RIDGID SP6263 User Manual
RS1000
OWNER’S MANUAL
10 INCH RADIAL SAW
For Your Safety:
Read all instructions carefully
Save this manual for future reference
Part No. SP6263 PrintedinU.S.A.
Table of Contents
Section Title Page
Safety .................................................................. 3
Introduction.............................................................. 12
Assembly ............................................................... 12
Adjustments ............................................................. 19
Alignment ............................................................... 28
Controls ................................................................ 37
ElectricalConnections ..................................................... 42
Crosscutting ............................................................. 45
Ripping................................................................. 49
CuttingAids ............................................................. 58
O.S.H.A.Requirements .................................................... 61
Accessories ............................................................. 62
Maintenance............................................................. 63
Troubleshooting .......................................................... 65
RepairParts ............................................................. 70
2
Safety
This manual has safety information and
instructions to help users eliminate or
reduce the risk of accidents and injuries,
including:
1. Severe cuts, and loss of fingers or other
body parts due to contact with the blade.
2. Eye impact injuries and blindness, from
being hit by a thrown workpiece, workpiece
chips or pieces of blade.
3. Bodily impact injuries, broken bones and
internal organ damage from being hit by a
thrown workpiece.
4. Shock or electrocution.
5. Burns.
Major Hazards
Three major hazards are associated with
usingthe radial arm saw for ripping. They
are outfeed zone hazard, kickback and
wrong way feed.
This section only briefly explains these hazards. Read the ripping and crosscutting
safety sections for more detailed explanations of these and other hazards.
Outfeed Zone Hazard
Safety Symbol and Signal Words
An exclamation mark inside a triangle is the
safety alert symbol.
It is used to draw attention to safety information in the manual and on t he saw. It is
followed by a s ignal word, DANGER,
WARNING or CAUTION, which tells the
level of risk:
DANGER
tion is not followed someone will be seriously injured or killed.
WARNING
tion is not followed someone could be seriously injured or killed.
CAUTION
tion is not followed someone may be injured.
Read and follow all safety information
and instructions.
: means if the safety informa-
: means if the safety informa-
: means if the safety informa-
If you reach around the blade to the outfeed
side when ripping, and try to hold down or
pull the workpiece through tocomplete a cut,
the rotational force of the blade will pull your
hand back into the blade.
Fingers will be cut off.
Read and follow the information and
instructions under ripping safety.
3
Safety
Kickback Hazard
Kickback is the uncontrolled propelling of the
workpiece back toward the user during ripping.
The cause of kickback is the binding or
pinching of the blade in the workpiece. Several conditions can cause the blade to bind
or pinch.
When a workpiece kicks back, it could hit
hard enough to cause internal organ injury,
broken bones, or death.
Read and follow the information and
instructions under ripping safety.
Wrong Way Feed Hazard
Wrong way feed is ripping by feeding the
workpiece into the outfeed side of the blade.
The rotational force of the blade can grab
and pull the workpiece.
Before you can let go or pull back, the force
couldpull your hand along with the workpiece into the blade. Fingers or hand could
be cut off.
The propelled workpiece could hit a
bystander, causing severe impact injury or
death.
Read and follow the information and
instructions under ripping safety.
4
Guard Function and Features
The guard is a very importantsafety feature,
designed to reduce the risk of injury associated with blade contact. Install the guard
correctly. Follow the specific instructions
in the ripping and crosscutting sections
to set and use the guard correctly for
each type of cut.
Guard Features Include:
1. A non-moveable metal upper portion,
(Upper Guard) which is fastened to the
motor by the guard clamp screw, and which
fullycovers the upper half of the blade.
2. A moveable clear plastic portion, (Plastic Lower Guard) which partially covers the
lower half of the blade. It protectsagainst
contact with the side of the blade during
crosscutting when blade is in its rearmost
position and the guard is resting on the
table, so the leading and trailing teeth of the
blade are not exposed. It also protects
against contact with the outfeed side of the
blade during ripping,andacts as a barrier to
prevent wrong way feed.
Safety
Handle/Squeeze
Trigger
3. A squeeze trigger in the saw handle to
fully raise the clear plastic guard at the start
of a crosscut. Note:
This is necessary because
the guard will not automatically raise to clear the
fence.
4. A hold down to be lowered to just clear
the top of the workpiece for ripping. It acts as
abarriertotheinfeedsideoftheblade,
keeps the workpiece fromfluttering,andacts
as a sawdust deflector. It is locked/unlocked
by the hold down knob.
5. A riving knife tobeloweredtothetable
forripping. It keeps the workpiecekerf open,
thereby reducing blade pinching and the risk
of kickback. It also acts as a barrier to the
hazardous outfeed side and prevents wrong
way feed. It is locked/unlocked by the riving
knife/pawls knob. When lowered for crosscutting, it acts as a barrier to the leading
edge of the blade.
Upper Guard
Hold Down
Knob
Hold Down
Plastic Lower
Workpiece
Guard
Pawls, Riving
Knife Knob
Riving
Knife
Pawls
5
Safety
6. Set of pawls tobeloweredtotheworkpiece surface for ripping. They allow the
workpiece to pass freely from infeed to outfeed side, but help stop the kickback motion
fromoutfeedtoinfeedsidebygrabbinginto
the workpiece surface. Pawls must be reset
each time a different thickness workpiece is
cut.
7. A guard tab to manually raise the plastic
guard at the start of ripping unusual workpieces whose size/shape do not cause the
guard to raise automatically.
Hazards Associated with Clear Portion of Guard
The following safety information applies to all
blades and accessories.
WARNING
Clear plastic portion of guard w ill not
provide any protection during crosscutting if blade is pulled over your
hand, or your hand enters blade path
from front or rear of blade. Fingers or
hand can be cut or cut off.
Guard Tab
CAUTION
Clear plastic portion of guard can get
caught or jam in fence or table kerfs.
Read and follow the warning on the
guard:
WARNING:
TO AVOID INJURY
SHUT OFF P OWER
BEFORE CLEARING A
JAMMED LOWER GUARD
Clear plastic guard will increase risk of certain hazards:
• During rip and bevel cuts, narrow cut
off pieces can be pinched between
guard and blade. Cut-off pieces can
kickback.
• In bevel position blade teeth are fully
exposed. Fingers or ha nd can be cut
off.
6
WARNING
• Cut-off pieces can jam between
guard and blade. Turn saw off and wait
for blade to stop before freeing
jammed guard or blade.
• Workpiece or cut-off pieces can be
violently thrown by blade. Wear safety
goggles. Stand out of workpiece path.
Safety
Safety Instructions
Read and follow all safety instructions.
Personal Safety Instructions
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known (to the State of California)
to cause cancer, birth defects or other
reproductive harm. Some examples of
these chemicals are:
• Lead from lead-bases paints,
• Crystalline silica from bricks and
cement and other masonry products, and
• Arsenic a nd chromium from chemically-treated lumber.
Your risk from these exposures varies,
depending on how often you do this
type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust
masks that are specially designed to
filter out microscopic par ticles.
2. Turn saw off, remove yellow key, and
unplug before leaving work area. Do not
leave until bladehas stopped spinning.
3. Make work area child-proof: remove yellow key to prevent accidental start-up; store
key out of sight and reach; lock work area.
4. Keep floorsclean and free of sawdust,
wax and other slippery materials.
5. Keep work area well lighted and uncluttered.
6. Use saw only in dry area. Do not use in
wet or damp areas.
Safety Goggles
Dust Mask
1. Wear safetygoggles labeled ANSI Z87.1
(or in Canada CSA Z94.3-99) on the package. It means the goggles meet impact standardsset by the American National
Standards Institute. Regular eyeglasses are
not safety goggles.
2. Wear close fitting clothes, short sleeved
shirts, and non-slip shoes. Tie up long h air.
Do not wear gloves, ties, jewelry, loose clothing, or long sleeves. These can get caught in
the spinning blade and pull body parts into
the blade.
3. Wear dust mask to keep from inhaling
fine particles.
4. Wear ear protectors, plugs or muffs if you
use saw daily.
5. Keep good footing and balance; do not
over-reach.
Work Area Safety Instructions
1. Keep children, pets, and visitors out of
work area; they could be hit by a thrown
workpiece, workpiece chips or pieces of
blade.
Ear Protectors
7
Safety
Saw Safety Instructions
1.Useguard,pawlsandrivingknifeaccording to instructions. Keep them in working
order.
2. Routinely check saw for broken or damaged parts. Repair or replace damaged
parts before using saw. Check new or
repaired parts for alignment, binding, and
correct installation.
3. Unplug saw before doing maintenance,
making adjustments, correcting alignment,
or changing blades.
4. Do not forcesaw. Use saw,blades and
accessories only as intended.
5. Have yellow key out and saw switched
off before plugging in power cord.
Workpiece Safety Instructions
6. Beforeturningonsaw,cleartableofall
objects except workpiece to be cut and necessary fixtures, clamps, or feather-boards.
7. If blade jams, turn saw off immediately,
removeyellowkey,thenfreeblade.Donot
trytofreebladewithsawon.
8. Turn saw off if it vibrates too much or
makes an odd sound. Correct any problem
before restarting saw.
9. Do not layout, assemble,or setup work
with saw on, or while blade is spinning.
10. Keep saw table clean.
11. Store items away from saw.Do not climb
on saw or stand on saw table to reach items
because saw can tip over.
1. Cut only wood, woodlike or plastic materials.
Do not c ut m et al.
2. Cut only one workpiece at a time. Stacking or placing workpieces edge to edge can
cause user to lose control of workpiece.
8
3. Rip only workpieces longer than the
diameter of the blade. Do not rip workpieces
that are shorter than the diameter of the
blade being used.
4. Workpieces that extend beyond the saw
table can shift, twist, rise up from the table,
or fall as they are cut or afterwards. Support
workpiece with table extensions the same
height as the saw table.
5. To prevent tipping, support outer ends of
extensions with sturdy legs or an outrigger.
Safety
Dia.
6. Do not use another person to help support workpieces or to aid by pushing or pulling on workpieces, because these actions
can cause kickback. Use table extensions.
7. Useclampsorvicetoholdworkpiece.It's
safer than using your hands.
Blade Safety Instructions
1. Use only blades marked for at least 3450
rpm.
2. Use only 10" or smaller diameter blades.
3. Use blades for their recommended cutting procedures.
4. Keep blade sharp and clean.
5. Do not overtighten blade nut because
blade collar could warp.
6. Do not turn saw on and off in rapid
sequence because blade can loosen.
7. Blade should stop within 15 seconds after
saw is switched off. If blade takes longer, the
saw needs repair. Contact Authorized Service Center.
9
Safety
On-Product Safety Labels
There are several safety labels on the saw.
They alert the user to hazards explained in
the manual and remind the user how to
avoid the hazard.
At the out feed side, t o t he right of the
guard near the saw handle is this safety
label to alert you to wrong way feed:
Note where they are located on the saw.
Read and follow the safety information
and instructions in these labels. Refer to
the manual for de tailed explanations and
instructions.
On the infeed side of the guard is this
safety label to remindyoutolowerthe
hold down to just clear the top of the
workpiece for ripping:
Ontherearoftheyoke,visible from the
infeed side when the saw is in a rip position,
is this safety label to alert you to outfeed
zone hazard:
10
On the clear plastic guard is this OSHA
required label:
Onthebottom surface of the m otor, visible
when the cutting tool is horizontal, is this
safety label alerting you to use a guard
when edge molding, and to position the
cutting t ool behind the fence:
(see Accessories Section)
Safety
Near the saw handle is this safety label to
alert you to thrown objects andtoremind
you to wear safety goggles:
On the front of the yoke is this general
safety instruction label:
11
Assembly
Introduction
In order to get the most enjoyment out of your radial saw it is important that the machine be properly assembled, adjusted, and aligned. This procedure, although not difficult, takes time; perhaps
eighthours or longer for the inexperienced user. However, after this initial set-up a weekly tune-up
can be completed in approximately ten minutes by checking the alignment and only adjusting those
settings which are incorrect.
Identify Parts
The following parts are included:
Note:
parts are included If you are missing any par t, do not
assemble the saw. Contact 1-800-4the missing part. Sometimes small par ts can get lost
in packaging material. Do not t hrow away any packaging unt il saw is put t ogether.Check packaging for
missing par ts before contacting
parts list (Repair Parts) is at the end of the manual.
Use the list to identify the number of the missing part.
This model includes:
Before beginning assembly, check that all
RIDGID
RIDGID
A. Basic Saw Assembly ........................... 1
B. Rear Table ........................................... 1
C. Spacer Table ........................................ 1
D. Fence (wooden) ................................... 1
E. Front Table ........................................... 1
F. Table Support ...................................... 2
G.Loose Parts Bag(s)
H. Bag Containing
Accessory Guard.................................. 1
J. Leg ....................................................... 4
K. Stiffener, Side ...................................... 2
L. Stiffener, Front/Rear ............................ 2
............................ *
to get
.Acomplete
A
BC
Remove protective
covering from arm trim
D
F
E
GH
* Number varies; bags can contain other
smaller bags. Note:
To make assembly easier
keep contents of each bag together and separate from
contents of other bags.
12
K
J
L
Assembly
5/16-18 x 3/4" Long
Square Head Screw (4)
1/4-20 x 1" Long
Pan Head Screw (4)
1/4-20 x 1-3/ 4" L ong
Pan Head Screw (1)
#6-32 x 1/2 Pan Head Screw (4)
#10-32 x 7/8" Long
Pan Head Self Threading Screw (2)
1/4-20 x 1" Long
Slotted Cup PointSet Screw (1)
5/16" Diam. Hex Nut (4)
1/4" Di am . Hex Nut (4)
1/4" Hex “L” Wrench (1)
3/16" Hex “L” Wrench (1)
Wrench (2)
17/64" Flat Washer (5)
11/32" x 7/8" x 1/16"
Flat Washer (4)
5/16" Lockwasher (4)
1/4" Lockwasher (4)
Tee Nut (1)
Rip Scale Indicator (2)
Yellow Key (1)
1/4" U-Clip (1)
Twin Nut (2)
Table Clam p Assem bly (2)
- Thumbscrew
- Square Nut
- Clamp Bracket
- Cup Washer
13
Assembly
Crank
Arm Cap
1/4" Diam. x 5/8" Long
Truss Head Screw (24)
Leveling Foot (4)
3/8" Diam. Hex Nut (8)
5/16" Diam. Hex Nu t (4)
1/4" Di am . Hex Nut (24)
Tools Needed for Assembly and Alignment
1/4" External Tooth
Lockwasher (24)
5/16" Diam. External
Lockwasher (4)
11/32" x 11/16" x 1/16"
Washer (8)
5/16"Diam.x5/8"Long
Hex Head Screw (4)
14
7/16-inch Wrench
1/2-inch Wrench
9/16-inch Wrench
Small Hammer
5/8-inch Wrench
15/16-inch Wrench
1/8" Hex Wrench
Pliers
Pencil
Medium Screwdriver
Phillips Screwdriver
Framing Square
Assembly
WARNING
Plugging in saw during assembly
could result in electrical shock, or
severe cuts from contact with spinning
blade.
Do not plug in s aw at any time during
assembly.
Plug in saw only when it is to be used.
Assembly Steps
It is important for your safety and to get
accurate cuts that you p ut the saw together
according to these instructions. Follow these
steps in order.
Assembling steel legs
For easy assembly it is recommended to finger tighten all screws, lockwashers, and hex
nuts until the legset is fully assembled. Then
go back and tighten all nuts securely.
From among the loose parts, find the following Hardware:
24 Truss Head S c rews, 1/4-20 x 5/8
24 Lockwashers, 1/4-External
24 Hex Nuts, 1 /4-20
8 Hex Nuts, 3/8 - 16
4 Leveling Feet
1. Insert three truss head screws through
the three holes near the top of one Leg.
Place the Side Stiffener up to the Leg, as
shown, so that the three screws line up with
the holes in the Side Stiffeners ma r ked with
an "X" in the illustration.
2. Place a lockwasher and hex nut on each
screw and finger tighten the hex nut.
3. Followingthesameprocedureasabove,
continue to fasten together the remaining
Legs, Side Stiffeners, and Front/Rear Stiffenersasillustrated.
5. Set stand upright and securely tighten all
nuts.
6. To level steel legs,loosen nut on inside of
leg and turn nut on outside to raise or lower
feet. Adjust all four levelers if necessary, and
then tighten nuts on inside of leg.
Note:
These levelers are not intended for height
adjustment.
X = Location of Truss Head Screws
Front/Rear
Stiffener
Side
Stiffener
Leveling Foot
Truss H ead
3/8" Hex Nuts
Screws
4. Install one 3/8-16 hex nut completely onto
each of the leveling feet. Insert one leveling
foot through hole in bottom of each leg and
install a 3/8-16 hex nut.
15
Assembly
Mounting Saw
1. Fromamong the loose parts, find the following hardware:
4 H ex Head Screws, 5/16-18 x 5/8
4 Lockwasher, 5/16 in. Exter nal Type
8 Washers,11/32 ID
4 Hex Jam Nuts, 5/16-18
2. Place saw on legs so that holes in bottom
ofsawlineupwithholesmarkedXintopof
legs and RIDGID logo on leg set is facing
front.
3. Install screws, washers and nuts as
shown.
4. If you mount the saw on any other
RIDGID base or flat bench, make sure Elevation Crank has proper clearance to rotate.
The saw must be bolted down. Position saw
toslopeslightlyrearward,sowhenthecarriage is installed it w ill not roll forward due to
gravity.
Saw Base
Hex Head
Screw
Flat Washer
Stiffener
Flat Washer
Lockwasher
Hex Nut
Leg
Side
Stiffener
Front Stiffener
Leg
WARNING
Saw must slant slightly towards rear to
keep blade carriage from rolling forward. Workpiece or saw can move
unexpectedly if leg set rocks. Fingers,
hand or arm could be cut off by blade
contact. Adjust leveling feet before
using s aw.
Attach Elevation Crank.
Install crank on elevation shaft. Be sure setscrew is tightened o n flat of shaft.
Elevate arm approximately 3 to 4 Inches.
Remove shipping block and discard.
16
Shipping Block
Elevation Crank
(Turn clockwise
to raise arm)
Attaching Carriage - Motor to Arm
Remove carriage stop screw, lockwasher
and tag. Read and understand warning tag
before discarding tag.
Lock miter/arm lock before proceeding.
Holding carriage assembly with both hands,
carefullystartandslidethecarriageontothe
tracks. The assembly must be held parallel
with the arm so that all four bearings slide
smoothly onto the arm, preventing any
excessive strain on bearings and track.
Warning
Tab
Lockwasher
Stop Screw
Hex “L” Wrench 1/4 Inch
Push toward rear of
saw to lock
Assembly
(Supplied)
Miter/Arm
Lock Lever
WARNING
Reinstall carriage stop screw and lockwasher to prevent carriage f rom rolling
off arm. Tighten carriage stop screw
securely.
Note:
threaded into bottom of motor
Removetwo (2) motor packing studs t hat are
.
Install arm cap.
WARNING
Make certain power cord is unplugged.
Packing
Studs
Bottom
of Motor
Arm Cap
Screw
1. Insert finger under left end of switch lever
and pull out to the "ON" position.
2. Placearmcapinpositionandinstallwith
(2) 10-32 x 7/8 self th reading screws.
3. Push switch to "OFF" position.
Reinstall carriage
stop screw and
lockwasher
17
Assembly
Remove saw blade.
1. Tightencarriage lock knob, located on
rightsideofarm.
2. Loosen guard clamp screw approximately
4 turns. Rotate dust elbow so opening is facing left.
3. Use one hand to lift the clear plastic
guard at the front of the saw.
4. Use the other hand to grasp the rear of
the guard (below the dust elbow).
5. Rotate the entire guard assembly forward
approximately 45°.
6. Re move the guard assembly.
7. Motor shaft has left hand threads. Hold
shaft wrench and rotate arbor wrench down
(clockwise).
8. Remove shaft nut, outer collar, saw
blade, and inner collar. Set aside and out of
the way.
Pull down
to loosen
Blade
Rotation
Attach Table Supports
1. Set out:
- two table supports
- four 5/16" 18 x 3/4" long square head
screws
- four 11/32" x 7/8" x 1/16" flatwashers
-four5/16"lockwashers
- four 5/16" hex nuts
2. Attach supports to side frame, making
sure to use correct holes in table supports
and side frame: Use two screws per support
(insert screws through base and then support); on end of each screw put a flat
washer, lockwasher and nut then finger
tighten so table supports rest in lowest position.
Table
Support
Screws
Here
Nut
Lockwasher
Flatwasher
Square Head Screw
5/16 - 18 x 3/4"
Table
Support
Base
Front
Mount rails using
these holes
This concludes the assembly section. Except for installing table boards, fence, and table clamps
the saw should be completely assembled. The next section deals with adjusting your saw to
remove any "looseness" in order to get accurate cuts.
18
Read “Controls” section and familiarize yourself with control names and location before
beginning “Adjustments”.
Adjustments
Arm Lock Adjusting Wheel
With the arm at an "unindexed" position
(other than 90° or 45°) and the miter lock
applied, the locking action should feel tight
and secure.
Considerable effort should be required to
move the a r m back towards 0°. It i s a lways
possible to force the arm because of the
leverage advantage the long arm provides.
However,the arm should resistmovingwhen
a reasonable amount of force is applied.
To check follow these steps:
1. Pull miter/arm lock forward to unlock and
rotate arm to approximately 30° left or right.
2. Lock miter/arm lock by pushing handle
toward rear of saw.
Miter/Arm
Lock Lever
3. Apply pressure as shown above.
4. If the arm moves easily:
a.)Unlock miter lock.
b. Locate the adjusting wheel as shown.
c. Turn wheel clockwise to tighten, coun-
terclockwise to loosen.
5. Repeat steps 1, 2, 3 above and readjust
as necessary.
Tighten
Arm Lock
Adjusting Wheel
19
Adjustments
Yoke Clamp Adjustment
To check the yoke clamp adjustment follow
these steps:
1. Pull the yoke lock handle towards the
front of saw to unlock yoke. Pull forward on
theyokeindexlever(ontheleftsideofcarriage) to disengage index pin.
2. Swivel the motor halfway between the
crosscutting and rip position so the index pin
is not engaged.
3. Lock the yoke lock handle.
4. Grasp the motor with both hands and try
to swivel it back into the crosscut position. It
should not move.
5. If it does move follow these steps:
a. Remove arm cap.
b. Remove carriage stop screw and lock-
washer with a 1/4 inch hex-L wrench.
Yoke Lock
Handle
Arm Cap
Lockwasher
c. Grasp the carriage assembly, move it
carefully off the end of radial arm, holding
it parallel to the radial arm until all carriage bearings are free of their tracks.
d. Rest the motor and carriage assembly
on saw frame.
e. Set yoke lock handle at unlocked position. Tighten nut with 15/16" wrench, until
lock handle locks mid-way between the
two legs of the yoke.
f. Hold the motor and carriage assembly
parallel to radial arm and start the rear
bearings onto the tracks. Continue to hold
the assembly parallel to the tracks until
the forward bearings are on the tracks.
g. Slide the carriage rearward on the
radial arm and installthe carriage stop
screw and lockwasher.
h. Repeat steps 1-4. Readjust if necessary.
i. Install arm cap.
Carriage Stop
Screw
15/16" Wrench
Screw
Hex “L” Wrench
(1/4-Inch)
WARNING
Reinstall carriage stop screw and lockwasher to prevent carriage from rolling
off arm.
20
Bevel Lock Lever
The purpose of the bevel locklever is to lock
the motor at any angle. To check follow these
steps:
1. Unlock the bevel lock lever. Move the
bevel index pin to the left and rotate the saw
to approximately 30°. Lock the bevel lock
lever.
2. Use both hands as shown and try to force
them otor out of position. If the motormoves,
the bevel lock lever needs to be tightened.
On the other hand if it is extremely hard to
lock the bevel lock lever it has been over
-tightened.
3. Follow these steps to adjust:
a. Remove the socket cap screw with hex
wrench as shown.
Adjustments
Bevel I ndex
Pin
Bevel Lock
Lever
b. Use the bevel lock lever as a wrench to
tighten or loosen the clamp bolt. Do not
over tighten.
c. Repeat steps 1 and 2. Re-adjust if necessary.
d. Replace bevel lock lever in the locked
position.
e. Tighten the socket cap screw.
Note:
The clamp bolt has a left handed thread.
Therefore, to increase the clamping effect, rotate the
bevel lock lever - when used as a wrench -from right to
left, or clockwise when viewed from above. If you accidentallyrotateit the wrong way and disengage the bolt
from the matching steel nut, it will be necessary to
remove the Yoke Handle, and Bevel Scale, in order to
reinstall the bolt into the nut.
Bevel Lock
Lever
Lockwasher
Socket Cap Screw
1/8" Hex “L” Wrench
Bevel Lock Lever
In Locked Position
21
Adjustments
Arm to Column Adjus tment
If you can move the end of the radial arm up
and down when the arm is unlocked, adjust
as directed below:
a. Remove two (2) screws from rear cover
plate. Tighten evenly top two 3/8-16 bolts
until the play is removed and the arm will still
move side to side freely .There should be no
vertical or horizontal movement in the arm
when miter/arm lock is locked and unlocked.
3/8-16 Bolts
b. Bottom two nuts should be snugged
ev en ly, but not nearly as tight as top two bolts.
c. Re-install Rear Cover Plate.
Adjusting Column Tube in Column Support
This adjustment will remove any looseness
between the column tube and column support while serving two purposes:
• To insure accurate cuts; and
• To allow the column tube to raise and
lower smoothly.
Note:
The following adjustment is
very critical
.
Allfuture alignmentprocedures rely on t his adjustment
being per formed correctly. All looseness must be
removed.
This section is set up in two sections:
Alignment checks and adjustments. It is very
important that the column tube and the
inside of the columnsuppor t are coated with
a film of uncontaminated lubricant.
Alignment Checks
Twochecks are required, theseare adjusted
at the factory, but may have shifted during
shipment.
1. Index and lock arm at 0° Miter.
Vertical Alignment Check:
2.
The two piece column support needs to be
compressed by tightening the black and silver screws to properly control the movement
of the column tube. Precise alignment is
done only by tightening or loosening the silver 5/16-18 screws in combination with the
brass set screw. Push up slightly on the end
of the arm. Look for a noticeable movement
between the column tube and the column
support.
3/8-16 Nuts
Upward
Pressure
Look for Movement
Between Column Tube
and Support
22
3. Rotational Alignment Check:
While holding the arm with one hand, hold
fingers of other hand as shown, between column tube and column support. Apply gentle
side-to-side pressure at end of arm. Any
side-to-side or rotational movement can be
felt with finger at arrow location.
Alignment Adjustments
Adjustments
Note:
not
IfVer tical Alignment wasOK and adjustmentis
needed, proceed to step 6.
1. Loosen (2) 1/4 - 20 Gib socket cap
screws on the left side at the rear of the column support slightly (1/2 turn).
Vertical Adjustment:
2.
Using the closed end of a box wrench, tighten
all of the 5/16-18 black screw heads on the column support casting 1/16th to 1/8th of a turn.
Tighten the (2) 5/16-18 silver screw heads
slightly more than the black ones to achieve a
close fit to the column tube (Fig. 2). (A 1/4"
drive ratchet with a six point socket may be
needed to get enough torque on bolts.) Loosen
nut on brass set screw . Tighten the brass set
screw firmly and retighten nut (Fig. 2).
3. Elevate and then lower the Arm using the
elevation crank.
4. If the column tube binds and elevation is
difficult, go back to step 2 and loosen the
screws until you achieve smooth but firm elevation, recheck step 3.
5. Repeat "Vertical Alignment Check
".
Fig. 1
Front
Brass Set Screw
Bright Plated
Bolts
Tighten
Loosen
Fig. 2
a. If vertical misalignment still exists,
repeat steps 2 through 4.
b. If vertical misalignment no longer
exists, and you have achieved smooth but
firm elevation, proceed to step 6.
6. Rotational
Adjustment:
Tighten the (2) 1/4-20 Gib socket cap screws
until no noticeable rotational playexists.(Fig. 3).
7. Repeat "Rotational Alignment Check"
a. If rotational misalignment still exists,
repeat step 6.
b. If rotational misalignment no longer
exists, and you have achieved smooth but
firm elevation, this alignment procedure is
complete.
Front
Gib Socket
Capscrews
Hex “L” Wrench
(Supplied)
Fig. 3
23
Adjustments
Adjusting Carriage Bearings
If the carriagebearingsare loose it not only
allows the saw blade to move up, down, and
sideways but also results in inaccurate cuts.
Before following these steps make sure the
tracks (steel rods) and carriage bearings
have been cleaned by wiping them with a
clean cloth.
When properly adjusted, the top and bottom
face of all four bearing grooves should be in
contact with the arm tracks for their entire
length and carriage should roll smoothly with
some resistance.
To test for looseness between bearings and
tracks on radial arm, perform the following
steps.
1. Remove left-hand carriage cover.(2 screws)
2. Push the carriage to its full rearward position.
3. Grasp front carriage bearing as shown
and hold as tight as possible. At the same
time pull carriage forward. If you can stop the
bearing from turning, it requires adjusting.
Wipe track on
each side with
a clean cloth
Remove Carriage
Cover
4. Check rear bearingin the same manner.
5. Adjust as follows:
a. Hold the eccentric screw in place with
a 9/16" wrench. Use a 1/2" wrench to
loosen the nut on the bottom just enough
to permit the e ccentric screw to turn.
b. Rotate the e ccentric screw a partial
turn (left or right) as required to take up
looseness.
c. Hold the head of eccentric screw in the
position established in the preceding step
and tighten nut on underside of carriage.
Correct adjustment exists when you cannot keep the bearings from turning. However, excessive bearing pressure will
cause difficult operation and rapid wear.
d. Install carriage cover.
Eccentric
Screw
Carriage
Plain
Washer
Washer
Assembly
Carriage
Bearing
Lockwasher
Nut
Left Side Carriage Bearings
24
Loading...