Rockwell Automation 2711P-RAK12e User Manual

Installation Instructions

Adapter Kit for PanelView 1200/1200e/1400e Keypad Terminal Cutout

Catalog Numbers 2711-NR5K, 2711P-RAK12E

Topic Page

About This Publication 1
Important User Information 2
About the Cutout Adapter Plate 3
Parts List 3
Required Tools 3
Disconnect Power to the Terminal 4
Remove the Existing Terminal from the Panel 4
Attach the Cutout Adapter Plate to the Panel 4
Mount the New Terminal in the Cutout Adapter Plate 5
Additional Resources 6

About This Publication

This publication shows how to use the cutout adapter kit to mount these terminals
into an existing PanelView 1200/1200e/1400e keypad terminal cutout:

• PanelView 1000/1000e keypad

• PanelView Plus 1250 keypad

• PanelView Plus CE 1250 keypad

• RAC6182 12.1 in. keypad

Publication 2711P-IN015C-EN-P - March 2007

2 Adapter Kit for PanelView 1200/1200e/1400e Keypad Terminal Cutout

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical equipment.
Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (publication
SGI-1.1 available from your local Rockwell Automation sales office or online at
http://literature.rockwellautomation.com
equipment and hard-wired electromechanical devices. Because of this difference, and also because of the
wide variety of uses for solid state equipment, all persons responsible for applying this equipment must
satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages
resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many
variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot
assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,
equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell
Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

) describes some important differences between solid state

WARNING

IMPORTANT

ATTENTION

SHOCK HAZARD

BURN HAZARD

Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property
damage, or economic loss.

Identifies information that is critical for successful application and understanding of
the product.

Identifies information about practices or circumstances that can lead to personal injury
or death, property damage, or economic loss. Attentions help you to identify a hazard,
avoid a hazard, and recognize the consequences.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that dangerous voltage may be present.

Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.

Publication 2711P-IN015C-EN-P - March 2007

Adapter Kit for PanelView 1200/1200e/1400e Keypad Terminal Cutout 3

About the Cutout Adapter Plate

The cutout adapter plate is designed to fit into the existing cutout and stud-mounts
for the PanelView 1200/1200e/1400e keypad terminals. See the cutout assembly
dimensions.

Dimensions are given in inches (mm).

13.69
(343)

12.48
(317)

8.48
(215)

5.48
(139)

1.48
(38)

0.29
(7)

0

0.34 (9)

1.85
(46)

0.80 (20)

0

#10-32
Mounting
Studs
TYP 18 PLS.

5.15
(131)

9.5
(242)

15.30
(389)

19.0
(482.6)

13.85
(352)

18.20
(462)

18.66
(474)

1.85
(46)

1.95
(50)

10.07
(256)

1.95
(50)

Front Bezel

13.97
(355)

Gasket

#10-32
Mounting
Studs

0.13 (3)

Parts List

The cutout adapter kit includes these items:

• One keypad cutout adapter plate with gasket and ball bearing spacers

• 18, #10-32 nuts with flat washers

Required Tools

These items are required for installation:

• Socket driver with 3/8 inch socket

• Slot or Phillips screwdriver

• Torque wrench capable of 10 lb-in

Publication 2711P-IN015C-EN-P - March 2007