RocketFish RF-WHD200 User Manual

RF-WHD200 I 4-port Wireless HD Kit
Quick Setup Guide

Introduction

Thank you for purchasing the Rocketsh 4-port WirelessHD Kit. Please follow the steps in this Quick Setup
Guide to ensure a successful installation of this product. If you experience any diculty setting the product

up after referring to this guide, please consult the more detailed User Guide, also included in the package,
which contains some troubleshooting techniques that may help. If the additional instructions and
troubleshooting section of the User Guide prove unsuccessful for your setup, please contact our customer
service department at 800-620-2790 or visit www.rocketshproducts.com for additional assistance.

This product is designed to wirelessly send fully uncompressed signals from up to four HDMI source
devices, such as a Blu-ray player, cable/satellite set-top box, gaming console, laptop, etc., to a HDTV or
projector at a distance of up to 30 feet within the same room. It is important to note that the 60 GHz
frequency with which this product transmits provides the necessary bandwidth to send every bit of
information from the source device to the display with no compression or bit dropping, but does not
penetrate wall or oors. Therefore, this product is not designed to send signals from one room to another.

Package contents

• 60 GHz WirelessHD transmitter

• 60 GHz WirelessHD receiver

• High-speed HDMI cables (2)

• Wall mounting bracket
(for use with the receiver)

• Remote control

• AC power adapters
(2 - one for the transmitter, one for the receiver)

• Quick Setup Guide

• User Guide

Setting up the WirelessHD Kit

Tips:

• Test the placement of the transmitter and receiver for a good signal prior to permanently mounting or
installing everything.

• For best performance and range, mount the receiver vertically on the wall next to the TV (not behind

the TV), or upside-down on the ceiling next to the projector. Make sure that you can see the
Rocketsh and WiHD logos on the receiver from the location in the room where the transmitter is
located. For more details about mounting the receiver, see your User Guide.

• Use only good quality high-speed HDMI cables for all connections, such as Rocketsh brand cables.
Poorly constructed HDMI cables can negatively impact performance and may not support all of the
features included in your connected devices.

• Do not place the transmitter or receiver inside a cabinet or other location where they will not have a
clear view of the room.

Top view Side view

82° 82°

16.4 ft.
(5 m)

Transmitter

Receiver

32.8 ft.
(10 m)

Transmitter Rece iver

32.8 ft.
(10 m)

Floor

16.4 ft.
(5 m)

16.4 ft. (5 m)

47°

47°

16.4 ft. (5 m)

1 Connect your HDMI source devices (up to four) to the WirelessHD transmitter with high-speed

HDMI cables.

HDMI cable(s)

Blu-ray/DVD

2 Connect the WirelessHD receiver to the TV or projector with a high-speed HDMI cable.

HDMI cable

OR

3 Connect the included AC adapters for the transmitter and receiver to the DC input jacks, then plug

them both into an available AC outlet.

Note: The included AC adapters are labeled to ensure the correct adapter is used with the

transmitter and receiver.

4 Power on the TV or projector and at least one of the source devices that is connected to the

transmitter.

Note: Be sure the TV or projector is switched to the HDMI input to which the WirelessHD receiver is
connected.

5 Switch the Power switches on the transmitter and receiver to the ON position (it does not matter

which one you power on rst). The HDMI input port LED on the transmitter should light

continuously (stop blinking) to indicate that the desired input is selected. If this doesn't happen
automatically, use the included remote control or HDMI Select Switch on the back of the
transmitter to select the desired input port. For more details on HDMI port switching, see your User
Guide.

Note: The Power and Link Status indicator LED will ash while the transmitter and receiver establish

a connection. Once the connection has been established, these indicators will light continuously

(stop ashing).
For more detailed instructions on operating the WirelessHD kit, please refer to the included User Guide
section, “Operating the WirelessHD kit”.

Features

Transmitter front/top panel Receiver front/top panel

# Component Description

1 HDMI 4 Lights to indicate that this HDMI input is selected.

2 HDMI 3 Lights to indicate that this HDMI input is selected.

3 HDMI 2 Lights to indicate that this HDMI input is selected.

4 HDMI 1 Lights to indicate that this HDMI input is selected.

5 Power and link status indicator Blinking—Power is on and the transmitter is in sleep mode
(transmitter) or searching for the receiver.
On—The transmitter and receiver are linked.
O—The power is o.

6 Power and link status indicator Blinking—Power is on and the receiver is in sleep mode or
(receiver) searching for the transmitter.
On—The transmitter and receiver are linked.
O—The power is o.

Transmitter back panel

# Component Description

1 DC IN jack Connect the power adapter labeled “Transmitter” to this jack.

2 Power switch Turns the unit on or o.

3 HDMI select switch Press quickly (<1 second) to switch HDMI inputs; or hold for at least
3 seconds to join a Wireless Video Area Network (WVAN). See User Guide
for more information about WVAN.

4 HDMI 1 jack Connect an HDMI source device with a high-speed HDMI cable.

5 HDMI 2 jack Connect an HDMI source device with a high-speed HDMI cable.

6 HDMI 3 jack Connect an HDMI source device with a high-speed HDMI cable.

7 HDMI 4 jack Connect an HDMI source device with a high-speed HDMI cable.

Receiver back and side panels
Left side

# Component Description

1 HDMI jack Connect this por t to an HDMI input on the TV or projector, using a
high-speed HDMI cable.

2 DC IN jack Connect the power adapter labeled “Receiver” to this jack.

3 Power switch Turns the receiver on or o.

4 Cable routing clips Insert HDMI cable into these clips for receiver placement stability.

Remote control

Note: Remove the plastic lm from the remote control before to using it for the rst time.

Important safety instructions

• Keep these instructions.

• Do not use this apparatus near water.

• Clean only with a dr y cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
ampliers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not t into your outlet, consult an electrician
for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.

• Only use attachments or accessories specied by the manufacturer.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all ser vicing to qualied service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• The apparatus shall not be exposed to dripping or splashing and no objects with liquids such as vases, shall be
placed on the apparatus.

For more information on using your 4-port wireless HD kit, see your online User Guide at
www.rocketshproducts.com.

FCC RF Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This
transmitter must not be co-located or operating in conjunction with any other antenna.

Canadian RF Exposure Statement

This equipment is in conformity with the IC radiation exposure limits set forth for an uncontrolled environment. This
device must be installed and used at a distance of at least 20 cm (8 in) between the antenna and the body of the user.
The transmitter should not be placed close to another antenna or another transmitter, or to function with another
antenna or another transmitter.

FCC Part 15 Class B Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is needed.

• Consult the dealer or an experienced radio/TV technician for help.

IC Class B Statement (Canada)

This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Cet appareil numérique de la classe B conforme á la norme NMB-003 et RSS-210 du Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.

FCC Caution:

Any changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate this equipment.

One-year limited warranty

Visit www.rocketshproducts.com for details.

Contact Rocketsh:

For customer service, please call 1-800-620-2790.
www.rocketshproducts.com

Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richeld, MN 55423-3645 USA
© 2011 BBY Solutions, Inc., All Rights Reserved. ROCKETFISH is a trademark of BBY Solutions, Inc. All other products
and brand names are trademarks of their respective owners.
Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca, Programa Parcial de
Desarrollo Santa Fe, Delegación Cuajimalpa, Distrito Federal, México 05349
© 2011 Best Buy UK Distributions Limited. All rights reserved. Distributed by Best Buy Europe Distributions Limited.
1 Portal Way, London W3 6RS

ENGLISH 10-1354