NA3 / NB2
(VT3600 / 2600 / 2630, Ges 5380/5360, Rex 1285/1270, NSA CP380/360, ABD 6770)
Parts standardization with other models (NA3 only)
New Parts
No.
DescriptionRank
Adjusting Plate - Exit Pawl
(C218)
Pressure On / Off Lever
(C218)
Q’ty Used
Old→→New
1 → 1
1 → 1
1 → 1
Volt/Hz
Inter-
change-
ability
X/X X/O as a set1337
X/X1037
X/O1837
Parts needed for replacement by new part
Part No.DescriptionNo.Page
Date of
Modification
Serial
Number
Parts
Catalog
Rank: A : Replace with new parts immediately. B : Replace with new parts at time of repair.C : Replace with new parts at time of overhaul.
Interchangeability:
(1) When old and new parts are not mutually interchangeable, use additional parts or an assembly part as indicated in "Parts needed for
replacement by new part" to install the new part.
(2) The mark to the left of the slash indicates whether the old part can be used in the new machine, and the mark to the right indicates whether
the new part can be used in the old machine. x = Not interchangeable o = Interchangeable
MODIFICATION BULLETIN NO. 1 PAGE 2 OF 4
ISSUED ON: May 15, ’95
DETAILS OF MODIFICATION
The following three parts have been change d to the ones wh ich are used in oth er mod els.
- Press Roller Shaft
A flat face has been added on the shaft as shown on the next page.
- Adjusting Plate - Exit Pawl
Due to the ad de d fla t face on the shaft, the conn ect ing part has been lowered 2 mm.
- Pressure ON / OFF Lever
To ensure that th is part is fixed to the adjusting plate in the exact correct posit ion and that it
does not move durin g op era tion, the distance between the two screw holes has been increased.
(The position of the screw holes on the adju stin g pla te side has also cha ng ed .) This part can be installed
with the old typ e ad just ing plate because it has a screw hole for the old adjusting plate (C2 09 55 70 ).
This part is needed only when the optional A4 drum is used .
The press roller shaft and exit pawl adjust ing plate are fixed by a bolt (# 05950140E ), and these new parts can
prevent the bolt from b ein g broken due to excessive stress.
C209 6159C227 6159End Fence Spring - Large
C209 6181Front Guide Plate
No.
NA3 / NB2 (VT3600/ 2600/ 2630, Ges 5380/5360, Rex 1285/1270, NSA CP380/360, ABD 6770)
Component parts of the paper delivery table
To stack copies more evenly on the paper delivery table
New Parts
No.
Description
C219 6150Delivery Table Unit (C219-A4) (RICOH)
C219 6160Delivery Table Unit (C219-LT) (NRG)
C219 6165Delivery Table Unit (C219-A4) (NRG)
Q’ty Used
Old→New
0 → 1
0 → 1
0 → 1
2 → 2
Inter-
change-
ability
X / O547
Parts Catalog
NO.Page
*
*
*
1 → 0
C227 6146Rear Guide Fence
0 → 1
X / X2247
47
47
47
CodeModel Name
Note
The old description was incorrect.
Serial
Number
C209 6182Rear Guide Fence
C209 6142Guide Fence Slider
C209 6149C227 6157Guide Fence Spring
Interchangeability:
The mark to the left of the slash indicates whether the old part can be used in the new machine,
and the mark to the right indicates whether the new part can be used in the old machine.
x = Not interchangeable o = Interchangeable
C227 6147Front Guide Fence
C227 6142Guide Fence Slider
1 → 0
0 → 1
3 → 1
0 → 2
2 → 2
The old description was incorrect.
X / X2347
1647
X / O*34 47*: New Index
X / O2847
H. Kokubo,
Priport Service Planning Section
MODIFICATION BULLETIN NO. 2
Page 2 OF 4
ISSUED ON: July 15th, ’96
Draw
No.
Old Parts
No.
C2096145C227 6145Guide Fence Bracket
C209 6184C227 6184End Fence
C209 6156Sponge Seal - 4.5 x 65 x 175
To stack the copies more evenly on the paper delivery table,
some component parts of the table have been changed
as described on the previous pages. (For details, refer to
RTB-012.) The new illustration is shown below.
Page 3 OF 4
ISSUED ON: July 15th, ’96
* : New Index
MODIFICATION BULLETIN NO. 2
Page 4 OF 4
ISSUED ON: July 15th, ’96
MODEL NAME
Ges 5380 / Rex 1285 /
NSA CP380
Ricoh VT3600120/60USA, CanadaC218-17Service part only
A.B.Dick 6770120/60USA, CanadaC218-18Service part only
Ges 5380 / Rex 1285 /
NSA CP380
Ricoh VT3600220, 240/50EuropeC218-27Service part only
Ricoh VT3600220, 240/50AsiaC218-29Service part only
Ges 5360 / Rex 1270 /
NSA CP360
Ricoh VT2630120/60USA, CanadaC219-17No production
Common3C2174594Rear Bank Plate (C219)1
Common14C2174592Front Bank Plate (C219)1
Common*29C2174597Sponge - Rear Bank Plate1
Common*30C2174596Sponge - Front Bank Plate1
See Drawing 7
MODIFICATION BULLETIN NO. 3
ISSUED ON: July 31, ’96
Page 9 OF 36
NRG/ABD/RICOHIndexPart NumberDescriptionQ’ty
Common*31C2184558Front Doctor Roller Ring (C218)1
Common*32C2184559Rear Doctor Roller Ring (C218)1
Common*33C2184560Ring Spring (C218)2
Common*34C2094713Hose Clamp (C218)2See Drawing 8
Common30C2092587Pad - Plotter Lower CoverPad - Plotter Lower Cover (C218)
Common31C2092585Plotter Base Pad -SmallPlotter Base Pad - Small (C218)
Common32C2092599Lower PadLower Pad (C218)
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.