Roland F701 Assembling guide
1
2
3
1
2
3
12
11
6
1234567
8
91011
12
7
8
9
10
1
4
5
2
3
* 5 1 0 0 0 7 3 1 5 4 - 0 1 *
1
Assembling the F701
To assemble this product correctly, carefully read these instructions before assembly. Keep these instructions nearby so that you can immediately refer
to them when necessary.
Caution when assembling the unit
• Make sure that another person is on hand to help with the assembly and setup.
• Lift the piano carefully—all the while keeping it level.
• Prepare an area in which you can perform the assembly safely.
• If necessary, spread out a blanket or similar material to prevent the piano or oor from being scratched during assembly.
• Place the unit at a location that is level and sure to remain stable. The unit must never be placed on top of deep-pile carpet. Otherwise, you risk causing
damage to the pedals due to instability and unnecessary movement.
• Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won’t accidentally get
swallowed.
• Be very careful, when you assemble and move the piano, to make sure that you do not drop it on your hands or feet.
• Do not use a power tool (e.g., an electric screwdriver) to assemble the piano. You risk damaging or stripping the screws.
• All screws should be tightened provisionally rst, then tightened later. To tighten a screw provisionally, screw it in until about half of its length is no longer
visible. For a successful assembly, compensate for any warping while you tighten the screws.
• Be careful not to pinch the pedal cord during assembly.
• Do not place the piano main unit directly on the oor. Doing so will damage the bottom panel case and the connectors on the bottom of the piano main unit.
Check the Parts
Piano main unit
Side board (left)
Side board (right)
Rear board
Pedal board
Screws (6 x 18 mm): 6 pcs.
Screws (5 x 20 mm): 6 pcs.
Screws (4 x 14 mm): 6 pcs.
Screws (4 x 16 mm): 2 pcs.
Stabilizers (left/right)
Cord clamp: 2 pcs.
Headphone hook: 1 pc.
5. Attach the side board (right)
3
and side board (left)2 to the piano
main unit, and use the screws 6 to fasten them provisionally.
Screws 6: use four screws
If you nd that it’s hard to get the screws to enter their holes, try
pushing the piano in the direction shown by the arrow; you should
then be able to fasten the screws.
6. Attach the rear board
4
to the side boards, and use the screws 7
to fasten it provisionally.
Avoid scratches!
Screws 7:
use six screws
7. Place the unit upright, and attach the stabilizers to the side boards.
* Securely fasten the stabilizers to their nal tightness at this time.
9. Securely tighten each screw (twelve locations) in the order of the side
boards, rear board, and pedal board.
Do not allow a
gap between the
side board and the
main unit.
10. Connect the AC adaptor to the DC In jack of the piano main unit, and
connect the pedal cord to the Pedal jack. Attach the cable fastener
(one location) to the bottom of the main unit and the cord clamps
(two locations) to the side board, and use them to secure the pedal
cord and the AC adaptor cord.
Cable fastener
Cord
clamps
1
1. Remove the side board carton, and remove the left and right side
2 3
boards
and the packing material.
2. Place the packing material on the oor as shown in the illustration.
3. Remove the piano main unit
packing material that you placed on the oor.
* When you stand the piano main unit on top of the packing
material, leave in place the protective mat that surrounds the
piano main unit.
1
, and stand it up on top of the
Side board carton
Protective mat
4. Remove the protective mat that surrounds the piano unit, and
spread it out as shown in the illustration.
* Until you connect the pedal cord (step 10), do not remove the
protective sheet that is wrapped around the piano main unit. If
this sheet is removed, the keyboard keyboard cover will open
during assembly, causing danger.
* Do not grasp the keyboard cover when you lift the unit.
Packing
material
Packing
material
Side board
Piano main unit
Stabilizers
Right Left
8. Attach the pedal board
screws 6.
Avoid scratches!
Screws 8:
use six screws
5
, and provisionally fasten it using the
Screws 6:
use two screws
Placing the pedal
board (as seen from
the side)
Pedal board
11. Use screws
9
to fasten the headphone hook12.
Screws 9: use two screws
12. Connect the supplied AC adaptor and power cord.
Power cord
Place the AC adaptor so the side with the indicator faces upwards and
the side with textual information faces downwards. The indicator will
light when you plug the AC adaptor into an AC outlet.
To AC outlet
© 2020 Roland Corporation
Spread out the protective mat
over the packing material
Place the packing material in this
position
Metal parts
When moving or transporting
If you need to move the unit, close the keyboard cover and disconnect the AC
adaptor. With at least one other person helping you, lift the unit horizontally and
carry it, taking care not to pinch your hands or drop the unit on your feet.
Loading...