Safety is a combination of common sense, staying alert and knowing how
your table saw works. Read this manual to understand this table saw.
Safety Signal Words
DANGER: means if the safety infor-
mation is not followed someone will
be seriously injured or killed.
WARNING: means if the safety information is not followed someone
Before Using The Saw
could be seriously injured or killed.
CAUTION: means if the safe ty infor-
mation is not followed someone may
be injured.
WARNING: Some dust created by
power sa ndin g, sa win g, g rin ding ,
drilling, and other construction
activities contains chemicals
known (to the State of California)
to cause cancer, birth defects or
other reproductive harm . S om e
examples of these chemicals are:
Lead from lead-based paints
• Crystalline silica from bricks
and cement and other masonry
products, and
• Arsenic and chromium from
chemically-treated lumber.
Yo ur risk from these exposures
varies, depending on how often
you do this type of work. To
reduce your exposure to these
chemicals: work in a well ventilated area, and work with
approved safety equipment,
such as those dust masks that
are specially designed to filter
out microscopic particles.
WARNING: To reduce the risk of
mistakes that could cause serious, perma nent injury, do not
plug the table saw in unt i l the following steps have been satisfactorily completed.
• Completely align and align saw
(See “Alignment” section).
• Learn the use and function of the
ON-OFF switch, blade guard,
spreader, anti-kickback device,
miter gauge, rip fence, table insert,
blade elevation and blade bevel lock
controls (See “Getting to Know Your
Table Saw” section).
• Review and understand all safety
instructions and operating procedures in this manual.
• Review the maintenance methods
for this saw (See “Maintaining Your
Table Saw” section)).
3
Page 4
Safety Instructions For Table Saw (continued)
• Find and read all the warning labels found on the saw (shown below).
When Installing Or Moving The Saw
Reduce the Risk of Dangerous
Environment.
• Use the saw in a dry, indoor place
protected from rain.
• Keep work area well lighted.
• Use recomme nded ac cessories.
Consult the owner’s manual for recommended accessories. The use of
improper accessories may cause
risk of injury to persons.
To reduce the risk of injury from
unexpected saw movement.
• Bolt or clamp the saw to firm level
surface where there is plenty of
room to handle and properly support
the workpiece (See “AssemblyMounting Your Saw” section).
• Support the saw so the table is level
and the saw does not rock.
• Put the saw where neither operator
nor bystanders must stand in line
with the sawblade.
• To reduce the risk of injury from
electrical shock, make sure your fingers do not touch the plug’s metal
prongs when plugging in or unplugging the saw.
• Never Stand On Tool. Serious
injury could occur if the tool tips or
you accidentally hit the cutting tool.
Do not store anything above or near
the tool where anyone might stand
on the tool to reach them.
Before Each Use
Inspect your saw.
• To reduce the risk of injury from
accidental starting, turn the switch
off, unplug the saw, and remove the
switch key before raising or removing the guard, changing the cutting
tool, changing the setup, or adjust-
ing anything. Make sure switch is in
OFF position before plugging in.
• Check for alignment of moving
parts, binding of moving parts,
breakage of parts, saw stability, and
any other conditions that may affect
the way the saw works.
4
Page 5
• If any part is missing, bent or broken
in any way, or any electrical part
does not work properly, t urn the saw
off and unplug the saw.
• Replace dam aged or missing parts
before using the saw again.
• Use the sawblade guard, spreader
and anti-kickback pawls for a ny
thru-sawing (whenever the blade
comes through the top of the workpiece). Make sure the anti-kickback
pawls work properly. Make sure the
spreader is in line with sawblade
(See “Assembly-Aligning Blade
Guard” section).
• Remove adjusting keys and
wrenches. Form a habit of checking
for and removing keys and adjusting
wrenches from table top before turning saw on.
• Make sure all clamps and locks are
tight and no parts have excessive
play.
T o Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces
(Kickbacks Or Throwbacks)
Inspect Your Blade.
• Choos e the right blade or cutting
accessory for the material and the
type of cutting you plan to do.
• Use The Right Tool. Don’t force tool
or attachment to do a job it was not
designed for.
• Never use grinding wheels, abrasive
cutoff wheels, friction wheels (metal
cutting blades) wire wheels or buffing wheels. They can fly apart
explosively.
• Cut only wood, wood like or plastic
materials. Do not cut metal.
• Choose and inspect your cutting
tool carefully:
- To reduce the risk of cutting tool
failure and thrown shrapnel (broken pieces of blade), use on ly 10”
or smaller blades or other cutting
tools marked for speeds of 5000
rpm or higher.
- Always use unbroken, balanced
blades designed to fit this saw’s 5/8
inch arbor.
- When thru-sawing (making cuts
where the blade comes through
the workpiece top), always use a
10 inch diameter blade. This keeps
the spreader closest to the blade.
- Do not over tighten arbor nut. Use
arbor wrenches to “snug” it
securely.
- Use only sharp blades with properly set teeth. Consult a professional blade sharpener when in
doubt.
- Keep blades clean of gum and
resin.
- Never use the saw without the
proper blade insert.
Inspect your work area
• Keep work area clean.
• Cluttered areas and benches invite
accidents. Floor must not be slippery from wax or sawdust.
• To reduce the risk of burns or other
fire damage, never use the saw
near flammable liquids, vapors or
gases.
• To reduce the risk of injury, don’t do
layout, assembly, or setup work on
the table while blade is spinning. It
could cut or throw anything hitting
the blade.
5
Page 6
Safety Instructions For Table Saws (continued)
Plan your work
• Use the right tool. Don’t force tool or
attachment to do a job it was not
designed for.
Inspect your workpiece.
• Make sure there are no nails or foreign objects in the part of the workpiece to be cut.
• When cutting irregularly shaped
workpieces, plan your work so it will
not slip and pinch the blade:
- A piece of molding for example,
must lie flat or be held by a fixture
or jig that will not let it twist, rock or
slip while being cut. Use jigs or fixtures where needed to prevent
workpiece from shifting.
• Use a different, better suited type of
tool for work that can’t be made stable.
Plan your cut
• To reduce the risk of kickbacks and
throwbacks - when a part or all of
the workpiece binds on the blade
and is thrown violently back toward
the front of the saw:
• Never cut Freehand. Always use
either a rip fence, miter gauge or fixture to position and guide the work,
so it won’t twist or bind on the blade
and kick back.
• Make sure there’s no debris
between the workpiece and its supports.
• Use extra caution with large, very
small or awkward workpieces.
• Use extra supports (tables, saw
horses, blocks, etc.) for any workpieces large enough to tip when not
held down to the table top. Never
use another person as a substitute
for a table extension, or as additional support for a workpiece that is
longer or wider than the basic saw
table, or to help f e ed, s upport or pull
the work piece.
• Never confine the piece being cut
off, that is, the piece not against the
rip fence, miter gauge or fixture.
Never hold it, clamp it, touch it, or
use length stops against it. It must
be free to move. If confined, it could
get wedged against the blade and
cause a kickback or throwback.
• Never cut more than one workpiece
at a time.
• Never turn your table saw “ON”
before clearing everything except
the workpiece and related support
devices off the table.
Plan Ahead To Protect Your Eyes, Hands, Face and Ears
Dress for safety
• Do not wear loose clothing, gloves,
neckties or jewelry (rings, wrist
watches). They can get caught and
draw you into moving parts.
• Wear nonslip footwear.
• Tie back long hair.
• Roll long sleeves above the elbow.
• Noise levels vary widely . To reduce
the risk of possible hearing damage,
wear ear plugs or muffs when using
table saw for hours at a time.
• Any power saw can throw foreign
objects into the eyes. This can result
in permanent eye damage. Always
wear safety goggles, not glasses
complying with ANSI Z87.1 (or in
Canada CSA Z94.3-99) shown on
package. Everyday eyeglasses
have only impact resistant lenses.
They are not safety glasses. Safety
goggles are available at many local
6
Page 7
retail stores. Glasses or goggles not
in compliance with ANSI or CSA
could seriously hurt you when they
break.
• For dusty operations, wear a dust
mask along with safety goggles.
Plan the way you will push the
workpiece through.
• Never pull the workpiece through.
Start and finish the cut from the front
of the table saw.
• Never pu t your fingers or hands in the path of the sawblade or other
cutting tool.
• Never reach in back of the cutting
tool with either hand to hold down
workpiece, support the workpiece,
remove wood scraps, or for any
other reason.
• Reduce the risk of hand positions
where a sudden slip could cause fingers or hand to move into a sawblade or other cutting tool.
• Don’t overreach. Always keep good
footing and balance.
• Push the workpiece against the
rotation of the blade, never feed
materia l into the cutt ing to ol from the
rear of the saw.
• Always push the workpiece all the
way past the sawblade.
• As much as possible, keep your
face and body to one side of the
sawblade, out of line with a possible
kickback or throwback.
• Set the cutting tool as low as possible for the cut you’re planning.
Reduce the Risk of Accidental
Starting
• Make sure switch is “OFF” before
plugging saw into a power outlet.
Whenever Sawblade Is Spinning
WARNING: Do n't al low famil iarity
(gained f rom f requent use of
your table saw) to cause a careless mistake. Always remember
that a careless fraction of a second is enough to cause a severe
injury.
• Before actually cutting with the saw,
watch it while it runs for a short
while. If it makes an unfamiliar noise
or vibrates a lot, stop immediately.
Turn the saw off. Unplug the saw.
Do not restart until finding and correcting the problem.
• Make sure the top of the arbor or
cutting tool turns toward the front of
the saw.
Keep Children Aw ay.
• Keep all visitors a safe distance
from the table saw.
• Make sure bystanders are clear of
the table saw and workpiece.
Don’t Forc e Tool.
• Let the blade reach full speed
before cutting.
• It will do the job better and safer at
its designed rate.
• Feed the workpiece into the saw
only fast enough to let the blade cut
without bogging down or binding.
Before freeing jammed material .
• Turn switch “OFF”.
• Wait for all moving parts to stop.
• Unplug the saw.
• Check blade, spreader and fence
for proper alignment before starting
again.
7
Page 8
Safety Instructions For Table Saws (continued)
To reduce the risk of throwback of
cut off pieces.
• Use the guard assembl y.
To remove loose pieces beneath or
trappe d in sid e the guard.
• Turn saw “OFF”.
• Remove switch key.
• Wait for blade to stop before lifting
the guard.
Additional Safety Instructions For:
Rip Type Cuts.
• Never use the mite r gauge when ripping. Store the miter gauge in the
area provided in the base.
• Use a push stick whenever the
fence is 2 inches or more from the
blade.
• When thru-sawing, use an auxiliary
fence and push block whenever the
fence must be between 1/2 and 2
inches from the blade.
• Never thru-saw rip cuts narrower
than 1/2 inch. (See “Basic Saw
Operations-Ripping and Bevel Ripping” sections.)
• Never rip an yt hi ng s ho rt er t han 10 ”
long.
• When using a push stick or push
block, the trailing end of the board
must be square. A push stick or
block against an uneven end could
slip off or push the work away from
the fence.
• A Featherbo ard can help guide the
workpiece. (see ”Basic Saw Operation-Using Featherboards for ThruSawing.” section)
• Always use featherboa rds for any
non thru rip type cuts. (See “Basic
Saw Operations - Using Featherboards for Non-Thru Sawing” section).
Before Leaving The Saw.
• Turn the saw off.
• Wait for blade to stop spinning.
• Unplug the saw.
• Make workshop child-proof. Lock
the shop. Disconnect master
switches. Remove the yel low switch
key. Store it away from children and
others not qualified to use the tool.
See “Work Feed Devices” section for
Featherboard
Material and Dimensions
Before Starting.
• To reduce the risk of kickbacks and
slips into the blade, make sure the
rip fence is parallel to the sawblade.
• Before thru-sawing, check the antikickback pawls. Th e pawls m ust
stop a kickback once it has started.
Replace or sharpen anti-kickback
pawls when points become dull.
(See “Maintaining Your Table Saw Anti-Kickba ck Pa wls” section.)
• Plastic and composition (like hardboard) materials may be cut on your
saw. However, since these are usually quite hard and slippery, the antikickback pawls may not stop a kickback. Therefore, be especially careful in your setup and cutting
procedures.
While Thru-sa w ing.
• To reduce the risk of kickbacks and
slips into the blade, always push forward on the section of the workpiece between the sawblade and
the rip fence. Never push forward on
the piece being cut off or directly in
line with the blade.
8
Page 9
Additional Safety Instructions For:
Crosscut T y pe Cuts .
• Never use the rip fence when crosscutting.
• An auxiliary wood facing attached to
the miter gauge can help prevent
workpiece twisting and throwbacks.
Attach it to the slots provided. Make
the facing long enough and big
enough to support your work. Make
sure, however, it will not interfere
with the sawblade guard.
Before Starting
• Use jigs or fixtures to help hold any
piece too small to extend across the
full length of the miter gauge face
during the cut. This lets you properly
hold the miter gauge and workpiece
and helps keep your hands away
from the blade.
While Cutting
• To reduce the risk of blade contact,
always hold the miter gauge as
shown in “Basic Saw Operations Using The Miter Gauge”.
Glossary of Terms for Woodworking
Anti-Kickback Pawls
Device which, when properly maintained,
is designed to stop the work piece from
being thrown towards the front of the saw
at the operator during ripping operation.
Arbor
The shaft on which a cutti ng tool is
mounted.
Bevel Cut
An angle cutting operation made through
the face of the workpiece.
Compound Cut
A simultaneous bevel and miter crosscutting operation.
Crosscut
A cutting operation made acr oss the width
of the workpiece.
Dado
A non thru cut which produces a square
sided notch or trough in the workpiece.
Featherboard
A device which can help guide workpieces during rip typ e operation.
Freehand
Performing a cut without the use of fence
(guide), miter gauge, f ixtur e, hol d down or
other proper device to pr event the workpiece from twisting during the cutting
operation. Twisting of the workpiece can
cause it to be thrown.
Gum
A sticky, sap based residue from wood
products.
Heel
Misalignment of the sawblade such that
the blade i s not p arall el t o the mit er gauge
groove.
Kerf
The amount of material removed by the
blade in a through cut or the slot produced
by the blade in a nonthrough or parti al cut.
Kickback
An uncontrolled grabbing and throwing of
the workpiec e back t oward the front of the
saw.
Leading End
The end of the workpiece which, during a
rip type operation, is pushed i nto the cutting tool first.
Miter Cut
An angle cutting operation made across
the width of the workpiece.
Molding
A non through cut which produces a special shape in the workpiece used for joining or decora tion.
Ploughing
Grooving with the grai n the length of the
workpiece, using the fence. (A type of
non-through cut.)
9
Page 10
Glossary of Terms for Woodworking (continued)
Push Stick
A device used to feed the workpiece
through the saw during narr ow ripping
type operations which helps keep the
operator’s hands well away from the
blade.
Push Block
A device used for ripping type operations
too narrow to allow use of a push stick.
Rabbet
A notch in the edge of a workpiece. (A
type of non-through cut)
Resin
A sticky, sap based substance that has
hardened.
Revolutions Per Minute (RPM)
The number of turns complet ed by a spinning object in one minute.
Rip Cut
A cutting operati on along t he lengt h of the
workpiece.
Sawblade Path
Cross Cut
Molding
Kerf
The area of the workpiece or table top
directly in line with either the travel of the
blade or the par t of the work piece which
will be, or has been, cut by the blade.
Set
The distance that the tip of the sawblade
tooth is bent (or set ) out ward from the
face of the blade.
Throw-Back
Throwing of pieces in a manner similar to
a kickb ack.
Thru-Sawing
Any cutting operation where the blad e
extends com p letely through the thickness
of the workpiece.
T railing End
The workpiec e end last cu t by t he bl ade i n
a ripping operation.
Workpiece
The item on which the cutting operation is
being performed. The surfaces of a workpiece are commonly referred to as fa ces,
ends, and edges.
Rip Cut
Dado or
Ploughing
Bevel Cut
Miter Cut
Rabbet
Compound
Cut
10
Page 11
Motor Specificat ions and Electrical Requirements
Power Supply and Motor
Specifications
WARNING: To reduce the risk of
electrical hazards, fire hazards or
damage to the tool, use proper
circuit pro te ct i on. Your tool is
wired at the factory for operation
using the voltage shown. Connect tool to a power line with the
appropriate voltage and a 15amp branch circuit. Use a 15amp time delay type fuse or circuit breaker. T o reduce the risk of
shock or fire, if power cord is
worn or cut, or da m aged in any
way, have it replaced immediately.
General Electrical Connections
The A-C motor used on this tool is a uni versal non-reversible type, having the following speci fi cations.
Voltage120
Amperes15
Hertz (C y cles)60
PhaseSingle
RPM4000
Rotation of ShaftCounterclockwise
(Blade E nd)
DANGER: To reduce the risk of
electrocution:
1. Use only identical replacement parts when servicing.
Servicing should be performed by a qualified service
technician.
2. Do not use in rain or where
floor is wet.
This tool is intended for
indoor residenti al use only.
110-120 Volt, 60 Hz. Tool Information
The plug supplied on your tool may not fi t
into the outlet you are planning to use.
Your local electrical code may require
slightly different power cord plug connections. If these differences exist refer to
and make the proper adjust m ents per
your local code before your tool is
plugged in and turned on.
In the event of a malfuncti on or breakdown, grounding provides a path of least
resistance for electric current to reduce
WARNING: Do not permit fingers
to touch the terminals of plug
when installing or removing the
plug to or from the outlet.
the risk of electric shock. This to ol is
equipped with an electric cord having an
equipment-grounding conductor and a
grounding pl ug, as shown. The plug must
be plugged into a matc hing outlet that is
properly in stalled and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will
not fit the outl et, have the proper outle t
installed by a qual ified electrician.
11
Page 12
Motor Specificat ions and Electrical Requirements
(continued)
A temporary adapter may be used to connect this plug to a 2-pron g outl et as
shown if a properly grounded three prong
outlet is not available. This temporary
adapter should be used only until a properly grounded three prong outlet can be
installed by a qualified electrician. The
green colored rigid ear, lug or the like,
extending from the adapter must be connected to a permanent gro und such as a
properly grounded outlet box.
Improper connection of the equipmentgrounding conduct or can resul t in a risk of
electric shock. The conductor with insulation having an outer surface that is green
with or without yellow stripes is the equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipmentgrounding conductor to a live terminal.
If the grounding instructions are not com pletely understood, or if you are in doubt
as to whether the tool is properly
grounded check with a qualified elect ri cian or service personnel.
WARNING: If not properly
grounded, this tool can cause an
electrical shock, particularly
when used in damp locations, in
proximity to plumbing, or out of
doors. If an electrical shock
occurs there is the potential of a
secondary hazard, such as your
hands contacting the sawblade.
Properly
Grounded
3-Prong Outlet
Grounding Lug
3-Prong
Plug
Adapter
NOTE: The adapter illus tr ated is for use
only if you already have a properly
grounded 2-prong outlet.
NOTE: In Canada the use of a temporary
adapter is not permit ted by the Canadian
Electrical Code.
3-Prong Plug
Grounding
Prong
Make sure this
Is Connected
to a Known
Ground
2-Prong
Outlet
12
Page 13
CAUTION: To reduce the risk of
motor damage, this motor
should be blown out or vacuumed frequently to prevent sawdust buildup which will interfere
with normal motor ventilation.
1.Frequent “blowing” of fuses or tripp ing
of circuit breakers may result if:
a. Motor is over loaded - Overloading
can occur if you feed too rapidly or if
saw blade is dull or misaligned.
b. Motor circuit is fused differently from
recommendations - Always follow
instructions for the proper fuse/
breaker. Do not use a fuse/br eaker of
greater capacity without consulting a
qualified el ectrician.
c. Low voltage - Although the motor is
designed for operation on the voltage
Thermal Overload Protec tor
This saw is equipped with a thermal overload device which will automatically “tri p”
and cause the saw to shut down if the
motor is overheating due to continuous
heavy cutting or stalling.
The overload device can only be reset
manually by the user after the motor has
been allowed to adequately cool. Allow
15-30 minutes.
Should the overload protector “trip”:
1.Turn switch off and remove key.
2. Remove workpiece.
and frequency specified on motor
nameplate, normal loads will be handled safely on voltage not more than
10% above or below the nameplate
voltage. Heavy loads, however,
require that voltage at motor terminals equals the voltage specified on
nameplate.
2.Most motor troubles may be traced to
loose o r i nco r rec t co nnec t io ns , ov er lo ad ing, reduced inp ut voltage (such as
small size wire in the supply circuit or
extension cord) or to ov erly long supply
circuit wire or extension cord. Always
check the connections, the load and the
supply circuit whenever motor fails to
perf orm satisfactor ily. C heck wire sizes
and length with the Wire Size Chart
below.
3.Wait 15-30 minutes.
4.Push in on the reset button.
5.If motor has cooled, button will remain
in.
Thermal Overload
Device
Wire Sizes
NOTE: Make sure the proper extension
cord is used and is in good condit ion.
The use of any extension cor d wil l cause
some loss of power. T o keep this to a minimum and to prevent overheating and
motor burn-out, use the t able shown to
determine the min imum wire size (A. W. G . )
extension cord.
Use only 3-wire extension cords which have
3-prong grounding type plugs and 3-prong
receptacles which accept the tool’s plug.
Extension
Cord Length
0-25 Ft.
26-50 Ft.
13
Gauge
(A.W.G.)
14
12
Page 14
Unpacking and Checking Contents
Unpacking
Separate saw and all parts from packing
materials and check each one with the
illustrati on and the “Li st of Loose Parts ” to
make certain all it em s are accounted for,
before discarding any packing material.
Call 1-866-539-1710 or E-mail us at
info@ridgidwoodworking.com if any p arts
are damaged or missing.
WARNING: If any parts are missing, do not attempt to use the
table saw, plug in t he power cord
or turn the switch on until the
missing parts are obtained and
are installed correctly.
WARNING: The saw is heavy. To
reduce the risk of back injury,
hold the saw close to your body.
Bend your knees so you can lift
with your legs, not your back.
Use hand holds provided.
WARNING: For your own safety,
never connect plug to power
source outlet until all assembly
steps are complete, and you
have read and understand the
safety and operating instructions.
List of Loose Parts
ItemPart NameQty.
A Table Saw Assembly....................... 1
B Miter Gauge............................... ...... 1
C B lade Guard and Spr eader..............1
D Rip Fence.. .. .................... .. ... ......... .. 1
E Arbor Wrenches .............................. 2
ItemPart NameQty.
F Sa fe ty Key. .. ... .......... .. .. .......... ... .. ....1
G Blade Storage Washers...................2
H Blade Storage Wingnut .. ........ ..........1
J Operators Manual.......... .......... ........1
A
B
C
14
D
F
E
G
H
J
Page 15
Getting to Know Your Table Saw
3T able Extension
Lock Lever
1 Rip Fence
15Miter Gauge
14Table
Front Fence
Rail
4 Sliding Table
Extension
5 Rip Fence
Storage
12On-Off
Switch
13 Thermal
Overload
Device
11 Blade Tilt
Lock Lever
Rear Fence
Rail
9 Elevation/Bevel
Handwheel
10 Blade Elevation
16Blade Guard
Lock Knob
8 Blade Tilt
Scale
17Ind-I-Cut
2 MicroAdjust
Rip Fence
6 MIter Gauge
Storage
7Two-Piece
Base
18Carry
Handles
19Tabl e Insert
23Blade Guard Sto rage
for Non-thru Cuts
and Transportation Only
22Sawdust
Ejection Port
15
20Wrench & Blade
Storage
21Cord Wrap
Page 16
Getting to Know Your Table Saw
1. Rip Fence...i s locked in place by
pushing the l ock l ever d own u ntil the
lever rest s on the stop. To move the
fence, lift t he lock lever and grasp
the fence with one hand at the front.
“T” slot s are pr ovided i n the r ip fence
for attaching a wood facing when
using the dado head, or molding
head.
2. Micro-Adjust Rip Fence...allows
the operator to accurately adjust the
rip fence using only one hand. To
move the fence push in on the
micro-adjust knob and rotate.
3. Table Extension Lock
Lever...Locks the sliding table exten-
sion.
4. Sliding Table Extension
additional wor king surfa ce to support
large workpieces and increase rip
capability.
5. Rip Fence Stor age...holds t he
fence when not being used.
6. Miter Gauge Storage...holds the
miter gauge when not being used.
7. Two-Piece Base...supports table.
For additional stability, holes are provided in base to bolt the saw to a
workbench or stand or sawhorses.
8. Blade Bevel Scale.. .shows the
degree the blade is beveled.
9. Elevati on/Bevel Handwheel
a. Elevates or lowers the blade.
Turn the knob clockwise to elevate, counterclockwise to lower.
b. Use the knob to quickly tilt the
blade from 0° to 45°. Rotate the
outer hub for finer adj ustments.
When the blade is tilt ed to th e lef t
as far as it will go, it should be at
45° to the table and the bevel
...provides
pointer should point to 45°.
NOTE: There are limit stops
inside the saw which prevent the
blade from tilting beyond 45° to
the left and 0°. (See “Adjustments and Alignments” section
“Blade Bevel, or Squar eness of
Blade to Table”).
10. Blade Elevation Lock Knob...locks
the blade at the desired hei g ht.
11.Blade Bevel Lock Lever...locks the
blade in the desired bevel positio n.
Lift the lever to the right to unlock
push to th e le ft to loc k .
12. On-Off Switch
CAUTION: Before turning switch
“ON”, make sure the blade
guard is correctly installed and
operating pro perly.
The On-Off Switch has a locking fea-
ture. This feature is intended to help
prevent unauthorized and possible
hazardous use by child ren and others.
a. To turn saw ON, insert key, stand to
either side of the bl ade, never in line
with it, place finger under switch
lever and pull end of lever out.
After turning switch ON, always allow
the blade to come up to full speed
before cutting. Do not cycle the
motor switch on and off rapidly, as
this may cause the sawblade to
loosen. In the event this should ever
occur, allow the sawblade to come to
a complete stop and retighten the
arbor nut normally, not excessively.
Never leave the saw while the power
is ON.
16
Page 17
b. To turn saw OFF, PUSH lever in.
Never leave the saw until the cutting
tool has come to a complete stop.
c. To lock switch in OFF position, hold
switch IN with one hand, REMOVE
key with other hand.
WARNING: For your own safety,
lower blade or other cuttin g tool
below table surface. (If blade is
tilted, return it to vertical, 90°,
position.) Always lock the
switch “OFF”. When saw is not
in use, remove key and keep it in
a safe place. Also, in the event
of a power failure (all of your
lights go out) turn switch off,
lock it and remove th e key. This
will prevent the saw from starting up again when the power
comes back on.
Key
Switch
13. Thermal Overload Device...opens
the power line circuit when the motor
temperature exceeds a safe level,
when the motor is overloaded or
when a lower voltage condition exists.
It can be reset by pressing the reset
button after the motor returns to normal temperate.
14. Table...provides wor king surface to
support workpieces.
15. Miter Gauge...head is locked in
position for cross cutting or mitering
by tightening the lock knob. Always
securely lock it when in use.
a. T here are adjust able s cre w stops
for the stop pin 0° and 45° right
and left posit ions f or c onven ientl y
setting the miter gauge to cut
miters at these standard angles.
16. Blade Guard
Use the sawblade guard, spreader
and ant i-kickback pawls for any thrusawing (whenever the blade comes
through the top of the workpiece).
Make sure the anti-kickback pawls
work properly. Make sure the
spreader is in line with sawblade.
(See “Aligning Blade Guar d” section)
To remove the guard for special
operations, loosen the blade guard
locking knob. Do not disturb the setting of the spreader bracket.
When replacing the guar d, position
the two (2) locator pins on the blade
guard into the m atching holes in the
cradle. Securely ti ghten the blade
guard locking knob.
17
Page 18
Getting to Know Your Table Saw (continued)
17. Ind-I-Cut
The plastic disk em bedded in the
table in f ront of the sawblade, is provided for marking the locat ion of the
“sawcut” (kerf) on the workpiece.
Check disk location: If it is above
table surfa ce, place a piece of hardwood on top of it and tap it down
with a hammer.
18. Carry Handles...grasp the t able
here when picking up t he saw.
19. Table Insert
Is removable for removing or install-
ing blade or other cutting tools.
WARNING: For your own safety
turn switch "OFF" and remove
plug from power source before
removing insert.
To remove the insert.
a. Make sure saw is off and
unplugged.
b. Lower the blade below the table
surface.
c. Raise blade guard.
d. Loosen flat head screw.
e. Lift insert from front end, and pull
toward front of saw.
WARNING: To reduce the risk of
injury from a thrown wo rkpiece,
blade parts, or blade contact,
never operate saw without the
proper insert in place. Use the
sawblade insert when sawing.
Use the dado/molding head
insert when using a dado blade
or molding head.
20. Wrench/Blade Storage...conve-
niently stores arbor wrenches as
well as extra sawblade or dado/
molding blades.
21. Cord Wrap...wrap po w e r cord
around holder and secure by attaching plug with clip to cord.
22. Sawdust Ejection Port
Your table saw i s equipped with a
vacuum hookup. This feature will
allow you to attach any st andard 21/2 inch diameter wet/dry vacuum
hose into the hole provided for convenient sawdust removal.
WARNING: Sawdust can clog
motor. Motor could ignite sawdust. Even if saw is connected
to vacuum, blow out sawdust
regularly.
23. Blade Guard Storage ...holds the
blade guard when making non- thru
cuts and transporting saw.
18
Page 19
Blade Guard Storage
Holds the blade guard when making nonthru cuts and transporting saw. Slide
blade guard in as shown. Snap bottom
edge of clear basket between latches on
base.
Wren c h/Bla de Stora ge
Conveniently stores arbor wrenches as
well as an extra sawblade. Secure
wrenches and sawblade with blade storage washer and wing nut. Extra washers
are provided to separate blades and prevent tooth damage.
Guard
Latches
Blade
Wrench
Wing Nut
Rip Fence Storage
Securely holds the rip fence when it is not
being used. To insert, place the top edge
in first and twist upwar d to snap in place.
To remove pull up on fence and rotate
bottom away from saw.
Miter Gauge Storage
Provides conveni ent storage for the miter
gauge when it is not bei ng used. Slide
miter gauge in place as shown. To
remove miter gauge release latch and lift
straight up.
Fence
Latch
Miter Gauge
19
Page 20
Alignment
Tools Needed
Phillips Screwdriver
Combination Wrenches
3/8, 7/16 In. 1/2 In. 9/16 In.
Combination
Square
Hex “L” Wrenches
3/32 In., 5/32 In., 3/16 In.
Remove Foam Motor Supp ort
A block of foam was placed under the
motor at the factory for shipping. Lift up
one edge of t he s aw base an d r emove the
foam.
Checking Table Insert
WARNING: To reduce the risk of
injury from accidental start, make
sure switch is “OFF” and plug is
not connected to power source
outlet.
1.Insert should be flush with table top.
Check as shown. Loosen fl at head
screw that holds insert and adj ust the
four set screws as nec essary. Ti ghten
flat head screw . Do not tighten sc rew to
the point where it bends the insert.
CAUTION: Insert must be even
with the table surface. Inserts too
high or lo w ca n le t t he w or kpi e ce
“snag” or catch on uneven
edges. Workpiece could twist
and kickback.
2.To remove insert.
a. Make sure saw is of f and unplugged.
b. Loosen flat head screw.
c. Lift insert from front end, and pull
toward front of saw.
3.To replace insert.
a. Make sure saw is of f and unplugged.
b. Place insert into insert opening in
table and push t oward rear of saw to
engage spring clip and until keyslot
in insert will drop over flat head
screw. Tighten screw .
c. Do not tighten screw to the point
where it bends the insert.
Combination Square must be true. Check
it’s accuracy as shown below.
Draw light line on
board along edge
Combination
Square
Shou ld be no gap or overlap here when
square is flipped over in dotted position.
Select the straight edge of
3/4” thick board. This edge
must be perfectly straight.
NOTE: The square and
straight edge are used to
align the saw. They must
be accurate if the saw is
to be aligned properly .
3/32 In.
Hex “L” Wrench
Table Insert
Flat Head
20
Screw
Page 21
Checking Heeling Adjustment or
Parallelism of Sawblade to Miter
Gauge Groove
While cutti ng, the materi al must mov e i n a
straight line parallel to the sawblade.
Therefore, both the mit er gauge groove
and the rip fence must be parallel to the
sawblade.
WARNING: The blade must be
parallel to the miter gauge
groove. Misaligned blades cou ld
bind on workpiece. Workpiece
could suddenly kickback. You
could be cut or hit.
If the sawblade is not parallel to the miter
gauge groove, the blade will bind at one
end of the cut. This is known as “H eeling”.
WARNING: To reduce the risk of
injury from accidental start, make
sure switch is “OFF” and plug is
not connected to power source
outlet.
To check for parallelism:
1.Raise blade all the way up.
2.Mark an “X” on one of the t eeth which
is set (bent) to the right .
3.Place the head of a combination
square in the groove. Adjust blade of
square so that it just touc hes the tip of
the marked tooth.
4.Move square to rear, rotate blade to
see if marked tooth again touches
blade of square.
5.If tooth touches square the same
amount at front and rear, sawblade is
parallel to mit er gauge groove.
6.If tooth does not touch the same
amount, the mechanism underneath
must be adjust ed to make the blade
parallel to groove.
WARNING: To reduce the risk of
injury from accidental start, make
sure switch is “OFF” and plug is
not connected to power source
outlet.
Marked
Tooth
Combination
Square
Alignment
Sawblade
x
Miter Gauge
Groove
Screws
21
Page 22
Alignment (contin ue d)
NOTE: Always review the sect ion "Check -
ing Blade Parallel to the Miter Gauge
Groove" before proceeding with this section.
7.Loosen 1/2 turn the four alignment
screws in the top of table next to the
sawblade. This will allow the mechanism below the table to be shi fted
sideways.
CAUTION: Blade tips are sharp,
to move, grasp blade as shown
to avoid injury.
8.Push on side of blade and move it to
either the ri ght or left as needed to
make the square touch the same
amount front and rear. Tighten one
screw.
9.Check with square to determine if
marked tooth t ouches square by the
same amount at front and rear.
If it does, alternate ly tighten th e other
three screws.
If it doesnot, loosen screw and move
blade the required amount.
10.Recheck blade clearance to table
insert to make sur e blade does not hit
at either 90 or 45 degree blade ti lt.
Alignment
Screws
22
Page 23
Checking Blade Tilt, or Squareness
of Blade to Table
When the bevel poin ter i s point ing di rectly
to the “0” mark on the bevel scale, the
sawblade should make a square cut 90°
to the table.
WARNING: For your own safety,
turn switch “OFF” and remove
plug from po we r so urce outlet.
To Check For Squareness, 90°
Position
1.Raise blade all the way up.
2. Loosen the blade tilt lock lever and push
the elevation wheel in and to the left as
far as possible and tighten the blade tilt
lock lever.
3.Place the s quare against blad e. Make
sure square is not touching the tip of one
of the saw teeth.
A.If blade is square to tabl e
1.Check pointer. If pointer does not
point to the “0” mark on the bevel
scale, loosen the pointer adj usting
screw and adjust pointer using
medium screwdriver. Reti ghten
screw .
Square
Blade
Pointer at
0° Position
B.If blade is not square to table, the
90° stop screw must be adjusted.
1.Loosen 90° stop screw thr ee to
four turns using 5/32 inch hex “L”
wrench.
2.Loosen blade tilt lock lever. Turn
handwheel unti l blade is 90° to t he
table. Tighten blade tilt lock lever.
3.Screw 90° stop screw in until it
stops. Check for squareness and
readjust scr ew, if necessary.
4.Check pointer as descri bed in
step A.
90°
Stopscrew
23
Page 24
Alignment (contin ue d)
T o check for alignment, 45° Position
1.Loosen the blade tilt lock lever and
push elevati on wheel in and to the right
as far as possible and tighten the blade
tilt lock leve r.
2.Place an accur ate sq uar e again st bla de.
Make su r e squa r e is no t touc hi ng t he tip
of one of the saw teeth.
A.If blade is 45° to table;
1.Check pointer. If pointer does not
point to the 45° mark on the scale,
the scale must be ad justed.
2.Loosen two screws on scale and
adjust scale up or down until
pointer points to 45° mark.
Scale Screws
B. If blade is not 45° to table, stop
screw and scale must be adjusted .
1.Loosen 45° stop screw thr ee to
four turns using 5/32 inch setscrew wrench.
2.Loosen blade tilt lock lever. Turn
handwheel unti l blade is 45° to t he
table. Tighten blade tilt lock lever.
3.Screw 45° stop screw in until it
stops. Check once again and
readjust scr ew, if necessary.
4.Check pointer as de scribed in step
A above.
45°
Stopscrew
24
Page 25
Adjusting Rip Fence Guide Bars
Aligning Rip Fence Guide Bars
1.Position rip fence ove r ri ght end of main
table. Whi le holding up rear of rip fence
engage front end of rip f ence onto the
front guide bar. Now lower rip fence
down on to table.
2.Open owners manual so that 8 pages
are separat ed f rom the r est of the book.
Use these pages like a feeler gage to
set the spaci ng between the bottom of
the fence and the t able top.
3.Rip fence should clear saw table surface just en ough to al low ei ght pa ges t o
slide back and forth under rip fence. If
rip fence is too high or too low, loosen
the four nuts under the table and the
screw that secures rip scale at front of
main table. Release table lock, position
fence inside table extension lock lever.
Adjust front bar up and down as
required. Wrench tighten front right nut
only.
4.Adjust rear guide bar, as not ed above.
Wrench tighten rear right nut.
5. Reposition fence over left end main table.
6.Adjust front guide bar up or down as
needed so the rip fence clears the saw
table surface just enough to allow the 8
pages of the owners manual to sl ide
back and forth under neath the rip
fence. Wrench tighten the front lef t nut
first and then the ot her remaining two
nuts at the front of the main table.
7.Adjust rear guide bar, as not ed above.
Wrench tighten the rear left nut first
then the other two nuts at the rear of
the main table .
8.Slide fence left and right over main
table to insure clearance.
9.Tighten rip scale hold down screw.
Owners Manual
8 Pages
Rip Scale
Hold Down
25
Page 26
Alignment (contin ue d)
Aligning Sliding Table Extension
1. Lock table extension lever.
2.Loosen the four nuts underneath the
sliding table extension.
3.Use a combination square to make su re
the top of the slidi ng table extension is
the same height as the mai n table.
4.Tighten four nuts. Recheck and readjust if necessary.
Rip Fence Al ignment Adju st m ent
WARNING: A misaligned fence
can cause kickbacks and jams.
To reduce the risk of injury, follow these instructions until the
fence is pr operly aligned.
The rip fence must be PARALLEL with
the sawblade and miter gauge grooves.
Clean any debris off the fence gui de bars.
Move fence until it is along the side of the
right miter gauge groove and lock it. It
should be parallel to groove. If it i s not:
a. Unlock fence.
b. Loosen the four hex head screws
located to each side of the rip fenc e
handle.
c. Place the blade of the combination
square in the right miter gauge
groove as shown.
d. Slide the fence against the blade of
the combination square as shown.
Carefully lock the fence in this position.
e. Alternately tighten the hex head
screws.
f. Recheck alignment.
g. Repeat steps as needed until rip
fence is cor rectly aligned.
Combination Square
Miter Gauge Groove
Hex Head Screws
for Adjusting Fence
Parallelism
26
Page 27
Rip Fence Lock Lever Adjustment
The rip fence lock lever, when locked
down, should hold the rip fence securely.
The lever should not be dif ficult to push
down and lock.
To assure proper fence lock adjustment:
a. Raise lock lever and push fence
head toward rear of saw.
b. Hold fence head down onto front
guide bar while lift ing rear of fence up
and down.
c. Tighten adjusting nut until fence
clamp just barely touches r ear guide
bar.
d. This should provide the best fence
adjustment possible without over
tightening.
Adjustin g R i p In di c at or
1. Raise the blade up approximately 1".
2.Use a ruler to position the rip fence 6"
to the ri ght of the blade as shown. Loc k
the rip fence.
3.The rip indicator should read 6".
If not:
• Slightly loosen the Phillips head
screw.
• Slide the indicator left or right as
required.
• Tighten the Phillips head screw.
Adjusting
Nut
Fence
Clamp
Rear Gui de
Bar
Fence Clamp and Rear Guide Bar
Should Barely Touch When
Fence is Raised
Rip Indicator
6"
27
Page 28
Alignment (contin ue d)
Checking Sliding Table Extension
Lock the table ext ension lock lever. Pullpush on the sliding table extension. It
should not move.
WARNING: To reduce the risk of
thrown workpiece, do not use
with extension lock lever
unlocked.
If the sliding table extension moves
when locked:
1. Release the table extension lock lever.
2.Find the front hex coupling located
underneath the f ront table.
3.Loosen the hex locking nut.
4.Turn the hex coupling counterclockwise.
5.Lock the table extension lock . Pull-push
on the sli ding table extension. Readjust
hex coupling if necessary. Tighten the
hex locking nut aga inst coupling.
Installing Blade Guard
1. Locate the blade guard.
2.Two (2) locator pins are on the blade
guard. These lo cator pins fi t i nto matching holes on a bracket located on the
table saw trunnion.
3.Turn the blade guard locking knob
clockwise to securely attach the blade
guard in place.
Hex Locking
Nut
Front Hex
Coupling
28
Blade Guard
Locking Knob
Pin
Page 29
Aligning Blade Guard
IMPORTANT: To work properly, the
spreader must always be adjusted so the
cut workpiece will p ass on either side of
the spreader without binding or skewing
to the side.
NOTE: The spreader is thinner than the
width of the cut (kerf) by appr oximatel y six
thicknesses of paper .
1. Raise blade all the way up, making
sure it is square with tabl e.
2. Use a wrench to loosen the screw
that secures the spreader support to
the spreader mount.
3. Raise blade guard. Lift up both antikickback pawls. Insert a large set
screw wrench in the notches of the
pawls to hold the pawls out of the
way.
4. Place a square against the spreader
as shown. Use a wrench to tighten
the screw.
5. Make two folds i n a small piece (6 x 6
inch) of ordinary newspaper making
three thicknes ses.
The folded paper will be used as
“spacing gauge”.
6. Using 7/16 wrench loosen the 1/4-20
hex head screws so the spreader can
slide sideways.
7. Place rip fence on the right hand side
of table. Carefully move it against
blade so that i t is paralle l to the blade,
and just touches tips of saw teeth.
Tighten ri p fence lock lever.
8. Insert folded paper between spreader
and fence.
9. Hold spreader flat against folded
paper and fence. Tighten screws
using 7/16 inch wrench.
10. To remove blade guard and spreader,
loosen the blade guard locking knob.
Do not loosen other screws. This
allows you to remove and replace the
guard for non-through cuts without
disturbing the spreader alignment.
Spreader
1/4-20 Hex Head Screws
Combination
Square
Kerf
Folded
Paper
Screw
Wood
Blade
Paper
29
Page 30
Alignment (contin ue d)
Removi ng an d In stalli ng S awblade
WARNING: To reduce the risk of
injury from accidental start, turn
switch “OFF” and remov e plug
from power source outlet before
removing or installing sawblade.
a. Raise blade guard, remove insert,
elevate blade to its highest point.
b. To remove blade, hold arbor wrench
securely, pull arbor nut wrench
towards the front of the table.
c. To tighten arbor nut, hold arbor
wrench securely, push arbor nut
wrench towards the rear of the table.
When installing the blade, make sur e
the teeth are pointi ng toward the front
of the saw and that the blade and collars are clean, and fr ee from any burrs.
The hollow side of the collar must be
against the blade.
Always tighten the arbor nut secur ely.
NOTE: When using the dado or mold-
ing head, it is not necessary to instal l
the outer (loose) blade collar.
d. Lower the blade below the table.
e. To replace insert, place insert into
opening in table and push toward
rear of saw to engage rear spring on
insert and until key slot in insert will
drop over screw. Tighten screw. Do
not tighten screw to the point where it
will deflect the inser t.
WARNING: To reduce the risk of
injury from a thrown workpiece,
blade parts, or blade contact,
never operate saw without the
proper insert in place. Use the
sawblade insert when sawing.
Use the proper size dado/molding insert for dado blades and
molding heads.
Open End Arbor
Shaft Wren ch
Tighten
T op Teeth Pointing
to Front of Saw
Closed End
Arbor Nut
Wrench
Collar
Arbor Nut
Blade Insert
WARNING: For your own safety,
turn switch “OFF” and remove
plug from po we r so urce outlet
before making any adjustments.
30
Page 31
Miter Gauge Alignment
NOTE: The graduations are manufac-
tured to very close tolerances which provide ample accuracy for fine
woodworking. In some cas es where
extreme accuracy is required, when making angle cuts, for example, make a trial
cut and then recheck it.
There are adjustable screw stops for
the stop pin at 0° and 45° right and
left positions for conveniently setting
the miter gauge to cut miters at these
standard angles.
Adjusting Stop Screws
A. Loosen lock nut of screw for 0° stop.
B. Place 90° square against the miter
gauge bar and the face of the miter
gauge head.
C.If adjustment is needed loosen han-
dle of miter gauge. Adjust miter
gauge head flush to squ are. Tighten
lock knob.
D. Ad ju st stop sc re w un t il it re s ts
against the stop pin and tighten lock
nut.
E. Adjust 45°, left and right using a 45°
triangle or a protractor of a square
using the above procedure.
The miter gauge head should swivel
smoothly on the bar after the knob is loosened. To adjust this swivel movement:
A. Loosen the knob.
B. Loosen set screw with a 2.5mm hex
wrench.
C.If the head is too loose turn the fl at-
head screw in a clockwise direction.
If the head is too tight and wi ll not
swivel smoothly turn the flathead
screw counterclockwise.
D.Tighten set screw.
Bar
Knob
Adjustment
Screw
Flat Head
Screw
Set Screw
Miter Gauge
Head
Pointer
Stop Pin
31
Page 32
Alignment (contin ue d)
Marking the Ind-I-Cut:
a. With blade 90° (square to table) and
miter gauge in left groove, cross cut
a piece of wood holding the wood
firmly against miter gauge.
b. Pull miter gauge back until fres hly cut
edge of wood is over disk. Using a
sharp pencil, mark a line on disk at
freshly cut edge of wood.
c. With miter gauge in right hand
groove, follow same procedure and
mark another line on disk.
d. These lines indicate the “pat h” of the
cut (kerf) m ade by th e sawbl a de.
e. When cutting the workpiece, line up
mark on workpiece with line on disk.
NOTE: When the blade is changed, or a
dado/molding head i nstalled these lines
can be erased and reset.
Adjusting Bevel Lock
1. Release blade tilt lock l ever and bevel
blade to 45°.
2.Lock blade tilt lock lever, push in to dis-
engage the outer hub of the el evation/
bevel handwheel and wi th moderate
force attempt to move handwheel
toward the 0° bevel.
3.If blade tilt mechanism cannot be
moved, no additional adj ustme nt is necessary.
4.If blade tilt mechanism can be moved
adjust the blade tilt lock nut by rotating
clockwise 1/4 turn.
5.Repeat steps 3 and 4 as necessary.
6.Release hub of the elevation/bevel
handwheel and move blade ti lt mechanism back to 0°.
Marking
Ind-I-Cut
Using
Ind-I-Cut
Blade Tilt
Lock Nut
32
Page 33
Mounting Your Saw
Mounting T able Saw to Workbench
or Legse t
WARNING: To reduce the risk of
injury from accidental start,
make sure switch is "OFF" and
plug is not connected to power
source outlet.
WARNING: To reduce the risk of
injury from kickback or saw
movement the saw must be
properly secured to a sturdy
workbench, cabinet or legset.
Casters if provided on the cabinet or legset must be locked
during saw opera tion. If there is
any tendency for the saw to
move or rock during operation,
this must be corrected immediately.
If table saw is to be used in a permanent
location, it should be f astened securel y to
a firm supporting surf ace such as a workbench, or legset using t he mou nting
holes.
Workben ch M ounting Using
Hardware
When mounting ta bl e saw to a wor kbench
and using a vacuum hookup, holes should
be drilled through t he supporting surface
of the workbench using the dimensions
illustrated.
If a vacuum is not used, an opening must
be made in the workbench using the
dimensions illustrated, so the sawdust
can fall away from the saw base area .
Table Saw Mounting Procedures
1. Locate the proper hole mounting diagram for your desired type of table saw
mounting.
2.Mark the hole locations and cutout
opening if vacuum is not used. Drill the
holes and cut o ut t he area to allow sawdust to fall away fro m the base if a vacuum is not being utilized.
Workbench Surface
4"
16-3/4"
3/8"
15-5/16"
21-5/16"
3"
Diagram of Workbench Mounting Holes
3.Place the tabl e saw on the mounting
surface and al ign the four holes.
4.Insert four (4) 1/4-20 screws that are
long enough for washers and nuts
which will proper ly se cure t he t able saw
to the mounting surface.
NOTE: Mounting hardware (bolts, nuts,
washers etc.) are not supplied with the
saw.
Opening if
Vacuum
is not used
23-3/4"
(Front of Table Saw)
Dia.
33
Page 34
Mounting Your Saw (continued)
Mounting Table Saw to RIDGID
Universal Power Tool Legset
#AC9910
1. Assemble legset per instructions.
2.Locate the four (4 ) “TS” lay out point s on
the particle board tables.
3.Drill the four (4) above holes.
4.Insert four (4) 1/4-20 screws t hat are
long enough for washer s and nuts
which will pr operly secure the t able s aw
to the legset. Tighten hardware.
NOTE: Mounting hardware (bolts, nuts,
washers, etc.) are not supplied with the
saw.
Workben ch M ounting Using "C "
Clamps
An alternative method of securing your
table saw is to fasten the saw base with
"C" clamps.
1. Follow instructions for mounting to
workbench, substitute "C" clamps at
each mounting screw loc ation.
2.Securely clamp saw to workbench
using four "C" clamps, as shown.
Supporting surface where saw is to be
mounted should be examined carefully
after mounti ng to i nsure that no movement can occur during use. If any tip ping,
sliding or walking is noted, secure the
workbench or cabinet befor e operating
the table saw.
Mounting
Screw Location
"C" Clamps
(Front and Rear)
Diagram of Clamping Table Saw
to Workbe n c h
"C" Cl a m p
Supporting Table Saw with
Sawhorses
The table saw has provisions for being
supported by sawhorses. The sawhorse
can be built with the 2" x 4"crosspieces
either vertical or horizontal . Make sure the
sawhorses ar e secure. Holes for securing
unit to sawhorse(s) ar e provided.
34
Page 35
Safety Instructions for Basic Saw Operations
Before Each Use
Inspect your saw.
• To reduce the risk of injury from
accidental starting, turn the switch
off, unplug the saw, and remove
the switch key before raising or
removing the guard, changing the
cutting tool, changing the se tup, or
adjusting anything.
• Check for alignment of moving
parts, binding of moving parts,
breakage of parts, saw stability,
and any other conditions that may
affect the way the saw works.
• If any part is missing, bent or broken in any way, or any electrical
part does not work properly, turn
the saw off and unplug the saw.
T o Reduce the Risk of Injury From Jams, Slips Or Thrown Pieces
(Kickbacks Or Throwbacks)
Inspect Your Blade.
• Choose the right blade or cutting
accessory for the material and the
type of cutting you plan to do.
• Never use grinding wheels, abrasive cutoff wheels, friction wheels
(metal cutting blades) wire wheels
or buffing wheels. They can fly
apart explosively.
• Cut on ly wood, wood like or plastic
materials. Do not cut metal.
• Choose and inspect your cutting
tool carefully:
- To reduce the risk of cutting tool
failure and thrown shrapnel (broken pieces of blade), use only 10”
or smaller blades or other cutting
tools marked for speeds of 5000
rpm or higher.
- Always use unbroken, balanced
blades designed to fit this saw’s
5/8 inch arbor.
• Replace dama ged or missin g parts
before using the saw again.
• Use the sawblade guard, s preader
and anti-kickback pawls for any
thru-sawing (whenever the blade
comes through the top of t he workpiece). Make sure the anti-kickback
pawls work properly. Make sure the
spreader is in line with sawblade.
• Remove adjusting keys and
wrenches. Form a habit of checking for and removing keys and
wrenches from table top before
turning saw on.
• Make sure all clamps and locks are
tight and no parts have excessive
play.
- When thru-sawing (making cuts
where the blade comes through
the workpiece top), always use a
10 inch diameter blade. This
keeps the spreader in closest to
the blade.
- Do not over tighten arbor nut.
Use arbor wrenches to “snug” it
securely.
- Use only sharp blades with properly set teeth. Consult a professional blade sharpener when in
doubt.
- Keep blades clean of gum and
resin.
- Never use the saw without the
proper blade insert.
Inspect your work area.
• Keep work area clean.
• Cluttered areas and benches invite
accidents. Floor must not be slippery from wax or sawdust.
35
Page 36
Safety Instructions for Basic Saw Operations (continued)
• To reduce the risk of burns or other
fire damage, never use the saw
near flammable liquids, vapors or
gases.
• T o reduce the risk of in jury, don’t do
layout, assembly, or setup work on
the table while blade is spinning. It
could cut or throw anythin g hitting
the blade.
Plan your work
• Use the right tool. Don’t force tool
or attachment to do a job it was not
designed for.
Inspect your workpiece.
• Make sure there are no nails or foreign objects in the part of the workpiece to be cut.
• When cutting irregularly shaped
workpieces, plan your work so it
will not slip and pinch the blade:
• A piece of molding for example,
must lie flat or be held by a fixture
of jig that will not let i t twist, roc k or
slip while being cut. Use j igs or fixtures where needed to prevent
workpiece shifting.
• Use a different, better suited type
of tool for work that can’t be made
stable.
Plan your cut.
• To reduce the risk of kickbacks and
throwbacks which occur when a
part or all of the workpiece binds on
the blade and is thrown violently
back toward the front of the saw:
- Never cut Freehand. Always use
either a rip fence, miter gau ge or
fixture to position and guide the
work, so it won’t twist or bind on
the blade and kickback.
- Make sure there’s no debris
between the workpiece and its
supports.
• Use extra caution with large, very
small or awkward workpieces.
• Use extra supports (tables, saw
horses, blocks, etc.) for any workpieces large enough to tip when
not held down to the table top.
Never use another person as a
substitute for a table extension, or
as additional support for a workpiece that is longer or wider than
the basic saw table, or to help feed,
support or pull the workpiece.
• Never confine the piece being cut
off, that is, the piece not against the
fence, miter gauge or fixture. Never
hold it, clamp it, touch it, or use
length stops against it. It must be
free to move. If confined, it could
get wedged against the blade and
cause a kickback or throwback.
• Never cut more than one workpiece at a time.
• Never turn your table saw “ON”
before clearing everything except
the workpiece and related support
devices off the table.
Plan Ahead To Protect Your Eyes, Hands, Face and Ears
Dress for safety
• Do not wear lo ose c lothing, glo ves,
neckties or jewelry (rings, wrist
watches). They can get caught and
draw you into moving parts.
• Wear nonslip footwear.
• T i e back long hair.
• Roll long sleeves above the elbow.
• Noise levels vary widely. To reduce
the risk of possible hearing damage, wear ear plugs or muffs when
using table saw for hours at a time.
36
Page 37
• Any power saw can throw foreign
objects into the eyes. This can
result in permanent eye damage.
Always wear safety goggles, not
glasses, complying with ANSI
Z87.1 (or in Canada CSA Z94.3-
99) shown on package. Everyday
eyeglasses have only impact resistant lenses. They are not safety
glasses. Safety goggles are available at many local retail stores.
Glasses or goggles not in compliance with ANSI or CSA could seriously hurt you when they break.
• For d usty operations, w ear a dust
mask along with safety goggles.
Plan the way you will push the
workpiece through.
• Never pull the workpiece
through. Start and finish the cut
from the front of the table saw.
• Never pu t your fingers or handsin the path of the sawblade or
other cutting tool.
• Never reach in back of t he cutting
tool with either hand to hold down
or support the workpiece, to
remove wood scraps, or for any
other reason.
• Avoid hand positions wh ere a sudden slip could cause fingers or a
hand to move into a sawblade or
other cutting tool.
• Don’ t overreach. Always k eep good
footing and balance.
• Push the workpiece against the
rotation of the blade, never feed
material into the cutting tool from
the rear of the saw.
• Always push t he workpiece all the
way past the sawblade.
• As much as possible, keep your
face and body to one side of the
sawblade, out of line with a possible kickback or throwback.
• Set the cutting tool as low as possible for the cut you’re planning.
Reduce the Risk of Accidental
Starting.
• Make sure switch is “OFF” before
plugging saw into a power outlet.
Whenever Sawblade Is Spinning
WARNING: Don't allow familiarity (gained from frequent use of
your table saw) cause a careless
mistake. Always remember that
a careless fraction of a second
is enough to cause a severe
injury.
• Before actually cutting with the
saw, watch it while it runs for a
short while. If it makes an unfamiliar noise or vibrates a lot, stop
immediately. Turn the saw off.
Unplug the saw. Do not restart until
finding and correcting the problem.
• Make sure the top of the arbor or
cutting tool turns toward the front of
the saw.
Keep Children Away.
• Keep all visitors a safe distance
from the table saw.
• Make sure bystanders are clear of
the table saw and workpiece.
Don’t Forc e Tool.
• Let the blade reach full speed
before cutting.
• It will do the job better an d safer at
its designed rate.
37
Page 38
Safety Instructions for Basic Saw Operations (continued)
• Feed the workpiece into the saw
only fast enough to let the blade
cut without bo gging down or binding.
Before freeing jammed material.
• Turn switch “OFF”.
• Wait for all moving parts to stop.
• Unplug the saw.
• Check blade, spreader and fence
for proper alignment before starting
again.
• To reduce the risk of throwb ack
of cut off pieces.
• Use the guard assembly.
T o remove loose pieces beneath or
trapped inside the guard.
• T urn saw “OFF ”.
• Remove switch key.
• Wait for blade to stop before lifting
the guard.
Before Leaving The Saw.
• Turn the saw off.
• Wait for blade to stop spinning.
• Unplug the saw.
• Make workshop child-proof. Lock
the shop. Disconnect master
switches. Remove the yellow
switch key. Store it aw ay from children and others not qualified to use
the tool.
Work Feed Device s
Before cutting any wood on your saw,
study all of the “Basic Saw Operations”.
As you learn new table saw woodworking
techniques, you’ll see that many type s of
cuts need di fferent support and feeding
devices, known as ji gs or fixtures. They
can help you make cuts more accurately.
By helping to steady the work piece and
keep you away from the blade, they can
help you safely use your saw for certain
cuts.
Many people custom build their own jigs
and fixture s. Jigs and fixtures ar e often
designed for a particular cut.
You can use your table saw to easily
make many jigs and fixtures. To get you
started, we’ve included instr uctions for
some simple ones. Af ter you have made a
few practi c e cu ts , ma ke u p th e s e jigs
before starting any projects. The use of
these devices is explained in “Basic Saw
Operations” section.
38
Page 39
Push Stick
Make the push stick fr om a piece of solid
wood. Use a piece of 1 x 2 (3/4" x 1-5/8"
actual) by 15" long.
Slightly Less Than Thickness
Of Workpiece Up to 3/8"
Make the featherb oard from a piece of 8”
x 24” x 3/4” thick solid wood
24"
Kerfs About
5/16" Apart
Grain
8"
90° Notch
Push Block (For Use with Auxiliary
Fence)
There are any number of ways to properly
cut your workpieces to make a push
block. The following steps describe one
way you can make a push block.
Making the base:
• Start with a piece of 3/8 inch plywood
at least 5-5/8 i nches wide or wider and
12 inches long or longer.
• Make two ripcuts. Perform the first
ripcut along the side of the 3/8" wide
strip. Next, ripcut the 3/8" plywood to a
width of 5-1/8".
• Crosscut the 3/8" plywood to 12" long.
• Crosscut a 2-1/2" piece off the 3/8"
wide by 3/8" thick strip and save this
short piece for later.
The next cut s will creat e the 3/8 " by 9 -1/2"
notch in the base. Mark the long edge of
the board 2-1/2" from one end. Ma ke a
crosscut into the edge on the mark, stopping about 3/4" into the board. Set the
saw and rip the width to 4-3/4" along the
same edge as the stopped crosscut. Stop
the ripcut where the two cuts intersect.
Turn off the saw and remove the base
piece. The base should now measure as
shown.
Material for Push Bl o c k
At Leas t 12"
4-1/2"
3/8" Thick Plywood
5"
At Leas t 12"
Handle
Cutting Out the Base
2-1/2" (save)
4th Cut
1st Cut
2nd Cut
12"
Creating the Notch
1st Cut
2nd Cut
2-1/2"
Finished Base
12"
At Least
5-5/8"
2-1/2"
3/8"
4-3/4"
3rd Cut
At Least
5-5/8"
3/8"
5-1/8"
4-3/4"
These Edges
Must Be
Parallel
3/8" T hick Plywood
Base
At Least
5-5/8"
39
Page 40
Work Feed Devices (continued)
Making the handle:
• Miter crosscut a piece of 3/4 inch thick
plywood to shape and size sho w n:
NOTE: The mitered corners can be any
size that looks like the drawing (about 1-1/2"
by 1-1/2").
Putting it Together
• Using good quality woodworking glue,
glue the 3/8" x 3/8" x 2-1/2" piece strip
saved earlier to the base as shown.
IMPORTANT: Do not use nails or screws.
This is to prevent dulling of the sawblade
in the event you cut into the push block.
• Position the handle at the center of the
plywood base as shown. Fasten them
together with glue and wood sc rews.
IMPORTANT: Make sure the screw heads
do not stick out from the bottom of the
base, they mu st be flush or recessed. The
bottom must be flat and smooth enough
to slide along the auxiliary fence you are
now ready to make.
Auxiliary Fence
Making the base:
• Start with a piece of 3/8 inch plywood
at least 5-1/2 i nches wide or wider and
25-1 /2 inch es long or longe r.
• Cut the piece to shape and size shown:
Making the side:
• Start with a p i ece of 3 / 4 inc h pl y wood at
least 3 i nche s wi de or w ide r and 2 5-1 /2
inches long or longer.
• Cut the piece to shape and size shown:
• Optional: Drill three (3) holes in plyw ood
side similar to rip fence wood facing (see
page 31). The plywo od s ide ma y ei the r b e
mounted to the rip fence using these thre e
holes and appropriate nuts and bolts or
clamped to th e fence with “ C” cla mps .
Putting it together:
• Put the pieces together , as shown:
IMPORTANT: Make sure the screw heads
do not stick out from the bottom of the
base, they mu st be flush or recessed. The
bottom must be flat and smooth enough
to rest on the saw table without rocking.
40
3/4" Plywood Handle
3/8" Plywood Base
Glue
Only
Screw Head Must Be
Flush Or Recessed
Cutting Out the Base
25-1/2"
3/8" Thick Plywood Base
Cutting Out the Side
25-1/2"
3/4" Thick Plywood Side
Finished Auxil iar y Fence
4-3/4"
3/8"
Plywood
This face and this edge
must be parallel
5-1/2"
3"
3/4" Plyw ood
Page 41
Fence Facing
Select a piece of smooth straight wood
approximately 3/4 inch thick, and the
same length as the rip fence.
Attach it t o the f enc e with the three squ are
head bolts, nuts and washers. (See
“Hardware for Attac hing Wood Fac in g”) in
Repair Parts Figure 4. To remove the facing, loosen the hex nuts, slide the facing
toward the rear and out of the f ence slot.
If the fence facing is for use with feather
boards, it will need to be abou t 8" tall. For
use with molding heads and dado blades
the width should be at least 3".
3"
Minimum
1-3/8
3/4"
Counterbore
3/4 Diameter
x 3/8 Deep
9/32
Diameter
Hole
Fence
Square Head
Bolt
Flat
Washer
Hex
Nut
Lockwasher
Wood Facing
41
Page 42
Basic Saw Operations
Using the Miter Gauge
The miter gauge is used when crosscutting, miter cutting, bevel cutting, compound miter cutting, dadoing and when
rabbeting across the end of a narrow
workpiece.
WARNING: For your own safety,
always observe the following
safety precautions in addition to
the safety instructions of pages 3
thru 9 and 35 thru 38.
Additional Safety Instructions for
Crosscutting
Before Starting:
•Never use the rip fen ce when crosscut-
ting except as specifically inst ructed.
Crosscutting
Definition: A cutti ng or shaping operati on
made across the width of a workpiece.
The graduations on the miter gauge provide ample accuracy for average woodworking. In some cases where extreme
accuracy is requi red, make a trial cut and
then recheck it with a prec ision square, or
protractor.
NOTE: The space between the miter
gauge bar and the groove in the table is
held to a minimum during manuf acturing.
For maximum accuracy when using the
miter gauge, always favor one side of the
groove in the table. In other words, don’t
move the miter gauge from si de to side
while cutting but keep one side of the bar
riding against one side of the groove.
NOTE: Gluing a piece of sandpaper to the
face of the miter gauge head can help
prevent the workpiece from “creeping”
while it is being cut.
The miter gauge head is locked in position by twisting the lock knob clockwise.
Always tighten it secu rely when in use.
WARNING: To reduce the risk of
blade contact or kickback, hold
miter gau ge properly.
•An auxiliary wood facing att ached to the
miter gauge can help prevent workpiece twisting an d thr owbacks. Attac h it
to the slots provided. Make the facing
long enough and big enough to support
your work. Make sure, however, it will
not interfere with the sawblade guard.
•Use jigs or fixtures to help hold any
piece too small to extend across t he fu ll
length of the miter gauge face during
the cut. This let s you properly hold the
miter gauge and workpiece and helps
keep your hands away from the blade.
While cu tting:
•To r educe the risk of blad e contact,
always hold the miter gauge as shown
in the this section.
The miter gauge may be used in either of
the grooves in the table.
When using the miter gauge in the left
hand groove, hold the workpiece firmly
against miter gauge head with your left
hand, and grip the lock knob with your
right hand.
When using the miter gauge in the right
hand groove, hold the workpiece with
your right hand and the lock knob with
your left hand.
Always Support
Sandpaper
Long Workpieces
42
Page 43
Crosscutting (continued)
Slots are provided in the miter gauge for
attaching an auxiliary facing to make it
easier to cut very long or short pieces.
Select a suitable piece of smooth wood,
drill two ho l es th rough it and attach with
screws. Make sure the f acing does not
interfere with the proper operation of the
sawblade guard.
When cutting long workpieces, you can
make a simple support by clamping a
piece of pl ywood to a sawhorse. (As seen
on previous page. )
Repetitive Crosscutting
Definition: Cutti ng a quanti ty of pieces the
same length without having to mark each
piece.
•Follow all safety precautions and operational instructions for cross cutting.
•When making repet itive cuts from a
long workpiece, ma ke sure it is adequately supported.
WARNING: Never use the rip
fence as a direct length stop
because the cutoff piece could
bind between the fence and the
blade causing a kickback.
•When making repetitive cuts sho rter
than 6 inches, clamp a bl ock o f wood 3”
long to the fence. Plac e fence at
desired posit ion to act as a length stop.
•Slide the workpiece along the miter
gauge until it touches the block... hold
the workpiece sec urel y against the
miter gauge.
•Make the cut...turn the saw off...remove
the piece aft er the blade has stopped
and before cutting the next piece.
WARNING: To reduce the risk of
kickback from twisting the workpiece, when clamping the b lock
make sure that the end of the
block is well in front of the sawblade. Be sure it is clamped
securely.
Lock
Knob
Stop P i n
Miter Gauge
Head
45° Stop
Screw
“C” Clamp
Cut Off Piece
Auxiliary
Facing
Wood Block
43
Page 44
Basic Saw Operations (continued)
Miter Crosscutting
Miter cutting is cutting wood at an angle
other than 90° with the edge of the wood.
Follow the same procedure as you would
for crosscutting.
•Adjust the mite r gauge to the desired
angle, and lock i t.
•The miter gauge may be used in either
of the grooves in the table. Make sure it
is locked.
•When using the miter gauge in the left
hand groove, hold the workpiece firmly
against the miter gauge head with your
left hand, and grip the lock knob with
your right hand.
•When using the miter gaug e in the ri ght
hand groove, hold the workpiece with
your right hand and the lock knob with
your left hand.
Bevel Crosscutting
Bevel crosscutting is the same as cro sscutting except that the wood is cut at an
angle...other than 90° with the bottom flat
side of the wood.
•Adjust the blade to the desired angle.
•Always use the miter gauge in the
groove to the right of the blade. It cannot be used in the groove to the left
because the blade guar d wil l interfere.
Hold the workpiece with yo ur r ight h and
and the lock knob with your left hand.
•Use the auxiliary fence/work suppo rt for
additional support of the workpiece.
Compo und Crosscutti ng
Compound cutting is a combination of
miter cutting and bevel crosscutting. The
cut is made at an angle other than 90° to
both the edge and the bottom flat side of
the wood.
•Adjust the mite r gauge and the blade to
the desired angl e...Make sure miter
gauge is locked.
44
Page 45
Using the Rip Fence
Ripping, bevel ripp ing, resawing and rabbeting are performed using the rip fence
together with the auxi li ary fence/work
support, push stick or push block.
WARNING: For your own safety,
read and always observe all
safety precautions listed in manual and on saw.
Additional Safety Instructions for
Rip Cuts
•Never use the miter gauge when ripping
•Use a push stick whenever the fence is
2 or more inches from the blade.
•When thru sawing , use an auxiliary
fence and push block whenever the rip
cut is between 1/2 and 2 inches from
the blade.
•Never thru saw rip cuts narrower than
1/2 inch.
•Never rip anything shorter than 10”
long.
•When using a push stick or push block,
the trailing end of the workpiece must
be square. A push stic k or block again st
an uneven end could sli p off or push the
workpiece away from the f ence.
•A featherboard can help guide the
workpiece. (See “Basic Saw OperationUsing Featherboar ds for Thru Sawing”
section.)
•Always use featherboards for any nonthru sawing rip type cuts. (See “Basic
Saw Operations-Using Featherboards
for Non-thru sawing” section)
Before Starting:
•To reduce the risk of kickbacks and
slips into the blade, make sure the rip
fence is parallel to the sawblade.
•Befo r e t h r u sa wing, check th e a nti-ki ckback pawls. the pawls must stop a kickback once it has started. Replace or
sharpen anti-kickback pawls when
points become dull.
•Plastic and composition (like hardboard) materials m ay be cut on your
saw. However, since these are usually
quite hard and slippery, the anti-kickback pawls may not stop a ki ckback.
Therefore, be espe cially caref ul in your
setup and cuttin g procedures.
While Thru sawing:
•To reduce the risk of kickbacks and
slips into the bl ade, always push forward on the section of the workpiece
between the sawblade and the rip
fence. Never push f orward on th e piece
being cut off .
45
Page 46
Basic Saw Operations (continued)
Ripping
Definition: Cutti ng operation along the
length of the workpiece.
Position the fence to the desired width of
rip and lock in place.
Befor e starting to rip, be s ur e :
1. Rip fence is parallel to sawblade.
2. Spreader is properly aligned with sawblade.
3.Anti-kickback pawls are functioning
properly.
When ripping l ong b oards or lar ge p anels,
always use a work support. A simpl e support can be made by clamping a pie ce of
plywood to a sawhorse.
WARNING: To reduce the risk of
kickback, push forward only on
the part of the workpiece that
will pass between th e blade and
the fence.
Keep your hands out of the blade path.
Feed the workpiece by pushing forward
only on the part of the work piece that will
pass between the blade and the fence.
Stop your l eft thumb at the fr ont edge of
the table. Finis h the cut with the appropriate pusher.
Feed
Force
Blade
Path
Use the micro-adjus t mechan ism to make
fine adjustment s to t he rip f ence. To move
the rip fence push in on the m icro-adjust
knob and rotate.
Once the trailing end is on the table:
When “width of rip” is 2" or wider, use the
push stick to push the work al l the way
past the blade.
Push Stick
46
Page 47
Ripping ( continued)
When “width o f rip” is na rrower than 2 " th e
push stick cannot be used because the
guard will interfere...use the auxi li ary
fence and push block.
Attach auxi liary f enc e to r ip fe nce wit h tw o
“C” clamps or use “T” slot and hardware.
Auxiliary
Fence
“C” Clamp
Feed the workpiece by hand along the
auxiliary fence until the end is approx imately 1" past the fr ont edge of the table.
Continue to feed using the push block.
Hold the workpiece in posi tion and install
the push block by sli ding it on top of the
auxiliary fence/work support (this may
raise guard).
WARNING: To reduce the risk of
injury from blade contact never
thru saw cuts narrower than 1/2"
wide.
Narrow strips thi cker than the auxiliary
fence/work support may enter the guard
and strike the baff le. Car efully r ai se guard
only enough to clear the workpiece. Use
push block to complete cut.
Workpiece
Baffle
Push Block
Auxiliary Fence
Bevel Ripping Narrow Work
When bevel ripping material 6” or narrower, use fence on the right side of the
blade only. This will provide more space
between the fence and the sawblade for
use of a push stick. If the fence is
mounted to the left, the sawbla d e gua r d
may interfere with pr oper use of a push
stick.
47
Page 48
Basic Saw Operations (continued)
Using Featherboards for Thru
Sawing
Featherboards ar e not employed for thru
sawing operations when using the miter
gauge.
Featherboards ar e used to keep the work
in contact with the fence and table as
shown, and to help stop kickbacks.
Add a 7-1/2” high flat facing board to the
fence, the f ull length of the fence. The facing board may either be “C”-clamped to
the rip fence or held in place with appropriate nuts and bolt s (see “Work feed
Devices” secti on).
Mount featherboar ds to facing board and
table as shown, so that leading edges of
featherboards wil l support workpiece.
WARNING: Make sure the featherboard against the edge
presses only on the uncut portion (in front of the blade). It
might otherwise pinch the blade
in the kerf and cause a kickback.
Before starting the operation (switc h
“OFF” and blade below table surface):
1. Install featherboards so they exert
pressure on the workpiece; be positive
they are securely att ached.
2.Make sure by trial that the featherboards will stop a kickback if one
should occur.
Work
Support
Featherboard
Featherboard
“C” Clamps
Facing
Board
Workpiece
Push
Stick
48
Page 49
Using Featherboards for Non-Thru
Sawing
Featherboards ar e not employed during
non-thru sawing operations when using
the miter gauge.
Use featherboards for all other non-thru
sawing operations (whe n sawbl ade guard
must be removed). Featherboards are
used to keep the work in contact with the
fence and table as shown and to stop
kickbacks.
Add a 7-1/2” high flat facing board to the
fence, the full len gth of the fence.
Mount featherboar ds to facing board and
table as shown, so that leading edges of
featherboards will support workpiece until
cut is complete, and the workpiece has
been pushed completely past the cutter
(sawblade, dado-head, etc.) with a push
stick, as in rippi ng.
Before starting the operation (make sure
the switch is in the of f position and the
blade is below the tabl e):
1. Install featherboards so they exert
pressure on the workpiece; be positive
they are secure.
2.Make sure and try out the set-up to verify that the featherboards are correctly
positioned.
WARNING: For your own safety,
replace the sawblade guard as
soon as the non-thru sawing
operation is complete.
Work Support
“C” Clamp
Featherboard
Featherboard
“C”
Clamp
Facing
Board
Push Stick
49
Page 50
Basic Saw Operations (continued)
Resawing
Resawing is a rip cut made in a piece of
wood through its thickness. The piece is
typically posit ioned on its edge. If the
piece is narrower than 3- 3/8" it can be
resawn in one pass with the blade guard
in place. Extra supports or fixtures will be
required when the edge resti ng on the
table is too narrow for the piece to be stable or when the fence interferes with the
blade guard. (See method described
below)
WARNING: Do not attempt to
resaw bowed or warped material.
It can’t be properly supported. It
could kickback or bind.
NOTE: To resaw a piece of wood wider
than 3-3/8”, or a piece nee ding extra support, it will be necessary to remove the
blade guard and use the auxi li ary fence/
work support. (See “W orkfeed Devices”.)
Construct an auxiliary fence/work support
as shown. Depending on the thickness of
the workpiece the widt h of the auxiliary
fence/work support will have to be made
so that it can be attached to the t able saw
top with “C” clamps. Clamp the auxi liary
fence/work sup port t o the tabl e so that the
workpiece will sl ide easily without bi nding
between the two fences and it wi ll not t il t
or move sideways.
Auxiliary Fence/
Work Support
WARNING: For your own safety
1. Do not “Backup” (reverse
2. Make first pass to a depth
3. Keeping the same face of
WARNING: For your own safety,
install blade guard immediately
upon completion of the resawing operatio n.
Workpiece
feeding) while resawing
because this could cause a
kickback.
slightly more than one half the
width of the board.
board against the fence rotate
it end over end and mak e the
second pass.
Using Carbide Tipped Blades
WARNING: To reduce the risk of
cutting tool failure and thrown
shrapnel (broken pieces of
blade) read and understand all
the warnings and instructions
which come w ith carbide tipped
blades. Failure to heed all carbide tipped blade warnings and
safety instructions c an result in
serious injury.
Carbide is a very hard but brittle material.
Take care when mounting, using and storing carbide blades to prevent accidental
damage. Slight shocks, such as striking a
tip during handli ng, can s erious ly damage
the blade. Foreign objects in the work piece, such as wir e or nails, can also
cause tips to cr a ck or br ea k off.
Before using a car bide tipped blade,
always examine the blade and tips for
damage. Look for bent teeth, a bent
blade, cracks, broken, missing or loose
carbide tips. Do not use a carbide tipped
blade if damage is found or suspected.
Do not use a carbide tipped blade without
all appropr iat e guards in place.
Mount blade securely in proper rotation
direction.
Never rotate a carbide tipped blade faster
than its maximum recommended speed.
50
Page 51
Dadoing
Dadoing is cutting a groo ve int o the workpiece. There are a wide variety of dado
heads available - be sure and consult the
specific instr uctions included with your
dado head.
WARNING: For your own safety;
always read, understand and follow all directi ons in the instructional book l et furnished with the
dado head.
The slot provided for the saw blade in the
regular table insert is too small for t he
dado head to pass through. Therefore, a
special dado inser t must be purchased.
WARNING: For your own safety,
always use dado insert listed
under recomm end ed acces sories.
A dado is never used for thru sawing or
cutting compl etely through a workpiece. It
is used for non-thru sawing, cutting par t
way into the workpiece. Therefore, the
blade guard and spr eader c annot be used
and must be removed. Use caution. Use
miter gauge, rip fence, featherboards,
push sticks, or fence facing board as
required.
WARNING: For your own safety,
always replace the blade, table
insert, guard and spreader when
you are finished dadoing.
The dado head is assemb led to the saw
arbor in the same manner as the saw
blade. The arbor on the saw, is long
enough so that the widest cut that can be
made is 13/16" wide. It is no t neces sar y to
instal l the outside loose col lar before
screwing on the arbor nut. Make sure the
arbor nut is tight.
When cutting a “deep ” dado or a wide
groove it is nec essary to remove only a
small amount of mater ial (1/8"-1/4" ) at a
time. Contin ue to increase dado eleva tion
until the desired depth is reached.
Dado
Insert
Saw
Arbor
51
Page 52
Basic Saw Operations (continued)
Rabbeting
Rabbeting is known as cutting out a section of the corner of a piece of material,
across an end or along an edge.
To make a rabbet requires cuts which do
not go all the way through the material.
Therefore, the blade guard must be
removed.
1. Remove blade guard.
2.For rabbeting along an edge (long way
of workpiece) as shown add facing to
rip fence approximately as high as the
workpiece is wide. Adjust rip fence and
blade to required dimensions; then
make first cut with board flat on table as
any rip (t ype) cut; make second cut with
workpiece on edge. Follow all precautions, safety instructions, and operational instructions as for ripping, or rip
type operations, including featherboards and push stick, etc.
3. For rabbeting across an end, for workpiece 10-1/2” and narrower, make the
rabbet cut with the board flat on the
table. Using the miter gauge fitted with
a facing, follow the same procedures
and instructions for cross cutting making successive cuts across the width of
the workpiece to obtain the desired
width of c ut. Do not use the rip fence fo r
rabbeting acr oss the end.
WARNING: For your own safety,
install blade guard immediately
upon com pletion of rab beting
operation.
Some rabbet cuts can also be made in
one pass of the workpi ece over the cutter
using a dado head.
Rabbet
Second
Cut Etc.
First
Cut
This Side
Against Fence
When Making
Second Cut
Second Cut
First Cut
Rabbet
Ploughing and Molding
Ploughing is grooving with the grain the
long way of the workpiece, us ing the
fence. Use featherboards and push sticks
as required.
Ploughing
52
Page 53
Molding
Molding is cutting a shape on the edge or
face of the workpiece. With a mo ldi ng
head and a selection of different knif e
shapes it i s possi ble f or almost a ny ki nd of
molding (base, cove, bead, etc.) to be
produced.
There are a wi de vari ety o f mol ding heads
available as well as many different
shapes of knives. Be sure and con sul t the
specific instr uctions included with your
molding head.
WARNING: For your own safety;
always read, understand, and follow all directi ons in the instructional book l et furnished with the
molding head.
The slot provided for t he sawblade in the
regular table insert is too small for t he
molding head to pass through. Therefore,
a special dado/mol ding insert must be
purchased.
WARNING: For your own safety,
always use molding insert listed
under recomm end ed acces sories.
When using the molding head i t will be
necessary to remove t he blade guar d and
spreader. Use caution. Use miter gauge,
fence, featherboar ds, push st icks or fence
facing board, et c., as required.
WARNING: For your own safety,
always replace the blade, table
insert, guard and spreader when
you are finished molding.
A typical molding head i s shown, The various shapes of knives are fitted into
grooves in the cutterhead and secured
with a screw(s).
The molding head is assembl ed to t he
saw arbor in the sa me manner as th e saw
blade. It is not nece ssary to install the outside loose collar bef ore screwing on the
arbor nut. Make sure the arbor nut is tight.
It is necessar y to use an auxiliary fenc e
when shaping edges of a work piece.
Position th e auxiliary fence over the cutterhead with the cutter head below the
surface of th e saw tabl e. Turn the saw
“ON” and slowl y rais e the cut terhead . The
cutterhead will then cut its own groove in
the auxiliary fence.
Molding
Auxiliary Fence
53
Page 54
Maintaining Your Table Saw
Maintenance
WARNING: For your own safety,
turn switch “OFF” and remove
plug from po we r so urce outlet
before maintaining or lubricating
your saw.
•Do not allow sawdust to accum ulate
inside the saw. Frequently blow out any
dust that may accum ulate inside the
saw cabinet and the motor.
•Clean your cutt ing too ls with a gum and
pitch remover.
•The cord and the tool should be wiped
with a dry clean cloth to prevent deterioration from oil and grease.
•A coat of furni tur e paste wax applied to
the table will help to keep the surface
clean and al low workpieces to slide
more freely.
•If the power cord is worn, cut, or damaged in any way, have it replaced
immediately.
Anti-Kickback Pawls
Make sure the teeth of the anti-kickback
pawls are alway s sharp. To sharpen:
1. Remove blade guard.
2.Rotate pawl toward rear of spreader so
that teeth are above top of spreader .
Anti-Kickback
Pawl
Spreader
Round
File
Teeth
3. Hold spreader with left hand and place
pawl over corner of workbench as
shown.
4. Using a small round file (smooth cut)
sharpen the t eeth.
5.Reinstall blade gu a rd.
Adjusting N y lon Set Sc rew
If the sawblade has a very slight amount
of lateral move ment (lef t-right movem ent),
or if the sawbl ade is e levate d and tends to
lower itself sl ightly, the nylon set screw
needs to be tightened.
1. Bevel the sawblade to 45°.
2.Locate the 10-32 x 3/4 nylon set screw
and nut. Reference service key #27 &
28 page 48. See illustration.
WARNING: For your own protection, turn switch “OFF” and always
remove pl ug fr om power source ou tlet bef o re tr ou bl e shooting.
General
T roubleProbable CauseRemedy
Excessive
Vibration
Cannot make
square cut when
crosscutting.
Cut binds, burns
or stalls motor
when ripping.
Cut not true at
90° or 45° bevel
positions.
Elevating hand wheel turns
hard.
1. Blade out of balance or
damaged
1. Miter gauge not
adjusted properly.
1. Dull blade or improp er
tooth set.
2. Blade is heeling.
3. Warp ed board
4. Rip fence not parallel
to blade.
5. Sp reader out of align-
ment.
1. Indexes not properly
adjusted.
1. Sawdust on threads of
elevating scr ew.
1. Replace blade.
1. See “Adjustment s” section “Miter
Gauge.”
1. Sharpen or replace blade.
2. See “Alignment ” sect ion, “Heeling
Adjustment”.
3. Make sure concave or hollow side is
facing “down” feed slowly.
4. See “Alignment ” section, “Align ing
Rip Fence.”
5. See “Alignment ” section, “Inst alling
Blade Guard.”
1. See “Alignment ” sect ion, “Blade Tilt,
or Squareness of Blade to Table”.
1. See “Maintenance ” and “Lubricati on”
sections.
56
Page 57
Motor
NOTE: Motors used on wood working tool s are particularly susceptible to the accumu-
lation of sa wdust and wood ch ips a nd sho uld be bl own o ut or “ Vacuumed” frequently to
prevent interf erence with normal motor ventilation.
TroublePro bable CauseRemedy
Excessiv e Noise 1. Motor1. Have motor check ed b y qualified
service technician. Repair service is available at your nearest
Auth orized Service Center.
Motor fails to
develop full
power. NOTE:
Low Voltage:
(Power output of
motor decreases
rapidly with
decr ease in voltage at motor terminals.
Motor starts
slowly or fails to
come up to full
speed
Motor overheats1. Motor overloaded
Motor stalls
(resulting in
blow n fuses or
tripped circuit
breakers)
1. Circuit overloaded with lights,
appliances and other motors.
2. Wiring circuit (extension cord)
too long or undersize.
3. General overl oading of power
company facilities. (In some
sections of the country ,
demand for electrical power
may exceed the capacity of
existing generating and distribution systems.)
4. Incorrect fuses or circuit
breakers in power line.
1. Low vo ltage.
2. Windings burned out or open.
2. Improper cool ing. (Air circulation restricted through motor
due to sawdust, accumulating
inside of saw.)
1. Voltage too low to permit
motor to reach operating
speed.
2. Fuses or circuit breakers do
not have suffi c i ent cap acity.
1. Do not use other appliances or
motors on same circuit when
using the saw.
2. Increase wire sizes, or reduce
length of circuit. See “Motor
Specifications and electrical
Requirem ents” section.
3. Request a voltage check from
the power company.
4. Install correct fuses or circuit
breakers.
1. Request voltage check from the
power company.
2. Have m otor repaired or replaced.
1. Feed work slower into blade.
2. Clean out sawdust to provide
normal air circulation through
motor. See “Maintenance” and
“Lubrication” section.
1. Request voltage check from the
power company.
2. Install prope r si ze f u ses or circuit
breakers.
Frequent opening of fuses or
circuit breakers
Motor runs intermittently, sparks
excessively or
fails to start
1. Motor overlo aded
2. Fuses or circuit breakers do
not have suffi c i ent cap acity.
1. Worn or damaged brushes1. Replace brushes. See “Mainte-
1. Feed work slower into blade.
2. Install prope r si ze f u ses or circuit
breakers.
nance” section.
57
Page 58
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
55
54
11
53
43
44
47
46
50
40
Parts List for RIDGID 10 Inch Table Saw
Model No. TS24001
Figure 1
1
2
45
41
44
57
10
61
43
58
5
4
59
6
16
17
19
65
49
13
56
60
52
51
48
42
18
11
3
4
5
1
15
9
66
See Figure 5
7
2
1
8
12
13
14
67
68
39
36
34
35
30
29
28
63
33
31
27
38
37
24
58
32
64
26
20
21
62
22
See Figure 3
23
See Figure 4
25
Page 59
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
Always Order by Part Number - not by Key Number
Parts List for RIDGID 10 Inch Table Saw
Model No. TS24001
Figure 1
Key
Part No.Description
No.
126317
1
827518
2
827545
3
73352
4
827478
5
159572-146
6
830397
7
809813-1
8
827872
9
104879
10
827533
11
830345
12
448013
13
830378
14
830396
15
827497
16
827870
17
808380-2
18
829971-8
19
9420474
20
826395
21
AC1000
22
808380-18
23
808275-4
24
827493
25
808380-5
26
830399
27
805475
28
830398
29
169123-2
30
138164
31
827925
32
827873
33
827921
34
827548
35
* Bolt Carriage 1/4-20 x 1
Mount Rail Extension
Table Extension
* Nut Hex Flange 1/4-20
Clip Fence
* Screw Hex Wash Hd Ty T
10-32 x 7/8
Scal e Rip
Screw Pan Rec 6-32 x 1/2
Spring Rip Scale
Screw Lock Set 10-32x3/16
Slider Rail
Cap Rail Front Right
* Screw Pan Hd Ty Ab N8x1/2
Rail Front
Cap Rail Front Left
Panel Front
Scale Bevel
* Screw Pan Hd #8 x 3/8
Base w/ Labels
* Screw Hex Wash Hd Ty T
10-32 x 1/2
Bezel Switch
†Key Switch
Screw Pan Hd #6 x 3/4
Plastite
* Screw Pan Hd 8-32 x 3/8
Foot Base
* Screw Pan Hd #8 Plastite
Plate Switch Box
* Nut Hex 8-32
Box Switch
Relief Strain
* Lockwasher #8
Bolt C arriage 1/2-13 x 1-1/2
Nut Push 1/2
Washer Flat Nylon
Wrench Arbor
Key
Part No.Description
No.
827874
36
808380-17
37
805550-5
38
830405
39
830406
40
274622
41
821521
42
827463
43
827482
44
827515
45
827523
46
827515-1
47
830377
48
827514
49
274205
50
805552
51
813051-5
52
830376
53
827645
54
827525
55
827470
56
509492
57
809374
58
826390
59
805297-12
60
138671
61
826347
62
829971-7
63
829971-6
64
805549-22
65
SP6499
66
SP6499S
67
SP6499F
68
* Standard Hardware Item - May be pur chased locally
† These parts are available where you purchased your saw.
Nut Wing Nylon 1/2-13
* Screw Pan Hd #10 x 3/4
Plastite
Washer 7/32 x 5/8 x 1/16
Cord w/Plug
Wrap Cord
Screw Hex Hd Ty T
1/4-20 x 1
Screw Hex Hd Shoulder .312
Bolt T 1/4- 20
Coupling 1/4-20
Link Locking Front
Pivot Linkage
Link Locking Rear
Bearing Rail Lock
Lever Table Lock
Nut Lock 1/4-20
* Washer 17/64 x5/8 x 1/16
* Screw Pan Hd 1/4-20 x 2-3/4
Ta ble Main
Cap Rear Rail Left
Rail Rear
Cap Rear Rail Right
Insert Asm
Screw Flat Hd 10-32 x 1
Insert Ind-I-Cut
Screw Soc Flat Hd
5/16-18 x 1
Screw Set 5/16-18 x 5/8
Switch Locking
Circuit Asm
Switch Reset Asm
Washer #1 0
13/64 x 3/8 x .031
Owners Manual - English
Owners Manual - Spanish
Owners Manual - French
59
Page 60
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
1
Parts list for RIDGID 10 Inch T ab le Saw
Model No. TS24001
Figure 2
12
11
13
10
5
2
3
4
9
8
6
18
7
47
14
48
51
50
49
16
15
42
21
36
38
41
40
39
35
18
33
37
34
32
30
31
60
29
24
23
28
17
2425
27
21
19
20
21
22
3
2
52
26
43
44
4546
Page 61
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
Always Order by Part Number - not by Key Number
Parts List for RIDGID 10 Inch Table Saw
Model TS24001
Figure 2
Key
Part No.Description
No.
827483
1
370625
2
827619
3
827540
4
141594-46
5
824334-1
6
805550-5
7
808380-17
8
827459
9
827862
10
827522
11
827500
12
827519
13
830390
14
830391
15
37937
16
809372-7
17
827467
18
829971-9
19
821421-11
20
805561-4
21
805641-4
22
60136
23
827496
24
802612-8
25
830381
26
Cover Blade
* Screw Hex Wash Hd
1/4-20 x 1 /2
Plate Bevel Stop
Support Bev e l Indicator
* Screw Soc Cap
1/4-20 x 5 /8
Indicator
* Washer 7/32 x 5/8 x 1/16
* Screw Pan Hd #1 0 x 3/4
Bar Locking
Clamp Asm Bevel
Pivot Bevel Lock
Handle Bevel Lock
Mount Front
Knob Asm Bevel
Handle Asm Elevation
* Washer 17/64 x 5/8 x 1/32
* Screw Pan Hd 10-32 x 5/8
Bushing Trunnion
Shaft Elevation Crank
(Includes “O” Rings)
Ring “O” 3/8 x 1/16
Washer .50 5 x 3/ 1 6 x 1/32
Ring Retaining 5133-50
* Washer 13/64 x 5/8 x 1/32
Gear Elevation
Nut Push 3/8
Motor Asm
Key
Part No.Description
No.
827863
27
827864
28
830412
29
9420474
30
808380-17
31
827476
32
60249
33
60014
34
827520
35
827531
36
830380
37
827529
38
830394
39
827465
40
6362
41
830386
42
816768
43
826017
44
828064
45
828122-1
46
809398
47
830385
48
60415
49
830393
50
830392
51
830250
52
* St andard Hardware Item - May be purchased locally
Screw Set Nylon
10-32 x 3/4
Nut Hex Nylon 10-32
Arbor Asm
*Screw Hex Ty T
10/32 x 1/2
* Screw Pan Hd #10 x 3/4
Chute Sawdust
* Nut Lock 3/8- 16
* Washer
.380 x 47/64 x 3/32
Mount Rear
Shaft Guide
Cradle
Shaft Elevation
Blade 10" 24T Carb.
Collar Blade
Nut Arbor
Spring
Brush
Holder Brush
Cover Motor Rear
Screw Wash Hd Cr M4-10
Nut Weld
Spacer Elev Lock
Washer Spring
Knob Elevation Lock
Knob Swivel
Cover, Brush
61
Page 62
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
Parts List for RIDGID 10 I nch Ta b le Saw
Model No. TS24001
Figure 3 - Miter Ga ug e Ass em bl y
1
16
15
14
13
12
11
10
Always Order by Part Number - Not by Key Number
Key
No.
–
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
* Standard Hardware Item - May be purchased locally
Pin, Miter
* Lockwasher #8
* Screw, Pan Hd 8-32 x 5/8
Screw Flat Hd. M6 x 1.0-16
Rod, Miter Gauge
Screw, Flat Head
Washer, “T” Slot
* Nut Hex 6- 32
Screw Pan Hd. 6-32 x 5/8
Screw, Set 5 x 0.8-5
2
3
4
5
6
7
8
9
62
Page 63
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
Parts List for RIDGID 10 Inch Table Saw
Model No. TS24001
Figure 4 - Fence Assembly
26
25
1
2
3
4
5
6
7
8
24
23
10
1
11
12
14
20
22
21
20
17
19
18
15
16
17
Always Order by Part Number - not by Key Number
Key
Part No.Description
No.
–
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
830421
809492-5
824350-1
820129
274865
9416390
824328-1
824332
824349-1
824342-1
827507
9422329
809372-3
60136
830281
830426
827532
Fence Complete
Screw Pan Hd. Ty “T” 8-32x1
Cap Channel Rear
* Nut Lock 5/16-18
* Washer 21/64 x 5/8 x 1/ 16
* Sc re w Pan Hd. Ty “T”
10-32 x 5/ 8
Plate Lock
Spring Lock
Slide Rear Fence
Rod Fenc e Loc k
Housin g R ip Fenc e
* Scr Hex Hd TY “T”
1/4-20 x 3/4
* Screw Pan 10-32 x 1/2
* Washer 13/64 x 5/8 x 1/ 32
Indicator
Head Rip Fence
Slide Fence Head
Key
Part No.Descri ption
No.
809169-3
17
822138-1
18
62636
19
824326
20
830425
21
824329
22
827876
23
828173
24
824330-1
25
829971-10
26
806752-2
27
829706
28
Hardware for Attaching Wood Facing
159653-3
805552
115120
* St andard Hardware Item - May be purchased locally
9
13
28
27
*Screw Pan Hd. Ty “T”
8-32 x 3/8
* Nut Sq 10-32
* Nut Sq 1/4-20
Bearing Ball Angular Contact
Lever Cam Fence
Pin Cam
Label RIDGID
* Screw Hex Washer Hd.
1/4-20 x 3/4
Plate Fence Channel
Channel Fence
Screw Pan Hd Ty “T”
10-32 x 1-1/4
Micro Adjust Asm
Bolt Sq. Hd. 1/4-20 x 3/4
* Washer 17/64 x 5/8 x 1/16
* Nut Hex 1/4-20
63
Page 64
Repair Parts
RIDGID parts are available on-line at www.ridgidparts.com
5
4
22
4
21
Parts List for RIDGID 10 Inch Table Saw
Model No. TS24001
Figure 5 - Guard Assembly
3
4
2
1
5
6
8
7
8
16
17
20
15
17
18
19
18
4
2
3
12
14
11
10
13
Always Order by Part Number - not by Key Number
Key
Part No.Description
No.
–
1
2
3
4
5
6
7
8
9
10
827499
62519
827646
827648-1
805549
60012
827649-1
62390
802612
826466
827536
Guard Complete
Spring, Pawl
Spacer, Pawl
Pawl
*Washer,
13/64 x 9/16 x 1/32
Nut Lock 10-32
Support, Guard
Pin Gu ard 1/4 x 1-3/4
Nut Push 1/4
Guard w/Label
Spreader Blade
Key
Part No.Description
No.
803422-163
11
827541
12
827877
13
62636
14
827511
15
805461-7
16
114604
17
37937
18
806214-3
19
179793
20
806214-4
21
827647
22
* St andard Hardware Item - May be purchased locally
9
Pin, Roll 3/16 x 15/16
Support Spreader
Mount Sprea der
Nut Square 1/4-20
Knob Guard
Screw Hex Hd 1/4-20 x 1
* Lockwasher Ext 1/4
* Washer 17/64 x 5/8 x 1/ 32
Screw Soc Cap 10-32 x 7/8
* Screw Hex Hd 1/4-20 x 5/8
Screw Soc Cap 10-32x1-1/2
Spacer Support
64
Page 65
Notes
65
Page 66
Notes
66
Page 67
Notes
67
Page 68
RIDGID® HAND HELD AND STATIONAR Y POWER TOOL
LIMITED THREE YEAR WARRANTY AND
90 DAY SA TISFACTION GUARANTEE POLICY
This product is ma nufactured under license from Ridgid, I nc . by One W or ld
Technologies, Inc.. All warrant y communications sho uld be dir ec ted to One
World Technologies, Inc. at (toll free) 1-866-539-1710.
90-Day Satisfaction GuaranteePolicy
During the first 90 days after the date of purchase, if you are dissatisfied
with the performance of this Ridgid® tool for any reason, you may return
the tool to the dealer from which it was purchased for a full refund or
exchange. To receive a replacement tool you must present proof of purchase and return all original equipment packaged with the original product.
The replacement tool will be covered by the limited warranty for the balance of the three yea r war ra nty period.
What i s cover ed unde r the Lim ited Three Year Warranty
This warranty covers all defects in workmanship or materials in this
RIDGID® to ol for the three year p er iod from the date of pu r ch as e. This warranty is specific to this tool. Warranties for ot her RIDGID® products may
vary.
How to obtain service
To obtain service for this RIDGID® t ool y ou m ust return it, freight prepaid, to
an authorized RIDGID® service center for hand held and stationary power
tools. You may obtain the location of the authorized service center nearest
you by calling (toll free) 1-866-539-1710 or by logging on to the RIDGID®
website at www.ridgidwoodworking.com. When requesting warranty service, you must present the proof of purchase documentation, which
includes a date of purchase. The authorized service center will repair any
faulty workmanship, and either repair or replace any defective part, at our
optioon at no char ge to you.
What is not covered
This warranty applies on ly to the original purchaser at retail and may not be
transferred. This warranty only covers defects arising under normal usage
and does not c ov er any malfunction, failure or defect resulting from m is us e,
abuse, neglect, alteration, modification or repair by other than authorized
RIDGID® service center for hand held and stationary power tools. One
World Technoligies, Inc. makes no warranties, representations or promises
as to the quality or performance of its power tools other than those specifically s ta ted in th is warranty.
Additi onal Limitations
To the extent permitted by applicable law, all implied warranties, including
warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed
under state law are limited to three years from the date of purchase. One
World Technologies, Inc. is not responsible f or direct, indirect, incidental or
consequential damages. Some states do not allow limitations on how long
an implied warranty lasts and/or do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations may not
apply to you. This warranty gives you specific legal rights, and you may
also have other ri ghts which vary from state to state.
Stock No. TS2400
Model No. TS24001 Serial No. ________
Model and serial numbers may be found on the left rear
side of the base.You should record both model and serial
number in a safe place for future use.