Roland LX-15e Owner's Manual

Download

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING - When using electric products, basic precautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

For the U.K.

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE: BROWN:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS”, “USING THE UNIT SAFELY” (p.

3), and “IMPORTANT NOTES” (p. 5). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

NEUTRAL LIVE



USING THE UNIT SAFELY

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

About WARNING and CAUTION Notices

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or

other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

WARNING

Do not disassemble or modify by yourself

Do not open or perform any internal modications on the unit.

Do not repair or replace parts by yourself

Do not attempt to repair the unit, or replace parts within it (except when this manual provides specic instructions directing you to do so). Refer all servicing to your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.

Do not use or store in the following types of locations

• Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heatgenerating equipment); or are

• Damp (e.g., baths, washrooms, on wet oors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Humid; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and shakiness.

Do not place in an unstable location

Make sure you always have the unit placed so it is level and sure to remain stable. Never place it on stands that could wobble, or on inclined surfaces.

Connect the power cord to an outlet of the correct voltage

The unit should be connected to a power supply only of the type described as marked on the rear panel of unit.

Use only the included power cord

Use only the attached power-supply cord. Also, the included power cord must not be used with any other device.

Do not bend the power cord or place heavy objects on it

Do not excessively twist or bend the power cord, nor place heavy objects on it. Doing so can damage the cord, producing severed elements and short circuits. Damaged cords are re and shock hazards!

About the Symbols

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power-cord plug must be unplugged from the outlet.

ALWAYS OBSERVE THE FOLLOWING

WARNING

Avoid extended use at high volume

This unit, either alone or in combination with an amplier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level, or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should immediately stop using the unit, and consult an audiologist.

Don’t allow foreign objects or liquids to enter unit; never place containers with liquid on unit

Do not place containers containing liquid on this product. Never allow foreign objects (e.g., ammable objects, coins, wires) or liquids (e.g., water or juice) to enter this product. Doing so may cause short circuits, faulty operation, or other malfunctions.

Turn o the unit if an abnormality or malfunction occurs

Immediately turn the unit o, remove the power cord from the outlet, and request servicing by your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page when:

• The power-supply cord or the plug has been damaged; or

• If smoke or unusual odor occurs; or

• Objects have fallen into, or liquid has been spilled onto the unit; or

• The unit has been exposed to rain (or otherwise has become wet); or

• The unit does not appear to operate normally or exhibits a marked change in performance.

Adults must provide supervision in places where children are present

When using the unit in locations where children are present, be careful so no mishandling of the unit can take place. An adult should always be on hand to provide supervision and guidance.

Do not drop or subject to strong impact

Protect the unit from strong impact. (Do not drop it!)

WARNING

Do not share an outlet with an unreasonable number of other devices

Do not force the unit’s power-supply cord to share an outlet with an unreasonable number of other devices. Be especially careful when using extension cords—the total power used by all devices you have connected to the extension cord’s outlet must never exceed the power rating (watts/ amperes) for the extension cord. Excessive loads can cause the insulation on the cord to heat up and eventually melt through.

Do not use overseas

Before using the unit in a foreign country, consult with your retailer, the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.

Convenient Functions

Function Mode

Appendix

USING THE UNIT SAFELY

CAUTION

Place in a well ventilated location

The unit should be located so that its location or position does not interfere with its proper ventilation.

Grasp the plug when connecting or disconnecting the power cord

Always grasp only the plug on the power-supply cord when plugging into, or unplugging from, an outlet or this unit.

Periodically clean the power cord’s plug

At regular intervals, you should unplug the power plug and clean it by using a dry cloth to wipe all dust and other accumulations away from its prongs. Also, disconnect the power plug from the power outlet whenever the unit is to remain unused for an extended period of time. Any accumulation of dust between the power plug and the power outlet can result in poor insulation and lead to re.

Manage cables for safety

Try to prevent cords and cables from becoming entangled. Also, all cords and cables should be placed so they are out of the reach of children.

Avoid climbing on top of the unit, or placing heavy objects on it

Never climb on top of, nor place heavy objects on the unit.

Do not connect or disconnect the power cord with wet hands

Never handle the power cord or its plugs with wet hands when plugging into, or unplugging from, an outlet or this unit.

Cautions when moving this unit

If you need to move the instrument, take note of the precautions listed below. At least two persons are required to safely lift and move the unit. It should be handled carefully, all the while keeping it level. Make sure to have a rm grip, to protect yourself from injury and the instrument from damage.

• Check to make sure the screws securing the unit to the stand have not become loose. Fasten them again securely whenever you notice any loosening.

• Disconnect the power cord.

• Disconnect all cords coming from external devices.

• Raise the adjusters on the stand (p. 63).

• Close the lid and the top lid.

CAUTION

If there is a possibility of lightning strike, disconnect the power cord from the outlet

Whenever you suspect the possibility of lightning in your area, pull the plug on the power cord out of the outlet.

Take care so as not to get ngers pinched by lid

Be careful when opening/closing the lid so you do not get your ngers pinched (p. 16). Adult supervision is recommended whenever small children use the unit.

Precautions concerning use of bench

When using the stool, please observe the following points:

• Do not use the stool as a toy, or as a stepping stool.

• Do not allow two or more persons to sit on the stool.

• Do not adjust the height while sitting on the stool.

• Do not sit on the stool if the bolts holding the stool legs are loose. (If the bolts are loose, immediately re-tighten them using the supplied tool.)

• Never insert your hand into the gap (the metal height adjustment mechanism) under the seat lid. Doing so may cause your hand to be pinched or injured.

Keep small items out of the reach of children

To prevent accidental ingestion of the parts listed below, always keep them out of the reach of small children.

• Removable Parts Screws for stand assembly (p. 63)

Take care not to get burned

Around the display may become hot, so take care to avoid burns.

Unplug the power cord from the outlet before cleaning

Before cleaning the unit, turn it o and unplug the power cord from the outlet (p. 62).



IMPORTANT NOTES

Power Supply

• Do not connect this unit to same electrical outlet that is being used by an electrical appliance that is controlled by an inverter or a motor (such as a refrigerator, washing machine, microwave oven, or air conditioner). Depending on the way in which the electrical appliance is used, power supply noise may cause this unit to malfunction or may produce audible noise. If it is not practical to use a separate electrical outlet, connect a power supply noise lter between this unit and the electrical outlet.

• To prevent malfunction and equipment failure, always make sure to turn o the power on all your equipment before you make any connections.

• Although the LCD and LEDs are switched o when the unit is turned o, this does not mean that the unit has been completely disconnected from the source of power. If you need to turn o the power completely, rst turn o the unit’s switch, then unplug the power cord from the power outlet. For this reason, the outlet into which you choose to connect the power cord’s plug should be one that is within easy reach and readily accessible.

• With the factory settings, the LX-15e will automatically

be switched o 30 minutes after you stop playing or operating the unit. If you don’t want the unit to turn o automatically, change the “AUTO OFF” setting to “OFF” as described on p. 44.

NOTE

The settings you were editing will be lost when the unit is turned o. If you want to keep your settings, you must save your settings before turning the unit o.

Placement

• Using the unit near power ampliers (or other

equipment containing large power transformers) may induce hum. To alleviate the problem, change the orientation of this unit; or move it farther away from the source of interference.

• This device may interfere with radio and television

reception. Do not use this device in the vicinity of such receivers.

• Noise may be produced if wireless communications

devices, such as cell phones, are operated in the vicinity of this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them o.

• Do not expose the unit to direct sunlight, place

it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. Also, do not allow lighting devices that normally are used while their light source is very close to the unit (such as a piano light), or powerful spotlights to shine upon the same area of the unit for extended periods of time. Excessive heat can deform or discolor the unit.

• When moved from one location to another where

the temperature and/or humidity is very dierent, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated.

• Do not allow rubber, vinyl, or similar materials to

remain on this unit for long periods of time. Such objects can discolor or otherwise harmfully aect the nish.

• Do not allow objects to remain on top of the

keyboard. This can be the cause of malfunction, such as keys ceasing to produce sound.

• Do not paste stickers, decals, or the like to this instrument. Peeling such matter o the instrument may damage the exterior nish.

• Do not put anything that contains water on this unit. Also, avoid the use of insecticides, perfumes, alcohol, nail polish, spray cans, etc., near the unit. Swiftly wipe away any liquid that spills on the unit using a dry, soft cloth.

Maintenance

• To clean the unit, use a dry, soft cloth; or one that is slightly dampened. Try to wipe the entire surface using an equal amount of strength, moving the cloth along with the grain of the wood. Rubbing too hard in the same area can damage the nish.

• Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation.

• The pedals of this unit are made of brass. Brass eventually darkens as the result of the natural oxidization process. If the brass becomes tarnished, polish it using commercially available metal polisher.

Maintenance (Polished-nish pianos)

• Since your piano has a polished nish that is as delicate as that found on nely crafted wooden furniture, it needs careful, periodic care. A few important suggestions concerning the proper care of the unit follow. For dusting, using a soft, clean cloth and/or piano-use feather duster. Be sure to wipe gently. Even the tiniest grains of sand or grit can leave scratches on the surface if too much force is applied while wiping. Do not use any cleaners or detergents, since they might deteriorate the surface of the cabinet, and produce cracks.

If the cabinet’s surface loses its luster, wipe it thoroughly with a soft cloth dampened with a little of the polishing liquid. Do not use any cleaners or detergents, since they might deteriorate the surface of the cabinet, and produce cracks. Do not use dusting cloths that contain chemicals.

• About piano polishing liquid

• Use polishing liquid as directed by the instructions

for the product.

• Use only polishing liquid that is intended for use on

polished-nish pianos. Using any other polishing liquid may cause scratches, deformation, or discoloration. To purchase polishing liquid, contact your nearby musical instrument dealer.

• Use the polishing liquid only on the polished

surfaces of the cabinet. Always wipe the surface with the grain using straight, even strokes. Do not repeatedly wipe the same places using too much pressure, since that might result in the loss of luster.

• Be sure to keep the polishing liquid out of the

reach of small children. If the polishing liquid is accidentally swallowed, rst get them to vomit, then take them to a doctor.

Repairs and Data

• Please be aware that all data contained in the unit’s memory may be lost when the unit is sent for repairs. Important data should always be backed up USB ash drives, or written down on paper (when possible). During repairs, due care is taken to avoid the loss of data. However, in certain cases (such as when circuitry related to memory itself is out of order), we regret that it may not be possible to restore the data, and Roland assumes no liability concerning such loss of data.

Additional Precautions

• Please be aware that the contents of memory can be irretrievably lost as a result of a malfunction, or the improper operation of the unit. To protect yourself against the risk of loosing important data, we recommend that you periodically save a backup copy of important data you have stored in the unit’s memory on a USB ash drive.

• Unfortunately, it may be impossible to restore the contents of data that was stored in the unit’s memory, USB ash drive once it has been lost. Roland Corporation assumes no liability concerning such loss of data.

• Use a reasonable amount of care when using the unit’s buttons, sliders, or other controls; and when using its jacks and connectors. Rough handling can lead to malfunctions.

• Never strike or apply strong pressure to the display.

• When disconnecting all cables, grasp the connector itself—never pull on the cable. This way you will avoid causing shorts, or damage to the cable’s internal elements.

• A small amount of heat will radiate from the unit during normal operation.

• To avoid disturbing others nearby, try to keep the unit’s volume at reasonable levels. You may prefer to use headphones, so you do not need to be concerned about those around you.

• The sound of keys being struck and vibrations produced by playing an instrument can be transmitted through a oor or wall to an unexpected extent. Please take care not to cause annoyance to others nearby.

• When you need to transport the unit, pack it in shock-absorbent material. Transporting the unit without doing so can cause it to become scratched or damaged, and could lead to malfunction.

• Do not apply undue force to the music stand while it is in use.

• Some connection cables contain resistors. Do not use cables that incorporate resistors for connecting to this unit. The use of such cables can cause the sound level to be extremely low, or impossible to hear. For information on cable specications, contact the manufacturer of the cable.

• Before opening or closing the keyboard lid, always make sure that no pets or other small animals are located on top of the instrument (in particular, they should be kept away from the keyboard and its lid). Otherwise, due to the structural design of this instrument, small pets or other animals could end up getting trapped inside it. If such a situation is encountered, you must immediately turn o the unit and disconnect the power cord from the outlet. You should then consult with the retailer from whom the instrument was purchased, or contact the nearest Roland Service Center.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Function Mode

Appendix

IMPORTANT NOTES

Before Using USB Memories

(Using Optional USB ash drive)

• Do not connect or disconnect USB ash drive while it is being read from, or written to (i.e., while the USB ash drive access indicator will blink).

• Carefully insert the USB ash drives all the way in— until it is rmly in place.

• Never touch the terminals of the USB ash drives. Also, avoid getting the terminals dirty.

• USB ash drives are constructed using precision components; handle the USB ash drives carefully, paying particular note to the following.

• To prevent damage to the USB ash drives from static electricity, be sure to discharge any static electricity from your own body before handling the USB ash drives.

• Do not touch or allow metal to come into contact with the contact portion of the USB ash drives.

• Do not bend, drop, or subject USB ash drives to strong shock or vibration.

• Do not keep USB ash drives in direct sunlight, in closed vehicles, or other such locations.

• Do not allow USB ash drives to become wet.

• Do not disassemble or modify the USB ash drives.

Copyrights / Licenses / Trademarks

• It is forbidden by law to make an audio recording, video recording, copy or revision of a third party’s copyrighted work (musical work, video work, broadcast, live performance, or other work), whether in whole or in part, and distribute, sell, lease, perform, or broadcast it without the permission of the copyright owner.

• Do not use this product for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this product.

• The copyright of content in this product (the sound waveform data, style data, accompaniment patterns, phrase data, audio loops and image data) is reserved by Roland Corporation.

• Purchasers of this product are permitted to utilize said content (except song data such as Demo Songs) for the creating, performing, recording and distributing original musical works.

• Purchasers of this product are NOT permitted to extract said content in original or modied form, for the purpose of distributing recorded medium of said content or making them available on a computer network.

• MMP (Moore Microprocessor Portfolio) refers to a patent portfolio concerned with microprocessor architecture, which was developed by Technology Properties Limited (TPL). Roland has licensed this technology from the TPL Group.

• XGlite ( of Yamaha Corporation.

• Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.

) is a registered trademark or a trademark

• Company names and product names appearing in this document are registered trademarks or trademarks of their respective owners.

• Microsoft, Windows, Windows Vista, and DirectX are either registered trademarks or trademarks of Microsoft Corporation.

• Mac OS and iTunes are either registered trademarks or trademarks of Apple Inc.

• Roland, GS, and SuperNATURAL are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.



About the Ivory Feel Keyboard

Features of an ivory feel keyboard

Traditional piano keys are made from the best materials-ivory (for white keys) and ebony (for black keys). The Ivory Feel keyboard uses the latest in technology to reproduce the touch and feel of these materials.

An Ivory Feel keyboard oers the following features.

• We’re sure you’ll develop a fondness for the distinctive texture of these keys, which feels better the more you play them.

• Surfaces incorporate stripes of moisture-absorbing material for improved touch and playability.

• The keys feature subtle gloss and understated coloring, enhancing the look and elegance.

• The white keys are nished with a slight yellowish tinge for the look of real ivory.

Handling

• Do not write on the keyboard with any pen or other implement, and do not stamp or place any marking on the instrument. Ink will seep into the surface lines and become unremovable.

• Do not ax stickers on the keyboard. You may be unable to remove stickers that use strong adhesives, and the adhesive may cause discoloration.

Care and maintenance

Please note the following points. Failure to do so may result in scratches on the surface nish, damaged gloss, or other discoloration or deformation.

• To remove dirt, use a soft cloth. Using a moistened and tightly wrung-out cloth, gently wipe o any dirt. Do not rub the surface vigorously.

• To remove stubborn dirt, use a commercially available keyboard cleaner that does not contain abrasives. Start by wiping lightly. If the dirt does not come o, wipe using gradually increasing amounts of pressure while taking care not to scratch the keys.

• Do not use benzene, paint thinner, or alcohol on the instrument.



Contents

USING THE UNIT SAFELY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

About the Ivory Feel Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Look What You Can Do! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Operation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Panel Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Before You Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Opening/Closing the Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Opening/Closing the Top Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Turning the Power On/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Performing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Performing with Various Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Switching Tones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Performing with Two Layered Tones (Dual Play) . . . . . . . . . . . . . . . . . . . . . . . . . . .19

Playing Dierent Tones with the Right and Left Hands (Split Play) . . . . . . . . .20

Adjusting the Sound to Your Taste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Adding Reverberation to the Sound (Ambience) . . . . . . . . . . . . . . . . . . . . . . . . . .22

Adjusting the Brightness of the Sound (Brilliance) . . . . . . . . . . . . . . . . . . . . . . . .23

Adjusting the Keyboard Response (Key Touch) . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Dividing the Keyboard for Two-Person Performance (Twin Piano) . . . . . .24

Shifting the Pitch (Transpose) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Practicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Practicing with the Metronome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Changing the Tempo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Changing the Time Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Adjusting the Metronome’s Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Adding a Count-in to Synchronize Your Performance . . . . . . . . . . . . . . . . . . . . .27

Practicing with a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Selecting and Playing a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Playing Songs Consecutively (All Songs Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Adjusting the Volume Balance of the Song and the Keyboard

Performance (Song Balance) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting a Song’s Tempo for Easier Practicing. . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Practicing One Hand at a Time (Part Mute). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Repeatedly Practicing a Portion of a Song (AB Repeat) . . . . . . . . . . . . . . . . . . . .31

Recording the Song You’re Practicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

SMF Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32

Overdubbing a Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

Converting a Song Recorded as an SMF to Audio . . . . . . . . . . . . . . . . . . . . . . . . .37

Audio Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Transposing a Song for Easier Performance (Audio Transpose) . . . . . . . . . . . .39

Enjoying Karaoke with an Audio File (Center Cancel) . . . . . . . . . . . . . . . . . . . . . .39

Burning an Audio Recording of a Song (WAV le) to a CD . . . . . . . . . . . . . . . . .40

Renaming a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Personalizing Your Piano Sound (Piano Designer) . . . . . . . . . . . . . . . . . . 42

Making Detailed Adjustments to the Piano Sound . . . . . . . . . . . . . . . . . . . . .42

Convenient Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Adjusting the Brightness of the Display (Display Contrast) . . . . . . . . . . . . .44

Making the Power Automatically Turn O After a Time (Auto O) . . . . . .44

Retaining the Settings Even After Power-o (Memory Backup) . . . . . . . . .44

Restoring the Factory Settings (Factory Reset) . . . . . . . . . . . . . . . . . . . . . . . . .44

Copying a Saved Song (Copy Song) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Deleting a Saved Song (Delete Song) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Initializing the Memory (Format Media) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Disabling the Buttons (Panel Lock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Loading/Saving Piano Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Loading a Piano Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Saving a Piano Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

About the Wireless LAN Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Basic Connection Method (Connect by WPS) . . . . . . . . . . . . . . . . . . . . . . . . . .48

Wireless LAN Function Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Status Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

Connecting to a Wireless LAN Access Point That You Select (Select AP) . . . .49

Other Settings (Option) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Various Settings (Function Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Applying a Headphones 3D Ambience Eect to the Piano Sound

(Headphones 3D Ambience) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Adjusting the Dual Play Volume Balance (Dual Balance) . . . . . . . . . . . . . . . . . . .51

Matching the Pitch with Other Instruments (Master Tuning) . . . . . . . . . . . . . .51

Changing the Tuning Method (Temperament) . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Specifying a Song’s Tonic (Temperament Key) . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Adjusting the Volume of an Audio Playback Device (Input Volume) . . . . . . . .51

Playing Back an Audio File with Its Central Sound Minimized (Center

Cancel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Transposing an Audio File (Audio Transpose) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

Specifying What the Transpose will Aect (Transpose Mode) . . . . . . . . . . . . . .52

Changing the Pitch of the Tone in Octave Steps (Octave Shift) . . . . . . . . . . . . .52

Selecting the Format for Recording (Recording Mode) . . . . . . . . . . . . . . . . . . . .52

Changing How the Pedal Eects Are Applied (Damper Pedal Part) . . . . . . . . .52

Changing How the Pedals Work (Center Pedal) . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Preventing Doubled Notes When Connected to a Sequencer (Local

Control) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MIDI Transmit Channel Settings (MIDI Transmit Channel) . . . . . . . . . . . . . . . . . .52

Renaming a Song (Save Song) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

Copying a Saved Song (Copy Song) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Deleting a Saved Song (Delete Song) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Initializing the Memory (Format Media) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Changing the USB Driver Settings (USB Driver) . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Changing the USB ash drive Setting (USB Memory Mode) . . . . . . . . . . . . . . .53

Controlling Video Equipment (Visual Control Mode) . . . . . . . . . . . . . . . . . . . . . .53

Specifying the Visual Control Channel (Visual Control Channel) . . . . . . . . . . .53

Wireless LAN Function Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Adjusting the Brightness of the Display (Display Contrast) . . . . . . . . . . . . . . . .53

Specifying the Maximum Volume (Volume Limit) . . . . . . . . . . . . . . . . . . . . . . . . .54

Making the Power Automatically Turn O After a Time (Auto O) . . . . . . . . .54

Loading/Saving Piano Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Storing Your Settings (Memory Backup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Restoring the Factory Settings (Factory Reset) . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Tone List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Internal Song List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Main Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

How to read the explanatory illustrations

Press two buttons.

Numerals indicate the sequence of steps.

Press one of the enclosed buttons.

Function Mode

Appendix

While holding down a button, press another button.



Look What You Can Do!



Play the Piano



Practice Songs



Sound a metronome

You can sound a metronome.



Play various sounds

The LX-15e contains a wide variety of tones (sounds). You can freely select and perform using these tones.



Play two layered tones

You can layer two tones on a single key.



Play dierent tones with your left and right hands

You can divide the keyboard into left and right zones, and select a dierent tone for each zone.



Play duets

You can divide the keyboard into left and right halves, playing it as though it were two pianos.

page 26

page 18

page 19

page 20

page 24



Practice along with the built-in songs

The LX-15e contains numerous built-in songs. For the song titles, refer to “Internal Song List” (p. 59).



Practice each hand separately

You can practice along with a song while listening to only the right-hand or left-hand part play back.



Record Songs



Record your performances

You can record your own playing.



Use your computer to create a CD of a song you recorded

A song you’ve recorded can be copied to your computer, and written to a CD.

page 28

page 30

page 32

page 40



Environmentally Friendly Energy-Ecient Design



The power will turn o after a specied time has elapsed

When thirty minutes have elapsed since you last played or operated the LX-15e, the power will turn o automatically.

* If you don’t want the power to turn o automatically, change the “Auto O” setting (p. 44).

page 44



Adjust Your Piano

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer



Adjust the keyboard touch

You can adjust the touch sensitivity of the keyboard to match your own playing style.



Add reverberation to the sound

You can add reverberation (ambience) to create the sensation of performing in a concert hall.



Adjust the brightness of the sound

You can adjust the tone quality of the sound, ranging from a brilliant timbre to a mellow tone.



Personalize Your Piano (Piano Designer)



Adjust the openness of the grand piano’s lid

Closing the lid will produce a softer tone, and opening it will produce a brighter tone.

page 23

page 22

page 23

page 42



Adjust the resonance of chords

You can modify the resonance of chords by changing the way in which the piano’s soundboard vibrates.



Switch the temperament

You can switch between various temperaments, such as historic temperaments used during the Baroque era.



Convenient Functions



Transpose the pitch of the keyboard or song

The Transpose function lets you shift the pitch of the keyboard or a song so that you can perform more conveniently.



Disable the buttons

page 43

Convenient Functions

page 25

Function Mode

page 46

The Panel Lock function lets you prevent sounds or settings from being changed when buttons are pressed inadvertently.



Connect to a Wireless LAN

You can use a WNA1100-RL wireless USB adapter (sold separately) to connect to a wireless LAN and use wireless applications, such as the iPad app.

page 48

Appendix



Operation Guide

Describing this area

Adding Reverberation (Ambience)

You can add a pleasant reverberation to the sounds, producing the impression that you are performing in a concert hall.

To turn ambience on

Press the [Ambience] button so it’s lit.

To adjust the ambience

While holding down the [Ambience] button, press the [–] [+] buttons.

Adjusting the Overall Volume

Adjust the sound’s volume.

page 17

MaxMin

page 22

Adjusting the Brightness of the Sound (Brilliance)

You can adjust the brightness of the sound you play

from the keyboard or the sounds of a song you play back.

To turn brilliance on

Press the [Brilliance] button so it’s lit.

To adjust the brilliance

While holding down the [Brilliance] button, press the [–] [+] buttons.

page 23

Adjusting the Song Volume

(Song Balance)

By modifying the playback volume of the song, you can adjust the balance between the song and your keyboard performance.

To turn song balance on

Press the [Song Balance] button so it’s lit.

To adjust the song balance

While holding down the [Song Balance] button, press the [–] [+] buttons.

page 29

Adjusting the Keyboard Touch

(Key Touch)

You can adjust the way in which the keyboard responds to your playing.

To turn key touch on

Press the [Key Touch] button so it’s lit.

To adjust the key touch

While holding down the [Key Touch] button, press the [–] [+] buttons.

page 23

Transposing Your Performance

Transposes the keyboard and/or song.

To turn transpose on

Press the [Transpose] button so it’s lit.

To adjust the amount of transposition

While holding down the [Transpose] button, press the [–] [+] buttons.

Retaining the settings even after power-o (memory backup)

The LX-15e allows you to adjust numerous settings, but these settings will return to their default values as soon as you turn o the power.

However, by using the Memory Backup feature, you can have the changes you’ve made in settings be retained.

1. While holding down the [Key Touch]

button, press the [Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select

“Memory Backup.”

3. Press the [Song] button.

4. Use the [+] button to select “OK.”

5. Press the [Song] button.

(Transpose)

page 25

page 44

Switching Tones

Operation Guide

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

To select a single tone

Press one of the tone buttons, and then use the [–] [+] buttons.

Press one

page 18

Dividing the Keyboard for Two-person Performance (Twin Piano)

This function divides the keyboard into left and right, allowing two people to play the same range of pitches.

To turn twin piano on

Press the [Twin Piano] button so it’s lit.

page 24

To layer two tones (dual play)

Press two tone buttons.

Press two

page 19

To change the tones

Tone 1 Press the [–] [+] buttons.

Tone 2

Hold down the right-most of the lit tone button, and then use the [–] [+] buttons.

Playing Dierent Tones with the Right and Left Hands (Split Play)

This function divides the keyboard into left and right zones, allowing you to play a dierent tone in each zone.

To turn split on

While holding down the [Transpose] button, press the [Twin Piano] button.

page 20

To change how the sounds are heard

While holding down the [Twin Piano] button, press the [–] [+] buttons.

To change the tones

Right-hand Tone

Left-hand Tone

Pair

Individual

The sound of the right-hand keyboard zone will be heard more loudly from the right speaker than from the left speaker.

The sound of the left-hand keyboard zone will be heard more loudly from the left speaker than from the right speaker.

The sound of the right-hand keyboard zone will be heard only from the right speaker.

The sound of the left-hand keyboard zone will be heard only from the left speaker.

Changing the keyboard’s split point

While holding down the [Transpose] button and [Twin Piano] button, play the key that you want to specify as the split point.

Customizing Your Piano Sound (Piano Designer)

You can adjust various elements of a grand piano’s sound to create your own personalized piano.

1. While holding down the Piano [Grand] button, press the Piano [Upright] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select the item that you want to adjust.

3. Use the [–] [+] buttons to adjust the value.

1. Press a tone button.

2. Press the [–] [+] buttons.

1. While holding down the [Transpose] button and [Twin Piano] button, press a tone button.

2. While holding down the [Transpose] button and [Twin Piano] button, use the [–] [+] buttons.

page 42

Convenient Functions

Function Mode

Appendix

Operation Guide

Describing this area

Using the Metronome

Here’s how to sound the metronome.

To turn the metronome on

Press the [Metronome] button so it’s lit.

To adjust the metronome’s volume

While holding down the [Metronome] button, use the [–] [+] buttons.

page 26

Changing the Tempo or Time Signature

You can adjust the tempo of the metronome or song.

To change the tempo

Use the [ ] [ ] (Slow/Fast) buttons.

To change the time signature

While holding down the [Metronome] button, use the [ ] [ ] (Slow/Fast) buttons.

page 26

Display

The display shows information such as the tone name, song title, tempo, and time signature.

Tempo Time signature Measure Tone Name

Song Name

Selecting Variation Tones/Adjusting the Settings

You can select tone variations or songs, and adjust various settings.

• Holding down the [–] [+] buttons will make the value change continuously.

• To rapidly increase the value, hold down the [+] button and press the [–] button.

• To rapidly decrease the value, hold down the [–] button and press the [+] button.

• To return the value to its default setting, press the [–] and [+] buttons simultaneously.

Selecting a Song

First, you need to access the song screen; this is where you can select songs.

To select a song

page 28

1. Press the [Song] button to access the song screen.

Panel Descriptions

[Power] Switch

This turns the power on/o.

page 17

WARNING

* The power to this unit will be turned o automatically

after a predetermined amount of time has passed since it was last used for playing music, or its buttons or controls were operated (Auto O function).

If you do not want the power to be turned o automatically, disengage the Auto O function (p. 44).

* Any settings that you are in the process of editing will be lost when the

power is turned o. If you have any settings that you want to keep, you should refer to “Retaining the Settings Even After Power-o (Memory

Backup)” (p. 44) and save your settings. * To restore power, turn the power on again * When turning the power on again, you must allow at least ve seconds

after power-o before you once again turn the power on. If you fail to allow

enough time, the Auto O function might not be reset, preventing the

power from turning on correctly.

Top Lid

By opening or closing the lid you can change the clarity of the sound.

page 16

Headphone Hook

Whenever you are not using the headphones, you can hang them on the headphone hook.

Front Panel

These buttons and sliders are used to operate the LX-15e.

“Operation Guide” page 10–13

Pedals

Damper Pedal

Use this pedal to sustain the sound. While this pedal is held down, notes will be sustained for an extended time even if you release your ngers from the keyboard.

With the damper pedal on an acoustic piano, when you step on the pedal it will at rst oer only a slight amount of resistance, but as you press down further it will start to feel much heavier. On the LX-15e, this change in the feeling of resistance is simulated.

On an acoustic piano, when you step on the damper pedal, you’ll rst hear the sound of the dampers releasing the strings. Then, you should also be able to hear the sound of strings adjacent to the ones for the notes actually played resonate sympathetically, resulting in a rich, resounding tone.

Additionally, when using half-pedaling techniques, the core of the sound disappears rapidly while a rich, spacious resonance remains, producing a unique form of reverberation. On the LX-15e, the unique, lingering tones produced by the half-pedaling technique are reproduced in addition to released-string sounds (Damper Noise) and resonating sounds (Damper Resonance).

Sostenuto Pedal

The notes you are pressing when this pedal is depressed will be sustained.

* Don’t hang anything other than headphones on

this hook, and don’t apply excessive force to it. Doing so may damage the headphone hook.

Soft Pedal

This pedal is used to make the sound softer. Playing with the soft pedal depressed produces a sound that is not as strong as when otherwise played with the equivalent

strength. This is the same function as the left pedal of an acoustic piano. The softness of the tone can be varied subtly by the depth to which you press the pedal.

Panel Descriptions

USB Memory Port

If a USB ash drive is connected, you can use it to save or play back songs.

You can do the following things using a USB ash drive.

• WAVE les or MIDI les (SMF) data copied from your computer can be played back by the LX-15e.

• You can make audio recordings of your performances on the LX-15e.

• The audio recordings of songs that you’ve made can be played on your computer, or burned to a CD.

* Carefully insert the USB ash drives all the way in-until it is rmly

in place.

* Use a USB ash drive sold by Roland. We cannot guarantee

operation if any other USB ash drive is used.

Pedal Connector

Connect the pedal cord of the dedicated stand to this connector.

page 63

page 28 page 41

AC In (AC Inlet)

Connect the included power cord here.

page 63

Rear side

USB Computer Port

If you use a commercially available USB cable to connect the LX-15e to your computer, you’ll be able to do the following things.

• SMF data played back by MIDI-compatible software can be sounded by the LX-15e.

• MIDI data can be transferred between the LX-15e and your sequencer software, opening up a wide range of possibilities for music production and editing.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Output Jacks

If you connect these jacks to amplied speakers, the sound of LX-15e will be heard through them.

* Before turning o the power of

the LX-15e, you must rst turn o the power of the devices that are connected to the Output jacks.

Phones Jacks

Here you can connect headphones. The LX-15e has two headphone jacks, two people

can also use headphones simultaneously.

A Headphones 3D Ambience eect will be applied, producing the sensation that the sound is emanating from the piano itself even when using headphones.

* The Headphones 3D Ambience eect applies only to piano tones; it

does not apply to other tones. * You can also turn the Headphones 3D Ambience eect o (p. 51). * You can use the [Ambience] button to adjust the Headphones 3D

Ambience eect.

Input Jack

If a digital audio player or other audio playback device is connected here, you’ll be able to listen to its playback through the LX-15e. The volume of the device connected to the Input jack can be adjusted by means of Input Volume (p. 51).

Convenient Functions

Function Mode

Appendix

* To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn o the power on all devices before making any

connections.

* When connection cables with resistors are used, the volume level of equipment connected to the Input jack may be low. If this happens, use connection cables that do

not contain resistors.



Before You Play

Opening/Closing the Lid

NOTE

To open the lid, use both hands to lift it lightly. The lid of the LX-15e is designed to close softly even if you remove your hands from it. However, it will close quite abruptly if it has been opened only slightly. Be careful not to pinch your ngers in the gap.

1. To open the lid, use both hands to lift it. 2. To close the lid, use both hands to gently lower it.

NOTE

If you need to move the piano, make sure the lid is closed rst to prevent accidents.

Opening/Closing the Top Lid

Opening the lid will make the sound more sharply dened; closing the lid produces a more mellow sound.

NOTE

• The top lid must be opened or closed by an adult.

• Do not force the top lid backward; doing so will damage it.

• Be careful not to pinch your ngers in the gap.

Opening the Top Lid

1. Lift up the top lid with both hands.

Closing the Top Lid

1. Lift up the top lid with both hands.

2. Gently lower the top lid.

Top lid

Using the music rest

You can place music books or sheet music on the top edge of the opened lid.

Tips for placing music

• Insert the sheet music into the groove on the top edge of the lid.

• Crease sheet music so that it will stay open. If this does not work, use paper clips to secure it.

• If the sheet music is thin, attach it to a clipboard before placing it on the music Rest.

Before You Play

Turning the Power On/O

NOTE

• Once everything is properly connected (p. 15), be sure to follow the procedure below to turn on their power. If you turn on equipment in the wrong order, you risk causing malfunction or equipment failure.

• Before turning the unit on/o, always be sure to turn the volume down. Even with the volume turned down, you might hear some sound when switching the unit on/o. However, this is normal and does not indicate a malfunction.

O

Turning the power on

1. Move the [Volume] slider all the way to the left to

minimize the volume.

Min Max

Turning the power o

1. Move the [Volume] slider all the way to the left to

minimize the volume.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

2. Press the [Power] switch.

After a brief interval, you’ll be able to produce sounds by playing the keyboard.

* This unit is equipped with a protection circuit. A brief interval

(a few seconds) after power up is required before the unit will operate normally.

2. Press the [Power] switch.

The power is turned o.

* If you need to turn o the power completely, rst turn o the

unit, then unplug the power cord from the power outlet. Refer to “Power Supply” (p. 5).

3. Use the [Volume] slider to adjust the volume.

Adjust the volume while playing something on the keyboard, so you can hear how it sounds.

This will adjust the volume of the speakers if you’re using the speakers of the unit, or the volume of the headphones if headphones are connected. Each volume setting (for speaker or headphone) is saved automatically.

Volume adjustment screen when using speakers

MEMO

The LX-15e is designed so that nuances in the dynamics of your playing will be clearly heard even at low volume, and that the sound will remain clear even at high volume.

Volume adjustment screen when using headphones

WARNING

If you don’t want the power to turn o automatically, change the “Auto O” setting to “O”!

The power to this unit will be turned o automatically after a predetermined amount of time has passed since it was last used for playing music, or its buttons or controls were operated (Auto O function).

If you do not want the power to be turned o automatically, disengage the Auto O function (p. 44).

Convenient Functions

Function Mode

NOTE

• Any settings that you are in the process of editing will be lost when the power is turned o. If you have any settings that you want to keep, you should refer to “Retaining the Settings Even After Power-o (Memory Backup)” (p. 44) and save your settings.

• To restore power, turn the power on again (p. 17).

• When turning the power on again, you must allow at least ve seconds after power-o before you once again turn the power on. If you fail to allow enough time, the Auto O function might not be reset, preventing the power from turning on correctly.

Appendix



Performing

Performing with Various Sounds

In addition to piano sounds, the LX-15e lets you enjoy performing with many other sounds (350 types). These sounds are called “Tones.” The Tones are categorized into ve groups, each of which is assigned to a dierent Tone button.

Switching Tones

Let’s start by performing with a piano tone. When you turn on the power, the “ConcertPiano” tone is selected.

1. Press a tone button to select the tone group.

The currently selected tone number and tone name are displayed.

Tone groups

Tone button Description

Piano [Grand] button Selects grand piano sounds.

Piano [Upright] button Selects upright piano sounds

[E. Piano] button Selects various electric piano sounds used in pop or rock.

[Strings] button Selects the sounds of string instruments such as violins, as well as other instruments used in orchestras.

Selects a variety of sounds such as organ, bass, or accompaniment sounds.

[Other] button

For details on the tones, refer to “Tone List” (p. 58). *1 Rotary eect:

Rotary is an eect which simulates the sound of rotating speakers. There is a choice of two settings: Fast and Slow.

* If you select tone numbers 43–51, you’ll be able to use the keyboard to play the sounds of a drum set. * If you’ve selected an organ sound that provides a rotary eect (*1), such as a Combo Jz. Org or a Ballad Organ, pressing the [Other]

button will switch the speed of the rotary eect.

2. Use the [–] [+] buttons to select a variation within the tone group.

* If you’ve selected a drum set tone or an SFX set tone, some notes of the keyboard will not produce sound.

Auditioning tones (tone demo)

1. While holding down a tone button, press the [ ] (Play/Stop) button.

A tone demo that uses the rst tone of each tone group will begin playing back.

2. To stop the tone demo, press the [Song] button or the [ ] (Play/Stop) button.

What are eects?

In addition to reverb, the LX-15e provides a wide variety of other “eects” that can modify the sound in various ways. The rotary eect is one of these eects.

Performing

Performing with Two Layered Tones (Dual Play)

You can play two tones simultaneously from each note of the keyboard. This feature is called “Dual Play.” As an example, here’s how to layer piano and strings tones.

1. While holding down the Piano [Grand] button, press the [Strings] button.

Both buttons will light. When you play the keyboard, you’ll hear both the piano and the strings tones.

* Dual play is not available if Split Play (p. 20) or Twin Piano (p. 24) are turned on. * For some combinations of sounds, the eect is not applied to tone 2, and this may aect how the tone sounds. * It’s not possible to layer Piano [Grand] and Piano [Upright] tones together.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Selecting tones for dual play

Tone name Corresponding button How to select tones

Tone 1 Left tone button Press the [–] [+] buttons.

Tone 2 Right tone button While holding down the tone button for Tone 2 (the right-most of the lit Tone buttons), and press the [–] [+] buttons.

2. To exit Dual Play, press one of the tone buttons.

Advanced techniques

Changing the pitch of tone 2 in steps of an octave: “Octave Shift” (p. 52) Specifying the part(s) aected by the damper pedal: “Damper Pedal Part” (p. 52) Adjusting the volume balance of the two tones: “Dual Balance” (p. 51)

Convenient Functions

Function Mode

Appendix

Performing

Playing Dierent Tones with the Right and Left Hands (Split Play)

You can play dierent tones in the left and right sides of the keyboard, divided at a certain key. This feature is called “Split Play,” and the key at which the keyboard is divided is called the “Split Point.”

1. While holding down the [Transpose] button, press the [Twin Piano] button.

The Split screen will appear.

When Split is turned on, the keyboard settings will be as follows.

Split Point (Power-up default: F 3)

Left-hand Tone Right-hand Tone

2. To exit Split Play, hold down the [Transpose] button and press the [Twin Piano] button once again.

* Depending on which tones are being used together, the tones might sound dierent because no eect is applied to the left-hand zone.

Advanced technique

Specifying the part(s) aected by the damper pedal: “Damper Pedal Part” (p. 52)

Changing the right-hand tone

1. Press a tone button.

The number and name of tone currently selected for the right-hand zone are shown.

2. Press the [–] [+] buttons.

A dierent tone is selected.

Performing

Changing the left-hand tone

1. While holding down the [Transpose] button and [Twin Piano] button, press a tone button.

The number and name of the tone currently selected for the left-hand zone are shown.

2. While holding down the [Transpose] button and [Twin Piano] button, press the [–] [+] buttons.

A dierent tone is selected.

Advanced technique

Changing the pitch of the left-hand tone in steps of an octave: “Octave Shift” (p. 52)

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Changing the keyboard’s split point

Range in which you can specify the split point (B1–B6)

Split Point

Power-up default: F 3

The Split Point belongs to the left-hand

1. While holding down the [Transpose] button and [Twin Piano] button, press the key that you want to assign as the split point.

The key you pressed becomes the new split point, and that key will be shown in the display.

Screen Value

B1–B6

(default: F#3)

section of the keyboard

Saving your settings

The LX-15e’s settings will revert to the default values when you turn o the power, but you can save them as described in “Retaining the Settings Even After Power-o (Memory Backup)” (p. 44).

Convenient Functions

Function Mode

Appendix

Performing

Adjusting the Sound to Your Taste

The LX-15e lets you add reverberation or modify the brightness of the sound.

Changing the clarity of the sound (opening/closing the lid)

Opening the lid will make the sound more sharply dened; closing the lid produces a more mellow sound (p. 16).

Adding Reverberation to the Sound (Ambience)

You can add a pleasant reverberation to the sounds of the LX-15e, producing the impression that you are performing in a concert hall. This eect is called “Ambience.”

1 3

Saving your settings

1. Press the [Ambience] button.

The [Ambience] button will light.

2. While holding down the [Ambience] button, press the [–] [+] buttons.

The display will indicate the depth of the ambience eect values.

Screen Value Explanation

1–10

(default: 2)

Higher values apply deeper ambience.

* If you’re using headphones and the Headphones 3D Ambience eect (p. 51) is set to “On,” this lets you adjust the

depth of the Headphones 3D Ambience eect.

3. To turn o the ambience eect, press the [Ambience] button once again.

The [Ambience] button will go out.

* It’s not possible to specify the depth of ambience individually for each tone. The eect will be applied in the same way to each tone.

Performing

Adjusting the Brightness of the Sound (Brilliance)

You can adjust the brightness of the sounds played on the keyboard or played back by a song.

1 3

1. Press the [Brilliance] button.

The [Brilliance] button will light.

2. While holding down the [Brilliance] button, press the [–] [+] buttons.

The display will indicate the depth of the brilliance eect values.

Screen Value Explanation

-10–0–10

(default: 5)

Positive (+) values make the sound brighter; negative (-) values make the sound more mellow.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Saving your settings

3. To turn o the brilliance eect, press the [Brilliance] button once again.

The [Brilliance] button will go out.

Adjusting the Keyboard Response (Key Touch)

The way in which the keyboard responds to your playing strength can be adjusted to your personal taste.

1 3

1. Press the [Key Touch] button.

The [Key Touch] button will light.

2. While holding down the [Key Touch] button, press the [–] [+] buttons.

The display will indicate the key touch setting.

Saving your settings

Convenient Functions

Function Mode

Screen Value Explanation

Fix, 1–100

(default: 70)

Higher values will make the keyboard feel heavier. If you’ve specied “Fix”, notes will sound at the same volume regardless of how strongly you play the keyboard. If this value is 50, the result will be the same as when the [Key Touch] button is unlit.

3. To cancel key touch, press the [Key Touch] button once again.

The [Key Touch] button will go out.

Appendix

Performing

Dividing the Keyboard for Two-Person Performance (Twin Piano)

You can divide the keyboard into left and right zones so that two people can play the same range of pitches, just as though there were two pianos. This function is called “Twin Piano.” For example, you could use Twin Piano to allow a student to play along with their teacher.

Conventional keyboard

Twin Piano

1. Press the [Twin Piano] button.

The [Twin Piano] button will light, and the “ConcertPiano” tone will be selected.

When you turn Twin Piano on, the keyboard and pedal settings will be as shown in the illustration.

NOTE

If Twin Piano is on, damper resonance will not be applied; this may cause the piano to sound dierent.

The damper pedal for the left area

divide point

The damper pedal for the right area

2. Select the tone to be played (p. 18).

The left and right sections will have the same tone.

3. To cancel Twin Piano, press the [Twin Piano] button once again.

The [Twin Piano] button will go out.

Changing the way in which the sound is heard (twin piano mode)

1. While holding down the [Twin Piano] button, press the [–] [+] buttons.

The display will indicate Twin Piano mode.

Screen Value Explanation

The sound of the right-hand keyboard zone will be heard more loudly from the right speaker than

Pair

Individual

(default)

from the left speaker. The sound of the left-hand keyboard zone will be heard more loudly from the left speaker than from

the right speaker. When using headphones, you’ll be able to hear the other person’s playing.

The sound of the right-hand keyboard zone will be heard only from the right speaker. The sound of the left-hand keyboard zone will be heard only from the left speaker. When using headphones, you won’t be able to hear the other person’s playing.

* Ambience will turn o. * For some tones, the sound might not be divided to left and right. * If using headphones, connect them to the left Phones jack if playing the left keyboard zone; connect

them to the right Phones jack if playing the right keyboard zone.

* If you record while this is set to Individual, the playback might not be the same as what you heard

during recording.

Saving your settings

Performing

Shifting the Pitch (Transpose)

“Transpose” means to shift the pitches of songs and the keyboard. The Transpose function makes it easy to do the following.

• You can use unchanged ngering to accompany a singer who is singing in a key dierent than the original music.

• A song written in a dicult key with numerous sharps (

• Notation of a transposing instrument such as trumpet or sax can be played as written, while hearing the transposed pitches.

For example if the song is written in E major but you want to play it using the ngering of the key of C major, you would set Transpose to “4.”

If you play C E G It will sound E G B

MEMO

With the factory settings, both the song and the keyboard will be transposed. If you want to transpose only the keyboard or only the song, make the appropriate setting as described in “Specifying What the Transpose will Aect (Transpose Mode)” (p. 52).

) or ats ( ) can be performed in a key that’s easier for you to play.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

1 3

1. Press the [Transpose] button.

The [Transpose] button will light.

2. While holding down the [Transpose] button, press the [–] [+] buttons.

The display will indicate the amount of transposition.

Screen Value Explanation

-6–0–5 (semitone units)

(default: 1)

MEMO

You can also specify this value by holding down the [Transpose] button and playing the note that is the tonic of the key to which you want to transpose.

* If you select a dierent song, the transposition setting will be canceled.

Positive (+) values raise the pitch in semitone steps, and negative (-) values lower the pitch in semitone steps.

3. To cancel the transposition, press the [Transpose] button once again.

The [Transpose] button will go out.

Convenient Functions

Function Mode

Appendix



Practicing

Practicing with the Metronome

You can sound the metronome while you practice. While the song plays, the metronome will sound at the tempo and time signature of the song.

1. Press the [Metronome] button.

The [Metronome] button will blink, and the metronome will sound.

The [Metronome] button will blink red and green according to the currently selected time signature; red indicates the strong beats, and green indicates the weak beats.

2. To stop the metronome, press the [Metronome] button once again.

The [Metronome] button will go out.

Changing the Tempo

1. Press the [ ] [ ] (Slow/Fast) buttons.

Tempo

When you play back a song, the metronome’s tempo will be set to the tempo of that song.

Changing the Time Signature

1. While holding down the [Metronome] button, press the [ ] [ ]

(Slow/Fast) buttons.

Time signature

If you specify “0/4” only the weak beats will sound. When you play back a song, the metronome’s time signature will be set to the time signature of that song.

Available time signatures

* You can’t change the metronome’s time signature while a song is playing. * If you record using 0/4, the song’s time signature will be set to 4/4 when you save it.

2/2, 0/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 9/8, 12/8

(default: 4/4)

Practicing

Adjusting the Metronome’s Volume

1. While holding down the [Metronome] button,

press the [–] [+] buttons.

The display will indicate the metronome’s volume.

Screen Value Explanation

0–10

(default: 5)

When the volume of the metronome is set to “0,” the metronome won’t sound, but the [Metronome] button will blink.

Adding a Count-in to Synchronize Your Performance

A series of sounds rhythmically played to indicate the tempo before a song starts is called a “count-in.” If you sound a count-in, it will be easier for you to synchronize your own performance to the tempo of the playback.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

1. Press the [Metronome] button.

The metronome will sound.

2. Press the [ ] (Play/Stop)

button.

A two-measure count sound will be produced before the song starts playing.

1 2

Convenient Functions

Function Mode

Appendix

Practicing

Practicing with a Song

You can practice by playing along with a song.

Selecting and Playing a Song

Here’s how to listen to the built-in songs. The LX-15e provides over 200 built-in piano songs. You can also play back songs stored on a separately sold USB ash drive.

1. Press the [Song] button.

The song screen will appear.

2. While holding down the [Song] button,

use the [–] [+] buttons to select the category.

Playing Songs Consecutively (All Songs Play)

You can consecutively play back the built-in songs or the songs saved in Favorite (internal memory) or on a USB (USB ash drive). This function is called “All Songs Play.”

1. While holding down the [Song] button, use the [–] [+] buttons to select the category.

2. While holding down the [Song] button, press the [ ] (Play/Stop) button.

All Songs Play will be selected, and the [ ] (Play/Stop) button will blink.

* All Song Play will be cancelled if you stop playback or turn o the power.

Adjusting the Volume Balance of the Song and the Keyboard Performance (Song Balance)

You can adjust the balance between the song and your keyboard performance by changing the volume of the song.

1 3

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

1. Press the [Song Balance] button.

The [Song Balance] button will light.

2. While holding down the [Song Balance] button, press the [–] [+] buttons.

The display will show the song balance.

Screen Value Explanation

0–9

(default: 5)

The song’s volume decreases the more you lower this value, and time the keyboard performance will take on more prominence. The song’s volume increases the more you raise this value, and at the same time the keyboard performance will become less prominent.

3. To cancel the Song Balance function, press the [Song Balance] button once again.

The [Song Balance] button will go out.

Adjusting a Song’s Tempo for Easier Practicing

You can change the tempo at which a song plays back. When you’re practicing along with a song, this allows you to slow down the tempo of a dicult song in order to play it more comfortably.

1. Press the [ ] [ ] (Slow/Fast) buttons.

The tempo will change.

MEMO

If an audio le is selected, you can adjust the tempo in the range of 75–100–125%.

2. To return the tempo to its original setting, press the [ ] (Slow)

and [ ] (Fast) buttons simultaneously.

Convenient Functions

Function Mode

Playing back at a xed tempo (tempo mute)

With some of the internal songs, the tempo will change during the song. If desired, you can make these songs play back at a xed, unchanging tempo.

1. While holding down the [ ] (Play/Stop) button, use the [ ] [ ] (Slow/Fast) buttons to adjust the tempo.

The tempo indication in the screen will be highlighted.

2. To cancel tempo mute, once again hold down the [ ] (Play/Stop) button and press the [ ] [ ] (Slow/Fast) buttons.

Appendix

Practicing

Practicing One Hand at a Time (Part Mute)

Here’s how to have only the selected part play back. This allows you to practice playing the left or right-hand part of a song while listening to the other hand played automatically.

Part button

Part

Each part is assigned to the part buttons as shown in the illustration.

Muting

You can “mute” a specic part so that it will not be heard.

* If you’ve selected a song that does not contain an

accompaniment, the [Accomp] button will not light even if you press it.

Accompaniment part

Left-hand part

Right-hand part

1. Press the part button for the part that you don’t want to be played.

The light for the button you pressed will go out, and the selected part will not be heard.

MEMO

• If the accompaniment part is muted, playback will skip the introduction.

• The mute setting will be cancelled when you switch songs.

• Although the Part Mute function cannot be used with respect to the playback of an audio le, you can reduce the volume during playback of sounds that are localized at the center of the sound eld, such as vocals or bass. See “Center Cancel” (p. 39).

2. To un-mute the sound, press the part button once again so it’s lit.

Using the sound of a specic part as a “guide” (mute volume)

If desired, you can specify that the sound of a part will play at a reduced volume rather than going completely silent when you press a part button and turn o its indicator.

This setting lets you play a specic part at a reduced volume and use it as a “guide” for your playing.

1. While holding down the part button, press the [–] [+] buttons.

Screen Value Explanation

0–10

(default: 0)

Higher values make the sound louder.

Practicing

Repeatedly Practicing a Portion of a Song (AB Repeat)

Here’s how you can repeatedly play back a specied portion of the song. You can use this function to repeatedly practice that portion.

Section to repeat

Time

A (Repeat Start)

B (Repeat End)

1. Press the [ ] (Play/Stop) button.

The song will play back.

2. Press the [AB Repeat] button at the point where you want to start repeating (point A).

The [AB Repeat] button will blink.

3. Press the [AB Repeat] button at the point where you want to stop repeating (point B).

The [AB Repeat] button will light, and playback will begin repeating.

4. To cancel the repeat function, press the [AB Repeat] button once again.

The [AB Repeat] button will go out, the repeat points you specied will be cleared.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

3 4

MEMO

• The repeat points can be specied in measures of beats for an SMF song, or in 1/100 ths of a second for audio.

• Instead of playing back the song, you can also specify the portion to repeat by using the [

Moving the portion to repeat forward or backward

When AB Repeat is on, you can move the repeated portion forward or backward.

Section to repeat

Time

A (Repeat Start)

1. While holding down the [AB Repeat] button, press the [–] [+] buttons.

The repeated portion will be moved without its length being changed.

A (Repeat Start)

] [ ] buttons.

Convenient Functions

Function Mode

Appendix

Practicing

Recording the Song You’re Practicing

It’s easy to record your own performances. You can play back a recorded performance to check your playing, or perform along with a recorded performance. The LX-15e lets you record in the following ways.

Type of recording Explanation

Parts will be separate.

SMF recording

Audio recording

* SMFs (Standard MIDI Files) use a standard format for music le that was formulated so that les containing music le could be widely compatible,

regardless of the manufacturer of the listening device. An enormous variety of music is available, whether it be for listening, for practicing musical instruments, for Karaoke, etc.

SMF Recording

You can re-record a specic portion of the song. You can overdub.

* Normally, you should use SMF recording.

Your performance will be recorded as audio data. The recorded song can be used on your computer.

* In order to use audio recording, you must connect a USB ash drive (sold separately) to the USB memory port (p. 15). * Thanks to its multiple number of speakers, each of which can be used to play a dierent portion of the overall sound, the LX-15e is capable of

producing piano sounds that possess great depth and seem to have three-dimensional presence. Such eects are produced when you play something on the keyboard, or when you play back a song that's been recorded as an SMF. However, when you make an audio recording, the song will consist of two channels (stereo), and such eects cannot be reproduced.

To record a new song, proceed as follows. This method is convenient when you simply want to record your performance as easily as possible.

Getting ready to record

Select the tone that you want to use for performing (p. 18).

2. Press the [ ] (Rec) button.

The [ ] (Rec) button will light, the [ ] (Play/Stop) button will blink, and the LX-15e will enter recording-standby mode.

If you decide not to record, press the [

] (Rec) button once again.

3. If desired, sound the metronome (p. 26).

MEMO

If you change the metronome’s tempo and time signature, they will be recorded with the song, allowing the metronome to sound correctly during playback.

Starting/stopping recording

Press the [ ] (Play/Stop) button.

A two-measure count will be heard (the measure number will be shown as “-2” then “-1” in the lower right of the display), and then recording will start.

When recording starts, the [ will light.

MEMO

You can also initiate recording by simply playing the keyboard. If you initiate recording by playing the keyboard, a count will not be sounded.

] (Rec) button and [ ] (Play/Stop) button

2. Press the [ ] (Play/Stop) button.

Recording will stop, and you’ll be presented with a message asking you if you want to save the performance or erase it.

1 2

Practicing

Saving a performance you’ve recorded

* If you want to save to the USB ash drive (sold separately), connect your USB ash drive to the USB memory port before you continue.

1. Use the [+] button to select “Save.”

2. Press the [Song] button.

The media select screen will appear.

3. Use the [–] [+] buttons to select the save-destination media.

Indication Save-destination media

Favorite Internal memory

USB Memory USB ash drive

* If a USB ash drive (sold separately) is not connected, you won’t be able to select “USB Memory.”

4. Press the [ ] (Fast) button.

A screen will appear, allowing you to select the song number of save destination.

5. Use the [–] [+] buttons to select the song number of save destination.

No song has been saved in song numbers shown as (Empty) in the song name column. Choose a song number in which no song has been saved. If you want to save your song by overwriting an existing song you no longer need, select the song number of that unwanted song.

6. Press the [ ] (Fast) button.

A screen will appear, allowing you to specify a name for your song.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

7. Edit the song name using the buttons shown in the illustration below.

Use the [Song] button to select the position at which you want to specify a character.

Use the [–] [+] buttons to change the character.

Select the character to changeChange the character

8. When you’ve nished specifying a song name, press the [ ] (Fast) button to access the

save-conrmation screen.

9. Press the [Song] button to save the song.

If you decide not to save the song, press the [ ] (Slow) button.

NOTE

Never turn o the power or disconnect the USB ash drive while the screen indicates “Executing...”

Erasing a performance you’ve recorded

1. Use the [ ] (Slow) button to select “Erase.”

A message will ask you to conrm that you want to erase the song.

2. Press the [ ] (Fast) button to erase the song.

Convenient Functions

Function Mode

Listening to a performance you’ve recorded

1. Press the [ ] (Play/Stop) button.

Playback will start from the beginning of the recorded performance.

Appendix

Practicing

Overdubbing a Recorded Song

When recording an SMF, you can overdub each part separately. For example, you can record the left-hand and right-hand parts separately, or record along with a song.

Recording each hand separately

You can separately record your left-hand performance to the [Left] button and your right-hand performance to the [Right] button. You can also separately re-record each hand afterward.

Getting ready to record

Select the tone that you want to use for performing (p. 18).

2. Press the [ ] (Rec) button.

The [ ] (Rec) button will light, the [ ] (Play/Stop) button will blink, and the LX-15e will enter recording-standby mode.

If you decide not to record, press the [

] (Rec) button once again.

3. If desired, sound the metronome (p. 26).

MEMO

If you change the metronome’s tempo and time signature, they will be recorded with the song, allowing the metronome to sound correctly during playback.

Recording the left hand

Press the [Right] button and the [Accomp] button so

their illumination is turned o.

The [Left] button alone will start blinking, meaning that the unit is ready to record to the [Left] button.

* If you don’t specify a part at this time, the recorded performance will be recorded in this order: [Right] button * If you’re using Twin Piano or Split Play, the left side or left-hand tone will be recorded to the [Left] button, and the right side or right-hand tone will

be recorded to the [Right] button.

2 3

[Left] button [Accomp] button.

2. Press the [ ] (Play/Stop) button.

A two-measure count will sound (the measure number in the lower right of the display will indicate “-2,” then “-1”), and then recording will start. When recording starts, the [

MEMO

You can also initiate recording by playing the keyboard. In this case, the count will not sound.

] (Rec) button and [ ] (Play/Stop) button will light.

3. Press the [ ] (Play/Stop) button.

Recording will stop, and a conrmation message will ask whether you want to save or delete the recording.

4. Either save the performance or erase it (p. 33).

Practicing

Overdubbing the right hand

Press the [ ] (Rec) button.

The [ ] (Rec) button will light, and the LX-15e will enter recording-standby mode.

At this time, New Song will be selected. If you decide not to record, press the [

(Rec) button once again.

]

4125

2. Reselect the song you saved earlier by pressing the [+] button.

MEMO

The song’s tempo and time signature will be as they were when you recorded the left hand.

3. Press the [Right] button so it’s blinking.

In this state, the right-hand performance will be recorded to the [Right] button. Leave the [Left] button lit.

NOTE

If you select a previously recorded part and then record, your new performance will overwrite that part; the previously recorded performance will be lost.

4. Press the [ ] (Play/Stop) button.

A two-measure count will be heard (the measure number will be shown as “-2” then “-1” in the lower right of the display), and then recording will start. The previously recorded performance for the left hand will be played back, so you can listen to it while you play the right-hand part. When recording starts, the [

] (Rec) button and [ ] (Play/Stop) button will light.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

MEMO

You can also initiate recording by playing the keyboard. In this case, the count will not sound.

5. Press the [ ] (Play/Stop) button.

Recording will stop, and a conrmation message will ask whether you want to save or delete the recording.

6. Either save the performance or erase it (p. 33).

Convenient Functions

Function Mode

Appendix

Practicing

Recording a performance you play along with a song

Here’s how you can record a performance that you play along with a song.

Getting ready to record

Select the tone that you want record (p. 18).

2. Select the song to be dubbed (p. 28).

3. Press the [ ] (Rec) button.

The [ ] (Rec) button will light, and the LX-15e will enter recording-standby mode. At this time, New Song will be selected. If you decide not to record, press the [

] (Rec) button once again.

4. Reselect the song selected in step 2 by pressing the [+] button.

MEMO

The song’s tempo and time signature will be according to the settings of the song you selected.

5. Press the part button of the part that you want to record, so it’s blinking.

Parts whose buttons are lit will play back during recording.

MEMO

If you want to re-record only a portion of the song, use the [ want to start recording.

] (Bwd) button or [ ] (Fwd) button to move to the measure at which you

Starting/stopping recording

Press the [ ] (Play/Stop) button.

A two-measure count will be heard (the measure number will be shown as “-2” then “-1” in the lower right of the display), and then recording will start.

When recording starts, the [ will light.

] (Rec) button and [ ] (Play/Stop) button

1 2

MEMO

You can also initiate recording by simply playing the keyboard. If you initiate recording by playing the keyboard, a count will not be sounded.

2. Press the [ ] (Play/Stop) button.

Recording will stop, and a conrmation message will ask whether you want to save or delete the recording.

3. Either save the performance or erase it (p. 33).

Practicing

Converting a Song Recorded as an SMF to Audio

By converting a song recorded in the form of an SMF to audio, you’ll be able to listen to it on your computer. You can also use your computer to burn the song to a music CD, or upload it to the Internet.

Copying an audio recording of a song to your computer

If you save an audio recording of a song on a USB ash drive, you'll be able to listen to it on your computer.

In order for an SMF song recording to be used on your computer, you’ll need to convert it to audio (WAV le).

Audio recordings of songs are saved as WAVE les (16-bit, 44.1 kHz).

You can use your computer to burn them to a music CD or upload them to the Internet.

A song recorded on the LX-15e can be copied to your computer by means of a USB ash drive.

page 40

WAV

Use computer software (such as iTunes) to burn the song to a CD.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

1. Connect a USB ash drive (sold separately) to the USB memory

port (p. 15).

* Audio data cannot be saved in Favorite (internal memory).

2. Select the song that you want to convert to audio (p. 28).

3. While holding down the [ ] (Rec) button, press the [–] [+] buttons

to select “Audio.”

4. Press the [ ] (Rec) button.

The [ ] (Rec) button will light, and the [ ] (Play/Stop) button will blink; the LX-15e will enter converting-standby mode. At this time, New Song will be selected. If you decide not to convert, press the [

] (Rec) button once again.

5. Reselect the song selected in step 2 by pressing the [+] button.

6. Press the [ ] (Play/Stop) button.

The song will play back, and the conversion will begin.

MEMO

If, during conversion, you play the keyboard, input something via the USB port (USB MIDI), or input sound via the Input jack, all sound including those sounds will be converted. Muted parts will not be converted.

NOTE

• Never turn o the power or disconnect the USB ash drive during conversion.

• For some SMF recordings, it might not be possible to perfectly convert the recording in its original form.

7. Press the [ ] (Play/Stop) button.

Song playback will stop, and the section that was played back will be converted. A conrmation message will ask whether you want to save or delete the le.

476

Convenient Functions

Function Mode

8. Either save the performance or erase it (p. 33).

Appendix

Practicing

Audio Recording

Here’s how to record what you play on the LX-15e as audio data. The recorded song can be used on your computer.

* Thanks to its multiple number of speakers, each of which can be used to play a dierent portion of the overall sound, the LX-15e is capable of

producing piano sounds that possess great depth and seem to have three-dimensional presence. Such eects are produced when you play something on the keyboard, or when you play back a song that’s been recorded as an SMF. However, when you make an audio recording, the song will consist of two channels (stereo), and such eects cannot be reproduced.

Preparing to record

Connect a USB ash drive (sold separately) to the

USB memory port (p. 15).

* Audio data cannot be saved in Favorite (internal memory).

2. Select the tone that you want perform (p. 18).

3. While holding down the [ ] (Rec) button, press the [–] [+] buttons to select “Audio.”

4. Press the [ ] (Rec) button.

The [ ] (Rec) button will light, the [ ] (Play/Stop) button will blink, and the LX-15e will enter recording-standby mode. If you decide not to record, press the [

] (Rec) button once again.

5. If desired, sound the metronome (p. 26).

Starting/stopping recording

Press the [ ] (Play/Stop) button.

Recording will start. When recording starts, the [

will light.

NOTE

Never turn o the power or disconnect the USB ash drive during recording.

] (Rec) button and [ ] (Play/Stop) button

2. Press the [ ] (Play/Stop) button.

Recording will stop, and a conrmation message will ask whether you want to save or delete the recording.

3. Either save the performance or erase it (p. 33).

1 2

Practicing

Transposing a Song for Easier Performance (Audio Transpose)

An audio recording of a song, or a song from a digital audio player connected to the Input jack can be transposed to make it play back in a dierent key. You can play the keyboard while listening to the transposed sound.

1. Press the [Transpose] button.

The [Transpose] button will light.

2. While holding down the [Transpose] button, press the [–] [+] buttons.

The display will indicate the amount of transposition.

Screen Value Explanation

-6–0–5(semitone units)

(default: 1)

MEMO

• With the factory settings, transposition will be applied to the selected audio le and the sound of the digital audio player connected to the Input jack, as well as to the sound of the keyboard. If you want transposition to aect only the keyboard or only the audio le and the sound from the Input jack, make the appropriate setting as described in “Specifying What the Transpose will Aect (Transpose Mode)” (p. 52).

• You can also use the Function mode’s “Audio Transpose” setting to change the amount of transposition (p. 51).

* If you select a dierent song, the audio transposition setting will be canceled.

3. To cancel the transposition, press the [Transpose] button once again.

The [Transpose] button will go out.

Positive (+) values raise the pitch in semitone steps, and negative (-) values lower the pitch in semitone steps.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Enjoying Karaoke with an Audio File (Center Cancel)

When playing back an audio le, you can minimize the sounds that are heard from the center. For example, this allows you to minimize the melody or vocal on a music CD, so that you can play or sing that part instead.

MEMO

Center Cancel will apply both to the selected audio le and to the digital audio player that’s connected to the Input jack.

* For some songs, it might not be possible to completely eliminate the melody sound.

1. Press the [Right] button.

The [Right] button will go out, and the melody sound will be minimized.

MEMO

You can also use the Function mode’s “Center Cancel” setting to turn this o (p. 51).

* The Center Cancel setting will turn o if you select a dierent song.

2. When you want the sound to be heard, press the [Right] button once again.

The [Right] button will light.

Convenient Functions

Function Mode

Appendix

Burning an Audio Recording of a Song (WAV le) to a CD

After an audio recording of a song has been saved to a USB ash drive, you can copy it to your computer and burn it to a CD. If you want to burn a CD from a song that you recorded as an SMF, you must rst convert it to audio (WAV le) (p. 37).

In order to burn a CD on your computer, you’ll need software such as “iTunes.”

For details, refer to the owner’s manual or the online help of your software.

Copy the recorded song to your computer

A song recorded on the LX-15e can be copied to your computer by means of a USB ash drive.

WAV

Use computer software (such as iTunes) to burn the song to a CD.

1. Connect the USB ash drive

containing the song to your computer.

If you’re using Windows, a “Removable disk” icon will appear in “Computer.” If you’re using Mac OS X, a “NO NAME” icon will appear on the desktop.

2. Double-click the icon that appeared.

The contents of the USB ash drive will be displayed. The audio recording of the song (WAV le) will be among the

contents.

Use iTunes to burn the song to CD

The following explanation uses iTunes 10 for Windows. If you’re using a dierent version or other software, refer to its online help or owner’s manual.

1. From the Start menu, click [All Programs] - [iTunes].

2. From the iTunes [File] menu, click [New Playlist] to create

a playlist.

3. Copy the song (WAV le) that you want to burn to CD to

your computer’s desktop or another location where you can easily nd it.

Copy to desktop

5. Select the playlist that you created in step 2, and in the

[File] menu, click [Burn playlist to Disc].

Newly created playlist

3. From the desktop (or other location) where you copied

it, drag and drop the song (WAV le) to add it to the playlist you created in step 2.

Drag & drop

4. Insert a blank CD-R into your computer.

6. Make the appropriate settings in the disc creation dialog

box, and then click the [Burn] button.

Practicing

Renaming a Song

Here’s how to rename a song you’re saved.

1. Select the song that you want to rename (p. 28).

2. While holding down the [Key Touch] button, press the [Transpose] button.

The [Key Touch] button and [Transpose] button will light, and the LX-15e will enter Function mode.

3. Use the [ ] [ ] (Slow/Fast) buttons to select “Save Song.”

4. Press the [Song] button.

The media select screen will appear.

5. Use the [–] [+] buttons to select the save-destination media.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

863

6. Press the [ ] (Fast) button.

A screen will appear, allowing you to select the song number of save destination.

7. Use the [–] [+] buttons to select the song number of save destination.

8. Press the [ ] (Fast) button.

A screen will appear, allowing you to specify the song name.

9. Edit the song name using the buttons shown in the illustration below.

Use the [Song] button to select the position at which you want to specify a character.

Use the [–] [+] buttons to change the character.

Select the character to changeChange the character

10. When you’ve nished editing the song name, press the [ ] (Fast) button to access conrmation screen.

11. Press the [Song] button to rename the song.

If you decide not to rename the song, press the [ ] (Slow) button. When the song has been renamed, you will return to the screen of step 3.

Convenient Functions

Function Mode

NOTE

Never turn o the power or disconnect the USB ash drive while the screen indicates “Executing...”

12. Press the [Key Touch] button or the [Transpose] button to nish the procedure.

Appendix



Personalizing Your Piano Sound (Piano Designer)

What is Piano Designer?

The LX-15e allows you to personalize your piano sound by adjusting various factors that aect the sound, such as the piano’s strings, the resonance produced using the pedals, and the sound of the hammers striking the strings.

This function is called “Piano Designer.”

Making Detailed Adjustments to the Piano Sound

Hammer Noise

Adjusting the piano sound to your taste

String Resonance

Temperament

1. While holding down the Piano [Grand] button, press the Piano [Upright] button.

The Piano Designer screen will appear.

The “ConcertPiano” tone will be selected.

2. Press the [ ] [ ] (Slow/Fast) buttons to select the item that you want to edit.

3. Use the [–] [+] buttons to adjust the value.

4. Repeat steps 2–3 to adjust the piano sound to your taste.

5. When you’re nished using Piano Designer, press the Piano [Grand] button or the Piano

[Upright] button.

Piano designer parameter

Parameter Value Description

Adjusts the extent to which the lid of the grand piano is open. The sound will become more mellow as you close the lid of the piano in the screen. The sound will become brighter as you

open the lid of the piano in the screen. This adjusts the damper resonance of the acoustic piano sound (the sympathetic vibration produced in strings other than

those actually played when you press the damper pedal). Higher settings will make the sympathetic vibration louder.

This adjusts the sound produced when the hammer of an acoustic piano strikes the string. Higher settings will produce a louder sound of the hammer striking the string.

This adjusts the time from when you play a key until the piano sound is heard. Higher settings will produce slower response.

This adjusts the sympathetic vibrations of an acoustic piano’s Duplex Scale. Higher settings will make the sympathetic vibration louder.

This adjusts the metallic resonance that is produced when you play strongly on an acoustic piano. Higher settings will produce a louder metallic sound.

This adjusts the string resonance of the acoustic piano sound (the sympathetic vibrations of strings for previously played notes that occur when you play another note).

Higher settings will make the sympathetic vibration louder.

Lid

Damper Resonance

Hammer Noise

Hammer Response

Duplex Scale

Dynamic Harmonic

String Resonance

0–6

(default: 4)

O, 1–10

(default: 5)

-2–0–2

(default: 0)

O, 1–10

(default: 2)

O, 1–10

(default: 5)

O, 1–10

(default: 5)

O, 1–10

(default: 5)

Saving your settings

Personalizing Your Piano Sound (Piano Designer)

Parameter Value Description

Key O Resonance

Cabinet Resonance

Soundboard Behavior

Damper Noise

Master Tuning

Temperament

Temperament Key

Stretch Tuning

Note Volume

Note Character

O, 1–10

(default: 5)

O, 1–10

(default: 4)

O, 1–10

(default: 5)

O, 1–10

(default: 4)

415.3–440.0–466.2 Hz

(default: 440.0 Hz)

Equal, Just Major, Just Minor, Pythagorean, Kirnberger, Meantone, Werckmeister, Arabic

(default: Equal)

C–B

(default: C)

O, Preset 1, Preset 2 (User: -50–0–+50)

(default: Preset 1)

O, User (User: -50–0)

(default: O )

O, User (User: -5–0–+5)

(default: O )

For some parameters, you can listen to a demo song.

This adjusts sympathetic vibrations such as an acoustic piano’s key-o sound (the subtle sound that occurs when you release a note).

Higher settings will make the sympathetic vibration louder.

Adjusts the body resonance of the grand piano itself. Higher values will produce a larger body resonance.

When you play a chord, this setting improves the clarity of the individual notes in the chord, creating a more beautiful resonance.

Higher settings produce a clearer resonance. This adjusts the damper noise of the acoustic piano sound (the sound of the damper releasing the strings when you press

the damper pedal).

* No damper noise will be heard if Damper Resonance is set to “O.” This adjusts the LX-15e’s standard pitch (the pitch of the middle A note).

When playing ensemble with other instruments and in other such instances, you can match the standard pitch to another instrument.

The standard pitch generally refers to the pitch of the note that’s played when you nger the middle A key. For a cleaner ensemble sound while performing with one or more other instruments, ensure that each instrument’s standard pitch is in tune with that of the other instruments. This tuning of all the instruments to a standard pitch is called “master tuning.”

You can play classical styles such as Baroque using historic temperaments (tuning methods). Most modern songs are composed for and played in equal temperament, the most common tuning in use today. But at one

time, there were a wide variety of other tuning systems in existence. By playing in the temperament that was in use when a composition was created, you can experience the sonorities of

chords originally intended for that song. For details, refer to “Temperaments.”

When playing with tuning other than equal temperament, you need to specify the temperament key for tuning the song to be performed (that is, the note that corresponds to C for a major key or to A for a minor key).

If you choose an equal temperament, there’s no need to select a temperament key.

This lets you specify the amount of “stretch tuning,” a tuning method specically for pianos, in which the high range is

, User

tuned slightly sharper, and the low range is tuned slightly atter. If you select “User,” you’ll be able to edit the stretched tuning yourself. Play the key whose pitch you want to adjust, then use

the [–] [+] buttons to adjust its pitch.

This lets you adjust the volume of each individual key. Higher settings will make the volume louder. If you select “User,” you’ll be able to edit the Note Volume settings. Press the key whose volume you want to adjust, and use the [–] [+] buttons to adjust its volume.

This lets you adjust the tonal character of each individual key. Higher settings will make the tone harder, and lower settings will make the tone softer.

If you select “User,” you’ll be able to adjust the Note Character settings. Press the key whose tone you want to adjust, and use the [–] [+] buttons to adjust its tone.

1. In step 2, choose “Piano Designer Demo.”

Piano Designer Demo

2. Press the [Song] button.

3. Use the [ ] [ ] (Slow/Fast) buttons to select the type of demo.

4. Press the [ ] (Play/Stop) button.

The demo will begin.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Temperaments

Temperament Qualities

Equal In this tuning, each octave is divided into twelve equal steps. Every interval produces about the same amount of slight dissonance.

Just Major

Just Minor The Just tunings dier from major and minor keys. You can get the same eect with the minor scale as with the major scale.

Pythagorean

Kirnberger

Meantone This scale makes some compromises in just intonation, enabling transposition to other keys. Werckmeister This temperament combines the Meantone and Pythagorean tunings. Performances are possible in all keys (rst technique, III). Arabic This tuning is suitable for the music of Arabia.

This tuning eliminates ambiguities in the fths and thirds. It is unsuited to playing melodies and cannot be transposed, but is capable of beautiful sonorities.

This tuning, devised by the philosopher Pythagoras, eliminates dissonance in fourths and fths. Dissonance is produced by third-interval chords, but melodies are euphonious. This is an improvement of the Meantone and Just tunings that provides a high degree of freedom of modulation. Performances are possible

in all keys (III).

What is the duplex scale?

The Duplex Scale is a system of sympathetically vibrating strings sometimes included in grand pianos. These sympathetically vibrating strings are not struck directly with hammers, but sound by vibrating in sympathy with the vibrations of other strings. By resonating with

the overtones, these strings add richness and brilliance to the sound. These sympathetic strings are added only to the high register above approximately C4. Since they do not have a damper (a mechanism that stops them from sounding), they will continue sounding even after you play a note and then release it to stop the sound of the string that was actually struck.

Convenient Functions

Function Mode

Appendix



Convenient Functions

Adjusting the Brightness of the Display (Display Contrast)

You can adjust the brightness of the LX-15e’s display.

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Display

Contrast.”

3. Use the [–] [+] buttons to change the setting.

Value

1–10 (default: 5)

* This setting is automatically stored in the LX-15e.

4. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

Making the Power Automatically Turn O After a Time (Auto O)

WARNING

With the factory settings, the LX-15e’s power will automatically be switched o 30 minutes after you stop playing or operating the unit.

If you don’t need the power to turn o automatically, set “Auto O” to the “O” setting as described below.

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Auto O.”

Retaining the Settings Even After Power-o (Memory Backup)

The settings of the LX-15e will return to their factory-set state when you turn o the power. However, you can store the settings so that they will be retained even after the power is turned o.

This is called the “memory backup” function.

Parameters Stored in Memory Backup Page

Piano designer settings p. 42

Ambience (on/o, depth) p. 22

Brilliance (on/o, depth) p. 23

Split Point p. 21

Twin Piano mode p. 24

Key Touch (on/o, value) p. 23

Dual Balance p. 51

Transpose Mode p. 52

Headphones 3D Ambience p. 51

Damper Pedal Part p. 52

MIDI Transmit Channel p. 52

Visual Control Channel p. 53

Volume Limit p. 54

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Memory

Backup.”

3. Press the [Song] button.

The Memory Backup screen will appear.

3. Use the [–] [+] buttons to change the setting.

Value Explanation

O The power will not turn o automatically.

30 (default)

240

* This setting is automatically stored in the LX-15e.

The power will automatically turn o if no operation is performed for 10 minutes.

The power will automatically turn o if no operation is performed for 30 minutes.

The power will automatically turn o if no operation is performed for 240 minutes (4 hours).

4. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

NOTE

When turning the unit’s power back on after it has been shut down due to the Auto O function, always make sure to allow at least ve seconds to pass after the power has been shut o before you turn the power back on. If you turn it back on too rapidly, the Auto O function will not have had enough time to reset itself, and you may not be able to turn on the power in the normal way.

4. Press the [+] button to select “OK.”

5. To execute the function, press the [Song] button.

If you decide to cancel without executing, press the [–] button to select “Cancel” and press the [Song] button.

When the memory backup has been completed, the screen of step 2 will appear.

NOTE

Never turn o the power while the screen indicates “Executing...”

6. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

Restoring the Factory Settings (Factory Reset)

Settings that you’ve stored using the Memory Backup function (p. 44) can be returned to their factory-set state. This is called the “factory reset” function.

NOTE

When you execute “Factory Reset,” all stored settings will be erased and returned to the factory settings.

Convenient Functions

MEMO

This function will not erase the songs from Favorite (internal memory) or USB ash drive (sold separately). If you want to erase Favorite or USB ash drive, “Initializing the Memory (Format Media)” (p. 46).

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Factory

Reset.”

3. Press the [Song] button.

The Factory Reset screen will appear.

4. Press the [+] button to select “OK.”

5. To execute the function, press the [Song] button.

If you decide to cancel without executing, press the [–] button to select “Cancel” and press the [Song] button.

When the factory reset has been completed, the screen will indicate “Power O, then On.”

NOTE

Never turn o the power while the screen indicates “Executing...”

6. Turn the power o, then on again (p. 17).

MEMO

If you choose “Copy All,” all songs except for audio les in the copy-source memory will be copied.

7. Press the [ ] (Fast) button.

8. Use the [–] [+] buttons to select the copy-destination

number.

No song has been saved at song numbers for which (Empty) is shown as the song name.

Select a song number at which no song has been saved. If you want to delete an unwanted song and replace it with the

song you’re copying, select the unwanted song number.

9. Press the [ ] (Fast) button.

A conrmation message will appear.

10. Press the [Song] button to copy the song.

If you decide not to copy, press the [ ] (Slow) button. Once the song has been copied, you’ll be returned to the screen of

step 2.

NOTE

Never turn o the power or disconnect the USB ash drive while the screen indicates “Executing...”

11. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Copying a Saved Song (Copy Song)

Songs that have been saved in Favorite (internal memory) can be copied to USB ash drive (sold separately). Alternatively, songs stored on a USB ash drive can be copied to Favorite.

* Audio les cannot be copied. * If a USB ash drive (sold separately) is not connected, you won’t

be able to perform this operation.

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Press the [ ] [ ] (Slow/Fast) button to choose “Copy

Song.”

3. Press the [Song] button.

The Copy Song screen will appear.

4. Use the [–] [+] buttons to select the copy-source and copy-

destination memory locations.

5. Press the [ ] (Fast) button.

Deleting a Saved Song (Delete Song)

Here’s how to delete a song that you saved on an Favorite (internal memory) or USB ash drive (sold separately).

MEMO

If you want to delete all songs that have been saved to Favorite, initialize the memory.

* If you want to delete a song on the USB ash drive (sold

separately), connect your USB ash drive to the USB memory port before you continue.

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Delete

Song.”

3. Press the [Song] button.

The Delete Song screen will appear.

4. Use the [–] [+] buttons to select the memory location that

contains the song you want to delete.

5. Press the [ ] (Fast) button.

Convenient Functions

Function Mode

Appendix

6. Press the [–] [+] button to select the song that you want

to copy.

Convenient Functions

6. Use the [–] [+] buttons to select the song that you want to

delete.

7. Press the [ ] (Fast) button.

A conrmation message will appear.

8. Press the [Song] button to delete the song.

If you decide not to delete, press the [ ] (Slow) button. Once the song is deleted, you’ll be returned to the screen you were

in at step 2.

NOTE

Never turn o the power or disconnect the USB ash drive while the screen indicates “Executing...”

9. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

Initializing the Memory (Format Media)

Here’s how you can completely erase all songs that were saved in Favorite (internal memory) or USB ash drive (sold separately).

NOTE

• Once an initialization is performed, all songs that have been saved in Favorite (internal memory) or USB ash drive will be erased. The erased data cannot be recovered, so we recommend that you check the contents of memory before you proceed.

• If you’re using new USB ash drive (sold separately) with the LX-15e for the rst time, you’ll need to initialize (format) the USB ash drive before using it. The LX-15e can’t use USB ash drive that has not been initialized.

6. Press the [Song] button to initialize the media.

If you decide not to initialize, press the [ ] (Slow) button. Once the initialization is nished, you’ll be returned to the screen

you were in at step 2.

7. Press the [Key Touch] button or the [Transpose] button to

nish the procedure.

Caution when initializing the memory

• Never turn o the power while “Executing...” is shown in the display.

• If the screen indicates “Error,” please refer to “Error Messages” (p. 57).

• Initializing the LX-15e’s Favorite will not initialize settings other than the contents of Favorite. If you want to return settings other than the contents of Favorite to their factoryset condition, execute the Factory Reset operation (p. 44).

• Don’t disconnect the USB ash drive until USB ash drive initialization has been completed.

Disabling the Buttons (Panel Lock)

When you activate Panel Lock, all buttons will be disabled. This prevents the tones or settings from being changed if you

inadvertently press a button.

1. Hold down the [AB Repeat] button until the upper right of

the display shows a “ ” symbol.

Panel Lock will be activated. All button operations will be disabled.

If you want to format USB ash drive, connect the USB ash drive to the USB memory port (p. 15).

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Use the [ ] [ ] (Slow/Fast) buttons to select “Format

Media.”

3. Press the [Song] button.

The Format Media screen will appear.

4. Use the [–] [+] buttons to select the memory that you

want to initialize.

5. Press the [ ] (Fast) button.

A conrmation message will appear.

2. To cancel Panel Lock, once again hold down the [AB

Repeat] button for a while.

Panel Lock will also be cancelled when you turn o the power.

* If you activate Panel Lock while a song is playing, playback will

stop.

* You can’t active Panel Lock during recording, while in Function

mode (p. 51), or during Tone Demo (p. 18).

Convenient Functions

Loading/Saving Piano Setups

The LX-15e lets you load a piano setup that you’ve saved on a USB ash drive, or save your piano setup to a USB ash drive.

MEMO

Only piano setups that were created on the LX-15e can be loaded.

Loading a Piano Setup

1. Connect your USB ash drive to the piano’s USB memory

port.

2. While holding down the [Key Touch] button, press the

[Transpose] button.

The [Key Touch] button and [Transpose] button will light; the LX-15e will be in Function mode.

3. Use the [ ] [ ] (Slow/Fast) buttons to choose “Piano

Setup Import.”

4. Press the [Song] button.

The Piano Setup Import screen will appear.

4. Press the [Song] button.

The Piano Setup Export screen will appear.

If you decide to cancel without saving the piano setup, press the [Metronome] button.

5. Use the [+] [-] buttons to specify the save-destination

number.

No piano setup has been saved in numbers whose piano setup name is shown as (Empty).

If you want to save by overwriting an unwanted piano setup, choose the unwanted piano setup number.

You can press the [ setup.

Use the [ ] [ ] (Slow/Fast) buttons to select the position at which to change the character.

Use the [+] [-] buttons to change the character.

] (Fast) button to edit the name of the piano

6. Press the [Song] button to save the piano setup to your

USB ash drive.

If you decide to cancel, press the [Metronome] button. When the piano setup has been saved, you will return to the screen

of step 3.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

If you decide to cancel without loading the piano setup, press the [Metronome] button.

5. Use the [+] [-] buttons to select the piano setup that you

want to load.

6. Press the [Song] button.

The piano setup will be loaded from the USB ash drive.

7. Press the [ ] (Fast) button.

When the piano setup has nished loading, you’ll return to the screen of step 3.

The loaded piano setup is automatically backed-up to memory. If you press the [

you’ll return to the screen of step 6.

] (Slow) button, loading will be cancelled and

8. Press the [Key Touch] button or the [Transpose] button to

exit Function mode.

Saving a Piano Setup

1. Connect your USB ash drive to the piano’s USB memory

port.

2. While holding down the [Key Touch] button, press the

[Transpose] button.

The [Key Touch] button and [Transpose] button will light; the LX-15e will be in Function mode.

3. Use the [ ] [ ] (Slow/Fast) buttons to choose “Piano

Setup Export.”

NOTE

Never turn o the power or disconnect the USB ash drive while the screen indicates “Executing...”

7. Press the [Key Touch] button or the [Transpose] button to

exit Function mode.

Items saved in the piano setup

Lid

Damper Resonance

Hammer Noise

Hammer Response

Duplex Scale

Dynamic Harmonic

String Resonance

Key O Resonance

Piano Designer settings

Other

Items automatically remembered by the LX-15e

Cabinet Resonance

Soundboard Behavior

Damper Noise

Master Tuning

Temperament

Temperament Key

Stretch Tuning

Note Volume

Note Character

Ambience (On/O, value)

Brilliance (value)

Key Touch (On/O, value)

Headphones 3D Ambience

Volume Limit

Volume (Speaker, headphones)

Convenient Functions

Function Mode

Appendix

Convenient Functions

About the Wireless LAN Function

By inserting the wireless USB Adapter (WNA1100-RL; sold separately) into the LX-15e’s USB MEMORY port, you’ll be able to use wireless-compatible applications (such as the “Piano Partner” iPad app).

iPad etc.

Items required to use the wireless LAN function

• Wireless USB Adapter (sold separately: WNA1100-RL)

• Wireless LAN access point (e.g., wireless LAN router) *1 *2 *3

• iPad etc.

*1 The wireless LAN access point you use must support WPS. If

*2 The ability to connect with all kinds of wireless LAN access

*3 If you’re unable to connect to the wireless LAN access point, try

*4 Depending on the wireless LAN system that you’re using,

*5 Depending on the wireless device used by the wireless LAN

*6 The sound and functionality might be temporarily aected

Wireless LAN access point

(e.g., wireless LAN router)

Wireless LAN Wireless LAN

your wireless LAN access point does not support WPS, you can connect using the procedure described in “Connecting to a Wireless LAN Access Point That You Select (Select AP)” (p. 49).

points is not guaranteed.

connecting using Ad-Hoc mode (p. 50).

you might be unable to connect, or the connection might be dropped.

function, noise might be heard from the LX-15e. In this case, you may be able to improve the situation by moving the wireless device away from the LX-15e, or by changing the wireless connection mode (basic WPS / Ad-Hoc mode).

while a connection is being established; this is not a malfunction.

LX-15e

Wireless USB Adapter (sold

separately: WNA1100-RL)

3. Press the [ ] [ ] (Slow/Fast) buttons to select the

“Wireless,” then press the [Song] button.

4. Press the [ ] [ ] (Slow/Fast) buttons to select the

“Connect,” then press the [Song] button.

5. Press the [ ] [ ] (Slow/Fast) buttons to select the “WPS,”

then press the [Song] button.

“Connect OK?” will appear.

6. Perform the WPS operation on your wireless LAN access

point (e.g., press the WPS button on your wireless LAN access point).

For details on WPS operation of your wireless LAN access point, refer to the documentation for your wireless LAN access point.

7. Press the [ ] (Fast) button of the LX-15e.

Once successfully connected, “Completed” will appear.

* If you fail to connect, refer to “Problems when connecting to a

wireless LAN” (p. 56).

8. Press the [Key Touch] or [Transpose] button to exit

Function mode.

NOTE

The device (e.g., iPad) running the app must be connected to the same network.

MEMO

• The connection data is stored in memory when you perform the WPS procedure; the device will automatically connect to the wireless network the next time.

• All connection data will be erased if you perform a factory reset.

This completes the procedure necessary for joining the wireless network. You can use the wireless connection from an iPad app such as Piano Partner.

Icons in the display

The wireless LAN status is shown in the lower left part of the display.

Basic Connection Method (Connect by WPS)

The rst time you connect the LX-15e to a wireless network, you’ll need to perform the following procedure (WPS) to join the wireless network.

This procedure is required only the rst time. (Once you’ve joined the network, this procedure will no longer be necessary.)

What is WPS?

This is a standard that makes it easy to make security settings when connecting to a wireless LAN access point. We recommend that you use WPS when connecting to a wireless LAN access point.

1. Insert the wireless USB Adapter (WNA1100-RL; sold

separately) into the LX-15e’s USB MEMORY port.

2. While holding down the [Key Touch] button, press the

[Transpose] button.

Icon Explanation

Currently connected to the wireless LAN access point. Three bars are used to indicate the signal level (the strength of the connected wireless LAN access point’s radio signal).

The wireless USB adapter is inserted, but not connected with a wireless LAN access point.

The wireless USB adapter is not inserted (nothing is displayed).

Ad-Hoc mode (p. 50).

Convenient Functions

Wireless LAN Function Settings

You can view or edit the wireless settings.

Basic Operation

1. While holding down the [Key Touch] button, press the

[Transpose] button.

2. Press the [ ] [ ] (Slow/Fast) buttons to select the

“Wireless,” then press the [Song] button.

3. Press the [ ] [ ] (Slow/Fast) buttons to select menu,

then press the [Song] button.

Menu Explanation

Status This shows the wireless LAN status.

Connect Connect to a wireless LAN access point.

Option Make settings for Wireless ID or Ad-Hoc mode (p. 50).

In the explanations in this chapter, procedures will be indicated using arrows, like this: “Wireless” g “Status.”

Status Indication

This shows the wireless LAN status.

1. Select “Wireless” g “Status.”

The status screen will appear.

Display Explanation

Currently connected to the wireless LAN access point.

Access Point

Now Connecting

Not Connected

Not Available The wireless USB adapter is not inserted.

Ad-Hoc SSID

Three bars are used to indicate the signal level (the strength of the connected wireless LAN access point’s radio signal). The identier (name) of the connected wireless LAN access point is shown.

A connection with the wireless LAN access point is being established.

The wireless USB adapter is inserted, but not connected to a wireless LAN access point.

Ad-Hoc mode (p. 50). The Ad-Hoc SSID is shown. Press the

] (Fast) button to display the Ad-Hoc key. For details,

[ refer to “Connecting in Ad-Hoc Mode” (p. 50).

Connecting to a Wireless LAN Access Point That You Select (Select AP)

This method lets you connect by choosing a wireless LAN access point from the list that is displayed.

* Wireless standards 802.11g/n (2.4 GHz) and authentication

methods WPA/WPA2 are supported.

1. Select “Wireless” g”Connect” g “Select AP,” then press the

[Song] button.

The Select Access Point screen will appear.

An “*” symbol is shown for the currently-connected wireless LAN access point.

2. Press the [–] [+] button to choose the wireless LAN access

point to which you want to connect, and press the [Song] button.

• You will be connected to the selected wireless LAN access point.

• If you’re using this wireless LAN access point for the rst time, you’ll proceed to the Passphrase screen.

• If this is a wireless LAN access point to which you have connected in the past, just press the [Song] button and you’ll be connected. Once successfully connected, “Completed” will appear.

Passphrase screen

3. Enter the security code (passphrase) of your wireless LAN

access point, and press the [Song] button.

How to enter characters

Use the [ which you want to specify a character. Use the [–] [+] buttons to change the character.

* You cannot enter a space at the end of the passphrase.

Once successfully connected, “Completed” will appear.

* If you fail to connect, refer to “Problems when connecting to a

wireless LAN” (p. 56).

4. Press the [Key Touch] or [Transpose] button to exit

Function mode.

] [ ] (Slow/Fast) buttons to select the position at

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

2. Press the [ ] (Fast) button to display the IP address.

Function Mode

Appendix

Convenient Functions

Other Settings (Option)

Make settings for Wireless ID or Ad-Hoc mode.

1. Select “Wireless” g “Option.”

2. Press the [ ] [ ] (Slow/Fast) buttons to select the

parameter that you want to change.

3. Press the [–] [+] button to edit the value of the setting.

Parameter Explanation

Species the nal digits of the Ad-Hoc SSID (LX-15) that will be shown as the instrument in the wirelessly connected app.

Normally, you should specify “0,” but if you have more than one of the same instrument, you can set the Wireless ID in

Wireless ID

Ad-Hoc Ch.

the range of 1–99 to change the device name and Ad-Hoc SSID for each instrument, as follows.

If Wireless ID=0, “LX-15” (default value) If Wireless ID=1, “LX-15_1”

If Wireless ID=99, “LX-15_99”

Species the channel (1–11) for Ad-Hoc mode. Normally, you won’t need to change the channel.

Try changing the channel only if you have problems connecting.

Connecting in Ad-Hoc Mode

Here’s how to connect in Ad-Hoc mode.

What is Ad-Hoc mode?

Ad-Hoc mode lets you connect the LX-15e directly to an iPad or other wireless device without using a wireless LAN access point. This is a convenient way to use the LX-15e with an iPad or other wireless device if you’re in a location where the wireless LAN access point you normally use is unavailable, such as when you’re away from home.

iPad etc.

LX-15e

’s device name and

LX-15e

1. Select “Wireless” g”Option” g “Ad-Hoc,” then press the

[Song] button.

2. Press the [ ] (Fast) button to turn the Ad-Hoc Mode “On.”

* To turn o Ad-Hoc Mode, press the [ ] (Slow) button.

3. Once in Ad-Hoc Mode, the Ad-Hoc SSID (LX-15) will be

displayed. Press the [ ] (Fast) button to display the Ad-Hoc key (a ve-character text string). Write down this number.

The Ad-Hoc key is the ve-digit number that’s displayed here. Each piano has its own unique number.

MEMO

• The Ad-Hoc SSID (LX-15) will be the value that you specied in the wireless options screen “Wireless ID” setting.

• The Ad-Hoc SSID and the Ad-Hoc key can also be veried in the status screen.

4. On the iPad or other wireless device that you want to

connect, select the Ad-Hoc SSID shown in the above screen to make the connection. (For example, on an iPad,

choose [Settings]

g [Wi-Fi] g [Choose a Network] to

select the above Ad-Hoc SSID (LX-15). A password entry screen will appear; enter the above Ad-Hoc key.)

For details on how to connect to a wireless LAN from an iPad or other device, refer to the owner’s manual of that device.

5. Press the [Key Touch] or [Transpose] button to exit

Function mode.

6. When you have nished the Ad-Hoc mode connection,

restore the iPad settings in [Settings] a Network] to their previous state.

g [Wi-Fi] g [Choose

Checking the MAC Address

Wireless USB Adapter (sold

Wireless LAN

Limitations

The iPad or other wireless device connected in Ad-Hoc mode will be unable to communicate with the Internet or with another wireless device. However, an iPad or other wireless device that has cellular capability will be able to connect to the Internet via the cellular connection.

Please be aware that if you use a cellular connection for Internet connectivity, you may incur costs depending on your rate plan.

separately: WNA1100-RL)

The MAC address indicated on the bottom of the wireless USB adapter (WNA1100-RL; sold separately).



Various Settings (Function Mode)

The same procedure is used for all settings in Function mode.

1. While holding down the [Key Touch] button, press the

[Transpose] button.

The [Key Touch] button and [Transpose] button will light; the LX-15e will be in Function mode.

Indication Value Explanation

Applying a Headphones 3D Ambience Eect to the Piano Sound (Headphones 3D Ambience)

Headphones 3D Ambience (*1)

You can apply a Headphones 3D Ambience eect which produces the sensation that the sound is emanating from the piano itself even when using headphones.

On Headphones 3D Ambience is on.

O Headphones 3D Ambience is o.

Adjusting the Dual Play Volume Balance (Dual Balance)

Dual Balance (*1)

When using Dual Play, you can adjust the volume balance between tone 1 and tone 2.

9-1 (tone 1 is louder)–9-9 (same volume)–1-9 (tone 2 is louder)

Matching the Pitch with Other Instruments (Master Tuning)

Master Tuning (*1)

When playing ensemble with other instruments and in other such instances, you can match the standard pitch to another instrument. The standard pitch generally refers to the pitch of the note that’s played when you nger the middle A key. For a cleaner ensemble sound while

performing with one or more other instruments, ensure that each instrument’s standard pitch is in tune with that of the other instruments. This tuning of all the instruments to a standard pitch is called “master tuning.”

415.3 Hz–440.0 Hz–466.2 Hz

2. Press the [ ] [ ] (Slow/Fast) buttons to select the

function setting that you want to change.

3. Press the [–] [+] button to edit the value of the setting.

4. Press the [Key Touch] button or the [Transpose] button to

exit Function mode.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Temperament (*1)

Temperament Key (*1)

Input Volume

Center Cancel

Changing the Tuning Method (Temperament)

variety of other tuning systems in existence. By playing in the temperament that was in use when a composition was created, you can experience the sonorities of chords originally intended for

that song.

REFERENCE

Equal, Just Major, Just Minor, Pythagorean, Kirnberger, Meantone, Werckmeister, Arabic

For details, refer to “Temperaments” (p. 43).

Specifying a Song’s Tonic (Temperament Key)

If you choose an equal temperament, there’s no need to select a temperament key.

C–B

Adjusting the Volume of an Audio Playback Device (Input Volume)

You can adjust the volume of an audio playback device that’s connected to the Input jack.

0–10

Playing Back an Audio File with Its Central Sound Minimized (Center Cancel)

You can minimize the playback of sounds located in the center of the sound eld (e.g., vocals or melody instruments) of the selected audio le or music from a digital audio player connected to the Input jack.

* For some songs, sounds located in the center might not disappear completely, or the tone quality of the sound might be aected.

MEMO

On Sound at center reduced during playback.

O Normal playback.

You can also turn the Center Cancel function on/o by pressing the [Right] button.

Convenient Functions

Function Mode

Audio Transpose

Transposing an Audio File (Audio Transpose)

The selected audio le and the sound of a digital audio player connected to the Input jack can both be transposed for playback.

* For some songs, an audio transpose setting other than 0 may aect the tone quality of the sound.

MEMO

-6–0–5(semitone units)

You can also change this setting by holding down the [Transpose] button and using the [–] [+] buttons.

Positive (+) values raise the pitch in semitone steps, and negative (-) values lower the pitch in semitone steps.

Appendix

Various Settings (Function Mode)

Indication Value Explanation

Specifying What the Transpose will Aect (Transpose Mode)

This setting species what the transpose will aect.

Transpose Mode (*1)

You can use the transpose to change the pitch of both the song and the keyboard, the pitch of only the song, or the pitch of only the keyboard.

Keyboard The sound of the keyboard

Song The song being played back and the sound being input via the Input jack

Keyboard & Song

The sound of the keyboard, the song being played back, and the sound being input via the Input jack

Changing the Pitch of the Tone in Octave Steps (Octave Shift)

Octave Shift

You can change the pitch of the Tone 2 in Dual Play (p. 19) and Lower tone in Split Play (p. 20) an octave at a time. Altering the pitch in one-octave units in this way is called “Octave Shift.”

For example, you can raise the pitch of the Lower Tone to the same pitch of the Upper Tone in Split Play.

-2–0–+2 (octave)

Selecting the Format for Recording (Recording Mode)

Recording Mode

You can choose whether to record as SMF or as audio.

MEMO

SMF SMF parts will be recorded separately. This allows you to re-record just a single part, or to overdub dierent parts.

Audio The recording will be made as audio data. The recorded song can be used in your computer.

You can also switch the recording mode by holding down the [ ] (Rec) button and using the [–] [+] buttons.

For details of the procedure on setting up the Function mode, refer to p. 51.

Damper Pedal Part (*1)

Center Pedal

Local Control

Changing How the Pedal Eects Are Applied (Damper Pedal Part)

When you press the damper pedal during Dual play or Split play, the pedal eect is normally applied to both tones, but you can also select the tone to which the eect is to be applied.

Right & Left All enabled

Right Applied only to the Tone 1 (in dual mode)/Right-hand Tone (in split mode)

Left Applied only to the Tone 2 (in dual mode)/Left-hand Tone (in split mode)

Changing How the Pedals Work (Center Pedal)

When you turn on the power, the center pedal functions as the sostenuto pedal (p. 14). You can change the function of the pedal to a variety of other operations.

Sostenuto Sets function to sostenuto pedal.

Play/Stop

Layer

Octave

The pedal will have the same function as the [

Pressing the pedal will layer on Tone 2, used for Dual play.

* The Layer function can be applied only when using Dual play.

Pressing the pedal will layer on a sound one octave higher.

* The Octave function cannot be applied while using Twin Piano, Dual play, or Split play.

] (Play/Stop) button.

Preventing Doubled Notes When Connected to a Sequencer (Local Control)

When you have a MIDI sequencer connected via USB, set this parameter to Local O. Since most sequencers have their Thru function turned on, notes you play on the

keyboard may be sounded in duplicate, or get dropped. To prevent this, you can enable the “Local O” setting so that the keyboard and internal sound generator will be disconnected.

Local Control

Sound Generator

USB MIDI In

USB MIDI Out

MIDI

Sequencer

MIDI Transmit Channel (*1)

Save Song

O

Local Control is on. The keyboard and composer are connected to the internal sound generator.

Local Control is o. The keyboard and composer are disconnected from the internal sound generator. Playing the keyboard will not produce sound.

MIDI Transmit Channel Settings (MIDI Transmit Channel)

This setting species the MIDI channel on which the LX-15e will transmit. MIDI uses sixteen “MIDI channels,” which are numbered 1 through 16. By connecting MIDI devices (USB MIDI) and specifying the appropriate MIDI channel for each device, you can play or select sounds on those devices.

The LX-15e will receive all sixteen channels (1–16).

O, 1–16

Renaming a Song (Save Song)

Here’s how to rename a song you’ve saved.

REFERENCE

For details, refer to “Renaming a Song” (p. 41).

For details of the procedure on setting up the Function mode, refer to p. 51.

Various Settings (Function Mode)

Indication Value Explanation

Copying a Saved Song (Copy Song)

Copy Song

A song you’ve saved to Favorite can be copied to a USB ash drive. Alternatively, a song saved to a USB ash drive can be copied to Favorite.

REFERENCE

For details, refer to “Copying a Saved Song (Copy Song)” (p. 45).

Deleting a Saved Song (Delete Song)

Delete Song

You can delete a saved song from Favorite or a USB ash drive.

REFERENCE

For details, refer to “Deleting a Saved Song (Delete Song)” (p. 45).

Initializing the Memory (Format Media)

Format Media

You can delete all songs from Favorite or a separately sold USB ash drive.

REFERENCE

For details, refer to “Initializing the Memory (Format Media)” (p. 46).

Changing the USB Driver Settings (USB Driver)

Normally, you don’t need to install a driver in order to connect the LX-15e to your computer. However, if some problem occurs, or if the performance is poor, using the Roland original driver may solve the problem. In this case setting “USB Driver” to “Original” on the LX-15e, install the driver on your personal computer. After changing this setting, you need to turn o the LX-15e, then turn it back on again.

USB Driver

MEMO

For details on downloading and installing the Roland original driver, refer to the Roland website. Roland website:

http://www.roland.com/

Generic

Original Choose this if you want to use a USB driver downloaded from the Roland website.

This setting is automatically saved in the LX-15e.

Choose this if you want to use the standard USB driver that was included with your computer. Normally, you should use this mode.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

USB Memory Mode

Visual Control Mode

Visual Control Channel (*1)

Wireless

Display Contrast

Changing the USB ash drive Setting (USB Memory Mode)

In some cases, when USB ash drive is connected to the USB memory port, it may take longer for data to be loaded, or data may fail to be loaded successfully. If this occurs, you may be able to solve the problem by changing the USB ash drive setting.

When the unit left the factory, this was set to “Mode 2” Normally, there is no need to make this setting.

MEMO

Mode 1, Mode 2

This setting is automatically saved in the LX-15e.

Controlling Video Equipment (Visual Control Mode)

Visual Control is a function that lets you control images along with your performance. If you’ve set Visual Control mode to MVC or V-LINK, playing the keyboard of LX-15e will control the images produced by the Visual Control device connected to LX-15e using a USB cable.

REFERENCE

O Visual Control is o.

MVC MIDI Visual Control mode is selected.

V-LINK V-LINK mode is selected.

For details of MVC, refer to “What is MIDI Visual Control?” (p. 54). And for details of V-LINK, refer to “What is V-LINK?” (p. 54).

Specifying the Visual Control Channel (Visual Control Channel)

Here’s how to specify the channel on which messages used to control video will be sent. (Visual Control Channel).

1–16 Species the MIDI channel used to transmit MIDI messages to the Visual Control device.

Wireless LAN Function Settings

You can view or edit the wireless settings (p. 48).

REFERENCE

For details, refer to “About the Wireless LAN Function” (p. 48).

Adjusting the Brightness of the Display (Display Contrast)

You can adjust the brightness of the LX-15e’s display.

REFERENCE

MEMO

For details, refer to “Adjusting the Brightness of the Display (Display Contrast)” (p. 44).

This setting is automatically saved in the LX-15e.

Convenient Functions

Function Mode

Appendix

MEMO

(*1) This parameter can be saved by the “Memory Backup” operation (p. 44).

Various Settings (Function Mode)

What is MIDI Visual Control?

MIDI Visual Control is an internationally-used recommended practice that was added to the MIDI specication so that visual expression could be linked with musical performance. Video equipment that is compatible with MIDI Visual Control can be connected to electronic musical instruments via MIDI in order to control video equipment in tandem with a performance.

What is V-LINK?

V-LINK is Roland’s proprietary specication that allows visual expression to be linked with musical performance. Video equipment that is compatible with V-LINK can be connected to electronic musical instruments, making it easy to enjoy a variety of visual eects that are linked with the performance.

Connection examples

Connect a USB cable from this unit’s USB port (p. 15) to the USB port of your Visual Control compatible device.

* You’ll need a commercially available USB cable in order to connect this unit to a device that supports Visual Control.

Visual control function chart

Playing the lowest 12 keys of this unit (A0–G#1) will transmit the following MIDI messages.

For details of the procedure on setting up the Function mode, refer to p. 51.

Visual Control function

Switch images

Indication Value Explanation

Transmitted MIDI message

CC 0 (Bank Select): 0–4 Play black keys

Program Change: 1–7 Play white keys

Specifying the Maximum Volume (Volume Limit)

Volume Limit (*1)

You can specify the maximum volume setting. This will prevent undesirably high volumes even if the [Volume] slider are operated unintentionally.

20, 40, 60 ,80, 100

Making the Power Automatically Turn O After a Time (Auto O)

Auto O

Piano Setup Import

Piano Setup Export

With the factory settings, the unit’s power will automatically be switched o 30 minutes after you stop playing or operating the unit. If you don’t want the power to turn o automatically, change the “Auto O” setting to “O” as follows.

REFERENCE

MEMO

For details, refer to “Making the Power Automatically Turn O After a Time (Auto O)” (p. 44).

This setting is automatically saved in the LX-15e.

Loading/Saving Piano Setups

The LX-15e lets you load a piano setup that you’ve saved on a USB ash drive, or save your piano setup to a USB ash drive.

REFERENCE

For details, refer to “Loading/Saving Piano Setups” (p. 47).

Storing Your Settings (Memory Backup)

Memory Backup

The LX-15e’s settings will return to their default settings when you turn o the power, but you can store these settings so that they will retain the changes you made even after the power is turned o, then on again.

REFERENCE

For details, refer to “Retaining the Settings Even After Power-o (Memory Backup)” (p. 44).

LX-15e’s operation

Factory Reset

MEMO

Restoring the Factory Settings (Factory Reset)

When you execute the “Factory Reset” function, the settings you’ve edited in Function mode will be restored to their factory-set state.

REFERENCE

(*1) This parameter can be saved by the “Memory Backup” operation (p. 44).

For details, refer to “Restoring the Factory Settings (Factory Reset)” (p. 44).



Troubleshooting

Symptom Cause/Action Page

Even though you’re using headphones and the sound is muted, a thumping sound is heard when you play the keyboard

Power turns o on its own

Power does not turn on

Screen display is irregular when power is turned on/o

Pedal does not work, or is “stuck”

Unable to read from/write to USB ash drive

“Buzz” is heard from external devices

The volume level of the instrument connected to Input jack is too low.

No sound

No sound when you play back a song

No sound from the leftmost notes of the keyboard

Notes don’t sound right

Sound is not loud enough Only the high sounds are heard

Pitch of the keyboard or song is incorrect

Not all the notes you play are sounded

Sounds are heard twice (doubled) when the keyboard is played

Eect does not apply

Reverberation remains even if You defeat the Ambience eect

LX-15e uses a hammer action keyboard in order to simulate an acoustic piano’s playing touch as realistically as possible. For this reason, you’ll hear the hammers thump when you play the keyboard, just as you would when playing an acoustic piano. Since this unit allows you to adjust its volume, you might notice the sound of the hammers in certain situations, but this does not indicate a malfunction. If vibration transmitted to the oor or walls is a concern, you may be able to minimize the vibration by moving the piano away from the wall, or by laying down a commercially available anti-vibration mat designed for use with pianos.

When 30 minutes have elapsed since you last played or operated this unit, the power will turn o automatically. (This is the factory setting).

If you don’t need the power to turn o automatically, turn the “Auto O” setting “O.” Is the power cord connected correctly? p. 63 Could you have turned the power on again immediately after turning the power o?

Allow an interval of at least ve seconds before turning the power on again. Since the LX-15e uses a liquid-crystal display, you may nd that it is unable to display letters or other things in environments

where temperatures go below 0 degrees Celsius (32 degrees Fahrenheit). Is the pedal connected correctly? Plug the cable rmly into the pedal connector. If you disconnect the pedal cord from the LX-15e while the power is on, the pedal eect may remain “stuck” in the On condition. You must power-o the LX-15e before connecting or disconnecting the pedal cord. Could you have changed how the pedal eect is applied? If the damper pedal part is set to Right, the pedal will apply only to the right tone; if it is set to Left, the pedal will apply only to

the left tone. Could Twin Piano be turned on? If Twin Piano is on, the right pedal will aect only the right-hand keyboard zone and the left pedal will aect only the left-hand

keyboard zone. Could you have changed the function of the pedal? If you’ve reassigned the function of the center pedal, this pedal will not operate as the sostenuto pedal. Are you using (optional) Roland USB ash drive? Reliable performance cannot be guaranteed if you use non-Roland USB ash drive products. If you are unable to read or write USB ash drive successfully, change the USB memory mode. p. 53 Are the external devices connected to more than one AC power outlet? If you connect external devices, be sure to connect them to the same AC outlet. Could the Input volume be set to “0”? p. 51 Raise the volume of the connected device. – Could you be using a connection cable that contains a resistor? Use a connection cable that does not contain a resistor.

Is the speaker cable connected correctly? p. 63 Could the LX-15e’s volume or the volume of the connected equipment be turned down? p. 17 Could headphones be connected?

Could there be a plug inserted in a headphone jack? The speakers will not produce sound if headphones or plug are connected to the headphone jacks. Has Local Control been set to “O”? When Local Control is set to O, no sound is produced by playing the keyboard. Set Local Control to On. Could Twin Piano mode be set to “Individual”? If headphones are connected when Twin Piano is “On” and the mode is set to “Individual,” notes played in the left-hand keyboard

zone will not be heard from the headphones connected to the right Phones jack. Similarly, notes played in the right-hand keyboard zone will not be heard from the headphones connected to the left Phones jack.

Has Local Control been set to “O”? When Local Control is set to O, no sound is produced by playing the song. Set Local Control to On.

Could the song volume be set to “0”? p. 29 Could the Visual Control mode be set to MVC or V-LINK? If the Visual Control mode is set to MVC or V-LINK, the lowest 12 keys of the keyboard (A0–G#1) are used to control images; they

will not produce sound.

Is the speaker cable connected correctly? p. 63

Could you have made Transpose settings?

Is the Master Tune setting appropriate? p. 43 Is the setting for the Temperament correct? p. 43 Is the settings for the Stretch Tuning correct? p. 43 The maximum simultaneous polyphony is 128 voices. If you are playing along with a song and making heavy use of the damper

pedal, the number of notes the LX-15e is attempting to produce may exceed the maximum polyphony, meaning that some of the notes will drop out.

Is the LX-15e in Dual play? p. 19 When the LX-15e is connected to an external sequencer, set the Local Control to o. Alternatively, the sequencer could be set so

its Soft Thru feature is O. When you are using Dual play or Split play, and dierent eects are specied for the two selected tones, the eect will not be

applied to Tone 2 (when using Dual play) or the left-hand tone (when using Split play). The LX-15e’s piano sound faithfully simulates the depth and resonance of an acoustic piano, and this may give the impression of

reverberation even if you’ve defeated the Ambience eect. Also, you may be able to eliminate some reverberation by reducing the value set for “Cabinet Resonance.”

p. 44

p. 63

p. 52

p. 24

p. 52

p. 15

p. 52

p. 24

p. 52

p. 53

p. 25 p. 39

p. 52

p. 43

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

–

Convenient Functions

Function Mode

–

Appendix

–

Troubleshooting

Symptom Cause/Action Page

The sound of the higher notes suddenly changes from a certain key

High-pitched ringing is heard

Low notes sound wrong, or are buzzy

Song does not play correctly

Only the sound of a particular instrument in a song does not play

Sound is heard from a muted part

Song volume is low / Volume diers between recording and playback

Can’t play back a song saved in USB ash drive

Song tempo becomes unstable When playing a song from USB ash drive, the tempo may become unstable if there is an excessive amount of performance data. –

Song name in USB ash drive is not shown

Can’t record / play back Can’t record SMF Has one of the part buttons for recording been selected? p. 32 Can’t record audio Is a USB ash drive connected to the USB memory port? –

Tone quality of the piano sound changes when you record a performance as audio

The recorded performance disappeared

Problems when connecting to a wireless LAN

Can’t connect to a wireless LAN access point

On an acoustic piano, the approximately one and a half octaves of notes at the top of the keyboard will continue sounding regardless of the damper pedal. These notes also have a somewhat dierent tonal character. LX-15e faithfully simulate this characteristic of acoustic pianos. On the LX-15e, the range that is unaected by the damper pedal will change according to the key transpose setting.

Is the speaker cable connected correctly? p. 63

If you hear this in headphones:

Piano sounds that have a brilliant and crisp character contain substantial high-frequency components that may sound as though a metallic ringing has been added. This is because the character of an actual piano is being faithfully reproduced, and is not a malfunction.

This sound can be adjusted by modifying the following settings.

• String Resonance (p. 42)

• Ambience (p. 22)

• Duplex Scale (p. 42).

If you don’t hear this in headphones:

It is likely that there is some other reason (such as resonances within the unit). Please contact your dealer or a nearby Roland service center.

If you don’t hear this in headphones:

Performing at high volumes may cause the speakers or objects near the LX-15e to resonate. Fluorescent lights or glass doors may also resonate sympathetically. In particular, this is more likely to occur for lower notes and higher volumes. You can take the following measures to minimize resonances.

• Locate the speakers 10–15 cm (4–6 inch) away from walls or other surfaces.

• Keep the volume down.

• Move away from the objects that are resonating.

If you hear this in headphones:

It is likely that there is some other reason. Please contact your dealer or a nearby Roland service center.

Could a part be muted? If the button indicator is out, the music on that part is not heard. Press the part button so the indicator is illuminated.

Could the part mute volume be set to other than “0”? If you set this to “0,” the sound of a muted part will be completely inaudible.

Could the Song Balance be lowered? p. 29

Could the Audio les of the format be played? Audio les of the following format can be played back.

• File extension “.WAV”

• 16-bit linear

• “44.1 kHz” sampling rate Is the lename extension “MID”? Files with other lename extensions cannot be handled as song data.

The song name will not be shown if the song information in the le is empty or consists only of spaces. – Is the lename extension “MID”?

Files with other lename extensions cannot be handled as song data.

Thanks to its multiple number of speakers, each of which can be used to play a dierent portion of the overall sound, the LX-15e is capable of producing piano sounds that possess great depth and seem to have three-dimensional presence.

Such eects are produced when you play something on the keyboard, or when you play back a song that's been recorded as an SMF. However, when you make an audio recording, the song will consist of two channels (stereo), and such eects cannot be reproduced.

Your recorded performance will disappear if you switch o the LX-15e’s power or select a song. There is no way to recover the lost performance. Before you turn o the power, save your recorded performance in Favorite or

USB ash drive.

• Make sure that your wireless LAN access point supports WPS. If your wireless LAN access point does not support WPS, you can connect using the procedure described in “Connecting to a Wireless LAN Access Point That You Select (Select AP)” (p. 49).

• The 802.11a/b wireless standard is not supported. Please use the 802.11g/n (2.4 GHz) wireless standard.

• The WEP authentication method is not supported. Please use the WPA or WPA2 authentication method.

• Make sure that DHCP is enabled for your wireless LAN access point.

• If you don’t get connected to the previously-connected wireless LAN access point when you turn on the unit, check and make sure the setting described in “Connecting in Ad-Hoc Mode” (p. 50) is OFF.

• The connection might not occur successfully due to the state of the radio signal. If so, use the procedure described in “Connecting to a Wireless LAN Access Point That You Select (Select AP)” (p. 49), and select your wireless LAN access point and reconnect.

• There is a limit to the connection data that can be remembered. Making a new connection may cause older connection data to be deleted. All connection data will be deleted if you execute a factory reset. If the connection data has been deleted, please re-connect to the wireless LAN access point.

p. 48–p. 50

–

p. 30

–

Troubleshooting

Symptom Cause/Action Page

The display indicates “Error 46,” and can’t connect to the wireless LAN access point

Communication is unstable

The LX-15e is not found in the instrument connections of the app (such as the iPad app Piano Partner)

Your iPad won’t connect to the Internet

Limitations regarding audio les

• Ambience will not be applied to audio les (p. 22).

• Audio data cannot be saved in the unit’s internal memory. In order to record audio, you must connect a USB ash drive (separately sold) (p. 33, p. 37, p. 38)

• The Part Mute function cannot be used when playing audio les (p. 30)

• Audio les cannot be copied (p. 45)

• This Access Point is not supported. Please use the WPA or WPA2 authentication method.

Communication may be unstable depending on the usage of the radio frequency spectrum. If communication is unstable, the response may be sluggish, or if using audio communication, there may be dropouts in the

audio. The following actions may improve the situation.

• Move the wireless LAN access point and the LX-15e closer to each other.

• Change the channel setting of the wireless LAN access point.

• Is the LX-15e powered up?

• Is the wireless USB adapter (WNA1100-RL) inserted to the LX-15e?

• Is the LX-15e connected to the wireless LAN?

• Are the LX-15e and the iPad connected to the same network (the same wireless LAN access point)?

• Is the wireless LAN access point set to allow communication between wireless LAN devices? For details on settings, refer to the owner’s manual of your wireless LAN access point.

• Is the wireless LAN access point connected to the Internet?

• Could you be connected in Ad-Hoc mode? The iPad or other wireless device connected in Ad-Hoc mode will be unable to communicate with the Internet or with another wireless device. However, an iPad or other wireless device that has cellular capability will be able to connect to the Internet via the cellular connection. Please be aware that if you use a cellular connection for Internet connectivity, you may incur costs depending on your rate plan.

p. 48–p. 50

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer



Error Messages

Indication Meaning

Error 1 You can only read the music le. It can not be saved.

Error 2

Error 10 No external media is inserted. Insert the external media and try again.

Error 11

Error 14

Error 15 The le is unreadable. The data format is not compatible with the LX-15e.

Error 16

Error 18

Error 30 Internal memory capacity of the LX-15e is full.

Error 40

Error 43 A MIDI transmission error has occurred. Check the connected USB MIDI device. Error 46 This Access Point is not supported. Please use the WPA or WPA2 authentication method (p. 48–p. 50).

Error 51

Error 65

* External Media: USB ash drive

An error occurred during writing. The external media may be corrupted. Insert other external media and try again. Alternatively, you can initialize the external media. The external media’s protect tab may be in the “Protect” (writing prohibited) position may not yet be initialized.

There is not sucient free memory in the save destination. Either insert other external media or delete unneeded les and try again. An error occurred during reading. The external media may be corrupted. Insert other external media and try again. Alternatively, you can initialize the external media.

Data was not called up in time for playback of the song. After waiting several seconds, you may be able to play back the song by pressing the [ (Play/Stop) button again.

This audio format is not supported. Please use 44.1 kHz 16-bit linear WAV format audio les.

The LX-15e cannot deal with the excessive MIDI data sent from the USB MIDI. Reduce the amount of MIDI data sent to the LX-15e.

There may be a problem with the system. Repeat the procedure from the beginning. If it is not solved after you have tried several times, contact the Roland service center.

The USB ash drive connector was subjected to excessive current. Make sure that there is no problem with the external media, then turn the power o, then on again.

Convenient Functions

]

Function Mode

Appendix



Tone List

Piano–Grand

No. Tone Name Explanation

1 ConcertPiano

2 BalladePiano A mellow grand piano sound, recommended for quiet songs.

3 Bright Piano A brilliant grand piano sound, recommended when you want the piano to stand out in an ensemble.

4 MagicalPiano A charming sound that layers synth bells with Concert Piano.

5 Piano + Str. Strings layered with Concert Piano.

6 Piano + Pad A pad layered with Concert Piano.

7 Piano+Choir A choir layered with Concert Piano.

8 Pure Piano A grand piano sound notable for its clarity. When using headphones, this will sound the same as the Concert Piano.

9 Fortepiano An early type of piano with a distinctive sound that’s somewhat dierent than today’s pianos.

10 Mellow Forte A mellow FortePno (Forte Piano) sound.

11 Bright Forte A brilliant FortePno (Forte Piano) sound.

12 Dolcechord A dream-like sound that can sound like a piano or a harpsichord.

13 Harpsichord A type of keyboard instrument widely used in Baroque music, producing a delicate sound.

14 Harpsi 8'+4' The sound of a harpsichord layered with sound an higher octave.

The sound of a splendid concert grand piano. This piano sound has our highest recommendation, and can be used for any style of music.

Piano–Upright

No. Tone Name Explanation

1 UprightPiano The sound of an upright piano. The sound will feel closer to you.

2 MellowUprght A mellow upright piano sound.

3 BrightUprght A brilliant upright piano sound.

4 Rock Piano A robust piano sound, recommended for boogie-woogie playing.

5 RagtimePiano A honky-tonk piano sound, recommended for ragtime playing.

E. Piano

No. Tone Name

1 Tremolo EP

2 Pop E.Piano

3 Vintage EP

4 FM E.Piano

5 EP Belle

6 '60s E.Piano

7 Clav.

8 Stage Phaser

9 '70s E.Piano

10 E.Grand

Strings

No. Tone Name

1 SymphonicStr

2 Epic Strings

3 Rich Strings

4 OrchestraStr

5 Orchestra

6 ChamberWinds

7 Harp

8 Violin

9 Velo Strings

10 Flute

11 Cello

12 OrchestraBrs

13 PizzicatoStr

14 DecayStrings *

* Tones indicated by “*” are suitable for

playing layered with a piano tone.

Other

No. Tone Name

1 Vibraphone

2 Celesta

3 Jazz Scat

4 SymphonicCho

5 Pipe Organ

6 Nason t 8'

7 Combo Jz.Org

8 Ballad Organ

9 Soft Pad

10 Harpvox

11 Nylon-str.Gt

12 Steel-str.Gt

13 Marimba

14 Mallet Isle

15 Morning Lite

16 Ballad Bells

17 Accordion

18 ChurchOrgan1

19 ChurchOrgan2

20 Aerial Choir

21 Angels Choir

22 Beauty Vox

23 Female Aahs

24 Male Aahs

25 Decay Choir *

No. Tone Name

26 Thum Voice

27 Gospel Spin

28 Full Stops

29 Mellow Bars

30 Light Organ

31 Lower Organ

32 '60s Organ

33 Glass Pad

34 Lunar Strngs

35 Dcy ChoirPad *

36 Jazz Guitar

37 AcousticBass

38 A.Bass+Cymbl

39 FingeredBass

40 BrassSection

41 Alto Sax

42 Tenor Sax

* Tones numbered 43 and higher are

accompaniment-use GM2 tones.

* In the tone group “Other” when you

hold down the [–] [+] buttons to switch tone in succession, the tones will stop changing at number 43 and number

52.

* To select the next sound, release the [–]

[+] buttons, then press it again.



Internal Song List

No. Song Title Composer

MASTERPIECE

The Nutcracker "Danse des

Mirlitons"

The Marriage of Figaro

"Overture"

3 Barcarolle Fryderyk Franciszek Chopin

4 Zhavoronok

5 Floral Pursuits * Léo Delibes, Arranged by John Maul

6 Sonate für Klavier Nr.23 1 Ludwig van Beethoven

7 Sonate für Klavier Nr.23 2 Ludwig van Beethoven

8 Sonate für Klavier Nr.23 3 Ludwig van Beethoven

9 Valse, op.34-1 Fryderyk Franciszek Chopin

10 Polonaise op.53 Fryderyk Franciszek Chopin

11 Nocturne No.20 Fryderyk Franciszek Chopin

12 Die Forelle

13 Reets dans l'Eau Claude Achille Debussy

14 La Fille aux Cheveux de Lin Claude Achille Debussy

15 La Campanella Franz Liszt

16 Scherzo No.2 Fryderyk Franciszek Chopin

17 Étude, op.10-12 Fryderyk Franciszek Chopin

18 Sonate No.15 Wolfgang Amadeus Mozart

19 Liebesträume 3 Franz Liszt

20 Étude, op.10-3 Fryderyk Franciszek Chopin

21 Je te veux Erik Satie

22 Valse, op.64-1 Fryderyk Franciszek Chopin

23 Golliwog's Cakewalk Claude Achille Debussy

24 Fantaisie-Impromptu Fryderyk Franciszek Chopin

25 Arabesque 1 Claude Achille Debussy

26 An der schönen, blauen Donau Johann Strauss, Sohn

27 Auf Flügeln des Gesanges Felix Mendelssohn

28 Mazurka No.5 Fryderyk Franciszek Chopin

29 Gymnopédie 1 Erik Satie

30 Étude, op.25-1 Fryderyk Franciszek Chopin

31 Clair de Lune Claude Achille Debussy

32 Étude, op.10-5 Fryderyk Franciszek Chopin

33 Dr. Gradus ad Parnassum Claude Achille Debussy

34 Grande Valse Brillante Fryderyk Franciszek Chopin

35 La prière d'une Vierge Tekla Badarzewska

36 Course en Troïka Peter Ilyich Tchaikovsky

37 To The Spring Edvard Hagerup Grieg

38 Valse, op.64-2 Fryderyk Franciszek Chopin

39 Radetzky Marsch Johann Baptist Strauss

40 Träumerei Robert Alexander Schumann

41 Moments Musicaux 3 Franz Peter Schubert

42 Prélude, op.28-15 Fryderyk Franciszek Chopin

43 Harmonious Blacksmith Georg Friedrich Händel

44 Ungarische Tänze 5 Johannes Brahms

45 Türkischer Marsch Ludwig van Beethoven

46 Nocturne No.2 Fryderyk Franciszek Chopin

47 Frühlingslied Felix Mendelssohn

48 Präludium Johann Sebastian Bach

49 Jägerlied Felix Mendelssohn

50 Passepied Claude Achille Debussy

51 Für Elise Ludwig van Beethoven

52 Türkischer Marsch Wolfgang Amadeus Mozart

53 Ständchen Franz Peter Schubert

Peter Ilyich Tchaikovsky

Wolfgang Amadeus Mozart

Mikhail Ivanovich Glinka, Arranged by Mily Alexeyevich Balakirev

Franz Peter Schubert, Arranged by Franz Liszt

No. Song Title Composer

54 Humoreske Antonín Dvořák

55 Blumenlied Gustav Lange

56 Alpenglöckchen Theodor Oesten

57 Menuett G dur Ludwig van Beethoven

58 Venezianisches Gondellied Felix Mendelssohn

59 Alpenabendröte Theodor Oesten

60 Farewell to the Piano Ludwig van Beethoven

61 Brautchor Wilhelm Richard Wagner

62 Forget-Me-Not Heinrich Lichner

63 Wiener Marsch Carl Czerny

64 Le Coucou Louis Claude Daquin

65 Menuett G dur Johann Sebastian Bach

66 Spinnerlied Albert Ellmenreich

67 Gavotte François Joseph Gossec

68 Heidenröslein Gustav Lange

69 Zigeuner Tanz Heinrich Lichner

70 La Cinquantaine Gabriel Marie

71 Csikos Post Hermann Necke

72 Dolly's Dreaming Awakening Theodor Oesten

73 La Violette Louis Streabbog

74 Fröhlicher Landmann Robert Alexander Schumann

75 Sonatine op.36-1 Muzio Clementi

76 Sonatine op.20-1 Friedrich Kuhlau

77 Sonatine No.5 Ludwig van Beethoven

SELECTIONS

1 Triumphal March from Aida Giuseppe Verdi

2 Ninna Nanna Johannes Brahms

3 Papageno’s Aria Wolfgang Amadeus Mozart

4 The Spring Antonio Lucio Vivaldi

5 Polovtsian Dances Alexander Borodin

6 Air on the G String Johann Sebastian Bach

7 Cucaracha Mexican Popular Song

8 Samba Lelè Brazilian Popular Child Song

9 Old MacDonald Had a Farm Popular Child Song

10 When the Saints Go Marching in Popular Song

CZERNY 100

1 –100 Czerny 100 Carl Czerny

HANON

1 –20 Hanon 1–20 Charles Hanon

private, personal enjoyment is a violation of applicable laws. * No data for the music that is played will be output from USB Computer port. * The copyrights to the songs marked by an asterisk “*” are owned by the Roland

Corporation. * MASTERPIECE 3–4, 6–17 are piano solos. They have no accompaniment.

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Function Mode

Appendix



Main Specications

Roland LX-15e: Digital Piano

Keyboard

Touch Sensitivity

Keyboard Mode

Pedals

Sound Generator Piano Sound SuperNATURAL Piano Sound MIDI Format Conforms to GM2, GS, XGlite Max. Polyphony 128 voices

Tones

Temperaments 8 types, selectable temperament key

Individual Note Voicing (adjustable in individual notes)

Master Tuning 415.3–466.2 Hz (adjustable in increments of 0.1 Hz)

Transpose

Eects

Metronome Tempo Quarter note = 10–500 Beat 2/2, 0/4, 2/4, 3/4, 4/4, 5/4, 6/4, 7/4, 3/8, 6/8, 9/8, 12/8 Volume 11 levels

SMF Recorder Parts 3 parts Save Song Standard MIDI Files (Format 0) Note Storage Approx. 30,000 notes

Controls

Tempo Quarter note = 10–500 Resolution 120 ticks per quar ter note

Audio Playback File Format: Audio File (WAV 44.1 kHz, 16-bit linear format)

Recording

Transpose

Playback Speed 75–125%

Controls

88 keys (PHA-4 Concert Keyboard: with Escapement and Ebony/ Ivory Feel)

Key Touch: 100 types, xed touch Hammer Response: O, 10 levels

Whole Dual (volume balance adjustable) Split (split point adjustable) Twin Piano

Damper (Progressive Damper Action Pedal, capable of continuous detection)

Soft (capable of continuous detection) Sostenuto (function assignable)

Grand Piano: 14 Tones Upright Piano: 5 Tones E. Piano: 10 Tones Strings: 14 Tones Other: 307 Tones (including 8 drum sets, 1 SFX set)

Stretched Tuning: -50.0–+50.0 cent Note Volume: -50–0 Note Character: -5–+5

Key Transpose: -6–+5 (in semitones) Playback Transpose: -6–+5 (in semitones, including audio les)

Ambience (O, 10 levels) Brilliance (O, 21 levels)

Only for Piano Tones (Piano Designer):

Open/close lid (7 levels) Hammer Response (O, 10 levels) Hammer Noise (5 levels) Damper Noise (O, 10 levels) Damper Resonance (O, 10 levels) String Resonance (O, 10 levels) Key O Resonance (O, 10 levels) Cabinet Resonance (O, 10 levels) Duplex Scale (O, 10 levels) Dynamic Harmonic (O, 10 levels) Soundboard Behavior (O, 10 levels)

Only for Organ Tones:

Rotary Speaker Eect (Slow/Fast)

Song Select, Play/Stop, Rec, Rewinding, Fast-forwarding, Top of song, Part Mute, Mute Volume, Tempo, Tempo Mute, All Songs Play, Count-in, Song Balance, AB Repeat

Keyboard, SMF data, Audio from Input jack File Format: Audio File (WAV 44.1 kHz, 16-bit linear format)

Playback Transpose: -6–+5 (in semitones, including audio from Input jack)

Song Select, Play/Stop, Rec, Rewinding, Fast-forwarding, Top of song, Playback Speed, All Songs Play, Song Balance, AB Repeat, Center Cancel (with Audio from Input jack)

Internal Memory Save Song Standard MIDI Files (Format 0) Songs Max. 99 songs

External Memory External Storage USB Flash Memory

Playable Software

Save Song

Other

Internal Songs

Display

Language English Music Rest Full score music rack (Width: 1,285 mm) Keyboard Lid Soft-fall fallboard

Other Functions

Connectors

Rated Power Output

Volume Level (SPL)

Speakers

Headphones Eects: Headphones 3D Ambience

Control

Power Consumption

Dimensions (including piano stand)

Weight (including piano stand)

Accessories

Options (sold separately)

Standard MIDI Files (Format 0, 1) Roland Original Format (i-Format) Audio File (WAV, 44.1 kHz, 16-bit linear format)

Standard MIDI Files (Format 0) Audio File (WAV, 44.1 kHz, 16-bit linear format)

Piano Masterpieces: 77 songs Selection: EU= 10 songs/ US= 18 songs/ Other= 10 songs Hanon: 20 songs Czerny #100: 100 songs

Graphic LCD 122 x 32 dots (Contrast 10 levels) Beat Indicator

Wireless Connect (when using optional Wireless USB Adapter) Panel Lock Auto O V-LINK MIDI Visual Control Demo

AC inlet Input jack: Stereo miniature phone type Output (L/Mono, R) jacks: 1/4-inch phone type USB COMPUTER port: USB Type B USB MEMORY port: USB Type A Phones jacks (Stereo, with Twin Piano Individual Mode) x 2: Stereo miniature phone type, Stereo 1/4-inch phone type

60 W x 2 20 W x 2

112 dB

* This value was measured according to the method that is

based on Roland’s technical standard.

Cabinet Speakers: 16 cm (6-5/16 inches) x 2 Near-eld Speakers: 5 cm (2 inches) x 2 Spatial Speakers: (12 cm (4-3/4 inches) x 8 cm (3-3/16 inches)) x 2

Volume (Slider, with the speaker volume and the headphones volume automatically select function, with the volume limit function)

38 W (36–85 W)

38 W: Average power consumption while piano is played

with volume at center position

36 W: Power consumption immediately after power-up;

nothing being played

85 W: Rated power consumption

(with top lid close) 1,408 (W) x 472 (D) x 1,070 (H) mm 55-7/16 (W) x 18-5/8 (D) x 42-1/8 (H) inches

(with top lid open) 1,408 (W) x 483 (D) x 1,128 (H) mm 55-7/16 (W) x 19-1/16 (D) x 44-7/16 (H) inches

91 kg/200 lbs 10 oz

Owner’s manual Assembly manual (*1) Power cord Headphone hook Screw set (*1) *1 Supplied with the stand.

Headphones USB Flash Memory (*2) Wireless USB Adapter (*2) Audio Cable *2 Use USB Flash Memory and Wireless USB Adapter sold by Roland. We cannot guarantee operation if other products are used.

* In the interest of product improvement, the specications and/

or appearance of this unit are subject to change without prior notice.

MEMO

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Function Mode

Appendix



Assembling the LX-15

* To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly. Please keep these instructions close at hand, so you can refer to

* 5 1 0 0 0 2 1 6 0 2 - 0 1 *



Assembling

them whenever you need. * To move the piano, lift it carefully—all the while keeping it level. * Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet. * Make sure to enlist the help of at least one other person when assembling this unit and moving it to a di erent location. * Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won’t accidentally get swallowed. * The screwdriver needed to perform the assembly is not supplied. You’ll need to have ready a Phillips screwdriver that matches the size of the screws. * All screws should be tightened provisionally  rst, then tightened later. To tighten a screw provisionally, screw it in until about half of its length is no longer visible. Do not use an

electric screwdriver when tightly securing the screws. Otherwise, you risk stripping the threads. * After  rmly tightening all the screws, place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk

causing damage to the pedals due to instability and unnecessary movement. * The piano unit and the surface of the stand are very delicate; handle with care to avoid scratching them. * Do not place the piano unit directly on the  oor. Doing so will damage the bottom panel case and the connectors and holders on the bottom of the piano.

Parts Check

Side Board (left)

Side Board (right)

Pedal Board

Front Board

Speaker Box

Rear Board

* You will also need to have Phillips screwdrivers (size: #2, #3). * When handling the side boards, avoid touching the metal portions marked with in the  gure.

1. Assembly Procedure

* At  rst, assemble the entire stand in a temporary fashion, without really

tightening the screws. Then, after checking the overall alignment of the boards (and gently shifting certain parts where necessary), go around and tightly fasten each of the screws.

* If necessary, spread out a blanket or similar material to prevent the stand or  oor

from being scratched during assembly.

* Be careful not to pinch the pedal cord during assembly.

1. As shown in the illustration, place the left and right side

boards on the pedal board so that the metal brackets are on the inside, and fasten them provisionally using screws (M6 x 40 mm).

2. After you have provisionally tightened screws

locations), use a screwdriver to tighten them  rmly.

* When attaching the pedal board, do not allow any gap to remain between the

side board and pedal board when the pieces are assembled.

As seen from the bottom

Screw A x 2

(four

Screw (M6 × 40 mm) x 4

Screw (M5 × 20 mm) x 10

Thumbscrew x 4 (two of them are already attached to the unit)

Screw (M4 × 16 mm) x 2

Headphone Hook x 1

4. Loosen the screws attached to the left and right side boards

approximately three turns, so that they protrude about 3 mm, as shown in the illustration.

Space

3 mm

5. Hook the metal brackets of the front board over the screws

you loosened, as shown in the illustration.

6. Use four screws

pedal board.

Rear view

(M5 x 20 mm) to provisionally fasten the

Leave the pedal cord extended.

3. With the help of another person, raise the left and right side

boards to an upright position.

* Take care that the pedal boards are not twisted.

Screws you loosened in step 4 (two screws)

Screws B x 4

7. Securely tighten the two side board screws and four pedal

board screws.

* When attaching the front board, before tightening the screws, adjust things as

necessary at all the points where there are screws so as to assure that the front board is aligned in parallel with the pedal board.

8. Set the speaker box so that the speaker cable is above it, and

align the holes in the metal parts on the inner side of the side boards with the holes in the speaker box.

9. Attach the speaker box to the metal parts on the inside of

the side boards from underneath using screws mm). Then fasten the rear with screws

well.

Rear view

Screws

x 4

(M5 x 20

(M5 x 20 mm) as

4. Loosen the two thumbscrews

that are attached at the locations shown in the  gure. As illustrated, you should create gaps that are about 10 mm in size.

Rear view

Space 10 mm

5. Attach the rear board by hooking it onto the gaps left by the

screws, as shown in the  gure.

Thumbscrew

Holder

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

2. Install the Piano onto the Stand

1. Align the two screws at the bottom of the piano (one each

at left and right) with the metal  xtures on the side boards, then while slightly lifting the front end of the piano, push it toward the rear, while making sure that the screws have been properly grasped by the metal  xtures.

* When handling the piano,  rmly grasp it. Be careful, so you do not get your

 ngers pinched.

2. Fasten the piano to the stand with the screw

Screw

Screw B x 2

Please don’t get your  ngers pinched.

3. Connect the speaker cable to the speaker connector on the

bottom of the main unit, connect the power cord to the AC In connector on the bottom of the main unit, and connect the pedal cord to the Pedal jack.

(M5×20 mm).



Pedal cord

Power

cord

6. Use two of the thumbscrews

Thumbscrew

x 2

7. Securely tighten the thumbscrews

in step 4, as well as the thumbscrews

to fasten the rear board.

that were loosened

that were used to

fasten the rear board in step 6.

* The screws can be more securely tightened if you raise the rear board

slightly.

8. Fasten the headphone hook using screws

(M4 x 16 mm).

Screw D x 2

3. Adjusting the Adjuster

Turn the adjuster to lower it until the adjuster is in  rm contact with the  oor. In particular, when you’ve placed the piano on carpet, you must turn the adjuster until it is pressing  rmly against the  oor.

Convenient Functions

Speaker cable

Adjuster

* The pedal may be damaged if there is a gap between the adjuster and the  oor.

When Moving the Piano

When you need to move the unit, you should  rst close the keyboard cover, close the lid, detach the power cord, and raise the adjusters of the stand. When moving the unit, at least two people should work together and lift the unit carefully, all the while keeping it level, and being very careful so as not to drop the unit on anyone’s feet.

* 5 1 0 0 0 2 1 6 0 2 - 0 1 *

Function Mode

Appendix



Index

AB Repeat . . . . . . . . . . . . . . . . . . . 13, 31

Accompaniment part . . . . . . . . . . . . 30

AC In (AC Inlet) . . . . . . . . . . . . . . . . . . 15

All Songs Play . . . . . . . . . . . . . . . . . . . 29

Ambience . . . . . . . . . . . . . . . . . . . 10, 22

[Ambience] button . . . . . . . . . . . . . . 22

Assembling. . . . . . . . . . . . . . . . . . . . . . 62

Audio Recording . . . . . . . . . . . . . . . . . 38

Audio Transpose . . . . . . . . . . . . . 39, 51

Auto O . . . . . . . . . . . . . . . . . . . . . . . . . 44

Brilliance . . . . . . . . . . . . . . . . . . . . 10, 23

[Brilliance] button . . . . . . . . . . . . . . . 23

[

] (Bwd) button . . . . . . . . . . . . 28

Cabinet Resonance . . . . . . . . . . . . . . 43

Center Cancel . . . . . . . . . . . . . . . 39, 51

Center Pedal . . . . . . . . . . . . . . . . . . . . . 52

Converting a Song . . . . . . . . . . . . . . . 37

Copy Song . . . . . . . . . . . . . . . . . . . . . . 45

Count-in. . . . . . . . . . . . . . . . . . . . . . . . . 27

CZERNY . . . . . . . . . . . . . . . . . . . . . 28, 59

Damper Noise . . . . . . . . . . . . . . . . . . . 43

Damper Pedal . . . . . . . . . . . . . . . . . . . 14

Damper Pedal Part . . . . . . . . . . . . . . . 52

Damper Resonance . . . . . . . . . . . . . . 42

Delete Song . . . . . . . . . . . . . . . . . . . . . 45

Display . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Display Contrast . . . . . . . . . . . . . . . . . 44

Dual Balance . . . . . . . . . . . . . . . . . . . . 51

Dual Play . . . . . . . . . . . . . . . . . . . . . . . . 19

Duplex Scale . . . . . . . . . . . . . . . . . . . . 42

Dynamic Harmonic . . . . . . . . . . . . . . 42

Eects . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

[E. Piano] button . . . . . . . . . . . . . . . . . 18

Erasing . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Factory Reset . . . . . . . . . . . . . . . . . . . . 44

[

] (Fast) button . . . . . . . . . . . . . . . . 26

FAVORITE . . . . . . . . . . . . . . . . . . . . . . . . 28

Format Media . . . . . . . . . . . . . . . . . . . 46

Function Mode . . . . . . . . . . . . . . . . . . 51

[

] (Fwd) button . . . . . . . . . . . . 28

Hammer Noise . . . . . . . . . . . . . . . . . . 42

Hammer Response . . . . . . . . . . . . . . 42

HANON . . . . . . . . . . . . . . . . . . . . . 28, 59

Headphone hook . . . . . . . . . . . . . . . . 14

Headphones 3D Ambience. . . 15, 51

Input jack . . . . . . . . . . . . . . . . . . . . . . . 15

Input Volume . . . . . . . . . . . . . . . . . . . . 51

Internal Song List . . . . . . . . . . . . . . . . 59

Ivory Feel Keyboard . . . . . . . . . . . . . . . 6

Key O Resonance . . . . . . . . . . . . . . . 43

Key Touch . . . . . . . . . . . . . . . . . . . 10, 23

Left-hand part . . . . . . . . . . . . . . . . . . . 30

Lid . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 42

Local Control . . . . . . . . . . . . . . . . . . . . 52

MASTERPIECE . . . . . . . . . . . . . . . 28, 59

Master Tuning . . . . . . . . . . . . . . . 43, 51

Memory Backup . . . . . . . . . . . . . 10, 44

Metronome . . . . . . . . . . . . . . . . . 12, 26

[Metronome] button . . . . . . . . . . . . . 26

Metronome’s Volume . . . . . . . . . . . . 27

MIDI Transmit Channel . . . . . . . . . . . 52

MIDI Visual Control . . . . . . . . . . . . . . 54

Music Rest . . . . . . . . . . . . . . . . . . . . . . . 16

Mute Volume . . . . . . . . . . . . . . . . . . . . 30

Muting . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Note Character . . . . . . . . . . . . . . . . . . 43

Note Volume . . . . . . . . . . . . . . . . . . . . 43

Octave Shift . . . . . . . . . . . . . . . . . . . . . 52

[Other] button . . . . . . . . . . . . . . . . . . . 18

Output jacks . . . . . . . . . . . . . . . . . . . . . 15

Overdubbing . . . . . . . . . . . . . . . . . . . . 34

Panel Lock . . . . . . . . . . . . . . . . . . . 13, 46

Part . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Part Mute . . . . . . . . . . . . . . . . . . . . . . . 30

Pedal connector . . . . . . . . . . . . . . . . . 15

Phones jacks . . . . . . . . . . . . . . . . . . . . 15

Piano Designer . . . . . . . . . . . . . . 11, 42

Piano Designer Demo . . . . . . . . . . . . 43

Piano [Grand] button . . . . . . . . . . . . 18

Piano [Upright] button . . . . . . . . . . . 18

Playback . . . . . . . . . . . . . . . . . . . . . . . . 13

Playing a Song . . . . . . . . . . . . . . . . . . . 28

[

] (Play/Stop) button . . . . 28

Power On/O . . . . . . . . . . . . . . . . . . . . 17

[Power] switch . . . . . . . . . . . . . . . . . . . 14

[ ] (Rec) button . . . . . . . . . . . . . . . 28

Recording . . . . . . . . . . . . . . . . . . . 13, 32

Recording Mode . . . . . . . . . . . . . . . . . 52

Renaming . . . . . . . . . . . . . . . . . . . . . . . 41

[

] (Reset) button . . . . . . . . . . . . . 28

Right-hand part . . . . . . . . . . . . . . . . . 30

Rotary eect . . . . . . . . . . . . . . . . . . . . . 18

Saving. . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Selecting a Song . . . . . . . . . . . . . 12, 28

SELECTIONS . . . . . . . . . . . . . . . . . 28, 59

[

] (Slow) button . . . . . . . . . . . . . . . 26

SMF Recording . . . . . . . . . . . . . . . . . . 32

Soft Pedal . . . . . . . . . . . . . . . . . . . . . . . 14

Song Balance . . . . . . . . . . . . . . . . 10, 29

[Song Balance] button . . . . . . . . . . . 29

[Song] button . . . . . . . . . . . . . . . . . . . 28

Sostenuto Pedal . . . . . . . . . . . . . . . . . 14

Soundboard Behavior. . . . . . . . . . . . 43

Split Play . . . . . . . . . . . . . . . . . . . . 11, 20

Split Point . . . . . . . . . . . . . . . . . . . . . . . 21

Stretch Tuning . . . . . . . . . . . . . . . . . . . 43

String Resonance . . . . . . . . . . . . . . . . 42

[Strings] button . . . . . . . . . . . . . . . . . . 18

Temperament . . . . . . . . . . . . . . . 43, 51

Temperament Key . . . . . . . . . . . 43, 51

Temperaments . . . . . . . . . . . . . . . . . . 43

Tempo . . . . . . . . . . . . . . . . . . . 12, 26, 29

Tempo Mute . . . . . . . . . . . . . . . . . . . . . 29

Time Signature . . . . . . . . . . . . . . 12, 26

Tone Demo . . . . . . . . . . . . . . . . . . . . . . 18

Tone groups . . . . . . . . . . . . . . . . . . . . . 18

Tone List . . . . . . . . . . . . . . . . . . . . . . . . 58

Top Lid . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Transpose . . . . . . . . . . . . . . . . . . . 10, 25

[Transpose] button . . . . . . . . . . . . . . 25

Transpose Mode . . . . . . . . . . . . . . . . . 52

Twin Piano . . . . . . . . . . . . . . . . . . 11, 24

[Twin Piano] button . . . . . . . . . . . . . . 24

Twin Piano Mode . . . . . . . . . . . . . . . . 24

USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

USB computer port . . . . . . . . . . . . . . 15

USB Driver . . . . . . . . . . . . . . . . . . . . . . . 53

USB Memory Mode . . . . . . . . . . . . . . 53

USB memory port . . . . . . . . . . . . . . . 15

Visual Control Channel . . . . . . . . . . . 53

Visual Control Function Chart . . . . 54

Visual Control Mode . . . . . . . . . . . . . 53

V-LINK . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

For EU Countries

For China

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Function Mode

Appendix

For the USA

For EU Countries

This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.

For the USA

FEDERAL COMMUNICATIONS COMMISSION

RADIO FREQUENCY INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment requires shielded interface cables in order to meet FCC class B limit.

Any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

CAN ICES-3 (B)/NMB-3 (B)

For C.A. US (Proposition 65

WARNING

This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.

DECLARATION OF CONFORMITY

Compliance Information Statement

Model Name :

Type of Equipment :

Responsible Party :

Address :

Telephone :

LX-15 Digital Piano Roland Corporation U.S. 5100 S. Eastern Avenue, Los Angeles, CA 90040-2938 (323) 890-3700

For Canada

For Korea

)

Operation Guide Panel Descriptions Before You Play Performing Practicing Piano Designer

Convenient Functions

Function Mode

Appendix

* 5 1 0 0 0 3 6 7 7 4 - 0 1 *

Roland LX-15e Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

USING THE UNIT SAFELY

IMPORTANT NOTES

About the Ivory Feel Keyboard

Look What You Can Do!

Operation Guide

Panel Descriptions

Before You Play

Opening/Closing the Lid

Opening/Closing the Top Lid

Performing

Performing with Various Sounds

Switching Tones

Performing with Two Layered Tones (Dual Play)

Adjusting the Sound to Your Taste

Adding Reverberation to the Sound (Ambience)

Adjusting the Brightness of the Sound (Brilliance)

Adjusting the Keyboard Response (Key Touch)

Dividing the Keyboard for Two-Person Performance (Twin Piano)

Shifting the Pitch (Transpose)

Practicing

Practicing with the Metronome

Changing the Tempo

Changing the Time Signature

Adjusting the Metronome’s Volume

Adding a Count-in to Synchronize Your Performance

Practicing with a Song

Selecting and Playing a Song

Playing Songs Consecutively (All Songs Play)

Adjusting the Volume Balance of the Song and the Keyboard Performance (Song Balance)

Adjusting a Song’s Tempo for Easier Practicing

Practicing One Hand at a Time (Part Mute)

Repeatedly Practicing a Portion of a Song (AB Repeat)

Recording the Song You’re Practicing

SMF recording

Overdubbing a Recorded Song

Converting a Song Recorded as an SMF to Audio

Audio Recording

Transposing a Song for Easier Performance (Audio Transpose)

Enjoying Karaoke with an Audio File (Center Cancel)

Renaming a Song

Personalizing Your Piano Sound (Piano Designer)

Making Detailed Adjustments to the Piano Sound

Convenient Functions

Adjusting the Brightness of the Display (Display Contrast)

Restoring the Factory Settings (Factory Reset)

Copying a Saved Song (Copy Song)

Deleting a Saved Song (Delete Song)

Initializing the Memory (Format Media)

Disabling the Buttons (Panel Lock)

Loading/Saving Piano Setups

Loading a Piano Setup

Saving a Piano Setup

About the Wireless LAN Function

Basic Connection Method (Connect by WPS)

Wireless LAN Function Settings

Status Indication

Connecting to a Wireless LAN Access Point That You Select (Select AP)

Other Settings (Option)

Various Settings (Function Mode)

Adjusting the Dual Play Volume Balance (Dual Balance)

Matching the Pitch with Other Instruments (Master Tuning)

Changing the Tuning Method (Temperament)

Specifying a Song’s Tonic (Temperament Key)

Adjusting the Volume of an Audio Playback Device (Input Volume)

Playing Back an Audio File with Its Central Sound Minimized (Center Cancel)

Transposing an Audio File (Audio Transpose)

Changing the Pitch of the Tone in Octave Steps (Octave Shift)

Selecting the Format for Recording (Recording Mode)

Changing How the Pedals Work (Center Pedal)

Preventing Doubled Notes When Connected to a Sequencer (Local Control)

MIDI Transmit Channel Settings (MIDI Transmit Channel)

Renaming a Song (Save Song)

Copying a Saved Song (Copy Song)

Deleting a Saved Song (Delete Song)

Initializing the Memory (Format Media)

Changing the USB Driver Settings (USB Driver)