This appliance shall be installed in accordance with:
• Manufacturer’s Installation Instructions
• Current AS/NZS 3000
• Local Regulations and Municipal Building Codes including local OH&S requirements
This appliance must be installed, maintained and removed by an Authorised Person.
For continued safety of this appliance it must be installed and maintained
accordance with the manufacturer’s instructions.
Remote Control Operation Manual
Split Type Air Conditioner
Australia Pty. Ltd.
ABN 74 005 138 769
Rinnai has a Service and Spare P arts network with personnel who are fu lly trained
and equipped to giv e the best service on your Rin nai appliance. If you r appliance
requires serv ice, please call our Nati onal Help Line. Rinnai r ecommends that this
appliance be serviced once a year.
Head Office
100 Atlantic Drive,
Keysborough VIC 3173
P.O. Box 460
Braeside, Victoria 3195
Product Sales and Service - National
Phone: 1300 555 545* Fax: 1300 555 655*
Technical Helpline and Spare Parts
National (Mon-Fri 8am - 5.30pm EST)
Phone: 1300 555 545* Fax: 1300 300 141*
*Cost of a local call higher from mobile or public phones.
E-mail: enquiry@rinnai.com.au
For further information visit: www.rinnai.com.au
Part Number: B063803
December 2016
EQPL38586755
Issue A
cool
SET TEMP.
MODE
SWING
SWING
TURBO
SLEEP
SHORT
CUT
TIMER
ON
FAN
SPEED
LED
TIMER
OFF
LOCK RESET
ON/OFF
TEMP
- +
HINRA26M
HINRA35M
HINRA50M
HINRA70M
HINRA80
CIN050A
Wall Mounted Cassette
CIN070A
CIN100A
CIN120A
To Suit Models
CIN140A
1
CONTENTS
Use the remote control within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote contr ol.
8m
The remote control is powered by two AAA batteries housed under the
removable rear cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new batteries, placing the (+) and (-)
ends correctly.
(3) Reattach the cover by sliding it back into position.
NOTE: When the batteries are removed, the remote control erases all programming. After inserting new batteries, the remote control must be reprogrammed.
Replacing Batteries
Handling the Remot e Control
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote control to the indoor unit.
Prevent any liquid from falling into the remote control. Do not expose
the remote control to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote control, either move
these appliances or consult your local dealer.
2
CAUTIONS
Do not mix old and new batteries or batteries of different types.
Do not leave the batteries in the remote control if they are not
going to be used for 2 or 3 months.
Do not dispose batteries as unsorted municipal waste. Batteries can
be taken to specialist waste transfer stations.
MODE
SWING
TEMP
SHORTCUT
FAN
SPEED
TIMER
OFF
RESET
LOCK
LED
FOLLOW ME
TIMER
ON
TURBO
SELF CLEAN
DIRECT
SLEEP
FRESH
2
3
5
7
8
8
8
9
9
10
Handling the Remote Control .........................................................
Remote Control Specifications......................................................
Function Buttons .................. .........................................................
Indicators on LCD ..........................................................................
System Operation ............................................................................
Auto Operation.................................................................................
Cooling/Heating/Fan Operation......................................................
Dehumidifying (DRY) Operation ......................................................
Adjusting Air Flow Direction ..........................................................
Timer Operation...............................................................................
Model
Rated Voltage
8m
3.0V( 2x AAA 1.5 Volt Batteries)
Remote Control Specifications
1. Operating Modes: AUTO, COOL, DRY, HEAT and FAN.
2. Timer Setting Function in 24 hours.
。 。
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function LCD (Liquid Crystal Display).
Environment
Signal Receiving Range
Performance Features
3 4
RG36F5/BGEF
。 。
-5 C ~ 60 C
NOTE:
Remo te c on tr ol b utton d es ig n ma y be s light ly d if fe re nt from t he o ne
supp li ed d ep en ding on t he i nd iv id ual mod el
All th e fu nc ti on s descr ib ed a re a ss ociat ed w it h th e re lativ e in do or u ni t.
If the i nd oo r un it d oes not h av e a pa rt ic ular fe at ur e, t he re is no
corr es po nd in g opera ti on p er fo rmed by t he i nd oo r un it.
1
2
4
5
3
9
10
8
6
7
11
12
13
14
15
TURBO
SELF
CLEAN
SLEEP
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FOLLOW
ME
FAN
SPEED
SWING
MODE
TEMP
ON/OF F
SWING
Function Buttons
1
2
Each time the button is pressed, the operation
mode is selected in a sequence as follows:
3
MODE Button
4
ON/OFF Button
Operation starts when this button is pressed
and stops when this button is pressed again.
AUTO
COOL
DRY
HEAT FAN
Swing Button
Swing Button
Used to stop or start horizontal louver movement or set the desired up/down air flow
direction. The louver changes 6 degree in angle
for each press. If pressed for more than 2
seconds, the louver will swing up and down
automatically.
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. And the temperature display
area of indoor unit displays for one
second. If pressed for more than 2 seconds,
the vertical louver swing feature is activated.
And the display area of indoor unit displays
IIII , flashes four times, then the temperature setting reverts back. If the vertical louver
swing feature is stopped, it displays LC and
remains on for 3 seconds.
,
,
,
,
,
,
SHORT
CUT
5
SLEEP Button
NOTE: While in SLEEP mode, the SLEEP mode
is cancelled when the FAN or ON/OFF buttons
are pressed.
Active/Disable sleep function. It maintains the
most comfortable temperature and saves energy.
For details, see “SLEEP operation” in “USER’S
MANUAL”.
6
Press this button to initiate the LED function.
Press and hold this button for more than 2
seconds and the FOLLOW ME function is initiated.
When the Follow Me function is activated,
the remote display is actual temperature at
its location. The remote control will send this
signal to the air conditioner at 3 minute intervals
until you press the FOLLOW ME button again.
The Follow Me function is not available under
DRY and FAN mode.
Switching the operational mode or turning off
the unit will cancel the FOLLOW ME function.
TURBO/SELF CLEAN Button:
5 6
Function Buttons
8
Press this button to decrease setting temperature or to decrease Hours during Timer setting.
UP Button ( )
Press this button to increase setting temperature or to increase Hours during Timer setting.
DOWN Button ( )
9
-
+
10
11
Used to select the fan speed in four steps:
AUTO LOW MED HIGH
FAN SPEED Button
TIMER ON Button
12
Press this button to initiate the auto-on time
sequence. Each press will increase the
auto-timer setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timer setting
60 minutes increments. To cancel the
auto-timer program, simply adjust the
auto-on time to 0.0.
TIMER OFF Button
13
Press this button to initiate the auto-off time
sequence. Each press will increase the
auto-timed setting in 30 minutes increments.
When the setting time displays 10H, each
press will increase the auto-timer setting
60 minutes increments. To cancel the
auto-timer program, simply adjust the
auto-off time to 0.0.
1
1
2
2
4
4
5
5
3
3
9
9
10
10
8
8
6
6
7
7
11
11
12
12
13
13
14
14
15
15
TURBO
SELF
CLEAN
TURBO
SELF
CLEAN
SLEEP
SLEEP
SHORT
CUT
SHORT
CUT
TIMER
ON
TIMER
ON
TIMER
OFF
TIMER
OFF
LOCK
LOCK
RESET
RESET
LED
FOLLOW
ME
LED
FOLLOW
ME
FAN
SPEED
FAN
SPEED
SWING
SWING
MODE
MODE
TEMP
TEMP
ON/OF F
ON/OF F
SWING
SWING
14
15
LOCK Button
When you press the recessed LOCK button,
all current settings are locked in and the
remote control does not accept any
operation except that of the LOCK. Press
again to cancel the LOCK mode.
,
,
7
When you press the recessed RESET button,
all current settings are cancelled and the
control will return to the initial settings.
RESET Button:
SHORTCUT Button
Used to restore the current settings or resume
previous settings.
When first connected to power, pressing
the SHORTCUT button will activate the AUTO
O
mode, 24 C, and fan speed is Auto.
Pressing this button when unit is on, the
system will automatically revert back to the
previous settings including operating mode,
setting temperature, fan speed level and sleep
feature (if activated).
If pressed and held for more than 2 seconds,
the system will automatically restore the
current operation settings including operating
mode, setting temperature, fan speed level
and sleep feature (if activated).
LED/FOLLOW ME function
Press this button to initiate the LED function.
Press and hold this button for more than 2
seconds and the FOLLOW ME function is initiated.
When the Follow Me function is activated,
the remote display is actual temperature at
its location. The remote control will send this
signal to the air conditioner at 3 minute intervals
until you press the FOLLOW ME button again.
The Follow Me function is not available under
DRY and FAN mode.
Switching the operational mode or turning off
the unit will cancel the FOLLOW ME function.
7 8
Indicators on LCD
Transmission Indicator
Temp./Timer Display
Fan Speed Display
Silence Display (where fitted)
Sleep Display
Mode Display
ON/OFF Display
This transmission indicator lights when remote
control transmits signals to the indoor unit.
Displays the current operation mode. Including
auto( ), cool( ), dry( ), heat( ),
fan ( ) and back to auto ( ).
O O
Displays the temperature setting(17 C~30 C). When
you set the operating mode to FAN, no temperature
setting is displayed. If in TIMER mode, shows the
ON and OFF settings of the TIMER.
Displayed by pressing the ON/OFF button.
Press the ON/OFF button again to change.
Displays the selected fan speed, AUTO (no display)
and three fan speed levels " " (LOW) " " (MED)
" " (HIGH) can be indicated. The fan speed is AUTO
when the operating mode is either AUTO or DRY.
Displayed when SILENCE function is activated.
Displayed during SLEEP mode.
Press the SLEEP button again to exit SLEEP mode.
Note:
All indicators shown in the figure are for the purpose
of presentation. During the actual operation of the
remote control only the relative functional signs are
shown in the display window.
Lock Display
Displayed when LOCK mode is activated.
FOLLOW ME Display
Displayed when FOLLOW ME function is activated.
F
auto cool dry heat fan
silen ce sle ep fol low me l ock run
SET TEMP. TIMER ONOFF
System Operation
Cooling /Heating/Fan Operation
Ensu re t he u ni t is p lugge d in a nd p ow er i s
avai la bl e.
1. Pre ss t he M OD E bu tton to s el ec t CO OL ,
HEAT or FAN m od e.
2. Pre ss t he U P/ DO WN butt on s to s et t he
desi re d te mp er ature . Th e te mp er ature c an
O O O
be set w it hi n a ra ng e of 17 C~ 30 C in 1 C
incr em en ts .
3. Pre ss t he FA N bu tt on to sel ec t th e fa n sp eed
in fou r st ep s- Auto, L ow, M ed ,o r Hi gh.
4. Pre ss t he O N/ OF F butto n to s ta rt t he a ir
cond it io ne r.
In the FAN mode, the temperature setting is not
displayed on the remote control, and you are unable
to control the room temperature. In FAN mode, only
steps 1, 3 and 4 may be performed.
NOTE
Auto Operation
Ensu re t he u ni t is p lugge d in a nd p ow er i s
avai la bl e. T he O PERATIO N ind ic at or o n th e
disp la y pa ne l of t he indo or u ni t wi ll s tart
flas hi ng .
1. Pre ss t he M OD E bu tton to s el ec t Auto.
2. Pre ss t he U P/ DO WN butt on t o se t th e
desi re d te mp er ature . Th e te mp er ature c an
O O O
be set w it hi n a ra ng e of 17 C~ 30 C in 1 C
incr em en ts .
3. Pre ss t he O N/ OF Fbutt on t o st ar t th e air
cond it io ne r.
1. In the Auto mode, the air conditioner will logically
choose Cooling, Fan, or Heating mode
by sensing the difference between the actual
ambient room temperature and the set point
temperature on the remote control.
2. In the Auto mode, you can not control the fan speed.
It is automatically controlled by the unit.
3. If the Auto mode is not comfortable for you , set the
desired mode manually.
NOTE
3
1
2
4
1
2
3
2
2
TURBO
SELF
CLEAN
SLEEP
SLEEP
SHORT
CUT
SHORT
CUT
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FOLLOW
ME
FAN
SPEED
SWING
MODE
TEMP
ON/OFF
ON/OFF
SWING
TURBO
SELF
CLEAN
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FOLLOW
ME
FAN
SPEED
SWING
MODE
TEMP
SWING
9 10
Dehumidifying (DRY) Operation
Ensu re t he u ni t is p lugge d in a nd p ow er i s
avai la bl e. T he O PERATIO N ind ic at or o n th e
disp la y pa ne l of t he indo or u ni t st ar ts flas hi ng .
1. Pre ss t he M OD E bu tton to s el ec t DRY mod e.
2. Pre ss t he U P/ DO WN butt on s to s et t he
desi re d te mp er ature . Th e te mp er ature
O O
can be s et w it hi n a ra nge of 17 C~ 3 0 C
O
in 1 C incr em en ts .
3. Pre ss t he O N/ OF F butto n to s ta rt t he a ir
cond it io ne r.
In Dehumidifying mode, you can not control the
fan speed. It is automatically controlled by the unit.
NOTE
Adjusting Air Flow Direction
TURBO
SELF
CLEAN
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FOLLOW
ME
FAN
SPEED
SWING
MODE
TEMP
SWING
Use the SWING and SWING buttons to adjust
the desired airflow direction.
1. Press the SWING button, and the horizontal
louver changes 6 degree in angle for each push.
Press and hold for more than 2 seconds, and
the louver will automatically swing up and down.
2. Press the SWING button, and the vertical
louver changes 6 degree in angle for each push.
Press and hold for more than 2 seconds, and
the louver will automatically swing left and right.
NOTE: When the horizontal/vertical louver swing
moves to a position which may affect
the cooling or heating effect of the air
conditioner, it may automatically change
the horizontal or vertical position.
Timer operation
Press the TIMER ON button to set the auto-on
time of the unit. Press the TIMER OFF button
to set the auto-off time of the unit.
1. Press the TIMER ON button. The remote
control shows TIMER ON, the last Auto-on
setting time and the signal "H" will be shown in
the LCD display area. Now it is ready to reset
the Auto-on time to the START time.
2. Press the TIMER ON button again to set desired
Auto-on time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.
3. After setting the TIMER ON function, there will be a
one second delay before the remote control
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "H" will disappear and the set temperature
will re-appear in the LCD display window.
To set the Auto-on time.
To set the Auto-off time.
1. Press the TIMER OFF button. The remote
control shows TIMER OFF, the last Auto-off
setting time and the signal "H" will be shown in
the LCD display area. Now it is ready to reset
the Auto-off time to stop time.
2. Press the TIMER OFF button again to set
desired Auto-off time. Each time you press the
button, the time increases by half an hour
between 0 and 10 hours and by one hour
between 10 and 24 hours.
3. After setting the TIMER OFF function, there will be
a one second delay before the remote control
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "H" will disappear and the set temperature
will re-appear in the LCD display window.
1
2
ON/OFF
SLEEP
SHORT
CUT
3
1
2
2
TURBO
SELF
CLEAN
TIMER
ON
TIMER
OFF
LOCK
RESET
LED
FOLLOW
ME
FAN
SPEED
SWING
MODE
TEMP
SWING
ON/OFF
SLEEP
SHORT
CUT
11
12
The effective operation time set by the remote control for the timer function
is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,
5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,
21, 22, 23 and 24.
CAUTION
!
Example of timer setti ng
Start
Off
6 hours later
(Auto-on Operation)
The TIMER ON feature is useful when you want
the unit to turn on automatically before you return
home. The air conditioner will automatically start
operating at the set time.
To start the air conditioner in 6 hours.
1. Press the TIMER ON button, the last setting
of starting operation time and the signal "H"
will show in the display area.
2. Press the TIMER ON button to display "6.0h"
on the TIMER ON display of the remote
control.
3. Wait for 3 seconds and the digital display
area will show the temperature again. The
"TIMER ON" indicator remains on and this
function is activated.
TIMER ON
Example:
Set
TIMER ON
Stop
On
Set 10 hours later
(Auto-off Operation)
The TIMER OFF feature is useful when you want the
unit to turn off automatically after you go to bed. The
air conditioner will stop automatically at the set time.
To stop the air conditioner in 10 hours.
1. Press the TIMER OFF button, the last setting of
stopping operation time and the signal "H" will
show in the display area.
2. Press the TIMER OFF button to display "10h" on
the TIMER OFF display of the remote control.
3. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
OFF" indicator remains on and this function is
activated.
TIMER OFF
Example:
On
Stop
2 hours later
after setting
Set
To stop the air conditioner 2 hours after setting and
start it again 10 hours after setting.
1. Press the TIMER OFF button.
2. Press the TIMER OFF button again to display
2.0h on the TIMER OFF display.
3. Press the TIMER ON button.
4. Press the TIMER ON button again to display 10h
on the TIMER ON display .
5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function is
activated.
TIMER OFF → TIMER ON
(On → Stop → Start operation)
This feature is useful when you want to stop the air
conditioner after you go to bed, and start it again in
the morning when you wake up or when you return
home.
Example:
COMBINED TIMER
(Setting both ON and OFF timers simultaneously)
Start
10 hours later
after setting
TIMER OF F
TIMER ON O FF
13
14
Example:
TIMER ON → TIMER OFF
(Off → Start → Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.
To start the air conditioner 2 hours after setting,
and stop it 5 hours after setting.
1. Press the TIMER ON button.
2. Press the TIMER ON button again to display
2.0h on the TIMER ON display.
3. Press the TIMER OFF button.
4. Press the TIMER OFF button again to display
5.0h on the TIMER OFF display .
5. Wait for 3 seconds and the digital display area
will show the temperature again. The "TIMER
ON OFF" indicator remains on and this function
is activated.
Off
Stop
Start
2 hours later
after setting
5 hours later
after setting
Set
NOTE: The timer setting (TIMER ON or TIMER
OFF) that occurs directly after the set time will
be activated first.
TIMER ON OFF
This page is intentionally blank
Loading...