When using electrical appliances, basic precautions should
always be observed, including the following.
READ ALL INSTRUCTIONS BEFORE USING
For additional protection, the installation of a residual
current device (rcd) having a rated residual operating
current not exceeding 30 mA is advisable in the electrical
circuit supplying the bathroom. Ask your installer for advice.
WARNING - TO REDUCE THE RISK OF BURNS,
ELECTROCUTION AND FIRE OR INJURY TO PERSONS
DANGER - As with most electrical appliances, electrical
parts are electrically live even when the switch is off.
• The appliance should never be left unattended when plugged
into a power outlet, except when charging the appliance.
• This appliance should not be used by children or other
persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children without
supervision.
• Never operate this appliance if it has a damaged cord or
plug, if it is not working correctly, if it has been dropped or
damaged, or dropped into water. If the supply cord or plug
of the appliance is damaged it must be replaced by the
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard. It cannot be repaired. Keep the
cord away from heated surfaces.
• Charge, use and store the product at a temperature between
0°C and 32°C.
• Do not use outdoors or where aerosol (spray) products are
2
Page 3
being used, or where oxygen is being administered.
• Do not use this appliance with damaged or broken tracks,
foils or cutters, as injury may occur.
• For use on facial hair only. Not intended for shaving the hair
on your head.
• Do not plug or unplug the appliance with wet hands.
• For household use only.
• Do not place or store the appliance or charging adaptor
where it can fall or be knocked into a sink or bath.
• Do not place in or drop into water or any other liquid for
extended periods of time.
• If an appliance falls into water, “unplug it” immediately. Do
not reach into the water.
• Unplug the charging adaptor from the electrical outlet
immediately after fully charging.
• Unplug and switch off this appliance before cleaning it.
• Use this appliance only for its intended use as described in
this manual.
• Do not use attachments not recommended by Remington.
• Never drop or insert any object into any opening of this
appliance.
• Always store the charging adaptor in a moisture-free
location.
• Do not use on people who are asleep.
• Do not use an extension cord or a voltage converter with this
appliance.
• Do not wrap the cord around the appliance.
Remington strongly recommends that an approved Safety Switch
(Residual current device) be installed to protect all bathroom
power outlets. Ask an electrical contractor for advice.
SAVE THESE INSTRUCTIONS
3
Page 4
XF8550AU SMART EDGE ADVANCED HYBRID SHAVER
USE & CARE INSTRUCTION MANUAL
Thank you for purchasing your new Remington® SMARTEDGE Shaver.
Inside this manual you will find tips on using and caring for your shaver.
2
3
4
7
8
1
5
6
KEY PARTS
1. On/off switch
2. SmartEdge™ Cutting System
3. Inner Foil
4. Hair pocket
5. 3 stage charge indicator
6. Power port charge pins
7. Foil assembly release buttons
Charging stand,
travel position
9
8. Pop up trimmer (not shown)
9. Charging stand
Charging stand,
charging position
Also Includes
• Head guard
• Power adaptor
• Cleaning brush
4
Page 5
XF8550AU SPECIFICATIONS
Power SystemLithium Rechargeable
Full Charge Time2 hours
Cordless Shave Time50 minutes
Quick ChargeYes
IndicatorsCharging/Low Battery
Volt ag e TypeWorldwide
Replacement PartSPF -XFAU
WaterproofYes
Travel LockNo
Charging
ABC
BEFORE USING, READ THE IMPORTANT SAFETY INSTRUCTIONS IN
FRONT OF THE MANUAL.
1. Plug power adaptor into charging stand. (Diagram A)
2. Place shaver into charging stand. (Diagram B)
3. Charge shaver to a full charge before its first use.
4. Use shaver until recharge is required.
Quick Charge
A 5 minute quick charge will allow for 3 minutes of shaving.
CAUTION!
• Make sure the shaver and your hands are dry when charging the shaver.
• Always charge the shaver in a cool, dry place.
5
Page 6
Shaving
B
E
D
1. Press power button to turn on. (Diagram D)
2. Shave face and neck using short, circular strokes. (Diagram E)
3. Shaver can be used on a dry face or with shave cream or gel.
4. Shaver can be usd in the shower.
E
Shaving Tips With Gel or Foam (In Shower or Over the Sink)
We recommend that you use the shaver in the shower for optimal
performance.
NOTE: In order to ensure optimal performance, thoroughly rinse the
shaver head under water during and after shaving.
5. Apply water to face and neck area.
6. Apply shave gel or foam to applicable shaving area.
7. Rinse shaver head under water.
8. Shave face and neck using short, circular strokes.
9. Throughout the shave, regularly rinse shaver head under water to avoid residue
build up.
10. When finished shaving, rinse face.
11. Thoroughly rinse shaver head of all gel or foam.
12. Follow cleaning and care instructions located on page 8
6
Page 7
Shaving Tips (Dry)
• Ensure your skin is free of oils.
• Wait at least 15 minutes after getting up before shaving, to ensure your face is
free of puffiness that may be present from sleeping.
• Always hold the shaver at a right angle to the skin so that the screens are
touching the skin with equal pressure.
• Stretch skin with the free hand so hairs stand upright, making it easier for
them to enter the cutting chamber.
• Use moderate to slow, circular stroking movement.
• The use of short, circular motions in stubborn areas may obtain a closer
shave, especially along the neck and chin line.
• Do not press hard against the skin to avoid skin irritation and/or damage to the
shaver head.
**We recommend that you use your new shaver daily for up to four
weeks to allow time for your hair and skin to become accustomed to the
new shaving system**
7
Page 8
Page 9
Price each
Face Saver: Pre-shave Powder Stick
handling
Shaver Saver: Aerosol Spray Cleaner
Shaving Heads & Cutters for XF8550AU
Price each
QtyAmount
NZD
AUD
$
$
$14.95 NZD
$59.95 NZD
$11.95 AUD
$39.95 AUD
SP4
7.50
$
$
$
$
Sub Total
SP5$11.95 AUD $14.95 NZD
TOTAL
Postage &
Spectrum Brands Australia Pty Ltd
Locked Bag 3004
Braeside, VIC 3195
AUSTRALIA
SPF-XFAU
eplacement
Article
R
Remington is a Registered Trademark
of Spectrum Brands, Inc., or one
of its subsidiaries.
Page 10
Cleaning & Care
The shaver is a wet/dr y appliance. The shaver may be cleaned under warm
water.
NOTE: * *When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.**
CAUTION!
• To clean the external surfaces of the shaver, use a damp cloth. Do not use strong
detergents or other chemicals.
• To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer or
heater to dry the shaver.
Note: Lubricate cutters after rinsing.
CLEANING YOUR SHAVER
Note: We recommend following these steps after each use.
F
13. Remove the foil assembly by pressing the release buttons on both sides of the
head and lifting the foil assembly upwards to remove from the hair pocket.
(Diagram F)
14. Tap out excess hair shavings.
15. Rinse the head of the assembly under running water. (Diagram G)
16. Replace the head assembly by pacing the assembly on top of the hair pocket,
press down and click into place. (Diagram H )
Note: Lubricate teeth of trimmer with oil every six months.
G
H
10
Page 11
Battery Removal
DANGER: ONCE THE SH AVER HAS BEEN DISMANTLED FOR DISPOSA L, DO NOT
ATTEMPT TO REASSEMBLE AND/OR USE.
To Remove the Rechargeable Battery:
Note: We recommend following these steps after each use.
17. The battery must be removed from the appliance before it is scraped.
18. The appliance must be disconnected from the supply mains when removing the
bat tery.
19. Unplug shaver from the outlet to avoid risk of electrical shock.
20. Remove the head from the shaver.
21. Using a small screwdriver, carefully pry off the front panel of the handle housing.
22. Using a Philips screwdriver remove the screws from the front of the inner housing
and remove the cover.
23. Lift the circuit board out of the inner housing to expose the battery.
24. Cut the wire connecting the bat teries to the circuit board and remove the
batteries.
25. The battery is to be disposed of safely.
11
Page 12
Suitable for use in bath and shower.
This product conforms to radio frequency interference requirements
Any product purchased and used commercially carries a limited 90 Day Warranty.
REPLACING YOUR HEADS & CUTTERS
It is very important to replace your head and cut ters when necess ary to ensure a close,
comfor table shave without irrit ation. We recommend they be replaced every 6 months. Here are
some signs of head and cutter wear, indicating that replacement is needed:
• Irritation: As the heads get excessively worn you may experience some skin irritation. This
would be especially noticeable when you apply moisturizing lotion.
• Pulling: When the cut ters wear you may feel a sense of pulling and a loss of closeness when
you shave. This is an indication that it is time to replace your heads and cutters.
Replacement heads & cutters may be obtained from your local retailer, or directly from
Remington®. Simply fill out the enclosed accessory order form or alternatively your order can
be proces sed over the phone via the Remington® Ser vice Hotline - refer to page 12.
MONEY BACK OFFER – AUSTRALIA / NEW ZEALAND ONLY
If within 6 0 days you are not fully satisfied with your Remington® shaver, just return the shaver
with this completed coupon and a copy of your Australian/ New Zealand purchase receipt to
Remington®. In return, we will send you a cheque for the full purchase price of the shaver.
Please allow 6-8 weeks for your cheque to arrive.
Name:
Address:
City:
State: Postcode:
Contact No: Area Code: Ph:
Product Model number:
Is this the first Remington shaver you have owned/purchased? Yes No
What is the reason you are returning this product ?
12
Page 13
Spectrum Brands Australia Pty Lt d and Spectrum Brands New Zealand Limited
WARRANTY AGAINST DEFECTS
In this warranty:
Australian Consumer Law means the Australian consumer law set out in Schedule 2 to the
Competition and C onsumer A ct 2010;
CGA means the New Zealand Consumer Guarantees Act 1993;
Goods means the product or equipment which was accompanied by this warranty and
purchased in Australia or New Zealand, as the case may be;
Manufacturer, We or us means:
1. for Goods purchased in Austr alia, Spectrum Brands Australia Pty Ltd
ACN, 007 070 573; or
2. for Goods purchased in New Zealand, Spectrum Brands New Zealand Limited,
as the case may be, cont act det ails as set out at the end of this warrant y;
Supplier means the authorised distributor or retailer of the Goods that sold you the Goods
in Australia or in New Zealand; and
You means you, the original end-user purchaser of the Goods.
1. Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law, or the CGA. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also entitled
to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
2. The benefits provided by this Warranty are in addition to all other rights and remedies in
respect of the Goods which the consumer has under either the Australian Consumer Law
or the CG A. The original purchaser of the Goods is provided with the following Warranty
subject to the Warranty Conditions:
3. We warrant the Goods for all parts defective in workmanship or materials for the period of
two (2) years from the date of purchase ( Warranty Period). If the Goods prove defective
within the Warranty Period by reason of improper workmanship or material, we may, at our
own discretion, repair or replace the Goods without charge.
Warranty Conditions
4. The Goods must be used in accordance with the manufacturer’s instructions. This Warrant y
does not apply should the defect in or failure of the Goods be attribut able to misuse, abuse,
accident or non-observance of manufacturer’s instr uctions on the par t of the user. As far as
the law permits, the manufacturer does not accept liabilit y for any direct or consequential
loss, damage or other expense caused by or arising out of any failure to use the Goods in
accordance with the manufacturer’s instructions.
5. Exhaustible components (such as shaver heads, cutter s and foils) of the Goods are included
under this Warrant y only where there is a defect in workmanship or materials used.
6. The warr anty granted under clause 3 is limited to repair or replacement only.
7. Any par ts of the G oods replaced during repairs or any product replaced remain the proper ty
of the manufacturer. In the event of the Goods being replaced during the Warranty Period,
the warranty on t he replacement Goods will expire on the same date as for the Warranty
Period on the original Goods which are replaced.
13
Page 14
8. In order to claim under the warranty granted under clause 3 you must:
(a) Retain this warranty with your receipt /proof of purchase; and
(b) Return the Goods to us at the relevant address below or to the Supplier by prepaid
freight within the Warrant y Period accompanied with ( i) the legible and unmodified original
proof of purchase, which clearly indicates the name and address of the Supplier, the
date and place of purcha se, the product name or other product serial number and (ii) this
warranty.
9. This warranty is immediately void if:
(a) Any serial number or appliance plate is removed or defaced;
(b) The Go ods have been serviced or otherwise repaired by a person not authorised to do so
by us or where non approved replaced parts are used.
10. The Goods are designed for domestic use only. A limited 9 0-day Warranty applies to any
industrial or commercial use of the Goods. The Goods must be connected to the electrical
voltage requirements as specified in the ratings label located on the G oods.
11. This warranty does not cover the cost of claiming under the warranty or transport of the
Goods to and from the Supplier or us.
12. This warranty is only valid and enforceable in Austr alia against Spectrum Brands Australia
Pty Ltd and in New Zealand against Spectrum Brands New Zealand L imited.
Contact us or the Supplier for further details.
Spectrum Brands Australia Pty Ltd
Locked Bag 300 4
Braeside, VIC 3195
AUSTRALIA
Customer service in Australia: 180 0 623 118
E-mail: consumer.enquiry@remington-products.com.au
Website: www.remington-products.com.au
Spectrum Brands New Zealand Limited
PO Box 9817
Newmarket, Auckland 1149
NEW ZEALAND
Customer service in New Zealand: 0800 736 776
E-mail: info@remington.co.nz
Website: www.remington.co.nz