Roland AT-75, 5100001499-01, 5100001499 User Manual

201b

202

Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY” (p. 3), and “IMPORTANT NOTES” (p. 6). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.

form without the written permission of ROLAND CORPORATION.

WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

WARNING - When using electric products, basic precautions should always be followed, including the following:

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

For the U.K.

IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.

BLUE: BROWN:

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Under no circumstances must either of the above wires be connected to the earth terminal of a three pin plug.

NEUTRAL LIVE

USING THE UNIT SAFELY

Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly.

Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly.

* Material damage refers to damage or

other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets.

Do not disassemble or modify

002a

Do not disassemble or modify this device.

......................................................................................

Do not repair or replace parts

003

Never attempt to repair this device or replace parts. If repair or part replacement should become necessary, you must contact your dealer or a Roland service center.

......................................................................................

Do not use or store in the following types of locations

004

• Subject to temperature extremes (e.g., direct sunlight in an enclosed vehicle, near a heating duct, on top of heat-generating equipment); or are

• Damp (e.g., baths, washrooms, on wet floors); or are

• Exposed to steam or smoke; or are

• Subject to salt exposure; or are

• Humid; or are

• Exposed to rain; or are

• Dusty or sandy; or are

• Subject to high levels of vibration and shakiness.

......................................................................................

Do not place in an unstable location

007

Do not place this device on an unstable stand or a tilted surface. You must place it in a stable and level location.

......................................................................................

Connect the power cord to an outlet of the correct voltage

008a

You must connect the power cord to an AC outlet of the correct voltage as marked on the device.

......................................................................................

The symbol alerts the user to important instructions or warnings.The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger.

The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled.

The symbol alerts the user to things that must be carried out. The specific thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the powercord plug must be unplugged from the outlet.

Use only the included power cord

008e

You must use only the power cord included with the device. Do not use the included power cord with any other device.

......................................................................................

Do not bend the power cord or place heavy objects on it

009

Do not bend the power cord excessively, or place heavy objects on the power cord. Doing so will damage the power cord, and may cause short circuits or faulty connections, possibly resulting in fire or electrical shock.

......................................................................................

Do not share an outlet with an unreasonable number of other devices

015

Do not connect excessive numbers of electrical devices to a single power outlet. In particular, when using a power strip, exceeding the rated capacity (watts/amps) of the power strip may cause heat to be generated, possibly melting the cable.

......................................................................................

Avoid extended use at high volume

010

This device, either by itself or used in conjunction with headphones, amps, and/or speakers, is capable of producing volume levels that can cause permanent hearing damage. If you experience impaired hearing or ringing in your ears, immediately stop using the device and consult a medical specialist.

......................................................................................

Do not insert foreign objects

011

Never allow foreign objects (flammable objects, coins, wires, etc.) to enter this device. This can cause short circuits or other malfunctions.

......................................................................................

USING THE UNIT SAFELY

Turn off the power if an abnormality or malfunction occurs

012a

If any of the following should occur, immediately turn off the power, disconnect the power cord from the AC outlet, and contact your dealer or a service center to have the device serviced.

• The power cord is damaged

• The device produces smoke or an unusual smell

• A foreign object enters the device, or liquid spills into the device

• The device becomes wet (by rain, etc.)

• An abnormality or malfunction occurs in the device

......................................................................................

Do not allow children to use without supervision

013

In households with children, take particular care against tampering. If children are to use this device, they must be supervised or guided by an adult.

......................................................................................

Do not drop or subject to strong impact

014

Do not drop this device or subject it to strong impact.

......................................................................................

Do not use overseas

016

If you wish to use this device overseas, please contact your dealer or a service center.

......................................................................................

Do not use a CD-ROM in an audio CD player or DVD player

023

If you attempt to play back a CD-ROM in a conventional audio CD player or DVD player, the resulting high volume may damage your hearing or your speakers.

......................................................................................

Do not place containers of water on the device

026

Do not place containers of water (such as a flower vase) or drinks on the device. Nor should you place containers of insecticide, perfume, alcoholic liquids, nail polish, or spray cans on the device. Liquids that spill into the device may cause it to malfunction, and may cause short circuits or faulty operation.

......................................................................................

Place in a well ventilated location

101a

When using this device, ensure that it is placed in a well ventilated location.

..........................................................................................................

Grasp the plug when connecting or disconnecting the power cord

102b

When connecting or disconnecting the power cord to/from an AC outlet or the device itself, you must grasp the plug, not the cord.

..........................................................................................................

Periodically wipe the dust off the power cord plug

103a

From time to time, you should unplug the power cord from the AC outlet and use a dry cloth to wipe the dust off of it. You should also unplug the power cord from the AC outlet if you will not be using the device for an extended period of time. Dust or dirt that accumulates between the power cord plug and the AC outlet can cause a short circuit, possibly resulting in fire.

..........................................................................................................

Manage cables for safety

104

Ensure that the connected cables are organized and managed in a safe manner. In particular, place the cables out of reach of children.

..........................................................................................................

Do not stand or place heavy objects on this device

106

Do not stand on this device, or place heavy objects on it.

..........................................................................................................

Do not connect or disconnect the power cord with wet hands

107b

Do not connect or disconnect the power cord to the device or AC outlet while holding the power cord plug with wet hands.

..........................................................................................................

Cautions when moving this device

108d

If you need to move the instrument, take note of the precautions listed below.

• Check whether the knob bolts fastening the device to its stand have become loose. If they are loose, tighten them firmly.

• Disconnect the power cord.

• Disconnect external devices.

• Remove the music stand.

Since this product is very heavy, you must make sure that a sufficient number of people are on hand to help, so you can lift and move it safely, without causing strain. It should be handled carefully, all the while keeping it level. Make sure to have a firm grip, to protect yourself from injury and the instrument from damage.

..........................................................................................................

Unplug the power cord from the AC outlet before cleaning

109a

Before you clean the device, turn off the power and unplug the power cord from the AC outlet.

..........................................................................................................

If there is a possibility of lightning strike, disconnect the power cord from the AC outlet

110a

If there is a possibility of lightning strike, immediately turn off the power and disconnect the power cord from the AC outlet.

..........................................................................................................

Cautions when using the seat

117: Selection

You must observe the following cautions when using the seat.

• Do not play with the seat or use it as a stepstool.

• Do not allow two or more people to sit on the seat simultaneously.

• Do not sit on the seat if the bolts fastening the legs are loose. (If they are loose, use the included tool to retighten them.)

..........................................................................................................

Keep small items out of the reach of children

118b

To prevent small items such as the following from being swallowed accidentally, keep them out of the reach of children.

• Included items

• Cord hook

• Wing nut for cord hook

• Screws for assembling the stand

• Knob bolts

• Cord clamps

..........................................................................................................

Do not remove the speaker grille and speaker

121

Do not remove the speaker grille and speaker by any means. Speaker not user replaceable. Shock hazardous voltages and currents are present inside the enclosure.

..........................................................................................................

USING THE UNIT SAFELY

IMPORTANT NOTES

Power Supply

301

• Do not connect this device to the same electrical outlet as an inverter-controlled device such as a refrigerator, microwave oven, or air conditioner, or a device that contains an electric motor. Depending on how the other device is used, power supply noise could cause this device to malfunction or produce noise. If it is not practical to use a separate electrical outlet, please connect this device via a power supply noise filter.

307

• Before you make connections, you must switch off the power on all devices to prevent malfunction and/or speaker damage.

308

• Although the LCD and LEDs are switched off when the Power switch is switched off, this does not mean that the unit has been completely disconnected from the source of power. If you need to turn off the power completely, first turn off the Power switch, then unplug the power cord from the power outlet. For this reason, the outlet into which you choose to connect the power cord’s plug should be one that is within easy reach and readily accessible.

Location

351

• If this device is placed near devices that contain large transformers, such as power amps, hum may be induced in this device. If this occurs, move this device farther away or change its orientation.

352a

• If this device is operated near a television or radio, color distortion may be seen in the television screen or noise may be heard from the radio. If this occurs, move this device farther away.

352b

• Keep your cell phone powered off or at a sufficient distance from this device. If a cell phone is nearby, noise may be heard when a call is received or initiated, or during conversation.

354b

• Do not leave this device in direct sunlight, near devices that produce heat, or in a closed-up automobile. Do not allow illumination devices operated in close proximity (such as a piano light) or powerful spotlights to shine on the same location on this device for an extended time. This can cause deformation or color change.

355b

• If you move this device between locations of radically different temperature or humidity, water droplets (condensation) may form inside the device. Using the device in this condition will cause malfunctions, so please allow several hours for the condensation to disappear before you use the device.

356

• Do not allow items made of rubber or vinyl to remain on top of this device for an extended time. This can cause deformation or color change.

358

• Do not leave objects on top of the keyboard or pedalboard. This can cause malfunctions such as failure to sound.

359

• Do not affix adhesive labels to this device. The exterior finish may be damaged when you remove the labels.

360

• Depending on the material and temperature of the surface on which you place the unit, its rubber feet may discolor or mar the surface.You can place a piece of felt or cloth under the rubber feet to prevent this from happening. If you do so, please make sure that the unit will not slip or move accidentally.

Care

401b

• For everyday care, wipe with a soft dry cloth, or remove stubborn dirt using a tightly wrung-out cloth. If this device contains wooden components, wipe the entire area following the direction of the grain. The finish may be damaged if you continue strongly rubbing a single location.

Addition

• If water droplets should adhere to this device, immediately wipe them off using a soft dry cloth.

402

• Do not use solvents such as benzene, thinner, or alcohol, since these can cause deformation or color change.

Servicing

452

• If you return this device for servicing, the contents of memory may be lost. Please store important contents on USB memory, or make a note of the contents. We take utmost care to preserve the contents of memory when performing service, but there may be cases when the stored content cannot be recovered because the memory section has malfunctioned. Please be aware that we cannot accept responsibility for the recovery of lost memory content or for any consequences of such loss.

Other Cautions

551

• Stored content may be lost due to a malfunction of the device or because of inadvertent operation. You should back up important content on USB memory as a safeguard against such loss.

552

• We cannot accept responsibility for the recovery of any content lost from internal memory or USB memory, or for the consequences of such loss.

553

• Do not apply excessive force to the buttons, knobs, or input/ output jacks, since this may cause malfunctions.

554

• Never strike or apply strong pressure to the display.

556

• When connecting or disconnecting cables, grasp the plug (not the cable) to prevent short circuits or broken connections.

557

• This device may produce a certain amount of heat, but this is not a malfunction.

558a

• Please enjoy your music in ways that do not inconvenience other people nearby, and pay particular attention to the volume at nighttime. Using headphones will allow you to enjoy music without having to be concerned about others.

559b

• When transporting or shipping this device, package it in an appropriate amount of cushioning material. Scratches, damage, or malfunctions may occur if you transport it without appropriate packaging.

560

• If using the music rest, do not apply excessive force to it.

562

• Some connection cables contain a resistor. Do not connect such cables to this device. Doing so may make the volume extremely low or inaudible. Please use connection cables not containing a resistor.

IMPORTANT NOTES

Floppy Disk Handling

(Using Optional Floppy Disk Drive)

651

• Floppy disks contain a plastic disk with a thin coating of magnetic storage medium. Microscopic precision is required to enable storage of large amounts of data on such a small surface area. To preserve their integrity, please observe the following when handling floppy disks:

• Never touch the magnetic medium inside the disk.

• Do not use or store floppy disks in dirty or dusty areas.

• Do not subject floppy disks to temperature extremes

(e.g., direct sunlight in an enclosed vehicle). Recommended temperature range: 10–50 degrees C (50–122 degrees F).

• Do not expose floppy disks to strong magnetic fields,

such as those generated by loudspeakers.

652

• Floppy disks have a “write protect” tab which can protect the disk from accidental erasure. It is recommended that the tab be kept in the PROTECT position, and moved to the WRITE position only when you wish to write new data onto the disk.

fig.DiskProtect.e.eps

Rear side of the disk

Write

(can write new data onto disk)

Write Protect Tab

653

• The identification label should be firmly affixed to the disk.

Protect

(prevents writing to disk)

Should the label come loose while the disk is in the drive, it may be difficult to remove the disk.

654

• Store all disks in a safe place to avoid damaging them, and to protect them from dust, dirt, and other hazards. By using a dirty or dust-ridden disk, you risk damaging the disk, as well as causing the disk drive to malfunction.

USB Memory Handling

(Using Optional USB Memory)

704

• When connecting USB memory, firmly insert it all the way in.

705

• Do not touch the pins of the USB memory connector, or allow them to become dirty.

708

• USB memory is made using high-precision electronic components, so please observe the following points when handling it.

• To prevent damage from static electrical charges,

discharge any static electricity that might be present in your body before handling USB memory.

• Do not touch the terminals with your fingers or any metal

object.

• Do not bend or drop USB memory, or subject it to strong

impact.

• Do not leave USB memory in direct sunlight or in

locations such as a closed-up automobile.

• Do not allow USB memory to become wet.

• Do not disassemble or modify USB memory.

Addition

• When connecting USB memory, position it horizontally with the External Memory connector and insert it without using excessive force. The External Memory connector may be damaged if you use excessive force when inserting USB memory.

Addition

• Do not insert anything other than USB memory (e.g., wire, coins, other types of device) into the External Memory connector. Doing so will damage the External Memory connector.

Addition

• Do not apply excessive force to the connected USB memory.

Addition

• If you will not be using USB memory for an extended period of time, close the USB memory cover.

988

• Security Slot ( ) (P.19) http://www.kensington.com/

Handling the CDs (CD-ROMs)

(Using Optional CD Drive)

Add

• When handling the discs, please observe the following.

• Do not touch the encoded surface of the disc.

• Do not use in dusty areas.

• Do not leave the disc in direct sunlight or an enclosed

vehicle.

801

• Avoid touching or scratching the shiny underside (encoded surface) of the disc. Damaged or dirty CD-ROM discs may not be read properly. Keep your discs clean using a commercially available CD cleaner.

Add

• Keep the disc in the case.

Add

• Do not keep the disc in the CD drive for a long time.

Add

• Do not put a sticker on the label of the disc.

Add

• Wipe the disc with a soft and dry cloth radially from inside to outside. Do not wipe along circumference.

Add

• Do not use benzine, record cleaner spray or solvents of any kind.

Add

• Do not bend the disc. Bending discs may prevent proper reading and writing of data, and may further result in malfunction.

852

• This product can be used to record or duplicate audio or visual material without being limited by certain technological copy-protection measures. This is due to the fact that this product is intended to be used for the purpose of producing original music or video material, and is therefore designed so that material that does not infringe copyrights belonging to others (for example, your own original works) can be recorded or duplicated freely.

853

• Do not use this unit for purposes that could infringe on a copyright held by a third party. We assume no responsibility whatsoever with regard to any infringements of third-party copyrights arising through your use of this unit.

203

* GS ( ) is a registered trademark of Roland

Corporation.

Add

* XGlite ( ) is a registered trademark of Yamaha

Corporation.

220

* All product names mentioned in this document are

trademarks or registered trademarks of their respective owners.

Main Features

We want to take a moment to thank you for your purchase of the Roland Organ “Music ATELIER AT-75.” The ATELIER is an electronic organ which provides a generous collection of rich organ sounds. In addition, it is designed to be easy to learn and use. In order to enjoy reliable performance of your new keyboard for many years to come, please take the time to read through this manual in its entirety.

Basic Concepts of the ATELIER Series

A full complement of organ sounds

A wide range of basic organ sounds, ranging from jazz organ and pipe organ to theatre organ, are onboard so you are sure to enjoy having access to all the sounds you expect from an organ.

Panel layout based on a tradition of emphasis on realtime operation

Based on the idea that you should be able to sit down and begin playing immediately, the operation buttons of the panel are arranged by function as dictated by classic organ traditions, ensuring easy and intuitive operation. All models of the ATELIER series feature the same operability, allowing you to start playing immediately even if you switch models.

High-quality sounds that you can use without editing

In addition to a full range of organ sounds, high-quality sounds such as strings and brass are also included onboard. You can simply select sounds and enjoy playing the organ—no need to perform complicated editing operations.

Design utilizes your existing music data

The ATELIER series is designed so that even on new models, you will feel right at home and can begin playing immediately. Consideration has been given to data compatibility, and existing song data or Registration data can be moved to USB memory or used by connecting a floppy disk drive.

Music styles from around the world

A rich variety of the world’s most representative music styles (Rhythm and Auto Accompaniment patterns) are built-in, allowing you to more readily perform music from almost any genre.

Utilizes SMF music files

Compatible with General MIDI 2, the world standard in SMF music files. Since an External Memory connector is provided, you can connect separately available USB memory or a floppy disk drive and take advantage of the wide range of commercially available SMF music files. You can also mute parts, allowing you to practice the part for each hand separately, and enjoy performing ensemble with the music files.

Features

Harmonic bars for creating organ sounds

The organ is equipped with “Harmonic bars,” which are much like the controllers used on traditional jazz organs. By operating the harmonic bars, you can easily create a diverse variety of organ sounds.

USB Memory

You can connect separately sold USB memory or a floppy disk drive, and play back SMF music files. Performances you record or Registration data you create can also be saved on USB memory or a floppy disk, or you

can save SMF music files or Registrations from USB memory or a floppy disk into internal User Memory.

Main Features

Highly realistic Rhythms and Automatic Accompaniment functions

All Rhythms use data from performances by professional drummers, featuring high-quality patterns with all the grooves and subtle nuance of the real thing. In addition, you can use Automatic Accompaniments that are perfectly matched to each Rhythm to enjoy the feeling of playing with your own band in the background.

Human voices

In addition to a full complement of organ tones, the ATELIER also features tones that express a wide range of human vocal qualities, including “Jazz Scat,” which changes according to how firmly the keys are pressed, and “Classical” tones that perfectly express that choir image.

Active Expression Sounds

For some of the sounds, moving the expression pedal will vary not only the volume but also the tone, or add other sounds. From pianissimo to fortissimo, the tonal character of the sound itself will change as you perform a crescendo, or strings may appear behind the piano, creating dynamic changes in tonality.

Harmony Intelligence

The Harmony Intelligence function automatically adds harmony to the upper keyboard sound according to the chord you play in the lower keyboard. This gives you greater tonal depth and a more powerful performance.

Split Function

The 49-key lower manual can be split into separate sections, with each being used to play a different tone.

Conventions Used in This Manual

This manual uses the following conventions in the interest of simpler, more concise instructions.

• The AT-75 are abbreviated in this manual as “ATELIER” respectively.

985

• The explanations in this manual include illustrations that depict what should typically be shown by the display. Note, however, that your ATELIER may incorporate a newer, enhanced version of the system (e.g., includes newer sounds), so what you actually see in the display may not always match what appears in the manual.

• Button names are enclosed in square brackets (“[ ]”), as in [Drums/SFX] button.

•[▲] [▼], [ ] [ ] means that you should press one or the other button. Example: Reverb [▲] [▼] buttons, Tempo [ ] [ ] buttons.

• An asterisk (*) or a at the beginning of a paragraph indicates a note or precaution. These should not be ignored.

• (p. **) refers to pages within the manual.

• The diagram of the ATELIER at the top of the page shows the location of the buttons to be pressed, etc.

NOTE

USING THE UNIT SAFELY........................................................................ 3

IMPORTANT NOTES............................................................................... 6

Main Features........................................................................................ 8

Conventions Used in This Manual............................................................................... 9

Contents.............................................................................................. 10

Panel Descriptions................................................................................ 14

Before You Start Playing ...................................................................... 16

Setting Up the Music Rest.................................................................................................. 16

Connecting the Power Cord .............................................................................................. 16

Turning the Power On and Off ..........................................................................................16

Turning On the Power ............................................................................................. 16

Turning Off the Power ............................................................................................. 17

Using Headphones ..........................................................................................................17

Using the Cord Hook .......................................................................................................18

Restoring All the Factory Default Settings (Factory Reset) ....................................................... 18

Adjusting the Contrast of the Screen...................................................................................18

Using the External Memory ............................................................................................... 19

Connecting the USB Memory ...................................................................................19

Connecting the Floppy Disk Drive (Sold Separately).................................................... 19

Using a CD..................................................................................................................... 20

Connecting a CD Drive (Sold Separately) .................................................................. 20

About the Adjuster ........................................................................................................... 20

About the Display ................................................................................ 21

Basic Screens.........................................................................................................21

Selecting and Playing Sounds............................................................... 22

Listening to the Demo Songs.............................................................................................. 22

Selecting Voices ..............................................................................................................24

About the Voices and Parts ......................................................................................24

Functions of the Upper/Lower/Pedal Bass Sound Select Buttons ...................................25

Selecting the Upper/Lower/Pedal Bass Voices ...........................................................25

Selecting Solo Voice ............................................................................................... 26

Selecting a Voice Using the [Others] Button ...............................................................27

Creating Organ Sounds (Vintage Organ) ...........................................................................28

Playing a Vintage Organ Voice................................................................................ 30

Performing with an Active Expression Voice ........................................................................ 33

Adjust the Volume Balance................................................................................................ 34

Transpose the Pitch in Octave Units (Octave Shift)................................................................ 35

Sustaining Notes Played on the Lower Keyboard ................................................................. 36

Playing Drums from the Entire Lower Keyboard (Drums/SFX) .................................................36

Changing the Drums/SFX Set...................................................................................37

Using the Lower Keyboard to Play the Bass Voice (Bass Split)................................................ 38

Changing the Bass Split Point................................................................................... 39

Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] button) ............................ 40

Contents

Using the Rhythm Performance............................................................. 41

Selecting a Rhythm........................................................................................................... 41

Using Rhythms Stored in User Memory ...................................................................... 42

Playing Rhythm................................................................................................................ 43

Starting at the Press of a Button ................................................................................ 43

Starting the Rhythm Automatically When You Play the Lower Keyboard or Pedalboard

(Sync Start) ............................................................................................................ 44

Stopping the Rhythm ............................................................................................... 45

Changing a Tempo of Rhythm and Automatic Accompaniment.............................................. 46

Playing a Countdown Sound When the Intro Ends ...............................................................46

Playing Rhythm and Automatic Accompaniment................................................................... 47

Adding Variety to the Rhythm or Automatic Accompaniment .................................................48

Changing the Arrangement of the Rhythm and Accompaniment (Variation)....................48

Turning Chord Intelligence On/Off .................................................................................... 49

Using the Leading Bass Function ........................................................................................50

A Simple Way to Make Automatic Accompaniment Settings (One Touch Program) ..................51

Using a Rhythm from a USB Memory.................................................................................. 52

Reviewing the Styles on USB Memory .......................................................................52

Copying Rhythms.............................................................................................................53

Deleting Saved Rhythm..................................................................................................... 55

Using the Registration Buttons .............................................................. 56

Storing Registrations......................................................................................................... 57

Recalling a Registration .................................................................................................... 58

How to Recall a Registration .................................................................................... 58

Changing the Timing of Recalling Registrations ..........................................................58

Automatically Registering When You Switch Panel Settings ...................................................59

Assigning a Name to a Registration Set.............................................................................. 59

Saving Registration Sets.................................................................................................... 61

Loading Previously Saved Registration Sets Into the ATELIER ..................................................63

Loading a Set of Registrations .................................................................................. 63

Loading an Individual Registration ............................................................................64

Deleting a Set of Registrations ........................................................................................... 65

Copying Registrations ......................................................................................................66

Using the Performance Functions .......................................................... 68

Transposing to a Different Key (Key Transpose) ...................................................................68

Using the Foot Switch....................................................................................................... 69

Changing the Function of the Foot Switch .................................................................. 70

Using the Foot Switch to Switch Registrations (Registration Shift)................................... 71

Adjusting the Overall Volume Using an Expression Pedal...................................................... 72

Adding Various Effects to a Voice......................................................... 73

Adding Harmony to a Melody (Harmony Intelligence) .......................................................... 73

Changing the Type of Harmony Intelligence............................................................... 74

Adding Modulation to the Sound (Rotary Effect)................................................................... 75

Sustain Effect................................................................................................................... 76

Changing the Sustain Length.................................................................................... 77

Reverb Effect ...................................................................................................................78

Changing the Reverb Type....................................................................................... 79

Changing the Wall Type ......................................................................................... 80

Changing the Depth of the Reverb ............................................................................ 81

Contents

Record and Playback Your Performance ............................................... 82

What is a Track Button? ..........................................................................................82

Playing Back Performance Songs Stored on USB Memory and SMF Music Files....................... 83

Silencing a Specific Track (Track Mute) ..............................................................................84

Recording a Performance.................................................................................................. 84

Playing Back a Performance Song .....................................................................................85

Add a Count Sound to Match the Timing (Count In)..............................................................86

Recording Each Part Separately......................................................................................... 86

Re-Recording................................................................................................................... 87

Erasing a Performance Song ............................................................................................. 87

Changing the Name of a Performance Song (Rename)......................................................... 88

Saving Performance Songs ...............................................................................................89

Loading Performance Songs Into the ATELIER....................................................................... 90

Deleting Performance Songs Stored on “Favorites” or the USB Memory ..................................91

Layering a New Recording onto SMF Music Files ................................................................92

Using Song with a Different Tempo Than That of the Performance Song..................................93

Copying Performance Song ..............................................................................................94

Enjoying VIMA TUNES Songs ...........................................................................................95

Listening to a VIMA TUNES Song .............................................................................95

Performing with Sounds that Match the Song (Recommended Tones)............................. 95

Listening to Songs from Music CD ...................................................................................... 96

Enjoying Karaoke with a Music CD (Center Cancel) ...................................................96

Transposing the Song to a Comfortable Key for Singing .............................................. 97

Various Other Settings ......................................................................... 98

Folder Settings.................................................................................................................98

Creating a Folder in USB Memory or User Memory ....................................................98

Changing the Name of a Folder...............................................................................98

Adjusting How the Instrument Responds.............................................................................. 99

Adjusting the Initial Touch Sensitivity (Initial Touch) .....................................................99

Changing the Pedalboard Polyphony (Pedal Bass Mode)............................................. 99

Changing How the Solo Voice Responds (Solo Mode) ..............................................100

Performance Function Settings ......................................................................................... 100

Changing the Function of the Expression Pedal (Exp. Source)..................................... 100

Rhythm Settings .............................................................................................................101

Preventing Rhythm Tempos from Switching Automatically (Auto Std Tempo) .................101

Changing the Sound of the Countdown (Count Down Sound)..................................... 102

Registration Settings .......................................................................................................102

Registration Arranger Update (Arranger Update)......................................................102

Registration Transpose Update (Trans. Update) ........................................................103

Composer Settings .........................................................................................................103

Switching the Display of Lyrics On or Off (Lyrics)...................................................... 103

Changing the Key When Playing Back Songs (Playback Transpose)............................ 104

Changing the Metronome Setting (Metronome) ........................................................104

Adjusting the Metronome Volume (Metronome Volume)............................................. 105

Changing the Sound of the Metronome (Metronome Sound) ......................................105

Setting the Beat (Beat) ........................................................................................... 106

Silencing a Specific Track (Track Mute) ................................................................... 106

Muting Individual Channels of Performance Data (Channel Mute)...............................107

Setting the Type of CD To Be Played Back (CD/Audio Type)...................................... 108

Contents

Adjusting the Timing of a Player Piano CD’s Piano Sound and Accompaniment

(CD/Audio Sync).................................................................................................. 108

Other Settings ...............................................................................................................109

Adjust the Standard Pitch (Master Tune)................................................................... 109

Specifying Transmission of PC Numbers (Send PC Switch)......................................... 109

Setting PC Numbers (PC Number) ..........................................................................110

MIDI IN Mode...................................................................................................... 110

Selecting the MIDI Transmit Channel (TxMIDI Channel).............................................. 111

Using the V-LINK function (V-LINK) .......................................................................... 112

Restoring the User Memory to the Original Factory Settings (User Memory Reset)................... 114

Restoring All Settings Other Than the User Memory to the Original Factory Settings

(Panel Reset) .................................................................................................................114

Formatting a USB Memory (Format)..................................................................................115

Connecting with External Devices ....................................................... 116

Names and Functions of Jacks and Connectors .................................................................116

Connecting Audio Equipment ..........................................................................................116

Making the Connections........................................................................................116

Connecting a Computer.................................................................................................. 117

Making the Settings for the USB Driver .................................................................... 118

Connecting MIDI Devices................................................................................................118

Making the Connections........................................................................................119

Appendices

Troubleshooting............................................................................................................. 120

Error Message...............................................................................................................125

Chord List ..................................................................................................................... 126

Glossary....................................................................................................................... 128

Music Files That the ATELIER Can Use............................................................................... 129

The ATELIER Allows You To Use the Following Music Files.......................................... 129

About the ATELIER Sound Generator ....................................................................... 129

Settings That Are Stored After the Power Is Turned Off........................................................ 130

Settings That Are Stored After the Power is Turned Off ..............................................130

Settings That Are Stored In the Registration Buttons ................................................... 130

Settings That Are Stored In the Individual Registration Buttons.....................................130

MIDI Implementation Chart .............................................................................................131

Main Specifications .......................................................................................................132

Demo Song List.............................................................................................................. 134

Profile .................................................................................................................134

Index............................................................................................................................ 135

Panel Descriptions

3 45 6 7

10 11 12 16

13 14

1718

[Power On] switch ( → p. 16)

[Master Volume] knob ( → p. 17)

Harmonic Bars ( → p. 28)

Pedal Bass Voice Select buttons ( → p. 25)

Pedal Part [To Lower] button ( → p. 36, p. 40) Level [▲] [▼] buttons ( → p. 34)

Lower Voice Select buttons ( → p. 25)

Lower part Level [▲] [▼] buttons ( → p. 34)

Upper Voice Select buttons ( → p. 25)

Upper part Level [▲] [▼] buttons ( → p. 34)

Solo Voice Select buttons ( → p. 26)

Solo part Level [▲] [▼] buttons ( → p. 34)

[One Touch Program] button ( → p. 51)

[Harmony Intelligence] button( → p. 73)

10.

Part Balance [▲] [▼] buttons ( → p. 34, p. 78) Vintage Organ buttons ( → p. 28)

11.

12.

Lower [Drums/SFX] button ( → p. 36) Transpose [-] [+] buttons ( → p. 68)

13.

14.

[Utility] button ( → p. 98) [Display/Exit] button ( → p. 21)

Menu [ ][ ] buttons Value [-] [+] buttons

15.

Display ( → p. 21)

Panel Descriptions

Write Manual

1 2 3 4

[Load] button ( → p. 63, p. 87, p. 92)

16.

17.

[Save] button ( → p. 61, p. 89)

18.

Beat Indicator ( → p. 46)

19.

Composer ( → p. 82)

[Song] button [Registration] button [Media] button

[Bass] button [Lower] button [Solo/Upper] button

[Reset] button [Play/Stop] button [Rec] button [Bwd] button [Fwd] button

Rhythm Select buttons ( → p. 41)

20.

Tempo [ ] [ ] buttons ( → p. 46) Arranger [On/Off] button ( → p. 47) [Auto Fill in] button ( → p. 48) Variation [1]–[4]buttons ( → p. 48) [Intro/Ending] button ( → p. 43) [Start/Stop] button ( → p. 45)

21.

Rotary Sound buttons ( → p. 75)

[On/Off] button [Fast/Slow] button

22.

Registration buttons

[Write] button ( → p. 57) [Manual] button ( → p. 59) Registration [1]–[4] buttons ( → p. 56)

Before You Start Playing

NOTE

Setting Up the Music Rest

fig.01-03

Attach the music rest by inserting it into the two holes.

Connecting the Power Cord

First, make sure that the [Power On] switch is

OFF (not pushed in).

fig. 00-27.eps,fig.00-27-2.eps

Turning the Power On and Off

941

Once the connections have been completed, turn on or off power to your various devices in the order specified. By turning on or off devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices.

Turning On the Power

Make sure of the following before the power is turned on.

• Is the power cord correctly connected to the AC inlet?

• Is the power cord correctly connected to the AC outlet?

• Is the [Master Volume] knob set to the Min (minimum) position?

fig.00-26.eps

Upper position

OFF

Connect the supplied power cord to the AC Inlet, then plug the other end into an AC outlet.

Power Cord

Only use the power cord supplied with this instrument.

NOTE

Whenever you do not intend to use the instrument for

NOTE

extended periods of time, pull out the power cord from the AC outlet.

AC Outlet

Press the [Power On] switch to turn on the

power.

fig. 00-27.eps, fig.00-27-3.eps

Lower position

The basic screen will appear in the display.

942

The ATELIER is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the ATELIER will operate normally.

Adjust the volume to an appropriate level by

moving the [Master Volume] knob or operating the expression pedal.

Turning the [Master Volume] knob towards “Max” increases the volume; turning the knob towards “Min” decreases the volume. Likewise, pressing down on the expression pedal increases the volume, while easing up on the pedal decreases the volume.

fig.00-28.eps

Before You Start Playing

Using Headphones

The ATELIER features Phones jacks. These allow you to play without having to worry about bothering others around you, even at night.

fig.00-29.eps

Before You Start Playing

decrease the volume

increase the volume

Turning Off the Power

Before switching the power off, set the [Master Volume] knob to the Min (minimum) position.

Press the [Power On] switch to turn off the

power.

fig. 00-27.eps,fig.00-27-2.eps

Connect your headphones to the Phones jack

underneath the left side of the keyboard.

The sound from the built-in speakers stops. Now, sound is heard only through the headphones.

fig.00-30.eps

Adjust the headphones volume with the

[Master Volume] knob and Expression pedal.

Some Notes on Using Headphones

• To prevent damage to the cord, handle the headphones only by the headset or the plug.

Upper position

OFF

945

If you need to turn off the power completely, first turn off the [Power On] switch, then unplug the power cord from the

NOTE

power outlet. Refer to “Power Supply” (p. 6).

• Headphones may be damaged if the volume is too high when they are plugged in. Lower the volume on the ATELIER before plugging in headphones.

• To prevent possible auditory damage, loss of hearing, or damage to the headphones, the headphones should not be used at an excessively high volume. Use the headphones at a moderate volume level.

• Accepts connection of Stereo headphones.

• If plugs of the headphones are plugged into the Phones jack, no sound will be heard from the ATELIER’s speakers.

Before You Start Playing

NOTE

Using the Cord Hook

If you’re using headphones, you can use the cord hook to neatly bundle the cables near your feet.

Attaching the Cord Hook

Screw the cord hook (with wing nut) about

80% of the way into the screw hole located at the bottom left of the ATELIER.

After you’ve oriented the hook as desired, use

the wing nut to fasten it.

Screwhole

Wing Nut

Do not turn off the power while the following screen is displayed.

fig.01-16

When factory reset is completed, the basic screen appears.

To return all settings other than the User memory settings to their original factory conditions, refer to “Panel Reset“ (p.

114).

Loading factory default settings will erase any Registrations currently in the memory of the ATELIER.To save the Registrations you are currently using, refer to “Saving Registration Sets” (p. 61).

To return only the User memory settings to their original factory conditions, refer to “User Memory Reset“(p. 114).

Cord hook

Restoring All the Factory Default Settings (Factory Reset)

The settings stored in the ATELIER can be returned to their factory settings. This function is called “Factory Reset.”

Turn down the volume to the minimum level, then turn off the power.

While holding down the [One Touch Program] button, press the [Power On] switch to turn the

power on.

fig.01-15

Adjusting the Contrast of the Screen

You can adjust the contrast of the screen.

Turn the [LCD Contrast] knob (p. 116) located

at the bottom of the ATELIER to adjust the contrast of the screen.

Bright Dark

Using the External Memory

NOTE NOTE

Songs you record on the ATELIER and Registration sets you create can be copied to separately available USB memory for safekeeping. You can also copy songs to a floppy disk using a separately sold floppy disk drive (p. 53, p. 66, p. 94).

You can also play back SMF music files saved on USB memory or a floppy disk (p. 83).

Use USB memory and floppy disk drive available from Roland. Proper operation cannot be guaranteed if other USB

NOTE

device is used.

If you’re using new USB memory or floppy disk, you’ll need to initialize (format) it on the ATELIER. For details, refer to “Formatting a USB Memory (Format)” (p. 115).

Before You Start Playing

Grasp the External Memory connector holder

and turn it 90 degrees to the left or right.

External Memory Connector Holder

90 degrees to the left

90 degrees to the right

Security Slot

Before You Start Playing

Connecting the USB Memory

Connect the USB memory to the External

Memory connector.

931

Carefully insert the USB memory all the way in—until it is firmly in place.

Rotating the External Memory Connector Holder

The External Memory connector holder rotates 90 degrees left and right. Rotating the External Memory connector holder allows you to avoid damaging the connected External Memory if something happens to bump against it.

Be sure to grasp the External Memory connector holder itself when rotating it. Never rotate the External Memory connector holder by holding the connected USB memory.

Take care not to allow your fingers to become pinched when rotating the External Memory connector holder.

988

Security Slot ( ) http://www.kensington.com/

Connecting the Floppy Disk Drive (Sold Separately)

Attach the floppy disk drive as shown the

figure, using the mounting holes on the ATELIER’s bottom panel.

For details of the attachment, refer to the owner’s manual of the floppy disk drive.

Connect the USB cable of the floppy disk drive to the ATELIER’s External Memory connector.

External Memory Connector

USB Cable

Before You Start Playing

NOTE

Using a CD

You can connect a commercially available CD drive and play back audio CDs and CD-ROMs containing saved SMF music files.

You can also play songs on VIMA CD-ROMs (VIMA TUNES) sold by Roland.

Precautions Concerning Use of the CD

• The ATELIER is capable of playing back only commercial CDs that conform the official standards-those that carry the “COMPACT disc DIGITAL AUDIO” logo.

Turn on the power to the ATELIER.

Turn on the power to the connected CD drive.

For information on how to perform the following CD-drive operations, refer to the owner’s manual for the drive.

• Switching the power on and off

• Inserting and ejecting a CD

A list of the CD drives that have been tested and found to be compatible is available on the Roland website.

http://www.roland.com/

About the Adjuster

• The usability and sound quality of audio discs that incorporate copyright protection technology and other non-standard CDs cannot be guaranteed.

• For more detailed information on audio discs featuring copyright protection technology and other non-standard CDs, please consult the disc vendor.

• You cannot save songs to CDs, and you cannot delete songs recorded to CDs. Furthermore, you cannot format CDs.

Connecting a CD Drive (Sold Separately)

The ATELIER does not support CD drives that are powered by the USB bus. If you use a USB-bus-powered CD drive,

NOTE

you must use the power supply included with the CD drive so that the drive will operate under its own power.

External Memory connector

USB cable

If you feel that the ATELIER has become unstable, for example after moving it to another location, turn the adjuster located on the bottom of the stand’s legs as shown in the following.

When turning the adjuster, be careful not to pinch your hand.

• Rotate the adjustor to lower it so that it is in firm contact with the floor. Make adjustments so that there is no gap between the adjuster and the floor. In particular, when placing the ATELIER on carpet, turn the adjuster so that it is firmly in contact with the floor.

Switch off the power to the ATELIER and the CD drive to be connected.

Connect the USB cable included with the CD

drive to the External Memory connector on the ATELIER.

About the Display

The ATELIER has three types of basic screen: the Rhythm Screen, the Composer Screen and the Registration Screen. You can alternate from one to the other by pressing the [Display/Exit] button.

fig.01-17

Basic Screens

Rhythm Screen

fig.01-18

Tempo

MeasureBeat

About the Display

Chord Name

Composer Screen

When internal music data is selected:

fig.01-19

Tempo

Chord Name

Registration Screen

Rhythm Name

MeasureBeat

Song Name

fig.01-20

Tempo

Chord Name

MeasureBeat

Registration Name

Next Registration Set Name

Refer to “Load Next Function” (p. 71).

Selecting and Playing Sounds

Listening to the Demo Songs

The ATELIER contains 6 Demo songs. Here’s how to play the Demo songs, and fully appreciate the sounds, Rhythms, and Automatic Accompaniment that are available with the ATELIER.

fig.02-01

1, 5

NOTE

Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws.

NOTE

The data for the Demo song that is being played is not available at the MIDI Out connector.

fig.02-02

3, 4

Press the [Song] button and [Registration] button simultaneously.

Press the Value [-] [+] buttons to select a Demo song.

Press the [Play/Stop] button to start playback of the demo song.

When the selected demo song ends, the next demo song will begin playing.

To stop playback in the middle of the song, press the [Play/ Stop] button.

Check out the “Demo Song List” (p. 114) for information such as the names of the composers and players of the demo songs.

Press the [Song] button and [Registration] button simultaneously to exit the demonstration screen.

If the following screen appears

If the performance song in the ATELIER has not been saved to a USB memory or Favorites (User memory), the following message will appear, and it will not be possible to play the Demo songs.

fig.02-03

Selecting and Playing Sounds

If you don’t mind erasing this song, press the [Rec] button. However, if you wish to save this song, press the [Reset] button to cancel the procedure, and then save the song onto a USB memory or Favorites (User memory).

Selecting and Playing Sounds

If you wish to save the performance data, refer to “Saving Performance Songs” (p. 89)

Selecting and Playing Sounds

Selecting Voices

The ATELIER is able to produce the sounds of various instruments. These sounds are called “Voices.”

About the Voices and Parts

The ATELIER has two keyboards and one Pedalboard, as shown below. From top to bottom these are called the “Upper Keyboard,” “Lower

Keyboard,” and “Pedalboard.”

fig.02-04

Upper Keyboard

Lower Keyboard

Pedalboard

The Upper Keyboard has three parts: “Upper,” “Solo“ and “Vintage Organ.” You can select one voice for each part, meaning that it is possible to layer the voices on Upper Keyboard and play them simultaneously.

The Lower Keyboard has two parts: “Lower” and “Vintage Organ.“ The Pedalboard has the part: “Pedal.”

Keyboard

Upper Keyboard

Lower Keyboard

Pedalboard

Upper

Upper Vintage

Solo

Lower

Lower Vintage

Pedal (This voice is sounded when the Pedal [To Lower] button lights up or ”Bass Split” is at on

Pedal

Part

Functions of the Upper/Lower/Pedal Bass Sound Select Buttons

fig.02-05

Each time you press a voice button, its indicator will switch between being lit and being turned off. Voices that have their button indicator lit can be played.

Selecting the Upper/Lower/Pedal Bass Voices

Selecting and Playing Sounds

NOTE

If none of the voice buttons or Vintage organ buttons are lit, playing the keyboard will not produce a sound.

Selecting and Playing Sounds

Select voices by pressing the Upper, Lower and Pedal Bass Voice Part buttons.

When the power is turned on, the Upper keyboard will play “Full Organ 3,” the Lower keyboard will play “Lower Organ2” and the Pedal Bass voice will sound single notes using the “Organ Bass1” voice.

Example: Selecting “Orch.Brs Ens” for the Upper Organ Part

fig.02-06

Press the Upper [Brass] button (indicator lights).

The name of the selected voice appears in the display for several seconds.

Now when you play the Upper keyboard, the “Orch.Brs Ens” will sound. You can select the Lower Voice or Pedal Bass Voice in the same way as the

Upper Voice.

NOTE

If you press the Pedal [To Lower] button (indicator lights p. 40), the Pedal Bass voice can now be played by the Lower keyboard, not by the Pedalboard.

Settings can be adjusted to allow multiple notes to be played on the Pedalboard (p.

99).

Selecting and Playing Sounds

Selecting Solo Voice

The Solo section of the Upper keyboard is monophonic, that is, the Solo voice will only sound for the highest note played on the Upper keyboard.

fig.02-11

Example: Selecting “Tenor” for the Solo Voice Part

fig.02-12

Press the Solo [Sax] button (indicator lights).

The name of the selected voice appears in the display for a few seconds.

Play the Upper keyboard. The selected voice will sound by the highest note played.

It is possible to change how a Solo voice will sound. Normally, the Solo voice will be sounded by the highest note

ou play on the Upper keyboard, but you can make settings so that the last-played note will sound the Solo voice. You can also make settings so that the Solo voice will be sounded by all notes of the keyboard to which the Solo voice is assigned. For details refer to “Changing How the Solo Voice Responds (Solo Mode)” (p. 100).

Selecting a Voice Using the [Others] Button

Notice that there is an [Others] button for each part. By using the [Others] button, you can select all voices.

fig.02-10 (P.29)

Press the [Others] button for the Part for which you wish to specify a voice.

The voice name appears in the display.

The indicator of the selected [Others] button will light.

Selecting and Playing Sounds

You can jump by voice group

by pressing Menu [ ] [ ] buttons to select the voice.

The sound number of each voice is preceded by an alphabetical character which indicates the sound group; e.g., “G11 Strings1.”

Selecting and Playing Sounds

While the voice name is shown in the display screen, use the Value [-] [+] buttons to select the desired voice.

The indicator of the selected [Others] button will blink. To stop mid-way through this or any procedure, press the [Display/Exit]

button.

Once again, press the [Others] button for the part whose sound you wish to set to confirm the voice.

The indicator of the [Others] button will change from blinking to light.

You can also press the key for the part containing a changed voice to confirm the voice setting.

About the voices that can be assigned to an [Others] button, please refer to ”Voice & Rhythm List.”

Selecting and Playing Sounds

Creating Organ Sounds (Vintage Organ)

The Vintage Organ buttons lets you add vintage organ sounds to the upper and lower parts. In addition, you can also use the harmonic bars to modify the selected sound as desired.

The ATELIER provides nine harmonic bars for the upper part and lower part. Each harmonic bar is assigned a sound of a different footage (pitch), and by

layering these sounds you can create a variety of organ tones.

Harmonic Bar

By sliding the harmonic bars forward or backward (in or out), you can adjust the volume of the various footages.

The volume can be adjusted over nine steps (0–8). When a harmonic bar is pulled out all the way (8), the volume is loudest.

When it is pushed in all the way (0), there will be no sound.

8' is the footage that forms the basic pitch of the sound; this is the center around which you create the tone.

Each harmonic bar is assigned a sine wave (a pure pitch without overtones) of a different pitch, and by combining these pitches you can create a wide range of sounds.

8' volume: 8

4' volume: 5

Time

What’s the feet?

“Feet” is a term that began as a measurement of the length of the pipes in a pipe organ.

The pipes that produce the basic pitch (fundamental) for each note are considered to be “8 feet” in length.

Therefore, a pipe producing a pitch one octave below that of the reference of 8' (eight feet) would be 16'; for one octave above the reference, the pipe would be 4', and to take the pitch up yet another octave it would be shortened to 2'.

The pitches of the harmonic bars are related as follows.

When the middle C (C4) note is pressed, each

harmonic bar will sound the following notes.

Selecting and Playing Sounds

16' 8' 4' 2' 1'51/3'2

one octave

below

5th root 8th 12th

8' =

/3'1

15th

/5'11/3'

17th 19th 22nd

On tonewheel organs, the high-pitched footage for a portion of the high range, and the low-pitched footage for a portion of the low range are “folded-back” in units of one octave.

Folding back the high-frequency portion prevents the high-frequency sounds from being unpleasantly shrill, and folding back the lowfrequency portion prevents the sound from becoming “muddy.”

On the ATELIER faithfully simulates this characteristic.

Selecting and Playing Sounds

Playing a Vintage Organ Voice

Turning on the Vintage Organ

fig.01-24.eps

Press the Vintage Organ [On/Off] button so its indicator is lit.

Each time you press the button, the indicator will alternate between ON (lit) and OFF.

The Vintage organ screen appears.

The screen will show When a harmonic bar is pulled out all the way (8), the volume is loudest.

When it is pushed in all the way (0), there will be no sound.

value

for the harmonic bars.

NOTE

Glide and sustain effects are not applied to the Vintage Organ voice.

The Vintage Organ screen will be displayed for several seconds, then it will close automatically.

Modifying the Sound

Press H-Bar Part [Upper] or [Lower] button to select a part for which the harmonic bars are available.

Slide the harmonic bars that you want to hear.

You can layer the sound of multiple harmonic bars.

Adding Sparkle to the Sound (Percussion)

This adds an attack sound to the beginning of the note, making the sound crisper.

Selecting and Playing Sounds

Press the Percussion [2 2/3'] button so its indicator is lit.

Play the Upper keyboard and notice that an attack has been added.

Button

Percussion [2 2/3'] button

Percussion one octave and a fifth above

Explanation

Adjusting the Rate at which the Percussion Decays

You can shorten the decay time of the percussion sound.

Press the Percussion [Fast Decay] button to switch the indicator between lit/unlit.

NOTE

The Percussion [2 2/3'] button are valid only for vintage organ voices of the upper part.

Selecting and Playing Sounds

NOTE

When the Percussion [2 2/3'] button is on, the 1' pitch will not be produced.

[Fast Decay] Button

Lit

Unlit

The percussion sound will disappear quickly. The percussion will have a sharper attack.

The percussion sound will disappear slowly. The percussion will have a more gentle attack.

Explanation

Using the Harmonic Bar Settings of the Panel

If you’ve switched Registrations so that the Vintage Organ settings have changed, you can switch the Vintage Organ settings to the positions (settings) of the harmonic bars on the panel.

Press the H-Bar Part [Upper] or [Lower] button whose indicator is lit.

The part whose indicator is lit will have the settings of the harmonic bar positions (settings) of the panel.

Selecting and Playing Sounds

Adjusting the Volume of the Vintage Organ

You can adjust the volume of the Vintage Organ sound to regulate the volume balance relative to the other sounds.

fig.05-08.eps

fig.VoiceList.eps

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “VintageOrganVolume.”

Press the Value [-] [+] buttons to select the value for volume of the vintage organ.

Setting

0–12

To return to the basic screen, press the [Utility] button.

Performing with an Active Expression Voice

For “Active Expression Voices,” operating the expression pedal will control not only the volume but also the tone, or may add additional sounds.

Selecting and Playing Sounds

Press the [Others] button of the Part to which you want to assign an Active Expression voice.

The voice name appears in the display.

The indicator of the selected [Others] button will light.

Press the Value [-] [+] buttons to select the Active Expression Voice.

The indicator of the selected [Others] button will blink.

Active Expression Voices have the letters “AEx” preceding their voice name.

Selecting and Playing Sounds

For details on the Active Expression voices that are available, refer to “Voice list” (Appendix: separate booklet).

To stop mid-way through this or any procedure, press the [Display/Exit] button.

Once again, press the [Others] button for the part whose sound you wish to set to confirm the voice.

The indicator of the [Others] button will change from blinking to light.

You can press the key for the part containing a changed voice to confirm the voice setting.

Selecting and Playing Sounds

Adjust the Volume Balance

The ATELIER allows you to adjust the volume balance individually for each Part.

fig.02-13

The following buttons are used to adjust the volume of a multiple number of Parts.

Button

Part

fig.02-14

Automatic Accompaniment (except Bass)

Playback of performance songs from

Accomp/SMF [▲] [▼] button

Pedal Level [▲] [▼] button

something other than the ATELIER performance songs (for example: SMF music files)

Rhythm performance

Drums/SFX

Pedal voice

Bass note of Automatic Accompaniment

The volume levels of each part are adjusted using the corresponding [▲] and [▼] buttons.

Pressing the [▲] button will increase the volume. Pressing the [▼] button will decrease the volume. The volume can be set to any value from 0 to 12. When the volume value shown in the display is 0, that part will produce no

sound. You can also press the [▲] button or [▼] button of the part whose volume you

wish to adjust, so that the “Part Balance Monitor” screen is displayed for several seconds, allowing you to check the volume balance.

R Reverb A Accomp/SMF P Pedal L Lower U Upper S Solo

The Part Balance Monitor screen is displayed for several seconds and then closes automatically.

Selecting and Playing Sounds

Transpose the Pitch in Octave Units (Octave Shift)

The pitch of the sound played by the keyboard can be adjusted in one-octave steps. This function is called “Octave Shift.” You can apply an Octave shift to the following 4 Parts:

• The Upper Part

• The Lower Part

• The Pedal bass Part

• The Solo Part

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Octave Shift.”

Press the [Rec] button.

Use the Menu [ ] [ ] buttons to select a Part to which you wish to apply an Octave Shift.

Selecting and Playing Sounds

fig.02-16

Part

Pedal, Lower, Upper, Solo

Use the Value [-] [+] buttons to set the amount of shift.

The value can be set to a range of +/- 3 octaves.

To return to the basic screen, press the [Utility] button.

NOTE

Please note that when you apply the Octave Shift function to certain voices, their pitch could be stretched beyond their recommended note ranges, and they may not sound as expected. Care should be taken when using Octave Shift.

Selecting and Playing Sounds

Sustaining Notes Played on the Lower Keyboard

You can have the sound for keys in the Lower keyboard continue to play, even after you release the key, until the next key is pressed.

Hold down the Pedal [To Lower] button for several seconds until its indicator begins blinking.

The following message will appear.

The notes played on the lower keyboard will continue sounding.

This setting is saved to the

Registration.

Pedal [To Lower] button will

also turn on at this time.

Press the Pedal [To Lower] button so its indicator goes out.

The sound stops playing.

Playing Drums from the Entire Lower Keyboard (Drums/SFX)

You can use the Lower keyboard to play various drum sounds (drum set). In this case, the Lower voices will no longer sound.

fig.02-18

Refer to for “Voice & Rhythm List” (Appendix: separate booklet) details on which drum sound or Sound Effect will be

Press the [Drums/SFX] button (indicator lights).

Play the Lower keyboard and listen to the various drum sounds on each key. The [Drums/SFX] button will alternate between on (lit) and off each time it is

pressed.

played by each note.

Selecting and Playing Sounds

Changing the Drums/SFX Set

Immediately after the power is turned on, the STANDARD drum set will sound. Let’s try selecting a different Drum Set or the Sound Effect set. As the drum set, you can choose from 7 types of drum set. When you change

the drum set, the sound produced by each note will change.

fig.02-19

1, 3

Press the [Drums/SFX] button (indicator lights).

When the Drum Set name is displayed on the screen, press the Value [-] [+] buttons to select a Drum Set or Sound Effect

NOTE

For some drum sets, there will be keys that do not sound.

Selecting and Playing Sounds

Refer to “Voice & Rhythm List” (Appendix: separate booklet) for details on which drum sound or Sound Effect will be played by each note.

fig.02-20

Set.

The [Drums/SFX] button indicator will begin to blink.

You can select from 6 different Drum Sets and one set of Sound Effects as follows:

Drum Sets

STANDARD, POWER, ELECTRONIC, JAZZ, BRUSH, ORCHESTRA, SOUND EFFECTS

To stop mid-way through this or any procedure, press the [Display/Exit] button.

Press the [Drums/SFX] button once again.

The [Drums/SFX] button indicator will light constantly, and the selected Drums/SFX set will be applied.

You can also play the lower manual to confirm the drum set.

Selecting and Playing Sounds

Using the Lower Keyboard to Play the Bass Voice (Bass Split)

By using the Bass Split function you can play the bass voice in the left-hand side (including C3) of the lower keyboard. The location at which the lower keyboard is divided in this way, to play the pedal bass voice, is called the “Bass Split Point.”

The bass split point is included

in the left-hand area of the

Select a Pedal Bass voice (p. 25).

keyboard.

fig.06-16.eps

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Bass Split.”

Use the Value [-] [+] buttons to change the “Bass Split” setting to “ON.”

When you play the Lower keyboard, the Pedal Bass voice will sound in the range to the left of (and including) the C3 note.

Pedal Bass

voice

Bass Split Point

Lower keyboard

NOTE

It is not possible to select and

play both Bass Split function

and Pedal [To Lower] button

(p. 40) simultaneously.

You can adjust the Bass Split Point (p. 39).

NOTE

If the ”Bass Split” function is on, the Pedal Bass voice will not be heard from the Pedalboard. The Pedal Bass voice will sound from the Lower keyboard.

To return to the basic screen, press the [Utility] button.

Changing the Bass Split Point

You can assign the Bass Split Point (the highest key up to which the Pedal Bass voice will sound), to any key of the Lower keyboard.

Selecting and Playing Sounds

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Bass Split Point.”

Press the Value [-] [+] buttons to modify the Bass Split Point.

Setting

C2–C6

To return to the basic screen, press the [Utility] button.

Selecting and Playing Sounds

By pressing the Value [-] [+] buttons simultaneously, you can restore the default setting (C3).

Selecting and Playing Sounds

Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] button)

By using the Pedal [To Lower] button, you can sound the Pedal Bass voice by playing the root note (p. 128) of a chord on the Lower keyboard in the area that is playing the Lower voice.

fig.05-08

Select a Pedal Bass voice (p. 25).

NOTE

If no portion of the Lower keyboard is sounding the Lower voice (the [Drums/SFX] button is ON), the Pedal Bass voice will not sound.

NOTE

If the Pedal [To Lower] button is ON, the Pedal Bass voice will not be heard from the Pedalboard.

Press the Pedal [To Lower] button (indicator lit).

When you play a chord in the area of the Lower keyboard that sounds the Lower voice, the Pedal Bass voice will also be heard and will play the root note.

If the “Leading Bass” function is on (p. 50), the lowest note played in the lower keyboard will sound the pedal bass voice.

NOTE

It is not possible to select and play both Bass Split function (p. 38) and Pedal [To Lower] button simultaneously.

If no voice is selected for the lower keyboard, you can use the lower keyboard to play the pedal voice.

Using the Rhythm Performance

The ATELIER lets you enjoy playing along with a rhythmic accompaniment.

Selecting a Rhythm

fig.03-01

The AT-75 provides 40 types of Rhythms and Automatic Accompaniments (Music Styles). These are organized into eight groups.

Each Rhythm button corresponds to two groups. By pressing a button that is lit, you can select that button’s other group. The selected group is shown by the illumination status of the two indicators

located beside the Rhythm buttons.

Indicators located beside

the Rhythm buttons

The Rhythm group printed above the button is selected.

Upper indicator lit

Lower indicator lit

If you’ve selected the “Big Band/Switch” group, the indicators shown below will light.

(Big Band/Swing, Country/Gospel, Oldies/ Contempo, Ballad)

The Rhythm group printed below the button is selected. (Latin, Waltz/March, Trad/Acoustic, User)

Description

For more on the internal Rhythms, refer to “Voice & Rhythm List” (Appendix: separate booklet).

Using the Rhythm Performance

fig.03-02

1, 3

Press a Rhythm button to select a Rhythm group.

The indicator of Rhythm button will light. That Rhythm will be shown in the display.

Press the Value [-] [+] buttons to select a different Rhythm within the same group.

The indicator of the Rhythm button will blink.

Press the flashing Rhythm button once more.

The Rhythm button’s indicator will change from blinking to light. The Rhythm has now been applied.

You can also apply the selected rhythm by starting the rhythm.

Using the Rhythm Performance

Using Rhythms Stored in User Memory

The ATELIER features a User memory.

What is User Memory?

“User Memory” refers to an area inside the instrument where you can store the Registration you create and the performances you record. Registration and SMF music files saved on USB memory can also be copied to User memory (p. 53).

User memory is quite useful, since anything you place there will be retained even while the power is turned off.

The following things are stored in User memory:

• Songs you’ve registered in “Favorites”

• Rhythms

• Registration sets

The ATELIER is shipped from the factory with Rhythms already stored in User memory. These Rhythms can be overwritten by copying. The content of User memory is retained even while the ATELIER’s power is turned off. You can call up Rhythms in User memory by selecting the User group.

Calling Up Rhythms Stored in User Memory

If you wish to copy a Rhythm saved on USB memory to User memory, refer to “Copying Rhythms” (p. 53).

If you want to restore the original Rhythms that User memory contained at the time the instrument was shipped from the factory, refer to “Restoring the User Memory to the Original Factory Settings (User Memory Reset)” (p. 114).

Press the Rhythm [Ballad/User] button a number of times to select the user group.

The Rhythm screen appears.

Press the [Media] button to select “User.”

The Rhythms stored in User memory will be shown.

Press the Value [-] [+] buttons to select a different Rhythm

If USB memory is connected,

ou can select “Ext Memory” so that Rhythms in the USB memory will be shown. If floppy disk is connected, you can select “Disk” so that Rhythms in the floppy disk will be shown.

within the same group.

The indicator of Rhythm [Ballad/User] button will blink.

After selecting a Rhythm, press the blinking Rhythm [Ballad/User] button once more.

The Rhythm [Ballad/User] button stops blinking and remains lit, indicating that the Rhythm has been selected.

Playing Rhythm

There are two ways to start the Rhythm. You can press the [Start/Stop] button to start the Rhythm, or you can use Sync Start to have the Rhythm start when you play the lower keyboard or the pedalboard.

You can also make the Rhythm start with an intro, or stop with an ending.

fig.02-03_AT-900.eps

Starting at the Press of a Button

Using the Rhythm Performance

The functions of the [Intro/ Ending] button and [Start/Stop] button can be assigned to the foot switches located on each side of the Expression Pedal (p.

70).

Using the Rhythm Performance

Starting with an Added Intro

Press the [Intro/Ending] button.

Press the [Start/Stop] button.

The Intro is played and the Rhythm starts.

While the Intro is playing, the [Intro/Ending] button indicator will light, until the Intro ends then the button indicator will go dark.

Starting Without an Intro

Press the [Start/Stop] button.

The Rhythm starts without an Intro being played.

Making the Intro Short and Simple

Press the Variation [1] button.

For more on the Variation buttons, refer to “Adding Variety to the Rhythm or Automatic Accompaniment” (p.

48).

Press the [Intro/Ending] button.

The [Intro/Ending] button indicator will light.

Press the [Start/Stop] button.

A short Intro is played and the Rhythm starts.

Using the Rhythm Performance

Starting the Rhythm Automatically When You Play the Lower Keyboard or Pedalboard (Sync Start)

Starting with an Added Intro

While holding down the Arranger [On/Off] button, press [Auto Fill In] button to turn Sync Start on.

The [Start/Stop] button indicator will blink.

Press the [Intro/Ending] button.

The [Intro/Ending] button indicator will light.

Play either the Lower keyboard or the pedalboard.

The Intro is played and the Rhythm starts.

While the Intro is playing, the [Intro/Ending] button indicator will light, until the Intro ends then the button indicator will go dark.

Starting Without an Intro

While holding down the Arranger [On/Off] button, press [Auto Fill In] button to turn Sync Start on.

The [Start/Stop] button indicator will blink.

NOTE

If the Arranger function is ON (the Arranger [On/Off] button indicator is lit), it is not be able to start the Rhythm by playing the Pedalboard (p. 47).

Play either the Lower keyboard or the pedalboard.

The Rhythm starts without an Intro being played.

Starting with the Intro Short and Simple

While holding down the Arranger [On/Off] button, press [Auto Fill In] button to turn Sync Start on.

The [Start/Stop] button indicator will blink.

Press the Variation [1] button.

Press the [Intro/Ending] button.

The [Intro/Ending] button indicator will light.

Play either the Lower keyboard or the pedalboard.

A short Intro is played and the Rhythm starts.

For more on the Variation button, refer to “Adding Variety to the Rhythm or Automatic Accompaniment” (p. 48).

Stopping the Rhythm

Using the Rhythm Performance

Stopping with an Ending

Press the [Intro/Ending] button.

An Ending is played, then the Rhythm stops.

While the Ending is playing, the [Intro/Ending] button indicator will light, until the Ending finishes the button indicator will be turned off.

Stopping without an Ending

Press the [Start/Stop] button.

The Rhythm stops without an Ending being played.

Stopping with the Ending Short and Simple

Press the Variation [1] button.

Press the [Intro/Ending] button.

A short Ending is played, then the Rhythm stops.

The functions of the [Intro/ Ending] button and [Start/Stop] button can be assigned to the foot switches located on each side of the Expression Pedal (p.

70).

Using the Rhythm Performance

Changing a Tempo of Rhythm and Automatic Accompaniment

fig.03-06(P.40)

You can change the tempo of the Rhythm or Automatic Accompaniment.

Press the Tempo [ ] [ ] buttons to change the tempo (speed) of the Rhythm or Automatic Accompaniment.

Tempo [ ] button

The value of the tempo currently set (20–500 beats per minute) can be checked in the display. You can also check the tempo by viewing the Beat indicator.

The tempo becomes slower

The tempo becomes faster

If you switch Rhythms when “Auto Std Tempo” (p. 101) is on, the tempo changes to match the Rhythm. If you switch Rhythms when “Auto Std Tempo” is off, the tempo remains unchanged even when

ou switch the Rhythm.

By pressing the Tempo [ ]

[ ] buttons simultaneously, the tempo is returned to the standard (preset) tempo for the selected Rhythm.

Playing a Countdown Sound When the Intro Ends

If an intro is played before your performance, you can have a countdown played to the end of the intro, allowing you to understand easily where you are to start playing.

Press the [Utility] button.

Using the Menu [ ] [ ] buttons a number of times to select “Intro Count Down.”

Press the Value [-] [+] buttons to switch the Intro Count Down “ON” or “OFF.”

Press the [Intro/Ending] button.

Press the [Start/Stop] button.

The intro plays, and a countdown plays to the end of the intro. When the Sync Start is on, specifying the chord on the Lower keyboard starts the intro, and again, a countdown is given.

You can adjust the volume of the Countdown Sound, refer to “Adjusting the Metronome Volume (Metronome Volume)” (p. 105).

You can change the countdown sound (p. 102).

To return to the basic screen, press the [Utility] button.

Playing Rhythm and Automatic Accompaniment

The Arranger function of the ATELIER can add an Automatic Accompaniment to each Rhythm. Based on the selected Rhythm, the Arranger function automatically adds an accompaniment that is suitable for the chord being pressed on the Lower keyboard.

fig.02-06.eps

Using the Rhythm Performance

Press the Arranger [On/Off] button (indicator lights).

Arranger [On/Off] button

Lit (On)

Unlit (Off)

Rhythm and Automatic Accompaniment

Rhythm

Function

Start the Rhythm (p. 43).

The Rhythm and the Automatic Accompaniment will play together.

If the Arranger [On/Off] button is ON and no Pedal Bass voice is selected, the Automatic Accompaniment will play the bass sound.

NOTE

When the Arranger [On/Off] button is on, Sync Start (p. 44) on the pedalboard cannot be used.

NOTE

When the Arranger [On/Off] button is on, the lower voice is not played during the performance of the intro and ending, even when the Lower keyboard is played.

Using the Rhythm Performance

Adding Variety to the Rhythm or Automatic Accompaniment

You can add variety to the Rhythm or Automatic Accompaniment by changing the Rhythm pattern.

fig.02-07_AT-900.eps

Button name

A fill-in will automatically be added when you press

[Auto Fill In] button

What’s a fill-in?

A Fill In is a short phrase that is inserted at a break in the melody or at a point where the character of the song changes (between Chorus’s or Verses).

a Variation [1]–[4] button to change the accompaniment or Rhythm arrangement.

Function

Changing the Arrangement of the Rhythm and Accompaniment (Variation)

You can change the arrangement of the accompaniment. This function is called “Variation.” For each Rhythm, there are four types of arrangement for the accompaniment. The following buttons are called Variation buttons.

fig.02-08_AT-900.eps

Press the Variation [1]–[4] buttons to change the arrangement of the accompaniment.

The indicator of the button you pressed will light. The Variation [1] button produces the simplest arrangement, and the [4] button produces the most florid. For an intro or ending, Variation [1] button is the shortest and simplest.

The functions of the Variation buttons can be assigned to the foot switches located on each side of the Expression Pedal. Please refer to “Changing the Function of the Foot Switch” (p.

70).

Turning Chord Intelligence On/Off

“Chord Intelligence” is a feature that intelligently plays the correct accompaniment chords the moment you play a key specifying a chord on the Lower keyboard during Automatic Accompaniment.

To play a C chord on the Lower keyboard, for example, you usually have to press down the three keys C, E, and G; but with Chord Intelligence, you only have to press the C Key to initiate a C chord accompaniment.

Press the [Utility] button.

Using the Rhythm Performance

For more information about chord fingering, see the “Chord List” (p. 126).

fig.12-29

Press the Menu [ ] [ ] buttons a number of times to select “Chord Intelligence.”

Press the Value [-] [+] buttons to switch the Chord Intelligence “ON” or “OFF.”

Setting

OFF

To return to the basic screen, press the [Utility] button.

Chord Intelligence function is ON.

Chord Intelligence function is OFF.

Description

Using the Rhythm Performance

When the [One Touch Program] button is pressed, the Chord Intelligence function is automatically switched ON.

When the Leading Bass function (p. 50) is on and the Chord Intelligence function is off, you can specify chords with a combination of the lower keyboard and pedalboard.

Using the Rhythm Performance

Using the Leading Bass Function

When Automatic Accompaniment is used, and the Pedal [To Lower] button is ON, the Pedal Bass voice will normally play the root note (p. 128) of the chord you play on the Lower keyboard. If the Leading Bass function is enabled, the lowest note of the chord you play on the Lower keyboard will then be used as the bass note (the bottom note of the chord).

For this reason, the bass note will be sounded differently than normal when you play an inverted chord (p. 128).

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Leading Bass.”

Press the Value [-] [+] buttons to switch the Leading Bass “ON” or “OFF.”

Setting

The Leading Bass function is ON.

OFF

To return to the basic screen, press the [Utility] button.

The pedal bass tone will sound the lowest note of the chord you play in the lower keyboard.

The Leading Bass function is OFF.

Description

You can assign the Leading Bass functions to either of the foot switches located on each side of the Expression Pedal (p.

70).

When the Leading Bass function is on and the Chord Intelligence function (p. 49) is off, you can specify chords with a combination of the lower keyboard and pedalboard.

Using the Rhythm Performance

A Simple Way to Make Automatic Accompaniment Settings (One Touch Program)

When using the Arranger function for Automatic Accompaniment, you can also use the “One Touch Program” function to automatically select panel settings that are appropriate for the selected Rhythm.

By pressing the [One Touch Program] button, you can make the following settings.

• Panel settings (e.g., sounds and volume) suitable for the Rhythm

• Automatic Accompaniment playing

• [Start/Stop] button blinking (Waiting for Sync Start)

• Chord Intelligence function is ON (p. 49)

Using the Rhythm Performance

What is Sync Start?

Sync Start is a function that starts the Rhythm at the moment that you play the lower keyboard.

What is Chord Intelligence?

“Chord Intelligence” is a feature that intelligently decides on accompaniment chords the moment you play some keys specifying a chord during Automatic Accompaniment.

Select a Rhythm (p. 41).

Press the [One Touch Program] button.

Panel settings appropriate for the Rhythm and Automatic Accompaniment will automatically be called up for Registration [1]–[4] buttons.

Press the Registration [1]–[4] buttons to select panel settings.

On the Lower keyboard, play a chord.

At the moment you play the keyboard, the Intro will begin, and then the Rhythm and Automatic Accompaniment will play.

NOTE

When you press the [One Touch Program] button, the “Arranger Update” setting will automatically change to “INSTANT” (p. 58).

Press the [Intro/Ending] or [Start/Stop] button to stop the Rhythm.

Rhythm and Automatic Accompaniment stops.

Press the [One Touch Program] button, extinguishing its indicator.

The One Touch Program function is turned off, and the panel settings in effect prior to the [One Touch Program] button being pressed are restored.

Using the Rhythm Performance

Using a Rhythm from a USB Memory

The ATELIER contains a variety of Rhythms, but you can also use Rhythms from USB memory or floppy disk to perform Rhythms in an even wider range of styles.

Reviewing the Styles on USB Memory

fig.02-21-1.eps

fig.02-21.eps

Connect the USB memory containing the Rhythms to the External Memory connector.

Press the Rhythm [Ballad/User] button a number of times to select “User group.”

The Rhythm screen appears.

Press the [Media] button to select “Ext Memory” and see the Rhythms in USB memory.

The Rhythm screen will show the Rhythms on the USB memory.

NOTE

Unauthorized use of commercially available Music Style disk for purposes other than private, personal enjoyment is a violation of applicable laws.

If you want to use Rhythms from a floppy disk, connect the floppy disk drive (sold separately) to the External Memory connector.

If “User” is selected, the Rhythms saved in User memory (p. 42) will be shown. If “Disk” is selected, the Rhythms saved on the floppy disk will be shown.

Press the Value [-] [+] buttons to select a Rhythm.

The [Start/Stop] button indicator will blink while the Rhythms are being loaded into internal memory. When loading is finished, you will be able to play the selected Rhythm.

Press the [Start/Stop] button.

The selected Rhythm is played.

If you copy Rhythms from USB memory or floppy disk into User memory (p. 42), you’ll be able to access those Rhythms simply by pressing the Rhythms [Ballad/User] button (p. 53).

Copying Rhythms

User memory (p. 42) already contains Rhythms, but you can replace these Rhythms with Rhythms from USB memory or floppy disk. Rhythms copied from the USB memory into User memory will not be lost even if the power is turned off. It is convenient to copy frequently-used Rhythms into User memory.

Copying Rhythms from USB Memory to User Memory

Using the Rhythm Performance

fig.02-09.eps

fig.02-10.eps

Connect the USB memory to the External Memory connector.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Media Utility.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Copy Rhythm.”

If you want to copy Rhythms from floppy disk, connect the floppy disk drive (sold separately) to the External Memory connector.

NOTE

If no USB memory or floppy disk is inserted, you won’t be able to choose “Copy Rhythm” in the Utility menu.

Using the Rhythm Performance

Press the [Rec] button.

Press the [Media] button to select the media (the location of the Rhythm you want to copy).

If you want to copy a Rhythm from USB memory, select “Ext Memory.” If you want to copy a Rhythm from floppy disk, select “Disk.”

Press the Value [-] [+] buttons to select the Rhythm you want to copy.

Using the Rhythm Performance

10.

11.

Press the [Rec] button.

Press the Value [-] [+] buttons to select the copy-destination number.

To cancel the procedure, press the [Display/Exit] button.

Press the [Rec] button to copy the Rhythm.

While the Rhythm is being copied into internal memory, the following screen will be displayed.

If you select a number in which a Rhythm is already saved, a screen like the following appears.

NOTE

Never remove the USB memory or turn off the power while the Rhythm data is being copied from USB memory into the

TELIER. If you do so, the

Rhythm data will not be loaded into the ATELIER, and malfunctions could result. After returning the Rhythm stored in the User memory to the factory settings (p. 114), copy the Rhythm from USB memory once more.

If you want to delete the previously saved Rhythm and overwrite it with the Rhythm you’re newly saving, Press the [Rec] button.

If you don’t want to delete the previously saved Rhythm, press the [Reset] button, then select a number at which no Rhythm has been saved, and copy the Rhythm to that number.

You can return only the User memory to the factory settings. Refer to “Restoring the User Memory to the Original Factory Settings (User Memory Reset)” (p. 114).

To return to the basic screen, press the [Utility] button.

Copying Rhythms from User Memory to USB Memory

You can copy Rhythms from User memory to USB memory. To do so, press the [Media] button in step 7 (above) to choose “User.” In this

state, you’ll be copying Rhythms from User memory to USB memory.

The rest of the procedure is the same as when copying Rhythms from USB memory to User memory.

Deleting Saved Rhythm

You can delete Rhythms stored in User memory (p. 42) or USB memory.

Using the Rhythm Performance

fig.02-10.eps

Select the Rhythm you want to delete (p. 42).

Press the [Load] button and [Save] button simultaneously.

The following display appears.

To cancel the procedure, press the [Reset] button.

Press the [Rec] button.

While the Rhythm is being deleted, the following screen will be displayed.

Using the Rhythm Performance

NOTE

Never turn off the power while the operation is in progress. Doing so will damage the

TELIER’s internal memory or USB memory, making it unusable.

When deleting is complete, the basic screen reappears.

Using the Registration Buttons

The ATELIER allows you to store sound settings and panel settings such as 4 in the Registration buttons. There are a total of 4 Registration buttons, and one set of panel settings can be stored in each, allowing you to register a total of 4 different panel settings. Each set of panel settings that has been stored in a Registration button is called a “Registration.”

This provides a convenient way to change large numbers of panel settings during a performance, or to recall a complex panel setting.

fig.07-01

Write Manual

About the Registration Buttons

In addition to assigning voices and Rhythms to the Registration buttons, you can also store the following settings:

• Panel button settings (for example, settings for the Level [▲] and [▼] buttons, etc.)

• Controller settings (functions assigned to foot switches, etc.)

• Other types of settings (reverb type, tempo settings, degree of initial touch, etc.)

If you would like to know all of the settings that can be recorded to the Registration buttons, refer to “Settings That Are Stored In the Individual Registration Buttons” (p. 130).

The four settings stored at the Registration buttons can be saved as a “set” in USB memory, a floppy disk, or User memory (p. 61).

In addition to the settings saved to the Registration buttons, the following data is also saved when Registration sets are saved.

1 2 3 4

Settings that have been stored to Registration [1]–[4] buttons are remembered even if the power is turned off. If you wish to restore the settings stored in the Registration buttons to their factory settings, use the “Factory Reset” operation (p.

18).

Recorded performance data and Rhythms from User memory (p. 42) are not stored in Registration sets. When a Rhythm saved in User memory is assigned to a Registration set, that Rhythm is copied beforehand to the User memory.

• Registration Name → p. 59

• Registration Shift → p. 71

• Arranger Update → p. 58

• Trans. Update (Transpose Update) → p. 103

With the factory settings, the Arranger Update setting is set to “DELAYED.”

If Arranger Update is set to “DELAYED,” you will need to hold down the Registration button for several seconds in order to recall the tempo and Rhythm settings.

If you want the tempo and Rhythm settings to be recalled instantly when you press a Registration button, change the Arranger Update setting to “INSTANT.” For details, refer to “Recalling a Registration” (p. 58).

Procedure for Creating Registration Sets

Prepare the Registrations

A convenient way to make the sequence of Registration buttons to be pressed easy to understand is to store the panel settings starting from the Registration [1] button, continuing with subsequent buttons in accordance with the progression of the song.

Save the Registrations to the USB memory or User memory

If you want to use more than four Registrations in a song, save the settings for Registration buttons [1]–[4] to a USB memory or User memory as a set, then continue to store further panel settings again, starting from Registration button [1]. Save all of the Registration sets you have set to the USB memory or User memory.

Using the Registration Buttons

Arrange the Registrations in the sequence they are to be used

Save the Registration sets to the USB memory or User memory in the order they are to be used in the song.

Using Registration Sets

Call up the Registration sets saved on the USB memory to the ATELIER

Insert the USB memory containing the saved Registration sets into the External Memory connector, and read the Registration sets into the ATELIER.

Switch the Registration sets as you perform

Press the Registration buttons to switch Registrations as you play the song. If you want to recall the next Registration set, assign the foot switch to “RIGHT

+ Load Next” and recall the next Registration set (p. 71).

Storing Registrations

Make all the panel settings that you wish to store.

Using the Registration Buttons

While holding down the [Write] button, press one of the Registration [1]–[4] buttons.

The panel settings will be stored in the selected Registration button.

For details on the settings that are stored in a Registration, refer to “Settings That Are Stored In the Registration Buttons” (p. 130).

Using the Registration Buttons

Recalling a Registration

There are two ways of calling up the settings affecting the Rhythms registered to the Registration buttons [1]–[4], “INSTANT” and “DELAYED.” At the factory this is set to “DELAYED.”

How to Recall a Registration

Recalling Voices and Other Panel Settings

Press a Registration [1]–[4] button.

Recalling Settings for Rhythm and Automatic Accompaniment in Addition to the Panel Settings

Press and hold a Registration [1]–[4] button for several seconds.

The indicator of the Rhythm select button will blink, and the panel settings and settings related to Rhythm performance and Automatic Accompaniment will be recalled.

Changing the Timing of Recalling Registrations

Settings for Rhythm play and Automatic Accompaniment are recalled when you continue holding a Registration [1]–[4] button for several seconds, but you can change this so that the settings are recalled the instant you press the button.

fig.07-02

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select the “Arranger Update.”

Press the Value [-] [+] buttons to switch between “DELAYED” and “INSTANT.”

When you press and hold a Registration [1]–[4] button for several seconds, the settings for Rhythm and Automatic Accompaniment will be

DELAYED

INSTANT

To return to the basic screen, press the [Utility] button.

recalled in addition to the panel settings. If you press and immediately release a Registration [1]–[4] button, only the settings that are not related to Rhythm or Automatic Accompaniment will be recalled.

Settings for Rhythm and Automatic Accompaniment will be recalled the instant that you press a Registration [1]–[4] button.

You can change the timing of recalling the transpose setting when you press a Registration [1]–[4] button. For more information, please refer to “Registration Transpose Update (Trans. Update)” (p. 103).

Using the Registration Buttons

2,4

Automatically Registering When You Switch Panel Settings

When the [Manual] button is ON (lit), all panel settings you make will be stored automatically in the [Manual] button as they are made, thus updating the Registration that had been previously saved. If you change to a preset Registration [1]– [4] button, it is possible to return to the previous panel settings by pressing the [Manual] button.

fig.07-03

Write Manual

1 2 3 4

Assigning a Name to a Registration Set

When saving Registration sets, names like “Factory Reg.” will be assigned by default, but you can assign a name that will help you later to identify the contents of the Registration set.

fig.07-03

NOTE

The settings stored in the [Manual] button returns to the default settings while the power is turned off.

Using the Registration Buttons

2,4

Press the [Display/Exit] button a number of times to access the Registration screen.

Using the Registration Buttons

fig.07-05

Press the [Registration] button and [Media] button simultaneously.

Press the Menu [ ] [ ] buttons to move the cursor, and press the Value [-] [+] buttons to select a character.

The following characters can be selected when changing a name:

space ! " # % & ' ( ) * + , - . / : ; = ? ^ _ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9

[Reset] button

[Rec] button

Delete a character.

Inserts a space.

When you have finished assigning the name, simultaneously press [Registration] button and [Media] button once again.

The Registration set in the ATELIER’s internal memory has now been named.

To return to the basic screen, press the [Display/Exit] button.

Saving Registration Sets

With the settings of Registration buttons [1]–[4] considered as one set, you can store the Registration set to USB memory or User memory. We recommend that complex panel settings or Registrations you wish to keep be saved on USB memory.

Furthermore, when you save Registrations created on the ATELIER to USB memory, you can call up their settings on other ATELIER Series instruments and use the Registrations the same way.

Using the Registration Buttons

fig.07-10

Connect your USB memory to the External Memory connector.

Press the [Registration] button to make the indicator light.

The Registration Select screen appears.

Press the [Media] button to select the desired media.

If you want to save the Registration to USB memory, select “Ext Memory.” If you want to save the Registration to floppy disk, select “Disk.” If you want to save the Registration to User memory, select “User.”

Press the Value [-] [+] buttons to select the save-destination number.

Numbers which have not been used in the Saving operation will be displayed as “- - - - - - - - - - - -.”

If you want to save Registration data to a floppy disk, connect the floppy disk drive to the External Memory connector. Into the floppy disk drive, insert a floppy disk that was formatted by the ATELIER.

Using the Registration Buttons

To cancel the operation, press the [Registration] button.

Press the [Save] button.

Press the Value [-] [+] buttons to select the format in which the data will be saved.

Save formats that can be used with the AT-75.

ORIGINAL

R-SERIES

When saved in this format, the data can also be used by AT-S Series, AT-900, AT-900C AT-800, AT-500, AT-300, AT-100, AT-45 and AT-15 devices.

Save formats that can be used with AT-R Series devices

Using the Registration Buttons

fig.07-11

Press the [Save] button to execute the save operation.

Saving of the Registration data will begin.

When saving ends, the “- - - - - - - - - - - -” in the screen will change to the Registration name that you saved.

If you’ve named the Registration (p. 59), it will be saved with that name.

If the following screen appears

If you select a number at which a Registration has already been saved and press the [Save] button, the following screen appears.

NOTE

Never remove the USB memory or turn off the power while the operation is in progress. Doing so will damage the ATELIER’s internal memory or USB memory, making it unusable.

If you wish to update the contents of the Registration data

Press the [Rec] button.

The Registration will be rewritten.

If you wish to save new data instead of updating the Registration

Press the [Reset] button to cancel the procedure.

Rewriting of the Registration will be canceled.

Press the Value [-] [+] buttons to select a number for which “- - - - - - - - - - - -” is displayed on the upper right of the screen.

Press the [Save] button to save the Registration set.

When saving is complete, the saved Registration name will be displayed.

Using the Registration Buttons

Loading Previously Saved Registration Sets Into the ATELIER

Here’s how to recall a previously saved Registration set from the User memory or USB memory into the memory of the ATELIER. Registrations can be selected in the following two ways.

NOTE

Loading a Set of Registrations

You can load a “set” (a collection of settings for Registration buttons [1]–[4]) from Floppy disk, USB memory or User memory.

Loading an Individual Registration

Recall the settings of one of the Registration [1]–[4] buttons.

Be aware that when you load Registrations from a USB memory or User memory, the Registrations that were previously in internal memory

ill be lost. It is a good idea to save important Registrations to USB memory or User memory (p. 61).

Loading a Set of Registrations

If you want to load a Registration from USB memory, connect your USB memory to the External Memory connector.

Press the [Registration] button to make the indicator light.

The Registration Select screen appears.

Press the [Media] button to select the desired media.

If you want to load from the Registration of USB memory, select “Ext Memory.” If you want to load from the Registration of floppy disk, select “Disk.” If you want to load from the Registration of User memory, select “User.”

Press the Value [-] [+] buttons to select the Registration that you wish to load into internal memory.

Using the Registration Buttons

If you want to load a Registration from a floppy disk, connect the floppy disk drive to the External Memory connector, and insert the floppy disk containing the Registration into the floppy disk drive.

To cancel the procedure, press the [Registration] button.

Press the [Load] button to execute loading.

When loading is complete, the Registration Select screen reappears.

Since the ATELIER is designed

ith compatibility in mind, Registrations created on other instruments in the ATELIER series can be recalled. However, due to differences in the built-in sounds and functions, there will be cases in

hich the settings cannot be exactly replicated.

Using the Registration Buttons

Loading an Individual Registration

fig.07-14

If you want to load a Registration from USB memory, connect your USB memory to the External Memory connector.

Press the [Registration] button to make the indicator light.

The Registration Select screen appears.

Press the [Media] button to select the desired media.

If you want to load from the Registration of USB memory, select “Ext Memory.” If you want to load from the Registration of floppy disk, select “Disk.”

If you want to load from the Registration of User memory, select “User.”

Press the Value [-] [+] buttons to select the Registration that you wish to load into internal memory.

Press the [Utility] button.

Press the Value [-] [+] buttons to specify the Registration button number to be loaded.

fig.07-15

fig.07-16

To cancel the operation, press the [Utility] button.

Press the [Rec] button.

Press the Value [-] [+] buttons to specify the storagedestination Registration.

Press the [Rec] button.

The following display appears.

To cancel the procedure, press the [Reset] button.

10.

Press the [Rec] button once again.

When the Registration has been loaded, the Registration Load screen will reappear.

Deleting a Set of Registrations

Here’s how to delete a Registration set that was saved to a USB memory, User memory (p. 42), or floppy disk.

Using the Registration Buttons

fig.07-08

Prepare the Registration that you want to delete.

If you want to delete Registration data from the USB memory, connect the USB memory to the External Memory connector.

Press the [Registration] button to make the indicator light.

The Registration Select screen appears.

Press the [Media] button to select the desired media.

If you want to delete from the Registration to USB memory, select “Ext Memory.”

If you want to delete from the Registration to floppy disk, select “Disk.” If you want to delete from the Registration to User memory, select “User.”

Press the Value [-] [+] buttons to select the Registration that you wish to delete.

Simultaneously press the [Load] button and [Save] button.

The following display appears.

If you want to delete Registration data from the floppy disk, connect the floppy disk drive to the External Memory connector. Into the floppy disk drive, insert a floppy disk.

Using the Registration Buttons

fig.07-18

To cancel the procedure, press the [Reset] button.

If you are sure that you wish to delete the data, press the [Rec] button.

When a Registration is deleted, the deleted Registration name will change to “- - - - - - - - - - - -.”

NOTE

Never remove the USB memory or turn off the power while the operation is in progress. Doing so will damage the ATELIER’s internal memory or USB memory, making it unusable.

Using the Registration Buttons

Copying Registrations

Registrations from USB memory or floppy disk can be copied to User memory. If a Registration saved in USB memory or on a floppy disk is stored in User

memory, the stored Registration data will not disappear even when you turn off the power. It is convenient to load frequently-used Registration into User memory.

Registrations saved in User memory can also be copied to USB memory (p.

67).

Copying Registration from USB Memory to User Memory

fig.02-09.eps

fig.02-10.eps

Connect the USB memory to the External Memory connector.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Media Utility.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Copy Registration.”

If you want to copy Registration from floppy disk, connect the floppy disk drive to the External Memory connector.

Press the [Rec] button.

Press the [Media] button to select the media (the location of the Registration you want to copy).

If you want to copy a Registration from USB memory, select “Ext Memory.” If you want to copy a Registration from floppy disk, select “Disk.”

Using the Registration Buttons

10.

11.

Press the Value [-] [+] buttons to select the Registration you want to copy.

Press the [Rec] button.

Press the Value [-] [+] buttons to select the copy-destination number.

To cancel the procedure, press the [Display/Exit] button.

Press the [Rec] button to copy the Registration.

If you select a number in which a Registration is already saved, a screen like the following appears.

NOTE

Never remove the USB memory or turn off the power while the Registration data is being copied from USB memory into the ATELIER. If you do so, the Registration data will not be loaded into the ATELIER, and malfunctions could result. After returning the Registration stored in the User memory to the factory settings (p. 114), reload the Registration from USB memory.

Using the Registration Buttons

If you want to delete the previously saved Registration and overwrite it with the Registration you’re newly saving, Press the [Rec] button.

If you don’t want to delete the previously saved Registration, press the [Reset] Button, then select a number at which no Registration has been saved, and copy the Registration to that number.

To return to the basic screen, press the [Utility] button.

Copying Registration from User Memory to USB Memory

You can copy Registration from User memory to USB memory. To do so, press the [Media] button in step 7 to choose “User.” In this state,

you’ll be copying Registration from User memory to USB memory.

The rest of the procedure is the same as when copying Registration from USB memory to User memory.

You can return only the User memory to the factory settings. Refer to “Restoring the User Memory to the Original Factory Settings (User Memory Reset)”(p. 114).

Using the Performance Functions



Transposing to a Different Key (Key Transpose)

You can transpose the key of a performance without having to shift the position of your fingers on the keyboard. This feature is called “Key Transpose.”

For example: you may play in the familiar C major scale while your music will sound in any key of your choice.

fig.06-01

fig.06-03

Press the Transpose [-] [+] buttons.

Each press of the Transpose [-] or [+] button transposes the key a semitone.

The transpose value is displayed in the screen.

Acceptable values range from A to G (in semitone steps).

If the pitch is transposed (something other than C), the indicator of one of the Transpose buttons, either [-] [+], will be lit. If the pitch is not transposed (i.e., the key is C), the indicator of both the Transpose [-] and [+] buttons will be extinguished.

By pressing the Transpose [-] and [+] buttons simultaneously,

ou can restore the default

setting “C.”

You can change the timing at which the transposition settings saved in a Registration will be recalled. For details refer to “Registration Transpose Update (Trans. Update)” (p. 103).

Using the Foot Switch

On each side of the expression pedal are two Foot Switches. Different functions are assigned to each of these two foot switches.

fig.06-07

With the factory settings, the following functions are assigned to the left and right Foot Switches.

Using the Performance Functions

You can also change the function assigned to the Foot Switch. Please refer to “Changing the Function of the Foot Switch” (p.

70).

Right Foot Switch

Left Foot Switch

Switch the Rotary effect between Fast/Slow.

Glide (an effect by which the pitch is lowered by a semitone while the foot switch is pressed, and is returned to what is originally was when you release your foot).

Press the right Foot Switch toward the right.

If Rotary is turned on, the Rotary effect will switch between “Fast” and “Slow” each time you press the Right Foot Switch.

Press the left Foot Switch toward the left.

While you are pressing the Foot Switch, the pitch will be temporarily lowered. When you release the Left Foot Switch, the pitch will return to normal.

Using the Performance Functions

NOTE

The Glide effect is applied only to the upper part. However, it won’t be applied to the Vintage Organ in the upper part.

You can store functions to be assigned to the foot switch to individual Registration buttons (p. 70).

Using the Performance Functions

NOTE

Changing the Function of the Foot Switch

You can select any of the following functions and assign them to either Foot Switch on the right or left side of the Expression Pedal.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “L Foot Switch” or “R Foot Switch.”

ig.12-09

Setting

COMP PLAY/STOP

INTRO/ENDING

VARIATION UP

VARIATION DOWN

VARIATION ALT.

FILL IN

Description

The same function as the Composer [Play/Stop] button. Each time you press the Foot Switch, the performance data will play back or stop.

Play an Intro or Ending.

Switches the Variation buttons. Each time you press the foot switch, the Variation number will increment.

Switches the Variation buttons. Each time you press the foot switch, the Variation number will decrement.

Switches the Variation button. If the Variation [1] button or [3] button is selected, this will switch between the Variation [1] and [3] buttons. If the Variation [2] button or [4] button is selected, this will switch between the Variation [2] and [4] buttons.

Adds a fill-in.

Press the Value [-] [+] buttons to set the

function to be assigned to the foot switch.

To return to the basic screen, press the [Utility] button.

Setting

ROTARY FAST/ SLOW

GLIDE

Switch the Rotary speed between “FAST” and “SLOW.”

While the Foot Switch is pressed, the pitch will temporarily be lowered, and will gradually return to normal when you release the Foot Switch. Glide effect is added to the voice of all the sections being played on Upper keyboard.

NOTE

Description

The Glide effect is applied only to the upper part. However, it won’t be applied to the Vintage Organ in the upper part.

BREAK

DAMPER OF UPPER

DAMPER OF LOWER

OFF

If the Utility menu “Registration Shift” setting is “RIGHT”, “LEFT” or “RIGHT+LoadNext“, the Foot Switch will be dedicated to switching through the Registrations, and the “R Foot Switch” or “L Foot Switch” setting will be ignored.

Stop the Rhythm for one measure (break).

Notes played on the Upper keyboard will be sustained only while you continue pressing the Foot Switch.

Decay cannot be added to

NOTE

the Solo voices.

Notes played on the Lower keyboard will be sustained only while you continue pressing the Foot Switch.

Turns the foot switch function off.

LEADING BASS

RHYTHM START/ STOP

The Leading Bass function (p. 50) will operate only while you continue pressing the Foot Switch.

Start/Stop the Rhythm.

Using the Performance Functions

Using the Foot Switch to Switch Registrations (Registration Shift)

You can use the Foot Switch as a dedicated switch for selecting Registrations in order. The Registration will be switched each time you press the foot switch.

The Registration Shift settings are stored to each individual Registration Set. When “RIGHT + Load Next” is assigned to the foot

NOTE

switch and the Load Next function is used to switch Registration Sets saved to a USB memory or floppy disk, set the Registration Shift setting to “RIGHT + Load Next” for all saved Registrations.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number

of times to select “Registration Shift.”

Setting

The right foot switch is dedicated to switching Registrations. The function assigned to the right foot switch cannot be used. Selecting the Registration [4] button and pressing the right foot switch activates the Load Next function, calling up the next

RIGHT + Load Next

What is “Load Next”?

You can use the Load Next function to call up Registrations in the order saved to the USB memory, User memory, or floppy disk. When you will be performing live, you can save Registration sets to USB memory, User memory, or floppy disk in the order in which you will be performing. Then while you perform, you can recall the next Registration set easily and smoothly.

Registration saved to the USB memory, User memory, or floppy disk. The Registration Load window appears in the display. When you then press the right foot switch again, the Registration Set is confirmed, and the Registration [1] button is selected. Example: 1→2→3→4 →Load Next (Next Registration) 1

Description

→

Using the Performance Functions

Press the Value [-] [+] buttons to change the setting (OFF/RIGHT/LEFT/RIGHT + Load Next).

Setting

OFF

RIGHT

LEFT

You can use a function assigned to the foot switch.

The right foot switch is dedicated to switching Registrations. The function assigned to the right foot switch cannot be used.

The left foot switch is dedicated to switching Registrations. The function assigned to the left foot switch cannot be used.

Description

To return to the basic screen, press the [Utility] button.

This setting remains stored in memory even while the power is turned off.

Using the Performance Functions

Adjusting the Overall Volume Using an Expression Pedal

You can adjust the entire volume using an Expression Pedal. When you depress the Expression Pedal, the volume increases. The volume decreases as you tilt the pedal back.

Likewise you can specify

fig.06-03

Decrease the volume

Increase the volume

Using the expression pedal enables you to give your performances even richer musical expressiveness.

The expression pedal features the following special characteristics:

• Completely releasing the expression pedal does not lower the volume to zero. If you do want to turn down the volume completely, set the [Master Volume] knob to the Min (Minimum) position.

• Even as you release your foot from the expression pedal and lower the volume, the lower-range portion will linger on. This provides a naturalsounding resonance.

whether the Expression Pedal will or will not control the volume during the playback of recorded music data (p. 100).

You can specify whether the expression pedal will function when playing back performance data that was recorded on the ATELIER series (p. 101).

• When an Active Expression voice is selected, the expression pedal can be used to produce changes in the voice (p. 33).

Adding Various Effects to a Voice

The ATELIER allows you to apply various effects to the sounds you play from the keyboard.

Adding Harmony to a Melody (Harmony Intelligence)

Harmony appropriate for the chord you play in the lower keyboard can be added to the highest note played in the upper keyboard. This function is called “Harmony Intelligence.”

When you press the [Harmony Intelligence] button, the voice most suitable for the selected harmony intelligence will be selected automatically.

fig.04-01

Press the [Harmony Intelligence] button (indicator lights).

Each time you press a [Harmony Intelligence] button, the indicator will alternate between ON (lit) and OFF.

Adding Various Effects to a Voice

Changing the Type of Harmony Intelligence

The AT-75 provides six types of harmony intelligence.

When you press the [Harmony Intelligence] button, the most appropriate voice(s) will be automatically set.

The manner in which notes will sound also depends on the Harmony type.

Press the [Harmony Intelligence] button (indicator lights).

While the Harmony Intelligence name is shown in the display screen, use the Value [-] [+] buttons to select the Harmony Intelligence.

The indicator of the [Harmony Intelligence] button will blink.

To cancel the procedure, press the [Display/Exit] button.

Once again, press the [Harmony Intelligence] button.

The indicator of the [Harmony Intelligence] button will light, and the Harmony Intelligence is confirmed.

Harmony Intelligence types:

Type

BIG BAND

STRINGS

TRADITIONAL*

OCTAVE 1*

BIG BAND*

STRINGS*

Solo Voice Upper Voice

Trumpet

Strings 1

Currently Selected Tone

Flugel Horn 5

Strings 5 4

Number of notes of the

harmony

You can also play the upper manual to confirm the type of the Harmony Intelligence.

The number of notes of the harmony will depend on the Harmony Intelligence type.

Harmonies are added only to the Upper voice.

Adding Various Effects to a Voice

Adding Modulation to the Sound (Rotary Effect)

Rotary is an effect which simulates the sound of rotating speakers. There is a choice of two settings: Fast and Slow.

fig.05-06.eps

Select the voice to which you wish to apply the Rotary effect.

Press the Rotary Sound [On/Off] button (confirm that its

NOTE

For more on the tones to which the Rotary effect can be applied, refer to “Voice & Rhythm List” (Appendix: separate booklet).

indicator is lit).

The Rotary effect will be applied to the voice.

Press the Rotary Sound [Fast/Slow] button to switch between Rotary Fast (Lit) and Rotary Slow (Unlit).

Rotary Sound

[Fast/Slow] button

Lit (Fast)

Unlit (Slow)

When you switch the rotary effect from “Fast” to “Slow,” the modulation will slow down gradually, and when you switch from “Slow” to “Fast” the modulation will speed up gradually.

The effect obtained is equivalent to speakers being rapidly rotated.

Effect simulating the slow rotation of speakers.

Effect

Adding Various Effects to a Voice

You can assign the Rotary Sound [Fast/Slow] button function to the foot switches located on each side of the Expression Pedal (p. 70).

Adding Various Effects to a Voice

Sustain Effect

Sustain allows you to add a Sustain effect or decay to each voice after the keys are released. The Sustain effect can be added simultaneously to the Upper (except the Solo Part), Lower, and Pedal Bass voices.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select the “Sustain.”

NOTE

The Sustain effect will not be applied to the Solo part and vintage organ part voice.

Press the [Rec] button.

Press the Menu [ ] [ ] buttons to select the desire part.

Part

Upper, Lower, Pedal

Press the Value [-] [+] buttons to switch “ON” or “OFF.”

To return to the basic screen, press the [Utility] button.

The length of Sustain can be modified independently for each keyboard (p. 77).

Changing the Sustain Length

The sustain length can be set independently (SHORT, MIDDLE (Medium) or LONG) for the Upper and Lower keyboards and Bass Pedalboard. You can make a separate setting for each keyboard.

Adding Various Effects to a Voice

fig.11-06

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Sustain.”

Press the [Rec] button.

Adding Various Effects to a Voice

Press the Menu [ ] [ ] buttons a number of times to select “Length.”

Press the Menu [ ] [ ] buttons to select the part whose sustain length you wish to adjust.

Part

Upper, Lower, Pedal

Press the Value [-] [+] buttons to adjust the setting.

Settings

SHORT, MIDDLE, LONG

To return to the basic screen, press the [Utility] button.

Adding Various Effects to a Voice

Reverb Effect

Reverb is an effect that adds a sense of spaciousness to the sound, creating the illusion of playing in a large or small concert hall, a large or small room, a small club, etc.

fig.04-07

Press the Reverb [▲] or [▼] button to adjust the overall Reverb amount.

When you press the Reverb [▲] button, additional Reverb is applied. Pressing the Reverb [▼] button decreases the Reverb level.

When you press the Reverb [▲] [▼] buttons, the Reverb level will be shown in the display.

Changing the Reverb Type

By changing the reverberations of the notes, you can enjoy the atmosphere of performance in a wide variety of different locations.

Adding Various Effects to a Voice

fig.11-04

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Reverb.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons to a number of times select “Reverb Type.”

Adding Various Effects to a Voice

Press the Value [-] [+] buttons to select a Reverb type.

Type

ROOM 1

ROOM 2

ROOM 3

HALL 1

HALL 2

SMALL CHURCH

LARGE CHURCH

CATHEDRAL

PLATE

DELAY

PAN DELAY

To return to the basic screen, press the [Utility] button.

Reverberation of a small room

Reverberation of a small club

Reverberation of a large room

Reverberation of a large concert hall

Reverberation of a small concert hall

The reverberation of a small church

The reverberation of a large church

The reverberation of a cathedral

A bright, metallic Reverberation

An echo-like sound repeated several times

Similarly to the above but where the sound is panned between the left and right speakers

Description

Adding Various Effects to a Voice

Changing the Wall Type

By changing the type of reverb you can experience the feeling of performing in various different locations, and by changing the Wall Type (wall material) you can make further adjustments to the way in which reverberation occurs.

fig.11-04

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Reverb.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Wall Type.”

Press the Value [-] [+] buttons to select a Wall type.

Type

DRAPERY

CARPET

ACOUSTIC TILE

WOOD

BRICK

PLASTER

CONCRETE BLOCK

MARBLE

To return to the basic screen, press the [Utility] button.

Pleated curtain

Carpet

Acoustical tile, sound-absorptive tile

Wood

Brick

Plaster

Concrete block

Marble

Description

Changing the Depth of the Reverb

You can make independent settings for each Part.

Adding Various Effects to a Voice

fig.11-05

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Reverb.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Depth.”

Adding Various Effects to a Voice

Press the Menu [ ] [ ] buttons to select the part whose reverb depth you wish to adjust.

Part

Accomp A.Bass

(Automatic Accompaniment except Bass)

(Bass part of Automatic Accompaniment)

, Rhythm, Drums,

, Pedal, Lower, Solo, Vintage

Press the Value [-] [+] buttons to adjust the setting.

Settings Description

0–10 AUTO (Accomp, Rhythm, A.Bass)

For the three Parts of the Accomp, Rhythm and A.Bass, you have the option of selecting the “AUTO” setting. Parts for which “AUTO” is selected will be set to the Reverb Depth that is most suitable for the Rhythm currently selected.

To return to the basic screen, press the [Utility] button.

Increasing the value will increase the amount of reverb effect.

Record and Playback Your Performance

The internal composer can record performances and play back commercial SMF music files.

fig.08-01

What is a Track Button?

The recorded performance will be automatically assigned to the three Track buttons according to the recorded part. You can record or play back independently by specifying the desired Track button; for example, when you wish to re-record a track.

You can record different kinds of performance data into each track:

Button

Song

Registration

Media

Description

The Song Select screen appears in the display.

The Registration Select screen appears in the display.

Switches the media.

Button Recorded Performance

Bass

Lower

Solo /Upper

Button

Reset

Play/Stop

Rec

Pedal Bass Voice Performance Data (Note)

Bass part of the Automatic Accompaniment

Lower Voice Performance Data (Note, Hold)

Upper Voice Performance Data (Note, Hold)

Solo Voice Performance Data (Note)

Description

Returns you to the beginning of the song.

Starts and stops playback of the song.

After the [Rec] button has been pressed, putting the composer in record standby mode, recording then starts when the [Play/ Stop] button is pressed.

The ATELIER switches to record standby mode. * In record standby, the [Rec] button is lit,

and the [Play/Stop] button flashes.

Bwd

Fwd

Rewinds the song.

Fast forwards the song.

More information about the track assignments when playing commercial SMF music files, please refer to “Silencing a Specific Track (Track Mute)” (p. 106).

If you wish to erase all the recorded data and record new performance data, use the editing function “Erase” (erase performance data) to erase the data (p. 87).

Playing Back Performance Songs Stored on USB Memory and SMF Music Files

In addition to playing back the music you recorded on the instrument and saved to a USB memory, ATELIER also lets you enjoy a wide variety of commercially available song files, such as defined below.

SMF Music Files

SMF (Standard MIDI File) is a data format that was created in order to standardize music data formats between manufacturers. Collections of songs in SMF music data are commercially available in a wide range of styles for enjoyment, as accompaniment for practicing musical instruments, and for karaoke.

If you want to purchase SMF music data, you can contact the dealer where you purchased the ATELIER.

Record and Playback Your Performance

To Play Back Only One Song

Prepare the song that you want to play back.

If you want to play a song from USB memory, connect it to the External Memory connector.

If you want to play a song from floppy disk, connect the floppy disk drive to the External Memory connector, and insert a floppy disk into the drive.

Press the [Song] button (confirm that its indicator is lit).

The Song Select screen appears.

Press the [Media] buttons to select the desired media.

If you want to play a song from USB memory, choose “Ext Memory.” If you want to play a song from floppy disk, choose “Disk.”

5, 6

Press the Value [-] [+] buttons to select the

song that you wish to play back.

Press the [Play/Stop] button to start playback.

Playback of the performance data begins.

To stop playback, press the [Play/Stop]

button.

Playing Back All Performance Data

Prepare the song that you want to play back.

If you want to play a song from USB memory, connect it to the External Memory connector.

If you want to play a song from floppy disk, connect the floppy disk drive to the External Memory connector, and insert a floppy disk into the drive.

While holding down the [Song] button, press the [Play/Stop] button.

All performance data saved on the USB memory or floppy disk will be played consecutively.

Record and Playback Your Performance

To stop playback, press the [Play/Stop] button.

Record and Playback Your Performance

Silencing a Specific Track (Track Mute)

The indicators for Track button in which performances were recorded will be lit. By turning off these Track button indicators, you can temporarily silence the sound. This is referred to as “Track Mute.”

If you want to play back a song from USB memory, connect your USB memory to the External Memory connector before you continue.

If you want to play back a song from floppy disk, connect your floppy disk drive to the External Memory connector, and insert the floppy disk.

Recording a Performance

You can record the performance that you play. You can also record your performance while playing Rhythms or Automatic Accompaniment.

fig.07-12.eps

23, 4

Select the panel settings needed for recording the performance.

Enter the recording standby mode by pressing

the [Rec] button.

The [Rec] button indicator will light, and the [Play/Stop] button will blink.

Press the Track buttons whose indicator is lit to

turn the light off.

The track whose indicator was turned off will be muted (silenced).

Press the Track buttons once again (indicator

lights).

The part that had been muted will return to normal and will be heard.

Assignments to the Track Buttons When Playing Back Commercial SMF Music Files

Button

[Bass]

[Lower]

[Solo/Upper]

You can also change the Track Mute Settings in the Utility menu (p. 106). You can individually mute the Rhythm track and accompaniment track as well as the Upper Track and Solo Track. You can also mute the Control Track (for the expression pedal and panel controls) (p. 106).

1, 4

Channel

Press the [Play/Stop] button to start recording.

When you press the [Play/Stop] button, the metronome will sound a two-measure count, and then recording will begin.

If you wish to use Rhythm and Automatic Accompaniment as you record, press the [Start/Stop] button (p. 43) instead of the [Play/Stop] button to begin recording. Also, if the Sync Start is ON, recording will begin the instant you play the Lower keyboard.

Press the [Play/Stop] button when you have

completed your recording.

The Track indicator where a performance song is recorded will light.

When you press the [Intro/Ending] button or [Start/Stop] button while recording a Rhythm performance or Automatic Accompaniment, the Rhythm performance and Automatic Accompaniment will stop. However, the recording itself will continue. Press the [Play/Stop] button to stop recording.

The Play and Stop functions can both be assigned to one of the foot switches located on each side of the Expression Pedal (p. 70).

Caution

NOTE

If you press the [Rec] button when a song has been selected from the USB memory or floppy disk, the selected song will be completely loaded into the ATELIER and the Composer will enter into the recording standby mode. To record a new song, use the following procedure.

ig.07-12-2.eps

Press the [Rec] button to cancel recording standby.

Disconnect the external media.

If you’ve connected USB memory, disconnect the USB memory from the External Memory connector. If you’re using a floppy disk, remove the floppy disk from the floppy disk drive.

Delete the performance data (p. 87).

Re-record your performance.

If the following screen appears

fig.E-30.eps

Record and Playback Your Performance

Playing Back a Performance Song

Here’s how to play back a performance you’ve recorded.

fig.08-06

1 2, 3

Press the [Reset] button.

The location at which playback will start will return to the beginning of the first measure (bar).

If you wish to begin playback from the middle of the song, press the [Bwd] button or [Fwd] button to move to

the measure from which you wish to begin playback.

Press the [Play/Stop] button to start playback.

After playback reaches the end of the performance, it will stop automatically.

To stop playback at any point, press the [Play/

Stop] button.

The [Play/Stop] function can be assigned to the foot switch (p. 70).

You can specify whether or not the Expression Pedal will affect the playback and what you play while ATELIER music data is being played back (p. 100).

Record and Playback Your Performance

When recording was automatically canceled because the memory limit was reached.

If you use the Rhythm or Automatic Accompaniment immediately after having loaded and played back a song other than an ATELIER performance song, such as SMF’s, etc., the playback may not sound right (the voices may have changed, etc.). To prevent this from happening, press the [Reset] button before playback.

Record and Playback Your Performance

NOTE

Add a Count Sound to Match the Timing (Count In)

In cases such as when you want to perform in time with a song, you can have a count sound played before playback of the song begins, allowing you to synchronize your own performance with the song.

Playing back a song after playing the count sound is called “Count In.”

Hold down the [Reset] button and press the [Play/Stop] button.

The metronome will play two measures (bars) of count-in before recording begins.

Recording Each Part Separately

In this method, each part (track buttons) is recorded one after another: first the bass part, then the Lower part, etc. If there are any previously recorded performances, you can listen to them as you record additional parts.

25, 6

Select the panel settings needed for recording

the performance.

Press the [Bwd] button or the [Fwd] button to

select the desired measure (bar) when you start recording.

If you wish to start recording from the beginning of the song, press the [Reset] button.

Press the [Rec] button to enter recording-

standby mode.

The [Rec] button indicator will light, and the [Play/Stop] button and the unrecorded track buttons will blink. The track buttons that are already recorded will light.

Press the button of the track you want to record, so it’s blinking.

The existing performance data in the specified track will be erased as recording takes place.

When the button for a track lights steadily, it means it won’t be recorded.

Press the [Play/Stop] button to start recording.

When you press the [Play/Stop] button, the metronome will sound a two-measure count, and then recording will begin.

As you listen to the performance song previously recorded, record the Part into a new Track.

Press the [Play/Stop] button to stop recording.

The track button for which performance data has been recorded will be lit.

Repeat steps 2–6 to record each part.

Record and Playback Your Performance

Re-Recording

You can record over recorded performance data.

14, 532

Press the [Bwd] button or the [Fwd] button to select the desired measure (bar) when you start recording.

If you wish to start recording from the beginning of the song, press the [Reset] button.

Press the [Rec] button to enter recording-

standby mode.

The [Rec] button indicator will light, and the [Play/Stop] button and the unrecorded track buttons will blink. The track buttons that are already recorded will light.

Press the button of the track you want to

record, so it’s blinking.

The existing performance data in the specified track will be erased as recording takes place.

When the button for a track lights steadily, it means it won’t

NOTE

be recorded.

Erasing a Performance Song

If you wish to discard your recording and re-record from the beginning, or if you wish to record a new performance, you must erase the previously-recorded data.

Press the [Display/Exit] button a number of times to access the Composer screen.

Record and Playback Your Performance

Press the [Play/Stop] button to start recording.

When you press the [Play/Stop] button, the metronome will sound a two-measure count, and then recording will begin.

As you listen to the performance song previously recorded, record the Part into a new Track.

Press the [Play/Stop] button to stop recording.

The track button for which performance data has been recorded will be lit.

If you wish to re-record with different settings for voices,

NOTE

tempo, part balance, erase the recorded song (p. 87) and re-record again. If the Control track still contains data from before you re-recorded, the volume or sounds may change during playback.

If you wish to keep the existing Expression Pedal data, and record only the panel operations, you can make settings to prevent the operation of the Expression Pedal from being recorded (p. 100).

Press the [Load] and [Save] buttons simultaneously.

The following message, asking you to confirm your choice, will be displayed.

fig.08-10

To cancel the procedure, press the [Reset] button.

If you are sure that you wish to erase the song, press the [Rec] button.

Record and Playback Your Performance

NOTE

Changing the Name of a Performance Song (Rename)

A name is automatically assigned to a performance song that you record. However, at some point you may wish to change the name to something more meaningful.

Press the Menu [ ] [ ] buttons to move the

cursor, and press the Value [-] [+] buttons to select a character.

The following characters can be selected when changing a name:

space ! " # % & ' ( ) * + , - . / : ; = ? ^ _ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z a b c d e f g h i j k l m n o p q r s t u v w x y z 0 1 2 3 4 5 6 7 8 9

Press the [Reset] button.

Delete a character.

2,4

Press the [Display/Exit] button a number of times to access the Composer screen.

Press the [Rec] button.

To confirm the new name, simultaneously

Insert a space.

press the [Registration] and [Media] buttons once again.

The new name is now inserted.

You cannot directly change or edit the name of a performance song stored on a USB memory, floppy disk or

“Favorites” (internal memory

loaded (p. 90) into the instrument, edited, and then saved to USB memory or floppy disk again.

). The song must first be

Press the [Registration] and [Media] buttons simultaneously.

fig.08-10

Saving Performance Songs

NOTE

NOTE NOTE

The performance data that you recorded will disappear when the power of the ATELIER is turned off. If you wish to keep the performance data, you can save it on a USB memory, floppy disk, or “Favorites” (internal memory).

If the recorded performance data has not been saved, the display will show the “ ” symbol. This symbol will

disappear when you save the performance data.

fig.08-20

Record and Playback Your Performance

Press the [Media] button to select the media.

Select “Ext Memory” to save the data in USB memory, select “Disk” to save it on a floppy disk, or “Favorites” to save it in User memory.

Press the Value [-] [+] buttons to select the number of the save destination.

If the save destination contains no data, the screen will indicate “- - - - - - - - - - - - .”

fig.07-28-2.eps

fig.08-19

4,6

Prepare to save the performance song.

If you want to save performance song to a USB memory, connect the USB memory to the External Memory connector.

If you want to save performance song to a floppy disk, connect the floppy disk drive to the External Memory connector. Into the floppy disk drive, insert a floppy disk that was formatted by the ATELIER.

5,7

Press the [Save] button.

Press the Value [-] [+] buttons to select the format.

You can select either “ORIGINAL” or “SMF” format.

Display

ORIGINAL

SMF

SMF (Standard MIDI File) is a data format that was created as a standardized way to exchange music data between devices made by different manufacturers.

Press the [Save] button to confirm the format.

Saving of the performance data will begin.

Save data in ATELIER format

Saving in SMF Format for ATELIER Sound Modules

Description

Record and Playback Your Performance

Press the [Song] button (confirm that its

indicator is lit).

The Song Select screen appears.

Never turn off the power while the operation is in progress. Doing so will damage the ATELIER’s internal memory or USB memory, making it unusable.

Performance data saved by the ATELIER format cannot be played back properly by the sound generator of an instrument that is not a member of the ATELIER series.

Saving performance data in SMF format (SMF) requires a longer time than saving it in ATELIER format (Original).

Record and Playback Your Performance

If the following screen appears

If you select a number at which a performance data has already been saved, the following screen appears.

fig.E-64-b.eps

If you wish to update the contents of the performance data

Press the [Rec] button.

If you want to save your performance as new data without overwriting the existing data

Loading Performance Songs Into the ATELIER

To re-record a performance song that is stored on a USB memory or floppy disk, you must first load that song into the instrument.

2 3

Press the [Reset] button to stop the Save operation.

In the Song Select screen, select the number

that is displayed as “------------” (a number that currently does not contain performance data).

Save the performance data.

When saving is complete, the saved performance name will be displayed.

Prepare the performance song.

If you want to load performance song to a USB memory, connect the USB memory to the External Memory connector. If you want to load performance song to a floppy disk, connect the floppy disk drive to the External Memory connector. Into the floppy disk drive, insert a floppy disk that was formatted by the ATELIER.

Press the [Song] button (confirm that its

indicator is lit).

The Song Select screen appears.

Press the [Media] button to select the media.

If you want to load a song from USB memory, choose “Ext Memory.” If you want to load a song from floppy disk, choose “Disk.”

Press the Value [-] [+] buttons to select the

performance song that you wish to load into internal memory.

Press the [Load] button.

The selected performance data will be loaded into internal memory.

If loading is canceled because the memory limit has been reached, the following message will be displayed:

fig.E-30.eps

Record and Playback Your Performance

Deleting Performance Songs Stored on “Favorites” or the USB Memory

You can delete a performance song that was saved onto a “Favorites,” USB memory, or floppy disk.

If you want to delete a song in USB memory, connect your USB memory to the External Memory connector before you continue.

If you want to delete a song in floppy disk, connect the floppy disk drive to the External Memory connector, and insert a floppy disk into the drive.

If the following screen appears

If the performance song in the ATELIER has not been saved to a USB memory or Favorites (User memory), the following message appears.

fig.E-62.eps

If you wish to erase the performance song

Press the [Rec] button.

If you don’t wish to erase the performance song

Press the [Song] button (confirm that its

indicator is lit).

The Song Select Screen appears.

Record and Playback Your Performance

Press the [Reset] button to stop the Save

operation.

Save the song to USB memory or a floppy disk (p. 89).

Press the [Media] button to select the media.

If you want to delete a song from the “Favorites,” choose “Favorites.”

If you want to delete a song from USB memory, choose “Ext Memory.” If you want to delete a song from floppy disk, choose “Disk.”

Press the Value [-] [+] buttons to select the

performance data that you wish to delete.

Record and Playback Your Performance

Press the [Load] button and [Save] button

simultaneously.

The following message, asking you to confirm your choice, will be displayed.

fig.08-10

To cancel the procedure, press the [Reset] button, and you will return to the Song Select screen.

If you are sure that you wish to delete the song, press the [Rec] button.

Never turn off the power while the operation is in progress. Doing so will damage the ATELIER’s internal memory or USB

NOTE

memory, making it unusable.

Layering a New Recording onto SMF Music Files

You can load commercially available SMF music files into the ATELIER, and record your own performance on top of it. During recording, the data you’ve loaded will be played back, while you record your performance.

2 3

10,11

Prepare the SMF music files.

If you’re using SMF music files from USB memory, connect it to the External Memory connector.

If you’re using SMF music files from a floppy disk, connect the floppy disk drive to the External Memory connector, and insert the floppy disk.

Press the [Song] button (confirm that its

indicator is lit).

The Song Select screen appears.

Press the [Media] button to select the media.

If you want to play SMF music files from USB memory, choose “Ext Memory.” If you want to play SMF music files from floppy disk, choose “Disk.”

Press the Value [-] [+] buttons to select the SMF

3643

music files that you wish to load into internal memory.

Press the [Load] button.

The selected performance data will be loaded into internal memory.

Press the [Bwd] button or the [Fwd] button to

select the desired measure (bar) when you start recording.

If you wish to start recording from the beginning of the song, press the [Reset] button.

Select the panel settings needed for recording

the performance.

Press the [Rec] button to enter recordingstandby mode.

The [Rec] button indicator will light, and the [Play/Stop] button and the unrecorded track buttons will blink. The track buttons that are already recorded will light.

Press the button of the track you want to

record, so it’s blinking.

The existing performance data in the specified track will be erased as recording takes place.

When the button for a track lights steadily, it means it won’t

NOTE

be recorded.

Record and Playback Your Performance

Using Song with a Different Tempo Than That of the Performance Song

Prepare the performance data whose tempo

you want to change.

If you’re using performance data from USB memory, connect it to the External Memory connector.

If you’re using performance data from a floppy disk, connect the floppy disk drive to the External Memory connector, and insert the floppy disk.

Record and Playback Your Performance

10.

Press the [Play/Stop] button to start recording.

During recording, the performance data that was loaded into the ATELIER will play back.

Press [Stop] button to stop recording.

11.

The track button for which performance data has been recorded will be lit.

The performance data you recorded can be saved on a USB memory, “Favorites,” or floppy disk (p. 89).

Commercially sold music files can also be loaded into the ATELIER, but for reasons of copyright protection, cannot be

NOTE

saved in SMF format.

The performances of Channel 2 in SMF music files are

NOTE

deleted when pedal performances are recorded over again.

Load the performance data into the ATELIER

(p. 90)

Determine the tempo with the Tempo [ ] [ ]

buttons.

Hold down the panel [Reset] button and press

the [Rec] button.

The tempo of the performance data will change.

Record and Playback Your Performance

NOTE

Copying Performance Song

Performance songs and SMF music files from USB memory or floppy disk can be copied to “Favorites” (User memory).

If a performance song saved in USB memory or on a floppy disk is stored in “Favorites,” the stored performance song will not disappear even when you turn off the power. It is convenient to load frequently-used performance song into “Favorites.”

Performance songs saved in “Favorites” can also be copied to USB memory or floppy disk.

Copying Performance Songs from USB Memory to “Favorites”

Connecting the USB memory to the External Memory connector.

If you want to copy performance song from floppy disk, connect the floppy disk drive to the External Memory connector.

Press the Value [-] [+] buttons to select the

performance song you want to copy.

Press the [Rec] button.

Press the Value [-] [+] buttons to select the

10.

copy-destination number.

Numbers for which a song name is shown already have a song saved to them.

11.

Press the [Rec] button to copy the song.

The copying of the song to “Favorites” begins. Once the song has been accommodated in memory, the

Media Utility screen reappears.

Never remove the USB memory or turn off the power while the performance song is being copied from USB memory into the ATELIER. If you do so, the not be loaded into the ATELIER, and malfunctions could result.

If you select a number in which a song is already saved, a screen like the following appears.

performance song

will

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Media Utility.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Copy Song.”

fig.02-10.eps

Press the [Rec] button.

If you want to delete the previously saved song and overwrite it with the song you’re newly saving, press the [Rec] button.

If you don’t want to delete the previously saved song, press the [Reset] button, then select a number at which no song has been saved, and copy the song to that number.

Copying Performance Songs from “Favorites” to USB Memory

You can copy performance song from “Favorites” to USB memory.

To do so, press the [Media] button in step 7 to choose “Favorites.”, you’ll be copying performance song from “Favorites” to USB memory.

Press the [Media] button to select the media

(the location of the performance song you want to copy).

If you want to copy a performance song from USB memory, select “Ext Memory.” If you want to copy a performance song from floppy disk, select “Disk.”

The rest of the procedure is the same as when copying performance song from USB memory to “Favorites.”

Record and Playback Your Performance

Enjoying VIMA TUNES Songs

Listening to a VIMA TUNES Song

You can connect a CD drive (commercially available) and play back CD-ROM produced for VIMA TUNES (sold separately). While playing a VIMA TUNES song, you can play along using recommended tones.

VIMA TUNES

VIMA TUNES is a Roland specification for music files that contains image and lyric data, allowing you to enjoy songs with lyrics and images simultaneously. When data bearing the “VIMA TUNES” logo is played back on a device that bears the same logo, lyrics can be shown on the screen of a connected external display or television, letting you enjoy karaoke or watch a slide show.

NOTE

This instrument (AT-75) is not able to play back VIMA TUNES images.

Performing with Sounds that Match the Song (Recommended Tones)

When playing along on the keyboard while listening to a CDROM made for the VIMA (VIMA TUNES), this function lets you play on Upper keyboard using instrumental sounds that are appropriate for the atmosphere of the selected song.

If you select a song from a CD-ROM created for VIMA (VIMA TUNES), three recommended tones will automatically be selected in the VIMA TUNES screen. You can use these three sounds to perform sounds that will match the character of that song.

When you want to select a song from a CD-ROM made for the VIMA (VIMA TUNES), insert the CD-ROM into the CD drive.

Select the song of VIMA CD-ROM.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “VIMA TUNES.”

Connect a commercially available CD drive to

the External Memory connector, and insert the VIMA TUNES CD-ROM into the CD drive.

Press the [Song] button (confirm that its indicator is lit).

The Song Select screen appears.

Press the [Media] button to select “CD.”

Press the Value [-] [+] buttons to select the song you want to play.

Press the [Play/Stop] button to start playback.

Press the [Play/Stop] button to stop playing back the song.

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number

of times to select “Recommended Tone.”

fig.02-10.eps

Press the Value [-] [+] buttons to select a tone.

Press the [Utility] button to return to the basic screen.

Press the [Play/Stop] button to start playing back the song.

Play along with the song.

The tones you play will be suitable for the character of the song.

Record and Playback Your Performance

Press the [Play/Stop] button to stop playing

10.

back the song.

Record and Playback Your Performance

NOTE

Listening to Songs from Music CD

You can connect a commercially available CD drive to the ATELIER and use it to play music CDs. This lets you perform or sing along with the backing of a music CD.

You can’t copy music CD songs to “Favorites.”

NOTE

It will take a certain amount of time until a music CD can be

NOTE

selected.

Connect a commercially available CD drive to the External Memory connector, and insert the music CD into the CD drive.

Press the [Song] button (confirm that its

indicator is lit).

The Song Select screen appears.

Enjoying Karaoke with a Music CD (Center Cancel)

You can minimize the vocal sounds of a commercially available music CD, and sing the vocal part yourself. This is a convenient way to enjoy karaoke or practice soloing with a favorite music CD.

For some songs, the vocal sound may not be eliminated completely.

Connect a commercially available CD drive to

the External Memory connector.

Insert the music CD you want to use into the

CD drive, and select the song you want to sing (p. 96).

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “VIMA TUNES.”

Press the [Media] button to select “CD.”

Press the Value [-] [+] buttons to select the

song you want to play.

Press the [Play/Stop] button to start playback.

To stop playback, press the [Play/Stop] button.

You can press [Bwd] button or [Fwd] button to rewind or fast-forward the playback.

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number of times to select “Melody.”

fig.02-10.eps

Press the Value [-] [+] buttons to select “MUTE/ C.CANCEL.“

The Center Cancel function is active.

Press the [Play/Stop] button to start playing

back the song.

When you play back the song, the sound of the melody or vocal will be minimized.

This lets you perform the melody portion yourself.

Transposing the Song to a Comfortable Key for Singing

You can transpose the song to a key that is more comfortable for you to sing.

If you or someone else will be singing along with a song, you can change the key of the song so it’s appropriate for the singer’s range.

If you select a different song, the playback transpose settings will return to their factory-set state.

Connect a commercially available CD drive to the External Memory connector.

Insert the music CD you want to use into the CD drive, and select the song you want to sing (p. 96).

Record and Playback Your Performance

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number

of times to select “Playback Transpose.”

fig.02-10.eps

Each time you press the Value [-] [+] buttons, the key is changed by one semitone.

Value [-] button to lower the key, or Value [+] button to raise the key.

This can be set in a range of -6–0–+5 (semitone steps).

If you press the Value [-] [+] buttons to select “0,” Key Control will be turned off.

Press the [Play/Stop] button to start playing back the song.

Record and Playback Your Performance

Various Other Settings

Folder Settings

Creating a Folder in USB Memory or User Memory

You can create folders in a connected USB memory device or in User memory.

If you want to create a folder in USB memory, connect the USB memory to the External Memory connector.

About folders

The ATELIER lets you create up to 99 Registration sets or songs. If you create a folder, you’ll be able to save up to 99 sets in each folder.

You can create as many folders as you wish, limited only by the capacity of the media.

It’s a good idea to save the Registrations in a folder for each song.

Assign a name to the folder.

Rename the folder as described in “Changing the Name of a Folder” (p. 98).

To confirm the new name, simultaneously

press the [Registration] and [Media] buttons once again.

The name will be assigned to the newly created folder.

Changing the Name of a Folder

Here’s how to rename a folder.

Press the [Registration] button.

In the Registration Select screen, select the folder that you want to rename.

Press the [Utility] button.

Press the Menu [ ] [ ] buttons a number of times to select “Media Utility.”

Press the [Rec] button.

Press the Menu [ ] [ ] buttons a number

of times to select “Create Folder.”

fig.02-10.eps

Press the [Rec] button.

Press the [Media] button to select the media.

Choose “Favorites” if you want to create a folder in User memory, or “Ext Memory” if you want to create a folder in USB memory.

Press the [Rec] button.

Press the [Registration] and [Media] buttons

simultaneously.

fig.08-10

Press the Menu [ ] [ ] buttons to move the

cursor, and press the Value [-] [+] buttons to select a character.

The following characters can be selected when changing a name:

_ A B C D E F G H I J K L M N O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 7 8 9

Press the [Reset] button.

Press the [Rec] button.

To confirm the new name, simultaneously

press the [Registration] and [Media] buttons once again.

The new name is now inserted.

Delete a character.

Inserts the letter “A.”

Roland AT-75, 5100001499-01, 5100001499 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

USING THE UNIT SAFELY

IMPORTANT NOTES

Main Features

Conventions Used in This Manual

Contents

Panel Descriptions

Before You Start Playing

Setting Up the Music Rest

Connecting the Power Cord

Turning the Power On and Off

Turning On the Power

Using Headphones

Turning Off the Power

Using the Cord Hook

Restoring All the Factory Default Settings (Factory Reset)

Adjusting the Contrast of the Screen

Using the External Memory

Connecting the USB Memory

Connecting the Floppy Disk Drive (Sold Separately)

Using a CD

About the Adjuster

Connecting a CD Drive (Sold Separately)

About the Display

Basic Screens

Selecting and Playing Sounds

Listening to the Demo Songs

Selecting Voices

About the Voices and Parts

Functions of the Upper/Lower/Pedal Bass Sound Select Buttons

Selecting the Upper/Lower/Pedal Bass Voices

Selecting Solo Voice

Selecting a Voice Using the [Others] Button

Creating Organ Sounds (Vintage Organ)

Playing a Vintage Organ Voice

Performing with an Active Expression Voice

Adjust the Volume Balance

Transpose the Pitch in Octave Units (Octave Shift)

Sustaining Notes Played on the Lower Keyboard

Playing Drums from the Entire Lower Keyboard (Drums/SFX)

Changing the Drums/SFX Set

Using the Lower Keyboard to Play the Bass Voice (Bass Split)

Changing the Bass Split Point

Using the Lower Keyboard to Play the Bass Voice (Pedal [To Lower] button)

Using the Rhythm Performance

Selecting a Rhythm

Using Rhythms Stored in User Memory

Playing Rhythm

Starting at the Press of a Button

Starting the Rhythm Automatically When You Play the Lower Keyboard or Pedalboard (Sync Start)

Stopping the Rhythm

Changing a Tempo of Rhythm and Automatic Accompaniment

Playing a Countdown Sound When the Intro Ends

Playing Rhythm and Automatic Accompaniment

Adding Variety to the Rhythm or Automatic Accompaniment

Changing the Arrangement of the Rhythm and Accompaniment (Variation)

Turning Chord Intelligence On/Off

Using the Leading Bass Function

A Simple Way to Make Automatic Accompaniment Settings (One Touch Program)

Using a Rhythm from a USB Memory

Reviewing the Styles on USB Memory

Copying Rhythms

Deleting Saved Rhythm

Using the Registration Buttons

Storing Registrations

Recalling a Registration

How to Recall a Registration

Changing the Timing of Recalling Registrations

Automatically Registering When You Switch Panel Settings

Assigning a Name to a Registration Set

Saving Registration Sets

Loading Previously Saved Registration Sets Into the ATELIER

Loading a Set of Registrations

Loading an Individual Registration

Deleting a Set of Registrations

Copying Registrations

Using the Performance Functions