Roland LVS-800 User Manual
Owner's Manual
Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and
“IMPORTANT NOTES” (Owner’s Manual p. 3-4; p. 5). These sections provide important
information concerning the proper operation of the unit. Additionally, in order to feel assured
that you have gained a good grasp of every feature provided by your new unit, Owner’s Manual
should be read in its entirety. The manual should be saved and kept on hand as a convenient
reference.
Copyright © 2009 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the
written permission of ROLAND CORPORATION.
USING THE UNIT SAFELY
Used for instructions intended to alert
the user to the risk of death or severe
injury should the unit be used
improperly.
Used for instructions intended to alert
the user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic
animals or pets.
002c
• Do not open (or modify in any way) the unit or its
AC adaptor.
..........................................................................................................
003
• Do not attempt to repair the unit, or replace parts
within it (except when this manual provides
specific instructions directing you to do so). Refer
all servicing to your retailer, the nearest Roland
Service Center, or an authorized Roland
distributor, as listed on the “Information” page.
..........................................................................................................
004
• Never install the unit in any of the following
locations.
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or
are
• Damp (e.g., baths, washrooms, on wet floors);
or are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness.
..........................................................................................................
007
• Make sure you always have the unit placed so it is
level and sure to remain stable. Never place it on
stands that could wobble, or on inclined surfaces.
..........................................................................................................
The symbol alerts the user to important instructions
or warnings.The specific meaning of the symbol is
determined by the design contained within the
triangle. In the case of the symbol at left, it is used for
The symbol alerts the user to items that must never
be carried out (are forbidden). The specific thing that
must not be done is indicated by the design contained
within the circle. In the case of the symbol at left, it
means that the unit must never be disassembled.
The ● symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In
the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.
008c
• Be sure to use only the AC adaptor supplied with
the unit. Also, make sure the line voltage at the
installation matches the input voltage specified on
the AC adaptor’s body. Other AC adaptors may
use a different polarity, or be designed for a
different voltage, so their use could result in
damage, malfunction, or electric shock.
..........................................................................................................
008e
• Use only the attached power-supply cord. Also,
the supplied power cord must not be used with
any other device.
..........................................................................................................
009
• Do not excessively twist or bend the power cord,
nor place heavy objects on it. Doing so can
damage the cord, producing severed elements
and short circuits. Damaged cords are fire and
shock hazards!
..........................................................................................................
011
• Do not allow any objects (e.g., flammable
material, coins, pins); or liquids of any kind
(water, soft drinks, etc.) to penetrate the unit.
..........................................................................................................
3
USING THE UNIT SAFELY
012b
• Immediately turn the power off, remove the AC
adaptor from the outlet, and request servicing by
your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on
the “Information” page when:
• The AC adaptor, the power-supply cord, or the
plug has been damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been
spilled onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally
or exhibits a marked change in performance.
..........................................................................................................
013
• In households with small children, an adult
should provide supervision until the child is
capable of following all the rules essential for the
safe operation of the unit.
..........................................................................................................
014
• Protect the unit from strong impact.
(Do not drop it!)
..........................................................................................................
015
• Do not force the unit’s power-supply cord to
share an outlet with an unreasonable number of
other devices. Be especially careful when using
extension cords—the total power used by all
devices you have connected to the extension
cord’s outlet must never exceed the power rating
(watts/amperes) for the extension cord. Excessive
loads can cause the insulation on the cord to heat
up and eventually melt through.
..........................................................................................................
016
• Before using the unit in a foreign country, consult
with your retailer, the nearest Roland Service
Center, or an authorized Roland distributor, as
listed on the “Information” page.
..........................................................................................................
101b
• The unit and the AC adaptor should be located so
their location or position does not interfere with
their proper ventilation.
..........................................................................................................
120c
• Always grasp only the plug on the powersupply cord when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
103b
• At regular intervals, you should unplug the AC
adaptor and clean it by using a dry cloth to wipe
all dust and other accumulations away from its
prongs. Also, disconnect the power plug from the
power outlet whenever the unit is to remain
unused for an extended period of time. Any
accumulation of dust between the power plug
and the power outlet can result in poor insulation
and lead to fire.
..........................................................................................................
104
• Try to prevent cords and cables from becoming
entangled. Also, all cords and cables should be
placed so they are out of the reach of children.
..........................................................................................................
106
• Never climb on top of, nor place heavy objects on
the unit.
..........................................................................................................
107c
• Never handle the AC adaptor or its plugs with
wet hands when plugging into, or unplugging
from, an outlet or this unit.
..........................................................................................................
108b
• Before moving the unit, disconnect the AC
adaptor and all cords coming from external
devices.
..........................................................................................................
109b
• Before cleaning the unit, turn off the power and
unplug the AC adaptor from the outlet.
..........................................................................................................
110b
• Whenever you suspect the possibility of lightning
in your area, disconnect the AC adaptor from the
outlet.
..........................................................................................................
118c
• Keep any screws you may remove and the
included plugs in a safe place out of children’s
reach, so there is no chance of them being
swallowed accidentally.
..........................................................................................................
4
IMPORTANT NOTES
Power Supply
301
• Do not connect this unit to same electrical outlet that is
being used by an electrical appliance that is controlled by
an inverter (such as a refrigerator, washing machine,
microwave oven, or air conditioner), or that contains a
motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit
to malfunction or may produce audible noise. If it is not
practical to use a separate electrical outlet, connect a
power supply noise filter between this unit and the
electrical outlet.
302
• The AC adaptor will begin to generate heat after long
hours of consecutive use. This is normal, and is not a
cause for concern.
307
• Before connecting this unit to other devices, turn off the
power to all units. This will help prevent malfunctions
and/or damage to other devices.
Placement
352a
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of such
receivers.
352b
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the vicinity of
this unit. Such noise could occur when receiving or initiating a call, or while conversing. Should you experience
such problems, you should relocate such wireless devices
so they are at a greater distance from this unit, or switch
them off.
355b
• When moved from one location to another where the
temperature and/or humidity is very different, water
droplets (condensation) may form inside the unit. Damage
or malfunction may result if you attempt to use the unit in
this condition. Therefore, before using the unit, you must
allow it to stand for several hours, until the condensation
has completely evaporated.
360
• Depending on the material and temperature of the surface
on which you place the unit, its rubber feet may discolor
or mar the surface.
You can place a piece of felt or cloth under the rubber feet
to prevent this from happening. If you do so, please make
sure that the unit will not slip or move accidentally.
Additional Precautions
• This unit allows you to switch images s at high speed. For
some people, viewing such images can cause headache,
nausea, or other discomfort. Do not use this unit to create
video that might cause these types of health
problems.Roland Corporation will accept no responsibility for any such health problems that may occur in
yourself or in viewers.
553
• Use a reasonable amount of care when using the unit’s
buttons, sliders, or other controls; and when using its jacks
and connectors. Rough handling can lead to malfunctions.
556
• When connecting / disconnecting all cables, grasp the
connector itself—never pull on the cable. This way you
will avoid causing shorts, or damage to the cable’s
internal elements.
559a
• When you need to transport the unit, package it in the box
(including padding) that it came in, if possible. Otherwise,
you will need to use equivalent packaging materials.
988
• Security Slot ( )
http://www.kensington.com/
Maintenance
401a
• For everyday cleaning wipe the unit with a soft, dry cloth
or one that has been slightly dampened with water. To
remove stubborn dirt, use a cloth impregnated with a
mild, non-abrasive detergent. Afterwards, be sure to wipe
the unit thoroughly with a soft, dry cloth.
402
• Never use benzine, thinners, alcohol or solvents of any
kind, to avoid the possibility of discoloration and/or
deformation.
5
Contents
Check the included items..................................................................................................................... 7
Names of Things and What They Do................................................................................................... 8
Top Panel ..................................................................................................................................................... 8
Rear Panel..................................................................................................................................................10
Connecting Peripheral Devices ......................................................................................................... 11
Connecting Source Devices..................................................................................................................... 11
Connecting Video Devices ............................................................................................................................ 11
Connecting Computers.................................................................................................................................. 11
Connecting Output Devices.................................................................................................................... 12
The Difference Between A/B MIX OUT and PGM OUT.......................................................................... 12
Connecting Output Devices.......................................................................................................................... 13
TALLY Output................................................................................................................................................ 13
Turning the Power On/Off .................................................................................................................. 14
Connecting the AC adaptor .................................................................................................................... 14
Turning the power on.............................................................................................................................. 15
Switching Between A Bus and B Bus ...............................................................................................16
Switching the Picture in the A/B Mode................................................................................................ 16
Switching the Picture Using the Video Fader ............................................................................................ 16
Switching Using the AUTO Button ............................................................................................................. 18
Use in Other Operation Modes Besides the A/B Mode .....................................................................19
Changing the Operation Mode..................................................................................................................... 19
Switching After Monitoring the Preview Picture (PGM-PST Mode)...................................................... 20
Switching the Picture Directly (LVS Mode)................................................................................................ 21
Using Picture-in-Picture to Composite Two Screens .......................................................................... 22
Composition in the A/B Mode or LVS Mode ............................................................................................22
Composition in the PGM-PST Mode ........................................................................................................... 24
Using the Downstream Keyer (DSK) ................................................................................................. 26
What’s a Downstream Keyer (DSK)? .................................................................................................... 26
Trying Out DSK Composition ................................................................................................................ 27
Combining DSK and Picture-in-Picture................................................................................................ 29
Applying Fade to the Final Output .................................................................................................... 30
Saving Settings to PANEL PRESET Buttons ................................................................................... 31
Saving the Current Settings ....................................................................................................................31
Calling Up Saved Settings....................................................................................................................... 31
Copying Saved Settings to Another Button.......................................................................................... 32
Exchanging Saved Settings with Another Button ............................................................................... 33
Returning to Factory-default State (Factory Reset)......................................................................... 34
Switching Between NTSC and PAL................................................................................................... 35
Changing Settings Using the Menus ................................................................................................ 36
Displaying the Menus.............................................................................................................................. 36
Menu Levels .............................................................................................................................................. 36
Menu Operations...................................................................................................................................... 37
Menu List ............................................................................................................................................. 38
Troubleshooting.................................................................................................................................. 44
Main Specifications ............................................................................................................................ 46
Remote Control......................................................................................................................................... 46
Index..................................................................................................................................................... 47
6
Check the included items
The following items are included. Please make sure that all items are present. If anything is missing, please contact your dealer.
LVS-800 itself
fig.LVS800-itself.eps
AC Adaptor (PSB-7U) and Power Cord
fig.PSB-7U.eps
RCA-BNC adaptor plugs (four)
fig.RCA-BNC-plug.eps
Owner’s Manual (this document)
fig.owners-manual.eps
7
Names of Things and What They Do
Top Panel
fig.top-panel.eps
4
5
6
7
1
2
3
12
13
14
15
16
17
1. V-LINK Button
This allows connection of V-LINK-compatible equipment from
Roland. To operate the RSS-V-Mixer by remote control, press
this button to switch it on.
What’s V-LINK?
V-LINK is a feature for performing video synchronized to
music using MIDI. The V-LINK feature provides a quick and
simple way to establish a link with a Roland instrument, musicproduction device, or video presenter.
During remote control of a V-LINK-compatible instrument,
music-production device, or video equipment via a MIDI
connection, this button lights up automatically when V-LINK is
switched on at the connected device.
For more information about remote control via MIDI, V-LINK,
or the RS-232C interface, please download the separately
available reference document from the following Roland
website.
http://www.rolandsystemsgroup.net/
8 9
10
11
2. SETUP Buttons (p. 36)
These are used for such tasks as displaying various menu items
and making system settings.
3. TIME Dial
This sets the transition time when performing a switch using
the AUTO button. It makes the following three AUTO-button
time settings.
•For A/B MIX
•For DSK
•For PGM OUTPUT FADE
4. PANEL PRESET Buttons (p. 31)
These save the current panel settings. Use them to instantly call
up saved panel settings.
5. PinP Buttons (p. 22)
These are used for Picture-in-Picture composition of the A Bus
video and B Bus video.
8
Names of Things and What They Do
6. A Bus/PGM Input Selectors (p. 16)
These select the video to input to A Bus.
*During use in the PGM-PST mode, you use these to select the video channel for program output.
7. B Bus/PST Input Selectors (p. 16)
These select the video to input to B Bus.
*During use in the PGM-PST mode, you use these to select the video for preview output.
8. TRANSITION Buttons for A/B MIX (p. 16)
These select the transition effect used during a transition between A Bus and B Bus.
9. AUTO Button for A/B MIX (p. 18)
This performs a transition between A Bus and B Bus by button operation, without using the video fader. It flashes during the transition
operation. When the transition ends, it goes dark.
10. TRANSITION Indicator
This displays the location of the video fader. The lighted location is changed by operation of the video fader or the AUTO button for A/B
MIX. Illumination of more elements toward the front of the unit indicates a greater ratio of B Bus video. Illumination of more elements
toward the back of the unit indicates a greater ratio of A Bus video.
11. Video Fader (p. 17)
This is a T-bar type video fader. You switch between A Bus and B Bus by moving it up and down.
12. PGM OUTPUT FADE Button (p. 30)
Operating this button automatically applies a fade-in or fade-out to program output. The time of the fade-in or fade-out is set using the TIME
dial. This lights up when a fade-out has been completed. It goes dark when a fade-in has been completed and program video is being output.
It flashes while a fade is in progress.
13. KEY LEVEL Dial (p. 28)
This adjusts the degree of the key composition.
14. BACKGROUND Buttons (p. 27)
These select the DSK background picture.
15. FOREGROUND Buttons (p. 27)
These select the DSK foreground picture.
16. TRANSITION Buttons for DSK (p. 27)
These select how the picture set for the foreground to appear and disappear.
17. AUTO Button for DSK (p. 28)
This displays the picture set for the foreground. It lights up when the foreground picture is output. It goes dark when the picture is not
output. It flashes while a mix is in progress.
9
Names of Things and What They Do
Rear Panel
241
3
8
9
1. PGM PVW Connector
This outputs the DSK preview picture. Before performing DSK
composition, you connect a monitor to check and verify the
video displayed as the DSK foreground. You can then
composite the background picture after first checking the logos,
text, or other images.
2. PGM OUT Connectors
These output the mixed video plus the DSK composition. You
connect them to projectors or other display equipment for the
final output.
Two composite connectors and one S-Video connector are
available. All connectors output the same picture.
3. A/B MIX PVW Connector
This outputs a preview picture for the video mix. You connect a
monitor for previewing a source prior to committing to a
transition. The current location of the video fader and the
selected video on the inactive bus are output.
A variety of setting menus are also displayed at the top of the
preview picture.
10
5 6
11 12
13
7. MONITOR OUT Connectors
These output signals being input via the VIDEO INPUT
connectors (composite or S-Video) without processing.
You can connect a monitor to each of these “loop-thru" monitor
outputs.
8. POWER Button
This switches the power on and off.
9. AC Adapter Connector
This is for connecting the included AC adapter (PSB-7U).
10. MIDI IN and OUT/THRU Connectors
Use these when connecting a MIDI device (a V-LINKcompatible product or the like) to operate the unit remotely, or
when using the unit to perform remote control of another
device.
11. RS-232C Connector
Use this when connecting an external device to operate the unit
remotely.
7
4. A/B MIX OUT Connectors
These output only the mix results for A Bus and B Bus. You can
connect a video deck or other such recording unit and record
the video prior to DSK composition.
Two composite connectors and one S-Video connector are
available. All connectors output the same picture.
5. PC INPUT Connectors
These are for RGB-signal input. You can connect computers that
serve as video source.
*Incoming computer signal will be downscalled to match the
resolution of other video sources.
6. VIDEO INPUT (Composite) Connectors
These are for composite-signal input. You can connect cameras
or other video sources.
10
For more information about remote control via MIDI, V-LINK,
or RS-232C interface, please download the separately available
reference materials from the following Roland website.
http://www.rolandsystemsgroup.net/
12. TALLY Connector
Provides low-current contact closure to activate tally lamps on
your cameras or tally light system.
13. VIDEO INPUT (S-Video) Connectors
These are for input of S-Video signals. You can connect cameras
or other video sources. When composite or RGB and S-Video
signals are simultaneously input to the same channel, the
S-Video signals take priority.
Connecting Peripheral Devices
Connecting Source Devices
To prevent malfunction or damage to video monitors or other devices, always turn off the power on all devices before
making any connections.
Connecting Video Devices
Channels 1 through 4 are exclusively for composite signals. S-Video can be connected to channels 5 through 8. Channels 5
and 6 can be used either for composite or S-Video, but S-Video takes priority when both types of signals are input.
*When connecting a device that has an RCA pin type connector to a composite input connector, use the included adapter plug.
fig.source-connect.eps
Video Cameras
Composite Cables and
RCA - BNC adaptor plugs
* When composite and S-Video
connections are made at 5 and
S-Video cables
Video Players
6, the S-Video takes priority.
* When a computer is connected
at PC1 and S-Video is connected
at 7, S-Video takes priority.
* When a computer is connected
at PC2 and S-Video is connected
at 8, S-Video takes priority.
Connecting Computers
Computers can be connected at the PC1 and PC2 connectors. A built-in scan converter converts the incoming RGB signal
to a standard definition video signal. Channels 7 and 8 can be used for both computer and S-Video input. When both
types of signals are input, the S-Video takes priority.
*The PC1 and PC2 input connectors on the LVS-800 are for D-Sub 15-pin cables. Using a cable adapter makes it possible to connect devices that have
DVI-I output connectors. A D-Sub 15-pin to DVI-I adapter is not included. Please purchase one separately.
fig.PC-connect.eps
D-Sub 15 pins VGA cable
Supported Resolutions
640 x 480 / 120Hz 800 x 600 / 120Hz
832 x 624 / 75Hz 1024 x 768 / 80Hz
1152 x 864 / 75Hz 1152 x 870 / 75Hz
1280 x 1024 / 75Hz 1600 x 1200 / 60Hz
* The refresh rate is the maximum value
of each resolution.
When displaying a movie from computer input, flicker or other picture corruption may occur. This is called tearing, and does not indicate an
equipment malfunction.
11
Connecting Peripheral Devices
Connecting Output Devices
The Difference Between A/B MIX OUT and PGM OUT
The LVS-800 is equipped with two sets of output connectors. These are the A/B MIX OUT connectors and the PGM OUT
connectors. The A/B MIX OUT connectors output only the results of the mixed video of A Bus and B Bus (A/B MIX). The
PGM OUT connectors output the results of the A/B mix plus your composited logos, text, etc (DSK composition). Final
output fade is enabled only for PGM OUT.
*In the figure shown below, 1 through 4 indicate where on the panels the respective internal blocks are located.
fig.ABmix-PGMout.eps
4
1
Ch2
Ch1
12345678
1
Ch3
Input Select
Ch4
Ch5
Ch6
Ch7
3
2
Ch8
PC1 PC2
Scan Converter
12
Bus A Bus B
2
Video Mixer
Background
3
4
A/B MIX OUT
PGM OUT
Foreground
DSK
Output Fade
Connecting Peripheral Devices
Connecting Output Devices
You can connect displays or capture devices to the A/B MIX OUT in order to view or capture the output of the A/B mix
only (no DSK). You should connect displays or capture devices to the PGM OUT jacks in order to view or capture the
final mix of A/B mix plus DSK. You can connect source monitors to the MONITOR OUT jacks to have at-a-glance
monitoring of all your input sources. Monitors connected to the A/B MIX PVW or PGM PVW jacks will allow you to
preview sources.
*When computers are connected to the PC1 and PC2 input connectors, the scan-converted video signals are output from the 7/PC1 and 8/PC2 output
connectors.
*The output from A/B MIX PVW displays on-screen menu items in addition to the video before transition.
fig.output-devices.eps
Projectors
Recorder
Composite
(BNC - BNC)
Composite
(BNC - BNC)
S-Video
Composite
(BNC - BNC)
Source Monitors
Preview Monitors
TALLY Output
The LVS-800 is equipped with a D-Sub 15-pin TALLY output connector. Connecting a video monitor capable of tally
input to this makes it possible to illuminate the tally lamps on the monitor. The lamp is switched on and off according to
the channel selection, enabling you to see which channel is currently in use on the monitor.
The pin assignment is as shown below. The LVS-800 uses an open-collector tally output (closed contact).
*Connecting a video monitor capable of tally input requires a cable that must be obtained separately.
fig.tally-config.eps
Pin No. Channel
12345
678910
1
2
3
4
5
6
7
8
9
10
11
1112131415
12
13
14
15
Ch1
Ch5
NC
GND
Ch4
Ch2
Ch6
NC
GND
Ch8
Ch3
Ch7
NC
GND
NC
13
Turning the Power On/Off
Connecting the AC adaptor
Connect the AC adaptor to LVS-800. Place the AC adaptor so the side with the indicator (see illustration) faces upwards
and the side with textual information faces downwards. The indicator will light when you plug the AC adaptor into an
AC outlet.
fig.connect-PSB7U.eps
Indicator
About Cord Hook
To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid
applying undue stress to the AC adaptor connector, anchor the power cord using the cord hook, as shown in the
illustration.
fig.cord-hook.eps
Caution regarding the power supply
Depending on the circumstances of a particular setup, you may experience a discomforting sensation, or perceive that the
surface feels gritty to the touch when you touch this device, cameras connected to it, or the metal portions of other
objects, such as VCRs. This is due to an infinitesimal electrical charge, which is absolutely harmless. However, if you are
concerned about this, connect the ground terminal (see figure) with an external ground. When the unit is grounded, a
slight noise may occur, depending on the particulars of your installation. If you are unsure of the connection method,
contact the nearest Roland Service Center, or an authorized Roland distributor, as listed on the “Information” page.
fig.earth-terminal.eps
Unsuitable places for connection
•Water pipes (may result in shock or electrocution)
•Gas pipes (may result in fire or explosion)
•Telephone-line ground or lightning rod (may be dangerous in the event of lightning)
14
Turning the Power On/Off
Turning the power on
*Once the connections have been completed (p. 14), turn on power to your various devices in the order specified. By turning on devices in the wrong
order, you risk causing malfunction and/or damage to monitors and other devices.
*This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally.
Turning the power on
Make sure that the AC adaptor is correctly connected. Press the [POWER] button located on rear panel. It takes few
seconds to boot the system.
fig.power-on.eps
Turning the power off
Press the [POWER] button located on rear panel. Check all indicators/LEDs to turn off.
15
Switching Between A Bus and B Bus
B
Input sources are selected and switched between the A Bus and the B Bus. The unit has eight input selectors for each Bus,
and you choose the input video for each bus before you perform the transition.
With the LVS-800, you can switch between A Bus and B Bus in three different modes. Operation of each of these modes is
described below.
•A/B mode This performs switching using the video fader or the [AUTO] button for A/B MIX.
•PGM-PST mode This lets you check the preview picture before switching and perform the transition using the [AUTO] button.
•LVS mode This lets you perform switching directly, using only the input selector buttons.
The results of these operations are output from the A/B MIX OUT connectors. If you want to output the results from the
PGM OUT connectors as well, make the settings described below.
•At [PGM OUTPUT FADE], switch off the [AUTO] button.
•At DSK, for [BACKGROUND], select [A/B MIX].
•Switch off the [AUTO] button for DSK.
Switching the Picture in the A/B Mode
Switching the Picture Using the Video Fader
1. Choose the A Bus and B Bus video.
Select the channels of the video input to A Bus and B Bus. Selecting an input channel makes the LED for the button light
up. For information about what the color of the LED means, see the following page.
fig.AB-source-select.eps
2. Choose the type of transition (transition effect).
If you want to apply a transition effect, use a [TRANSITION] button to choose [MIX], [WIPE1], or [WIPE2]. To apply no
effect, choose [CUT].
fig.select-transition.eps
CUT
MIX
WIPE1
WIPE2
16
Start Finish
A B
A BAB
A B
A B
A
A
No transition effect is applied.
The pictures on A and B are blended together
as they are switched.
The video switches using horizontal wipe.
(factory default setup)
The video switches using box wipe from center
(factory default setup)
Loading...