Ricoh is330dc QUICK GUIDE

QUICK INSTALLATION GUIDE<G412-6685>

100mm or more

ZDLH040E

660mm or more

ZDLH050E

ZDLH200E

ZDLH206E

Please read the Safety Information in the Setup Guide or Scanner Reference before using
this machine. It contains important information related to USER SAFETY and PREVENTING
MACHINE PROBLEMS.

Color Scanner

UNP ACKING THE SCANNER
AND CHECKING THE CON­TENTS OF THE BOX

Check the contents of the box according to the
following list. If one or some items are missing,
please contact your sales or service
representative.

○○○○○○○○○○○○

Quick Installation Guide (this sheet)
Setup Guide
Scanner Reference

CD-ROM
Power Cord
Tools

Registration Card (North America only)

Remove the plastic bag. Lift the scanner and move
it to the place where you want to install it.

WHERE TO PUT THE
SCANNER

○○○○○○○○○○○○○○○○○○○○

The scanner’s location should be carefully chosen
because environmental conditions greatly affect its
performance.

Optium Environment Conditions

Recommended temperature and humidity

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

%RH

80

15 C

60

40

20

%RH

80

60

40

20

The machine must be level within 5 mm,0.2" both front to rear
and left to right.

70%

15 C
30%

10 C 15%

10 20 30

59 F
70%

59 F
30%

50 F 15%

50 70 8060 90

Possible operation range Recommended range

27 C 80%10 C 80%

25 C
70%

25 C
30%

32 C 15%

80.6 F 80%50 F80%

77 F
70%

77 F
30%

89.6 F 15%

32 C
54%

89.6 F
54%

Environments to Avoid

Important!

• Locations exposed to direct sunlight or

strong light

• Dusty areas

• Areas with corrosive gases

• Areas excessively cold, hot, or humid

• Locations near an air conditioner or humidifier

• Locations near other electronic equipment

• Locations where the scanner might be subjected to

frequent strong vibration

Space Required for Installing the Scanner

Leave enough space around the scanner. This
space is necessary to operate the scanner. The

Open the automatic document feeder (ADF) and

○○○○○○○○○○○○○○○

remove the protective sheet on the contact
glass.

recommended (or minimum) space requirement
is as follows.

C

INST ALLING THE SCANNER

F

TDLH140E

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

CAUTION

• This scanner weighs approximately 28 kg.

• When lifting, please make sure to lift slowly so as to
minimize physical strain with two persons or more while
holding onto the handles located in the center on both
sides. Failure to lift using proper caution, reckless
handling or allowing the scanner to drop can cause injury.

DISENGAGING THE LOCK

ZDLH025E

Set the lock switch on the left side of the
scanner to the “Unlock” position.

Take out the scanner main unit.

○○○○○○○○○○○○○○

WARNING

• Confirm that the wall outlet is near the machine and
freely accessible, so that in event of an emergency, it
can be unplugged easily.

• Only connect the machine to the power source de­scribed on this sheet.

• Avoid multi-wiring.

• Do not damage, break or make any modifications to the
power cord. Do not place heavy objects on it, pull it
hard or bend it more than necessary. These actions
could cause an electric shock or fire.

CAUTION

• Keep the machine away from humidity and dust. A fire
or an electric shock might occur.

• Place the machine on a strong and level surface.
Otherwise, the machine might fall and cause personal
injury.

• If you use the machine in a confined space, confirm
that there is a continuous flow of air.

Power Connection

Connect the power cord to a power source with
the following specifications:

Product Specifications

North America

Europe

Electrical Outlet Requirements

North America

Europe

G412-17 power supply rating:

AC 120V, 60Hz, 2A

G412-27 power supply rating:

AC 220-240V, 50/60Hz, 1A

G412-17 Electrical Outlet Requirements:

AC 120V, 60Hz, min.10A

G412-27

Electrical Outlet Requirements:

AC 220-240V, 50/60Hz, min.5A

Remove the tape (a through d).

ZDLH215E

Please refer to the “Setup Guide” for information
about other procedures to be performed
following installation.

G412-6685 EE GB

UE USA