REVELL Performa M20 User Manual
Revel®P erforma™M20 Loudspeaker
TABLE OF CONTENTS
INTRODUCTION...............................................3
ABOUT THE MANUAL AND WARRANTY.................................3
DESCRIPTION .................................................4
WOOFER ..........................................................................4
TWEETER .........................................................................5
CROSSOVER NETWORK .....................................................5
CABINET...........................................................................5
UNPACKING....................................................6
INSTALLING GRILLES (OPTIONAL).....................7
INSTALLING STANDS (OPTIONAL) .....................8
PLACEMENT..................................................10
ROOM ACOUSTICS...........................................................12
ROOM TREATMENT..........................................................12
CONNECTIONS ..............................................14
SYSTEM OPTIMIZATION ..................................15
CABINET CARE ..............................................16
LOUDSPEAKERS AND POWER ........................17
SERVICE INFORMATION ..................................17
SPECIFICATIONS............................................18
REVEL PERFORMA M20
Owner’s Manual
2
Figure 1. The REVEL
PERFORMA M20
loudspeaker (without grille).
INTRODUCTION
Revel®leads the loudspeaker world in research, advanced
engineering techniques, and unique production processes. The
REVEL PERFORMA
™
M20 loudspeaker is the perfect demon-
stration of Revel’s unparalleled engineering capabilities.
The REVEL PERFORMA M20 loudspeaker is a compact model
with technology derived from advanced engineering used in Revel’s
famed Ultima
™
loudspeakers. Each one has an inverted magnesiumalloy dome woofer and custom aluminum-alloy dome tweeter to
achieve outstanding freedom from coloration. We also use our
groundbreaking measurement process to seamlessly integrate the
superb transducers with an optimized network to achieve stunning
realism and superb dynamics.
As a result, the REVEL PERFORMA M20 loudspeaker sets a
whole new standard in bookshelf loudspeaker sound quality. Its
superior performance, assured by our ongoing research, will greatly
contribute to the enjoyment of music or film sound in your home.
ABOUT THE MANUAL AND WARRANTY
To begin enjoying your new loudspeakers, first read and then perform
the instructions in this owner’s manual. Maximum performance
depends on following all instructions described here, as well as those
found in the owner’s manuals of associated components in your audio
system. Save these instructions for future reference.
REVEL PERFORMA M20 loudspeakers are covered by a limited
5-year warranty, so save the bill of sale to protect your purchase
and aid in any service-related questions.
REVEL PERFORMA M20
Owner’s Manual
3
Figure 2. Transducer and connection locations for the REVEL
PERFORMA M20 loudspeaker.
DESCRIPTION
The REVEL PERFORMA M20 loudspeaker features a transducer
complement (see Figure 2) of one 6.5-inch (165 mm) woofer and a
1-inch (25 mm) tweeter.
Combined with an individually-optimized crossover network, this
transducer arrangement results in a superior off-axis response that
provides a large “listening window” and an uncolored in-room
response, even in the presence of strong wall reflections.
WOOFER
The 6.5-inch (165 mm) woofer with an inverted magnesium-alloy
dome features:
• True pistonic operation for increased freedom from coloration.
• Shielded magnetic circuits to prevent interference with
video monitors.
• Butyl rubber surround for large, linear excursion capabilities.
• Vented center-pole piece for better cooling and low compression.
• Die-cast basket to eliminate resonances.
• 1.5-inch (38 mm) Kapton
®
voice-coil former with flat, edge-
wound voice coil.
• 26-ounce (0.737 kg) motor system with flux shorting ring to
dramatically reduce modulation distortion.
REVEL PERFORMA M20
Owner’s Manual
4
+1-1
0
+.5
-.5
Tweeter Level (dB)
Stand
Mounted
Flush
Mounted
Revel
Northridge, California
Made in U.S.A.
Serial Number
Placement
Compensation
(See Owner's Manual)
xxxx
REVEL PERFORMA
M20 Front
(without grille)
Woofer
Woofer Port
Tweeter
REVEL PERFORMA
M20 Rear
Tweeter
Level
Control
Placement
Compensation
Control
Connectors
TWEETER
The 1-inch (25 mm) tweeter with aluminum-alloy dome features:
• True pistonic operation for increased freedom from coloration.
• Underhung with copper-clad aluminum wire for low distortion.
• Ferrofluid for better power handling with reduced compression.
• Shielded magnetic circuits to prevent interference with
video monitors.
• Flux modulation ring for very low distortion
CROSSOVER NETWORK
Each REVEL PERFORMA M20 loudspeaker has an individuallyoptimized crossover network with:
• A high-order crossover at 2.2 kHz to optimize the on- and offaxis response of the system.
• Filter networks with carefully selected components for optimum
performance with vanishingly low coloration and distortion.
• External Placement Compensation Control for optimizing the
loudspeaker’s response for flush-mount, bookshelf, or standmount applications.
• External Tweeter Level Control provides high-frequency compensation for a variety of room environments.
CABINET
The cabinet is constructed of 1-inch (25 mm) thick MDF walls
with extensive internal bracing for unshakable performance.
A rounded front baffle is sculpted to reduce diffraction, and three
cast aluminum feet adorn the cabinet for superior coupling to any
surface. The wood-veneer cabinet comes in finishes of Cherry,
Sycamore, Rose, or Black Ash.
The optional REVEL PERFORMA PEDESTAL 1 is also available
from your Revel dealer. This stand is designed to optimize the
acoustical performance and enhance the appearance of the REVEL
PERFORMA M20 loudspeaker. It attaches securely to the loudspeaker cabinet, and the loudspeaker feet attach to the base of the
stand to create an integrated and attractive appearance (also see
Installing Stands on page 8).
REVEL PERFORMA M20
Owner’s Manual
5
WARNING
Figure 3. A REVEL
PERFORMA M20 loudspeaker
with its inner packing materials.
UNPACKING
IMPORTANT! To avoid injury, please use care during unpacking.
Always stand as straight as possible and use your leg muscles to lift
the REVEL PERFORMA M20 loudspeaker. Do not lift it while
bending from the waist.
Each REVEL PERFORMA M20 loudspeaker is packed in its own
carton. To unpack it, perform the following steps:
1. Place a REVEL PERFORMA M20 loudspeaker onto its side.
2. Open the bottom flaps. Stand the unit in the up position.
3. Open the top flaps. Take out the spike foot kit and set it aside.
Remove the top pad.
4. Lift the carton off the loudspeaker and set it aside, being careful
not to damage the cabinet.
5. Grasping the cabinet on the sides, lift it up and remove the bottom pad. Use caution to avoid touching any of the transducers.
6. Repeat steps 1 through 5 for the other loudspeaker.
NOTE: Spikes can be installed as an option after determining final
speaker placement. Installation is similar to instructions shown in
Figure 7 on page 9.
REVEL PERFORMA M20
Owner’s Manual
6
+1-1
0
+.5
-.5
Tweeter Level (dB)
Stand
Mounted
Flush
Mounted
Revel
Northridge, California
Made in U.S.A.
Serial Number
Placement
Compensation
(See Owner's Manual)
xxxx
Top Pad
Bottom Pad
Spike Foot Kit
Warranty Card and
Owner’s Manual
Loading...