs, LED rechts blinkt grün bei Datenaufzeichnung
LED links blinkt rot bei Grenzwerten o. schwacher Batterie
Kommunikation USB-Mini A nschluss
Software HW4 V3.4.1 oder höher (BL-1D: V3.9 oder höher)
inklusive
Einsatzbereich -30 …70 °C
0…100 %rF (nicht betauend)
Batterie 1 x CR2
Batterielaufzeit 1 Jahr (1 h Log-Intervall, Raumtemperatur) IP-Schutzar t IP67
Gewicht 85 g Abmessungen 90 x 60 x 23 mm FDA-/GMP-kompatibel FDA 21 CFR Par t 11 / GAMP 5 konfor me Software HW4 Normen EN 12830 Zubehör Mini USB-Kabel AC0003 (im xL-1D-SET enthalten)
www.rotronic.comFrançais
12.8000.2201F
HL-1D / BL-1D / TL-1D
23
90
Mode d'emploi abrégé
Loggers de données pour l’humidité, la température, la pression et le point de rosée (à partir de la version d’appareil V4.0)
1 DESCRIPTION GÉNÉRALE
Tous nos remerciements pour l’achat d’un des nouveaux loggers de données Rotronic BL-1D (humidité, température, pression et point de rosée), HL-1D (humidité et température), TL-1D
(température). Veuillez lire avec attention ce manuel d’utilisation abrégé, avant de mettre
l’appareil en service . Ce mode d’emploi abrégé se limite à la des cription des fonctions essen ­tielles et à l’installation de cet appareil.
HL-1D BL-1D TL-1D
Humidité x x Température x x x Pression x Point de rosée x Capacité mémoire (lignes) 32,000 64,000
2 DIMENSIONS / RACCORDEMENTS
Type HL-1D Type BL-1D Type TL-1D
3 INSTALLATION OU CHANGEMENT DES PILES
Les loggers de données sont alimentés par une pile CR2. Pour installer la pile, ouvrir le cou­vercle BAT et poser la pile en respectant la polarité (+/-). Contrôler lors de la fermeture que le joint torique est correctement installé.
Lorsque la batterie est faible, il est possible que les mesures soient faussées. Une fois que le symbole de la batterie s'enclenche, il faut impérativement la changer.
4 COMMANDE / AFFICHAGE
Afchage :
COMM : Apparaît lorsque l’appareil est relié à un ordinateur MIN/MAX/AVG : Valeur minimale, maximale ou moyenne des données enregistrées
(fonctionne uniquement en mode LOG)
FULL : Apparaît lorsque la mémoire est pleine LOG : Apparaît lorsque la fonction d’enregistrement est activée : Apparaît lorsque la pile est faible °C/°F : Température %RH : Humidité relative (BL-1D, HL-1D) hPa : Pression (BL-1D) DP °C/°F : Point de rosée (BL-1D) Hi, Lo : Apparaît lorsque la température ou l’humidité dépasse ou est
en dessous du seuil d’alarme supérieur ou inférieur
4.3 LED D’AFFICHAGE DE L’ÉTAT
En mode LOG, la LED de droite clignote toutes les 5 secondes. La LED cli­gnote toutes les 5 secondes en rouge en cas de dépassement des seuils d’alarme inférieurs et supérieurs ou lorsque la pile est faible.
5 PARAMÈTRES / AFFICHAGE DES DONNÉES ENREGISTRÉES
Le paramétrage et le téléchargement ou l’afchage des données enregistrées nécessitent un PC
sur lequel le logiciel Rotronic HW4 est installé. La liaison entre l’appareil et le PC est effectuée avec un câble courant USB vers Mini-USB (AC0003). Le couvercle du raccordement USB sur l’appareil peut être ouver t avec une pièce de monnaie. Des informations plus précises pour le paramétrag e d’HW4 peuvent être tr ouvées dans le document d’aide du gestionnaire d’appareils.
Le temps doit être sy nchronisé lors de la première utilisation du logger.
6 RÉSOLUTION DES PROBLÈMES
Erreur Problème Solution
E02 La température est trop basse Température tolérée de l’environnement :
-30...70 °C
E03 La température est trop haute Température tolérée de l’environnement :
-30...70 °C
E31 Le capteur de température est
Faire réparer l’appareil
endommagé
E04 Erreur de mesure de la température Placer l’appareil de mesure dans un
environnement normal E11 Erreur d’étalonnage R H Répéter l’étalonnage de l’humidité E33 Circuit endommagé Faire réparer l’appareil
60
Raccordement mini USB (Paramètres et téléchargement des données)
Compartiment des piles (BAT.)
Intervalle d’enregistrement Capacité maximale de stockage at teinte après
30 sec 11 jours 2 h 5 min 111 j ours 30 min 1 an 301 jours 45 min 2 ans 270 jours 60 min >3 ans
Voir aussi la durée de vie de la pile. Seuil de batterie faible 2,6 V.
4.1 TOUCHE START/STOP
Presser brièvement cette touche pour mettre l’appareil en/hors service (l’appareil ne peut pas être mis hors service en mode d’enregistrement). Pour démarrer ou ar rêter un enregistrement, presser l a touche START/STOP
jusqu’à ce que « LOG » apparaisse sur l’afchage, ou programmer le temps
d’enregistrement désiré avec le logiciel HW4.
4.2 TOUCHE MODE
L’afchage alterne entre « Humidité et température» et « Pression et point
de rosée» toutes les 5 secondes (valeur standard) ou après une brève pres­sion de la touche MODE. Une longue pression en mode LOG afche les va­leurs MIN/MA X/AVG des données enregistrées.
HL-1D/TL-1D: En mode LOG brève pression de la touche, pour afcher les valeurs
MIN/MA X/AVG des données enregistrées
BL-1D:
Humidity &
Temperature
Press or
Time interval
Pressure &
Dew Point
Press > 2s
Press
Time interval Time interval Time interval
PressPress
Press
Press
Press
7 CARACTÉRISTIQUES TECHNIQUES
Précision 23 °C ±5 °C ±3.0 %rF, ±0.3 °C, ±3 hPa Intervalle d’enregistrement 30 s…24h Capacité mémoire 64'000 lig nes Fonctions MIN / MA X / AVG Afchage LCD, 2 lignes Fréquence de rafraîchisse-
ment de l’écran
5 sec. (standard) ( identique à l’intervalle d’enregistrement en mode enregistrement)
Afchage LED 2 LED, LED droite clignote en ver t pendant l’enregistrement
des données LED gauche clignote en rouge lors du dépasse-
ment des valeurs seuils ou si la pile est déchargée Communication Raccordement mini USB Logiciel HW4 V3.4.1 ou plus (BL-1D: V3.9 ou plus) inclus Gamme d’utilisation -30…7 0 °C
0…100 %RH (sans condensation) Pile 1 x CR2 Autonomie de la batterie 1 an
(intervalle d’enregistrement 1 h, température ambiante)
AVG 1MAX 1MIN 1
Type de protection IP IP67 Poids 85 g Dimensions 90 x 60 x 23 mm Compatible FDA-/GMP Logiciel HW4 conforme à FDA 21 CFR partie 11 / GAMP 5
AVG 2MAX 2MIN 2
Normes EN 1283 0 Accessoires Câble Mini USB AC0003 (inclus dans xL-1D-SET )
www.rotronic.comItaliano
12.8000.2201I
HL-1D / BL-1D / TL-1D
23
90
Manuale d'istruzioni breve
Data logger di umidità, temperatura, pressione e punto di rugiada (a partire dalla versione dello strumento V4.0)
1 DESCRIZIONE GENERALE
Ci congrat uliamo per l'acquisto di un nuovo data logger BL-1D (umidità, temperatura, pressio ­ne e punto di rugiada), HL-1D (umidità e temperatura), TL-1D (temperatura) Rotronic. Prima di
mettere in funzione lo strumento, si prega di leggere il presente manuale d'istruzioni breve. Il presente manuale d'istruzioni breve si limita a descrivere le funzioni principali dello stru­mento e la sua installazione.
HL-1D BL-1D TL-1D
Umidità x x Temperatura x x x Pressione x Punto di rugiada x Capacità di memoria (righe) 32,000 64,000
2 DIMENSIONI / CONNESSIONI
Modello HL-1D Modello BL-1D Modello TL-1D
60
Mini connessione USB
(impostazioni e download dati)
Vano batteria (B AT.)
Intervallo log Capacità di memoria raggiunta in
30 sec. 11 giorni 2 ore 5 min 111 g ior ni 30 min 1 anno 301 giorni 45 min 2 anni 270 giorni 60 min >3 anni
Vedere anche la durata della bat teria. Soglia batteria bassa 2,6 V.
3 INSERIMENTO O SOSTITUZIONE DELLA BATTERIA
I data logger funzionano con una batteria CR2. Aprire il coperchio BAT e inserire la batteria rispettando la cor retta po larità (+/-). Alla chiu sura prestare attenzione al corretto ins erimento dell'O-ring di guarnizione.
Quando la batteria è scarica i valori misurati potrebbero non essere corretti. La bat­teria deve essere sostituita ogni qualvolta compare il relativo simbolo.
4 COMANDI / DISPLAY
Display:
COMM: compare se lo strumento è collegato ad un computer MIN/MAX/AVG: valore minimo, massimo o medio dei dati salvati
(funziona solo in modalità LOG)
FULL: compare se la memoria è piena LOG: compare se la funzione di registrazione è attiva : compare se la batteria è prossima all'esaurimento °C/°F: temperatura %UR: umidità relativa (BL-1D, HL-1D) hPa: pressione (BL-1D) DP °C/°F: punto di rugiada (BL-1D) Hi, Lo: compare se il valore di temperatura o di umidità è superiore o inferiore
alla soglia di livello massimo o di livello minimo
4.1 TASTO START/STOP
Premere brevemente il ta sto per accendere o spegnere lo str umento (in mo­dalità LOG lo strumento non si può spegnere). Per avviare o interrompere
una registrazione dei dati, premere il tasto START/STOP nché sul display si visualizza "LOG" o programmare il tempo di registrazione desiderato me-
diante HW4.
4.2 TASTO MODE
Ogni 5 secondi (valore standard) o un breve azionamento del tasto MODE si alterna la visualizzazione di "Umidità e temperatura" e "Pressione e punto di rugiada". Premere a lungo in modalità LOG, per visualizzare MIN/MAX/
AVG dei dati salvati.
HL-1D / TL-1D: premere brevemente il tasto in modalità LOG, per visualizzare
MIN/MA X/AVG dei dati salvati
BL-1D:
Humidity &
Temperature
Press or
Time interval
Pressure &
Dew Point
Press > 2s
Press
Time interval Time interval Time interval
PressPress
Press
Press
Press
AVG 1MAX 1MIN 1
AVG 2MAX 2MIN 2
4.3 LED PER L'INDICAZIONE DI STATO
In modalità Log il LED a destra presenta ogni 5 secondi una luce lampeg­giante verde. Se si supera o si resta al di sotto della soglia di allarme e in caso di batteria prossima all'esaurimento, il LED a sinistra presenta ogni 5 secondi una luce lampeg giante rossa.
5 IMPOSTAZIONI / VISUALIZZAZIONI DEI DATI REGISTRATI
Le impostazioni e il download o la visualizzazione dei dati registrati richiedono un PC, nel quale sia installato il software HW4 Rotronic. Il collegamento fra strumento e PC si realizza con una
porta US B normalmente disponibile in commercio e un mini-cavo USB ( AC0003). Il coperchio del
connettore USB sullo strumento si può aprire con una moneta. Informazioni più dettagliate sulle impostazioni mediante HW4 si trovano nel documento di supporto al dispositivo di controllo.
Quando si usa il logger la prima volta, l'orario va sincronizzato.
6 GESTIONE PROBLEMI
Errore Problema Soluzione
E02 La temperatura è troppo bassa Temperatura ambiente consentita: -30...70 °C E03 La temperatura è troppo alta Temperatura ambiente consentita: -30...70 °C E31 Sensore di temperatura
danneggiato
E04 Errore nella misura di
temperatura
Lo strumento deve essere inviato al repar to
Riparazioni
Collocare lo strumento di misura in un ambiente normale
E11 Errore di calibrazione UR Ripetere la calibrazione di umidità E33 Circuito danneggiato Lo strumento deve essere inviato al repar to
Riparazioni
7 DATI TECNICI
Precisione 23 °C ±5 °C ±3.0 %UR, ±0.3 °C , ±3 hPa Intervallo log 30 s…24h Capacità di memoria 64.000 righe Funzione MIN / M AX / AVG Display LCD a 2 righe Fréquence de rafraîchisse-
ment de l’écran
5 sec. (standard)
(in modalità registrazione uguale all'intervallo log)
Indicatore LED 2 LED, il LED a destra ha una luce lampeggiante verde
durante la registrazione dei dati
Il LED a sinistra ha una luce lampeggiante rossa in caso
di valori limite o di batteria prossima all'esaurimento Comunicazione Mini connessione USB Software HW4 V3.4.1 o superiore (BL-1D: V3.9 o superiore) compreso Campo di lavoro -30… 70 °C
0…100 %UR (non condensante) Batteria 1 x CR2 Durata batteria 1 anno (1 h di intervallo log, temperatura ambiente) Classe di protezione IP IP67 Peso 85 g Dimensioni 90 x 60 x 23 mm Compatibile FDA-/GMP Soft ware HW4 conforme a FDA 21 CFR Part 11 / GAMP 5 Norme EN 12830 Accessori Cavo mini USB AC0003 (contenuto nel SE T xL-1D)
Loading...