All rights reserved. No part of this publication may be reproduced in any form without the written permission
of Roland Corporation.
CC-KWS17058924E0
Page 2
Apr. 2014CUBE-STEX
Cautionary Notes
Before beginning the procedure, please read
through this document. The matters described may
differ according to the model.
No User Data
This product cannot save user data. Backing up user data during servicing is
not required.
Part Replacement
When replacing components near the power-supply circuit or a heatgenerating circuit (such as a circuit provided with a heat sink or including a
cement resistor), carry out the procedure according to the instructions with
respect to the part number, direction, and attachment position (mounting so as
to leave an air gap between the component and the circuit board, etc.).
Parts List
A component whose part code is ******** will not be supplied as a service part
because one of the following reasons applies.
• Because it is supplied as an assembled part (under a different part code).
• Because a number of circuit boards are grouped together and supplied as
a single circuit board (under a different part code).
• Because supply is prohibited due to copyright restrictions.
• Because reissuance is restricted.
• Because the part is made to order (at current market price).
• Because it is carried in electronic data on the Roland web site.
• Because it is a package or an accessory irrelevant to the function
maintenance of the main body.
• Because it can be replaced with an article on the market. (battery or etc.)
Circuit Diagram
In the circuit diagram, “NIU” is an abbreviation for “Not in Use,” and
“UnPop” is an abbreviation for “Unpopulated.” They both mean non-mounted
components. The circuit board and circuit board diagram show silk-screened
indications, but no components are mounted.
Specifications
CUBE Street EX: BATTERY POWERED STEREO
AMPLIFIER
Maximum Power Output
50 W (25 W + 25 W)
Nominal Input Level (1 kHz)
MIC/INSTRUMENT INPUT:-50/-10 dBu
MIC/GUITAR INPUT:-10 dBu
LINE IN:-10 dBu
AUDIO IN (i-CUBE LINK):-10 dBu
AUX IN, STEREO LINK IN:-10 dBu
Nominal Output Level (1 kHz)
LINE OUT (L/MONO, R), STEREO LINK OUT (L, R): -10 dBu
Speakers
Woofer: 20 cm (8 inches) x 2
Tweeter: 5 cm (2 inches) x 2
Controls
POWER switch
BATTERY CHECK/MUTE button
OUTPUT POWER switch (ECO, NORMAL, MAX)
[MIC/INSTRUMENT]
SELECT switch (MIC, INST)
VOLUME knob
BASS knob
MIDDLE knob
TREBLE knob
REVERB knob
[MIC/GUITAR]
TUNER button
TYPE switch (A-GUITAR, ACOUSTIC SIM, CLEAN, CRUNCH, LEAD, MIC)
VOLUME knob
BASS knob
MIDDLE knob
TREBLE knob
CHORUS/DELAY knob (CHORUS, DELAY)
REVERB knob
2
[AUDIO IN]
VOLUME knob
[LINE IN]
VOLUME knob
BATTERY CHECK/MUTE button
STEREO LINK/LINE OUT switch
Page 3
Apr. 2014CUBE-STEX
Indicators
POWER
BATTERY
BATTERY CHECK/MUTE
TUNER
Connectors
[MIC/INSTRUMENT]
INPUT jack:Combo type (XLR type, 1/4-inch TRS phone),
balanced
FOOT SW (REVERB) jack: 1/4-inch TRS phone type
[MIC/GUITAR]
INPUT jack: Combo type (XLR type, 1/4-inch TRS phone), unbalanced
4. After all LEDs have lighted up and then flashed once, within 2 seconds,
depress first the ring section and then the tip section of the foot switch.
All LEDs flash rapidly several times, then the three LEDs at the center of
the panel indicate the software version, as described below.
* In this document, the three LEDs at the center of the panel are called LEFT,
CENTER, and RIGHT.
fig.tuner-led.eps
FS-5U
fig.FS-6.eps
FS-6
• Foot-switch connection cable (PCS-31 or PCS-33)
Procedure
1. Connect a foot switch to the FOOT SW MIC/GUITAR jack.
* If you’re using a PCS-31 cable, white is for tip and red is for ring. If you’re
using a PCS-33 cable, the pedal connected to B on the FS-6 is for tip and the
pedal connected to A is for ring. Also check the panel indication on the FS-6.
2. Make the following settings on the main unit.
• POWER:OFF
• INPUT SELECT:MIC
• OUTPUT POWER: ECO
• STEREO LINK:Left side (LINE OUT side)
• All controls:Minimum
(Turn the controls all the way counterclockwise.)
3. Hold down the ring section of the foot switch connected to the FOOT SW
MIC/GUITAR jack and switch on the power.
All LEDs light up.
* Continue to hold down the foot switch.
VersionLEFTCENTERRIGHT
1.00*--
1.01-*-
1.02--*
1.03**-
1.04*-*
1.05-**
*: flashes, -: goes off
5. Switch off the power to the unit.
Test Mode
Items Required
• Foot switch (FS-5U x 2 or FS-6 x 1)
• Foot-switch connection cable (PCS-31 or PCS-33)
• 1/4-inch phone plug
• Miniature stereo phone plug
Entering the Test Mode
1. Go to Verifying the Version (p. 23) and execute steps 1 through 4.
2. Depress the tip section of the foot switch connected to the FOOT SW
MIC/GUITAR jack to enter the first test item, DSP/EEPROM Test (p. 24).
Quitting the Test Mode
Switch off the power.
Skipping Test Items
Test items cannot be skipped.
23
Page 24
Apr. 2014CUBE-STEX
DSP/EEPROM Test
When the unit enters the Test Mode, DSP and EEPROM Test starts automatically.
The three LEDs at the center of the panel light up in the sequence of LEFT→CENTER→RIGHT to indicate the progress of the testing, then go dark in this
sequence of LEFT→CENTER→RIGHT.
If the test result is OK, testing is completed in a very brief time, and the LEDs are automatically initialized for the following Switch and LED Test (p. 24).
If the test result is NG (not OK), one of the LEDs shown in the table below lights up to indicate the corresponding device where the problem occurred.
* If the test result is NG (not OK), execution cannot advance to the next test item.
Switch and LED Test
Carry out operations in the sequence shown in the table below and verify the status of the corresponding LEDs.
* If an error is made in the order of operations, or of a test is failed, execution cannot advance to the next operation.
* When operating the OUTPUT POWER switch, make a definite stop at each position. If the switch is moved too rapidly, without sufficient stopping, its operation might be
ignored.
In this case, return the switch to its original position and redo the operation.
OperationTUNERLEFTCENTERRIGHTCHECK
Initial stateo*oooooo
Slide the switch, press/release the buttons.
1Set INPUT SELECT to INST.*-oooooo
2Press TUNER.*--ooooo
3Press TUNER again.----*ooo
4Press and hold CHECK/MUTE.----oooo
5Release CHECK/MUTE.-----*oo
6Set OUTPUT POWER to NORMAL.------*o
7Set OUTPUT POWER to MAX.-------*
8Set LINE OUT MODE to STEREO LINK.oooo*ooo
Insert a 1/4-inch phone plug/pull out, depress a pedal.
9Insert into PHONES.oooooooo
10Pull out from PHONES.oooo-*oo
11Insert into AUX IN.oooo-ooo
12Pull out from AUX IN.oooo--*o
13Insert into LINE OUT R.oooo--oo
14Pull out from LINE OUT R.oooo---*
15Insert into LINE OUT L.oooo---o
16Pull out from LINE OUT L.ooo*----
Insert a foot switch/pull out, depress a foot switch.
17Pull out from FOOT SW MIC/GUITAR.oo*----18Insert into FOOT SW MIC/INST.o*o----19Press and hold FOOT SW MIC/INST TIP.ooo----20Release FOOT SW MIC/INST TIP.*-o----21Press and hold FOOT SW MIC/INST RING.o-o----22Release FOOT SW MIC/INST RING.--*----23Pull out from FOOT SW MIC/INST.-----***
LED
FULLHALFLOW
/MUTE
Insert a miniature stereo phone plug.
24Insert into AUDIO IN.-----ooo
o: lights, *: flashes, -: goes off
Pulling out the plug from AUDIO IN makes execution advance automatically to the next test item.
24
Page 25
Apr. 2014CUBE-STEX
RCA pin jack
AUDIO IN L ch
AUDIO IN R ch
i-CUBE LINK out
1k ohm
i-CUBE LINK out
GND
AUDIO IN R ch
AUDIO IN L ch
RCA pin plug
Test of Volume Control with Notch
Turn the AMPLIFIER volume control with notch at the center of the
panel slowly and verify the reading of LEFT and RIGHT LEDs display.
* If the control is turned either too fast or in the opposite direction, the LED flashes
rapidly. If this happens, return it to the original position and redo the operation.
When the control has been turned all the way to the end, execution
automatically advances to the next test item and LEFT, CENTER and
RIGHT LEDs light up.
Volume Control Test
Operate the following controls of (1)-(12) minimum-center-maximum in
numerical order and confirm the all controls work correctly with its LED
lighting and sound from the speaker.
* Operation out of sequence is ignored.
* After detecting all of the minimum, center and the maximum value, test
program advances to test of the next control.
(1) MIC/INSTRUMENT EQUALIZER BASS
(2) MIC/INSTRUMENT EQUALIZER MIDDLE
(3) MIC/INSTRUMENT EQUALIZER TREBLE
(4) MIC/INSTRUMENT REVERB
(5) MIC/GUITAR EQUALIZER BASS
(6) MIC/GUITAR EQUALIZER MIDDLE
(7) MIC/GUITAR EQUALIZER TREBLE
(8) MIC/GUITAR CHORUS/DELAY
(9) MIC/GUITAR REVERB
(10) AUDIO IN VOLUME
(11) LINE IN VOLUME
(12) AMPLIFIER VOLUME
Input/Output Level Test
(for Reference)
When components on the circuit board have been replaced, perform this
test.
Items Required
• Level meter
• Signal generator
• Dummy load resistor tool
-4 Ω load resistor
- 1/4-inch phone plug with 47 kΩ load resister
- 1/4-inch stereo phone plug with 100 Ω load resistor
- i-CUBE LINK input/output tool
fig.i-cube-link-jig.eps
Procedure
1. Switch on the power and start the unit in the normal usage state.
2. Make the following settings on the main unit.
Controls and switchesControls and switches position
MIC INSTRUMENT BASS/
MIDDLE/TREBLE, MIC GUITAR
BASS/MIDDLE/TREBLE
MIC INSTRUMENT REVERB,
MIC/GUITAR CHORUS/DELAY,
REVERB
AUDIO IN VOLUME, INPUT
VOLUME, AMPLIFIER VOLUME,
LINE IN VOLUME
OUTPUT POWERNORMAL
LINE OUT MODESTEREO LINK
Center
0
Center
Control positionLEFTCENTERRIGHT
Minimum
(all the way counterclockwise)
CenterooMaximum
(all the way clockwise)
o: lights, -: goes off
The volume level of the speaker sound increases as the control is
operated toward the maximum position, and the pitch rises at the
intermediate position.
When all volume testing has ended, the LEFT, CENTER, RIGHT and
FULL, HALF, LOW LEDs flash.
o--
ooo
Switch off the power.
This ends the Test Mode.
Verifying Speaker Output
1. Connect a noise meter and a 4 Ω load resistor to the speaker lines.
2. Set the INPUT SELECT switch to MIC.
3. Connect the signal generator to the MIC/LINE CHANNEL INPUT jack
(unbalanced) and input the following signals.
1-kHz sine wave at -26.0 dBm
4. Verify that signals like the following are output from the speaker lines.
SP OUT L: +15.0 ±1.5 dBm
SP OUT R: +15.0 ±1.5 dBm
5. Set the INPUT SELECT switch to INST.
6. Input the following signals to the MIC/INSTRUMENT INPUT jack.
1-kHz sine wave at +5.5 dBm
7. Verify that signals like the following are output from the speaker lines.
SP OUT L: +15.0 ±1.5 dBm
SP OUT R: +15.0 ±1.5 dBm
25
Page 26
Apr. 2014CUBE-STEX
8. Set the AMPLIFIER type switch to MIC.
9. Connect the signal generator to the MIC/GUITAR INPUT jack
(unbalanced) and input the following signals.
1-kHz sine wave at -35.0 dBm
10. Verify that signals like the following are output from the speaker lines.
SP OUT L: +6.8 ±1.5 dBm
SP OUT R: +6.8 ±1.5 dBm
11. Set the AMPLIFIER type switch to CLEAN.
12. Input the following signals to the MIC/GUITAR INPU jack.
1-kHz sine wave at -20.0 dBm
13. Verify that signals like the following are output from the speaker lines.
SP OUT L: +15.3 ±1.5 dBm
SP OUT R: +15.3 ±1.5 dBm
14. Connect the signal generator to the AUX IN jack (monaural) and input the
following signals.
1-kHz sine wave at -3.0 dBm
15. Verify that signals like the following are output from the speaker lines.
SP OUT L: +15.1 ±1.5 dBm
SP OUT R: +15.1 ±1.5 dBm
16. Connect the i-CUBE LINK input/output tool to the i-CUBE LINK jack.
17. Connect the signal generator to the AUDIO IN L jack on the i-CUBE
LINK input/output tool and input the following signals.
1-kHz sine wave at -6.0 dBm
18. Verify that signals like the following are output from the speaker lines.
SP OUT L: +15.2 ±1.5 dBm
19. Connect the signal generator to the AUDIO IN R jack on the i-CUBE
LINK input/output tool and input the following signals.
1-kHz sine wave at -6.0 dBm
20. Verify that signals like the following are output from the speaker lines.
SP OUT R: +15.2 ±1.5 dBm
21. Connect the signal generator to the LINE IN L/MONO jack and input the
following signals.
1-kHz sine wave at -8.0 dBm
22. Verify that signals like the following are output from the speaker lines.
SP OUT L: +14.7 ±1.5 dBm
23. Connect the signal generator to the LINE IN R jack and input the
following signals.
1-kHz sine wave at -8.0 dBm
24. Verify that signals like the following are output from the speaker lines.
SP OUT R: +14.7 ±1.5 dBm
LINE OUT Verification
1. Connect the noise meter and the 1/4-inch phone plug with 47 kΩ load
resister to the LINE OUT L/MONO jack.
2. Connect the signal generator to the LINE IN L/MONO jack and input the
following signals.
1-kHz sine wave at +2.5 dBm
3. Verify that signals like the following are output from the LINE OUT L/
MONO jacks.
LINE OUT L/MONO: +8.0 ±1.5 dBm
4. Connect the 1/4-inch phone plug with 47 kΩ load resister to the LINE
OUT R jack.
5. Connect the signal generator to the LINE IN R jack and input the
following signals.
1-kHz sine wave at -2.5 dBm
6. Verify that signals like the following are output from the LINE OUT R
jack.
LINE OUT R: +8.0 ±1.5 dBm
i-CUBE LINK Verification
1. Connect the noise meter to the i-CUBE LINK OUT jack (with 1 kΩ load
resistor) on the i-CUBE LINK input/output tool.
2. Connect the signal generator to the LINE IN L/MONO jack and input the
following signals.
1-kHz sine wave at -19.0 dBm
3. Verify that signals like the following are output from the i-CUBE LINK
OUT jack on the i-CUBE LINK input/output tool.
i-CUBE LINK: -45.5 ±1.5 dBm
PHONES Verification
1. Connect the noise meter and the 1/4-inch stereo phone plug with 100 Ω
load resistor to the PHONES jack.
2. Connect the signal generator to the LINE IN L/MONO jack and input the
following signals.
1-kHz sine wave at -9.5 dBm
3. Verify that signals like the following are output from the PHONES jack
(L).
PHONES L: +2.5 ±1.5 dBm
4. Connect the signal generator to the LINE IN R jack and input the
following signals.
1-kHz sine wave at -9.5 dBm
5. Verify that signals like the following are output from the PHONES jack
(R).
PHONES R: +2.5 ±1.5 dBm
26
Page 27
Apr. 2014CUBE-STEX
27
Page 28
Apr. 2014CUBE-STEX
Circuit Board (Main, Audio Input, Input Board)
fig.b-main-1.eps
28
Page 29
Apr. 2014CUBE-STEX
fig.b-main-2.eps
29
Page 30
Apr. 2014CUBE-STEX
Circuit Diagram (Main Board: 1/4)
fig.d-main-1.eps@L
REF
TC74VHC4052AFK(E.K)
MPX_B
MPX_A
C231
150pF
DGND
DGND
B7B-PH-K-S (LF)(SN)
C232
150pF
TP8 TP9 TP10
1
2
3
4
5
6
7
CN10
TP73
REF+3.3V
10uFC195
10V
0.1uFC194
IC25
9
B
10
A
6
INH
REF
DGND
TP11 TP12 TP13
PVDD+12V
R24
33k
R33
10k
DGND
16
3
YCOM
VCC
4
3Y
2
2Y
5
1Y
1
0Y
13
XCOM
11
3X
15
2X
14
1X
12
0X
GND
GND
EQ_HIGH
7
8
EQ_MID
EQ_BASS
INPUT_SELECT
FOOTSW_SENSE1
FOOTSW_SENSE2
D+3.3V
R25
R26
22k
22k
1005
1005
2mm pitch
D+3.3V
1SS362FV(TPL3)
DGND
R28
R27
22k
22k
1005
1005
2
D30
3
1
REF
D+3.3V D+3.3V
2
D5
3
1
1SS362FV(TPL3)
DGND
R22
1k
R23
1k
1k
R17
1k
R18
TP30
TP29
TP27
TP28
TP31
TP26
FOR UPDATE
CN1
B6B-PH-K-S (LF)(SN)
6
TP67
TP68
TP69
TP70
TP71
TP72
D+3.3V
C12
0.1uF
DGND
DGND
D+3.3V
2
PVCC
1
1SS362FV(TPL3)
R84
82k
DGND
R78
10k
DGND
LINE_IN_VOLUME
R210
10k
1005
D+3.3V
1SS362FV(TPL3)
2
D6
3
1
C54
1000pF
R211
DGND
AUDIO_IN_VOLUME
REF+3.3V
D+3.3V
1SS362FV(TPL3)
2
D7
3
1
DGNDDGND
C55
1000pF
D+3.3V
MODE_SW
2
1
DGND
C53
1000pF
UnPop
22k
12345
R205
R206
R207
R208
D11
3
VOL1
VOL0
D8
1SS362FV(TPL3)
3
DGNDDGNDDGNDDGND
UnPop
C200
0.1uF
DGND
SOUND_E_TX
SOUND_E_RX
D+3.3V
UnPop
DGND
47
47
47
47
P35
C3
0.1uF
C56
1000pF
2
1
D4
0.1uF
D+3.3V
D+3.3V
2
2
D1
3
3
UnPop
UnPop
1
1
DGND
DGND
TP53
D+3.3V
C5
DGND
RESET1
100
RA4
54
6
3
27
18
54
6
3
27
18
100
RA6
0.01uF
1005
C52
0.01uF
1005
IC4
S-80130ANMC-JCPT2G
5
VDD
OUT
2
VSS
NC
DS
1
DGND
PVDD+12V
Q41 UnPop
2SD1664T100R(PB FREE)
UnPop
R9
5.6k
DGND
D32
UnPop
UDZS TE-17 6.8B
1k
UnPop
D3
3
2mm pitch
R21
47
UnPop
C51
C50
0.01uF
1005
4
3
10uFC278
16V
DGND
R232
D+3.3V
UnPop
DGND
DGND
C38
0.01uF
1005
0.01uF
D+3.3V
R14
22k
1005
32
1
UnPop
0.1uF
DGNDDGND
D2
2
1
SDA
0.01uF
C39
1005
0.1uF
DGND
R228
UnPop
C277
UnPop
3
R15
1.2k
1005
SCL
TP1TP2TP3TP4TP5TP6TP7
47kR12
R126
DGND
REF
C40
C42
0.01uF
1005
1005
C41
0.01uF
1005
DSX321G 16.9344MHZ
UnPop 0
R129
RESET1
RESET
RESET
C281
C276
100uF
16V
UnPop
UnPop
DGND
1k
1.2k R16
1.2k
1005
1005
RA1
D+3.3V
R142
0
10uFC4510V
0
D+1.5V
C43
10uF
10V
DGND
X1
DGND
100R11005
DGND
SOUND_E_TX
SOUND_E_RX
AD2
DA2
MCLK
BCLK
LRCK
DA3
AD4
AD3
56pF
R290
22
22R42
TC7W08FU(TE12L.F)
R13
DGND
C44
10uF
10V
R289
UnPop
EXB28V470JX
18
27
6543
REF+3.3V
C34
0.1uF
REF
C33
0.1uF
C49
15pF
1
1005
2.7k
2
4
3
C36
15pF
1005
DGND
C48
1000pF
R260
UnPop1k
R212
UnPop1k
R61005
100
220R4
UnPop
220R8
100
R31005
100R2291005
100
R21005
C37
DGND
UnPop
UnPop
UnPop
RB160M-40TR
3
1
2
DGND
IC1
7
8
3
E2
VCC
2
E1
1
E0
5
SDA
6
SCL
7
_WC
VSS
IC2
M24512-RMN6TP
4
D+3.3V
DGND
DGND
47
47R256
79
80
102
103
104
105
106
84
85
95
94
93
92
91
90
89
88
87
86
134
133
139
2.7k
R20
140
1005
98
99
135
136
137
142
143
81
70
71
74
75
76
77
119
1005
118
110
111
107
112
113
116
117
1005
UnPop
1
D31
2
SSM3K119TU(TE85L)
UnPop
Q37
D+3.3V
R19
22k
1005
1
2
EEPROM+3.3V
0.1uFC14
0.1uFC13
0.1uFC15
0.1uFC16
0.1uFC17
0.1uFC18
0.1uFC19
0.1uFC20
WP_EEPROM
RESET
5
3
6
IC1
TC7W08FU(TE12L.F)
C8
0.1uF
C9
0.1uF
0.1uFC21
0.1uFC22
0.1uFC24
0.1uFC27
0.1uFC23
0.1uF
0.1uFC26
C25
9
34
26
17
826149
96
UPD800402GJ-211-UEN-A(ESC)
10
18273550628397
1
114
122
IC5
132
144
115
1233742
55
41
36
73
DGND
B2B-PH-SM4-TB (LF)(SN)CN15
UnPop
B2B-PH-SM4-TB (LF)(SN)CN15
RESET
D+3.3V
VCC
GND
DGND
AUDIO_IN_JACK
0.1uF
0.1uFC30
0.1uFC29
0.1uFC28
C31
DGND
72
141
108
101
100
138
109
D+3.3V
8
IC1
TC7W08FU(TE12L.F)
4
D+3.3V
C196
0.1uF
R141
22k
R186
1k
D+1.5V
C46
10uF
10V
AD1
DGND
121
68
69
124
125
126
127
128
129
130
131
53
54
56
57
58
59
60
63
43
44
45
46
47
48
51
52
64
65
66
67
120
78
22
24
21
28
23
25
29
31
33
39
40
38
32
30
2
3
4
5
6
7
8
11
20
19
16
14
13
12
15
DGND
30
Page 31
Apr. 2014CUBE-STEX
fig.d-main-1.eps@R
TP15
TP17
TP16
TP18
TP14
REF+3.3V
1
VOL1
VOL0
TP78
2
3
4
5
6
CN19
B6B-PH-K-S (LF)(SN)
PANEL BOARD L
MPX_A
MPX_B
C279
150pF
UnPop
DGND DGND
C280
150pF
UnPop
REF
47R193
R265
47
R2661005
1005
R187
1k
0.01uFC250
6543
RA5
27
YC164-JR-0747RL
18
47
R209
47
R263
47
R264
47
R127
R128
47
PDN_CODEC2
PDN_CODEC
22k
SW_TUNER
DGND
WP_EEPROM
MPX_A
MPX_B
R278
100
1005
SELECT_MIC_OR_INST
D+3.3V
R123
22k
1005
LED_TUNER_L
SW_CHECK
1005
1kR272
0.01uFC269
LED_TUNER_R
R5
100
1005
P35
RA3
YC164-JR-0710KL
6543
27
18
6543
27
18
RA2
YC164-JR-0710KL
C201
0.1uF
MODSEL
1005
2.2kR269
1005
2.2kR100
1005
2.2kR270
C274
C275
C202
0.1uF
0.1uF
0.1uF
DGND
1005
2.2kR191
1005
2.2kR192
1005
2.2kR195
C47
C268
C203
0.1uF
0.1uF
0.1uF
DGND
DGND
MUTE_CONTROL
LED_TUNER
DGND
DA1
D+3.3V
DGND
C219
0.01uF
DGND
DGND
D+3.3V
R90
22k
1005
D+3.3V
R190
22k
1005
D+3.3V
Q31
DTA114EMT2L
1
STB
32
R107
56k
Q29
DTC144EMT2L
1
23
DGND
LED_TUNER
LED_TUNER_R
LED_TUNER_C
LED_TUNER_L
D+3.3V
R44
22k
1005
R108
1k
1005
1005
UnPop
R267
R268
22k
22k
1005
1005
FOOTSW_SENSE1
FOOTSW_SENSE2
LINK_MODE
R125
R124
22k
22k
1005
1005
LINK_IN
LINK_OUT_R
LINK_OUT_L
1
R259
1k
D+3.3V
SW_CHECK
SW_TUNER
1kR280
1kR93
POWER_SW_SENSE
ADAPTOR_SENSE
PHONES_SENSE
D+3.3V
Q32
DTA114EMT2L
ENB_ON
32
R45
56k
DGND
D+3.3V
Q28
2SA1586SU-GR.LF(D
23
R274
47k
1
R276
22k
D+3.3V
R277
22k
EQ_HIGH
EQ_MID
EQ_BASS
1
DGND
D+3.3V
Q39
DTA114EMT2L
1
HEADPHONE_SD
32
R7
56k
DGND
TP76
REF+3.3V
MODE_SW
LINE_IN_VOLUME
LED_VCC
LED_POWER
LED_LOW
LED_HALF
LED_FULL
LED_CHECK
REF
TP77
TP38TP39TP40
TP41
DGND
TP37
TP75
TP36
TP74
MIC_GT_GAIN
Q22
DTC144EMT2L
23
TP24
TP23
TP33
TP34
TP22
TP32
TP25
TP35
D+3.3V
Q33
DTA114EMT2L
1
32
R198
56k
DGND
1
TP19TP20
1
2
3
4
5
6
7
8
9
10
11
CN14
B11B-PH-K-S (LF)(SN)
TP21
C142
0.1uF
1
2
3
4
5
6
7
PANEL BOARD L
8
9
10
CN18
B10B-PH-K-S (LF)(SN)
AMP_POWER
D+3.3V
2
Q34
DTA114EMT2L
3
AMP_MUTE
PANEL BOARD R
DGND
MODE SETTING
EA7/H: CLOCK 15-20MHz , L: 12-15MHz
EA6/H: EEPROM program mode, L: Normal mode