Roland C-380 User Manual
IMPORTANT SAFETY INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
WARNING:
IMPORTANT:
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
THIS APPARATUS MUST BE EARTHED
THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
For the U.K.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS”, “USING THE UNIT
SAFELY” (p. 4), and “IMPORTANT NOTES” (p. 6). These sections provide important information concerning the proper
operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature
provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on
hand as a convenient reference.
All rights reserved. No part of this publication may be reproduced in
any form without the written permission of ROLAND CORPORATION.
Copyright © 2010 ROLAND CORPORATION
USING THE UNIT SAFELY
About WARNING and CAUTION Notices
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
ALWAYS OBSERVE THE FOLLOWING
•
Connect mains plug of this model to a mains socket
outlet with a protective earthing connection.
..................................................................................................................................
•
Do not open or perform any internal modifications on
the unit.
..................................................................................................................................
•
Do not attempt to repair the unit, or replace parts
within it (except when this manual provides specific
instructions directing you to do so). Refer all servicing
to your retailer, the nearest Roland Service Center, or
an authorized Roland distributor, as listed on the
“Information” page.
..................................................................................................................................
• Never install the unit in any of the following locations.
• Subject to temperature extremes (e.g., direct
sunlight in an enclosed vehicle, near a heating
duct, on top of heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet floors); or
are
• Exposed to steam or smoke; or are
• Subject to salt exposure; or are
• Humid; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and shakiness.
..................................................................................................................................
•
Make sure you always have the unit, pedalboard or the
bench placed so it is level and sure to remain stable.
Never place it on stands that could wobble, or on
inclined surfaces.
..................................................................................................................................
• The unit should be connected to a power supply only
of the type described in the operating instructions, or
as marked on the rear side of unit.
About the Symbols
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
•
Use only the attached power-supply cord. Also, the
supplied power cord must not be used with any other
device.
..................................................................................................................................
• Do not excessively twist or bend the power cord, nor
place heavy objects on it. Doing so can damage the
cord, producing severed elements and short circuits.
Damaged cords are fire and shock hazards!
..................................................................................................................................
•
This unit, either alone or in combination with an
amplifier and headphones or speakers, may be
capable of producing sound levels that could cause
permanent hearing loss. Do not operate for a long
period of time at a high volume level, or at a level that
is uncomfortable. If you experience any hearing loss or
ringing in the ears, you should immediately stop using
the unit, and consult an audiologist.
..................................................................................................................................
•
Do not allow any objects (e.g., flammable material,
coins, pins); or liquids of any kind (water, soft drinks,
etc.) to penetrate the unit.
..................................................................................................................................
• Protect the unit from strong impact.
(Do not drop it!)
..................................................................................................................................
..................................................................................................................................
4
USING THE UNIT SAFELY
Immediately turn the power off, remove the power
•
cord from the outlet, and request servicing by your
retailer, the nearest Roland Service Center, or an
authorized Roland distributor, as listed on the
“Information” page when:
• The power-supply cord or the plug has been
damaged; or
• If smoke or unusual odor occurs
• Objects have fallen into, or liquid has been spilled
onto the unit; or
• The unit has been exposed to rain (or otherwise
has become wet); or
• The unit does not appear to operate normally or
exhibits a marked change in performance.
..................................................................................................................................
In households with small children, an adult should
•
provide supervision until the child is capable of
following all the rules essential for the safe operation
of the unit.
..................................................................................................................................
Do not force the unit’s power-supply cord to share an
•
outlet with an unreasonable number of other devices.
Be especially careful when using extension cords—the
total power used by all devices you have connected to
the extension cord’s outlet must never exceed the
power rating (watts/amperes) for the extension cord.
Excessive loads can cause the insulation on the cord to
heat up and eventually melt through.
..................................................................................................................................
Before using the unit in a foreign country, consult
•
with your retailer, the nearest Roland Service Center,
or an authorized Roland distributor, as listed on the
“Information” page.
..................................................................................................................................
Do not put anything that contains water (e.g., flower
•
vases) on this unit. Also, avoid the use of insecticides,
perfumes, alcohol, nail polish, spray cans, etc., near
the unit. Swiftly wipe away any liquid that spills on the
unit using a dry, soft cloth.
• The unit should be located so that its location or
position does not interfere with its proper ventilation.
..................................................................................................................................
Always grasp only the plug on the power-supply cord
•
when plugging into, or unplugging from, an outlet or
this unit.
..................................................................................................................................
At regular intervals, you should unplug the power plug
•
and clean it by using a dry cloth to wipe all dust and
other accumulations away from its prongs. Also,
disconnect the power plug from the power outlet
whenever the unit is to remain unused for an extended
period of time. Any accumulation of dust between the
power plug and the power outlet can result in poor
insulation and lead to fire.
..................................................................................................................................
Try to prevent cords and cables from becoming
•
entangled. Also, all cords and cables should be placed
so they are out of the reach of children.
..................................................................................................................................
Never climb on top of, nor place heavy objects on the
•
unit.
..................................................................................................................................
Never handle the power cord or its plugs with wet
•
hands when plugging into, or unplugging from, an
outlet or this unit.
..................................................................................................................................
If you need to move the instrument, take note of the
•
precautions listed below. At least two persons are
required to safely lift and move the unit. It should be
handled carefully, all the while keeping it level. Make
sure to have a firm grip, to protect yourself from injury
and the instrument from damage.
• Disconnect the power cord.
• Disconnect all cords coming from external devices,
pedalboard, and satellite speakers.
• Fold down the music stand.
..................................................................................................................................
Before cleaning the unit, turn off the power and
•
unplug the power cord from the outlet (p. 24).
..................................................................................................................................
Whenever you suspect the possibility of lightning in
•
your area, pull the plug on the power cord out of the
outlet.
..................................................................................................................................
(C-380)
•
Be careful when opening/closing the keyboard cover
so you do not get your fingers pinched (p. 22). Adult
supervision is recommended whenever small children
use the unit.
..................................................................................................................................
When using the organ bench, please observe the
•
following points:
• Do not use the organ bench as a toy, or as a
stepping stool.
• Do not allow two or more persons to sit on the
organ bench.
..................................................................................................................................
•
Keep the included screws and keys for keyboard cover
in a safe place out of children’s reach, so there is no
chance of them being swallowed accidentally.
..................................................................................................................................
5
IMPORTANT NOTES
Power Supply
• Do not connect this unit to same electrical outlet that is being used by
an electrical appliance that is controlled by an inverter (such as a
refrigerator, washing machine, microwave oven, or air conditioner), or
that contains a motor. Depending on the way in which the electrical
appliance is used, power supply noise may cause this unit to
malfunction or may produce audible noise. If it is not practical to use a
separate electrical outlet, connect a power supply noise filter
between this unit and the electrical outlet.
• Before connecting this unit to other devices, turn off the power to all
units. This will help prevent malfunctions and/or damage to speakers
or other devices.
• Although the LCD and LEDs are switched off when the POWER switch
is switched off, this does not mean that the unit has been completely
disconnected from the source of power. If you need to turn off the
power completely, first turn off the POWER switch, then unplug the
power cord from the power outlet. For this reason, the outlet into
which you choose to connect the power cord’s plug should be one
that is within easy reach and readily accessible.
Placement
• Using the unit near power amplifiers (or other equipment containing
large power transformers) may induce hum. To alleviate the problem,
change the orientation of this unit; or move it farther away from the
source of interference.
• This device may interfere with radio and television reception. Do not
use this device in the vicinity of such receivers.
• Noise may be produced if wireless communications devices, such as
cell phones, are operated in the vicinity of this unit. Such noise could
occur when receiving or initiating a call, or while conversing. Should
you experience such problems, you should relocate such wireless
devices so they are at a greater distance from this unit, or switch them
off.
• Do not expose the unit to direct sunlight, place it near devices that
radiate heat, leave it inside an enclosed vehicle, or otherwise subject it
to temperature extremes. Also, do not allow lighting devices that
normally are used while their light source is very close to the unit
(such as a piano light), or powerful spotlights to shine upon the same
area of the unit for extended periods of time. Excessive heat can
deform or discolor the unit.
• When moved from one location to another where the temperature
and/or humidity is very different, water droplets (condensation) may
form inside the unit. Damage or malfunction may result if you
attempt to use the unit in this condition. Therefore, before using the
unit, you must allow it to stand for several hours, until the
condensation has completely evaporated.
• Do not allow rubber, vinyl, or similar materials to remain on the unit
for long periods of time. Such objects can discolor or otherwise
harmfully affect the finish.
• Do not allow objects to remain on top of the keyboard or pedal board.
This can be the cause of malfunction, such as keys ceasing to produce
sound.
• Do not paste stickers, decals, or the like to this instrument. Peeling
such matter off the instrument may damage the exterior finish.
Maintenance
• To clean the unit, use a dry, soft cloth; or one that is slightly
dampened. Try to wipe the entire surface using an equal amount of
strength, moving the cloth along with the grain of the wood. Rubbing
too hard in the same area can damage the finish.
• Never use benzine, thinners, alcohol or solvents of any kind, to avoid
the possibility of discoloration and/or deformation.
Repairs and Data
• Please be aware that all data contained in the unit’s memory may be
lost when the unit is sent for repairs. Important data should always be
backed up on a USB memory, or written down on paper (when
possible). During repairs, due care is taken to avoid the loss of data.
However, in certain cases (such as when circuitry related to memory
itself is out of order), we regret that it may not be possible to restore
the data, and Roland assumes no liability concerning such loss of
data.
Before Using USB Memory
Using USB memories
• Use USB memory available from Roland. Proper operation cannot be
guaranteed if other USB device is used.
• We cannot guarantee correct operation if other brands of USB
memory are used. Note that only USB memory keys can be used—
never use any other kind of USB device.
• When connecting USB memory, position it horizontally with the USB
connector and insert it without using excessive force. The USB
MEMORY connector may be damaged if you use excessive force when
inserting USB memory.
• Do not insert anything other than USB memory (e.g., wire, coins, other
types of device) into the USB connector. Doing so will damage the
USB connector.
• Do not apply excessive force to the connected USB memory.
• Carefully insert the USB memory all the way in—until it is firmly in
place.
• Never touch the terminals of the USB memory. Also, avoid getting the
terminals dirty.
• USB memories are constructed using precision components; handle
the USB memories carefully, paying particular note to the following.
• To prevent damage to the USB memories from static electricity, be
sure to discharge any static electricity from your own body before
handling the USB memories.
• Do not touch or allow metal to come into contact with the contact
portion of the USB memories.
• Do not bend, drop, or subject USB memories to strong shock or
vibration.
• Do not keep USB memories in direct sunlight, in closed vehicles, or
other such locations.
• Do not allow USB memories to become wet.
• Do not disassemble or modify the USB memories.
6
Additional Precautions
• Please be aware that the contents of memory can be irretrievably lost
as a result of a malfunction, or the improper operation of the unit. To
protect yourself against the risk of loosing important data, we
recommend that you periodically save a backup copy of important
data you have stored in the unit’s memory on a USB memory.
• Unfortunately, it may be impossible to restore the contents of data
that was stored in the USB memory or unit’s memory once it has been
lost. Roland Corporation assumes no liability concerning such loss of
data.
• Use a reasonable amount of care when using the unit’s buttons,
sliders, or other controls; and when using its jacks and connectors.
Rough handling can lead to malfunctions.
• Never strike or apply strong pressure to the display.
• A small amount of noise may be heard from the display during normal
operation.
• When connecting / disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will avoid causing shorts,
or damage to the cable’s internal elements.
• A small amount of heat will radiate from the unit during normal
operation.
• You should be careful that you don’t disturb your neighbors, since
floors and walls can too easily transmit vibrations (especially
vibrations from the pedalboard). You should be especially careful at
night or when you’re using headphones.
• When you need to transport the unit, pack it in shock-absorbent
material. Transporting the unit without doing so can cause it to
become scratched or damaged, and could lead to malfunction.
• Do not apply undue force to the music stand while it is in use.
• Some connection cables contain resistors. Do not use cables that
incorporate resistors for connecting to this unit. The use of such
cables can cause the sound level to be extremely low, or impossible to
hear. For information on cable specifications, contact the
manufacturer of the cable.
• Due to the way that the indicators for the tablets and pistons are
manufactured, some variances in coloration may occur. This does not
indicate a malfunction.
IMPORTANT NOTES
.......................................................................................................
• MMP (Moore Microprocessor Portfolio) refers to a patent portfolio
concerned with microprocessor architecture, which was developed
by Technology Properties Limited (TPL). Roland has licensed this
technology from the TPL Group.
• Roland is a registered trademark of Roland Corporation in the United
States and/or other countries.
• All product names mentioned in this document are trademarks or
registered trademarks of their respective owners.
.......................................................................................................
7
Contents
IMPORTANT SAFETY INSTRUCTIONS ............................................................3
USING THE UNIT SAFELY ................................................................................4
IMPORTANT NOTES ........................................................................................6
Introduction ................................................................................................. 12
Conventions Used in This Manual.....................................................................................................................................12
Keyboards and Divisions.......................................................................................................................................................12
Names of Things and What They Do .......................................................... 13
Names of Things on the C-380............................................................................................................................................13
Names of Things on the C-330............................................................................................................................................13
Tablets and Pistons (C-380)..................................................................................................................................................14
Tablets and Pistons (C-330)..................................................................................................................................................16
Display and Panel ....................................................................................................................................................................18
External Connectors ...............................................................................................................................................................18
Before You Start Playing ............................................................................. 19
Connecting the Pedalboard ................................................................................................................................................19
Using the Music rest ...............................................................................................................................................................19
Placing the Bench....................................................................................................................................................................19
Installing the Satellite Speakers .........................................................................................................................................20
Attaching to the Main Unit (C-330 Only)...........................................................................................................20
Attaching to the Wall................................................................................................................................................20
Connecting the Satellite Speakers to the Organ............................................................................................21
Opening and Closing the Keyboard Cover (C-380 only) ...........................................................................................22
Locking the Cover......................................................................................................................................................22
Connecting the Power Cord................................................................................................................................................22
Turning the Power On and Off............................................................................................................................................24
Turning On the Power..............................................................................................................................................24
Turning Off the Power..............................................................................................................................................25
Connecting Headphones......................................................................................................................................................25
Connecting the USB memory .............................................................................................................................................26
About the Display....................................................................................................................................................................27
Contents of the Main Screen .................................................................................................................................27
Return to the Main Screen......................................................................................................................................27
Adjusting the Display Contrast.............................................................................................................................27
Listening to the Demo Songs..............................................................................................................................................28
8
Performing ................................................................................................... 29
Playing Various Sounds.........................................................................................................................................................29
Selecting Stops (sounds).........................................................................................................................................29
Selecting a Sound Variation (Voice Palette).....................................................................................................30
Playing the Sounds of Another Division (Couplers)....................................................................................................31
Using a Manual Coupler ..........................................................................................................................................31
Using the Melody Coupler......................................................................................................................................32
Using the Bass Coupler............................................................................................................................................33
Adjusting the Volume and Reverberation......................................................................................................................34
Adjusting the Overall Volume...............................................................................................................................34
Adjusting the Volume of the Satellite Speakers .............................................................................................34
Adjusting the Reverberation .................................................................................................................................34
Changing the Type of Reverberation...............................................................................................................................35
Changing the Room Type.......................................................................................................................................35
Changing the Wall Type ..........................................................................................................................................36
Adding Soft Vibrato (Tremulant) .......................................................................................................................................37
Adding Tremulant to Each Division ....................................................................................................................37
Adjusting the Tremulant Effect.............................................................................................................................37
Changing the Tuning (Temperament).............................................................................................................................38
Using Baroque Pitch...............................................................................................................................................................39
Tuning to Match the Pitch of Another Instrument......................................................................................................40
Transposing the Key...............................................................................................................................................................41
Using the Expression Pedal to Adjust the Volume of the Organ............................................................................42
Specifying the Divisions Affected by the Expression Pedal .......................................................................42
Storing the Division for which the Volume is to be Adjusted ...................................................................43
Setting the Minimum Volume of the Expression Pedal...............................................................................44
Using the Kick Switches.........................................................................................................................................................45
Contents
Storing a Combination of Stops ................................................................. 46
Storing or Recalling a Registration....................................................................................................................................47
Storing a Registration...............................................................................................................................................47
Recalling a Registration ...........................................................................................................................................47
Resetting the Sound Settings (General Cancel) ...........................................................................................................47
Using Memory Banks..............................................................................................................................................................48
Storing the Combination of Memory Pistons as a Memory Bank ............................................................48
Recalling a Registration from a Different Memory Bank .............................................................................49
Recalling Registrations Successively ................................................................................................................................49
Practicing Along with a Preset Song or Performance Data...................... 50
Selecting and Playing Back a Song ...................................................................................................................................50
Muting a Specific Division During Playback ....................................................................................................52
Playing Back a Specific Division as a Guide Tone...........................................................................................53
Changing the Tempo .............................................................................................................................................................54
Using the Metronome............................................................................................................................................................55
Recording Your Performances.................................................................... 56
Recording a Song ....................................................................................................................................................................56
Play Back the Recorded Song..............................................................................................................................................57
Saving a Recorded Song .......................................................................................................................................................57
Deleting a Recorded Song ...................................................................................................................................................59
Copying a Saved Song...........................................................................................................................................................60
9
Contents
Saving and Loading Settings on USB Memory.......................................... 62
Formatting USB Memory ......................................................................................................................................................62
Saving and Loading Memory Banks .................................................................................................................................62
Saving to USB Memory ............................................................................................................................................62
Loading from USB Memory into Internal Memory ........................................................................................63
Deleting a Memory Bank from USB Memory...................................................................................................63
Copying a Memory Bank.......................................................................................................................................................64
Saving and Loading Voice Setup.......................................................................................................................................65
Saving to USB Memory ............................................................................................................................................65
Loading a Voice Setup .............................................................................................................................................66
Deleting a Voice Setup.............................................................................................................................................67
Other Settings.............................................................................................. 68
Settings for the USER/MIDI Couplers................................................................................................................................68
Playing Sounds that are not in the Sound Tablets (USER Sound Coupler)...........................................68
Playing Sounds on an External MIDI Sound Module (MIDI Coupler) ......................................................69
MIDI Settings.............................................................................................................................................................................71
Local Control Setting (Local)..................................................................................................................................71
Specifying the Type of External MIDI Sound Module (Tone Name)........................................................72
Specifying the MIDI Data Output format for the General Memory Pistons (Tx Piston)....................72
Returning all Settings to the Factory-Set State (Factory Reset)..............................................................................72
Storing Your Settings (Customize)....................................................................................................................................73
Connecting External Devices...................................................................... 74
Connecting to Audio Equipment.......................................................................................................................................74
Connecting to Amplified Speakers......................................................................................................................74
Playing the Sounds of an External MIDI Sound Module or an Audio Device.......................................75
Adjusting the Volume of your Audio Device...................................................................................................75
Connecting to MIDI Equipment .........................................................................................................................................76
Using the Organ to Play the Sounds of a MIDI Sound Module .................................................................76
Using V-LINK..............................................................................................................................................................................77
10
List of Preset Song/Demo Song .................................................................. 78
List of Voices (Stops).................................................................................... 79
MAN I Division (Lower Keyboard)......................................................................................................................................79
MAN II Division (Upper Keyboard).....................................................................................................................................79
PEDAL Division (Pedalboard) ..............................................................................................................................................79
USER/MIDI Voice ......................................................................................................................................................................80
Troubleshooting .......................................................................................... 82
Error Messages............................................................................................. 85
List of Shortcuts ........................................................................................... 85
Glossary ........................................................................................................ 86
MIDI Implementation Chart........................................................................ 88
Specifications............................................................................................... 89
Contents
Index ............................................................................................................. 91
11
Introduction
Thank you, and congratulations on your choice of a Roland Classic Organ. The Roland C-380 and C-330 Classic Organs represent a new
type of organ with numerous features, allowing you to enjoy full-fledged pipe organ sound in your home.
In order to take full advantage of your Roland Classic Organ and enjoy trouble-free operation, please read this owner’s manual
carefully.
Conventions Used in This Manual
This owner’s manual uses the following conventions in order to explain operations as clearly as possible.
• The Roland C-380 and C-330 classical organs are referred to as the “C-380” and “C-330,” respectively.
• Tablet and Piston names are enclosed in square brackets (“[ ]”), as in [SET] piston.
• For easier readability, some screens and colors used here may differ somewhat from actual screens and colors.
• Text preceded by a symbol such as or an asterisk (*) are warnings. Please be sure to read these.
• (p. **) refers to pages within the manual.
• Text preceded by explains a shortcut for the operation.
• Perform all operations after you’ve returned to the main screen. For details on how to return to the main screen, refer to “Return to the
Main Screen” (p. 27).
• The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that your
unit may incorporate a newer, enhanced version of the system (e.g., includes newer sounds), so what you actually see in the display may
not always match what appears in the manual.
Keyboards and Divisions
The Roland C-380 and C-330 Classic Organs have two manuals and a pedalboard.
From the bottom, these are referred to as the “PEDAL division,” “MAN I (Manual 1) division,” and “MAN II (manual 2) division.”
The basic group of sounds for each keyboard is called a “division.”
MAN II (Manual 2) division
MAN I (Manual 1) division
PEDAL division
12
Names of Things and What They Do
Music Rest (p. 19)
Tablets (p. 16)
Pistons (p. 17)
Power Switch (p. 24)
USB Connector (p. 26)
Headphone Jack (p. 25)
Organ Bench (p. 19)
Pedalboard (p. 19)
External Connectors (p. 18)
Display/Panel
(p. 18, 27)
AC Inlet (p. 23)
Satellite Speaker Jacks (p. 21)
Names of Things on the C-380
Music Rest (p. 19)
Keyboard Cover (p. 22)
Power Switch (p. 24)
Headphone Jack (p. 25)
Organ Bench (p. 19)
Pedalboard (p. 19)
Tablets (p. 14)
Pistons (p. 15)
Display/Panel
(p. 18, 27)
USB Connector (p. 26)
External Connectors (p. 18)
Satellite Speaker Jacks (p. 21)
AC Inlet (p. 23)
Names of Things on the C-330
13
Names of Things and What They Do
Tablets and Pistons (C-380)
Tablets
These select the basic stops (sounds) of the organ.
➔
“Playing Various Sounds” (p. 29)
1.
PEDAL Division Tablets
These select stops for the PEDAL division.
MAN I Division Tablets
2.
These select stops for the MAN I (manual 1) division.
3.
MAN II Division Tablets
These select stops for the MAN II (manual 2) division.
1 2
11 12
4 7
14
14
13 15
16
Coupler Tablets
These allow a specific division to simultaneously play the sound of
another keyboard.
➔
“Playing the Sounds of Another Division (Couplers)” (p. 31)
7.
PEDAL Division Coupler Tablets
These make the pedalboard play the sounds of the MAN I division
(lower manual) or MAN II division (upper manual).
8.
MAN I Division Coupler Tablet
This makes the lower manual play the sounds of the MAN II division
(upper manual).
USER/MIDI Coupler
These allow you to select sounds that cannot be selected by the
other tablets. You’ll also use these tablets when an external MIDI
device is connected.
➔
“Settings for the USER/MIDI Couplers” (p. 68)
PEDAL Division USER/MIDI Coupler
4.
These select sounds for the PEDAL division (pedalboard).
5.
MAN I Division USER/MIDI Coupler
These select sounds for the MAN I division (lower manual).
6.
MAN II Division USER/MIDI Coupler
These select sounds for the MAN II division (upper manual).
14
Tremulant Tablets
These apply a tremulant effect to the selected sound.
➔
“Adding Soft Vibrato (Tremulant)” (p. 37)
9.
MAN I Division Tremulant Tablet
This applies a tremulant effect to the sound of the MAN I division
(lower manual).
10.
MAN II Division Tremulant Tablet
This applies a tremulant effect to the sound of the MAN II division
(upper manual).
Names of Things and What They Do
8 9
5
18
17 19
Pistons
[SET] Piston
11.
This stores a combination of sounds (registration) to a general
memory piston or a division memory piston.
➔
“Storing a Registration” (p. 47)
General Memory [1]–[5] Pistons
12.
Each of these pistons can store the combination of sounds
(registration) for the entire organ.
➔
“Storing a Registration” (p. 47)
13.
MAN I Division Coupler Piston
This piston causes the lower manual to play the sound of the MAN II
division (upper manual).
It has the same function as the MAN I division coupler tablets (8).
14.
PEDAL Division Coupler Piston
This piston causes the pedalboard to play the sound of the MAN I
division (lower manual) or MAN II division (upper manual).
It has the same function as the PEDAL division coupler tablets (7).
MAN I Division Memory [1]–[5] Pistons
15.
Each of these pistons can store the sound (registration) for the
MAN I division (lower manual.)
➔
“Storing a Registration” (p. 47)
20 22 2421 23 25
3
6 10
18.
Memory Bank Select [M–] Piston/[M+] Piston
Use these pistons to switch memory banks when you want to use
more than six combinations of sounds.
➔
“Recalling a Registration from a Different Memory Bank” (p. 49)
19.
MAN I & PEDAL Enclosed Piston
Turn this piston on if you want to use the expression pedal to adjust
the volume of MAN I division and PEDAL division.
➔
“Specifying the Divisions Affected by the Expression Pedal” (p. 42)
Bass Coupler [BASS] Piston
20.
This causes the lowest note played on the lower manual to be
sounded by the PEDAL division sound.
➔
“Using the Bass Coupler” (p. 33)
Melody Coupler [MEL] Piston
21.
This causes the highest note played on the lower manual to be
sounded by the MAN II division (upper manual) sound.
➔
“Using the Melody Coupler” (p. 32)
[STOP] Piston
22.
This stops playback or recording of a song.
[PLAY/PAUSE] Piston
23.
This starts or pauses playback of a song.
➔
“Practicing Along with a Preset Song or Performance Data” (p. 50)
MAN II Division Memory [1]–[5] Pistons
16.
Each of these pistons can store the sound (registration) for the
MAN II division (upper manual).
➔
“Storing a Registration” (p. 47)
[PREV] Piston/[NEXT] Piston
17.
These successively load the registration stored at the previous or
next general memory piston; e.g., 3 → 2 → 1 ([PREV] piston) or 1→ 2
→
3 ([NEXT] piston).
➔
“Recalling Registrations Successively” (p. 49)
24.
[REC] Piston
Use this when you want to record your playing.
➔
“Recording Your Performances” (p. 56)
25.
General Cancel [0] Piston
This sets the organ to the condition in which all tablets and couplers
are cancelled, so that no sounds are selected.
It’s convenient to use this piston when you want to specify a
combination of sounds from scratch.
➔
“Resetting the Sound Settings (General Cancel)” (p. 47)
15
Names of Things and What They Do
Tablets and Pistons (C-330)
Tablets
These select the basic stops (sounds) of the organ.
➔
“Playing Various Sounds” (p. 29)
1.
PEDAL Division Tablets
These select stops for the PEDAL division.
MAN I Division Tablets
2.
These select stops for the MAN I (manual 1) division.
3.
MAN II Division Tablets
These select stops for the MAN II (manual 2) division.
1 2
4 7
11 12 13
Coupler Tablets
These allow a specific division to simultaneously play the sound of
another keyboard.
➔
“Playing the Sounds of Another Division (Couplers)” (p. 31)
7.
PEDAL Division Coupler Tablets
These make the pedalboard play the sounds of the MAN I division
(lower manual) or MAN II division (upper manual.)
8.
MAN I Division Coupler Tablet
This makes the lower manual play the sounds of the MAN II division
(upper manual.)
USER/MIDI Coupler
These allow you to select sounds that cannot be selected by the
other tablets. You’ll also use these tablets when an external MIDI
device is connected.
➔
“Settings for the USER/MIDI Couplers” (p. 68)
PEDAL Division USER/MIDI Coupler
4.
These select sounds for the PEDAL division (pedalboard.)
5.
MAN I Division USER/MIDI Coupler
These select sounds for the MAN I division (lower manual.)
6.
MAN II Division USER/MIDI Coupler
These select sounds for the MAN II division (upper manual.)
16
Tremulant Tablets
These apply a tremulant effect to the selected sound.
➔
“Adding Soft Vibrato (Tremulant)” (p. 37)
9.
MAN I Division Tremulant Tablet
This applies a tremulant effect to the sound of the MAN I division
(lower manual.)
10.
MAN II Division Tremulant Tablet
This applies a tremulant effect to the sound of the MAN II division
(upper manual.)
Names of Things and What They Do
5 8 9 6 10
3
15 17 1914 16 18 20
Pistons
[SET] Piston
11.
This stores a combination of sounds (registration) to a general
memory piston.
➔
“Storing a Registration” (p. 47)
Melody Coupler [MEL] Piston
16.
This causes the highest note played on the lower manual to be
sounded by the MAN II division (upper manual) sound.
➔
“Using the Melody Coupler” (p. 32)
12.
General Memory [1]–[5] Pistons
Each of these pistons can store the combination of sounds
(registration) for the entire organ.
➔
“Storing a Registration” (p. 47)
13.
Memory Bank Select [M–] Piston/[M+] Piston
Use these pistons to switch memory banks when you want to use
more than six combinations of sounds.
➔
“Recalling a Registration from a Different Memory Bank” (p. 49)
14.
[NEXT] Piston
Pressed to call up the settings stored at the next general memory
piston, in numerical order, like this: 1 → 2 → 3.
➔
“Recalling Registrations Successively” (p. 49)
15.
Bass Coupler [BASS] Piston
This causes the lowest note played on the lower manual to be
sounded by the PEDAL division sound.
➔
“Using the Bass Coupler” (p. 33)
[STOP] Piston
17.
This stops playback or recording of a song.
18.
[PLAY/PAUSE] Piston
This starts or pauses playback of a song.
➔
“Practicing Along with a Preset Song or Performance Data”
(p. 50)
[REC] Piston
19.
Use this when you want to record your playing.
➔
“Recording Your Performances” (p. 56)
General Cancel [0] Piston
20.
This sets the organ to the condition in which all tablets and couplers
are cancelled, so that no sounds are selected.
It’s convenient to use this piston when you want to specify a
combination of sounds from scratch.
➔
“Resetting the Sound Settings (General Cancel)” (p. 47)
17
Names of Things and What They Do
1 32 4
Display and Panel
1
32
4 5
1.
Display
Various information is shown here.
[Select/Menu] Knob/[Satellite Volume] Knob
2.
Turn: Adjusts the volume of the satellite speakers.
When you’re in a menu screen for making detailed
settings, turn this knob to select the item you want to
operate.
Press: Takes you to a menu screen, or finalizes a setting item.
External Connectors
1.
OUTPUT L/MONO, R (Output) Jacks
You can connect an external speaker system here so that the sound
of the organ is played from the connected speakers (p. 74).
INPUT L/MONO, R (Input) Jacks
2.
You can connect an external sound module or similar device here so
that its sounds are heard from the organ’s speakers (p. 75).
MIDI OUT/IN Connectors
3.
You can connect external MIDI devices here to exchange
performance data with the organ (p. 76).
4.
Connector for Service Use
This connector is for technical service use only. Do not connect
anything to this connector.
3.
[Value/Exit Menu] Knob
Turn: Adjusts a setting.
Press: Returns you to the previous menu, or cancels an
operation.
[Master Volume] Knob
4.
This adjusts the volume of the entire organ.
[Reverb] Knob
5.
This adjusts the depth of reverberation.
18
Before You Start Playing
Connecting the Pedalboard
* The illustration shows the C-330, but the connections are the same
for the C-380 as well.
1.
Adjusting the pedalboard adjuster.
Turn the pedalboard adjuster (four locations) to lower it until the
pedalboard does not wobble.
* If there is a gap between the pedalboard and the floor, the
pedalboard may be damaged.
* In particular when placing the instrument on carpet, adjust this so
that the pedalboard firmly contacts the floor.
Adjuster
Please don’t get your
fingers pinched.
2.
Connect the cable extending from the bottom of the
main unit to the PEDAL OUT jack of the pedalboard.
Using the Music rest
Gently raise the music rest, then secure it in place as
1.
shown in the figure.
Metal Fittings
To collapse the music rest, fold in the metal fittings while
2.
supporting the music rest with both hands and gently
fold down the music rest.
Do not pull down the music stand.
Placing the Bench
* The illustration shows the C-330, but the connections are the same
for the C-380 as well.
1.
Place the organ bench over the pedalboard.
As shown in the illustration, position the bench so that the side with
the footrest faces the organ, taking care that the footrest does not
touch the pedalboard.
Turn the bench adjusters (four locations) to lower them, adjusting
the height so that the bench does not wobble.
3.
Place the pedalboard.
Place the pedalboard so that it contacts the organ.
Please don’t get your
fingers pinched.
Do not adjust the adjusters more than 25 mm (1 inch) from the
floor.
Please don’t get your
fingers pinched.
less than
25 mm
(1 inch)
Adjuster
19
Before You Start Playing
Corners cut off
Satellite Speaker Grill
Installing the Satellite Speakers
If the satellite speakers are installed in any way other than that
described below, they may fall down, causing injury.
Attaching to the Main Unit (C-330 Only)
When the C-330 is shipped from the factory, the satellite speakers
are wrapped in packing material and stored inside the organ. Please
remove this packing material before use.
4.
Connect the speaker cables of the satellite speakers to
the main unit.
When the C-330 is shipped from the factory, the satellite
speaker cables are connected to the organ.
5.
Attach the satellite speaker grill.
Position the satellite speaker grill so that the cut-off corners are
upward.
Lightly tap the outer edge of the grill until it snaps firmly into place.
If attaching the satellite speakers to the main unit, leave at
least 10 cm between the back of the organ and the wall to
ensure optimal results.
Insert your fingers into the openings where the corners
1.
of the satellite speaker grill have been cut off, and
remove the grill.
The satellite speaker grill is attached with hook-and-loop
fasteners.
2.
Take the satellite speakers out of the main unit, and
remove the packing material.
Tilt the satellite speakers when removing or inserting them.
Attaching to the Wall
You can obtain a more spacious sound by attaching the satellite
speakers to the wall.
* The satellite speakers should not be installed in a manner that
differs from the instructions below. Failure to comply could result in
bodily injury.
* Keep the included screws in a safe place out of children’s reach, so
there is no chance of them being swallowed accidentally. Do not
use any screws other than the included screws.
* Do not use any screws other than the included screws.
* Attach the speakers to a wooden wall at least 9 mm (3/8 inches)
thick. Do not attach the speakers to any other type of wall.
* Replacement screws should only be obtained from the nearest
Roland Service Center, or an authorized Roland distributor, as listed
on the “Information” page.
Satellite speaker attachment locations
Attach the left and right satellite speakers at the same height,
centered on the organ.
We recommend that you attach the speakers 1.8 meters (6 feet) or
higher above the floor.
Satellite Speaker
3.
Position the satellite speakers so their cloth-covered side
faces the rear of the organ.
20
1.8 meters
(6 feet)
or higher
1.8 meters
(6 feet)
or higher
Before You Start Playing
Right Speaker
Left Speaker
Attaching the satellite speakers
1.
Use a Phillips screwdriver to attach the included screws
to the wooden wall.
Wooden wall at least 9 mm
(3/8 inches)
2.
Insert the head of the included screw into the wall
hanging hook located on the rear of the satellite speaker.
Wall Hanging Hook
22.5 mm
(15/16 inches)
For the C-330
1.
Remove the satellite speaker grill.
Corners cut off
Connect the speaker cable connectors to the satellite
2.
speaker jacks located on the back of the organ.
Satellite Speaker Grill
The satellite speakers can be attached in either the vertical or
horizontal orientation.
Connecting the Satellite Speakers to the Organ
Connect the speaker cables of the satellite speakers to the organ.
Make sure that the organ’s power is turned off before you
connect the satellite speakers to the organ.
For the C-380
1.
Connect the speaker cable connectors to the satellite
speaker jacks located on the back of the organ.
3.
Attach the satellite speaker grill.
Pass the speaker cables through the openings where the corners of
the satellite speaker grill have been cut off.
Position the satellite speaker grill so that the side with the corners
cut off is at the top. Lightly tap the outer edge of the grill until it
snaps firmly into place.
Right Speaker
Left Speaker
21
Before You Start Playing
Open
Lock
Opening and Closing the Keyboard
Cover (C-380 only)
* When opening or closing the cover, take care not to pinch your
fingers. When small children use the organ, they should be assisted
by an adult.
* For safety, close the cover before moving the organ.
Connecting the Power Cord
* Only use the power cord supplied with this instrument.
* Whenever you do not intend to use the instrument for extended
periods of time, pull out the power cord from the AC outlet.
For the C-380
1.
First, make sure that the [POWER] switch is OFF.
The bottom side is pressed OFF
Connect the supplied power cord to the AC Inlet
2.
connector, then plug the other end into an AC outlet.
1.
To open the cover, use both hands to slide it upward.
Slide the cover until it is completely stowed inside the organ.
2.
To close the cover, use both hands to slide it toward
yourself.
Locking the Cover
The C-380’s keyboard cover has a lock.
Keep the included key out of the reach of children so that it will
not be swallowed accidentally.
Open
Lock
22
For the C-330
1.
First, make sure that the [POWER] switch is OFF.
Upper position OFF
2.
Connect the supplied power cord to the AC Inlet
connector, then plug the other end into an AC outlet.
Before You Start Playing
23
Before You Start Playing
Increase the VolumeDecrease the Volume
Turning the Power On and Off
Once the connections have been completed (p. 22), turn on
power to your various devices in the order specified. By turning
on devices in the wrong order, you risk causing malfunction
and/or damage to speakers and other devices.
Turning On the Power
Make sure of the following before the power is turned
1.
on.
• Is the power cord correctly connected to the AC inlet?
• Is the power cord correctly connected to the AC outlet?
Turn the [Master Volume] knob all the way to the left to
2.
minimize the volume.
For the C-330
Lower position ON
The main screen will appear in the display.
3.
Press the [POWER] switch to turn on the power.
* Always make sure to have the volume level turned down before
switching on power. Even with the volume all the way down, you
may still hear some sound when the power is switched on, but this is
normal, and does not indicate a malfunction.
For the C-380
The top side is pressed ON
This unit is equipped with a protection circuit. A brief interval
(a few seconds) after power up is required before the unit will
operate normally.
4.
Select a stop.
For details, refer to “Playing Various Sounds” (p. 29).
Even though the power has been turned on, playing the
keyboard will not produce sound until you’ve selected a sound
(stop).
5.
Adjust the volume to an appropriate level by moving the
[Master Volume] knob.
Adjust the volume while you play the keyboard to produce sound.
Turning the knob toward the right will increase the volume, and
turning it toward the left will decrease the volume.
24
Depress the expression pedal to the maximum volume.
Before You Start Playing
Upper position OFF
Turning Off the Power
1.
Turn the [Master Volume] knob all the way to the left to
minimize the volume.
2.
Press the [POWER] switch to turn off the power.
* You may still hear some sound when the power is switched off, but
this is normal, and does not indicate a malfunction.
* If you need to turn off the power completely, first turn off the
POWER switch, then unplug the power cord from the power outlet.
Refer to “Power Supply” (p. 6).
For the C-380
The bottom side is pressed OFF
For the C-330
Connecting Headphones
* To prevent possible auditory damage, loss of hearing, or damage to
the headphones, the headphones should not be used at an
excessively high volume. Use the headphones at a moderate
volume level.
* Once a plug for a set of headphones is plugged into the Phones jack,
no sound will be heard from the organ’s speakers.
* To prevent damage to the cord, handle the headphones only by the
headset or the plug.
* Use stereo headphones.
* Roland organs feature Phones jacks. These allow you to play without
having to worry about bothering others around you, even at night.
However, you should be careful that you don’t disturb your
neighbors, since floors and walls can too easily transmit vibrations
(especially vibrations from the pedalboard). You should be
especially careful at night or when you’re using headphones.
1.
Turn the [Master Volume] knob all the way to the left to
minimize the volume.
2.
Connect your headphones to the [Phones] jack.
The sound from the built-in speakers stops.
Now, sound is heard only through the headphones.
For the C-380
For the C-330
3.
Adjust the headphones volume with the [Master Volume]
knob.
25
Before You Start Playing
Connecting the USB memory
Songs you record on the organ and Registration sets you create can
be copied to separately available USB memory for safekeeping.
You can also play back performance data that’s been stored on USB
memory.
* Use USB memory available from Roland. We cannot guarantee
correct operation if other brands of USB memory are used. Note that
only USB memory keys can be used—never use any other kind of
USB device.
* Carefully insert the USB memory all the way in—until it is firmly in
place.
* If you’re using new USB memory, you’ll need to initialize (format) it
on the this unit. For details, refer to “Formatting USB Memory” (p.
62).
Note on using USB memory
For the C-380
The USB connector located at the bottom center of the organ is a
servicing connector for purposes such as maintenance. Do not
connect anything to this servicing connector (USB FOR UPDATE). Do
not touch or insert anything into the small holes marked A and B
located at the left of the servicing connector.
The USB connector holder of the C-380 will rotate 90 degrees to left
or right. By turning the USB connector holder to the left or right, you
can avoid accidents, such as the damage that might be caused by
accidentally striking a connected USB memory.
* Be sure to grasp the holder itself when rotating it. Do not rotate the
holder by grasping the connected USB memory.
* Be careful not to pinch your fingers when rotating the holder.
For the C-330
26
Before You Start Playing
About the Display
Contents of the Main Screen
Immediately after you turn on the power, the following “main
screen” will appear.
1.
General memory bank number (p. 48)
This shows the currently used general memory bank.
General memory piston number
2.
This shows the currently used general memory piston.
3.
Keyboard transposition status (p. 41)
Range (half a semitone)
-6– +5
Return to the Main Screen
In order to perform an operation such as changing the organ’s
settings, you’ll need to start by returning to the main screen.
Press the [Value/Exit Menu] knob a number of times.
1.
Adjusting the Display Contrast
From the main screen, press the [Select/Menu] knob.
1.
Turn the [Select/Menu] knob to select “6 Console.”
2.
4.
Temperament (p. 38)
Available Settings
EQUAL, WERCK., KIRN.1, KIRN.3, VALLO., MEAN.D, MEAN.E, PYTHG., M.BACH
Reference pitch (master tuning: p. 39)
5.
Available Settings (Hz)
392: VERSAILLES
415: BAROQUE
440: MODERN (standard)
465: VENETIAN
You can also adjust this tuning within the range of the
reference pitch.
6.
Expression pedal status (p. 42)
This indicates the keyboard(s) that are affected by the expression
pedal.
Indication
I PII
IP
II The expression pedal affects the MAN II division
Off The expression pedal will not affect any division
Explanation
The expression pedal affects all divisions (MAN I, MAN II,
and PEDAL division)
The expression pedal affects the MAN I division and the
PEDAL division
3.
Press the [Select/Menu] knob to access the “Console”
screen.
4.
Turn the [Select/Menu] knob to select “Display Contrast.”
5.
Turn the [Value/Exit Menu] knob to adjust the
brightness.
Range
0–30
6.
Press the [Value/Exit Menu] knob twice to return to the
main screen.
This setting will return to the default value when you turn off
the power, but you can store the setting so that it will be
remembered even after the power is turned off. For details,
refer to “Storing Your Settings (Customize)” (p. 73).
7.
Volume of the expression pedal (p. 42)
27
Before You Start Playing
Listening to the Demo Songs
This Roland organ has several built-in demo songs.
For more information of the built-in demo songs, refer to “List of
Preset Song/Demo Song” (p. 78).
From the main screen, press the [Select/Menu] knob.
1.
Turn the [Select/Menu] knob to select “1 Demo.”
2.
Press the [Select/Menu] knob to access the “Demo”
3.
screen.
You can also access the Demo screen from the main screen by
holding in the [SET] piston and pressing the [PLAY/PAUSE]
piston.
Select a demo song.
4.
* All rights reserved. Unauthorized use of this material for purposes
other than private, personal enjoyment is a violation of applicable
laws.
* No data for the music that is played will be output from MIDI OUT
jack.
* If you play back in the “Song Recorder” screen, you’ll be able to
individually mute the performance of each division (p. 50).
If a screen like the following appears
If internal memory contains performance data that has not been
saved, the following message will appear when you attempt to
listen to a demo song.
• If you want to discard the performance data without saving it, press
the [SET] piston.
• If you don’t want to erase the performance data, press the [Value/
Exit Menu] knob. Save the performance data as described in “Saving
a Recorded Song” (p. 57).
1. Turn the [Select/Menu] knob to select the demo song “Group.”
2. Turn the [Value/Exit Menu] knob to change the demo song
group.
3. Turn the [Select/Menu] knob to select “Song.”
4. Turn the [Value/Exit Menu] knob to change the song.
Press the [PLAY/PAUSE] piston, and the demo song will
5.
start playing.
When the selected demo song ends, playback will continue with the
next demo song.
6.
Press the [STOP] piston to stop the demo song.
To adjust the satellite speaker volume during the demo song
playback, turn the [Select/Menu] knob to select “Satellite VR”,
and turn the [Value/Exit Menu] knob.
7.
Press the [Value/Exit Menu] knob twice to exit the demo
screen.
28
Performing
Playing Various Sounds
Selecting Stops (sounds)
By pressing the sound tablets you can play a variety of pipe organ sounds. The sounds assigned to the tablets are called “stops.”
The sound tablets are organized into groups called “divisions.” These tablets are called “division tablets.”
If the indicator of a division tablet is lit, you’ll be able to play the corresponding stop.
fig.stop-up.eps
Press the lower part of the tablet to
select the stop; the indicator is lit
Press the upper part of the tablet to
turn off the stop; the indicator is unlit
fig.LCD016.eps
fig.variation01.eps
1.
Press the lower part of one of the “PEDAL,” “MAN I,” or “MAN II” division tablets.
The indicator will light, and the stop will be selected.
The display will show the “Voice Palette” screen (p. 30), indicating the sound of the stop you selected.
The main screen will automatically reappear after a while.
* Immediately after the power is turned on, no stops are selected, meaning that the keyboard will not produce sound.
You can also access the “Voice Palette” screen by holding in the [SET] piston and pressing the desired division tablet.
The stop will blink for a moment if a stop variation (p. 30) is selected.
Indicator will light when you
press the lower part of the tablet
Cancel the selected Stop
1.
Press the upper part of the tablet.
The tablet’s indicator will turn off and the selected sound will be cancelled.
Blinks
momentarily
Lit again
29
Loading...