Ricoh 3800C, G566 Installation Manual

Caution

•

Before installing options, the machine should be turned off and unplugged f or at least thirty minutes.

Mail Bin Type 3800C

(Code: G566)

For Machine Code: G060 / G080 / G082
INSTALLATION GUIDE

Components inside the machine become very hot, and could result in a burn if touched.

•

When lifting the machine, use the grips on both sides. The machine could break or cause injury if
dropped.

•

It is dangerous to handle the plug with wet hands. Doing this may result in receiving an electric
shock.

•

Before moving the machine, unplug the power cord from the outlet. If the cord is unplugged
abruptly, it could become damaged. Damaged plugs or cords can cause an electrical or fire
hazard.

•

When moving the 4-bin mailbox, hold the center of both sides , and lift slo wly. Lifting carelessly or
dropping it may cause injury.

•

When installing the 4-bin mailbox, be sure to hold both sides. If you hold it by the bottom, you
might get your hand caught and injured.

Important

❒

Check the printer nameplate to confirm the model code.

❒

If you want to use the optional paper feed unit at the same time, install the optional paper feed unit first, and then install the 4-bin mailbox.

❒

You cannot install the 4-bin mailbox and 2 tray finisher at the same time.

❒

The 4-bin mailbox weighs approximately 7kg (15.5lbs).

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Check the contents of the box for the following items:

Description Q’ty

Mailbox 1

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Screws 2
Output Bin 4
Labels 1
Installation Guide(This sheet) 1

Slowly open the front cover by pulling on the two areas
on the left and right.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Be sure to check the following points:

•

The power is turned off.

•

The power cord is unplugged from the wall outlet.

•

The interface cable is unplugged from the printer.

Remove the green screwdriver, and then close the front

ZDJH007J

cover.

Use this screwdriver for all attachment and detachment of screws.

Remove the attached packaging.

Note

❒ Do not remove the adhesive tape fastening the cable yet. Remove

it in step

.

ZDJP087J

ZHXH171J

Note

❒ After using the screwdriver, return it to its original position on

the inside of the front cover.

G566-8600B

Remove the top cover. Draw the lever (a), and then lift

b

) to remove it.

(

There is an opening for installing the 4-bin mailbox.

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

If the duplex unit is installed, open the duplex reversal
unit.

A

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

Push up the lock release button, and leave it in that
position.

Note

ZDJP089J

❒ You cannot use the removed cover.

Holding both sides of the 4-bin mailbox with both hands,
stand on the left side of the printer. Slowly lower it into the
openings, and then insert until you hear a click.

ZDJP090J

Note

❒ If the duplex unit is installed, proceed to step .

Pull up the external tray in the direction of the arrow
and then remove

(b).

(a)

,

ZHXH380J

B

Slowly lower the duplex reversal unit, until it stops.

ZDJP093J

Open the upper left cover.

ZHXH390J

ZDJP038J