Roland Juno-Di Implementation
■
●
●
●
●
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Model: JUNO-Di
MIDI Implementation
Date: May 1, 2009
Version: 1.00
1. Data Reception
* Parameters marked with “*” in this document can be viewed by using “JUNO-Di Editor.”
Channel Voice Messages
* Not received in Performance mode when the RCV MIDI (Receive MIDI) parameter (PERFORM/
MIDI) is OFF.
Note off
Status 2nd byte 3rd byte
8nH kkH vvH
9nH kkH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
* Not received when the ENV MODE (Envelope MODE) parameter (PATCH/CONTROL SW or
RHYTHM/COMMON+CONTROL) is NO-SUS.
Note on
Status 2nd byte 3rd byte
9nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
Polyphonic Key Pressure
Status 2nd byte 3rd byte
AnH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = Polyphonic Key Pressure: 00H - 7FH (0 - 127)
* Not received in Performance mode when the RCV POLY PRESS (Receive Polyphonic Key
Pressure) parameter (PERFORM/MIDI) is OFF.
Control Change
* If the corresponding Controller number is selected for the PATCH MATRIX CONTROL SOURCE
1, 2, 3 or 4 parameter (PATCH/MATRIX CONTROL), the corresponding effect will occur.
* If a Controller number that corresponds to the SYSTEM CTRL SRC 1, 2, 3 or 4 parameter
(SYSTEM/COMMON) is selected, the specified effect will apply if PATCH MATRIX CONTROL
SOURCE 1, 2, 3 or 4 parameter (PATCH/MATRIX CONTROL) is set to SYS-CTRL1, SYS-CTRL2, SYS-
CTRL3 or SYS-CTRL4.
Bank Select (Controller number 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* Not received in Performance mode when the RCV BS (Receive Bank Select) (PERFORM/MIDI) is
OFF.
* The Performances, Patches, and Rhythms corresponding to each Bank Select are as follows.
BANK SELECT | PROGRAM | GROUP | NUMBER
MSB | LSB | NUMBER | |
-----+-----------+-----------+----------------------+---------- 000 | | 001 - 128 | GM Patch | 001 - 256
: | | | |
063 | | 001 - 128 | GM Patch | 001 - 256
085 | 000 | 001 - 064 | User Performance | 001 - 064
| 064 | 001 - 064 | Preset Performance | 001 - 064
086 | 000 | 001 - 008 | User Rhythm | 001 - 008
| 064 | 001 - 020 | Preset Rhythm | 001 - 020
087 | 000 | 001 - 128 | User Patch | 001 - 128
| 064 | 001 - 128 | Preset Patch | 001 - 128
| 065 | 001 - 128 | Preset Patch | 001 - 128
| : | | : |
| 072 | 001 - 058 | Preset Patch |
120 | | 001 - 057 | GM Rhythm | 001 - 009
121 | 000 - | 001 - 128 | GM Patch | 001 - 256
Modulation (Controller number 1)
Status 2nd byte 3rd byte
BnH 01H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Modulation depth: 00H - 7FH (0 - 127)
* Not received in Performance mode when the RCV MOD (Receive Modulation) parameter
(PERFORM/MIDI) is OFF.
Breath type (Controller number 2)
Status 2nd byte 3rd byte
BnH 02H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
Foot type (Controller number 4)
Status 2nd byte 3rd byte
BnH 04H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
Portamento Time (Controller number 5)
Status 2nd byte 3rd byte
BnH 05H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Portamento Time: 00H - 7FH (0 - 127)
* In Performance mode, the PORTAMENTO TIME parameter (PERFORM/ALL PARAMETER) will
change.
Data Entry (Controller number 6, 38)
Status 2nd byte 3rd byte
BnH 06H mmH
BnH 26H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
Volume (Controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Volume: 00H - 7FH (0 - 127)
* Not received in Performance mode when the RCV VOLUME (Receive Volume) parameter
(PERFORM/MIDI) is OFF.
* In Performance mode, the LEVEL parameter (PERFORM/ALL PARAMETERS) (on the JUNO-Di,
the Part Level parameter (PART EDIT)) will change.
Panpot (Controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Panpot: 00H - 40H - 7FH (Left - Center - Right),
* Not received in Performance mode when the RCV PAN (Receive PAN) parameter (PERFORM/
MIDI) is OFF.
* In Performance mode, the PAN parameter (PERFORM/ALL PARAMETERS) will change.
Expression (Controller number 11)
Status 2nd byte 3rd byte
BnH 0BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
* Not received when RCV EXP (Receive Expression) parameter (PATCH/CONTROL SW or
RHYTHM/COMMON+CONTROL) is OFF.
* Not received in Performance mode when RCV EXP (Receive Expression) parameter (PERFORM/
MIDI) is OFF.
Hold 1 (Controller number 64)
Status 2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* Not received when RCV HOLD-1 (Receive Hold-1) parameter (PATCH/CONTROL SW or
RHYTHM/COMMON+CONTROL) is OFF.
* Not received in Performance mode when RCV HOLD-1 (Receive Hold-1) parameter (PERFORM/
MIDI) is OFF.
* When the REDAMPER parameter (PATCH/CONTROL SW) is turned ON, 128 discrete steps are
recognized for the value.
1PS
Copyright © 2009 ROLAND CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
1
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
MIDI Implementation
❍
❍
❍
❍
❍
❍
Portamento (Controller number 65)
Status 2nd byte 3rd byte
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* In Performance mode, the PORTAMENTO SW parameter (PERFORM/ALL PARAMETERS) will
change.
Sostenuto (Controller number 66)
Status 2nd byte 3rd byte
BnH 42H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
Soft (Controller number 67)
Status 2nd byte 3rd byte
BnH 43H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
Legato Foot Switch (Controller number 68)
Status 2nd byte 3rd byte
BnH 44H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
* In Performance mode, the LEGATO parameter (PERFORM/ALL PARAMETERS) will change.
Hold-2 (Controller number 69)
Status 2nd byte 3rd byte
BnH 45H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* A hold movement isn’t done.
Resonance (Controller number 71)
Status 2nd byte 3rd byte
BnH 47H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the OFFSET RES (Resonance) parameter (PERFORM/ALL PARAMETERS)
will change.
Release Time (Controller number 72)
Status 2nd byte 3rd byte
BnH 48H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the OFFSET REL (Release) parameter (PERFORM/ALL PARAMETERS) will
change.
Attack time (Controller number 73)
Status 2nd byte 3rd byte
BnH 49H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63),
* In Performance mode, the OFFSET ATK (Attack) parameter (PERFORM/ALL PARAMETERS) will
change.
Cutoff (Controller number 74)
Status 2nd byte 3rd byte
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
Decay Time (Controller number 75)
Status 2nd byte 3rd byte
BnH 4BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Decay Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the OFFSET DCY (Decay) parameter (PERFORM/ALL PARAMETERS) will
change.
Vibrato Rate (Controller number 76)
Status 2nd byte 3rd byte
BnH 4CH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Rate value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the VIBRATO RATE parameter (PERFORM/ALL PARAMETERS) will
change.
Vibrato Depth (Controller number 77)
Status 2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Depth Value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the VIBRATO DEPTH parameter (PERFORM/ALL PARAMETERS) will
change.
Vibrato Delay (Controller number 78)
Status 2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Vibrato Delay value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
* In Performance mode, the VIBRATO DELAY parameter (PERFORM/ALL PARAMETERS) will
change.
General Purpose Controller 5 (Controller number 80)
Status 2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The LEVEL parameter (PATCH/TVA) of Tone 1 will change.
General Purpose Controller 6 (Controller number 81)
Status 2nd byte 3rd byte
BnH 51H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The LEVEL parameter (PATCH/TVA) of Tone 2 will change.
General Purpose Controller 7 (Controller number 82)
Status 2nd byte 3rd byte
BnH 52H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The LEVEL parameter (PATCH/TVA) of Tone 3 will change.
General Purpose Controller 8 (Controller number 83)
Status 2nd byte 3rd byte
BnH 53H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The LEVEL parameter (PATCH/TVA) of Tone 4 will change.
* In Performance mode, the OFFSET COF (Cutoff) parameter (PERFORM/ALL PARAMETERS) will
change.
2
❍
❍
❍
❍
●
●
●
■
●
●
●
●
MIDI Implementation
Portamento control (Controller number 84)
Status 2nd byte 3rd byte
BnH 54H kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control message will change continuously
in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number, this
voice will continue sounding (i.e., legato) and will, when the next Note-on is received,
smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the Portamento
Time value.
Effect 1 (Reverb Send Level) (Controller number 91)
Status
BnH 5BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Reverb Send Level: 00H - 7FH (0 - 127)
* In Performance mode, the REVERB (Reverb Send Level) parameter (PERFORM/MIXER) will
change.
2nd byte 3rd byte
Effect 3 (Chorus Send Level) (Controller number 93)
Status
BnH 5DH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Chorus Send Level: 00H - 7FH (0 - 127)
* In Performance mode, the CHORUS (Chorus Send Level) parameter (PERFORM/MIXER) will
change.
2nd byte 3rd byte
RPN MSB/LSB (Controller number 100, 101)
Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any order)
should be sent in order to select the parameter, then Data Entry (Controller numbers 6 and 38)
should be sent to set the value. Once RPN messages are received, Data Entry messages that is
received at the same MIDI channel after that are recognized as changing toward the value of the
RPN messages. In order not to make any mistakes, transmitting RPN Null is recommended after
setting parameters you need.
This device receives the following RPNs.
RPN Data entry
MSB, LSB
00H, 00H mmH, llH Pitch Bend Sensitivity
* In Performance mode, the PB RANGE (Pitch Bend Range) parameter (PERFORM/ALL
PARAMETERS) will change.
00H, 01H mmH, llH Channel Fine Tuning
* In Performance mode, the TUNE FINE parameter (PERFORM/ALL PARAMETERS) will change.
00H, 02H mmH, llH Channel Coarse Tuning
* In Performance mode, the TUNE COARSE parameter (PERFORM/ALL PARAMETERS) will change.
00H, 05H mmH, llH Modulation Depth Range
* Not received in Patch mode.
7FH, 7FH ---, --- RPN null
MSB, LSB Notes
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
mm, ll: 00 00H - 00 06H
(0 - 16384 x 600 / 16384 cent)
RPN and NRPN will be set as “unspecified.” Once this
setting has been made, subsequent
Parameter values that were previously set will not
change.
mm, ll: ignored
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H - FH (ch.1 - 16)
pp = Program number: 00H - 7FH (prog.1 - prog.128)
* Not received in Performance mode when the RCV PC (Receive Program Change) parameter
(PERFORM/MIDI) is OFF.
Channel Pressure
Status
DnH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Channel Pressure: 00H - 7FH (0 - 127)
* Not received in Performance mode when the RCV CH PRESS (Receive Channel Pressure)
parameter (PERFORM/MIDI) is OFF.
2nd byte
Pitch Bend Change
Status
EnH llH mmH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Not received when the RCV BENDER (Receive Bender) parameter (PATCH/CONTROL SW) is OFF.
* Not received in Performance mode when the RCV PB (Receive Pitch Bend) parameter
(PERFORM/MIDI) is OFF.
2nd byte 3rd byte
Channel Mode Messages
* Not received in Performance mode when the RCV MIDI (Receive MIDI) parameter (PERFORM/
MIDI) is OFF.
All Sounds Off (Controller number 120)
Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, all notes currently sounding on the corresponding channel will
be turned off.
Reset All Controllers (Controller number 121)
Status
BnH 79H 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When this message is received, the following controllers will be set to their reset values.
Controller
Pitch Bend Change +/-0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath Type 0 (min)
Expression 127 (max)
Hold 1 0 (off)
Sostenuto 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change
All Notes Off (Controller number 123)
Status
BnH 7BH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned off.
However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned off.
OMNI OFF (Controller number 124)
Status 2nd byte 3rd byte
BnH 7CH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
2nd byte 3rd byte
Reset value
However the controller will be at minimum.
2nd byte 3rd byte
3
MIDI Implementation
●
●
●
■
●
●
●
●
●
■
●
❍
❍
❍
❍
OMNI ON (Controller number 125)
Status 2nd byte 3rd byte
BnH 7DH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received. OMNI ON will not be
turned on.
MONO (Controller number 126)
Status 2nd byte 3rd byte
BnH 7EH mmH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm = mono number: 00H - 10H (0 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the MONO/POLY parameter (PERFORM/ALL PARAMETERS) will change.
POLY (Controller number 127)
Status 2nd byte 3rd byte
BnH 7FH 00H
n = MIDI channel number: 0H - FH (ch.1 - 16)
* The same processing will be carried out as when All Notes Off is received.
* In Performance mode, the MONO/POLY parameter (PERFORM/ALL PARAMETERS) will change.
System Realtime Message
Timing Clock
Status
F8H
* Received by the JUNO-Di if the Sync Mode parameter (SYSTEM/MIDI) is set to SLAVE.
Start
Status
FAH
* Received by the JUNO-Di if the Sync Mode parameter (SYSTEM/MIDI) is set to SLAVE.
Continue
Status
FBH
* Received by the JUNO-Di if the Sync Mode parameter (SYSTEM/MIDI) is set to SLAVE.
Stop
Status
FCH
* Received by the JUNO-Di if the Sync Mode parameter (SYSTEM/MIDI) is set to SLAVE.
Active Sensing
Status
FEH
* When Active Sensing is received, the unit will begin monitoring the intervals of all further
messages. While monitoring, if the interval between messages exceeds 420 ms, the same
processing will be carried out as when All Sounds Off, All Notes Off and Reset All Controllers
are received, and message interval monitoring will be halted.
System Exclusive Message
Status
F0H iiH, ddH, ......,eeH F7H
F0H: System Exclusive Message status
ii = ID number: an ID number (manufacturer ID) to indicate the manufacturer whose
dd,...,ee = data: 00H - 7FH (0 - 127)
F7H: EOX (End Of Exclusive)
Of the System Exclusive messages received by this device, the Universal Non-realtime messages
and the Universal Realtime messages and the Data Request (RQ1) messages and the Data Set
(DT1) messages will be set automatically.
Universal Non-realtime System Exclusive Messages
Identity Request Message
Status
F0H 7EH, dev, 06H, 01H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
dev Device ID (dev: 10H, 7FH)
06H Sub ID#1 (General Information)
01H Sub ID#2 (Identity Request)
F7H EOX (End Of Exclusive)
* When this message is received, Identity Reply message (p. 9) will be transmitted.
GM1 System On
Status
F0H 7EH, 7FH, 09H, 01H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
09H Sub ID#1 (General MIDI Message)
01H Sub ID#2 (General MIDI 1 On)
F7H EOX (End Of Exclusive)
* When this messages is received, this instrument will turn to the Performance mode.
GM2 System On
Status
F0H 7EH 7FH 09H 03H F7H
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
09H Sub ID#1 (General MIDI Message)
03H Sub ID#2 (General MIDI 2 On)
F7H EOX (End Of Exclusive)
* When this messages is received, this instrument will turn to the Performance mode.
GM System Off
Status
F0H 7EH, 7F, 09H, 02H F7H
Data byte Status
Exclusive message this is. Roland’s manufacturer ID is 41H.
ID numbers 7EH and 7FH are extensions of the MIDI standard; Universal
Non-realtime Messages (7EH) and Universal Realtime Messages (7FH).
Data byte Status
Data byte Status
Data byte Status
Data byte Status
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
09H Sub ID#1 (General MIDI Message)
02H Sub ID#2 (General MIDI Off)
F7H EOX (End Of Exclusive)
* When this messages is received, this instrument will return to the Performance mode.
4
●
❍
❍
❍
●
❍
❍
❍
MIDI Implementation
Universal Realtime System Exclusive Messages
Master Volume
Status Data byte Status
F0H 7FH, 7FH, 04H, 01H, llH, mmH F7H
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
04H Sub ID#1 (Device Control)
01H Sub ID#2 (Master Volume)
llH Master Volume lower byte
mmH Master Volume upper byte
F7H EOX (End Of Exclusive)
* The lower byte (llH) of Master Volume will be handled as 00H.
* The MASTER LEVEL parameter (SYSTEM/COMMON) will change.
Master Fine Tuning
Status Data byte Status
F0H 7FH, 7FH, 04H, 03H, llH, mmH F7H
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
04H Sub ID#1 (Device Control)
03H Sub ID#2 (Master Fine Tuning)
llH Master Fine Tuning LSB
mmH Master Fine Tuning MSB
F7H EOX (End Of Exclusive)
mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.9 [cents])
* The MASTER TUNE parameter (SYSTEM/COMMON) (on the JUNO-Di, the Master Tune
parameter (SYSTEM/SOUND)) will change.
Master Coarse Tuning
Status Data byte Status
F0H 7FH, 7FH, 04H, 04H, llH, mmH F7
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
04H Sub ID#1 (Device Control)
04H Sub ID#2 (Master Coarse Tuning)
llH Master Coarse Tuning LSB
mmH Master Coarse Tuning MSB
F7H EOX (End Of Exclusive)
llH: ignored (processed as 00H)
mmH: 28H - 40H - 58H (-24 - 0 - +24 [semitones])
* The MASTER KEY SHIFT parameter (SYSTEM/COMMON) will change.
Global Parameter Control
* Not received in Patch mode.
Reverb Parameters
Status Data byte Status
F0H 7FH, 7FH, 04H, 05H, 01H, 01H, F7H
01H, 01H, 01H, ppH, vvH
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
04H Sub ID#1 (Device Control)
05H Sub ID#2 (Global Parameter Control)
01H Slot path length
01H Parameter ID width
01H Value width
01H Slot path MSB
01H Slot path LSB (Effect 0101: Reverb)
ppH Parameter to be controlled.
vvH Value for the parameter.
pp=0 Reverb Type
vv = 00H Small Room
vv = 01H Medium Room
vv = 02H Large Room
vv = 03H Medium Hall
vv = 04H Large Hall
vv = 08H Plate
pp=1 Reverb Time
vv = 00H - 7FH 0 - 127
F7H EOX (End Of Exclusive)
Chorus Parameters
Status Data byte Status
F0H 7FH, 7FH, 04H, 05H, 01H, 01H, F7H
01H, 01H, 02H, ppH, vvH
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
04H Sub ID#1 (Device Control)
05H Sub ID#2 (Global Parameter Control)
01H Slot path length
01H Parameter ID width
01H Value width
01H Slot path MSB
02H Slot path LSB (Effect 0102: Chorus)
ppH Parameter to be controlled.
vvH Value for the parameter.
pp=0 Chorus Type
vv=0 Chorus1
vv=1 Chorus2
vv=2 Chorus3
vv=3 Chorus4
vv=4 FB Chorus
vv=5 Flanger
pp=1 Mod Rate
vv= 00H - 7FH 0 - 127
pp=2 Mod Depth
vv = 00H - 7FH 0 - 127
pp=3 Feedback
vv = 00H - 7FH 0 - 127
pp=4 Send To Reverb
vv = 00H - 7FH 0 - 127
F7H EOX (End Of Exclusive)
Channel Pressure
Status Data byte Status
F0H 7FH, 7FH, 09H, 01H, 0nH, ppH, rrH F7H
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
09H Sub ID#1 (Controller Destination Setting)
01H Sub ID#2 (Channel Pressure)
0nH MIDI Channel (00 - 0F)
ppH Controlled parameter
rrH Controlled range
pp=0 Pitch Control
rr = 28H - 58H -24 - +24 [semitones]
pp=1 Filter Cutoff Control
rr = 00H - 7FH -9600 - +9450 [cents]
pp=2 Amplitude Control
rr = 00H - 7FH 0 - 200%
pp=3 LFO Pitch Depth
rr = 00H - 7FH 0 - 600 [cents]
pp=4 LFO Filter Depth
rr = 00H - 7FH 0 - 2400 [cents]
pp=5 LFO Amplitude Depth
rr = 00H - 7FH 0 - 100%
F7H EOX (End Of Exclusive)
5
MIDI Implementation
❍
❍
❍
●
❍
Controller
Status Data byte Status
F0H 7FH, 7FH, 09H, 03H, 0nH, ccH, ppH, rrH F7H
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
09H Sub ID#1 (Controller Destination Setting)
03H Sub ID#2 (Control Change)
0nH MIDI Channel (00 - 0F)
ccH Controller number (01 - 1F, 40 - 5F)
ppH Controlled parameter
rrH Controlled range
pp=0 Pitch Control
rr = 28H - 58H -24 - +24 [semitones]
pp=1 Filter Cutoff Control
rr = 00H - 7FH -9600 - +9450 [cents]
pp=2 Amplitude Control
rr = 00H - 7FH 0 - 200%
pp=3 LFO Pitch Depth
rr = 00H - 7FH 0 - 600 [cents]
pp=4 LFO Filter Depth
rr = 00H - 7FH 0 - 2400 [cents]
pp=5 LFO Amplitude Depth
rr = 00H - 7FH 0 - 100%
F7H EOX (End Of Exclusive)
Scale/Octave Tuning Adjust
Status Data byte Status
F0H 7EH, 7FH, 08H, 08H, ffH, ggH, hhH, ssH... F7
Byte Explanation
F0H Exclusive status
7EH ID number (Universal Non-realtime Message)
7FH Device ID (Broadcast)
08H Sub ID#1 (MIDI Tuning Standard)
08H Sub ID#2 (scale/octave tuning 1-byte form)
ffH Channel/Option byte 1
bits 0 to 1 = channel 15 to 16
bit 2 to 6 = Undefined
ggH Channel byte 2
bits 0 to 6 = channel 8 to 14
hhH Channel byte 3
bits 0 to 6 = channel 1 to 7
ssH 12 byte tuning offset of 12 semitones from C to B
00H = -64 [cents]
40H = 0 [cents] (equal temperament)
7FH = +63 [cents]
F7H EOX (End Of Exclusive)
Data Transmission
This instrument can use exclusive messages to exchange many varieties of internal settings with
other devices.
The model ID of the exclusive messages used by this instrument is 00H 00H 3AH.
Data Request 1 (RQ1)
This message requests the other device to transmit data. The address and size indicate the type
and amount of data that is requested.
When a Data Request message is received, if the device is in a state in which it is able to transmit
data, and if the address and size are appropriate, the requested data is transmitted as a Data Set 1
(DT1) message. If the conditions are not met, nothing is transmitted.
Status Data byte Status
F0H 41H, dev, 00H, 00H, 3AH, 11H, aaH, bbH, ccH, F7H
ddH, ssH, ttH, uuH, vvH, sum
Byte Remarks
F0H Exclusive status
41H ID number (Roland)
dev device ID (dev: 10H, 7FH)
00H model ID #1 (JUNO-Di)
00H model ID #2 (JUNO-Di)
3AH model ID #3 (JUNO-Di)
11H command ID (RQ1)
aaH address MSB
bbH address
ccH address
ddH address LSB
ssH size MSB
ttH size
uuH size
vvH size LSB
sum checksum
F7H EOX (End Of Exclusive)
* The size of data that can be transmitted at one time is fixed for each type of data. And data
requests must be made with a fixed starting address and size. Refer to the address and size
given in “Parameter Address Map” (p. 10).
* For the checksum, refer to p. 24.
Key-based Instrument Controllers
Status Data byte Status
F0H 7FH, 7FH, 0AH, 01H, 0nH, kkH, nnH, vvH F7H
Byte Explanation
F0H Exclusive status
7FH ID number (universal realtime message)
7FH Device ID (Broadcast)
0AH Sub ID#1 (Key-Based Instrument Control)
01H Sub ID#2 (Controller)
0nH MIDI Channel (00 - 0FH)
kkH Key Number
nnH Control Number
vvH Value
::
F7 EOX (End Of Exclusive)
* This parameter affects drum instruments only.
nn=07H Level
vv = 00H - 7FH 0 - 200% (Relative)
nn=0AH Pan
vv = 00H - 7FH Left - Right (Absolute)
nn=5BH Reverb Send
vv = 00H - 7FH 0 - 127 (Absolute)
nn=5D Chorus Send
vv = 00H - 7FH 0 - 127 (Absolute)
6
Data set 1 (DT1)
Status Data byte Status
F0H 41H, dev, 00H, 00H, 3AH, 12H, aaH, bbH, F7H
ccH, ddH, eeH, ... ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 10H, 7FH)
00H Model ID #1 (JUNO-Di)
00H Model ID #2 (JUNO-Di)
3AH Model ID #3 (JUNO-Di)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the data to be
sent
bbH Address: upper middle byte of the starting address of the
data to be sent
ccH Address: lower middle byte of the starting address of the data
to be sent
ddH Address LSB: lower byte of the starting address of the data to be
sent.
eeH Data: the actual data to be sent. Multiple bytes of data are
transmitted in order starting from the address.
: :
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
❍
MIDI Implementation
* The amount of data that can be transmitted at one time depends on the type of data, and data
will be transmitted from the specified starting address and size. Refer to the address and size
given in “Parameter Address Map” (p. 10).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each packet
will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to p. 24.
Status Data byte Status
F0H 41H, dev, 42H, 12H, aaH, bbH, ccH, F7H
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 10H, 7FH)
42H Model ID (GS)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the
bbH Address: middle byte of the starting address of the
ccH Address LSB: lower byte of the starting address of the transmitted
ddH Data: the actual data to be transmitted. Multiple bytes of
: :
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and data
will be transmitted from the specified starting address and size. Refer to the address and size
given in “Parameter Address Map” (p. 10).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each packet
will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to p. 24.
ddH, ... eeH, sum
transmitted data
transmitted data
data
data are transmitted starting from the address.
7
MIDI Implementation
■
●
●
●
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
2. Data Transmission
Channel Voice Messages
Note off
Status
8nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note off velocity: 00H - 7FH (0 - 127)
Note on
Status
9nH kkH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = note number: 00H - 7FH (0 - 127)
vv = note on velocity: 01H - 7FH (1 - 127)
Control Change
* By selecting a controller number that corresponds to the setting of parameters of controllers,
the JUNO-Di can transmit any control change message.
Bank Select (Controller number 0, 32)
Status
BnH 00H mmH
BnH 20H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = Bank number: 00 00H - 7F 7FH (bank.1 - bank.16384)
* These messages are transmitted when Patch, Rhythm Set or Performance is selected.
Modulation (Controller number 1)
Status
BnH 01H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Modulation depth: 00H - 7FH (0 - 127)
Breath type (Controller number 2)
Status
BnH 02H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
Portamento Time (Controller number 5)
Status
BnH 05H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Portamento Time: 00H - 7FH (0 - 127)
Data Entry (Controller number 6, 38)
Status
BnH 06H mmH
BnH 26H llH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
Volume (Controller number 7)
Status
BnH 07H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Volume: 00H - 7FH (0 - 127)
Panpot (Controller number 10)
Status
BnH 0AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Panpot: 00H - 40H - 7FH (Left - Center - Right),
Expression (Controller number 11)
Status
BnH 0BH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Expression: 00H - 7FH (0 - 127)
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
2nd byte 3rd byte
Hold 1 (Controller number 64)
Status 2nd byte 3rd byte
BnH 40H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON
* If the HOLD PEDAL Assign parameter is set to HOLD and the Continuous Hold parameter
(SYSTEM/HOLD PEDAL) is set to OFF on the JUNO-Di, only 00H (OFF) or 7FH (ON) can be
transmitted as the value of the control.
Portamento (Controller number 65)
Status
BnH 41H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127) 0 - 63 = OFF, 64 - 127 = ON
2nd byte 3rd byte
Resonance (Controller number 71)
Status
BnH 47H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv= Resonance value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
2nd byte 3rd byte
Release Time (Controller number 72)
Status
BnH 48H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Release Time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
2nd byte 3rd byte
Attack time (Controller number 73)
Status
BnH 49H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Attack time value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
2nd byte 3rd byte
Cutoff (Controller number 74)
Status
BnH 4AH vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Cutoff value (relative change): 00H - 40H - 7FH (-64 - 0 - +63)
2nd byte 3rd byte
General Purpose Controller 5 (Controller number 80)
Status
BnH 50H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
2nd byte 3rd byte
General Purpose Controller 6 (Controller number 81)
Status
BnH 51H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
2nd byte 3rd byte
General Purpose Controller 7 (Controller number 82)
Status
BnH 52H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
2nd byte 3rd byte
General Purpose Controller 8 (Controller number 83)
Status
BnH 53H vvH
n = MIDI channel number: 0H - FH (ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
2nd byte 3rd byte
Portamento control (Controller number 84)
Status
BnH 54H kkH
n = MIDI channel number: 0H - FH (ch.1 - 16)
kk = source note number: 00H - 7FH (0 - 127)
2nd byte 3rd byte
8
Loading...