Ricoh FT3013-S Technical Bulletin FT3013

Technical Bulletin No. RTB-001

SUBJECT: Service Manual Correction DATE: April 30, ’95

PAGE: 1 of 1

PREPARED BY: S. Hizen
CHECKED BY: M. Iwasa

CLASSIFICATION:

Action Required
Troubleshooting
Retrofit Information

User-Code 0 (U-0)
The User-code 0 (U-0) is missing in the code section of your service manual page 4-24.

Please add the User-code 0 in your service manual.
U-0:
The first scanner may accidentally move away from its home position during transportation

/ location change of the machine. If the main switch is turned on under this condition, U-0
appears.

Solution:
Turn the main switch off and on to eliminate the U0 code.

Revision of service manual
Information only
Other

FROM: 2nd Technical Support Section

MODEL:

Robin

NOTE: U-0 is different from E21/E22. The scanner home position sensor has no problem

for U-0, while the sensor may be defective for E21/E22.

Technical Bulletin No. RTB-002

SUBJECT: Upper Unit Opening Problem DATE:May 15, ’95

PAGE: 1 of 5

PREPARED BY: S. Hizen
CHECKED BY: M. Iwasa

CLASSIFICATION:

Action Required
Troubleshooting
Retrofit Information

- Problem ­When the upper unit without the document feeder is released, it tends to open very

abruptly.

- Cause ­The torsion spring force is too strong.

- Temporary countermeasure for the production machines ­To reduce the torsion force, parts of the front and rear angle brackets which support the

torsion spring have been cut off as shown:

Revision of service manual
Information only
Other

FROM: 2nd Technical Support Section

MODEL:

Robin (A151 / A152)

Part cut off

The cut-in serial numbers for this modification are as follows:

Machine Code Cut-in Serial Number Machine Code Cut-in Serial Number

A151 - 10 26740900 01 A152 - 10 26940900 01
A151 - 15 1A240900 01 A152 - 15 1A340900 01
A151 - 16 From 1st Production A152 - 16 From 1st Production
A151 - 17 A3604092 283 A152 - 17 A36140 90001
A151 - 22 26641000 01 A152 - 22 26840900 01
A151 - 24 From 1st Production A152 - 24 From 1st Production
A151 - 25 26641000 89 A152 - 25 26840902 16
A151 - 26 3F21040001 A152 - 26 3F30940001
A151 - 27 A3604100 001 A152 - 27 A36140 91301
A151 - 28 From 1st Production A152 - 28 From 1st Production
A151 - 29 A3604103 600 A152 - 29 A36140 92170

Technical Bulletin No. RTB-002

[A]

SUBJECT: Upper Unit Opening Problem DATE: May 15, ’95

PAGE: 2 of 5

- Permanent countermeasure for the production machines ­To make it possible to adjust the force of the upper unit opening in the field, the

configurations of the front and rear angle brackets have been changed as shown.

Old

P/N A0771098

P/N A0771197
(Torsion Bar
Angle - Front)

The Cut-in serial numbers for this modification are as follows:

Machine Code Cut-in Serial Number Machine Code Cut-in Serial Number

A151 - 10 26750300 01 A152 - 10 26950200 01
A151 - 15 1A250300 01 A152 - 15 1A350200 01
A151 - 16 2675030051 A152 - 16 ---­A151 - 17 A3605030 154 A152 - 17 A36150 30945
A151 - 22 26650200 01 A152 - 22 26850300 01
A151 - 24 ---- A152 - 24 ---­A151 - 25 26650201 16 A152 - 25 26850301 21
A151 - 26 3F20350001 A152 - 26 3F30350001
A151 - 27 A3605030 001 A152 - 27 A36150 30001
A151 - 28 ---- A152 - 28 ---­A151 - 29 A3605030 754 A152 - 29 A36150 32090

(Torsion Bar
Angle - Rear)

New

P/N A1521198
(Torsion Bar Angle Bracket-Rear)

P/N A15211 97
(Torsion Bar Angle (S/Ns of Dec. production
unit will be put in) - Front)

- How to adjust the force of the upper unit torsion spring -

1. Make sure that the main switch is turned off and
the power supply cord is unplugged.

2. Remove the platen cover or DF.

3. Open the front cover.

4. Remove the following covers and units.

• Development unit

• Upper rear cover

• Upper left cover [A]

5. Remove the front and rear upper unit stoppers [B] (1 screw each).

[B]

Technical Bulletin No. RTB-002

Stronges t
Setting

A

•Screw

SUBJECT: Upper Unit Opening Problem DATE: May 15, ’95

PAGE: 3 of 5

6. Open the upper unit gently while holding it until the upper unit stops at the 90° position
as shown.

7. Remove the inner cover [D] (2 screws).

8. Adjust the force of the
torsion spring as
follows:

A

•Screw•Screw•Screw

A

Front

B

C

B

Factory
Setting

Torsion
Spring

- Factory Setting -

- Strongest Setting -

• Remove screw C
on both sides

• Loosen screw A
on both sides

• Shift the
adjusting bracket
toward the
torsion spring.

• Tighten screws
on both sides in
positions B and A.

Factory
Setting

Torsion
Spring

C

Rear

B

B

A

C

Stronges t
Setting

C